Professional Documents
Culture Documents
P R O D U C T C ATA LO G
OVRH catalog
Surge protective devices
2 S E RIE S S U R G E P R OT E C T I V E D E V I C E S
OV RH SE
—
SPDs
Surge Protective Devices (SPDs) are designed to protect against transient surge
conditions. Lighting and utility power anomalies only account for 20% of
transient surges, while the other 80% are produced internally in a facility.
Transient surges can reach values of hundreds of Large transient surge conditions can damage
thousands of volts or instantaneous current flow of printed circuit board traces and puncture
tens of thousands of amperes, but typically last less semiconductors causing immediate or intermittent
than one hundred microseconds in duration. These equipment failures. Continued exposure to surges
internally generated transients can be caused by can degrade printed circuit board traces or
switching power supplies (computers), electronic semiconductors resulting in seemingly random
ballasts (building lighting) and variable frequency delayed equipment failures. Therefore, equipment
drives (air handlers, elevators, etc). The most failures cannot always be contributed to a single
destructive transient voltage surges can be power quality event. Surge remnants on data lines
attributed to lightning and utility load switching; can alter digital data and logic levels causing
however, experts predict that these two events equipment failures and lockups.
account for 20% of all transient surge activity.
Professionally installed ABB products provide
Reliable data sources suggest that lightning strikes superior protection against transient surges
have current magnitudes in excess of 200,000 preventing unnecessary downtime and costly
amps. Moreover, lightning strikes are not single repairs.
strike events. Strikes typically consist of four to
six “hits” and sometimes can be as high as 40kA.
Therefore, SPDs must be appropriately sized to
provide adequate protection during multiple
surge events.
—
Table of contents
012– 013 OVRHSP/OVRHSR
014 OVRHTE
015 OVRHT3B
016 OVRHT3C
017– 018 OVRHS3U
019 OVRHLD
4 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
IEC and UL SPD test standards–terminology
—
UL Type 1 vs IEC Class I tested SPDs
OVRT1
—
Type 2 vs Class II tested SPDs
OVRHTE
Healthcare Education
Almost every piece of modern medical equipment depends on Most school systems utilize state of the art multi-media outlets
electrical power. The more sophisticated the technology, the which result in more computers in the classrooms. Surge
more susceptible it is to the devastating effects of transient protection devices helps to ensure these computers stay up and
surge events. running, keeping growing minds energized!
7
—
Type 3 SPDs
UL Type 3 SPD
Type 3 SPDs are installed at a conductor length of
10 meters (30 feet) or more from the electrical panel
they are protecting. These devices are typically cord
connected, direct plug-in, receptacle type SPDs
installed at the load equipment being protected. No ABB offering
Manufacturing/Industrial Commercial/Retail
Improvements to manufacturing devices have migrated Companies are now installing efficient ballasts, dimmers, and
manufacturers to human machine combinations for maximizing integrated renewable energy systems. Surge protection devices
the manufacturing output capacities of facilities. Surge help protect these new technologies which are more susceptible to
protection devices protect this equipment from damage caused power quality events.
by large variations in the current and voltage, thus ensuring
uptime in manufacturing production.
