Professional Documents
Culture Documents
VOLUME - V
AnAlysis of RAtes 238 s.R. 2022
ANNEXURE - A
X010A to X010H
Sl.
Specifications Unit
No.
Water treatment plant for the flow rate of 10000 LPH TO 85000 LPH
1 2 3
Design parameter- Supply installation and commissioning of the water treatment plant capable to treat the
water and make it potable at the flow rate of ............... LPH with suspended solids level less than 2000ppm,
and PH value and biological impurities beyond permissible limits of potable water parameters.
I COAGULENT DOSING SYSTEM No
Supply, Delivery, Installation and Commissioning of Agitator & Coagulant Dosing System for mld
with required accessories etc. complete for connecting to rising main and including the cost of vessel, stirrer,
storage tank and dosing system and also the cost of lead, lift and labour and maintenance of the equipments
during the defect liability period of 12 months and confirming to the following specifications and as directed
by Engineer - In- Charge:
Agitator
MOC of Flash mixer Tank and Storage FRP/HDPE
Capacity of Tank ……………………….
Diameter of mixing Tank ………………………….
Height of mixing Tank ………………………..
Stirrer with Gearbox and motor 1 No
MOC of stirrer and shaft SS 304
Coagulant dosing System
Type of dosing pump Mechanically actuated diaphragm type with drive
motor
MS Stand 1 no (To mount the dosing system)
Capacity of Dosing pump …………………..LPH
Polymer dosing System
Type of dosing pump Differential dosing system
Capacity of Tank …………….
Stirrer with Gearbox and motor 1 No
MOC of stirrer and shaft SS 304
MS Stand 1 no (To mount the dosing system)
Capacity of Dosing pump ……………….LPH
II STATIC MIXER FLOCCULATION TANK ( S.M.F.T ) No
Design, fabrication, supply, erection, testing and commissioning of Static Mixer Flocculation Tank
(SMFT) Circular shape made of Flocculator shaft and blades of MOC SS-304 & Flocculation Tank with
a Retention time of 20 Mints , with all accessories cost of all materials, machinery, labor, cutting, aligning,
anchoring, welding, finishing, cleaning required accessories with installation of S.M.F.T Complete with
connecting the MS platform between SMFT tank and Lamella Clarifier and confirming to the following
specifications Painting Work: Surface preparation with grit blasting with 50micron profile; For inside Two
coats of epoxy primer and two coats of non reactive epoxy coat , for Outside one coat of red oxide primer
and two coat of Enamel paint. Etc., Complete as directed by the Engineer in-Charge of work.
a) STATIC MIXER
MOC SS 304
Outer body of Static Mixer Mild Steel (IS 2062) with food grade epoxy paint
confirming IS 12643/1989.
b) FLOCCULATION TANK
AnAlysis of RAtes 239 s.R. 2022
MOC of SMFT Mild Steel (IS 2062) with food grade epoxy paint
confirming IS 12643/1989.
MOC of Flocculator shaft and blades Stainless Steel as per IS-304
Capacity of SMFT ……………..
wall thick ness 2 mm-12 mm as per structural calculation.
walk way cum Bridge On top of SMFT with ar- With 4” C Section and Chequered plate with sup-
rangement for mounting floculator. porting I .
III LAMELLA CLARIFIER No
Design, fabrication, supply, erection, testing and commissioning of Lamella Clarifier made of MOC
-M.S as per IS-2062 and grade BR with all accessories cost of all materials, machinery, labour, cutting,
aligning, anchoring, welding, finishing, cleaning required accessories and installation of Lamella using the
Crain on the pre constructed platform Etc., Complete with connecting the MS platform between SMFT tank
and Lamella Clarifier and confirming to the following specifications. Painting Work: Surface preparation
with grit blasting with 50 micron profile; For inside Two coats of epoxy primer and two coats of non reac-
tive epoxy coat , for Out side one coat of red oxide primer and two coat of Enamel paint. Etc., Complete
as directed by the Engineer in-Charge of work.
MOC of Lamella Clarifier Mild Steel (IS 2062) with food grade epoxy paint
confirming IS 12643/1989.
Type of settling Inclined Plate type
MOC of inclined plates FRP
Lengeth of lamellaplates 2400 mm
Arrangement of Lamella plates Single row with launder with launder on all four
sides, 1) raw water inlet launder, 2) Treated water
outlet launder 3) Two over flow launder for two
sides of lamella row.
Placing of lamella plates Arranged to place indivisualy with clerance to
remove plates for cleening one by one .
Stand to mount lamella Fabricated using C section of required sige and
length
Overflow of clarified water Adjestable plate to adjust the over flow levell
equal on both sides from lamella plate slots
Total no of lamellaplates ……………………………
Sludge storage and release Single Hopper bottom with opening in the bottom
flanged to fix butterfly valve and nessasary lenth
of pipe to relese the sludge to open drain.
walkway for Operation and meintenance 4” C section with chequgard plate of 4 mm thick
with width of 500mm Around the lamella
Ladder with raling to reach walkway on top of 2.5” x 2” L section with Round tube for raling
lamella
IV CLARIFIED WATER STORAGE TANK No
Providing, Supplying & Installation of Storage System (Ground Level Storage Reservoir) using GLASS
FUSED STEEL TANKS made of as per in compliance with AWWA D 103. GFS Tanks ( with sealant)
for intermediate balancing tank (filter feed tank) and confirming to the following specifications:
The Material of construction of walls, Tank Sheets is Glass fused to Steel with a enamel coating with a thick
ness of 2 to 12 mm as per the structural design with a tensile stregth of minimum 410 Mpa . The Doom roof
to be Corrugated Zincalume Roof, with 0.5 mm , AZ150 coating. and Load Bearing Capacity of 110 kg/
sqm with all accessory. The rate is inclusive of the cost of installation of tank.
AnAlysis of RAtes 240 s.R. 2022
TECHNICAL DATA:-
Dimension of Tank …………………….
MOC GFS Tanks ( with sealant)
ROOF TYPE Corrugated Zincalume roof.
FITTINGS & ACCESSORIES
Nozzles per tank As per requirment
TANK DESIGN PARAMETERS
Design Life 35+ Years
Tank Wall thickness - in compliance with AWWA
Design standard
D 103, Rest other material as per RSPL Standard.
TANK WALL
Type Bolted, Panelled, GLS Tanks
Shape Circular
MOC of Tank Sheets Glass fused to Steel
Thickness of wall sheets 2 mm-12 mm as per structural calculation.
2500/2800 mm X 1250 mm ( or as per Rostfrei
Sheet Dimensions ( Wall ) Design)
TANK ROOF
MOC of Roof Sheet Corrugated Zincalume Roof
Thickness of Roof Sheet 0.5 mm , AZ150 coating.
NOZZLES
MOC MS-HDG
Nozzle Schedule BS table 10D /E .
Nozzle Sizes and Quantity 100 mm , 2 no’s included. ( overflow and drain).
NUTS & BOLTS
MOC Hot Dipped Galvanized
TANK ACCESSORIES
External straight Cage Ladder including lockable
Ladder – Outside gate.
VI FILTRATION No
Providing of Multi-grade Pressure Filter with required accessories for connecting the filter to rising main
with a maximum / minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirm-
ing to the following specifications: to filter water containing 50 ppm of suspended solids to produce a
filtrate with less than 5 ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel confirming to IS 2062 fabricated of
Shell thickness ........... mm and dish end thickness.................mm the inner surface of M.S. Shell should
be provided with epoxy paint , the raw material confirming to FDA standards. Protective coat of red oxide
primer and enamel paint as per IS – 14209 for outer surface of the M.S. Shell should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribution and collection system.
ii. One initial charge of , filter media and under bed material with one set of suitable frontal pipe work
and valves and pressure gauges to monitor the pressure loss across the filter operated manually as per the
specifications below
c) The pressure filter unit is designed for the following specification:
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia ………………..mm
HOS 1875 mm
Frontal pipeline ……………. mm
Valves Butterfly valves
Air vent 1’’
Air Release Valve 1 no
Shell thickness ………... mm
Dish end thickness …………. mm
Filter media Silex Silica sand
Pressure relief valve 1 no 20 mm
Pressure gauge 2 nos
VII DISINFECTION No
Generation and dosing of ….. liter of hypochlorite per batch of 8 hours
Providing of Batch type Disinfectant system (Electro – Chlorinators / Chlorine Generators) with
required accessories for dosing the Sodium Hypochlorite solution suitable to control feed rate and the
Electro-chlorinator and dosing system confirming to the following specification. The system should gener-
ate the sodium hypochlorite solution on site utilizing comman salt, water and electric power and dose the
produced sodium hypochlorite solution at the rate of 2.0 ppm .
