Professional Documents
Culture Documents
Table of Contents
Cover Page 1
Title Page 2
Warnings and Errors: 3
Input Echo: 4
XY Coordinate Calculations: 7
Element Original Thicknesses: 8
Internal Pressure Calculations: 9
External Pressure Calculations: 13
Element and Detail Weights: 16
Center of Gravity Calculation: 17
MDMT Summary: 18
Vessel Design Summary: 19
Cover Page PV Elite® 2019
DESIGN CALCULATION
Note:
PV Elite performs all calculations internally in Imperial Units
to remain compliant with the ASME Code and any built in assumptions
in the ASME Code formulas. The finalized results are reflected to show
the user's set of selected units.
® SPLM Licensed User
PV Elite 2019
PV Elite 2019 SP1 Licensee:
FileName : C-962 Page 3 of 20
Warnings and Errors: Step: 0 12:17pm Oct 14,2022
Configuration Directives:
XY Coordinate Calculations:
The final thicknesses shown in the table below were changed for
one or more of the following reasons:
Tampo Plano
Note:
Post Weld Heat Treatment is required for this Element/Joint and it was
specified as being heat treated.
Carretel
Casco
= 64.455 kgf/cm²
Note: The knuckle radius r is less than 3 times the head thickness.
Please check UG-32(j) and UG-81 for Code compliance.
Minimum 9.332
Tampo Plano
Carretel
Casco
Note: The knuckle radius r is less than 3 times the head thickness.
Please check UG-32(j) and UG-81 for Code compliance.
Weight Summary:
Note:
The Corroded Weight and thickness are used in the Horizontal
Vessel Analysis (Ope Case) and Earthquake Load Calculations.
Surface
From To Area
cm²
10 20 ...
20 30 17109.9
30 40 102353
40 50 6097.64
Notes:
[ ! ] - This was an impact tested material.
[ 1] - Governing Nozzle Weld.
[ 4] - ANSI Flange MDMT Calcs; Thickness ratio per UCS-66(b)(1)(-c).
[ 5] - ANSI Flange MDMT Calcs; Thickness ratio per UCS-66(b)(1)(-b).
[ 6] - MDMT Calculations at the Shell/Head Joint.
[ 7] - MDMT Calculations for the Straight Flange.
[ 8] - Cylinder/Cone/Flange Junction MDMT.
[ 9] - Calculations in the Spherical Portion of the Head.
[10] - Calculations in the Knuckle Portion of the Head.
[11] - Calculated (Body Flange) Flange MDMT.
[12] - Calculated Flat Head MDMT per UCS-66.3
[13] - Tubesheet MDMT, shell side, if applicable
[14] - Tubesheet MDMT, tube side, if applicable
[15] - Nozzle Material
[16] - Shell or Head Material
[17] - Impact Testing required
[18] - Impact Testing not required, see UCS-66(b)(3)
[19] - Select a valid hydrotest type to get the UG-20(f) exemption
[20] - Cylinder/Cone Junction MDMT based on Longitudinal Stress considerations
[21] - Bolting Material
Notes:
Impact test temps were not entered in and not considered in the analysis.
UCS-66(i) applies to impact tested materials not by specification and
UCS-66(g) applies to materials impact tested per UG-84.1 General Note (c).
The Basic MDMT includes the (30F) PWHT credit if applicable.
Materials of Construction:
Component Normal Impact
Type Material Class Thickness UNS # ized Tested
Normalized is determined based on the UCS-66 material curve selection and Figure UCS-66.
Impact Tested is based on material selection and material data properties.
Design Str. In
Element Description Pressure Ext. Element Corrosion Flg. Creep
or Type + Stat. head Press. M.A.W.P Allowance Gov. Range
Element "To" Elev Element Nominal Finished Reqd Thk Reqd Thk Long Circ
Length Thickness Thickness Internal External Eff Eff
Type cm cm mm mm mm mm
Wld Flat 6.8 6.8 68.0 68.0 40.7 ... 1.00 0.70
Cylinder 83.4 76.6 12.5 12.5 10.3 ... 1.00 1.00
Cylinder 533.4 450.0 19.0 19.0 10.3 ... 1.00 1.00
Torisph 538.5 5.1 25.0 25.0 19.2 2.2 1.00 1.00
Weights:
Fabricated - Bare W/O Removable Internals 2026.5 kg
Shop Test - Fabricated + Water ( Full ) 4016.5 kg
Shipping - Fab. + Rem. Intls.+ Shipping App. 2026.5 kg
Erected - Fab. + Rem. Intls.+ Insul. (etc) 2026.5 kg
Empty - Fab. + Intls. + Details + Wghts. 2026.5 kg
Operating - Empty + Operating Liquid (No CA) 2026.5 kg
® SPLM Licensed User
PV Elite 2019
PV Elite 2019 SP1 Licensee:
FileName : C-962 Page 20 of 20
Vessel Design Summary: Step: 9 12:17pm Oct 14,2022