Professional Documents
Culture Documents
Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 1 3: 44 G M T+00: 00 2006, U n con trol l ed Copy, (c) BSI
BS ISO
65 5 0 -1 : 1 994
Incorp orating
Road vehicles —
Sheath-typ e glow-plugs
housing —
Part 1 : M1 4 × 1 ,2 5 glow-plugs
IC S 43 . 06 0. 5 0
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
BS AU 262-1 :1 995
Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 1 3: 44 G M T+00: 00 2006, U n con trol l ed Copy, (c) BSI
C ommittee MC E /9 , Ignition equip ment for s park ignition engines, upon which
into effe ct on
1 5 D ece mb er 1 9 95
© BS I 2 0 D ec emb e r 2 00 2
s tandard:
C o mmittee referenc e MC E /9
ISBN 0 5 80 2494 1 7
BS AU 262-1 :1 995
Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 1 3: 44 G M T+00: 00 2006, U n con trol l ed Copy, (c) BSI
C ontents
Page
National foreword ii
1 S cop e 1
2 Normative references 1
i
© BS I 2 0 D ec emb er 2 0 02
BS AU 262-1 :1 995
Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 1 3: 44 G M T+00: 00 2006, U n con trol l ed Copy, (c) BSI
National foreword
conical s eating and their cylinder head housing — Part 1 : M1 4 × 1 , 25 glow - p lugs ,
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 3 and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.
1 Scope
This part of ISO 6550 specifies the main characteristics of M1 4 × 1 , 25 sheath-type glow- plugs with conical
seating and their cylinder head housing, for use with diesel (compression-ignition) engines.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of
this part of ISO 6550. At the time of publication, the editions indicated were valid. All standards are subj ect
to revision, and parties to agreements based on this part of ISO 6550 are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.
ISO 1 91 9: 1 988 , Road v ehicles — M1 4 × 1 , 25 sp ark- p lugs w ith flat seating and t heir cylinder head ho us ings.
ISO 8092-1 : —, Ro ad v ehicles — Connectio ns for on- b oard electric harness es — Part 1 : Single- pole co nnector
1)
tab s — Dim ensio ns and sp ecific req uirem ents .
3.1 Glow-plugs
The dimensions and tolerances of the cylinder head housing for sheath- type glow- plugs are given in
Figure 2.
The threads of M1 4 × 1 , 25 glow- plugs and the corresponding tapped holes in the cylinder head shall
conform to the threads specified for M1 4 × 1 , 25 spark- plugs in ISO 1 91 9.
The installation torque values shall be as given in Table 1 . The values apply to new sheath- type glow- plugs
without lubricant on the threads. If threads are lubricated, the torque value shall be reduced by
approximately one- third to avoid overstressing.
1)
To be published. (Revision of ISO 8092- 1 : 1 989)
2 0 to 35 4
NO TE E ngine manufacturers may specify different torques for the first glow- plug installation.
1)
D iffering specifications ap ply to the admissible tightening torque according to the nut used.
BS AU 262-1 :1 995
3
BS AU 262-1 :
Li cen sed Copy: Lon d on Sou th Ban k U n i versi ty, Lon d on Sou th Ban k U n i versi ty, Sat Dec 09 02: 1 3: 44 G M T+00: 00 2006, U n con trol l ed Copy, (c) BSI
1 995
BS ISO 65 5 0-1 : BSI — British Standards Institution
1 994
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: orders@bsi-global.com. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: copyright@bsi-global.com.
W4 4AL