Professional Documents
Culture Documents
Rating Book 2019 Meccalte
Rating Book 2019 Meccalte
Ratings Book
Guida Tecnica
Potenze
Ratings Definitions 6
Dynamic Data Support 6
Environmental Considerations 7
Additional Information
Wiring Connection Diagram 40
SAE Coupling and Mounting Guide 42
Rating Definitions
Standby Rating Prime Rating
Standby Rating is selected for supplying emergency Prime Rating is the maximum power available at a
power for the duration of normal power interruption. variable load for an unlimited number of hours: it
Overload on this rating is not allowed. allows the possibility of a 10% overload.
From the generator point of view, if the emergency This is equivalent to Prime Power in accordance
power is required continuously for more than one with ISO8528 and Overload Power in accordance
hour sizing is in accordance with 150°/40° or 163°/27° with ISO3046, AS2789, DIN6271, and BS5514. From
conditions. Also, if the overload duration is less than one the generator point of view, it is sized according to
hour, then the generator accepts 10% overload above the class B, F, H temperature rise requirements or
Prime Ratings for 125°/40° or the 125°/27° ratings. 125°/27° rating.
In the ‘Ratings Book’ you can find ratings for: In the ‘Ratings Book’ you can find ratings for:
150°/40°: Peak continuous ratings according to 80°/40°: this condition is equivalent to Class B
ISO8528-3. temperature rise. 10% overload on 1 hour over 6
hours is allowed.
163°/27°: Emergency peak continuous rating, not
defined in ISO specification. Suitable for stand-by 105°/40°: this condition is equivalent to Class F
sizing only. temperature rise. 10% overload on 1 hour over 6
hours is allowed.
The ratings are then suitable for supplying continuous
electrical power, at variable load, for the duration 125°/40°: this condition is equivalent to Class H
of any utility power failure. These ratings allow temperature rise. 10% overload on 1 hour over 6
temperature to rise above the temperature rise class hours is allowed.
H limit which can result in a shorter insulation life.
The 10% overload is not available at these ratings.
125°/27°: ratings at this condition are equivalent to
those listed for the 150°/40° condition if not listed.
10% overload on 1 hour over 6 hours is allowed.
Altitude Derations/Environmental
Temperature & Altitude
Environmental Concerns
Environmental Concerns
Generators are often exposed to harmful airborne impregnation technologies, like Vacuum Pressure
pollutants, like sand and saltwater which may require Impregnation (VPI) or with the use of dedicated roll
some form of protection to reduce or eliminate these and dip or trickle machines. This impregnation quality
harmful agents. Common elements like dirt, gravel or process is perfect for the vast majority of applications,
rock dust can create abrasive and potentially damaging however in order to achieve the same results in
insulation reliability when environmental or operating
conditions are demanding, it is possible to consider
extend the life of the protective insulation, it may be
Mecc Alte. Please refer to our separate Technical guide:
manufacture. It is also extremely important to recognize Insulation Protection Systems for further guidance
on our; standard, standard+, grey, grey+ and total+
through the generator and create additional heat in the systems. Please note on some specific models a slight
windings. It is also important to understand that the use power de-rate is considered when the total systems are
of filters requires a strict maintenance regime. applied.
Mecc Alte uses premium class H insulation material. Please consult your Mecc Alte Representative for
Impregnation processes are achieved with the latest application reviews and recommendations.
Altitude Derations/Environmental
Ingress Protection IP Ratings
IP23 IP43
INGRESS PROTECTION INGRESS PROTECTION
8 | www.meccalte.com
AVR Controlled Ratings 3ph 400V 50Hz 1500rpm
Volts
ECP28 L4 C 122 12 DSR 27.5 25.5 25 23 20
3 ph ECP28 VL4 C 142 12 DSR 33 30.5 30 26 24
/ 400
50 ECP32 1S4 C 153 12 DSR 41 39 37.5 35 30
THREE PHASE
12 4
/ 230
HERTZ HERTZ ECP32 1M4 C 186 12 DSR 55 52.5 50 48 40
ECP32 2M4 C 212 12 DSR 68.8 65 62.5 59.5 50
TWELVE WIRE FOUR WIRE ECP32 1L4 C 244 12 DSR 82.5 78 75 67 60
/ 200
ECP32 2L4 C 252 12 DSR 91 85 82.5 73.2 66
ECP34 1S4 C 302 12 DSR 96 93 87.5 79 70
1500 1800 ECP34 2S4 C 349 12 DSR 110 105 100 90 80
115
RPM RPM
ECP34 1M4 C 370 12 DSR 137 132 125 112 100
ECP34 2M4 C 388 12 DSR 148 143 135 121 108
RCM
ECP34 1L4 C 423 12 DSR 165 158 150 136 120
DIGITAL RCM
VOLTAGE REGULATOR
ECP34 2L4 C 440 12 DSR 181 174 165 149 132
3000
BRUSH ELECTRONIC
VOLTAGE REGULATOR
3600
BRUSHLESS
VOLTAGE REGULATOR
BRUSHLESS CAPACITOR
All machines have ECO40 2L4 B 1536 12 DER-1/A 735 700 680 630 544
an auxiliary winding ECO40 VL4 B 1752 12 DER-1/A 825 777 750 690 600
/ 800
‘standard’ with 300% ECO43 1S4 A 1920 12 DER-1/A 900 840 800 730 640
short circuit capability. ECO43 2S4 A 2140 12 DER-1/A 1016 975 930 850 744
/ 460
Indicated rating ECO43 1M4 A 2275 12 DER-1/A 1120 1070 1025 950 820
references to series or ECO43 2M4 A 2370 12 DER-1/A 1250 1200 1150 1050 920
parallel star connection ECO43 2L4 A 2700 12 DER-1/A 1420 1358 1300 1200 1040
/ 400
as per published table. ECO43 VL4 A 2980 12 DER-1/A 1540 1480 1400 1280 1120
On ECO40, ECO43 and
ECO46 1S4 A 3005 12 DER-1/A 1650 1552 1500 1350 1200
ECO46 1.5S4 A 3375 12 DER-1/A 1800 1700 1650 1480 1320
parallel configurations
230
are available on specific ECO46 2S4 A 3560 12 DER-1/A 1944 1863 1800 1600 1440
request: consult a Mecc ECO46 1L4 A 3805 12 DER-1/A 2268 2173 2100 1900 1680
Alte representative for ECO46 1.5L4 A 4255 12 DER-1/A 2500 2380 2300 2050 1840
more information. ECO46 2L4 A 4375 12 DER-1/A 2700 2588 2500 2250 2000
ECO46 VL4 A 5120 12 DER-1/A 3024 2899 2800 2500 2240
SPECIAL WINDING
Volts
HERTZ
/ 380
ph
/ 220
ECP32 1M4 C
ECP32 2M4 C
186
212
12
12
DSR
DSR
55
68.8
52.5
65
50
62.5
48
59.5
40
50
12 HERTZ
/ 190
TWELVE WIRE
110
ECP34 1M4 C 370 12 DSR 137 132 125 112 100 RPM RPM
3000
VOLTAGE REGULATOR
ECO38 2S4 A 573 12 DSR 220 211 200 185 160 RPM RPM
ECO38 3S4 A 602 12 DSR 250 237 225 207 180 2G DIGITAL AVR
ECO38 1L4 A 692 12 DSR 275 264 250 230 200 DER2
2G DIGITAL
BRUSHED B
VOLTAGE REGULATOR VOLTAGE REGULATOR
ECO38 2L4 A 790 12 DSR 330 315 300 275 240
VOLTAGE REGULATOR
ECO43 1S4 A 1920 12 DER-1/A 900 840 800 730 640 an auxiliary winding
ECO43 2S4 A 2140 12 DER-1/A 1016 975 930 850 744 ‘standard’ with 300%
short circuit capability.