8 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
Type 4 and Type 5 SPDs
—
UL Types vs IEC Class tested SPDs
and Locations
Transformer
Service
Disconnect
UL Types Type 2
Type 3 (plug-In)
Class I
IEC Class tested (Type 1)
(EN Type) Class II or Class I + II
(Type 1 or Type 1 + 2)
Class III or Class II + III
(Type 3 or Type 1 + 2)
10 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
Where Surge Protective Devices are applied
Closer to the critical load. OVRHSP 240kA–120kA OVRHSP 120kA–80kA • Emergency power backup
A unit installed here protects OVRHT3 series and • Transfer switches
from internally generated OVRHS3U series • Control boxes
surges and isolates critical • Switchgear
equipment from faults. OVRHTE 100kA–50kA • Generators
• Computer servers
• Building management systems
• Surveillance equipment
• Security systems
• HVAC
• Building management systems
• Fire alarm panels
• Copiers
• Telephone systems
• Fax machines
Point of use
—
OVRH series product range
Name OVRHSP OVRHSP OVRHSP (60, OVRHSR OVRHTE OVRHT3B OVRHT3C OVRHS3U OVRHLD
(200, 240, (120, 160) 80, 100) (120, 160)
300, 400)
SPD Type Type 1 Type 1 Type 1 Type 1 Type 2 Type 1 Type 1 Type 1 and Type 1
Type 2
Certifications UL 1449 and UL 1449 and UL 1449 and UL 1449 and UL 1449 UL 1449 UL 1449 UL 1449 UL 1449
CE CE CE CE
Surge Ratings 200, 240, 120, 160kA 60, 80, 100kA 120, 160kA 25, 50, 80 50kA per 50kA per 40kA per 20, 25, 30kA
300, 400kA per phase per phase per phase and 100 phase phase phase per phase
per phase per mode
LEDs Yes Yes Yes Yes Yes Yes Yes Yes Yes
Dry Relay Standard Standard Optional Standard Optional Not available Not available Optional Not available
Contacts
EMI Filter Optional Optional Optional Optional Optional Not available Not available Not available Not available
Surge Counter Optional Optional Not available Not available Not available Not available Not available Not available Not available
Warranty 5 years 5 years 5 years 5 years 3 years 3 year 3 year 1 year 1 year
12 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
OVRHSP/OVRHSR Surge protective devices
Heavy duty for service entrance applications
Product features
• Listed to UL 1449 4th Edition for Type 1 and Type 2 SPD
applications.
• Fail-safe design with individually fused Metal Oxide Varistors
(MOVs) eliminating single point failure, protecting against
both overcurrent and overvoltage events.
• 200kAIC short circuit rating permits direct bus connection to
most electrical services.
• Low let through voltage ensured by the lowest possible
impedance path to ground and equal current sharing during
surge events.
• All weather sealed, powder-coated NEMA 4/IP65 housing is
designed for any orientation and indoor/outdoor applications.
Available configurations
• 5-year standard warranty.
Model number Voltage Configuration
OVRHSP and OVRHSR
OVRHSP(SR)xxx1201P
OVRHSP(SR)xxx2401P
120V
240V
1-phase, 2-wire + ground
1-phase, 2-wire + ground
Product specifications
OVRHSP(SR)xxx1202S 120/240V 2-phase, 3-wire + ground
Electrical
OVRHSP(SR)xxx1203Y 120/208V 3-phase Wye, 4-wire + ground
Nominal discharge current rating (I-n) 10kA (60–100) 20kA (120–400)
OVRHSP(SR)xxx2203Y 220/380V 3-phase Wye, 4-wire + ground
Operating frequency 47–63Hz
OVRHSP(SR)xxx2403Y 240/415V 3-phase Wye, 4-wire + ground
OVRHSP(SR)xxx2773Y 277/480V 3-phase Wye, 4-wire + ground Connection method arallel to electrical distribution
P
system
OVRHSP(SR)xxx3473Y* 347/600 3-phase Wye, 4-wire + ground
Modes of protection All modes (L-N, L-G, N-G, L-L)
OVRHSP(SR)xxx1203H 120/240V 3-phase High-Leg, 4-wire + ground
OVRHSP(SR)xxx2403D 240V 3-phase Delta, 3-wire + ground Fault rating (SCCR) 200kAIC–no upstream
over-current protection device
OVRHSP(SR)xxx3803D* 380V 3-phase Delta, 3-wire + ground
(breaker or fuse) required
OVRHSP(SR)xxx4803D* 480V 3-phase Delta, 3-wire + ground
Response time Less than 1 nanosecond
OVRHSP(SR)xxx6003D* 600V 3-phase Delta, 3-wire + ground
Standard monitoring (120–400kA) tatus indicator lights
S
OVRHSP: Where “xxx” can be 60, 80, 100, 120, 160, 200, 240, 300 or 400
(one per phase)
OVRHSR: Where “xxx” can be 120 or 160
Standard dry (Form “C”)
*Voltages not available with 60, 80 or 100kA units relay contacts
Available options Model Audible alarm with silence button
Add applicable suffix to end of numbers number*
Mechanical
Advanced monitoring (available in 60–100kA units only) 1 Weight 0, 80, 100kA: 4.5 kg (10 lbs.)
6
(Includes dry relay contacts, audible alarm,
120, 160kA: 9 kg (20 lbs.)
alarm silence button, fault light)
200, 240, 300, 400kA: 18 kg (40 lbs.)
