Professional Documents
Culture Documents
CRM9250N
Toolplus User
Manual
S/N: XXXX CS
Version: XX
Release Date: XXX
1/28
CRM9250N ToolPlus User Manual
History
Version Date Page Description Participants
Write by:
V1.0 May, 2016 All Create Check by:
Approve by:
Write by: Hanfeng Xiao
1. Add folder download description
V1.1 March, 2019 Check by:
2. Add English image
Approve by:
Content
History............................................................................................................................................................................ I
Content..........................................................................................................................................................................II
1. Overview................................................................................................................................................................ 3
2. Range of Application............................................................................................................................................ 4
3. PC Configuration..................................................................................................................................................5
4. Terms and Definition............................................................................................................................................ 6
5. Description of Related Files................................................................................................................................. 7
6. Driver Installation.................................................................................................................................................8
7. Login and Authorization Access........................................................................................................................ 11
7.1. Login............................................................................................................................................................. 11
7.2. Communication Checking............................................................................................................................ 11
7.3. Access Unit Dispensing Authorization.........................................................................................................12
8. Description of Test Function..............................................................................................................................14
8.1. ToolPlus Page Description............................................................................................................................14
8.2. Unit status..................................................................................................................................................... 15
8.3. Transaction Command..................................................................................................................................17
8.3.1. Page Description...................................................................................................................................18
8.3.2. Recommend Process.............................................................................................................................19
8.3.3. Command Description..........................................................................................................................20
8.4. Maintenance Command................................................................................................................................22
8.4.1. Motor Test.............................................................................................................................................22
8.4.2. Solenoid Test.........................................................................................................................................23
8.4.3. Cassette Configuration......................................................................................................................... 24
8.4.4. Get Sensor Value...................................................................................................................................26
8.5. Online Download..........................................................................................................................................27
8.5.1. Page Description...................................................................................................................................27
8.5.2. Preparation............................................................................................................................................28
8.5.3. Single File Download........................................................................................................................... 29
8.5.4. CE/NV Folder Download..................................................................................................................... 33
9. Menu Operation..................................................................................................................................................36
9.1. Connect USB................................................................................................................................................ 36
9.2. Read Unit Log...............................................................................................................................................38
9.3. Configure Currency Information..................................................................................................................39
9.4. Error Code Check......................................................................................................................................... 41
9.5. Option Configuration....................................................................................................................................42
Appendix 1 Unit Status Information Correspondence Table.................................................................................43
Appendix 2 Unit Sensor Status Information Correspondence Table.................................................................... 46
1. Overview
This document explains the function and instructions of CRM9250N, which is helpful for engineer to conduct
daily maintenance or function test. Meanwhile, related training could also refer to this document.
2. Range of Application
Testers
Technical engineers
R&D personnel
3. PC Configuration
Install Dunite 1.2 SR2withSP7 or version above;
Minimum hardware configuration: PIII800, 256MB memory, keyboard, mouse, USB2.0 interface.
6. Driver Installation
Before first time using, you need to install Dunite (Dunite1.2SR2b82-Run.exe or version above) and USB driver
(GRGUSBDriver_v2.0.10.3.exe or version above).
After installed GRGUSBDriver_v2.0.10.3.exe, connect the USB interface from CRM9250N to PC. If it is the first
time connection, it will prompt new hardware discovered.
7.2.Communication Checking
If prompt information as shown below after login, means the USB cable between PC and main control board is
not connected or not well connected.
8.2.Unit status
CRM9250N sensor page is as shown below.