/ 440
ECO43 VL4 A 2980 12 DER-1/A 1540 1480 1400 1280 1120 parallel star connection
ECO46 1S4 A 3005 12 DER-1/A 1650 1552 1500 1350 1200 as per published table.
On ECO40, ECO43 and
ECO46 1.5S4 A 3375 12 DER-1/A 1800 1700 1650 1480 1320
220
10 | www.meccalte.com
AVR Controlled Ratings 3ph 415V 50Hz 1500rpm
POLE
50 6 POLE
60 ECP28 2S4 C
ECP28 3S4 C
91
97
12
12
DSR
DSR
16.5
19.2
15.4
18
15
17.5
14.1
16.5
12
14
Volts
HERTZ HERTZ
ECP28 M4 C 106 12 DSR 22 20.5 20 18.5 16
ECP28 L4 C 122 12 DSR 27.5 25.5 25 23 20
3 ph ECP28 VL4 C 142 12 DSR 33 30.5 30 26 24
/ 415
50 ECP32 1S4 C 153 12 DSR 41 39 37.5 35 30
THREE PHASE
/ 240
12 HERTZ
4 HERTZ
ECP32 1M4 C
ECP32 2M4 C
186
212
12
12
DSR
DSR
55
68.8
52.5
65
50
62.5
48
59.5
40
50
ECP32 1L4 C 244 12 DSR 82.5 78 75 67 60
/ 208
TWELVE WIRE FOUR WIRE
120
RPM RPM ECP34 1M4 C 370 12 DSR 137 132 125 112 100
ECP34 2M4 C 388 12 DSR 148 143 135 121 108
RCM
ECP34 1L4 C 423 12 DSR 165 158 150 136 120
DIGITAL RCM
VOLTAGE REGULATOR ECP34 2L4 C 440 12 DSR 181 174 165 149 132
3000 3600 ECO38 1S4 A 530 12 DSR 196 188 180 170 144
BRUSH ELECTRONIC BRUSHLESS BRUSHLESS CAPACITOR
VOLTAGE REGULATOR VOLTAGE REGULATOR
All machines have ECO40 2L4 B 1536 12 DER-1/A 735 700 680 630 544
an auxiliary winding ECO40 VL4 B 1752 12 DER-1/A 825 777 750 690 600
/ 830
‘standard’ with 300% ECO43 1S4 A 1920 12 DER-1/A 900 840 800 730 640
short circuit capability. ECO43 2S4 A 2140 12 DER-1/A 1016 975 930 850 744
/ 480
Indicated rating ECO43 1M4 A 2275 12 DER-1/A 1120 1070 1025 950 820
references to series or ECO43 2M4 A 2370 12 DER-1/A 1140 1096 1050 960 840
parallel star connection ECO43 2L4 A 2700 12 DER-1/A 1420 1358 1300 1200 1040
/ 415
as per published table. ECO43 VL4 A 2980 12 DER-1/A 1440 1400 1330 1210 1064
On ECO40, ECO43 and ECO46 1S4 A 3005 12 DER-1/A 1650 1552 1500 1350 1200
ECO46 1.5S4 A 3375 12 DER-1/A 1800 1700 1650 1480 1320
240
parallel configurations
ECO46 2S4 A 3560 12 DER-1/A 1944 1863 1800 1600 1440
are available on specific
ECO46 1L4 A 3805 12 DER-1/A 2268 2173 2100 1900 1680
request: consult a Mecc
Alte representative for ECO46 1.5L4 A 4255 12 DER-1/A 2500 2380 2300 2050 1840
more information. ECO46 2L4 A 4375 12 DER-1/A 2700 2588 2500 2250 2000
ECO46 VL4 A 5120 12 DER-1/A 2916 2795 2700 2400 2160
ECP34 2L4 C 440 12 DSR 181 174 165 149 132 VOLTAGE REGULATOR
DIGITAL
VOLTAGE REGULATOR
3000
ECO38 1S4 A 530 12 DSR 196 188 180 170 144
3600
3000
BRUSH ELECTRONIC
VOLTAGE REGULATOR
ECO38 3L4 A 930 12 DSR 370 360 350 320 280 VOLTAGE REGULATOR
12 | www.meccalte.com
AVR Controlled Ratings 3ph 440V 50hz 1500rpm
RPM: 1500
Insulation: Class H
POLE
50 6 POLE
60 ECP28 2S4 C
ECP28 3S4 C
91
97
12
12
DSR
DSR
–
17.5
–
16.5
–
16
–
14.9
–
12.8
Volts
HERTZ HERTZ
ECP28 M4 C 106 12 DSR 20.4 19 18.5 17.5 14.8
ECP28 L4 C 122 12 DSR – – – – –
3 ECP28 VL4 C 142 12 DSR – – – – –
/ 440
ph
/ 254
ECP32 1M4 C 186 12 DSR 44 42 40 38 32
12 HERTZ
4 HERTZ
/ 220
TWELVE WIRE FOUR WIRE
127
RPM RPM
ECP34 1M4 C 370 12 DSR 117 112 106 96 85
ECP34 2M4 C 388 12 DSR 125 120 114 103 91
RCM ECP34 1L4 C 423 12 DSR 137 131 125 113 100
DIGITAL
VOLTAGE REGULATOR
RCM
ECP34 2L4 C 440 12 DSR 170 163 155 139 124
3000
BRUSH ELECTRONIC
VOLTAGE REGULATOR
3600
BRUSHLESS
VOLTAGE REGULATOR ECO38 1S4 A
BRUSHLESS CAPACITOR
530 12 DSR 180 173 165 155 132
ECO38 2S4 A 573 12 DSR 209 200 190 175 152
RPM RPM
ECO38 3S4 A 602 12 DSR 234 221 210 190 168
AVR
DER2 ECO38 1L4 A 692 12 DSR 253 243 230 215 184
2G DIGITAL AVR
BRUSHED
VOLTAGE REGULATOR
DER2
BRUSH COMPOUND
ECO38 2L4 A 790 12 DSR 319 305 290 265 232
VOLTAGE REGULATOR VOLTAGE REGULATOR
ECO38 3L4 A 930 12 DSR 360 350 340 310 272
ECO40 1S4 B 1049 12 DER-1/A 404 386 370 342 296
ECO40 2S4 B 1133 12 DER-1/A 393 375 360 330 288
BRUSHLESS ELECTRONIC BRUSHLESS COMPOUND ECO40 3S4 B 1208 12 DER-1/A 503 479 460 414 368
ECO40 1L4 B 1323 12 DER-1/A 546 515 500 454 400
ECO40 1.5L4 B 1458 12 DER-1/A 616 588 570 515 456
Volts
‘standard’ with 300% ECO43 1S4 A 1920 12 DER-1/A 815 790 750 663 600
short circuit capability. ECO43 2S4 A 2140 12 DER-1/A 907 870 830 770 664
/ 508
parallel configurations ECO46 2S4 A 3560 12 DER-1/A 1720 1650 1600 1440 1280
are available on specific
ECO46 1L4 A 3805 12 DER-1/A 1990 1900 1850 1660 1480
request: consult a Mecc
Alte representative for ECO46 1.5L4 A 4255 12 DER-1/A 2375 2275 2200 1950 1760
more information. ECO46 2L4 A 4375 12 DER-1/A 2450 2350 2280 2050 1824
ECO46 VL4 A 5120 12 DER-1/A 2150 2060 2000 1780 1600
SPECIAL WINDING
3000
ECP34 1L4 C 423 12 DSR 90 85 83 74 66
3600
3000
BRUSH ELECTRONIC
VOLTAGE REGULATOR
VOLTAGE REGULATOR
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
The Weights are the same as the ‘standard’ 3 phase Models.
