You are on page 1of 410

Construction of Mass Rapid Transit Jakarta

Contract Package CP101

Lebak Bulus Station


Structural Design
(Foundations)

TWJO-1-TCD-ST1-0004-Rev A

TOKYU-WIKA JOINT OPERATION

When viewed in ACONEX this document is Controlled, this means:


1. Distribution is centralized - in this case through ACONEX. Any improvement suggestions should be
forwarded to the Quality Manager.
2. Each copy is issued to a particular person or organization.
3. Copy holders will be automatically issued with any amendments through ACONEX.
4. Photocopies of this document are uncontrolled and users should confirm validity in ACONEX prior to
use.
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

DOCUMENT/DRAWING TECHNICAL
VERIFICATION AND REVISION RECORD

PROJECT NAME Jakarta MRT


PROJECT NO. AECOM 60313051 FILE 1800
*DOC/DWG NO. AECOM-1-TCD-ST1-0004 DATE OF FIRST ISSUE 17-10-2014
*DOC/DWG TITLE Cipete Raya Station – Foundation Design - Pile
ISSUE/REV.

APPROVED
PREPARED
/DESIGNED

CHECKED
DATE OF
REV. No.

DESCRIPTION

- 17-10- Initial Submission SG NB IDJ


2014
1 12-12- Change in column location at grade SG NB IDJ
2014
2 29-12- Revised as per JO & 3PDV comments SG NB IDJ
2014

* Delete as Appropriate

TWJO-1-TCD-ST1- 0004-Rev A
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

CONTENTS

1. INTRODUCTION ............................................................................................................ 1
1.1 Scope of Report........................................................................................................ 1
1.2 Design Package Affiliation ........................................................................................ 1
2. DETAILED DESCRIPTION – LEBAK BULUS STATION .............................................. 2
2.1 Description of structure ............................................................................................. 2
2.2 Structural modelling .................................................................................................. 5
2.2.1 General ......................................................................................................... 5
2.2.2 Methodology.................................................................................................. 6
2.3 Loadings ................................................................................................................... 7
2.3.1 Dead Load..................................................................................................... 7
2.3.2 Super imposed Dead Load ............................................................................ 9
2.3.3 Live Load .................................................................................................... 10
2.3.4 Braking & Traction Load .............................................................................. 11
2.3.5 Temperature Load ....................................................................................... 12
2.3.6 Wind effects ................................................................................................ 12
2.3.7 Seismic Loadings ........................................................................................ 13
2.4 Load Combinations..................................................................................................16
3. STRUCTURAL ANALYSIS ...........................................................................................17
3.1 Seismic Response of structure ................................................................................17
3.2 Mode Shapes ..........................................................................................................17
3.3 Fundamental Time period ........................................................................................19
3.4 Seismic mass participation ......................................................................................19
3.5 Lateral Seismic Inter-storey drift ..............................................................................19
4. SUBSOIL CONDITIONS ...............................................................................................26
4.1 Stratification.............................................................................................................26
4.1.1 Stratum 1: Alluvial Fan (Unit Qav) ............................................................... 26
4.1.2 Stratum 2: Bojongmanik Formation (Unit Tmb) ............................................ 26
4.2 Groundwater Conditions ..........................................................................................27
4.2.1 Borehole Reference .................................................................................... 27
4.3 Reduction of Soil Properties due to Cyclic Loading ..................................................27
4.3.1 Reduction of Undrained Shear Strength ...................................................... 27
4.3.2 Reduction of Soil Stiffness ........................................................................... 27
4.4 Subsoil Properties ...................................................................................................29

