Professional Documents
Culture Documents
Pilot Punches: Dicoat
Pilot Punches: Dicoat
PILOT PUNCHES
®
P.1599
-DICOAT TREATMENT-
+0.01
T-PSTA R≦0.5 R10 Catalog No. - L(LC・LCT・LMT) - P
(PC)-(R=0)-(BC・HC・TC, etc.)
D┄
62~64 HRC
0
Alterations T-STAS 10 - LC75 - PC2.25 - BC13
Surface 3000 HV
P
H−0.2
Equivalent to
0
SKD11
60~63 HRC AT-STA +0.3 B
+0.3 Alteration Code Tip R type Tapered tip 1Code Alteration Code Tip R type Tapered tip 1Code
5 0
Surface 3000 HV S 0
+0.3 Tip diameter change Tip diameter change
D+0.005
0 L 0 R10 Pmin.
PC≧ 2 ≧1.00
Pmin.
PC≧ 2 ≧1.00
Shape of tip changes depending on P dimension. Powdered high- KC Addition of single key flat to head
speed steel 0.01mm increments 0.01mm increments
AT-PSTA PC
PC
P.250
P
62~64 HRC Ymax.=YCmax.(Refer to YC)
For shank diameter tolerance D , select either m5 or +0.005
0 . Surface 3000 HV L For the length of tip R, refer to the products data“Punch R length”. P.1592 P
(PC) Bmax. P(PC) Bmax.
1.00~1.19 15 1.00~1.19 15
® Equivalent to
-Tapered tip・Dicoat treatment- SKD11 1.20~1.99 17 1.20~1.99 17 WKC Addition of double key flats in parallel
60~63 HRC T-TPA max35 ℓ(min3)
−0.01
D−0.03 2.00~2.99 27 2.00~2.99 27

Surface 3000 HV
+0.01
Dm5 X R≦0.5 R10 3.00~3.99 32 3.00~3.99 32
D┄
0
Powdered high- Head thickness is machined to a tolerance
PILOT PUNCHES
4.00~5.99 42 4.00~5.99 42
G±30´
P
speed steel RC of -0.04~0 relative to the retainer surface.
T-PTPA B BC 6.00~ 47 6.00~ 47
Alterations to head
H−0.2
Alterations to tip
−0.04
62~64 HRC
0
BC Cannot be used for D+0.005 types.
Surface 3000 HV 0
+0.3 Tip length change
Equivalent to 5
+0.3 B 0 R0.1∼0.3 2≦BC≦Bmax. 0.1mm increments
0
SKD11 +0.3 (R=0 can be selected.) Full length L must be at least 25mm longer than tip length BC. Head diameter change
AT-TPA F 0 HC
HC
60~63 HRC
H
+0.3 +0.3 D≦HC<H 0.1mm increments
Surface 3000 HV L 0 Y 0 Y
D+0.005
0 R10 Tip R is cut flat.
Powdered high- 2≦RLC<Y<8
speed steel RLC - Head thickness change 2≦TC<5 0.1mm increments
62~64 HRC AT-PTPA Tip length
(B)
P G
P≦1.99 10°
Y=√ P (10-P/4)
TC (If combined with LCT, LMT, TKC, and TKM, 0.01mm increments can be selected.)
For shank diameter tolerance D , select either m5 or +0.005
0 . Surface 3000 HV X>L>S P≧2.00 15° RLC +0.3 0.1mm increments TC Full length L is shortened by (5-TC) .
0 T If combined with LC, full length is equal to LC.
Alterations to shank
LC
(Dm5) 5 L If difference between full length and tip length is 25mm or
high-speed T-PTPA 2 LC Changes to head thickness tolerance and full length are processed using a single code.
4 52 62 72 1.00~ 3.99 7 L The allowable range of change, increments, and notes()are the same as for LC.
steel 15
5 52 62 72 2.00~ 4.99 8
3 LMT TKM LC
6 52 62 72 2.50~ 5.99 9 Head thickness tolerance change + Full length change
0
L 8 52 62 72 82 92 3.00~ 7.99 11 T +0.3
0 ⇨ -0.02
5
10 52 62 72 82 92 102 3.00~ 9.99 21 13
13 52 62 72 82 92 102 6.00~ 12.99 16
Price
(D+0.005 ) (16) 62 72 82 92 102 10.00~ 15.99 19
0 8
~ Equivalent to AT-STA (20) 62 72 82 92 102 13.00~ 19.99 27 23
SKD11 AT-TPA (25) 62 72 82 92 102 18.00~ 24.99 28
3 52 62 72 2.00~ 2.99 5
21 2
4 52 62 72 2.00~ 3.99 7
5 62 72 2.00~ 4.99 8
~ Powdered AT-PSTA 27 3
6 62 72 2.50~ 5.99 9
high-speed AT-PTPA
steel X 8 62 72 82 92 3.00~ 7.99 11
5
10 62 72 82 92 102 3.00~ 9.99 32 13
13 62 72 82 92 102 6.00~ 12.99 16
(16) 72 82 92 102 10.00~ 15.99 19
8
(20) 72 82 92 102 13.00~ 19.99 42 23
(25) 72 82 92 102 18.00~ 24.99 28
D=(16),
(20), and
(25) are specifications available for shank diameter tolerance Dm5 only.
L(42)B=10 If full length is
(42) , tip length B is 10mm.
P>D-0.03ℓ=0 If P>D-0.03, D-0.01 (press-in lead)
-0.03 is not included.
259 260