Professional Documents
Culture Documents
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Key on and start the engine. Electrical check. Connectors, lead, Check and Repair the wires Engine torque is reduced.
Battery voltage OR Voltage of accelerator position sensor (APS)
APS position error st Make a short circuit of the acceleration short circuit to battery. OR Replace Accelerator Accelerator position sensor
P2128 1 Cycle potentiometer 1 OR Voltage of accelerator position sensor
[Track 2: Short circuit to positive] position sensor 2 to 5 V. Accelerator position sensor (APS) position sensor (APS). OR (APS) value is not
(APS) potentiometer 2.
Wait 500ms. signal too high. Replace Engine control unit. used any more.
Key on and start the engine. Electrical check. Connectors, lead, Check and Repair the wires Engine torque is reduced.
Battery voltage OR Voltage of accelerator position sensor (APS)
APS position error Make a short circuit of the acceleration short circuit to ground. OR Replace Accelerator Accelerator position sensor
P2127 - - potentiometer 1 OR Voltage of accelerator position sensor
[Track 2: Short circuit to ground] position sensor 2 to ground. Accelerator position sensor (APS) position sensor (APS). OR (APS) value is not
(APS) potentiometer 2
Wait 500ms. signal too low. Replace Engine control unit. used any more.
Key on and start the engine. Turn the
Accelerator position sensor (APS)
(around 10% travel and not more than Engine torque is reduced.
APS position error Battery voltage Electrical check. Connectors, Check and Repair the wires
st 40%). Insert a resistor 1.2 kOhm Accelerator position sensor
P2140 [Plausibility between 1 Cycle - Voltage of accelerator position sensor (APS) potentiometer 1 lead, contact resistance OR Replace accelerator
between the acceleration position (APS) value is not
the two tracks] Voltage of accelerator position sensor (APS) potentiometer 2 at sensor 1 and 2. position sensor (APS).
sensor 1 and ground to reduce the used any more.
output voltage of the first channel.
Wait 500ms.
Horizontal cylinder MAP Make a short circuit of the intake Electrical check. Short circuit to Check and Repair the wires
value error st manifold pressure sensor to 5V OR battery or Open circuit. OR Replace intake manifold
P0108 1 Cycle - - No limp home action.
[Open circuit or Short circuit interrupt the sensor circuit. Check connectors. pressure sensor. OR
to positive] Key on and start the engine. Signal voltage too high. Replace Engine control unit.
Vertical cylinder MAP Make a short circuit of the intake Electrical check. Check and Repair the wires
value error st manifold pressure sensor to 5V OR Short circuit to battery or Open OR Replace intake manifold
P2A0D 1 Cycle - - No limp home action.
[Open circuit or Short circuit interrupt the sensor circuit. circuit. Check connectors. pressure sensor. OR
to positive] Key on and start the engine. Signal voltage too high. Replace Engine control unit.
Engine speed
Horizontal cylinder throttle Check and Repair the wires
Time since engine start Install a resistor in series in one
position error st Electrical check. Check OR Replace throttle body.
P0121 1 Cycle - Actual throttle blade position angle of throttle sensor throttle blade sensor. No limp home action.
[TPS 1 - Difference between connectors. OR Replace Engine control
potentiometer 1 minus Actual throttle blade position angle of Key on and start the engine.
track 1 and track 2] unit.
throttle sensor potentiometer 2
1/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Engine speed
Horizontal cylinder throttle Check and Repair the wires
Time since engine start Install a resistor in series in one throttle
position error st Electrical check. OR Replace throttle body.
P0221 1 Cycle - Actual throttle blade position angle of throttle sensor position sensor. No limp home action.
[TPS 2 - Difference between Check connectors. OR Replace Engine control
potentiometer 1 minus Actual throttle blade position angle Key on and start the engine.
track 1 and track 2] unit.
of throttle sensor potentiometer 2
2/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Electrical check.