Transient filter* and advanced monitoring A
Enclosure type owder coated, impact-resistance
P
Stainless steel enclosure and advanced monitoring M
steel, weather-proof NEMA 4
Stainless steel enclosure, transient filter* and advanced N
monitoring Installation location Indoor/outdoor
Transient filter* (meets UL 1283) (All models) 3 Mounting method Dual mounting flanges
Stainless steel enclosure (All models) 4 Operating environment -40° to +70°C (-40° to +185°F)
Transient filter* and surge counter (SP 120–400kA only) B Altitude Up to 4000 m (13,000 ft.)
Transient filter* and stainless steel enclosure (All models) C Product design arallel design with individually
P
Surge counter and stainless steel enclosure (SP 120–400kA only) D fused MOVs
Transient filter*, surge counter and stainless steel enclosure T Regulatory
(SP 120–400kA only) UL 1449 4th Edition Type Type 1
*Not recommended when using telecommunication rectifiers.
UL 1283 Yes
OVRHSR stand alone option (To be ordered as a separate item)
IEEE C62.41.1, .2, C62.45 Yes
Flush-mount plate kit OVRHSR-FMP-120/160
Listed by TL: 60–100kA models
E
EMI/RFI filter attenuation
UL: 120–400kA models
Max. attenuation frequency 41dB @ 106kHz CE: 120–400kA models
Warranty
5-years
13
—
Dimensional specifications (D)
(W1)
.8
83 .20)
.5 (3 (W2)
34 .36)
(1
(D) (W1)
(H1)
(H2)
(H1) (H3)
(H1) (H2)
(H2) (H3)
(H3)
Allowable area for conduit entry Allowable area for conduit entry
—
The OVRHSR compact design allows for it to be recessed into the wall.
Stud (W1)
Drywall
(D1) (D2) (W2)
OVRHSR
Flush-mount
Ø 7.87 (0.31)
120, 160kA
plate 19.05
(3/4) Dim Millimeters (Inches)
Myers Hub
OVRHSR H1 254.0 (10.00)
unit
H2 273.1 (10.75)
H3 292.1 (11.50)
W1 203.2 (8.00)
(H1)
W2 152.4 (6.00)
(H2)
(H3) D1 106.9 (4.20)
D2 50.8 (2.00)
14 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
OVRHTE Surge protective devices
Medium duty for distribution applications
Product features
• Listed to UL 1449 4th edition for Type 2 SPD applications.
• Protects facilities and equipment against the harmful effects
of lightning strikes and internally generated electrical
transients.
• Includes pre-wired pigtail conductors to streamline
installation.
• Features internal copper bus conduction path to minimize
system impedances, lowering clamping voltage and increasing
protection.
Product specifications
Available configurations Electrical
Nominal discharge current rating (I-n) 20kA
Model number Voltage Configuration
Operating frequency 47–63Hz
OVRHTExx1201P 120V 1-phase, 2-wire + ground
Connection methods arallel to load (shunt)
P
OVRHTExx2401P 240V 1-phase, 2-wire + ground 609.6mm (24") 5mm2 (#10 AWG) wires
OVRHTExx1202S 120/240V 2-phase, 3-wire + ground through 20A (max) breaker
OVRHTExx1203Y 120/208V 3-phase Wye, 4-wire + ground Modes of protection L-L, L-N, L-G, N-G
OVRHTExx2203Y 220/380V 3-phase Wye, 4-wire + ground Fault rating (SCCR) 65kAIC–upstream over-current
OVRHTExx2403Y 240/415V 3-phase Wye, 4-wire + ground protection device (breaker or fuse
required)
OVRHTExx2773Y 277/480V 3-phase Wye, 4-wire + ground
Response time ess than 1 nanosecond (one per
L
OVRHTExx3473Y 347/600V 3-phase Wye, 4-wire + ground
phase)
OVRHTExx1203H 120/240V 3-phase Hi-Leg, 4-wire + ground
Standard monitoring LED status indicator lights
OVRHTExx2403D 240V 3-phase Delta, 3-wire + ground
Mechanical
OVRHTExx3803D 380V 3-phase Delta, 3-wire + ground
Weight 5.8 kg (12.7 lbs.)
