Professional Documents
Culture Documents
Public address systems of various scales are used in all fields of today's world for
various purposes at various locations. A system engineer designs a system suitable to
a specific application. In all cases, he starts it with preparing a system plan for the
customer, involving the purpose of use, budget, and specifications.
Toward achieving an appropriate system design within the budget of the system plan, it
is important to clarify the main purpose of acoustic devices to be used and to decide
whether to select or not to select incidental functions (such as additional functions
which may be of help if provided). It is also necessary in selecting system components
to carefully study not only their performance but the ease of operation and the use of
PA system as well as reliability (i.e., capability of performing the intended motion
whenever required). A general system design procedure is shown in the flow chart
given.
START
Quotation prepared
NO
Approved?
YES
INSTALLATION
The first problem raised in designing a public address system concerns the noise and
acoustic characteristics of the place where the system will be installed. Noise can be
generally classified into two kinds, that is, noise inside the building, and noise outside.
Noise inside the building includes, for example, the noises produced by the elevators
and air conditioners, talking people, machines at work, and the goods carried on the
floor. Outside noise may be such that produced by traffic, construction work, waves of
the sea, or running water in a river. It generally varies much depending on the kind of its
source, its distribution, the topography, and the buildings in the neighborhood. It can
also vary greatly from time to time. The acoustic characteristics can pose a problem
particularly when a public address system is installed indoors. The main factors
involved are reverberation and echo.
A room that has walls of a heavy and hard material with small acoustic absorptive (for
example, concrete, slate, or plywood walls) generally has a long reverberation time.
Specifically, slate covered factories in the shape of a dome, parking areas in buildings,
and gymnasiums have a long reverberation time. Reverberation lowers sound clarity,
and is detrimental to acoustics at low frequencies, particularly in rooms which are not
acoustically well designed. Echo is a reflection of the original sound heard later.
Reflected sounds reaching the ear within 1/20 second (50 mS) from the direct sound
reinforce the original sound so that they sound like a signal sound with reverberation. If
reflected sounds reach the ear later than that, the reflected sounds are heard as an
echo because they sound separate from the direct sound. The echo so seriously affects
sound clarity that it makes a music performance impossible. It is the most harmful of all
acoustic ill effects.
If noise level is higher than the level of the sound coming out of the speaker, the
speaker sound cannot be heard. No matter how close the speaker may be its sound
cannot be heard if noise level is too high. The required difference between speaker
sound and noise levels varies depending on the kind and degree of noise, but at least a
sound pressure difference of 6 to 10 dB (2 to 3 times) is necessary for making
announcements, or at least about 3 dB (about 1.5 times) for background music or other
music programs.
For your reference, noise levels at various locations are shown in me table below.
Noise Levels
Note: Generally, noise level is high at low frequencies, and low at high frequencies.
Noise level is measured with a noise meter, and measured noise levels in WRMS are
used.
Output sound pressure Speaker specifications include output sound pressure, which
represents the sound volume that can be produced by the speaker, measured by
applying a 1-watt input to the speaker and measuring the sound one meter away from
it.
Output sound pressure is expressed in decibels (dB), which is equal to phone used to
express noise used to express the same in noise calculations Output sound pressure
also represents the speaker capacity (or efficiency) of converting electrical signals into
sound, which varies from 85 dB to 110 dB with the kinds of speakers.
What will be the output sound pressure level if a higher input of 2 watts and more is
applied to the speaker? The output sound pressure increases as shown in the table
below.
The WT-715N is a horn type speaker called the CLEARHORN, which features a high
output sound pressure of 101 dB (1 m, 1 W). If a 15-watt input is applied to it, 101 dB+
11.8 dB = 112.8dB (1 m).
As is clear from the two examples above, the higher the output sound pressure, the
higher sound can the speaker produce more efficiently.
In terms of amplifiers, the same sound pressure can be obtained from a smaller powered
amplifier if the speaker has a high output sound pressure. Assume that we now have a
87-dB speaker and a 90-dB speaker here, for example;
What will be the total output sound pressure in dB if two or more speakers, each with an
output sound pressure of X dB, are installed in the same place in the same direction?
If a 1-watt input is applied to two 90-dB speakers, their total output sound pressure
increases by 3 dB to 93 dB, which is the same as when a 2-watt input is applied to one
of them.
If a 1-watt input is applied to three 90-dB speakers, the result will be same as when a 3-
watt input is applied to one of them. That is, the total output pressure increases by 5 dB
to 95 dB.