8.3.Transaction Command
Choose “ActionCmd” and show page as shown below:
Power on initialize: Execute initialize setting, get cassette information and initial setting in turn;
Initial setting: Set CRM9250N working mode parameter. If there are no special requirements, could use the
default parameter. Attention that the parameter change must complete in file 4(CRM9250NInitSet.ini);
Get cassette information: Get CRM9250Ncassette information;
Initialize: Initialize CRM9250N unit, check if each module is in normal state, clear the channel from NE to
NF;
Open shutter: Open NF shutter;
Close shutter: Close NF shutter;
Prepare dispense: Put NF baffle t proper position, use this interface before dispensing;
Dispense: Feed specified quantity notes from cassette, after NV verification, send valid notes to NF output
slot, invalid notes to NE;
Present: Check if there are notes at NF, and push baffle t proper position, use this interface after dispensing;
Prepare deposit: Put NF baffle at proper position, use this interface before cash counting;
Cash count: Close shutter, verify the notes at input slot by NV, the valid notes send to NE and invalid notes
send back to output slot, responding frame will show the received notes detail such as denomination, and the
counting command frame parameter could change verification mode (genuine notes/test notes); 0x00:
genuine notes mode, means unit could reject fake notes according to verification result; 0xFF: test notes
mode, means unit will not reject fake notes, but only reject notes not meet structure requirements (such as
over tilt, small gap, connected notes, etc.); 0x0F: simulated notes mode, unit will receive or reject simulate
notes according to verification result;
Deposit: CRM9250N store notes in NE, and the responding frame will show the notes detail information
such as amount. The deposit command frame parameter could change. 0x00: Verification mode (genuine
notes/test notes), also could be call as genuine notes mode, means unit save notes into responding cassette
according to verification result; 0xFF: Test notes mode, unit will save valid notes to cassette with highest
priority and invalid notes to AC; 0x0F: Simulate notes mode, unit will save simulate notes into responding
cassette according to verification result. RC priority: Each cassette could set 4 different level as 1-4, 1 is
highest and 4 is lowest; if there are 2 cassettes with same level, the smaller slot No. cassette is the higher one.
For example, RC1 and RC2 are all L2, then the priority of RC1 is higher than RC2. We suggest that the 4
cassettes have different priority in principle;
Cancel deposit: CRM9250N reject the notes in NE to the output slot;
Prepare next transaction: CRM9250N clear internal data and prepare for the next transaction;
Retract NF: Verify notes at NF and then send to corresponding cassette, the retract NF command parameter
could change, the retract terminal: 0x0A: retract all notes to LRB; 0x0B: retract all notes to AC; 0x0C: retract
notes according to specified cassettes priority;
Retract NE: CRM9250N store the notes in NE to AC cassette, the retract NE command parameter could
change, the retract terminal: 0x0B means AC and 0x0C means RC;
Get machine status: Get status of each module and sensor;
8.4.Maintenance Command
8.4.1. Motor Test
CRM9250N configuration including the following sections: denomination, version, setting, etc.
1 Denomination: Denomination including 3 parts: country code where using the cassette, notes denomination
and notes version. The 3 part information could be chosen in the down-drop menu, choose order is: country
code, denomination, then version.
2 Version: There are 2 choices for version: do not distinguish version and distinguish version. Do not
distinguish version: means the cassette will save all version of specified denomination notes. Distinguish
version: means the cassette will save specified version of specified denomination notes;
3 Cassette setting: There are 4 choices for cassette setting: recycle, dispense only, deposit only, sorting.
Recycle: means the cassette can both deposit and dispensing. Dispense only: means the cassette can only
dispensing but not deposit. Deposit only: means the cassette can only deposit but not dispensing. Sorting:
using to deposit the sorting notes during sorting. Make sure if the unit support sorting function or not before
setting, if the unit does not support the function, the setting is invalid.