AnAlysis of RAtes
Water treatment plant for the flow rate of…................ with 16 hour pumping
10000 15000 20000 30000 45000 LPH 55000 65000 LPH 85000
Particulars LPH (0.16 LPH (.24 LPH (.32 LPH (.48 (.72 MLD) LPH (.88 (1.04 MLD) LPH (1.36
M.L.D) MLD) MLD) MLD) MLD) MLD)
I COAGULENT DOSING SYSTEM
Capacity of tank 300litres 300litres 300litres 300litres 300litres 300litres 300litres 300litres
Diameter of mixing tank 895 mm 895 mm 895 mm 895 mm 1080 mm 1080 mm 1080 mm 1080 mm
Height of mixing tank 940 mm 940 mm 940 mm 940 mm 1205 mm 1205 mm 1205 mm 1205 mm
Capacity of Dosing pump 10LPH 10LPH 10LPH 10LPH 10LPH 10LPH 10LPH 10LPH
Polymer Dosing
Capacity of Tank 500 liters 500 liters 500 liters 500 liters 1000 liters 1000 liters 1000 liters 1000 liters
Capacity of Dosing pump 10LPH 10LPH 10LPH 30LPH 40LPH 40LPH 40LPH 50LPH
II STATIC MIXER FLOCCULATION TANK ( S.M.F.T )
243
Capacity of SMFT vessel 3000Ltr 5000Ltr 6000Ltr 9000Ltr 15000ltrs 15000ltrs 19000ltrs 24000ltrs
III LAMELLA CLARIFIER
Total no of lamella plates 7 No 7 No 11 No 11 No 17 No 23 No 23 No 32 no
s.R. 2022
Dish end thickness 4mm 4mm 4mm 5mm 5mm 6mm 6mm 6mm
VII DISINFECTION
200 grams 200 grams 400grams/ 400grams/ 800grams/ 800grams/ 1200grams/ 1600grams/
/ Batch (8 / Batch (8 Batch (8 Batch (8 Batch (8 Batch (8 Batch (8 Batch (8
AnAlysis of RAtes
Generation capacity hours) hours) hours) hours) hours) hours) hours) hours)
Input cable
1.5sq.3core 1.5sq.3core 2.5sq.3core 2.5sq.3core 4sq.3core 4sq.3core 6sq.3core 6sq.3core
ISI MARKED
Output cable (multi strand
10sq.mm 10sq.mm 16sq.mm 16sq.mm 25sq.mm 25sq.mm 35sq.mm 50sq.mm
ISI Marked)
Naocl process tank 40 lit 40 lit 80ltrs 80ltrs 150ltrs 150ltrs 230ltrs 300ltrs
Naocl storage tank 40 lit 40 lit 80ltrs 80ltrs 150ltrs 150ltrs 230ltrs 300ltrs
135mm x 135mm x 250mm x 250mm x 325mm x 325mm x 365mm x 375mm x
Length and dia of cathode
54mm 54mm 47mm 47mm 54mm 54mm 67mm 80mm
135mm x 135mm x 135mm x 135mm x 135mm x 135mm x 135mm x 135mm x
Length and dia of anode
26mm 26mm 19mm 19mm 26mm 26mm 39mm 52mm
110mm x 110mm x 110mm x 110mm x 130mm x 130mm x 130mm x 140mm x
Siege of base plate of
85mm x 85mm x 85mm x 85mm x 100mm x 100mm x 100mm x 110mm x
Electrode
4mm 4mm 5mm 5mm 6mm 6mm 6mm 6mm
Dosing Pump 6 lph 6 lph 10 lph 10 lph 40 lph 40 lph 40 lph 40 lph
244
Note: Aerators, flash mixer, civil foundations, pump room, chemical house and other neccassry civil works have to consider extra as per
capacity and requirement apart from the SR price.
s.R. 2022
AnAlysis of RAtes 245 s.R. 2022
X010A 10000 0.16 2,73,125.00 6,82,812.50 8,84,925.00 3,63,090 74,290.00 2,51,275.00 1,26,183.75
X010B 15000 0.24 2,73,125.00 8,57,612.50 8,84,925.00 3,63,090 1,11,435.00 2,51,275.00 1,26,183.75
X010C 20000 0.32 2,73,125.00 10,37,875.00 12,69,485.00 5,18,700 1,11,435.00 2,99,250.00 1,89,002.50
X010D 30000 0.48 2,73,125.00 12,07,212.50 12,69,485.00 5,18,700 1,85,725.00 3,65,750.00 1,89,002.50
X010E 45000 0.72 3,22,287.50 15,24,037.50 13,83,105.00 7,08,225 1,85,725.00 5,27,250.00 3,02,622.50
X010F 55000 0.88 3,22,287.50 15,24,037.50 19,15,152.50 7,08,225 2,73,125.00 6,17,500.00 3,02,622.50
X010G 65000 1.04 3,22,287.50 18,24,475.00 19,15,152.50 11,70,400 4,33,722.50 6,98,250.00 3,78,005.00
X010H 85000 1.36 3,22,287.50 19,55,575.00 20,37,512.50 12,56,280 4,33,722.50 8,88,250.00 4,20,612.50
AnAlysis of RAtes 246 s.R. 2022
ANNEXURE - B
X020A to X020N
Sl.
Specifications Unit
No.
Water treatment plant for the flow rate of from 110000 LPH to 450000 LPH
1 2 3
Design parameter- Supply installation and commissioning of the water treatment plant capable
to treat the water and make it potable at the flow rate of ................. LPH with suspended solids
level less than 2000ppm, and PH value and biological impurities beyond permissible limits of
potable water parameters.
I COAGULENT DOSING SYSTEM No
Supply, Delivery, Installation and Commissioning of Agitator & Coagulant Dosing System for
....... mld with required accessories etc. complete for connecting to rising main and including the
cost of vessel, stirrer, storage tank and dosing system and also the cost of lead, lift and labour and
maintenance of the equipments during the defect liability period of 12 months and confirming to
the following specifications and as directed by Engineer - In- Charge:
Agitator
MOC of Flash mixer Vessel and Storage FRP/HDPE
Capacity of Tank ……………………….
Diameter of mixing Tank ………………………….
Height of mixing Tank ………………………..
Stirrer with Gearbox and motor 1 No
MOC of stirrer and shaft SS 304
Coagulant dosing System
Type of dosing pump Mechanically actuated diaphragm type with drive
motor
MS Stand 1 no (To mount the dosing system)
Capacity of Dosing pump …………….LPH
Polymer dosing System
Type of dosing pump Differential dosing system
Capacity of Tank …………….
Stirrer with Gearbox and motor 1 No
MOC of stirrer and shaft SS 304
MS Stand 1 no (To mount the dosing system)
Capacity of Dosing pump ………………LPH
II STATIC MIXER FLOCCULATION TANK ( S.M.F.T ) No
Design, fabrication, supply, erection, testing and commissioning of Static Mixer Flocculation Tank
(SMFT) Circular shape made of Flocculator shaft and blades of MOC SS-304 & Flocculation Tank
made of MOC -Glass fused to Steel 2 mm-12 mm as per structural calculation. with a Retention
time of 20 Minutes , with all accessories cost of all materials, machinery, labor, cutting, aligning,
anchoring, welding, finishing, cleaning required accessories with installation of S.M.F.T Complete
with connecting the MS platform between SMFT tank and Lamella Clarifier and confirming to the
following specifications . Complete as directed by the Engineer in-Charge of work.
a) STATIC MIXER
MOC SS 304
Outer body of Static Mixer Mild steel confirming to IS 2062 with epoxy paint
for inner surface and enamel on outer surface.