• Increased Sound Pressure Where Two or More Speakers of the Same Capacity
Are Installed in the Same Place
Incidentally, the rated output sound pressure of a speaker applies where a certain
specified sound source, not a speech or music, is used. In the past, the required sound
pressure was often calculated from the rated output sound pressure. This, however,
does not have a peak factor (allowance for speeches or music) so that .sound becomes
distorted at peak level
Therefore, we calculate the required sound pressure by adding the peak factor for the
peak of the program source to the required sound pressure difference, which is the
difference between noise level and the average sound pressure of the program source.
The peak factor (the difference between the average sound pressure and peak sound
pressure of a program source) varies from one program source to another, but it is 10
dB for speeches and background music, or 20 dB for music.
Music
The table below shows the required sound pressures at various locations
Speaker output sound decreases in volume as the distance from the speaker increases.
Sound volume (sound pressure) decreases in inverse proportion to the square of
distance.
The table below shows sound attenuation outdoors (wherein air density difference,
temperature difference, wind direction, reflection from obstacles, refraction, etc. are
ignored).
Sound attenuation indoors is less than that in free space, varying depending on the
acoustic characteristics of the room. Generally, public address systems are designed
with sound attenuation in free space as reference, using the above as peak factor.
Sound attenuation also varies with frequency. That is, a high-frequency sound
attenuates more than a low-frequency sound.
The sound pressure at a point a certain distance away from the speaker is calculated
as follows:
Suppose that the rearmost seats in an auditorium are 25 meters away from the
speakers. The speaker output sound pressure required to reach them at 80 dB level is,
by compensating for attenuation of the original sound pressure:
Example 1:
Step 1
Suppose that the noise level indoors is 60 dB. If the required sound pressure difference
is 6 dB, the required sound pressure will be, by adding a peak factor of 10 dB:
= 76dB.
Step 2
A sound pressure of 76 dB is required at the listening points, which are 1.7 meters
away from the speakers.
Step 3
To achieve a uniform sound pressure, the speakers are so arranged that their
directional angles cross at the listening points on condition that their service area is 90°
each.
Step 4
Selecting a speaker:
The WS-4150N was selected as a ceiling speaker. This speaker has an output sound
pressure of 92 dB (1 m, 1 W) so that enough sound volume can be obtained even if an
input of about 0.1 watt is applied to it.
Actually, the total input wattage is the input wattage per speaker multiplied by the
number of speakers
Example 2:
What wattage of input must be applied to the speakers of a sound reinforcement system
in, for example, a gymnasium or auditorium?
Step 1
Suppose that the noise level at the audience seats is 60 dB. If the required sound
pressure difference is 6 dB, the required sound pressure will be, by adding a peak factor
of 20 dB:
Required sound pressure = Noise level + Peak factor + Required sound pressure
Difference
= 86dB.
Step 2
Even the rearmost row of seats must have a sound pressure of 86 dB. Because it is 14
meters away from the speakers, the original sound pressure will be attenuated by 23 dB.
= 86dB + 23dB
= 109dB.
Step 3
As shown, a speaker sound pressure of 109 dB is necessary. Because two speakers are
used here, the required sound pressure per speaker is 109 dB minus 3 dB, that is, 106
dB.
Step 4
Next is the selection of a speaker model. Here, the WS-3200N was selected. The WS-
3200N has excellent directivity and provides satisfactory performance for music as well.
The output sound pressure of the WS-3200N is 95dB.
= 106dB - 95dB
= 11dB.
This can be obtained by applying a 13-watt input. The selection of the WS-3200N is
correct because its rated input is 15 watts.
Sound insulation and transmission have two meanings. One is to shutting out the
sounds or announcements that originate in the next room, and the other is to transmit
sounds or announcements through a door, for example.
Example 1:
= 54.5 dB.
Under this condition, the sound from the speaker is louder than the noise level at the
listening point, and can be heard through the door.
Transmission Losses
The human ear is sensitive to sounds of 2,000 Hz to 6,000 Hz. In other words, one of
the conditions for good audibility is to produce aloud sounds of 2,000Hz to 6,000Hz.
Each building or room has its own reverberation time frequency characteristic, which
means the reverberation time characteristic of that building or room against sounds
from low to high.
Generally, gymnasiums and auditoriums have such a structure and interior materials
that bass sound can hardly be absorbed. That is, bass sound lingers on and thus is
emphasized.
A graphic equalizer for sound field correction electrically corrects this phenomenon.
The graphic equalizer can vary sound level at every certain frequency. If the power
response is as shown in Fig. 2, the graphic equalizer suppresses the sounds of up to
1,000 Hz, and slightly raises treble sounds of 2,000 Hz and upward.
Speakers can be roughly classified into indoor and outdoor types, which can be further
broken down by place of use and purpose of use as shown in the table below.
a) Public address
b) Generally, a frequency band of about 200 to 6,000 Hz can achieve the purpose. In
the worst case, the required frequency band is from about 250 to 4,000 Hz, which
corresponds to the voice frequency band of man.
c) Background music
d) Background music, including music in a light sense of the word, requires a
frequency band of about 100 to 8,000 Hz.
e) Music
In a hall primarily designed for amplifying music, a frequency band of about 40 to 5,000
Hz is necessary.