TWJO-1-TCD-ST1- 0004-Rev A
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

5. SITE SPECIFIC RESPONSE ANALYSIS .....................................................................30


5.1 Earthquake Ground Motion at Bedrock ....................................................................30
5.2 Correlation of Shear Wave Velocity (Vs) to SPT-N Value ........................................30
5.3 Site Zoning ..............................................................................................................30
5.4 Site Specific Response Spectra Result ....................................................................32
6. PILE BEARING CAPACITY ..........................................................................................33
6.1 Factor of Safety .......................................................................................................33
6.2 Bearing Capacity Analysis .......................................................................................33
6.2.1 Axial Bearing Capacity ................................................................................ 33
6.3 Design Parameters for Axial Bearing Capacity ........................................................34
6.4 Pile Group ...............................................................................................................35
6.4.1 Spacing of Piles........................................................................................... 35
6.4.2 Block Failure Analysis ................................................................................. 35
6.5 Result of Analysis ....................................................................................................36
7. LATERAL DEFLECTION OF PILE ...............................................................................37
7.1 Allowable Lateral Displacements .............................................................................37
7.2 Pile Model and Soil-Structure-Interaction .................................................................37
7.3 Design Parameters for Lateral Soil Capacity and Stiffness ......................................37
7.3.1 Lateral Capacity of Soils .............................................................................. 37
7.3.2 Horizontal Subgrade Modulus ..................................................................... 38
7.4 Pile Group ...............................................................................................................38
7.4.1 Spacing of Piles........................................................................................... 38
7.4.2 Group Effect ................................................................................................ 38
8. Design of Foundation..................................................................................................39
8.1 Bored Pile Design ....................................................................................................39
8.2 Bored Pile Design ....................................................................................................42
8.2.1 Summary of Section Analysis ...................................................................... 43
8.2.2 Typical reinforcement section ...................................................................... 43
8.3 Structural Design of Pile Cap ...................................................................................44
8.3.1 Lateral deflection of pile cap top .................................................................. 45
9. SETTLEMENT OF PILES .............................................................................................47
9.1 Settlement Limit .......................................................................................................47
9.2 Pile Settlement Analysis ..........................................................................................47
9.3 Group Pile Settlement .............................................................................................47
9.4 Consolidation Settlement .........................................................................................48

TWJO-1-TCD-ST1- 0004-Rev A
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

9.5 Result of Analysis ....................................................................................................48


10. CONCLUSION ........................................................................................................53
11. REFERENCES ........................................................................................................54

APPENDICES
Appendix A : Geological Profile at CP102 Cipete Raya Station
Appendix B : Site Zoning and SPT-N Design Line
Appendix C : Pile Schedule
Appendix D : Calculation Sheet for Pile Axial Bearing Capacity
Appendix E : Summary of pile Settlement
Appendix F : List of Relevant Drawings
Appendix G : List of Reference Drawings
Appendix H : List of standards & codes
Appendix I : Loading Plan Drawing
Appendix J : Design Calculation of Pile & Pile Cap

List of Tables
Table 1 - Design Package Affiliation ...................................................................................... 1
Table 2 – Summary of Load Combinations ...........................................................................16
Table 3 – STAAD mass participation table ...........................................................................17
Table 4 – Drift Displacements from STAAD and amplified values in longitudinal direction ....20
Table 5 – comparison of displacements with inter-storey drift limits ......................................21
Table 6 – Drift Displacements from STAAD and amplified values in Transverse direction ....23
Table 7 – comparison of displacements with inter-storey drift limits ......................................24
Table 8 - Recommended Geotechnical Design Parameters .................................................29
Table 9 - List of published studies on Vs to SPT-N correlations............................................30
Table 10 - Site Zoning ..........................................................................................................30
Table 11 - Minimum Factor of Safety for Design ...................................................................33
Table 12 - Bored Pile Design Parameters* ...........................................................................34
Table 13 - Summary of Design Pile Length ..........................................................................40
Table 14 – Typical axial loads & moments for pile design.....................................................42
Table 15 – Typical analysis results of pile design .................................................................43
Table 16- Design moments in Pile Cap ................................................................................44
Table 17 – Stress Check from OASYS .................................................................................44
Table 18 – Recommended Allowable Settlement for Buildings*............................................47
Table 19 – Summary of Pile Settlement ...............................................................................49

List of Figures
Figure 1 – Typical section at the pier location of entire station ............................................... 2
Figure 2 – Typical platform layout of station. ......................................................................... 2
Figure 3 – Typical Section of Box Girder with Rail Plinth & Rolling Stock .............................. 3
Figure 4 – Typical Section at pier location supporting viaduct & precast girders. ................... 3
Figure 5 – Typical Plan at pier location supporting viaduct & precast girders ......................... 3
Figure 6 – Typical Elevation at pier location supporting viaduct & precast girders ................. 4
Figure 7 – Concourse floor layout of Lebak Bulus Station ..................................................... 4

TWJO-1-TCD-ST1- 0004-Rev A
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 8 – Column Layout at Ground Level ........................................................................... 5