Horizontal cylinder throttle
Connect the wire of the throttle valve Short circuit to GND.
power stage error st Engine speed
P2102 1 Cycle - actuator to GND. Check wires and connectors. Replace the throttle body. No limp home action.
[Short circuit to ground - final Battery voltage
Key on and start the engine. Blocked/not moving
power stage deactivated]
throttle valve.
Horizontal cylinder throttle error Disconnect the wire of the throttle Electrical check. Open circuit.
st Engine speed
P1181 [Out of tolerance 1 Cycle - valve actuator. Check wires and connectors. Replace the throttle body. No limp home action.
Battery voltage
range - recovery position] Key on and start the engine. Blocked/not moving throttle valve
Before key on, block the throttle valve. No range check of the throttle
Replace the throttle body. No limp home action.
Key on. Do not start the engine. valve is heard at key on.
Horizontal cylinder Engine speed
throttle value error during st Intake air temperature
P1182 1 Cycle -
the initialisation Engine coolant temperature Electrical check.
[Mechanical stop self-learning] Vehicle speed throttle valve in Limp
Connect throttle valve signal1 wire and Short circuit of the signal wires.
home position.
throttle valve signal2 wire of the Check wires and connectors. Replace the throttle body.
About 3% throttle
throttle body. Throttle valve is in limp
valve angle.
home position.
Intake air temperature
Horizontal cylinder throttle Engine coolant temperature
st No possibility to induce a
P1099 self-learning interrupted 1 Cycle - Pedal position - Replace the throttle body. No limp home action.
malfunction manually.
due to incorrect requirements Status safety fuel cut off
Battery voltage OR Rpm OR Vehicle Speed
Intake air temperature
Horizontal cylinder throttle Engine coolant temperature
st No possibility to induce a
P1097 self-learning interrupted due to 1 Cycle - Pedal position - Replace the throttle body. No limp home action.
malfunction manually.
incorrect requirements Status safety fuel cut off
Battery voltage OR Rpm OR Vehicle Speed
Engine speed
Vertical cylinder Check and Repair the
Time since engine start Install a resistor in series in one
throttle position error st Electrical check. wires OR Replace throttle
P0226 1 Cycle - Actual throttle blade position angle of throttle sensor throttle valve sensor. No limp home action.
[TPS 1 - Difference between Check connectors. body. OR Replace Engine
potentiometer 1 minus Actual throttle blade position angle Key on and start the engine.
track 1 and track 2] control unit.
of throttle sensor potentiometer 2
3/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Engine speed
Vertical cylinder Check and Repair the
Time since engine start Install a resistor in series in one
throttle position error st Electrical check. wires OR Replace throttle
P2121 1 Cycle - Actual throttle blade position angle of throttle sensor throttle valve sensor. No limp home action.
[TPS 2 - Difference between Check connectors. body. OR Replace Engine
potentiometer 1 minus Actual throttle blade position angle Key on and start the engine.
track 1 and track 2] control unit.
of throttle sensor potentiometer 2
Engine speed
Vertical cylinder throttle value
st Vehicle speed Before key on, block the throttle valve. No range check of the throttle
P1165 error during the initialisation 1 Cycle - Replace the throttle body. No limp home action.
Engine coolant temperature Key on. Do not start the engine. valve is heard at key on.
[Mechanical stop self-learning]
Intake air temperature
Engine speed
Vertical cylinder throttle value
st Vehicle speed Before key on, block the throttle valve. No range check of the throttle
P1197 error during the repetition of the 1 Cycle - Replace the throttle body. No limp home action.
Engine coolant temperature Key on. Do not start the engine. valve is heard at key on.
mechanical stop self-learning
Intake air temperature
4/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Electrical check.
Vertical cylinder throttle
Connect the wire of the throttle valve Short circuit to GND.
power stage error st Engine speed
P210C 1 Cycle - actuator to GND. Check wires and connectors. Replace the throttle body. No limp home action.