AnAlysis of RAtes 247 s.R. 2022
b) FLOCCULATION TANK
MOC of SMFT Glass fused to Steel penal ( with sealant).The
Material of construction of walls, Tank Sheets is
Glass fused to Steel with a enamel coating with
a thickness of 2 to 12 mm as per the structural
design with a tensile strength of minimum 410
MPA .
MOC of Flocculator shaft and blades Stainless Steel as per IS-304
Capacity of SMFT vessel …………………………….
wall thickness 2 mm-12 mm as per structural calculation.
walk way cum Bridge On top of SMFT with With 4” or 6” C Section as per structural
arrangement for mounting flocculator. calculation and Chalked plate with required
support of I section .
III LAMELLA CLARIFIER No
Design, fabrication, supply, erection, testing and commissioning of Lamella Clarifier made of
MOC -M.S as per IS-2062 and grade BR with all accessories cost of all materials, machinery,
labour, cutting, aligning, anchoring, welding, finishing, cleaning required accessories and
installation of Lamella using the Crain on the pre constructed platform Etc., Complete with
connecting the MS platform between SMFT tank and Lamella Clarifier and confirming to the
following specifications. Painting Work: Surface preparation with grit blasting with 50 micron
profile; For inside Two coats of epoxy primer and two coats of non reactive epoxy coat , for
Outside one coat of red oxide primer and two coat of Enamel paint. Etc., Complete as directed
by the Engineer in-Charge of work.
MOC of Lamella Clarifier Mild Steel (IS 2062) with food grade epoxy paint
confirming IS 12643/1989.
Type of settling Inclined Plate type
MOC of inclined plates FRP
Length of lamella plates 2400 mm
Arrangement of Lamella plates Single row with launder with launder on all four
sides, 1) raw water inlet launder, 2) Treated water
outlet launder 3) Two over flow launder for two
sides of lamella row.
Placing of lamella plates Arranged to place individually with clearance to
remove plates for cleaning one by one.
Stand to mount lamella Fabricated using C section of required size and
length
Overflow of clarified water Adjustable plate to adjust the over flow level
equal on both sides from lamella plate slots
Sludge storage and release Single Hopper bottom with opening in the bottom
flanged to fix butterfly valve and necessary length
of pipe to release the sludge to open drain.
walkway for Operation and maintenance 4” C section with chequgaurd plate of 4 mm thick
with width of 500mm Around the lamella
Ladder with railing to reach walkway on 2.5” x 2” L section with Round tube for railing
top of lamella
AnAlysis of RAtes 248 s.R. 2022
Providing, Supplying & Installation of Three Phase open well submersible pump set (1+1
) of approved make as filter feed pump with required accessories etc. complete: fuses and fuse
box, starter and panel board, ELCB, MCB, electrical cables from board to motor, piping for
suction and delivery and for connection to the filter unit and rubber sheet support for pump and Set
confirming to the following specifications: of
V Head 20 m Two
Flow rate ……………… Unit
Starter and Panel Board 1 Set
ELCB, MCB 1 set
Pipe size for inlet and outlet ……………….
VI FILTRATION No
Providing of Multi-grade Pressure Filter with required accessories for connecting the filter to
rising main with a maximum / minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2
respectively and confirming to the following specifications: to filter water containing 50 ppm of
suspended solids to produce a filtrate with less than 5 ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel confirming to IS 2062
fabricated of shell thickness ………... mm and dish end thickness ………... mm the inner
surface of M.S. Shell should be provided with epoxy paint , the raw material confirming to FDA
standards. Protective coat of red oxide primer and enamel paint as per IS – 14209 for outer
surface of the M.S. Shell should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribution and collection system.
ii. One initial charge of , filter media and under bed material with one set of suitable frontal
pipe work and valves and pressure gauges to monitor the pressure loss across the filter operated
manually as per the specifications below
c) The pressure filter unit is designed for the following specification:
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia ………………..mm
HOS 1875 mm
Frontal pipeline ……………. Mm
Valves Butterfly valves
No off valves 5
Air vent 1’’
Air Release valve 1 no
Shell thickness ………... mm
Dish end thickness …………. Mm
Filter media Silex Silica sand
Pressure relief valve 1 no 20 mm
Pressure gauge 2 no’s
MOC of vessel MS IS 2062 with Epoxy food grade inside
AnAlysis of RAtes 250 s.R. 2022
VII DISINFECTION No
a) Providing of Disinfectant system (continuous Electro – Chlorinators) with required
accessories for controlled dosing of Sodium Hypochlorite solution suitable to the water flow.
The Electro-chlorinator and dosing system confirming to the following specification. The system
should be designed to generate the sodium hypochlorite solution automatically by drawing
required common salt from salt chamber, water from storage and electric power and dose the
sodium hypochlorite solution at the rate of 2.0 ppm .
AnAlysis of RAtes
Water treatment plant for the flow rate of… ...................with 16 hour pumping
1,10,000 LPH 135000 LPH 150000LPH 185000 LPH 200000 LPH 225000 LPH
Particulars
(1.76 M.L.D) (2.16 MLD) (2.04 MLD) (2.96 MLD) (3.20 MLD) (3.60 MLD)
1 2 3 4 5 6 7 8
I COAGULENT DOSING SYSTEM
Capacity of Tank 300 liters 500 liters 500 liters 500 liters 500 liters 500 liters
Diameter of mixing 1327 mm 1327 mm 1327 mm 1327 mm 1475mm 1475mm
Tank
Height of mixing 1245 mm 1245 mm 1245 mm 1245 mm 1987mm 1987mm
Tank
Capacity of Dosing
30LPH 30LPH 30LPH 30LPH 30LPH 30LPH
pump coagulant
Polymer Dosing
Polymer dosing 1500 liters 2000 liters 2000 liters 2000 liters 3000liters 3000liters
251
tank capacity
Capacity of Dosing 100LPH 100LPH 100LPH 200LPH 200LPH 200LPH
pump Flocculent
II STATIC MIXER FLOCCULATION TANK ( S.M.F.T )
Capacity of SMFT 35000Ltr 45000Ltr 50000ltrs 60000ltrs 65000ltr 75000ltr
vessel
III LAMELLA CLARIFIER
Total no of lamella 41 No 59 no 59 no 82no 82no 82no
plates
IV CLARIFIED WATER STORAGE TANK
Dimension of tank 6870 x 2450 mm 77300 x 2450 77300 x 2450 8590 x 2450mm 7730 x 8590 x 3650mm
mm mm 3650mm
V Three Phase open well submersible pump set
s.R. 2022
Flow rate 1,10,000 lph 135000lph 150000lph 185000lph 200000lph 225000lph
VI FILTRATION
Filter vessel dia 2200 mm 2400mm 2600mm 2800mm 3000mm 3200mm
Frontal pipeline 150 mm 150 mm 150 mm 200mm 200mm 250mm
AnAlysis of RAtes
Shell thickness 6 mm 6 mm 6 mm 6 mm 6 mm 8 mm
Dish end thickness 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm
VII DISINFECTION
specification 200gms 300gms 300gms 400gms 400gms 500gms
Input voltage 230V AC 1Phase 230V AC 230V AC 415V AC 3Phase 415V AC 415V AC 3Phase
50Hz 1Phase 50Hz 1Phase 50Hz 50Hz 3Phase 50Hz 50Hz
Output voltage 24V DC 24V DC 24V DC 30V DC 30V DC 35V DC
Output current 40A 60A. 60A. 90A 90A 125A
max.
Output current 50A 75A 75A 150A 150A 200A
design
Input cable 2.5sq.3core 2.5sq.3core 2.5sq.3core 4sq.4core 4sq.4core 6sq.4core
ISI MARKED
Output cable (multi 10sq.mm 16sq.mm 16sq.mm 25sq.mm 25sq.mm 35sq.mm
252
strand ISI Marked)
Metering pump 40 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH
Flow meter 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH
Naocl generation
500mm x 500mm x 700mm x 700mm x
module (Electrode) 300mm x 110mm 800mm x 110mm
110mm 110mm 110mm 110mm
dimension
Brine tank 1000 lit 1000 lit 1000 lit 1000 lit 1000 lit 1000 lit
Dosing Pump 40LPH 100LPH 100 LPH 200LPH 200LPH 200 LPH
Aerators, flash mixer, civil foundations, pump room, chemical house and other necessary civil works have to consider
extra as per capacity and requirement apart from the SR price.
s.R. 2022
X020G to X020N Dimensions
Sl.