Figure 9 – Beam Frame layout at Concourse Level ............................................................... 5
Figure 10 – Structural Design Model ..................................................................................... 6
Figure 11 - Envelop Curve of Load-Displacement Relation of Reinforced Concrete Members (under
low axial force) ......................................................................................................................13
Figure 12 – Comparison of ODE Design Spectrum ..............................................................15
Figure 13 – Comparison of MDE Spectrum ..........................................................................15
Figure 14 – Mode Shape 1 – Transverse Translation ...........................................................17
Figure 15 – Mode Shape 2 – Ineffective participation ...........................................................18
Figure 16 -Mode Shape 3 – Longitudinal Translation ..........................................................18
Figure 17 - Soil stratification .................................................................................................28
Figure 18 - Layout of Site Zoning .........................................................................................28
Figure 19 - Design shear wave velocity profiles for each zone. ............................................31
Figure 20 - Zoning for site specific response analysis ..........................................................31
Figure 21 - Design Spectra for ODE case.............................................................................32
Figure 22 - Design Spectra for MDE case ............................................................................32
Figure 23 – Bearing capacity factor (after Meyerhof) and shape factor (Meyerhof-Skempton
.............................................................................................................................................35
Figure 24 – Pile-Soil Model (after Reese and O’Neill, 1988) .................................................37
Figure 25 – Idealized variation of limiting resistance with depth (after Fleming et al, 2009) ..38
Figure 26 – Typical reinforcement section of piles ................................................................43
Figure 27 – Typical Pile cap schematic diagram ...................................................................44
Figure 28 – Pile-raft foundation to estimate load distribution for consolidation settlement
analysis, if applicable (Das, 2011) ........................................................................................48
Figure 29 – Contour of Pile Settlement .................................................................................51

TWJO-1-TCD-ST1- 0004-Rev A
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

1. INTRODUCTION
The proposed rail based Jakarta Mass Rapid Transit (MRT) will consist of South-
North and East West Corridors. The construction of the South-North Corridor will be
completed in two stages. Stage 1 will be carried out to connect Cipete Raya with
Bunderan HI which comprises 15.7km of twin track rails, of which 4.8km passes
through twin tunnels with the remainder supported on elevated viaducts. There are
13 stations in total, of which 6 are underground, including a fully functional depot
covering approximately 8.3 hectares. Stage 2 will expand the South-North corridor
from Bunderan HI to Kampung Bandan.
Stage 1 of the project is divided into six civil contract packages (CP), in which
CP101 to CP103 are elevated sections and CP104 to CP106 are underground
section. There are two other contract packages; CP107 for the track work and
CP108 for the rolling stock.
CP101 and CP102 are the contract packages relevant to the elevated sections.
These comprise three elevated stations (lebak bulus, Fatmawati and Cipete Raya),
a depot, approach structures and a viaduct structure of approximately 5.95 km,
which stretches from chainage -0K576m714 to +5K369m249. From the depot at
Jalan Pasar Jumat, the alignment follows Jalan Kartini and Jalan Cipete Raya to the
north and towards the contract boundary with CP103 at the southern end of Haji
Nawi Station.

1.1 Scope of Report

This report describes the structural and geotechnical design methodology of the
foundations for the Lebak Bulus Station of CP101 contract package.
The design of following structural elements is covered in this report
 Bored Pile Foundation for Lebak Bulus Station
 Pile Cap reinforcement design for Lebak Bulus Station.

1.2 Design Package Affiliation


The following table shows the relationship of this package to other design packages
of Lebak Bulus Station. Design packages of CP101 and CP102 are divided into
segments in accordance with Appendix 22 of Employer’s Requirement.
Table 1 - Design Package Affiliation
Design Design Design Package
Design Package Description
Segment Elements Number
AECOM-1-TCD-ST1- Lebak Bulus Station - Structural Design
Geotechnical
0004 (Foundations) 1/T/STN/DCS/DR/1010
LEBAK Lebak Bulus Station - Structural Design
Civil & AECOM-1-TCD-ST1-
BULUS (Station Superstructure)
Structures 0009
STATION 1/T/STN/DCS/DR/1011
Civil & AECOM-1-TCD-ST1- Lebak Bulus Station - Structural Design
Structures 0010 (Entrances) 1/T/STN/DCS/DR/1012

TWJO-1-TCD-ST1-0004-Rev A Page 1/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

2. DETAILED DESCRIPTION – LEBAK BULUS STATION

2.1 Description of structure


Lebak Bulus Station is a side platform station at chainage Km 0+330. The typical
section of the station is 22.3m wide x 20.7m high. The length of station is divided by
16 equal bays of 12.5m each making the station approximately 200m long.