[Short circuit to ground - final Battery voltage
Key on and start the engine. Blocked/not moving
power stage deactivated]
throttle valve.
Disconnect the wire of the Electrical check. Open circuit.
throttle valve actuator. Check wires and connectors. Replace the throttle body. No limp home action.
Vertical cylinder throttle Key on and start the engine. Blocked/not moving throttle valve
st Engine speed
P1497 power stage error 1 Cycle - Battery voltage
[SPI bus] Engine control unit internal
No possibility to induce a Replace the engine
failure. IC internal SPI No limp home action.
malfunction manually. control unit.
communication failure.
Electrical check.
Throttle valve in Limp
Vertical cylinder throttle error Connect throttle valve signal1 wire and Short circuit of the signal wires.
st Engine speed home position.
P1164 [Out of tolerance range - 1 Cycle - throttle valve signal2 wire of Check wires and connectors. Replace the throttle body.
Battery voltage About 3% throttle
recovery position] The throttle body. Throttle valve is in limp
valve angle.
home position.
5/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Mount a faulty oil control valve for the Check and Repair the wires
Vertical cylinder exhaust Time since engine start Camshaft phaser check.
st exhaust camshaft actuator. OR Replace the oil control
P0024 variable camshaft timing error 1 Cycle - Engine speed Oil pressure, power stages, No limp home action.
Start the engine followed valve. OR Replace the
[Target not reached] Commanded change in camshaft position actuator, lead, duct.
by general driving. camshaft phaser.
Mount a faulty oil control valve for the Check and Repair the wires
Horizontal cylinder exhaust Time since engine start Camshaft phaser check.
st exhaust camshaft actuator. OR Replace the oil control
P0014 variable camshaft timing error 1 Cycle - Engine speed Oil pressure, power stages, No limp home action.
Start the engine followed valve. OR Replace the
[Target not reached] Commanded change in camshaft position actuator, lead, duct.
by general driving. camshaft phaser.
Mount a faulty oil control valve for the Check and Repair the wires
Vertical cylinder intake variable Time since engine start Camshaft phaser check.
st intake camshaft actuator. OR Replace the oil control
P0021 camshaft timing error 1 Cycle - Engine speed Oil pressure, power stages, No limp home action.
Start the engine followed valve. OR Replace the
[Target not reached] Commanded change in camshaft position actuator, lead, duct.
by general driving. camshaft phaser.
Mount a faulty oil control valve for the Check and Repair the wires
Horizontal cylinder intake Time since engine start Camshaft phaser check.
st intake camshaft actuator. OR Replace the oil control
P0011 variable camshaft timing error 1 Cycle - Engine speed Oil pressure, power stages, No limp home action.
Start the engine followed valve. OR Replace the
[Target not reached] Commanded change in camshaft position actuator, lead, duct.
by general driving. camshaft phaser.
Battery voltage
Electrical check. Check and Repair the wires
Horizontal cylinder Engine speed Connect the wire of the oxygen
st Short circuit to ground. OR Replace the oxygen
P0131 oxygen sensor error 1 Cycle - Fuel cut off status sensor signal to GND. No limp home action.
Check connectors. sensor. OR Replace the
[Short circuit to ground] Secondary oxygen sensor voltage Key on and start the engine.
Signal voltage too low. engine control module.
Catalyst purging status
Battery voltage
Electrical check. Check and Repair the wires
Vertical cylinder Engine speed Connect the wire of the oxygen sensor
st Short circuit to ground. OR Replace the oxygen
P0151 Oxygen sensor error 1 Cycle - Fuel cut off status signal to GND. No limp home action.
Check connectors. sensor. OR Replace the
[Short circuit to ground] Secondary oxygen sensor voltage Key on and start the engine.
Signal voltage too low. engine control module.
Catalyst purging status
Engine speed
6/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Engine speed
Engine speed
Engine speed
7/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
8/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Electrical check.
Open circuit of ignition coil.