Ratings with damper cage.
Consult Factory to choose for your application.
14 | www.meccalte.com
AVR Controlled Ratings 1ph Reconnected Winding 230V 50Hz 1500rpm
SPECIAL WINDING
1 ph
ECP28 M4 C
ECP28 L4 C
106
122
12
12
DSR
DSR
13.3
16.2
12.7
15.1
12.2
14.9
11.1
13.6
9.8
11.9
50
SINGLE PHASE
ECP28 VL4 C 142 12 DSR 20 19 18.5 16.5 14.8
60 ECP32 1S4 C 153 12 DSR 24 23 22 21 17.6
12 HERTZ
DIGITAL
ECP34 1M4 C 370 12 DSR 69 65 63 58 50
VOLTAGE REGULATOR
ECP34 2M4 C 388 12 DSR 73 69 67 62 54
3000
BRUSH ELECTRONIC
VOLTAGE REGULATOR
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
The Weights are the same as the ‘standard’ 3 phase Models.
Ratings with damper cage.
Consult Factory to choose for your application.
2G DIGITAL
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability. BRUSHLESS ELECTRONIC BRU
VOLTAGE REGULATOR
16 | www.meccalte.com
AVR Controlled Ratings 1ph Dedicated Winding 230V 50Hz 1500rpm
1 ph 3 ph
ECP28 M4 C
ECP28 L4 C
106
122
4
4
DSR
DSR
14.2
17.7
13.3
16.4
13
16.2
12
14.8
10.4
13
50
SINGLE PHASE
2G DIGITAL AVR
BRUSHLESS ELECTRONIC DER2
BRUSHLESS COMPOUND All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
VOLTAGE REGULATOR VOLTAGE REGULATOR
SPECIAL WINDING
Volts
MULTI POLE 6 POLE
HERTZ HERTZ
/ 480
ECP28 VL4 C 142 12 DSR 39.6 36.6 36 32 29 ph ph
60 400THREE PHASE
/ 277
ECP32 1M4 C
ECP32 2M4 C
186
212
12
12
DSR
DSR
66
82.5
63
77.5
60
75
58
71.5
48
60
HERTZ
12 HERTZ
/ 240
ECP32 1L4 C 244 12 DSR 99 93.7 90 83 72 TWELVE WIRE
138
ECP34 2S4 C 349 12 DSR 132 126 120 109 96
1800
ECP34 1M4 C 370 12 DSR 165 159 150 135 120
RPM RPM RPM
DIGITAL
ECP34 2L4 C 440 12 DSR 218 208 198 178 158 VOLTAGE REGULATOR VOLTAGE REGULATOR
3000
ECO38 1S4 A 530 12 DSR 236 230 220 205 176
3600
3000 3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
ECO38 3L4 A 930 12 DSR 444 438 420 385 336 VOLTAGE REGULATOR
ECO43 1S4 A 1920 12 DER-1/A 1050 1008 960 875 768 an auxiliary winding
ECO43 2S4 A 2140 12 DER-1/A 1220 1170 1116 1020 893 ‘standard’ with 300%
short circuit capability.
/ 554
ECO43 VL4 A 2980 12 DER-1/A 1824 1765 1700 1540 1360 parallel star connection
ECO46 1S4 A 3005 12 DER-1/A 1944 1875 1800 1620 1440 as per published table.