Specifications
No. X020G X020H X020I X020J X020K X020L X020M X020N
AnAlysis of RAtes
Water treatment plant for the flow rate of… ....................... with 16 hour pumping
250000 300000 325000 350000 375000 LPH 400000 425000 LPH 450000
Particulars LPH (4.00 LPH (4.80 LPH (5.20 LPH (5.60 (6.00 MLD) LPH (6.40 (6.80 MLD) LPH (7.20
MLD) MLD) MLD) MLD) MLD) MLD)
1 2 3 4 5 6 7 8 9 10
I COAGULENT DOSING SYSTEM
Capacity of Tank 1000ltrs 1000ltrs 1000ltrs 1000ltrs 1000ltrs 1000ltrs 1000ltrs 1000ltrs
Diameter of mixing Tank 1475 mm 1475 mm 1475 mm 1475 mm 1475 mm 1475 mm 1475 mm 1475 mm
Height of mixing Tank 1987 mm 1987 mm 1987 mm 1987 mm 1987 mm 1987 mm 1987 mm 1987 mm
Capacity of Dosing pump coagu-
40LPH 40LPH 40LPH 40LPH 40LPH 50LPH 50LPH 50LPH
lant
Polymer Dosing
Capacity of Tank 3500 liters 3500 liters 3500 liters 3500 liters 3500 liters 3500 liters 3500 liters 3500 liters
Capacity of Dosing pump Floc- 200LPH 200LPH 200LPH 300LPH 300LPH 300LPH 300LPH 300LPH
253
culent
II STATIC MIXER FLOCCULATION TANK ( S.M.F.T )
Capacity of SMFT vessel 75000 ltr 100000ltrs 110000ltrs 120000ltrs 13000ltrs 135000 ltr 140000 ltr 150000 ltr
III LAMELLA CLARIFIER
Total no of lamella plates 118no 118no 148no 148no 148no 178no 178no 178no
IV CLARIFIED WATER STORAGE TANK
8590 x 94500 x 10310 x 10310 x 11170 x 11170 x 11170 x 11170 x
Dimension of tank 3650mm 3650mm 3650mm 3650mm 3650mm 3650mm 3650mm 3650mm
V Three Phase open well submersible pump set
Flow rate 250000lph 300000lph 325000lph 350000lph 375000lph 400000lph 425000lph 450000lph
VI FILTRATION
Filter vessel dia 2400mm 2600mm 2600mm 2800mm 2800mm 3000mm 3000mm 3200mm
Frontal pipeline 150 mm 150 mm 150 mm 200mm 200mm 200mm 200mm 200mm
s.R. 2022
Shell thickness 6 mm 6 mm 6 mm 6 mm 6 mm 6 mm 6 mm 8 mm
Dish end thickness 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 10 mm
VII DISINFECTION
specification 500gms 600gms 700gms 700gms 800gms 800gms 900gms 900gms
Input voltage 415V AC 415V AC 415V AC 415V AC 415V AC 415V AC 415V AC 415V AC
AnAlysis of RAtes
3Phase 3Phase 50Hz 3Phase 50Hz 3Phase 50Hz 3Phase 50Hz 3Phase 3Phase 50Hz 3Phase
50Hz 50Hz 50Hz
Output voltage 35V DC 35V DC 40V DC 40V DC 50VDC 50VDC 50V DC 50V DC
Output current max. 125A 150A 150A 150A 150A 150A 175A 175A
Output current design 200A 250A 250A 250A 250A 250A 300A 300A
Input cable 6sq.4core 6sq.3core 6sq.3core 6sq.3core 8sq. 4core 8sq. 4core 8sq. 4core 8sq. 4core
ISI MARKED
Output cable (multi strand ISI 35sq.mm 50sq.mm 75sq.mm 75sq.mm 75sq.mm 75sq.mm 75sq.mm 75sq.mm
Marked)
Metering pump 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH
Flow meter 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH 100 LPH
Naocl generation module dimen- 800mm x 880mm x 960mm x 1000mm x 1000mm x 1000mm x 1000mm x 1000mm x
sion 110mm 110mm 150mm 150mm 150mm 150mm 150mm 150mm
254
Brine tank 1000 lit 1000 lit 1001 lit 1002 lit 1003 lit 1004 lit 1003 lit 1004 lit
Dosing Pump 200 lph 300 lph 300lph 300 lph 300 lph 300 lph 400 lph 400 lph
s.R. 2022
RATES OF WTP FROM X020A TO X020N
STATIC CLARI-
COAGU- Three
MIXER FIED
LENT LAMELLA Phaseopenwell
AnAlysis of RAtes
FLOCCULA- WATER FILTRATION DISINFECTION
DOSING CLARIFIER submersible
TION TANK STORAGE
SYSTEM pump set (1+1 )
( S.M.F.T ) TANK
SL.NO LPH MLD I II III IV V VI VII
X020A 110000 1.76 3,65,987.50 24,08,962.50 25,91,410.00 16,42,550 5,42,972.50 10,68,750.00 6,30,372.50
X020B 135000 2.16 4,26,075.00 26,65,700.00 43,37,225.00 20,77,555 6,80,627.50 12,35,000.00 7,35,252.50
X020C 150000 2.40 4,26,075.00 30,15,300.00 43,37,225.00 20,77,555 7,93,155.00 13,77,500.00 7,35,252.50
X020D 185000 2.96 4,26,075.00 32,61,112.50 54,18,800.00 24,95,650 9,06,775.00 16,33,287.50 7,35,252.50
X020E 200000 3.20 4,42,462.50 32,61,112.50 54,18,800.00 26,80,425 11,34,015.00 17,69,850.00 8,41,225.00
X020F 225000 3.60 4,53,387.50 33,06,997.50 54,18,800.00 33,23,100 11,34,015.00 20,10,200.00 8,41,225.00
X020G 250000 4.00 4,64,312.50 33,06,997.50 86,74,450.00 33,23,100 14,19,157.50 26,11,075.00 10,50,985.00
255
X020H 300000 4.80 7,31,975.00 53,31,400.00 86,74,450.00 36,48,000 16,55,137.50 28,90,755.00 12,61,837.50
X020I 325000 5.20 7,31,975.00 60,30,600.00 86,74,450.00 43,46,250 16,55,137.50 28,90,755.00 14,31,175.00
X020J 350000 5.60 7,31,975.00 60,30,600.00 1,08,37,600.00 43,46,250 18,92,210.00 32,66,575.00 14,31,175.00
X020K 375000 6.00 7,31,975.00 60,30,600.00 1,08,37,600.00 51,01,500 18,92,210.00 32,66,575.00 15,96,142.50
X020L 400000 6.40 9,06,775.00 65,22,225.00 1,08,37,600.00 51,01,500 21,28,190.00 35,39,700.00 15,96,142.50
X020M 425000 6.80 9,06,775.00 65,22,225.00 1,08,37,600.00 51,01,500 21,28,190.00 35,39,700.00 17,65,480.00
X020N 450000 7.20 9,06,775.00 66,13,995.00 1,08,37,600.00 51,01,500 23,64,170.00 40,20,400.00 17,65,480.00
s.R. 2022
AnAlysis of RAtes 256 s.R. 2022
ANNEXURE - C
Sl. No. Specifications Unit Price
Automatic Online Hydraulically Operated Self Cleaning Multi grade
X050A Pressure Filter for the flow rate of 10000 & 15000 LPH (0.16 &0.24
M.L.D) with 16 hour pumping
1 2 3 4
Automatic hydraulic self cleaning screen filter(400 Microns)
MATERIALS OF CONSTRUCTION
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for con-
necting the filter to rising main with a maximum / minimum operating pressure
of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to the following
specifications: to filter water containing 50ppm of suspended solids to produce
a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel confirm-
ing to IS 2062 fabricated of plate thickness 4mm and dish end thickness 5mm
the inner surface of M.S. Shell should be provided with epoxy paint, the raw
material confirming to FDA standards. Protective coat of red oxide primer and
enamel paint as per IS – 14209 for outer surface of the M.S. Shell should be
provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribution
and collection system.