Disconnect the control signal Check and Repair the
Horizontal cylinder main Check connectors. Ignition coil
st Engine speed wire of the ignition coil 1. wires OR Replace the
P0351 spark plug coil error 1 Cycle - voltage is too low, ignition coil No limp home action.
Battery voltage Key on and start the engine ignition coil. OR Replace
[Open circuit] operating voltage is present at
followed by general driving. the engine control module.
the engine control unit. No spark
is present at the spark plug.
Electrical check.
Short circuit to battery voltage.
Connect the control signal wire of the Check and Repair the
Horizontal cylinder main Check connectors. Ignition coil
st Engine speed ignition coil 1 to battery voltage. wires OR Replace the
P2301 spark plug coil error 1 Cycle - operating voltage is too high and No limp home action.
Battery voltage Key on and start the engine followed by ignition coil. OR Replace
[Short circuit to positive] continuously deactivated.
general driving. the engine control module.
No spark is present
at the spark plug.
Electrical check.
Connect the wire of the control signal Short circuit to battery GND. Check and Repair the
Horizontal cylinder main
st Engine speed ignition coil 1 to GND. Check connectors. Ignition coil wires OR Replace the
P2300 spark plug coil error 1 Cycle - No limp home action.
Battery voltage Key on and start the engine operating voltage is too low and ignition coil. OR Replace
[Short circuit to ground]
followed by general driving. continuously activated. No spark the engine control module.
is present at the spark plug.
Electrical check.
Open circuit of ignition coil.
Disconnect the wire of the control Check and Repair the
Vertical cylinder main Check connectors. Ignition coil
st Engine speed signal ignition coil 1. wires OR Replace the
P0352 spark plug coil error 1 Cycle - voltage is too low, ignition coil No limp home action.
Battery voltage Key on and start the engine ignition coil. OR Replace
[Open circuit] operating voltage is present at
followed by general driving. the engine control module.
the engine control unit. No spark
is present at the spark plug.
Electrical check.
Short circuit to battery voltage.
Connect the control signal wire of the Check and Repair the
Vertical cylinder main Check connectors. Ignition coil
st Engine speed ignition coil 1 to battery voltage. wires OR Replace the
P2304 spark plug coil error 1 Cycle - operating voltage is too high and No limp home action.
Battery voltage Key on and start the engine followed by ignition coil. OR Replace
[Short circuit to positive] continuously deactivated.
general driving. the engine control module.
No spark is present at the spark
plug
Electrical check.
Short circuit to battery GND.
Connect the control signal wire of the Check and Repair the
Vertical cylinder main Check connectors.
st Engine speed ignition coil 1 to GND. wires OR Replace the
P2303 spark plug coil error 1 Cycle - Ignition coil operating voltage is No limp home action.
Battery voltage Key on and start the engine ignition coil. OR Replace
[Short circuit to ground] too low and continuously
followed by general driving. the engine control module.
activated. No spark is present at
the spark plug.
Electrical check.
Open circuit of ignition coil.
Check connectors. Ignition coil Check and Repair the
Horizontal cylinder secondary Disconnect the wire of the ignition coil
st Engine speed voltage is too low, ignition coil wires OR Replace the
P0353 spark plug coil error 1 Cycle - 2. Key on and start the engine No limp home action.
Battery voltage operating voltage is present at ignition coil. OR Replace
[Open circuit] followed by general driving.
the engine control unit. the engine control module.
No spark is present
at the spark plug.
9/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Electrical check.
Short circuit to battery voltage.
Connect the control signal wire Check connectors. Check and Repair the
Horizontal cylinder secondary
st Engine speed of the ignition coil 2 to battery voltage. Ignition coil operating voltage wires OR Replace the
P2307 spark plug coil error 1 Cycle - No limp home action.
Battery voltage Key on and start the engine is too high and continuously ignition coil. OR Replace
[Short circuit to positive]
followed by general driving. deactivated. the engine control module.