ECO46 1.5S4 A 3375 12 DER-1/A 2140 2040 1980 1780 1584 On ECO40, ECO43 and
277
18 | www.meccalte.com
AVR Controlled Ratings 3ph 460V 60Hz 1800rpm
POLE
60 6 POLE
ECP28 2S4 C
ECP28 3S4 C
91
97
12
12
DSR
DSR
19.8
23
18.5
21.6
18
21
16.8
19.6
14.4
16.8
Volts
HERTZ
ECP28 M4 C 106 12 DSR 26.4 24.6 24 22 19.2
ECP28 L4 C 122 12 DSR 33 30.6 30 27.5 24
3 ECP28 VL4 C 142 12 DSR 39.6 36.6 36 32 29
/ 460
ph
/ 266
186
12 HERTZ
4 ECP32 1M4 C
ECP32 2M4 C 212
12
12
DSR
DSR
66
82.5
63
77.5
60
75
58
71.5
48
60
ECP32 1L4 C 244 12 DSR 96 91 87 83 69.6
/ 230
TWELVE WIRE FOUR WIRE
133
RPM ECP34 1M4 C 370 12 DSR 165 159 150 135 120
ECP34 2M4 C 388 12 DSR 178 172 162 146 130
RCM
ECP34 1L4 C 423 12 DSR 198 189 180 163 144
RCM
DIGITAL
VOLTAGE REGULATOR ECP34 2L4 C 440 12 DSR 218 208 198 178 158
3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
BRUSHLESS
VOLTAGE REGULATOR ECO38 1S4 A
BRUSHLESS CAPACITOR
530 12 DSR 236 230 220 205 176
ECO38 2S4 A 573 12 DSR 264 253 240 220 192
RPM
All machines have ECO40 2L4 B 1536 12 DER-1/A 882 840 816 756 653
an auxiliary winding ECO40 VL4 B 1752 12 DER-1/A 970 925 900 830 720
/ 920
‘standard’ with 300% ECO43 1S4 A 1920 12 DER-1/A 1050 1008 960 875 768
short circuit capability. ECO43 2S4 A 2140 12 DER-1/A 1220 1170 1116 1020 893
/ 530
Indicated rating ECO43 1M4 A 2275 12 DER-1/A 1290 1227 1180 1080 944
references to series or ECO43 2M4 A 2370 12 DER-1/A 1525 1450 1400 1300 1120
parallel star connection ECO43 2L4 A 2700 12 DER-1/A 1700 1630 1560 1440 1248
/ 460
as per published table. ECO43 VL4 A 2980 12 DER-1/A 1824 1765 1700 1540 1360
On ECO40, ECO43 and ECO46 1S4 A 3005 12 DER-1/A 1944 1875 1800 1620 1440
ECO46 1.5S4 A 3375 12 DER-1/A 2140 2040 1980 1780 1584
266
parallel configurations
ECO46 2S4 A 3560 12 DER-1/A 2332 2236 2160 1920 1728
are available on specific
ECO46 1L4 A 3805 12 DER-1/A 2722 2608 2520 2280 2016
request: consult a Mecc
Alte representative for ECO46 1.5L4 A 4255 12 DER-1/A 2980 2860 2760 2460 2208
more information. ECO46 2L4 A 4375 12 DER-1/A 3240 3105 3000 2700 2400
ECO46 VL4 A 5120 12 DER-1/A 3575 3426 3310 2980 2648
SPECIAL WINDING
Volts
MULTI POLE 6 POLE
HERTZ HERTZ
ECP28 M4 C 106 12 DSR 25.3 23.6 23 20 18.4
ECP28 L4 C 122 12 DSR 30.3 28 27.5 25.5 22
1 3
/ 440
ECP28 VL4 C 142 12 DSR 39.6 36.6 36 32 29 ph ph
60 400THREE PHASE
/ 254
ECP32 1M4 C 12 DSR 66 63 60 58 48
ECP32 2M4 C
186
212 12 DSR 80 74 72.5 70 58
HERTZ
12 HERTZ
/ 220
244 TWELVE WIRE
127
ECP34 2S4 C 349 12 DSR 132 126 120 109 96
1800
ECP34 1M4 C 370 12 DSR 154 147 140 125 112
RPM RPM RPM
DIGITAL
ECP34 2L4 C 440 12 DSR 210 201 191 165 153 VOLTAGE REGULATOR VOLTAGE REGULATOR
3000
ECO38 1S4 A 530 12 DSR 236 230 220 205 176
3600
3000 3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
ECO38 3L4 A 930 12 DSR 444 438 420 385 336 VOLTAGE REGULATOR
ECO40 2L4 B 1536 12 DER-1/A 843 803 780 720 624 All machines have
ECO40 VL4 B 1752 12 DER-1/A 970 925 900 830 720 an auxiliary winding
/ 880
ECO43 1S4 A 1920 12 DER-1/A 1050 1008 960 875 768 ‘standard’ with 300%
ECO43 2S4 A 2140 12 DER-1/A 1159 1111 1060 969 850 short circuit capability.
/ 508
ECO43 1M4 A 2275 12 DER-1/A 1200 1144 1100 1000 880 Indicated rating
ECO43 2M4 A 2370 12 DER-1/A 1420 1357 1300 1200 1040 references to series or
ECO43 2L4 A 2700 12 DER-1/A 1618 1550 1482 1368 1186 parallel star connection
/ 440
ECO43 VL4 A 2980 12 DER-1/A 1824 1765 1700 1540 1360 as per published table.
ECO46 1S4 A 3005 12 DER-1/A 1847 1770 1710 1530 1368 On ECO40, ECO43 and
ECO46 1.5S4 A 3375 12 DER-1/A 2030 1936 1880 1690 1504
254
parallel configurations
ECO46 2S4 A 3560 12 DER-1/A 2213 2122 2050 1820 1640
are available on specific
ECO46 1L4 A 3805 12 DER-1/A 2582 2473 2390 2150 1912
request: consult a Mecc
ECO46 1.5L4 A 4255 12 DER-1/A 2829 2715 2620 2330 2096 Alte representative for
ECO46 2L4 A 4375 12 DER-1/A 3067 2939 2840 2550 2272 more information.
ECO46 VL4 A 5120 12 DER-1/A 3375 3234 3125 2800 2500
20 | www.meccalte.com
AVR Controlled Ratings 3ph 415V 60Hz 1800rpm
POLE
60 6 POLE
ECP28 2S4 C
ECP28 3S4 C
91
97
12
12
DSR
DSR
17
19.8
15.9
18.5
15.4
18
14.6
17
12.4
14.4
Volts
HERTZ
/ 415
ECP32 1S4 C 153 12 DSR 43.5 42 39.5 37 31.6
400
THREE PHASE
/ 240
12 HERTZ
4 ECP32 1M4 C
ECP32 2M4 C
186
212
12
12
DSR
DSR
60.5
76
58
71
55
69
53
63
44
55.2
ECP32 1L4 C 244 12 DSR 86 81 78 73 62.4
/ 208
TWELVE WIRE FOUR WIRE
120
RPM ECP34 1M4 C 370 12 DSR 143 137 130 116 104
ECP34 2M4 C 388 12 DSR 154 148 140 125 112
RCM
ECP34 1L4 C 423 12 DSR 165 158 150 132 120
DIGITAL RCM
VOLTAGE REGULATOR ECP34 2L4 C 440 12 DSR 187 179 170 155 136
3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
BRUSHLESS
VOLTAGE REGULATOR
ECO38 1S4 A
BRUSHLESS CAPACITOR
530 12 DSR 225 220 210 195 168
ECO38 2S4 A 573 12 DSR 253 242 230 210 184
RPM
an auxiliary winding ECO43 1S4 A 1920 12 DER-1/A 962 924 880 800 704
‘standard’ with 300% ECO43 2S4 A 2140 12 DER-1/A 1115 1069 1020 935 816
/ 480
short circuit capability. ECO43 1M4 A 2275 12 DER-1/A 1147 1117 1050 960 840
Indicated rating ECO43 2M4 A 2370 12 DER-1/A 1300 1250 1200 1090 960