OVRHTExx4803D 480V 3-phase Delta, 3-wire + ground
Enclosure type EMA 4X fiberglass-reinforced
N
Model number: Where “xx” can be 25, 50, 80, or 100 polyester (FRP) surface-mount, non-
Available option Model number* removable cover
Dry Form “C” relay contacts 5 Installation location Indoor/outdoor
*Add applicable suffix to the end of Model number. Mounting methods Dual mounting flanges
Example: OVRHTE251201P5 Operating environment 40° to +60°C (-40° to +140°F)
EMI/RFI filter attenuation Altitude Up to 5000 m (16,400 ft.)
Max. attenuation frequency 50dB @ 100kHz Product design No internal fusing
Warranty Regulatory
3-years UL 1449 4th edition type Type 2
UL 1283 Yes
— IEEE C62.41.1, .2, C62.45 Yes
(W2)
(D)
(W1)
—
OVRHT3B Surge protective devices
Medium duty for residential or industrial applications
Product features
• Listed to UL 1449 4th Edition for Type 1 SPD applications.
• 50kA per phase protection.
• Individual thermally fused and protected MOVs.
• Includes pre-wired pigtail conductors.
• Multiple MOVs per phase eliminates single point failure.
Product specifications
Available configurations
Electrical
Model number kA per Voltage Configuration Nominal discharge current rating (I-n) 10kA
phase
OVRHT3B501201P 50kA 120V 1-phase, 2-wire + ground Operating frequency 47–63Hz
OVRHT3B502401P 50kA 240V 1-phase, 2-wire + ground Connection methods Parallel to load
OVRHT3B502771P 50kA 277V 1-phase, 2-wire + ground 914.4mm (36") of 3.31mm2 (#12 AWG)
wires
OVRHT3B504801P 50kA 480V 1-phase, 2-wire + ground
OVRHT3B501202S 50kA 120/240V 2-phase, 3-wire + ground Modes of protection Model dependent
OVRHT3B502402S 50kA 240/480V 2-phase, 3-wire + ground Fault rating (SCCR) 100 kAIC
OVRHT3B502403H 50kA 120/240V 3-phase High-Leg, 4-wire + ground Response time Less than 1 nanosecond
OVRHT3B501203Y 50kA 120/208V 3-phase Wye, 4-wire + ground (one per phase)
OVRHT3B502203Y 50kA 220/380V 3-phase Wye, 4-wire + ground Standard monitoring LED status indicator lights
OVRHT3B502303Y 50kA 230/400V 3-phase Wye, 4-wire + ground Mechanical
OVRHT3B502403Y 50kA 240/415V 3-phase Wye, 4-wire + ground Weight .9 kg (2 lbs.)
OVRHT3B502773Y 50kA 277/480V 3-phase Wye, 4-wire + ground Enclosure type NEMA 4X, non-metallic
OVRHT3B503473Y 50kA 347/600V 3-phase Wye, 4-wire + ground Installation location Indoor/Outdoor
OVRHT3B502403D 50kA 240V 3-phase Delta, 3-wire + ground
Mounting method 12.7mm (1/2")–14 NPT thread
OVRHT3B503803D 50kA 380V 3-phase Delta, 3-wire + ground
Operating environment -35° to +80°C (-31° to +176°F)
OVRHT3B504003D 50kA 400V 3-phase Delta, 3-wire + ground
OVRHT3B504803D 50kA 480V 3-phase Delta, 3-wire + ground Altitude Up to 5000 m (16,400 ft.)
OVRHT3B506003D 50kA 600V 3-phase Delta, 3-wire + ground Product design Individual thermally fused and
Earthing Systems protected MOVs
OVRHT3B502301PI 50kA 230V 1-phase, 2-wire + ground Regulatory
(for TNC earthing systems) UL 1449 4th edition type Type 1
OVRHT3B502301PJ 50kA 230V 1-phase, 2-wire + ground UL 96A Yes
(for TNS earthing systems) IEEE C62.41.1, .2, C62.45 Yes
OVRHT3B502301PK 50kA 230V 1-phase, 2-wire + ground
Listed by UL
(for IT earthing systems)
OVRHT3B502301PL 50kA 230V 1-phase, 2-wire + ground
(for TT earthing systems)
Warranty
3-year
—
Dimensional specifications
Dim Millimeters (Inches)
12.7mm (1/2")-14 NPS thread W 90.0 (3.36)
D 75.0 (2.93)
75mm
(2.93") H 75.0 (2.93)
3.31mm2 (#12 AWG) stranded wire
600V PVC insulation
914.4mm (36") long
64mm
(2.52")
16 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
OVRHT3C Surge protective devices
Medium duty for residential or industrial applications
Product features
• Listed to UL 1449 4th Edition for Type 1 SPD applications.
