This document provides instructions for configuring and commissioning a drive system, including:
1) Changing the drive set and performing a factory reset.
2) Setting access authorization levels and commissioning the drive.
3) Defining external power units, adjusting unit currents and supply voltages, and entering motor data.
4) Configuring field control and field weakening, as well as acquiring actual speed values.
5) Completing quick commissioning and executing optimization runs to reduce humming sounds from the motor.
This document provides instructions for configuring and commissioning a drive system, including:
1) Changing the drive set and performing a factory reset.
2) Setting access authorization levels and commissioning the drive.
3) Defining external power units, adjusting unit currents and supply voltages, and entering motor data.
4) Configuring field control and field weakening, as well as acquiring actual speed values.
5) Completing quick commissioning and executing optimization runs to reduce humming sounds from the motor.
This document provides instructions for configuring and commissioning a drive system, including:
1) Changing the drive set and performing a factory reset.
2) Setting access authorization levels and commissioning the drive.
3) Defining external power units, adjusting unit currents and supply voltages, and entering motor data.
4) Configuring field control and field weakening, as well as acquiring actual speed values.
5) Completing quick commissioning and executing optimization runs to reduce humming sounds from the motor.
Press the “Fn” (Function) and “Δ” keys simultaneously.
Press “P” (Program) key to conform. Factory Reset (In Drive – 1) 1. P9 = 30 (Allow for factory reset) 2. P976 = 1 (Factory Reset) After that you find the run-up message. Access Authorization: 3. P0003 = 1 Standard P0003 = 2 Advanced P0003 = 3 Expert, Commissioning (In Drive – 2) 4. P10 = 0 5. P2000 = 1500 RPM (Max. Speed of motor) 6. P10 = 1 Define the external Power Unit 7. P51820 = Rated armature supply voltage Adjust the rated unit currents 8. P50076 (0) = (Motor Armature Current / Drive Armature Current) x 100 9. P50076 (1) = (Motor Field Current / Drive Field Current) x 100 Adjust to the actual unit supply voltage 10. P50078 (0) = Rated value for armature supply voltage (400) 11. P50078 (1) = Rated value for field supply voltage (400) Enter the motor data 12. P50100 (0) = rated armature current (4.0) 13. P50101 (0) = rated armature voltage (440) 14. P50102 (0) = rated excitation current (0.5) 15. P50108 (0) = maximum operating speed (1500) Data for field 16. Control of the field P50082 = 0 Internal field is not used P50082 = 1 the field is activated with the line contactor P50082 = 2 Automatic switching in of the standstill field set P50082 = 3 Field current permanently switched on P50082 = 4 Field with Auxiliaries ON signal activated 17. Field weakening P50081 = 0 No speed dependent P50081 = 1 Field weakening operation by means of internal closed loop EMF control Data for actual speed value acquisition 18. P50083 = 1 Operation with analog tachometer P50083 = 2 Operation with incremental encoder P50083 = 3 Operation without tachometer P50083 = 4 freely wired actual value P50083 = 5 Operation with incremental encoder and SMC30 Complete quick commissioning 19. P3900 = 3 Now you can start the motor with humming sound. Execute optimization runs 20. P50051 = 24 optimization of closed loop field current control 21. P50051 = 25 optimization of closed loop armature current control 22. P50051 = 26 optimization of speed control 23. P50051 = 27 optimization of closed loop emf control 24. P50051 = 28 plotting the friction characteristics Now you can start the motor with reduced humming sound.