Figure 1 – Typical section at the pier location of entire station

Figure 2 – Typical platform layout of station.


At the rail level, the station structure consists of the main viaduct box girders
carrying the railway tracks. The typical spans of these box girders are 25m and it is
envisaged that a shallower depth of 1.6m of box girder can be used in the station
area. The box girder would have similar shape as the rest of the viaduct box girder
so as to use the same outer form. However, the end section shall have a typical half
joint thereby changing the detail of end segment. The end segment is further also
proposed to be a complete solid concrete section to ensure the shearing capacity at
the reduced depth location.

TWJO-1-TCD-ST1-0004-Rev A Page 2/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 3 – Typical Section of Box Girder with Rail Plinth & Rolling Stock
The platform level is supported via a cross pier head protruding from the main pier.
It is proposed that the tracks be made independent from the platform in order to
avoid continual vibrations being transferred to the main frame of station. This cross
arm pier head shall support precast girders as shown in the section below on both
sides.

Figure 4 – Typical Section at pier location supporting viaduct & precast girders.

Figure 5 – Typical Plan at pier location supporting viaduct & precast girders

TWJO-1-TCD-ST1-0004-Rev A Page 3/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 6 – Typical Elevation at pier location supporting viaduct & precast girders
The platform slab shall be supported over these precast girders. The precast girders
are currently proposed with I sections and shall support the platform hollow core
slab and a 75mm concrete topping to provide in for a diaphragm type action in the
transverse direction. Further, the precast girders are proposed to be supported on
temporary steel work as shown in the above picture. Thereafter the central core
between the two girders & above the cross pier head shall be cast in cast – in – situ
concrete to provide a continuous junction. The reinforcement for negative moment
at this location shall be provided in the top 270mm cast – in – situ concrete.
A main concourse level is proposed beneath the main box girder to carry the
services pertaining to the station. The width of concourse is 22.3m. The columns
from concourse level to platform level only run on grid A & C of station as shown in
figure below.

Figure 7 – Concourse floor layout of Lebak Bulus Station


These columns are eccentric from the main columns from ground level by around
1.65m from C/L. Due to very limited vertical clearance a maximum of 2.5m
clearance below the box viaduct could have been possible. However, the areas on
both sides of box viaduct possess a structural clearance of at least 3m. Refer the
section below.
At the concourse to ground level, the column spacing in the direction of the viaduct
is in general 12.5m except at Grid no. 13 & 14 where the piers have been located in
such a way to avoid the road intersection underneath.

TWJO-1-TCD-ST1-0004-Rev A Page 4/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 8 – Column Layout at Ground Level


In the transverse direction, the main beam frames into the viaduct columns as well
as the column between 2 viaduct columns spanning in the entire width of station.
This framing forms a rigid frame in the transverse direction of the viaduct.

Figure 9 – Beam Frame layout at Concourse Level


At the concourse level, cast – in – situ secondary beams support the cast – in – situ
slab to provide a proper diaphragm action in both longitudinal & transverse direction.
The main concourse is further supported on three longitudinal rows of columns
equally spaced at 9.5m in transverse direction. The columns on the outer grids are
smaller and have been kept with a size of 1m X 1m whereas the columns on the
centre line are alternatively of 2m X 2m & 1m X 1m in cross section. The smaller
columns only rise till the concourse slab whereas the larger columns further rise to
support the viaduct at a grid spacing of 25m.
All the columns are supported by bored piles over a pile cap. The details
arrangements of pile & pile cap are the part of the second part of this report.
The overhead covering roof shall be a steel roof structure supported on the columns
rising up from concourse level
2.2 Structural modelling
2.2.1 General
Extensive computer modeling was carried out to assess the action effects in the
foundation elements. Software STAAD Pro V8i was used for analysis of elevated
station. Complete model of elevated station including superstructure, substructure
and foundations were modelled in software to accurately capture the behavior of
viaduct structure under loads. The model was made accurately with exact dimension
so that the effect of boundary conditions is modelled correctly.
The following figure shows a snapshot of a typical model in STAAD Pro used for
analysis of elevated stations..

