Professional Documents
Culture Documents
Numerical Problems Induction Motors
Numerical Problems Induction Motors
1. A three phase, 12 pole, salient pole alternator is coupled to a diesel engine running at 500
rpm. It supplies an induction motor which has a full load speed of 1440 rpm. Find the
percentage slip and number of poles of the induction motor.
2. If the induced emf in the stator of an 8 pole induction motor has a frequency of 50 Hz and
that in the rotor is 1.5 Hz, at what speed is the motor running and what is the slip?
3. A three phase, 50 Hz, 4 pole slip ring induction motor has a star connected rotor. The full
load speed of the motor is 1460 rpm. The rotor resistance and stand still reactance per
phase are 0.1 ohm and 1.5 ohm respectively. The open circuit voltage on open circuit
between the slip rings is 90 volts. Determine (i) percentage slip (ii) induced emf in rotor
per phase (iii) the rotor reactance per phase at full load (iv) the rotor current and full load
power factor.
Page 1 of 3
4. A three phase slip ring induction motor has a star connected rotor. It has an induced emf
of 60 volts on open circuit between the slip rings at stand still when the rated voltage is
supplied to the stator. The resistance and stand still reactance of rotor per phase are 0.5 Ω
and 5 Ω respectively. Determine the rotor current per phase (i) when the rotor is at stand
still and connected to a star connected rheostat of resistance 5 Ω and reactance of 0.5 Ω
per phase. (ii) when running at 4 % slip with rheostat short circuited.
Soln: Current through rotor at stand still = current at starting
5. A three phase 3 kV, 24 pole, 50Hz, star connected slip ring induction motor has a rotor
resistance of 0.015 Ω and a stand still reactance of 0.265 Ω per phase. Full load torque is
obtained at a speed of 245 rpm. Calculate (i) ratio of maximum to full load torque. (ii)
Speed at maximum torque. Neglect stator impedance.
7. No load and short circuit tests conducted on 3φ, 5 HP, 220 volts, 60 Hz, 1800 rpm
induction motor gave the following results.
No load test: 220 volts, 4.35 amps, 244 watts
Short circuit test: Voltage of 220 volts produces a current of 64.5 Amps; Resistance per
phase = 0.545 ohms, Friction, windage and core loss = 213 watts. Obtain the equivalent
circuit parameters. ( Ans: X m = 29.2 Ω, Z e = 1.97 Ω, R e = 1.054 Ω, X e = 1.665 Ω, R 2 =
0.509 Ω)
Page 2 of 3
8. A three phase, 50 Hz, 6 pole squirrel cage induction motor runs at 960 rpm on full load.
The stand still rotor resistance and reactance per phase are 0.01 ohm and 0.05 ohm
respectively. Express the maximum torque developed in terms of full load toque. Find the
slip at which the maximum torque occurs. (Ans: T max = 2.6T f , 20%)
9. A water pump employs 3 phase, 50 HP induction motor which is started using a star delta
starter. It is fed from feeder mains with a 3 phase, 440 volts, 50 Hz supply. Because of
the drops in the feeder it is found that the starting torque is same for both star and delta
connections. Calculate the resistance of the feeder. From the short circuit test on the
motor the following details are obtained: V = 200 volts, I = 125 Amps, and pf = 0.4. If an
identical feeder is run in parallel with the first one find the % increase in starting torque
obtained with each connection. (Ans: 1.6 Ω, 37%, 119%)
10. A three phase, 50 Hz, 4 pole slip ring induction motor runs at 1455 rpm on full load. The
rotor resistance per phase on stand still is 0.2 ohm. It is required to reduce the speed by
10% by inserting the series resistance in the rotor circuit. Determine the rotor resistance
per phase required. (Ans: 0.6467 ohm)
11. A three phase 4 pole 50 Hz induction motor has a sinusoidaly distributed air gap
flux/pole of 0.05 wb. The ratio of rotor leakage reactance to resistance under blocked
rotor condition is 4. Determine the amplitude of rotor mmf required to produce a torque
of 60 Nm when the motor is running at a slip of 33.33%. ( Ans: 318 AT)
12. Two induction motors are cascaded for the purpose of speed control. The main motor has
6 poles and the other motor has 4 poles. Calculate the possible speed that can be obtained
if the set is run on a supply of 50 Hz frequency. (Ans: 3000 rpm, 1500 rpm, 1000 rpm &
600 rpm)
13. An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor
resistance per phase of the winding is 0.2 ohm. What external resistance per phase must
be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the
torque remains same in both the cases. (Ans: 1.1 ohm)
14. An 8 pole 50 Hz, three phase induction motor runs at a speed of 720 rpm when delivering
full load torque. Its stand still rotor resistance and reactance are 0.1 ohm and 0.6 ohm per
phase respectively. An additional resistance of 0.5 ohm per phase is inserted in the rotor
circuit to control the speed. Calculate the speed at which the motor runs now with full
load torque remaining the same. (Ans: 570 rpm)
15. A three phase induction motor designed for a rated voltage of V 1 at 50 Hz is accidentally
switched on directly to a voltage of V 2 at 60 Hz. Stator impedance of the motor is
negligible. Calculate the ratios of currents and torques at starting and maximum torques
when V 2 = V 1 . Also find the ratio of V 2 to V 1 to obtain the same values of starting
current and torque at 60 Hz. (Ans: 0.834, 0.695, 0.695, ; 1.2)
Page 3 of 3