Therefore, conditions for music reproduction are stricter than in the other cases, and
special care must be taken in selecting speakers for it.
Speaker arrangement varies with the electrical input to be applied and speaker
efficiency as mentioned before. Where speakers are used indoors, the purpose of use,
acoustic characteristics (reverberation, echo, and sound insulation), and speaker
directivity must also be taken into account. Where speakers are used outdoors, weather
resistance to winds and rains must be additionally considered.
Generally, there are three types of speaker arrangement normally applied in sound
system design:-
It also has disadvantages: Difficulty of providing a uniform level; poor clarity caused by
reverberation and echo; and large output power required where noise level is high. In
factories where much noise is produced, the dispersed system mentioned next is
suitable.
If many speakers of the system interfere with one another, it can lower sound quality.
The important point for the dispersed system is to correctly select a number of speakers
and the operating range of each speaker.
The dispersed system costs more to install than the centralized system.
This is a combination of the centralized system and the dispersed system. It uses
centralized speakers to achieve the intended sound pressure and small powered
auxiliary speakers in a dispersed arrangement at points where sound pressure is short
of the required level. The composite speaker system is frequently seen in auditoriums
and gymnasiums.
a) Restaurants, Offices, Stores because the ceiling is generally low, install many
ceiling mount speakers of about 1 W to 3W. Determine a number of speakers
suitable to the room size.
The following table applies where noise level is 60 dB, the peak factor 10 dB, and
the required sound pressure difference 6 dB.
Select 1-to 6-watt wall mount speakers suitable to the room size.
The following table applies where noise level is 60 dB, the peak factor 10 dB, and the
required sound pressure difference 6 dB.
Do not install the wall mount speaker facing each other. If wall mount speakers are
installed facing with each other the sound clarity will be degraded.
Select 15-W or 30-W 2-way column speakers suitable to the room size
Install the speakers about 4 meters to the front side on the stage, from where the
microphone is located. Select a number of speakers and their model from Table (A)
where the speakers are intended for music; or from Table (B) where they are mainly for
speeches.
There must be a difference of 20dB or more between the peak sound pressure and
noise.
If noise level exceeds 100 dB, the speaker sound cannot be distinguished from the
noise even if the volume is raised above the level.
If noise level is about 100 dB, install a horn speaker of about 5 to 10 watts near each
listener.
i) Factory premises
If speaker sound (sound within a vertical dispersion range of 60°) directly hits the
building opposite the speaker, its reflected sound adversely affects clarity. Install the
speakers so that the upper limit of the vertical dispersion range will be at the ground
level of the opposite building.
f) Mosques, etc.
If sound pressure is not enough with a single speaker, combine plural speakers
vertically to provide directivity.
Where speaker sound must reach far and wide, speaker output power
must be somewhat greater than normal because the effects of winds, topography,
temperature difference, and noise variations cannot be ignored.
After determining speaker arrangement and the required input to each speaker, the
total required input (wattage) can be calculated, and an amplifier that has an output
power corresponding to it can be selected. Select an amplifier on the basis of, not the
maximum output, but the rated output wattage. If additional speakers are planned to be
installed in the future, take this into account in selecting an amplifier wattage.
The number of input and output terminals, input and output impedances and levels
must also be studied. Performance wise, frequency response, signal-to-noise ratio, and
distortion factor also need to be examined. If the speakers are used exclusively for
music, the specifications must also be more strict than in other applications.
Too small an amplifier output cannot produce enough sound volume, whereas too great
an amplifier output can damage the speakers due to the excessive input applied to the
speakers. This problem is particularly true of low-impedance speakers.
a) High-impedance speakers
Because the amplifier output voltage is constant, the input power applied to the
speakers can be automatically determined from the input impedance of each speaker.
Example 1: WS-4000BN
The input impedance is 3.3 k ohms or 10 k ohms. If it is 3.3 k ohms where a 100- V
line is used,
If the amplifier with an output power of 30 watts is used, up to ten speakers can be
connected to it if the input impedance is 3.3 k ohms; or up to 30 speakers can be
connected to it if the input impedance is 10 k ohms. Since the output sound pressure of
the WS-4000BN is 92 dB, sound pressures of 97 dB and 92 dB can be produced
respectively. (Sound pressure increase by 3-watt input is 5 dB).Maximum numbers of
speakers to be connected to typical models are shown in the table below
Example 2:
What amplifier output wattage is necessary for the speakers connected as shown
below?
Calculate W1 to W6 for each speaker, and select an amplifier that has an output greater
than the calculated total.