references to series or ECO43 2L4 A 2700 12 DER-1/A 1585 1516 1451 1339 1161
/ 415
parallel star connection ECO43 VL4 A 2980 12 DER-1/A 1736 1680 1600 1450 1280
as per published table. ECO46 1S4 A 3005 12 DER-1/A 1728 1656 1600 1440 1280
On ECO40, ECO43 and ECO46 1.5S4 A 3375 12 DER-1/A 1870 1782 1730 1570 1384
240
60 400
THREE PHASE
ECP32 1M4 C
ECP32 2M4 C
186
212
12
12
DSR
DSR
60.5
76
58
71
55
69
53
63
44
55.2
HERTZ
12 HERTZ
3000
ECO38 1S4 A 530 12 DSR 225 220 210 195 168
3600
3000 3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
22 | www.meccalte.com
AVR Controlled Ratings 3ph 400V 60Hz 1800rpm
POLE
60 6 POLE
ECP28 2S4 C
ECP28 3S4 C
91
97
12
12
DSR
DSR
16.8
19.6
15.7
18.3
15.3
17.8
14.4
16.8
12.2
14.2
HERTZ
Volts
ECP28 L4 C 122 12 DSR 28 26 25.5 23.5 20.4
3 ph ECP28 VL4 C 142 12 DSR 34.6 32.4 31.5 27.3 25.2
/ 400
ECP32 1S4 C 153 12 DSR 41 39 37.5 35 30
400
THREE PHASE
/ 230
12 HERTZ
4 ECP32 1M4 C
ECP32 2M4 C
186
212
12
12
DSR
DSR
55
68.8
53
65
50
62.5
48
58
40
50
ECP32 1L4 C 244 12 DSR 82.5 80 75 67 60
/ 200
TWELVE WIRE FOUR WIRE
115
RPM ECP34 1M4 C 370 12 DSR 143 137 130 117 104
ECP34 2M4 C 388 12 DSR 154 148 140 126 112
RCM
ECP34 1L4 C 423 12 DSR 170 163 155 140 124
DIGITAL RCM
VOLTAGE REGULATOR ECP34 2L4 C 440 12 DSR 187 178 170 155 136
3600
VOLTAGE REGULATOR VOLTAGE REGULATOR
ECO38 1S4 A 530 12 DSR 212 204 195 185 156
ECO38 2S4 A 573 12 DSR 235 224 213 197 170
RPM
parallel star connection ECO43 1S4 A 1920 12 DER-1/A 929 892 850 778 680
as per published table. ECO43 2S4 A 2140 12 DER-1/A 1071 1027 980 900 784
/ 460
On ECO40, ECO43 and ECO43 1M4 A 2275 12 DER-1/A 1173 1124 1075 985 860
ECO43 2M4 A 2370 12 DER-1/A 1310 1254 1200 1100 960
parallel configurations ECO43 2L4 A 2700 12 DER-1/A 1497 1430 1370 1256 1096
are available on specific
/ 400
SPECIAL WINDING
Volts
ECP28 3S4 C 97 12 DSR 19.3 18 17.5 16.5 14 MULTI POLE 6 POLE
HERTZ
ECP28 M4 C 106 12 DSR 22 20.5 20 18.5 16
ECP28 L4 C 122 12 DSR 27.5 25.5 25 23 20
/ 380
ECP28 VL4 C 142 12 DSR 33 31 30 26 24 3 ph
/ 220
THREE PHASE
/ 190
ECP32 1L4 C 244 12 DSR 82.5 80 75 67 60 TWELVE WIRE
110
ECP34 2S4 C 349 12 DSR 110 105 100 90 80 1800
ECP34 1M4 C 370 12 DSR 137 132 125 113 100 RPM
DIGITAL
ECP34 2L4 C 440 12 DSR 181 174 165 149 132 VOLTAGE REGULATOR
ECO38 1S4 A 530 12 DSR 196 188 180 170 144 3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
ECO38 3L4 A 930 12 DSR 370 360 350 320 280 VOLTAGE REGULATOR
ECO43 1S4 A 1920 12 DER-1/A 896 861 820 751 656 an auxiliary winding
ECO43 2S4 A 2140 12 DER-1/A 1038 996 950 871 760 ‘standard’ with 300%
/ 440
ECO43 1M4 A 2275 12 DER-1/A 1140 1093 1045 957 836 short circuit capability.
ECO43 2M4 A 2370 12 DER-1/A 1278 1223 1170 1072 936 Indicated rating
ECO43 2L4 A 2700 12 DER-1/A 1442 1379 1320 1210 1056 references to series or
/ 380
ECO43 VL4 A 2980 12 DER-1/A 1502 1453 1400 1280 1120 parallel star connection
ECO46 1S4 A 3005 12 DER-1/A 1675 1610 1550 1420 1240 as per published table.
ECO46 1.5S4 A 3375 12 DER-1/A 1830 1740 1690 1550 1350 On ECO40, ECO43 and
220
24 | www.meccalte.com
AVR Controlled Ratings 3ph Dedicated Winding 380V 60Hz 1800rpm
POLE
60 6 POLE
ECP28 VL4 C
ECP32 1S4 C
142
153
12
12
DSR
DSR
39.6
49.5
36.6
47
36
45
32
43
29
36
HERTZ
VOLTAGE REGULATOR
ECO40 1L4 B 1323 12 DER-1/A 690 650 630 573 504
ECO40 1.5L4 B 1458 12 DER-1/A 810 775 750 677 600
ECO40 2L4 B 1536 12 DER-1/A 882 840 816 756 653
BRUSHLESS ELECTRONIC BRUSHLESS COMPOUND
ECP34 1S4 C
ECP34 2S4 C
302
349
12
12
DSR
DSR
115
132
111
126
105
120
95
109
84
96
12 HERTZ
ECP34 1M4 C 370 12 DSR 165 159 150 135 120 TWELVE WIRE
DIGITAL
ECO38 1L4 A 692 12 DSR 308 295 280 260 224 VOLTAGE REGULATOR
3600
BRUSH ELECTRONIC
ECO38 2L4 A 790 12 DSR 396 378 360 330 288 VOLTAGE REGULATOR
ECO40 3S4 B 1208 12 DER-1/A 656 625 600 540 480 VOLTAGE REGULATOR
26 | www.meccalte.com
AVR Controlled Ratings 3ph Dedicated 690 V 60Hz 1800rpm
12 HERTZ
4 ECP34 1S4 C
ECP34 2S4 C
302
349
12
12
DSR
DSR
115
132
111
126
105
120
95
109
84
96
TWELVE WIRE FOUR WIRE ECP34 1M4 C 370 12 DSR 165 159 150 135 120
ECP34 2M4 C 388 12 DSR 178 172 162 146 130
ECP34 1L4 C 423 12 DSR 198 189 180 163 144
1800 ECP34 2L4 C 440 12 DSR 218 208 198 178 158
RPM
ECO38 1S4 A 530 12 DSR 236 230 220 205 176
ECO38 2S4 A 573 12 DSR 264 253 240 220 192
RCM
ECO38 3S4 A 602 12 DSR 300 284 270 250 216
DIGITAL RCM
VOLTAGE REGULATOR
ECO38 1L4 A 692 12 DSR 330 316 300 280 240
3600
BRUSH ELECTRONIC BRUSHLESS BRUSHLESS CAPACITOR
RPM
ECO38 3L4 A 930 12 DSR 444 438 420 385 336
AVR
ECO40 1S4 B 1049 12 DER-1/A 525 500 480 440 384
DER2 AVR ECO40 2S4 B 1133 12 DER-1/A 590 563 540 490 432
2G DIGITAL
DER2
BRUSHED BRUSH COMPOUND
VOLTAGE REGULATOR
ECO40 3S4 B 1208 12 DER-1/A 656 625 600 540 480
VOLTAGE REGULATOR VOLTAGE REGULATOR
SPECIAL WINDING
50
ECP28 VL4 C 142 12 DSR 23 22 21 19.5 16.8
60 400
SINGLE PHASE
12 HERTZ
ECO38 3S4 A 602 12 DSR 118 114 110 100 88 VOLTAGE REGULATOR
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
The Weights are the same as the ‘standard’ 3 phase Models.