Cassette configuration page is as shown below:
8.5.Online Download
8.5.1. Page Description
8.5.2. Preparation
1) Download CE folder
1 Click “Browser” and prompt page as below, chooses folder need to download ;
3 Start download;
2) Download NV folder
1 Click “Browser” and prompt page as below, chooses folder need to download ;
3 Start download;
9. Menu Operation
9.1.Connect USB
2 Turn on CRM9250N;
3 Start CRM9250N toolplus (double click or right click CRM9250Test.exe), the toolplus start up and
beep once means the toolplus is well connected with CRM9250N main control board;
4 After start toolplus, you can control USB by click the “Setting” in menu bar, as shown below:
Communication interface: Click “Communication interface”, click “Connect” on the prompt page and
Click “Tools” in menu bar, in the prompt submenu, click “Option” to enter page to get unit debug
information (unit Log information), as shown below. Choose “Auto Get Log Info” in part 1 and toolplus
will get unit log automatically after each transaction command, engineer could find the log folder in the
CRM9250N “Configure currency” menu is as shown below: click “Tools” in setting, choose “Set
Machine Support Note” in the prompt menu to enter currency configure page;
Click “Set Machine Support Note” and prompt unit currency configuration page, as shown below. Before
runningCRM9250N should complete the initial setting, and the unit support currency in the initial setting
Part 3: Click “Add All” to add all NV support currency to CRM9250N support currency;
Part 4: Choose one currency in Part 1, click “Add One” to add the NV support currency to CRM9250N
support currency;
Part 5: Click “Delete All” to delete all CRM9250N support currency in Part 2;
Part 6: Click “Delete One” to delete one CRM9250N support currency in Part 2;
Part 7: Click “Get” to get CRM9250N notes verification module (NV) support currency and show in Part
1;
Click “Help”, choose “Error Code Check” in prompt menu and shown as below:
Input the error code or warning code want to query in Part 1, then click “Query”, the corresponding code
9.5.Option Configuration
Click “Tools” and choose “Option” in the prompt submenu, and prompt dialog as shown below. Option
configuration has 3 choices: type, auto get log info, auto get OCR; choose corresponding configuration
25 Full 1: LR full
3rd byte
24 Reserved Reserved
23 Reserved Reserved
22 Lower unit is pull out/push in 1: The lower unit is pull out or push in
21 Lower unit in correct position 1: The lower unit is in correct position
20 Lower cover channel open 1: Channel is open
27 Full 1: means AC is full
26 Almost full 1: means AC is almost full
25 Cassette info 1: means fail to read AC information
24 Deposit only Empty 1: means AC is empty
4th byte 23 Abnormal 1: means AC is in abnormal state
cassette (AC)
Separate roller
22 1: means AC separate roller is error
error
Notes push board
21 1: means AC notes push board is error
error
20 Cassette exist 1: means AC is exist
27
26
25
24 Reserved Reserved
10th byte 23
22
21
1: means there is cassette being
20 Cassette plugging plugging, read the cassette information
and the bit will be 0
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
23 Reserved Reserved
13th byte
24 Reserved Reserved
25 Reserved Reserved
26 RC1En 0: Block 1: Not block
27 RC2En 0: Block 1: Not block
20 ACEn 0: Block 1: Not block
21 ATCEn 0: Block 1: Not block
22 Reserved Reserved
23 SD01 0: Block 1: Not block
14th byte
24 SD02 0: Block 1: Not block
25 SD03 0: Block 1: Not block
26 SD04 0: Block 1: Not block
27 SD05 0: Block 1: Not block
20 SD06 0: Block 1: Not block
21 SD07 0: Block 1: Not block
22 SD08 0: Block 1: Not block
23 SD09 0: Block 1: Not block
15th byte
24 SD10 0: Block 1: Not block
25 Reserved Reserved
26 UD01 0: Block 1: Not block
27 UD02 0: Block 1: Not block
20 UD03 0: Block 1: Not block
21 UD04 0: Block 1: Not block
22 Reserved Reserved
23 Reserved Reserved
16th byte
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
17th byte 23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21
Reserved Reserved
22 Reserved Reserved
18th byte
23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
19th byte 23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21
Reserved Reserved
22 Reserved Reserved
20th byte 23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
21st byte 23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
22nd 23 Reserved Reserved
byte 24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
23rd byte 23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21
Reserved Reserved
24 byte
th 22 Reserved Reserved
23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved
20 Reserved Reserved
21 Reserved Reserved
22 Reserved Reserved
25th byte 23 Reserved Reserved
24 Reserved Reserved
25 Reserved Reserved
26 Reserved Reserved
27 Reserved Reserved