The above condition is satisfied by an amplifier with a rated output of 30 watts. The WA-
320N or WA-730N, for example, may be selected. Remember not to select an amplifier
output by simply totaling the rated inputs of the speakers to be used. This method,
however, can end with the same result in some cases.
If low-impedance speakers are used, the amplifier delivers its full output power. Even in
this case, the following conditions must be met. Rated amplifier load impedance (ohms)
Example 1:
If the volume is raised in a connection as shown below, the 30-watt output of the
amplifier is fully applied to the speaker and damages the 15-watt speaker.
Example 2:
In a connection as shown below, only a 15-watt input is applied to the speaker because
the speaker impedance is double the amplifier impedance of 4 ohms.
The wrong use can cause poor tonal quality, lack of volume, or howling. It is important,
therefore, to fully explain the correct method of using the microphone to the user.
First, select a place of use, and a type of microphone suitable to the purpose of use. It
is necessary for this purpose to be fully familiar with the basic characteristics of the
microphone.
Generally, the range of frequencies audible to the human ear is about 20 to 18,000 Hz.
A microphone with the unnecessary portion of the bass range cut off can rather permit
amplification of clear sound with less "confinement" of sound.
Directivity means the sensitivity difference of a microphone in the direction of the sound
source, and can be generally classified into two kinds as follows:
This type of microphone is suited to use in cases in which only a selected sound is
required. Since it is resistant to howling when used in public address systems, it is
commonly used for a wide variety of purpose.
The output impedance of a microphone means the impedance of its terminal which is
connected to an amplifier. It is necessary to match the input impedance of the amplifier
with the output impedance of the microphone. Actually, however, a microphone may be
connected to an amplifier having impedance higher than the microphone output
impedance.
The noise induced in the microphone cable is amplified together with the voice signals
by the amplifier.
Therefore, all microphones use a shielded cable to prevent externally induced hum and
noise. The type which uses a two-conductor shielded cable is called the balanced type;
and that which uses a single-conductor shielded cable is called the unbalanced type.
The balanced type is recommended where the microphone is used far away from the
amplifier because it is less susceptible to externally induced noise and provides
constant tonal quality. In this case, however, the amplifier must have a balanced type
input terminal. Some unbalanced type microphones use a two-conductor shielded
cable. These microphones can be converted to the balanced type if its TS phone plug is
changed to a TRS phone plug or a XL-type connector.
The output stage of the HI-POWER AMP (and other amps as well) contains an output
transformer. This transformer is wired as follows.
Connect speakers so that the COMMON terminals are connected to (-), and the 4-ohm
terminal of the low-impedance speaker, or the 100-V or 70-V terminal of the high-
impedance speaker, is connected to (+) (low- and high-impedance terminals cannot be
used simultaneously, 100-V and 70-V lines cannot be used simultaneously). As the
rated load impedance of the 70-V line is half that of the 100-V line, twice the quantity of
speakers can be connected when the 70-V line is used (the speaker input, however, will
be half that for the 100-V line). For these reasons, the 70-V line is used in cases such
as BGM broadcasting in which a large number of speakers with relatively small input
rating are used.
Volume controller may be used only with high-impedance speakers. The wiring for the
volume controller is of either the 2- or 3-wire system. Volume control for each speaker is
possible with both the 2- and 3-wire systems. However, when it is OFF, emergency
announcement is impossible in case the 2-wire system is used; but possible in the 3-wire
system.
The user should be advised to note that the 2-and 3-wire volume controls are exactly the
same. As is obvious from the circuit diagram above, ALL terminal is normally connected
to COMMON. However, when the all-speaker switch is ON, it is connected to the 100-V
output of the output transformer. Since accurate attenuation is not obtained if the volume
controller is not suited to the impedance of the connected speaker, a volume controller
having the same wattage rating (or a wattage rating within the specified range) as the
speaker must be selected. A number of speakers can be connected and controlled
together by a volume controller within the specified rating.
a) Speaker Wiring
As wiring between the amp and speakers must be designed with consideration for
transmission losses, line loop resistance must be no more than 10% of the
combined impedance of the speakers or the rated load impedance of the amp.
For Example:
If the rated load impedance of the amp is 330 ohms and wiring is 1.0 mm in
diameter, what is the maximum length of the wiring?
The line resistance of annealed copper wire (single strand) is 22.9n/km (at 20°C). The
maximum length of wiring is calculated with the following equation:
AM radio antennas are always required. In strong broadcast areas, a 2- to 5-m vinyl-
covered wire should be attached to the wall or ceiling in a horizontal attitude and as
high as possible. Coaxial cable should be used between the antenna and a radio tuner.
NOTE: All sizes given may differ according to the sizes of the project.