Ratings with damper cage.
Consult Factory to choose for your application.
28 | www.meccalte.com
AVR Controlled Ratings 1ph Reconnected Winding 240V 60Hz 1800rpm
SPECIAL WINDING
DIGITAL
ECP34 1M4 C 370 12 DSR 68 64 62 56 49.6
VOLTAGE REGULATOR
ECP34 2M4 C 388 12 DSR 72 68 66 60 52.8
3600
BRUSH ELECTRONIC
VOLTAGE REGULATOR
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
The Weights are the same as the ‘standard’ 3 phase Models.
Ratings with damper cage.
Consult Factory to choose for your application.
50
ECP28 VL4 C 142
153
4 DSR 27.3 25.7 25 22 20
60 400
SINGLE PHASE
4
HERTZ
2G DIGITAL
BRUSHLESS ELECTRONIC BR
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability. VOLTAGE REGULATOR
All the above machines are 4 lead. Ratings with damper cage.
Consult Factory to choose for your application.
30 | www.meccalte.com
AVR Controlled Ratings 1ph Dedicated Winding 240V 60Hz 1800rpm
1 ph 3 ph
ECP28 M4 C
ECP28 L4 C
106
122
4
4
DSR
DSR
17.1
20.7
16
19.3
15.7
19
14.4
17.4
12.6
15.2
400
SINGLE PHASE THREE PHASE
ECP28 VL4 C 142 4 DSR 24 22.6 22 20 17.6
ECP32 1S4 C 153 4 DSR 30.5 29 28 26 22
4
HERTZ
2G DIGITAL AVR
BRUSHLESS ELECTRONIC DER2
BRUSHLESS COMPOUND
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
VOLTAGE REGULATOR VOLTAGE REGULATOR
All the above machines are 4 lead. Ratings with damper cage.
Consult Factory to choose for your application.
50
2 POLE 4P
3600
BRUSH ELECTRONIC
Brushless capacitor excited machines specifically for Metal Halide light tower lamps.
For custom voltages or non-standard lamp striking voltages, please refer to Factory.
32 | www.meccalte.com
NPE Alternator Range 4 Pole | Brushless AVR - Space Saver
NPE32 1M4 C 98 12 17.6 16.7 16 14.8 12.8 20.9 19.9 19 17.2 15.2
HERTZ
NPE32 2M4 C 109 12 22 20.9 20 18.2 16 26.4 24.9 24 21.7 19.2
POLE 6 POLE
SPACE SAVER
NPE 32 L4 C 120 12 27.5 26.2 25 23 20 34.1 32.5 31 28.5 24.8
NPE32 VL4 C 145 12 38.5 36.4 35 31.8 28 46.2 43.7 42 38.3 33.6
50
60 1Phase (Dedicated Winding) kVA 115/230V 50 Hz, 1.0pf kVA 120/240V 60 Hz, 1.0pf
HERTZ
MODEL WEIGHT (kg) LEADS 163/27 150/40 125/40 105/40 80/40 163/27 150/40 125/40 105/40 80/40
NPE32 1S4 C 77 12 6.5 6.3 6 5.8 4.8 8.7 8.3 8 7.6 6.4
1 ph
NPE32 2S4 C 83 12 9.8 9.4 9 8.6 7.2 12 11.5 11 10.5 8.8
SINGLE PHASE
NPE32 1M4 C 98 12 14.7 14.3 13.5 13 10.8 18 17.3 16.5 15.9 13.2
NPE32 2M4 C 109 12 18.5 17.9 17 16.4 13.6 22.9 22.2 21 19.8 16.8
3 ph NPE 32 L4 C 120 12 21.8 21.1 20 18.9 16 27.3 26.1 25 23.9 20
NPE32 VL4 C 145 12 29.4 28.8 27 25.2 21.6 35.4 34.3 32.5 30.7 26
THREE PHASE
1500 1Phase (Re-connected) kVA 115/230V 50 Hz, 1.0pf kVA 120/240V 60 Hz, 1.0pf
1800
RPM
MODEL WEIGHT (kg) LEADS 163/27 150/40 125/40 105/40 80/40 163/27 150/40 125/40 105/40 80/40
NPE32 1S4 C 77 12 5.5 5.3 5 4.5 4 7.1 6.9 6.5 5.9 5.2
NPE32 2S4 C 83 12 7.6 7.5 7 6.3 5.6 8.7 8.4 8 7.2 6.4
DIGITAL
NPE32 1M4 C 98 12 12 11.5 11 9.8 8.8 14.2 13.6 13 11.7 10.4
3000
VOLTAGE REGULATOR
NPE32 2M4 C 109 12 14.7 14.2 13.5 12.2 10.8 18.5 17.9 17 15.3 13.6
3600
NPE 32 L4 C 120 12 18 17.2 16.5 14.9 13.2 21.8 20.8 20 18 16
4
RPM
VOLTAGE REGULATOR
12
All the generators on this page come ‘standard’ with the DSR AVR.
BRUSHED BRUSH COMPOUND
TWELVE WIRE
SPECIAL WINDING
STANDARD WINDING
DEDICATED WINDING
G BROAD VOLTAGE
VOLTAGE REGULATOR
12
All the generators on this page come ‘standard’ with the DSR AVR.
BRUSHED
TWELVE WIRE
SPECIAL WINDING
BRUSHLESS ELECTRONIC BR
STANDARD WINDING
DEDICATED WINDING
34 | www.meccalte.com
Totally Enclosed Alternators
50 60
HERTZ HERTZ
kVA @ 50Hz Temp. Rise/Amb. C/ 0.8PF
115 / 200 / 230 / 400 V
OLE 4 POLE
MODEL WEIGHT (kg) LEADS AVR 125/40 105/40 80/40 95/50
TE34-1S/4 310 12 UVR6 50 45 40 42
50
60 400 TE34-2S/4 376 12 UVR6 60 54 48 50
POLE 6 POLE
HERTZ HERTZ
TE34-1L/4 396 12 UVR6 70 63 56 58
TE34-2L/4 430 12 UVR6 80 72 64 67
3 ph
THREE PHASE
kVA @ 60Hz Temp. Rise/Amb. C/ 0.8PF
138 / 240 / 276 / 480 V
1500 MODEL WEIGHT (kg) LEADS AVR 125/40 105/40 80/40 95/50
1800 1500 1800
TE34-1S/4 310 12 UVR6 60 54 48 50
RPM RPM RPM
TE34-2S/4 376 12 UVR6 72 65 57.5 60
TE34-1L/4 396 12 UVR6 84 76 67 70
12 4 TE34-2L/4 430 12 UVR6 96 87 77 80
3000TWELVE WIRE
3600
3000
FOUR WIRE
3600
RPM RPM
Consult Factory for pricing.