• 50kA per phase protection.
• Individual thermally fused and protected MOVs.
• Includes pre-wired pigtail conductors.
• Multiple MOVs per phase eliminates single point failure.
Product specifications
Electrical
Available configurations Nominal discharge current rating (I-n) 10kA
Operating frequency 47–63Hz
Model number kA per Voltage Configuration Connection methods Parallel to load
phase 914.4mm (36") of 3.31mm2 (#12 AWG)
OVRHT3C501201P 50kA 120V 1-phase, 2-wire + ground wires
OVRHT3C502401P 50kA 240V 1-phase, 2-wire + ground Modes of protection Model dependent
OVRHT3C502771P 50kA 277V 1-phase, 2-wire + ground
Fault rating (SCCR) 100 kAIC
OVRHT3C504801P 50kA 480V 1-phase, 2-wire + ground
Response time Less than 1 nanosecond
OVRHT3C501202S 50kA 120/240V 2-phase, 3-wire + ground
(one per phase)
OVRHT3C502402S 50kA 240/480V 2-phase, 3-wire + ground
Standard monitoring LED status indicator lights
OVRHT3C502403H 50kA 120/240V 3-phase High-Leg, 4-wire + ground
Mechanical
OVRHT3C501203Y 50kA 120/208V 3-phase Wye, 4-wire + ground
OVRHT3C502203Y 50kA 220/380V 3-phase Wye, 4-wire + ground Weight .9 kg (2 lbs.)
OVRHT3C502303Y 50kA 230/400V 3-phase Wye, 4-wire + ground Enclosure type NEMA 4X, non-metallic
OVRHT3C502403Y 50kA 240/415V 3-phase Wye, 4-wire + ground Installation location Indoor/Outdoor
OVRHT3C502773Y 50kA 277/480V 3-phase Wye, 4-wire + ground Mounting method 12.7mm (1/2")–14 NPT thread
OVRHT3C503473Y 50kA 347/600V 3-phase Wye, 4-wire + ground Operating environment -35° to +80°C (-31° to +176°F)
OVRHT3C502403D 50kA 240V 3-phase Delta, 3-wire + ground Altitude Up to 5000 m (16,400 ft.)
OVRHT3C503803D 50kA 380V 3-phase Delta, 3-wire + ground
Product design Individual thermally fused and
OVRHT3C504003D 50kA 400V 3-phase Delta, 3-wire + ground protected MOVs
OVRHT3C504803D 50kA 480V 3-phase Delta, 3-wire + ground
Regulatory
OVRHT3C506003D 50kA 600V 3-phase Delta, 3-wire + ground
UL 1449 4th edition type Type 1
Earthing Systems
UL 96A Yes
OVRHT3C502301PI 50kA 230V 1-phase, 2-wire + ground
(for TNC earthing systems) IEEE C62.41.1, .2, C62.45 Yes
OVRHT3C502301PJ 50kA 230V 1-phase, 2-wire + ground Listed by UL
(for TNS earthing systems)
OVRHT3C502301PK 50kA 230V 1-phase, 2-wire + ground
(for IT earthing systems)
OVRHT3C502301PL 50kA 230V 1-phase, 2-wire + ground
(for TT earthing systems)
Warranty
3-year
— D3
—
OVRHS3U Surge protective devices
Medium duty for residential or industrial applications
Product features
• Listed to UL 1449 4th Edition for Type 1 and Type 2
SPD applications.
• Individual fusing for each Metal Oxide Varistors (MOVs).
• LED indicates proper functioning of L-N and N-G MOVs.
Product specifications
Electrical
Nominal discharge current rating (I-n) 20kA
Operating frequency 47–63Hz
Connection methods arallel to load (shunt)
P
2mm2 (#14 AWG) wires
Modes of protection Model dependent
Fault rating (SCCR) 100kAIC
Response time ess than 1 nanosecond
L
(one per phase)
Standard monitoring LED status indicator lights
Mechanical
Available configurations Weight .9 kg (2 lbs.)