ii. One initial charge of , filter media and under bed material with one set of
suitable frontal pipe work and valves and pressure gauges to monitor the pres-
sure loss across the filter operated manually as per the specifications below
1NO 299250
c) The pressure filter unit is designed for the following specification:
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia (Anthra- 1000 mm
cite/Carbon)
HOS 1875 mm
Frontal pipeline 80 mm
Valves Butterfly valves
Shell thickness 4 mm
Dish end thickness 5 mm
Pressure relief valve 1 no
a Anthracite, Carbon
CHEMICAL COMPO- VALUES
SITION
Carbon Content 92.00%
Sulphur 0.60%
Hardness 4 Moles
Total 883500
AnAlysis of RAtes 259 s.R. 2022
1 2 3 4
Automatic hydraulic self cleaning screen filter(400 Microns)
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to
the following specifications: to filter water containing 50ppm of suspended
solids to produce a filtrate with less than 5 ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 5mm and dish end thick-
ness 6mm the inner surface of M.S. Shell should be provided with epoxy
paint , the raw material confirming to FDA standards. Protective coat of red
oxide primer and enamel paint as per IS – 14209 for outer surface of the
M.S. Shell should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribu-
tion and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the
pressure loss across the filter operated manually as per the specifications
below
c) The pressure filter unit is designed for the following specification:
1NO 365750
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia (Anthra- 1200 mm
cite/Carbon)
HOS 1875 mm
Frontal pipeline 75 mm
A Anthracite, Carbon
CHEMICAL COMPO- VALUES
SITION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
Bulk Volume 1.37m³ m/t
1130lit 241537.5
Bulk Density 700 kg/m³
Total 1020537.5
AnAlysis of RAtes 262 s.R. 2022
Seals EPDM
AnAlysis of RAtes 263 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to
the following specifications: to filter water containing 50ppm of suspended
solids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 5mm and dish end thick-
ness 6mm the inner surface of M.S. Shell should be provided with epoxy
paint, the raw material confirming to FDA standards. Protective coat of red
oxide primer and enamel paint as per IS – 14209 for outer surface of the
M.S. Shell should be provided.
b) The following accessories should be provided with the pressure
filter:
i. One suitable set of laterals and header and bell mouth for water distribu-
tion and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the
pressure loss across the filter operated manually as per the specifications
1NO 527250
below
c) The pressure filter unit is designed for the following specification:
A Anthracite, Carbon
CHEMICAL COMPO- VALUES
SITION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
1540lit 329175
Bulk Volume 1.37m³ m/t
Bulk Density 700 kg/m³
Density/Specific gravity 1.40-1.45 kg/dm³
Grain Porosity <10%
Hardness 4 Moles
Crush resistance Hardgrave Index 38
Attrition Loss 0.06%
Loss on ignition 97-95%
Total 1269675
AnAlysis of RAtes 265 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to the
following specifications: to filter water containing 50ppm of suspended sol-
ids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 6mm and dish end thickness
8mm the inner surface of M.S. Shell should be provided with epoxy paint,
the raw material confirming to FDA standards. Protective coat of red oxide
primer and enamel paint as per IS – 14209 for outer surface of the M.S.
Shell should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribu-
tion and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the
pressure loss across the filter operated manually as per the specifications
below
c) The pressure filter unit is designed for the following specification: 1NO 617500
A Anthracite, Carbon
Total 1458250
AnAlysis of RAtes 268 s.R. 2022
Self‐Cleaning Mecha-
Suction Scanner Cleaning Mechanism
nism
Recommended differen-
tial pressure to initiate 0.5 bar
flushing cycle 1No 413250
Waste Water Per Cycle
28
(lit)
Flushing Cycle Time
10
(Sec)
CONTROL AND ELECTRICITY
Control power supply 4 x AA type 1.5V batteries
Solenoid 9‐12 VDC latching solenoid
MATERIALS OF CONSTRUCTION
Filter housing RPA (Reinforced Polyamide)
Cleaning Mechanism PBT (polybutylene)
Seals EPDM
AnAlysis of RAtes 269 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to
the following specifications: to filter water containing 50ppm of suspended
solids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 6mm and dish end thick-
ness 8mm the inner surface of M.S. Shell should be provided with epoxy
paint, the raw material confirming to FDA standards. Protective coat of red
oxide primer and enamel paint as per IS – 14209 for outer surface of the
M.S. Shell should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribu-
tion and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the
pressure loss across the filter operated manually as per the specifications
below
c) The pressure filter unit is designed for the following specification: 1NO 698250
a Anthracite, Carbon
1 2 3 4
Automatic hydraulic self cleaning screen filter(400 Microns)
Mounting Type ONLINE
Design Flow/Filter 65 cum/h
Net Filtration Area/Filter 2400 sq.cm
Minimum flow for flush-
65 cum/h
ing
Min. Req. Working Pres-
3.0 bar
sure
Design Pressure 8.0 bar
Self‐Cleaning Mecha-
Suction Scanner Cleaning Mechanism
nism
Recommended differen-
tial pressure to initiate 0.5 bar
flushing cycle
Waste Water Per Cycle 1No 413250
28
(lit)
Flushing Cycle Time
10
(Sec)
ContRol AnD eleCtRiCity
Control power supply 4 x AA type 1.5V batteries
Seals EPDM
AnAlysis of RAtes 272 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for con-
necting the filter to rising main with a maximum / minimum operating pres-
sure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to the fol-
lowing specifications: to filter water containing 50ppm of suspended solids to
produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 6mm and dish end thickness
8mm the inner surface of M.S. Shell should be provided with epoxy paint,
the raw material confirming to FDA standards. Protective coat of red oxide
primer and enamel paint as per IS – 14209 for outer surface of the M.S. Shell
should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribution
and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the 1NO 888250
pressure loss across the filter operated manually as per the specifications
below
c) The pressure filter unit is designed for the following specification:
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia (Anthra- 2000 mm
cite/Carbon)
HOS 1875 mm
Frontal pipeline 100 mm
Valves Butterfly valves
Shell thickness 6 mm
Dish end thickness 8 mm
Pressure relief valve 1 no
Pressure gauge 2 no’s
MOC of vessel MS IS 2062 with Epoxy food grade inside
Filter Media For Pressure Filter
AnAlysis of RAtes 273 s.R. 2022
A Anthracite, Carbon
CHEMICAL COMPO- VALUES
SITION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
Bulk Volume 1.37m³ m/t 3140lit 671175
Recommended differential
pressure to initiate flushing 0.5 bar
1No 413250
cycle
MATERIALS OF CONSTRUCTION
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to
the following specifications: to filter water containing 50ppm of suspended
solids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel confirming
to IS 2062 fabricated of plate thickness 6mm and dish end thickness 8mm
the inner surface of M.S. Shell should be provided with epoxy paint, the raw
material confirming to FDA standards. Protective coat of red oxide primer
and enamel paint as per IS – 14209 for outer surface of the M.S. Shell should
be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribution
and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the
pressure loss across the filter operated manually as per the specifications
below
c) The pressure filter unit is designed for the following specification: 1NO 1068750
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia (Anthracite/ 2200 mm
Carbon)
HOS 1875 mm
Frontal pipeline 150 mm
Valves Butterfly valves
Shell thickness 6 mm
Anthracite, Carbon
A
CHEMICAL VALUES
COMPOSITION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
Bulk Volume 1.37m³ m/t 3800lit 812250
Bulk Density 700 kg/m³
Density/Specific gravity 1.40-1.45 kg/dm³
Grain Porosity <10%
Hardness 4 Moles
Crush resistance Hardgrove Index 38
Total 2294250
AnAlysis of RAtes 277 s.R. 2022
1 2 3 4
Automatic hydraulic self cleaning screen filter(400 Microns)
Self‐Cleaning Mecha-
Suction Scanner Cleaning Mechanism
nism
Recommended differen-
tial pressure to initiate 0.5 bar
flushing cycle
1No 821750
Waste Water Per Cycle
125
(lit)
Flushing Cycle Time
15
(Sec)
CONTROL AND ELECTRICITY
Control power supply 4 x AA type 1.5V batteries
MATERIALS OF CONSTRUCTION
Filter housing Carbon steel
Seals EPDM
AnAlysis of RAtes 278 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operat-
ing pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirm-
ing to the following specifications: to filter water containing 50ppm of
suspended solids to produce a filtrate with less than 5ppm of suspended
solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 6mm and dish end thick-
ness 8mm the inner surface of M.S. Shell should be provided with epoxy
paint, the raw material confirming to FDA standards. Protective coat of
red oxide primer and enamel paint as per IS – 14209 for outer surface of
the M.S. Shell should be provided.