No spark is present
at the spark plug.
Electrical check.
Open circuit of ignition coil.
Disconnect the control signal wire Check connectors. Ignition coil Check and Repair the
Vertical cylinder secondary
st Engine speed of the ignition coil 2. voltage is too low, ignition coil wires OR Replace the
P0354 spark plug coil error 1 Cycle - No limp home action.
Battery voltage Key on and start the engine operating voltage is present at ignition coil. OR Replace
[Open circuit]
followed by general driving. the engine control unit. the engine control module.
No spark is present
at the spark plug.
Electrical check.
Short circuit to battery voltage.
Connect the control signal wire of the Check and Repair the
Vertical cylinder secondary Check connectors. Ignition coil
st Engine speed ignition coil 2 to battery voltage. wires OR Replace the
P2310 spark plug coil error 1 Cycle - operating voltage is too high and No limp home action.
Battery voltage Key on and start the engine ignition coil. OR Replace
[Short circuit to positive] continuously deactivated.
followed by general driving. the engine control module.
No spark is present
at the spark plug.
Electrical check.
Connect the control signal wire of the Short circuit to battery GND. Check and Repair the
Vertical cylinder secondary
st Engine speed ignition coil 2 to GND. Check connectors. Ignition coil wires OR Replace the
P2309 spark plug coil error 1 Cycle - No limp home action.
Battery voltage Key on and start the engine operating voltage is too low and ignition coil. OR Replace
[Short circuit to ground]
followed by general driving. continuously activated. No spark the engine control module.
is present at the spark plug.
Electrical check.
ECU is in status predrive
Disconnect the battery and replace it Check the generator output
Ignition is on
st with an adjustable voltage power supply. voltage and check the battery Check and Repair the wires
P0562 Battery voltage - undervoltage 1 Cycle - Basic enable conditions met No limp home action.
Adjust the voltage to 9 Volt. voltage in key off. OR Replace the Battery.
No pending or confirmed DTCs
Key on and start the engine. Try to recharge the battery with
Engine operation status running
an external charger.
Electrical check.
Check and Repair the wires
Connect the wire of the engine coolant Short circuit to GND.
Coolant temperature value error st OR Replace engine coolant
P0117 1 Cycle - - temperature sensor to GND. Check connectors. Engine No limp home action.
[Short circuit to ground] temperature sensor OR
Key on and start the engine. coolant temperature sensor
Replace Engine control unit.
signal is too low.
10/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Electrical check.
Connect the wire of the engine coolant Check and Repair the wires
Coolant temperature value error Short circuit to 5V or Open
st temperature sensor to 5V OR OR Replace engine coolant
P0118 [Short circuit to positive 1 Cycle - - circuit. Check connectors. No limp home action.
disconnect the wire. temperature sensor OR
or Open circuit] Engine coolant temperature
Key on and start the engine. Replace Engine control unit.
sensor signal is too high.
Knock sensor error st No possibility to induce a Knock signal is not valid any
P0324 1 Cycle - - Replace engine control unit. No limp home action.
[Signal evaluation error] malfunction manually. more. ECU internal failure.
11/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
12/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
13/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
14/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Engine speed
Engine control unit executes a
Monitoring function error Status Injection cut off
st No possibility to induce a reset. At second failure Replace the engine Engine speed is reduced
P061D [Air mass calculation model 1 Cycle - Status syncronization loss
malfunction manually. occurrence limitation of control module. to 2500rpm.
plausibility] Status predrive
engine speed.
Status postdrive
Engine speed
Status Injection cut off
Actual Air/Fuel ratio value
Engine control unit executes a
Status predrive
Monitoring function error st No possibility to induce a reset. At second failure Replace the engine Engine speed is reduced
P0169 1 Cycle - Status postdrive
[Air/fuel mixture plausibility] malfunction manually. occurrence limitation of control module. to 2500rpm.
Engine speed in the function monitoring
engine speed.
