Professional Documents
Culture Documents
: T-1643/2174/2022
COMMERCIAL TEST REPORT (Initial) ekg/Month : April, 2022
[ONLINE TESTING]
(यह परीक्षण ररपोर्ट 30/04/2025 तक वैध है / THIS TEST REPORT IS VALID UPTO 30/04/2025)
Hkkjr ljdkj
d`f"k ,Oka fdlku dY;k.k ea=ky;
¼d`f"k] lgdkfjrk ,oa fdlku dY;k.k foHkkx½
GOVERNMENT OF INDIA
MINISTRY OF AGRICULTURE AND FARMERS WELFARE
(DEPARTMENT OF AGRICULTURE, CO-OPERATION & FARMERS WELFARE)
1. SPECIFICATIONS
1.1 Tractor:
Make : Mahindra
Model : 415 DI XP PLUS
Brand name, if any : BHOOMIPUTRA
Type : Rear Wheel Drive, Standard Agricultural
Tractor.
Month & year of manufacture : 08/21
Chassis number : MBNGAAVKBMRE01437
Country of origin : India
1.2 Engine:
Manufacturer‟s address : M/s. Mahindra & Mahindra Limited
(Farm Equipment Sector)
Agri Business Development Center, Khatima
Panipat Highway, Udham Singh Nagar, Vil.
Lalpur, Tehsil-Kichha, Rudrapur – 263 153
Make Mahindra
:
Model MM27423AH
:
Type Four stroke, direct injection, naturally
:
aspirated, liquid cooled, diesel engine.
Serial number : RMD5FGA1054
Country of origin : India
1.2.1 Engine speed (rpm), (Manufacturer’s recommended production settings):
- Maximum speed at no load : 2150 to 2350
- Low idle speed : 750 to 850
- Speed at maximum torque : 1200 to 1500
Rated speed, (rpm):
- For PTO use : 2000
- For drawbar use : 2000
1.3 Cylinder & Cylinder Head:
Number : Four
Disposition : Vertical, Inline
Bore/stroke, (mm) : 88.9/110
Capacity as specified by the : 2730
applicant, (cc)
Compression ratio : 19.8 : 1
Type of cylinder head : Monoblock
Type of cylinder liners : Wet, replaceable
Type of combustion chamber : Re-entrant cavity on piston head
Arrangement of valves : Overhead, inline
Valve clearance (cold/hot): Cold Hot
- Inlet valve, (mm) : 0.4 0.3
- Exhaust valve, (mm) : 0.5 0.4
1.4 Fuel System:
Type of fuel feed system : Gravity and force feed
1.4.1 Fuel tank:
Capacity, ( l ) : 48.5
Location : Above clutch housing
Provision for draining of sediments/ : Provided
water
Material of fuel tank : Metallic
1 2 3 4 5 6 7
18.1.2 Drawbar performance :
a) Max. drawbar pull Minimum 70% of static 17.30
with ballasted mass of tractor with ballast. (D)
Non
corresponding to 16.73 20.21 Yes
Evaluative
15 percent wheel Minimum
slip, (kN) (R)
b) Max. drawbar pull Minimum 70% of static 12.63
without ballast mass of tractor without (D)
corresponding to Evaluative ballast or with standard 8.85 12.88 Yes
15 percent wheel ballast, as the case may (R)
slip, (kN) be. Minimum
c) Maximum Minimum 80 % of PTO power
drawbar power Evaluative as referred in Sl No. i) a) of 22.32
PTO performance in case of
without ballast, (D)
tractors having total static
(kW). mass > 1500 kg Minimum 75 23.7 Yes
23.4
% of PTO power as referred in (R)
Sl No. i) a) of PTO
Minimum
performance in case of light
weight tractors having ≤1500
kg total static mass of tractor
Minimum 75 % of the engine
power as referred in Sl No. i)
a) of engine performance in
case of tractors which do not
have a PTO shaft.