b) The following accessories should be provided with the pressure
filter:
i. One suitable set of laterals and header and bell mouth for water distri-
bution and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor
the pressure loss across the filter operated manually as per the specifica-
tions below
c) The pressure filter unit is designed for the following specification:
1NO
12,35,000.00
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Filter vessel dia (Anthra- 2400 mm
cite/Carbon)
HOS 1875 mm
Shell thickness 6 mm
Anthracite, Carbon
A
CHEMICAL COMPO- VALUES
SITION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
4500
Bulk Volume 1.37m³ m/t 961875
lit
Bulk Density 700 kg/m³
Density/Specific gravity 1.40-1.45 kg/dm³
Seals EPDM
AnAlysis of RAtes 281 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to the
following specifications: to filter water containing 50ppm of suspended sol-
ids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 6mm and dish end thickness
8mm the inner surface of M.S. Shell should be provided with epoxy paint,
the raw material confirming to FDA standards. Protective coat of red oxide
primer and enamel paint as per IS – 14209 for outer surface of the M.S.
Shell should be provided.
b) The following accessories should be provided with the pressure filter:
i. One suitable set of laterals and header and bell mouth for water distribu-
tion and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor the
pressure loss across the filter operated manually as per the specifications
below
c) The pressure filter unit is designed for the following specification:
1NO
1235000
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Shell thickness 6 mm
Anthracite, Carbon
a
CHEMICAL COMPOSITION VALUES
1 2 3 4
Automatic hydraulic self cleaning screen filter(400 Microns)
Seals EPDM
AnAlysis of RAtes 284 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required acces-
sories for connecting the filter to rising main with a maximum
/ minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2
respectively and confirming to the following specifications: to filter
water containing 50ppm of suspended solids to produce a filtrate
with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild
steel confirming to IS 2062 fabricated of plate thickness 6mm and
dish end thickness 8mm the inner surface of M.S. Shell should be
provided with epoxy paint, the raw material confirming to FDA
standards. Protective coat of red oxide primer and enamel paint as
per IS – 14209 for outer surface of the M.S. Shell should be pro-
vided.
b) The following accessories should be provided with the pres-
sure filter:
i. One suitable set of laterals and header and bell mouth for water
distribution and collection system.
ii. One initial charge of , filter media and under bed material
with one set of suitable frontal pipe work and valves and pressure
gauges to monitor the pressure loss across the filter operated manu-
ally as per the specifications below
c) The pressure filter unit is designed for the following specifi- 1NO
1377500
cation:
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Shell thickness 6 mm
a Anthracite, Carbon
CHEMICAL COMPOSI- VALUES
TION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
Bulk Volume 1.37m³ m/t 5300Kg 1132875
Total 3332125
AnAlysis of RAtes 286 s.R. 2022
Recommended differential
pressure to initiate flushing 0.5 bar
cycle 1No 1135250
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories
for connecting the filter to rising main with a maximum / minimum
operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and
confirming to the following specifications: to filter water containing
50ppm of suspended solids to produce a filtrate with less than 5ppm of
suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel
confirming to IS 2062 fabricated of plate thickness 5mm and dish end
thickness 6mm the inner surface of M.S. Shell should be provided with
epoxy paint, the raw material confirming to FDA standards. Protective
coat of red oxide primer and enamel paint as per IS – 14209 for outer
surface of the M.S. Shell should be provided.
b) The following accessories should be provided with the pressure
filter:
i. One suitable set of laterals and header and bell mouth for water dis-
tribution and collection system.
ii. One initial charge of , filter media and under bed material with one
set of suitable frontal pipe work and valves and pressure gauges to
monitor the pressure loss across the filter operated manually as per the
specifications below
c) The pressure filter unit is designed for the following specifica-
1NO
tion: 1705487
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Anthracite, Carbon
a
CHEMICAL COMPOSI- VALUES
TION
Carbon Content 92.00%
Moisture Content 2.00%
Ash Content 3.50%
Volatile Matter 5.50%
Sulphur 0.60%
6150Kg 1314563
Bulk Volume 1.37m³ m/t
Bulk Density 700 kg/m³
Density/Specific gravity 1.40-1.45 kg/dm³
Grain Porosity <10%
Hardness 4 Moles
Crush resistance Hardgrove Index 38
Attrition Loss 0.06%
Loss on ignition 97-95%
Total 4155300
AnAlysis of RAtes 289 s.R. 2022
Recommended differential
pressure to initiate flushing 0.5 bar
cycle 1NO 1135250
Seals EPDM
AnAlysis of RAtes 290 s.R. 2022
2 FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to
the following specifications: to filter water containing 50ppm of suspended
solids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 5mm and dish end thick-
ness 6mm the inner surface of M.S. Shell should be provided with epoxy
paint, the raw material confirming to FDA standards. Protective coat of red
oxide primer and enamel paint as per IS – 14209 for outer surface of the
M.S. Shell should be provided.
b) The following accessories should be provided with the pressure
filter:
i. One suitable set of laterals and header and bell mouth for water distribu-
tion and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor
the pressure loss across the filter operated manually as per the specifica-
tions below
c) The pressure filter unit is designed for the following specification:
1NO
1769850
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Shell thickness 6 mm
1 2 3 4
Automatic hydraulic self cleaning screen filter(400 Microns)
Mounting Type ONLINE
Self‐Cleaning Mecha-
Suction Scanner Cleaning Mechanism
nism
Recommended differen-
tial pressure to initiate 0.5 bar 1NO 1135250
flushing cycle
Waste Water Per Cycle
125
(lit)
Flushing Cycle Time
15
(Sec)
CONTROL AND ELECTRICITY
Control power supply 4 x AA type 1.5V batteries
Solenoid 9‐12 VDC latching solenoid
DP Switch Integral Sensors
MATERIALS OF CONSTRUCTION
Filter housing Carbon steel
Cleaning Mechanism PBT (polybutylene)
Seals EPDM
AnAlysis of RAtes 293 s.R. 2022
FILTRATION
Providing of Multi-grade Pressure Filter with required accessories for
connecting the filter to rising main with a maximum / minimum operating
pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively and confirming to
the following specifications: to filter water containing 50ppm of suspend-
ed solids to produce a filtrate with less than 5ppm of suspended solids.
a) The vertical cylindrical shell with dish ends made up of mild steel con-
firming to IS 2062 fabricated of plate thickness 5mm and dish end thick-
ness 6mm the inner surface of M.S. Shell should be provided with epoxy
paint, the raw material confirming to FDA standards. Protective coat of
red oxide primer and enamel paint as per IS – 14209 for outer surface of
the M.S. Shell should be provided.
b) The following accessories should be provided with the pressure
filter:
i. One suitable set of laterals and header and bell mouth for water distri-
bution and collection system.
ii. One initial charge of , filter media and under bed material with one set
of suitable frontal pipe work and valves and pressure gauges to monitor
the pressure loss across the filter operated manually as per the specifica-
tions below
c) The pressure filter unit is designed for the following specification:
1NO
2010200
Working pressure 1.5 Kg / Cm2 to 3.5 Kg / cm2
Shell thickness 6 mm
a Anthracite, Carbon
AnAlysis of RAtes 294 s.R. 2022
Hardness 4 Moles
Crush resistance Hardgrove Index 38
Attrition Loss 0.06%
Loss on ignition 97-95%
Total 4641700
AnAlysis of RAtes 295 s.R. 2022
ANNEXURE - D
GLASS FUSED STEEL TANK FOR CLARIFIED WATER STORAGE & TREATED WATER
STORAGE
X060 Description
1 CLARIFIED WATER STORAGE TANK
Providing, Supplying & Installation of Storage System (Ground Level Storage Reservoir) using
GLASS FUSED STEEL TANKS made of as per in compliance with AWWA D 103. GFS Tanks (
with sealant) for intermediate balancing tank (filter feed tank) and confirming to the following speci-
fications:
The Material of construction of walls, Tank Sheets is Glass fused to Steel with a enamel coating with
a thickness of 2 to 12 mm as per the structural design with a tensile strength of minimum 410mpa . The
Doom roof to be Corrugated Zinc alum Roof, with 0.5 mm , AZ150 coating. and Load Bearing Capac-
ity of 110 kg/ sqm with all accessory. The rate is inclusive of the cost of installation of tank.