Injection cut off demand in function monitoring
Status syncronization loss
Demand for deactivation of fault reaction
Accelerator position sensor (APS) dependant engine speed
enable condition Engine control unit executes a
Monitoring function error
st Status Injection cut off No possibility to induce a reset. At second failure Replace the engine Engine speed is reduced
P0606 [Cut-off time and ignition 1 Cycle - Status syncronization loss malfunction manually. occurrence limitation of control module. to 2500rpm.
cut-off plausibility]
Status predrive engine speed.
Status postdrive
15/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
5 Volt ECU inner line error st No possibility to induce a Replace the engine
P0643 1 Cycle - Condition Ignition is switched on No supply voltage for sensors. No limp home action.
[Overvoltage] malfunction manually. control module.
5 Volt ECU inner line error st No possibility to induce a Replace the engine
P0642 1 Cycle - Condition Ignition is switched on No supply voltage for sensors. No limp home action.
[Undervoltage] malfunction manually. control module.
Replace connectors or
Check the connectors and wires
Engine operation status running Disconnect the crankshaft sensor from wires. OR Replace the
Engine speed signal st of the crankshaft sensor for short
P0335 1 Cycle - Engine speed the Harness. Short circuit to ground or crankshaft sensor. OR No limp home action.
[Lost signal or open circuit] circuits or interruptions.
Vehicle speed short circuit to battery voltage. Replace the engine
Check if the sensor is mounted.
control module.
16/17
Multistrada 1200 Model Year 2015
MIL
FAULT GENERIC METHOD TO INDUCE A INFORMATION FOR FAILURE
DESCRIPTION ACTIVATION SECONDARY PARAMETERS REPAIR ACTION LIMP HOME ACTION
CODE ERROR LIGHT MALFUNCTION IDENTIFICATION
CRITERIA
Replace connectors or
EXVL exhaust valve Electrical check.
Connect the wire of the wires. OR Replace the
potentiometer error from BBS st Battery voltage Short circuit to battery voltage.
P0079 1 Cycle - exhaust flap to battery voltage. exhaust flap actuator. OR No limp home action.
[Short circuit to ground Engine operation status running Check connectors and wires.
Switch on ignition and start the engine. Replace the engine
or Open circuit] Check sensor.
control module.
Replace connectors or
Electrical check.
EXVL exhaust valve Connect the wire of the wires. OR Replace the
st Battery voltage Short circuit to ground.
P0080 potentiometer error 1 Cycle - exhaust flap to ground. exhaust flap actuator. OR No limp home action.
Engine operation status running Check connectors and wires.
[Short circuit to positive] Switch on ignition and start the engine. Replace the engine
Check sensor.
control module.
Replace connectors or
Disconnect the wire of the Electrical check. wires. OR Replace the
Front wheel speed error st Battery voltage wheel sensor to the ECU.
P2158 1 Cycle - Check connectors and wires. wheel sensor. OR No limp home action.
[Generic Error] Engine operation status running Switch on ignition and start the engine. Check sensor. Replace the engine
control module.
Ambient pressure value error st Engine speed No possibility to induce a malfunction Replace the engine
P2229 1 Cycle - Pressure sensor failure No limp home action
[Short circuit to positive] Battery voltage manually. control module
Ambient pressure value error st Engine speed No possibility to induce a Replace the engine
P2228 1 Cycle - Pressure sensor failure. No limp home action.
[Short circuit to ground] Battery voltage malfunction manually. control module.
Replace connectors or
Disconnect the wire of the Electrical check.
Front wheel speed sensor st Engine operation status running wires. OR Replace the
P0500 1 Cycle - wheel sensor to the ECU. Check connectors and wires. No limp home action.
[Generic Error] Battery voltage wheel sensor. OR Replace
Switch on ignition and start the engine. Check sensor.
the engine control module.
st
P05CB Incompatible Hardware 1 Cycle - - - - - -
17/17