RPM
2G DIGITAL AVR
DER2
VOLTAGE REGULATOR VOLTAGE REGULATOR
IP55
INGRESS PROTECTION
BRUSHLESS CAPACITOR
All machines have an auxiliary winding ‘standard’ with 300% short circuit capability.
UVR6/1-H400B AVR has under frequency, over voltage protection, 3ph reference; regulation is +/- 1%. BRUSH COMPOUND
BRUSH ELECTRONIC
The following accessories are available upon request for an additional charge:
Space Heaters
Temperature detectors (thermistors or PT100) for stator windings and bearings. BRUSHLESS ELECTRONIC BR
2/3 pitch windings with skewed slots for maximum reduction of harmonic content.
TOTAL+ treatment standard from HCP32 up to HCO38.
4 layers of polyester in addition to a clear varnish and EG43 overcoat on the main and exciter windings is standard
on 400 Hz machines.
36 | www.meccalte.com
2 Pole Industrial Ratings
MODEL WEIGHT (kg) AVR 125/40 105/40 %EFF 125/40 105/40 %EFF 125/40 105/40
ECP3 1S2 56 DSR 8 7.2 78.5 9.6 8.6 79.9 8.5 7
ECP3 2S2 62 DSR 10 9 80.5 12 10.8 82.8 10.5 9
ECP3 3S2 68 DSR 12.5 11 83.0 15 13 84.5 13 10.5
ECP3 1L2 80 DSR 16 14.5 84.5 19.2 17 86.1 17 14
ECP3 2L2 88 DSR 20 18 85.5 24 21,5 87.2 21 18
ECP28 M2 A 126 DSR 22 20 85.2 26.5 24 86.2 22 20
ECP28 2L2 A 136 DSR 27 25 86.4 32.5 30 87.9 27 24.5
ECP28 3L2 A 141 DSR 31.5 30 87.2 38 36 89.2 32 30
ECP28 VL2 A 156 DSR 40 37 87.8 48 44 89.7 40 37.5
ECP32 2S2 A 173 DSR 44 40 87.4 53 48 89.2 46 41.5
ECP32 3S2 A 199 DSR 55 50 88.1 66 60 89.5 58 52.5
ECP32 1L2 A 214 DSR 66 60 88.4 79.5 72 90.2 68 61.5
ECP32 2L2 A 231 DSR 82 75 89.0 98.5 90 90.5 84 76
ECP34 1S2 A 334 DSR 100 90 90.0 120 108 91.8 105 95
ECP34 2S2 A 403 DSR 125 113 90.7 150 135 92.2 130 120
ECP34 1L2 A 446 DSR 156 140 91.2 187 169 92.8 160 145
ECP34 2L2 A 482 DSR 170 154 91.8 208 188 93.5 175 160
ECO38 1S2 A 510 DSR 158 142 91.7 188 169 93.1 163 150
ECO38 1L2 A 676 DSR 208 188 92.2 250 225 93.5 215 197
ECO38 2L2 A 790 DSR 300 270 92.8 360 324 93.9 315 288
1500
HERTZ
S16W-75 14.3 2.5 74 3 74.6
S16W-90 16.1 3.5 75 4.2 75.6 1800
S16W-105 17.7 4.1 76 4.9 76.6 1 RPM
ph
BRU
Above machines are brushless with capacitior control and optional AVR.
BRUSH COMPOUND
BRUSHED B
2 Pole | 1Phase (AVR) kVA @ 1.0 PF, 50Hz kVA @ 1.0 PF, 60Hz
DIGITAL
MODEL WEIGHT (kg) 115/230 V %EFF 120/240 V %EFF
ES16W-75 HD 15.6 2.3 73.7 2.7 74.2
VOLTAGE REGULATOR
BRUSHLESS ELECTRONIC BRUSHLESS COMPOUND
BRUSHLESS ELECTRONIC BRU
38 | www.meccalte.com
2 Pole Portable Ratings Three Phase
THREE PHASE
2 Pole | 3Phase (AVR) kVA @ 0.8 PF, 50Hz kVA @ 0.8 PF, 60Hz
3000 MODEL WEIGHT (kg) 230/400 V %EFF 277/480 V %EFF
3600
3000 3600
ET16F-130 30 5.5 80.2 6.6 80.6
RPM RPM RPM
2G DIGITAL AVR
BRUSHED
DER2
BRUSH COMPOUND
BRUSH COMPOUND
BRUSHED BRUSH COMPOUND
50Hz Connections
The following are the most common connection arrangements utilized with Mecc Alte generators. Always verify that
the connections of all the leads from the main stator are consistent with the nameplate voltage required. Connection
diagrams are supplied with every generator and should be used as the primary source of information. Please consult
the factory for any questions regarding these connections.
60 2
1
L1 L1–L2–L3: 400V 3ø
L1–L2: 400V
L1–L3: 400V
L2–L3: 400V L-L 380 400 415 440 760 800 830 880 50
N–L1: 230V
Series Star
HERTZ
4
3
N
N–L2: 230V
N–L3: 230V
HERTZ
12
11 8
10
L3
9 7
6 L2 400 VOLT, 3PHASE
L-N 220 230 240 254 440 460 480 508
5
50 L1–L2–L3: 200V 3ø
60 400 1
L1
3
L1–L2: 200V
L1–L3: 200V
L2–L3: 200V
N–L1: 115V
L-L 190 200 208 220 380 400 415 440
HERTZ Parallel Star
HERTZ N
N–L2: 115V
N–L3: 115V
2 4
12 6
L3
11 10 8
7
5
L2
200 VOLT, 3PHASE L-N 110 115 120 127 220 230 240 254
9
115 VOLT, 1PHASE
L1 L1–L2–L3: 230V 3ø
L1–L2: 230V
12 1 L1–L3: 230V
L2–L3: 230V L-L 220 230 240 254 440 460 480 508
11 2 M–L1: 115V
M
Series Delta 10 3
M–L2: 115V
9 4 230 VOLT, 3PHASE L-M 110 115 120 127 220 230 240 254
L3 8 7 6 5 L2 115/230 V OLT, 1PHASE
L1 L1–L2–L3: 115V 3 ø
L1–L2: 115V
L1–L3: 115V
10 1 L2–L3: 115V
12 3
Parallel Delta L-L 110 115 120 127 220 230 240 254
9 11 4 2
8 7
115 VOLT, 3PHASE
L3 6 5 L2 115 VOLT,1PHASE (L1-L2)
L1–L2–L3: 346V 3 ø
L1 1 L1–L2: 200V
2
12
L1–L3: 200V
L2–L3: 200V
L-L 330 346 360 380 660 690 720 760
N
Zig-Zag (*) 7
11 L2
8 3 5
10
46
346 VOLT, 3PHASE L-N 191 200 208 220 380 400 415 440
L3 9 200 VOLT,1PHASE (L1-L2)
L1–L2: 230V
9 M–L1: 115V
8
6 11 M–L2: 115V L-L 220 230 240 254 440 460 480 508
Single Phase 7 10
5 12
Parallel Zig-Zag 2 1
L2 M L1
4 3
L-M 110 115 120 127 220 230 240 254
115/230 VOLT, 1PHASE
L1–L2: 230V
8 11 6 9 M–L1: 115V
M–L2: 115V L-L 220 230 240 254 440 460 480 508
Single Phase 12
7 5 10
Double Delta
L2 4 3 2 1 L1
(**) M L-M 110 115 120 127 220 230 240 254
115/230 VOLT, 1PHASE
In case of single phase load, it is important that the phase current does not exceed the nominal value.