TECHNICAL DATA:-
MOC GFS Tanks ( with sealant)
ROOF TYPE Corrugated Zinc alum roof.
FITTINGS & ACCESSORIES
Nozzles per tank As per requirement
TANK DESIGN PARAMETERS
Design Life 35+ Years
Tank Wall thickness - in compliance with AWWA D 103, Rest other
Design standard
material as per RSPL Standard.
TANK WALL
Type Bolted, Paneled, GLS Tanks
Shape Circular
MOC of Tank Sheets Glass fused to Steel
Thickness of wall sheets 2 mm-12 mm as per structural calculation.
Sheet Dimensions ( Wall ) 2500/2800 mm X 1250 mm ( or as per Rostra Design)
TANK ROOF
MOC of Roof Sheet Corrugated Zinc alum Roof
Thickness of Roof Sheet 0.5 mm, AZ150 coating.
NOZZLES
MOC MS-HDG
Nozzle Schedule BS table 10D /E.
Nozzle Sizes and Quantity 100 mm, 2 no’s included. (Overflow and drain).
NUTS & BOLTS
MOC Hot Dipped Galvanized
TANK ACCESSORIES
Ladder - Outside External straight Cage Ladder including lockable gate.
Internal Ladder Nylon Rope Ladder with Aluminum steps.
Air vent Turbine Vent (SS-304),
AnAlysis of RAtes 296 s.R. 2022
ANNEXURE - E
X080
Flow
Capacity (MLD) ClO2 for disinfection (1496 & HCL ClO2 for algae removal (1496 & HCL
rate
16hrs pumping Both) Both)
(LPH)
1499 QTY HCL QTY Rs. (INR)/ 1496 QTY HCL QTY Rs. (INR)/
(Kg) (Kg) year (Kg) (Kg) Quarter
10000 0.16 122.64 122.64 53041.8 68.544 68.544 19763.52
15000 0.24 183.96 183.96 79562.7 102.816 102.816 29645.28
20000 0.32 245.28 245.28 106083.6 137.088 137.088 39527.04
30000 0.48 367.92 367.92 159125.4 205.632 205.632 59290.56
45000 0.72 551.88 551.88 238688.1 308.448 308.448 88935.84
55000 0.88 674.52 674.52 291729.9 376.992 376.992 108699.36
65000 1.04 797.16 797.16 344771.7 445.536 445.536 128462.88
85000 1.36 1042.44 1042.44 450855.3 582.624 582.624 167989.92
110000 1.76 1349.04 1349.04 583459.8 753.984 753.984 217398.72
135000 2.16 1655.64 1655.64 716064.3 925.344 925.344 266807.52
150000 2.4 1839.6 1839.6 795627 1028.16 1028.16 296452.8
185000 2.96 2268.84 2268.84 981273.3 1268.064 1268.064 365625.12
200000 3.2 2452.8 2452.8 1060836 1370.88 1370.88 395270.4
225000 3.6 2759.4 2759.4 1193440.5 1542.24 1542.24 444679.2
250000 4 3066 3066 1326045 1713.6 1713.6 494088
300000 4.8 3679.2 3679.2 1591254 2056.32 2056.32 592905.6
325000 5.2 3985.8 3985.8 1723858.5 2227.68 2227.68 642314.4
350000 5.6 4292.4 4292.4 1856463 2399.04 2399.04 691723.2
375000 6 4599 4599 1989067.5 2570.4 2570.4 741132
400000 6.4 4905.6 4905.6 2121672 2741.76 2741.76 790540.8
425000 6.8 5212.2 5212.2 2254276.5 2913.12 2913.12 839949.6
450000 7.2 5518.8 5518.8 2386881 3084.48 3084.48 889358.4
Note: While estimating add the Generator price and Chemical as per the capacity and as per the application and con-
sider the necessary civil works and pipe modification
AnAlysis of RAtes 297 s.R. 2022
ANNEXURE - F
25LPH WATER PURIFICATION PLANTS
Sl. No Description Qty
1 Skid with cabin 1 No’s
2 Housing 3 No’s
6 Diverter 1 No’s
10 Membrane 2 No’s
A Materials
Raw Water N/A
1
Pump
Micron Micron cartridge filter for removing Suspended particles >10
Cartridge Filter &5 micron. Should have capacity of 100 litters /hour. Material
2 3 No’s
of Cartridge should be polypropylene having length of 10” X 4”
dia, Inc of GAC or CTO.
High Pressure Pump Side
Pump Rated Motor: 24VDC,2.5A,(150 GP)
3 Flow Rate:2.5 LPM 1 No
Inlet Pressure: 15-90 PSI
Adapter: 24 vdc,2A
RO Membrane For Capacity of 25 litters / hour Spiral wound TFC Polyamide
4 suitable size Dia 2.5” x 10” long. No of membrane Shall have 2 2 No’s
numbers and the No of membrane housing shall be 2.
RO Housing For Capacity of 100 liters / hour Spiral wound TFC Polyamide
5 suitable size Dia 2.5” x 10” long. The No of membrane housing 2No’s
shall be 2.
Skid Skid rectangular type for capacity of 25 LPH – 1no with above
6 1 No
mentioned items mounted on it. With cabin.
Instrumentation Low Pressure Switch(24v) for raw water protections at inlet
items should be provided.3/8” Solenoid Valve of range (with Brass
made 0-10bar) 24 volt DC should be provided for high pressure
pump for low pressure cutoff /Stainless steel float switch
with suitable cable for proper operation of the system. smps
7 1set
5a, Function-to measure pressure Pump outlet, Filter outlet,
Pressure pump
• Pressure controller valve
*inc Elbows and Fittings
.
Post- carbon To remove chlorine, iodine, odor, bad taste and color etc of
8 1 No
Coconut shell/Charcoal based size 10” long x 2.5” dia
Installation &
9 Each
Commissioning
AnAlysis of RAtes 299 s.R. 2022
4 Membrane 4 No’s
5 Pump 48 V 2 No’s
20 Diverter 1 No’s
21 LPS 1 No’s
Post- carbon To remove chlorine, iodine, odour, bad taste and color etc of
10 1 No
Coconut shell/Charcoal based size 10” long x 2.5” dia
Installation &
1Unit
Commissioning
AnAlysis of RAtes 301 s.R. 2022
Sl.
Description Specification Qty
No
Control Panel with Panel Dimension Shouldbe minimum 450mm (W) x 250 (H) mm
Data Transfer to x 450 (D) mm. Sheet thicknesses should be 1.6 & 2mm finished
Server with powered coated RAL 7035. It has to operate with both Auto
/ manual. Float switch for raw water tank has to be connected in
this to avoid dry run. Analog Voltmeter and Ammeter should be
19 1 No’s
there for metering. Electrical protection like Phase Reverse, UV,
OV, Phase Fail, Neutral Fail, Asymmetry, and Over Current (OLR)
are mandatory. Phase indication lamp for single phase PUMP ON/
OFF, Pump trip, Supply Unhealthy, Float Switch fault. Raw water
Pump & High pressure Pump Control Should be inside this panel.