Maximum The declared value should
transmission oil not exceed the maximum
d) o Evaluative 120 (D) 78 Yes
temperature, ( C) value specified by oil
company
18.1.3 Power lift and hydraulic pump performance:
a) Maximum lifting capacity throughout the range of lift, (kN):
At hitch
1) Evaluative Tolerance of ± 10% 14.6 (D) 13.84 Yes
points
The lift capacity should at
With the least be 24 kg/PTO kW and 10.20 (D)
2) standard Evaluative it should be 21.5 kg/engine 10.89 Yes
kW where the tractor is not 6.87 (R)
frame
provided with a PTO shaft. Minimum
b) Maximum drop in
the height of the
point of
application of the
Non The observed value 50 (D)
force after each 5 Evaluative
40 Yes
should not exceed 50 mm Maximum
minutes interval
for a total
duration of 30
Minutes, (mm)
1 2 3 4 5 6 7
18.1.4 Brake performance at 25 kmph:
a) Maximum stopping distance at a force, equal to or less than 600 N on brake pedal with
road ballast, (m):
1) Cold brake Evaluative 10 10 (R) 6.38 Yes
2) Hot brake Evaluative 10 10 (R) 6.36 Yes
b) Maximum force exerted on 170
the brake pedal to achieve a 600 (R)
2 Evaluative 600 to Yes
deceleration of 2.5 m/s , (N) Maximum
206
c) Whether parking brake is
effective at a force of 600 N at Evaluative Yes / No Yes Yes Yes
foot pedal (s) or 400 N at
hand lever
18.1.5 Noise measurement :
a) Maximum ambient noise As per
Evaluative 88 (R) 84 Yes
emitted by the tractor, dB(A) CMVR
b) Maximum noise at operator‟s As per
Evaluative 96 (R) 92 Yes
ear level, dB(A) CMVR
18.1.6 Amplitude of mechanical vibrations at:
1) Left foot rest 144 No
2) Right foot rest 100 188 No
100
Non Evaluative microns
3) Seat (with driver seated) (R) 152 No
(max.)
4) Steering wheel 268 No
18.1.7 Air cleaner:
Maximum air cleaner oil pull Evaluative 0.25 0.25 0.09 Yes
over, (%) (Max.) (Max.)
18.1.8 Haulage requirements:
a) Gross mass of the trailers, (tonne):
Two wheel Non
As specified 5.0 (D) 5.0 Yes
Evaluative
by the
Four wheel Non manufacturer 7.0 (D) 7.0 Yes
Evaluative
b) Distance travelled / liter of fuel consumption, (km/l):
Two wheel 6.57 No
Non 5.0
to 6.0 (D)
to
Evaluative As specified
6.78
by the
Four wheel manufacturer
5.0 5.82
Non
to 6.0 to No
Evaluative
(D) 6.09
c) Fuel consumption, (ml/km/tonne):
Two wheel 30 to 35 29.50
Non
(D) to No
Evaluative As specified
30.46
by the
Four wheel manufacturer
25 to 30 23.49
Non
(D) to No
Evaluative
24.52
1 2 3 4 5 6 7
18.1.9 Wetland cultivation :
Sealing for the Evaluative The identified
following assemblies: assemblies should
1) -do- essentially meet the There
Clutch
requirement of IS: should be
assembly 11082. No water No ingress of
2) Brake -do- no
ingress in the
ingress of water and/or
housings identified assembly mud was
given in column-2. If water
3) Front axle -do- and/or observed Yes
tractor does not
hubs meet the mud (R)
4) Engine Oil -do- requirements of
5) Transmission -do- wetland cultivation,
it may be
Oil recommended for
dry land operation
only.
18.1.10 Safety features :
a) Guards against Belt drives, pulleys, silencer, Meets the
moving and hot Evaluative hydraulic pipes (As per IS requirement Yes
parts 12239 (Part2)
b) Lighting Meets the
Evaluative As per CMVR Yes
arrangement requirement
c) Seating requirements Should meet the requirements Does not No
(Tractors having more Non of IS: 12343 (As amended meet the
than 1150 mm rear Evaluative from time to time)
requirement
track width)
d) Technical Should meet the requirements Meets the Yes
requirements for Evaluative of IS: 4931 (As amended from requirement
PTO shaft time to time)
e) Dimensions of three Should meet the requirements Meets the Yes
Non
point linkage of IS: 4468 (Part-I) (As requirement
Evaluative
amended from time to time)
f) Specifications of Should meet the requirements Meets the Yes
linkage drawbar Evaluative of IS: 12953 (As amended requirement
from time to time)
g) Swinging drawbar Evaluative Should meet the requirement Not provided Not
(wherever fitted) of IS: 12362 (Part 3) (As appli-
amended from time to time) cable
h) 1) Maximum Evaluative Should not exceed 11.87 Yes
travelling 20 Kmph (Meets the
speed at rated requirement)
engine speed
in reverse
gears, Kmph
2) Audible Evaluative As soon as the travelling Not fitted Not
warning signal speed in reverse gear reaches appli-
on tractor to 20 kmph, an audible cable
warning signal on tractor shall
be activated. The safety
aspects about the operation of
shuttle technology shall be
brought in operation and
manufacturer /dealer shall
ensure the training on this
aspect to operator before the
delivery of tractor.
1 2 3 4 5 6 7
18.1.11 Labelling of tractors (Provision of labelling plate):
1) Make Evaluative Should conform to Mahindra Yes
2) Model Evaluative the requirements of 415 DI XP PLUS Yes
3) Month & Evaluative CMVR along with 08/21
maximum PTO Power
Year of in kW and year of
Yes
manufacture manufacture in
4) Engine Evaluative numerical form. RM05FGA1054 Yes
number MM YY
5) Chassis Evaluative MBNGAAVKBMRE01 Yes
number Digit 01 – 12 in box 437
No.1
6) Maximum Evaluative 27.9 Yes
for MM will represent
PTO power, the months and next
(kW) two digits in box No.2
for YY
will represent the year
of
Manufacturing.