Enclosure type NEMA 1, non-metallic
Model number kA per Voltage Configuration Installation location Indoor
Phase Mounting method 1 2.7mm (1/2")–14 NPT thread
Type 1 (Aluminum bracket optional)
OVRHS3U401201P 40kA 120V 1-phase, 2-wire + ground Operating environment -40° to +80°C (-40° to +176°F)
OVRHS3U401202S 40kA 120/240V 2-phase, 3-wire + ground Altitude Up to 5000 m (16,400 ft.)
OVRHS3U402403D 40kA 240V 3-phase Delta, 4-wire + ground Product design Individually fused MOVs
OVRHS3U401203Y 40kA 120/208V 3-phase Wye, 4-wire + ground Regulatory
Type 2 UL 1449 4th edition type Type 1 and Type 2
OVRHS3U402401P 40kA 240V 1-phase, 2-wire + ground UL 1283 nly for model number
O
OVRHS3U801202SR 80kA 120/240V 2-phase, 3-wire + ground OVRHS3U802402SR
OVRHS3U404803D 40kA 480V 3-phase Delta, 3-wire + ground IEEE C62.41.1, .2, C62.45 Yes
OVRHS3U401203H 40kA 120/240V 3-phase High-Leg, 4-wire + ground Listed by UL
OVRHS3U402773Y 40kA 277/480V 3-phase Wye, 4-wire + ground
OVRHS3U402303Y 40kA 230/400V 3-phase Wye, 4-wire + ground
Available options Model
(Not available on OVRHS3U802402SR unit) number*
1 set of dry relay contacts (all models) 5
See Dimensional specifications
1 set of dry relay contacts + mounting bracket P on following page.
(only on OVRHS3U402401P and OVRHS3U402303Y models)
*Add applicable suffix to the end of Model number
Example: OVRHS3U401201P5
Warranty
1-year
18 OV RH SE RIE S S U R G E P R OT E C T I V E D E V I C E S
—
OVRHS3U Dimensional specifications
DRY RELAY CONTACTS, 5 OPTION
142mm
(5.6") .136 dia. blind holes, .40 deep
41mm 58mm for #8 self-tapping screws (2)
(1.60") (2.30") 6mm
(0.25")
51mm
(2.00")
49mm
(1.94")
M4 threaded hole
4 plcs. Dim Millimeters (Inches)
W 49.0 (1.94)
H 210.0 (8.25)
1 1
2
RE
3
2 M
OT
E
3 AL
AR
M
12mm 7mm
(.47") (.28") Mounting
25mm bracket
(1.000")
LED
19mm (.75")
Dim Millimeters (Inches)
W 73.0 (2.90)
73mm
(2.90") 2
2mm (#14 AWG) D 51.0 (2.00)
stranded wire
600V PVC insulation H 142.0 (5.60)
450mm (18") long
142mm
(5.6") .136 dia. blind holes, .40 deep
41mm 58mm for #8 self-tapping screws (2)
(1.60") (2.30") 6mm
(0.25")
51mm
(2.00")
—
OVRHLD Surge protective devices
Light duty for AC applications
Product features
• Listed to UL 1449 4th edition for Type 1 SPD applications.
• Multiple Metal Oxide Varistors (MOVs), with individual current
fusing and thermal disconnects for each MOV.
• LED indicates proper functioning of L-N MOVs.
Product specifications
Electrical
Nominal discharge current rating (I-n) 10kA
Operating frequency 47–63Hz
—
Dimensional specifications
69mm
(2.72")
2mm2 (#14 AWG)
56mm) 54mm stranded wire
(2.2") (2.13") 600V PVC insulation
450mm (18") long
Dim Millimeters (Inches)
W 56.0 (2.20)
56mm D1 54.0 (2.13)
(2.2")
D2 69.0 (2.72)
H 56.0 (2.20)
12.7mm (1/2")–14 NPS thread
Locknut
—
Power Protection
5900 Eastport Boulevard
Richmond, VA 23231-4453 USA
Tel: +1 800 292 3739
Fax: +1 804 236 4047
abb.com
Additional information
We reserve the right to make technical
changes to the product and to the
information in this document without
notice. The agreed conditions at the time
of the order shall apply. ABB assumes no
090417
© Copyright 2017 Thomas and Betts Power Solutions, LLC. All rights reserved.
Specifications subject to change without notice.