Instrumentation Low Pressure Switch(24v) for raw water protections at inlet should
items be provided.3/8” Solenyed Valve of range (with Brass made 0-
10bar) 24 volt DC should be provided for high pressure pump for
low pressure cutoff /Stainless steel float switch with suitable cable
for proper operation of the system. smps 5a, Function-to measure
20 pressure Pump outlet, Filter outlet, Pressure pump 1set
• 3/8” 24 volt DC PVC Auto flush system with solenoid valve
• Pressure controller valve
• 1/4”-3/8” TDS controller
For backup the instrumentation 230V as input and 24v DC,5A
output switch mode power supply unit should be provided.
P0st- carbon To remove chlorine, iodine, odour, bad taste and color etc of
21 1 No
Coconut shell/Charcoal based size 10” long x 2.5” dia
Mineral filter To remove acidic waste in the body, supplies minerals. Improves
PH & taste of water etc of antibacterial balls(mineral Ceramic,
22 alkaline, antibacterial, tourmaline, taste enhancer, oxygen reduction 1Set
potential and silver activated carbon balls size 10” long x 2.5” dia
UV set 11 w UV tube with stainless steel housing size 8” long with inlet
23 outlet dia 1/4” to 3/8” Function-to disinfect water, will kill bacteria 1 set
and micro-organisms up to 99.9%
UF Membrane For Capacity of 100 liters / hour Spiral wound Polypropylene
24 suitable size Dia 2.5” x 10” long . No of membrane Shall have 2 1 No
numbers and the No of membrane housing shall be 2.
12v DC TDS
25 1 No
controller
Installation &
26 Each
Commissioning
AnAlysis of RAtes 304 s.R. 2022
19 LPS 1 No’s
Pump Side
Rated Motor: 24VDC,2.5A,(100 GPD)
5 3 No’s
High Pressure Pump Flow Rate:2.5 LPM
pump output:82+_8 Psi
Sl.
Description Specification Qty
No
Raw Water
1 N/A
Pump
Micron cartridge filter for removing Suspended particles >10 &5 micron.
2 Should have capacity of 100 liters /hour. Material of Cartridge should be 3 No’s
Micron Car- polypropylene having length of 20” X 4” dia, Inc of GAC or CTO.
3 tridge Filter Inc of 20” GAC or CTO 1 No’s
4 20”Micron Cartridge filter 2 No’s
Anti Scalant
Transparent glassy balls of size 16.5mm to 17.5mm dia, weight approxi-
5 Dosing System 8
mately 9 to 11gm and should have the PH of 6.5 to 7.5
& Chemicals
Pump Side
Rated Motor: 24VDC,2.5A,(100 GPD)
6 High Pressure 4 No’s
Flow Rate:2.5 LPM
Pump pump output:82+_8 Psi
7 Adaptor :24 VDC, 2.5 A 4 No’s
For Capacity of 45 liters / hour Spiral wound TFC Polyamide suitable size
8 RO Membrane Dia 3” x 12” long. No of membrane Shall have 2 numbers and the No of 4 No’s
membrane housing shall be 2.
For Capacity of 100 liters / hour Spiral wound TFC Polyamide suitable
9 RO Housing 4 No’s
size Dia 3 x 10” long. The No of membrane housing shall be 2.
Skid rectangular type for capacity of 150 LPH – 1no with above men-
10 Skid 1 No
tioned items mounted on it. With cabin.
Low Pressure Switch(24v) for raw water protections at inlet should be
provided.3/8” Solenyed Valve of range (with Brass made 0-10bar) 24 volt
DC should be provided for high pressure pump for low pressure cutoff /
Stainless steel float switch with suitable cable for proper operation of the
Instrumentation
11 system. smps 5a, Function-to measure pressure Pump outlet, Filter outlet, 1set
items
Pressure pump
• Pressure controller valve
*inc Elbows , tubes and Fittings
*Flow meter.
To remove chlorine, iodine, odour, bad taste and color etc of Coconut
12 Post- carbon 1 No
shell/Charcoal based size 10” long x 2.5” dia
Installation &
14 1Unit
Commissioning
AnAlysis of RAtes 308 s.R. 2022
12 Carbon 15 kg
Instrumentation &Controls
A Pressure Gauges Function-to measure pressure
41 Quantity 2 No
42 Pump outlet, Filter outlet, High Pressure pump
Location
43 Discharge and RO Reject
44 Range 0-7 Kg/cm2
45 Location Feed pump outlet /Filter outlet
46 Quantity 2 No
47 Location High pressure pump discharge and RO reject
48 Range 0-20 Kg/ cm2
MOC SS
B Flow Indicator Function-to measure flow rate at location
Quantity 3 No.
49 Location RO Feed, RO Product, Reject
50 Type Float type, panel mounted
51 Max, operating 40 degree centigrade
52 Temperature
53 Measuring points RO Feed, RO Product, Reject
AnAlysis of RAtes 312 s.R. 2022
Sl.
Description Specification Qty
No
Raw Water Storage Tank Function–storage of raw water
1 with low level and high
level switch.
Type/ MOC Three Layered HDPE tanks made from virgin material of Food 1
Grade Quality, suitable for the purpose of Storage of drinking
/portable water. (Where source fluctuation persists or space
constraint exists underground sump may be provided).
Control Provision of Low Level and High Level Switch 2
Capacity 5000 Liter tank
2 Inlet Pump Function– to feed water from storage tank to filter
Type Horizontal Centrifugal
Number One
Make Grundfos /Mahindra /Nuton/Kirloskar /Crompton greaves/
equivalent to these make 1 No’s
MOC SS -304
Capacity As per plant requirement (2.5m3 per hour) as per new
specification
Pressure and power As per plant requirement (3kg / sq cm, 1 HP)
3 Sand filter with MPV Pressure sand Filter (PSF) to remove any Turbidity in water
Flow Rate As per plant requirement
Material of Housing ss-304
Size As per plant requirement (10”x54”) 1
Media Pebbles, Gravel, Coarse Sand , Fine Sand & Anthracite of
Suitable Quantity as per plant Requirement
MOC of housing SS
Gradual Activated Function– to remove pesticide, insecticide and biological
Carbon Filter with min impurities from water.
4
900 Iodine value with
auto MPV 1
Flow Rate As per plant requirement
MOC of housing SS -304
Size As per plant requirement (10”X54”)
AnAlysis of RAtes 314 s.R. 2022
Micron Cartridge Filter Function- fine filtration of water for removal of Suspended
5 solids up to 1 micron size to prevent chocking/ blockage of UF
Membrane (if necessary)
Flow rate As per plant requirement 4m3/hrs
MOC of Cartridge FRP/Engineering grade plastic/equivalent
housing 2
NO. of Cartridge As per plant requirement 2 No’s
housing
Micron Rating 5 Micron & 1 Micron
Flow velocity 2.5 m/Sec
MOC of cartridge PP
Anti scalant Dosing Function- to inhibit scaling of hardness salt and Silica on RO
6
System membranes
Pump 1 Set
Quantity 1 No.
Type Electronic/Diaphragm Type 1
Capacity 0-6LPH
Quantity of tank 1 No.
Capacity of Tank 100 liter.
MOC of tank SS -304
High Pressure Pump & Function-to develop required pressure for Reverse Osmosis on
7
motor RO Membranes
Type Vertical Centrifugal Multistage 2.5 m3/hr flow 10-13 bar
pressure
Pump External jacket, chrome-nickel steel 1.4301 EN 10088 (ASI 304)
suction casing, delivery
a). casing, impeller, lower
cover, Upper cover,
Spacer sleeve.
pump shaft, plug chrome-nickel steel 1.4301 EN 10088 (ASI 303) 1
mechanical seal, Ceramic alumina/ carbon/EPDM
SO 3069-KU
Wear ring PTFE
O-ring NBR
MOC of pump casing SS316 / SS 304
motor IS 12615:2014, IEC 60034/30, Rating IE3 with IP 65 protection
b).
and class F insulation
Capacity As per plant requirement
Pressure and power As per plant requirement
AnAlysis of RAtes 315 s.R. 2022