(*) Rated power must be multiplied by 0.866.
(**) Half of rated power is obtainable when connecting between L1-M or L2-M.
40 | www.meccalte.com
Wiring Connection Diagram
60Hz Connections
The following are the most common connection arrangements utilized with Mecc Alte generators. Always verify that
the connections of all the leads from the main stator are consistent with the nameplate voltage required. Connection
diagrams are supplied with every generator and should be used as the primary source of information. Please consult
the factory for any questions regarding these connections.
60 2
1
L1 L1–L2–L3: 480V 3ø
L1–L2: 480V
L1–L3: 480V
L2–L3: 480V L-L 415 440 460 480 830 880 920 960
N–L1: 277 V
HERTZ
Series Star 4
3
N
N–L2: 277 V
N–L3: 277 V
12
11 8
10
L3
9 7
6 L2 480 VOLT, 3PHASE
L-N 240 254 266 277 480 508 530 554
5
L1–L2–L3: 240V 3ø
400 1
L1
3
L1–L2: 240V
L1–L3: 240V
L2–L3: 240V
N–L1: 139V
L-L 208 220 230 240 415 440 460 480
HERTZ Parallel Star N
N–L2: 139V
N–L3: 139V
2 4
12 6
L3
11 10 8
7
5
L2
240 VOLT, 3PHASE L-N 120 127 133 139 240 254 266 277
9 139 VOLT, 1PHASE
L1 L1–L2–L3: 277V 3ø
L1–L2: 277V
12 1 L1–L3: 277V
L2–L3: 277V L-L 240 254 266 277 480 508 530 554
11 2 M–L1: 139V
M
Series Delta 10 3
M–L2: 139V
9 4 277 VOLT, 3PHASE L-M 120 127 133 139 240 252 266 277
L3 8 7 6 5 L2 139/277 VOLT, 1PHASE
L1 L1–L2–L3: 139V 3 ø
L1–L2: 139V
L1–L3: 139V
10 1 L2–L3: 239V
12 3
Parallel Delta L-L 120 127 133 139 240 252 266 277
9 11 4 2
8 7
139 VOLT, 3PHASE
L3 6 5 L2 139 VOLT,1PHASE (L1-L2)
L1–L2–L3: 415V 3 ø
L1 1 L1–L2: 240V
2
12
L1–L3: 240V
L2–L3: 240V
L-L 359 380 400 415 720 760 800 830
N
Zig-Zag (*) 7
11 L2
8 3 5
10
46
415 VOLT, 3PHASE L-N 207 220 230 240 415 440 460 480
L3 9 240 VOLT,1PHASE (L1-L2)
L1–L2: 277 V
9 M–L1: 139V
8
6 11 M–L2: 139V L-L 240 254 266 277 440 460 480 554
Single Phase 7 10
5 12
Parallel Zig-Zag 2 1
L2 M L1
4 3
L-M 120 127 133 139 220 230 240 277
139/277 VOLT, 1PHASE
L1–L2: 277 V
8 11 6 9 M–L1: 139V
M–L2: 139V L-L 240 254 266 277 440 460 480 554
Single Phase 12
7 5 10
Double Delta
L2 4 3 2 1 L1
(**) M L-M 120 127 133 139 220 230 240 277
139/277 VOLT, 1PHASE
In case of single phase load, it is important that the phase current does not exceed the nominal value.
(*) Rated power must be multiplied by 0.866.
(**) Half of rated power is obtainable when connecting between L1-M or L2-M.
2 447,7 (17 5/8) 466,7 (18 3/8) 489 (19.25) 12 M10 (3/8)
3 409,6 (16 1/8) 428,6 (16 7/8) 451 (17.75) 12 M10 (3/8)
4 362 (14.25) 381 (15) 403 (15 7/8) 12 M10 (3/8)
5 314,3 (12 3/8) 333,4 (13 1/8) 356 (14) 8 M10 (3/8)
XG
S.A.E. Flywheel Dimensions, mm (in)
Flywheel A B C XG Holes Size
21 584,2 (23) 641,35 (25.25) 673,1 (26.5) 0 12 M16 (5/8)
18 498,5 (19 5/8) 542,35 (21 3/8) 571,5 (22.5) 15,7 (5/8) 6 M16 (5/8)
14 409,6 (16 1/8) 438,15 (17.25) 466,72 (18 3/8) 25,4 (1) 8 M12 (1/2)
A B C
11 1/2 314,3 (12.375) 333,37 (13.125) 352,42 (13 7/8) 39,6 (1 9/16) 8 M10 (3/8)
10 276,2 (10 7/8) 295,27 (11 5/8) 314,32 (12 3/8) 53,8 (2 1/8) 8 M10 (3/8)
8 225,4 (8 7/8) 244,47 (9 5/8) 263,52 (10 3/8) 62 (2 7/16) 6 M10 (3/8)
7 1/2 206,4 (8 1/8) 222,25 (8.75) 241,3 (9 1/2) 30,2 (1 3/16) 8 M8 (5/16)
6 1/2 184,2 (7.25) 200 (7 7/8) 215,9 (8 1/2) 30,2 (1 3/16) 6 M8 (5/16)
42 | www.meccalte.com
Mecc Alte SpA (HQ) Mecc Alte Portable Mecc Alte Power Products srl Zanardi Alternatori srl
Via Roma Via A. Volta Via Melaro Via Dei Laghi
20 – 36051 Creazzo 1 37038 Soave 2 – 36075 Montecchio 48/B – 36077 Altavilla
Vicenza – ITALY Verona – ITALY Maggiore (VI) – ITALY Vicenza – ITALY
T: +39 0444 396111 T: +39 0456 173411 T: +39 0444 1831295 T: +39 0444 370799
F: +39 0444 396166 F: +39 0456 101880 F: +39 0444 1831306 F: +39 0444 370330
E: info@meccalte.it E: info@meccalte.it E: info@meccalte.it E: info@zanardialternatori.it
aftersales@meccalte.it aftersales@meccalte.it aftersales@meccalte.it