18.1.12 Discard limit for:
(a) Cylinder bore Evaluative 88.907
89.13
diameter, (mm) to Yes
To be specified by 88.913
(b) Clearance the manufacturer
0.084
between piston & Non and supported by 0.20
to Yes
cylinder liner at Evaluative the printed literature
0.089
skirt, (mm)
(c) Piston diameter at Non 88.822
88.81
skirt, (mm) Evaluative to Yes
88.826
d) Ring end gap (mm):
- Top comp. ring. 0.30 Yes
2.5 to
To be specified by 0.35
nd
- 2 comp. ring. the manufacturer 2.5 0.30 Yes
Evaluative and supported by to
the printed literature 0.35
- Oil ring. 2.0 0.30 Yes
to
0.35
(e) Ring groove clearance (mm):
- Top comp. ring. 0.30 --Tappered-- --
- 2nd comp. ring. To be specified by 0.30 0.064 Yes
the manufacturer to
Evaluative and supported by 0.066
- Oil ring. the printed literature 0.20 0.045 Yes
to
0.046
(f) Clearance of main bearings (mm):
- Diametrical To be specified by 0.085
clearance Evaluative the manufacturer 0.20 to Yes
and supported by 0.091
- Crankshaft end the printed
Evaluative 0.50 0.12 Yes
float literature
1 2 3 4 5 6 7
(g) Clearance of big end bearings, (mm):
- Diametrical Evaluative -do- 0.20 0.094 to 0.099 Yes
- Axial Evaluative -do- 0.75 0.20 to 0.25 Yes
(h) Clearance
Non
between king pin -do- 0.30 0.097 to 0.106 Yes
Evaluative
and bush, (mm)
(i) Clearance between
Non
centre pin and -do- 0.30 0.096 to 0.122 Yes
Evaluative
bush, (mm)
18.1.13 Literature (Submission to test agency)
(a) Operator manual Evaluative Provided /
Provided Provided Yes
Not Provided
(b) Parts Catalogue Evaluative Provided /
Provided Provided Yes
Not Provided
(c) Workshop/ Evaluative Provided /
Provided Provided Yes
Service manual Not Provided
18.1.14 Fitment of Roll Over Protective Structures (ROPS):
For tractor having Evaluative ROPS should meet the Not
more than 1150 requirement of IS:1182 or appli
Not fitted cabl
mm rear track OECD code or equivalent
width International Standard e
18.1.15 Standard Evaluative Trailer hitch, front tow
Accessories hook, linkage drawbar Provided Yes
should be provided with
tractor
18.1.16 Accessories Non Ballast weight, if fitted,
(optional) Evaluative should meet the Provided Yes
requirement of CMVR
ANNEXURE- I
BRIEF SPECIFICATION OF MATCHING IMPLEMENTS AS DECLARED BY APPLICANT
S. No. Parameters Disc Plough Rotavator Puddler
1 Make Farmking Mahindra Not available
2 Type Mounted Mounted Mounted
3 No. of Discs / Blades Two 30 in 5 12 (6 in 2 gangs)
flanges
4 Type of Discs / Blades Plain concave Hatchet Notched
5 Size of Discs / Blades, (mm) 655 220 x 75 x 7 460
6 Spacing of Discs /Flanges, (mm) 495 240 165
7 Lower hitch point span, (mm) 760 800 680
8 Mast height, (mm) 480 640 500
9 Overall Dimensions, (mm):
Length 1480 970 1190
Width 1060 1510 1810
Height 1180 1100 1330
10 Gross Mass, (kg) 200 200 240
11 Working width (cm) 2 x 30 125 210
ANNEXURE-II
BRIEF SPECIFICATION OF HALF CAGE WHEEL AS DECLARED BY APPLICANT
ANNEXURE-IIl
BRIEF SPECIFICATION OF TRAILER DECLARED AS MATCHING TRAILER BY APPLICANT
SI No. Item Trailer Trailer
1. Make Kisan Engineering Works, MIDC, Awadhan Dhule, (M.S.)
2. Model Kisan 1062 Not available
3. Type of trailer Semi - Trailer Semi – Trailer
4. Number of axles Single Double
5. Un laden Weight of Trailer, kg 1670 2800
6. Fully laden Weight of Trailer, 4000 5500
Tons (Kg)
7. Overall dimensions of Trailer, (mm):
Overall Width 1870 2140
Overall Length 4180 5785
Overall Height 2175 2110
Wheel Base Not applicable 2835
Wheel Track 1600 1740(Front) &1765(Rear)
8. Dimension of fitted Platform, (mm):
Length 3040 4225
Width 1830 2135
Height from ground 1190 1305
9. Brakes of Trailer Not Provided Not Provided
ANNEXURE-IV