TWJO-1-TCD-ST1-0004-Rev A Page 5/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 10 – Structural Design Model


2.2.2 Methodology
Structural elements of the station were modeled with their true material and section
properties. For the normal loading conditions a linear-elastic model was used to
assess the effect of the forces.
The lateral soil interaction with the pile structure is modelled as lateral soil springs.
The first soil spring was modelled at 1m below the pile cap bottom & 50% of the
spring value was applied at pile cap bottom node to account for the passive earth
resistance of the pile cap.
Under Seismic loading conditions, a linear-elastic dynamic analysis was used to
assess the response of the structure to the response spectrum under Operating
Design Earthquake (ODE) and Maximum Design Earthquake (MDE). The response
spectrum of the ODE and MDE is described in section 2.3.7. Directional
combinations of the earthquake motions were taken into account with in accordance
with EN1998-2 requirements. Cracked section properties (based on
recommendation of ACI 318 – 2011) were used to assess the deformation under
ODE & MDE conditions.

TWJO-1-TCD-ST1-0004-Rev A Page 6/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

2.3 Loadings
The basic loads & load combinations as defined in design manual have been
described and compared with relevant counterparts of Indonesian standard and it is
described that by adhering to the design manual parameter & EC8 guidelines a
conservative design has been envisaged.
2.3.1 Dead Load
The dead load of structure from various components can be described as follows:

a) Dead Load of 25m Box Girder ( Within Station)


Span C/C 25 m
Track beam width 1 m
Exp. Gap 0.025 m assumed
Area (m2) Length (m) No.
Segment type 1 7.16 1.975 2 both side
Segment type 2 5.07 5 2 both side
Segment type 3 4.68 10 1

Hence Weight 2.55 T/m3 = 330.69 Tonnes


3310 kN

b) Dead Load from Either Span of Viaduct (At Station/Viaduct Interface)


Pier no C16 Grid 1 Span 20.4m
DL from Viaduct 135.8443 Tonnes
DL from Station 165.3446 Tonnes
Total DL 301.1888 Tonnes
3011.888 kN
Pier no C30 Grid 15 Span 40m
DL from Viaduct 255.2717 Tonnes
DL from Station 165.3446 Tonnes
Total DL 420.6163 Tonnes
4206.163 kN

c) Dead Load from Hollow Core slab


Load of this slab is applied as point load in STAAD model
From the typical drawings of hollow core slab, the slab measured 1.196m for each
segment.
In longitudinal direction, span is 12.5m from column to column.
For approximately 8.15 m span in transverse section it comes 7 segments.
Cross sectional area of 1 segment = 0.23 m2
Total Cross sectional area of hollow core slab = 1.61 m2
Volume of hollow core slab = 20.125 m3
Total self-weight of hollow core slab = 503.125
Loads are applied at 12.5m apart in longitudinal direction
as nodal load at either side.
Load applied at intermediate support = 251.5625 kN
Load at end support = 125.7813 kN

TWJO-1-TCD-ST1-0004-Rev A Page 7/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

d) Dead Load of Stair Case


Width of staircase = 1.8 m
Riser = 0.168 m
FF thickness = 0.1 m
Waist slab thickness = 0.15 m
Weight of = 6.75 kN/m2
Steps = 3.78 kN/m2
Finishing = 4.32 kN/m2
Railing = 0.5 kN/m2

Total Load of staircase = 15.35 kN/m


LL of staircase = 9 kN/m
Width of escalator = 1.55 m
Escalator Live Load = 7.75 kN/m
Lift Load of 50kN is assumed for the analysis

e) Dead Load of wall and Slab


Slab Load Calculation
Slab Thickness = 125 mm
Self- Weight of Slab 0.125 X 25 = 3.125 kN/m2
Wall Load Calculation
Wall Thickness = 200 mm
Glazing Assumed 100mm Brick Work = 100 mm
Plaster Both Face = 20 mm
Floor Height At Platform Level = 4.2 m
Floor Height (H1) = 9.5 m
Floor Height (H2) = 7.4 m
Railing Height = 1.2 m
((Wall thickness x 20) + (2 x Plaster thickness)) * (Floor
Wall Load Calculation Height - Beam Depth)
1 m beam depth assumed for all wall load calculation.
200mm Wall Load (H1) = 42.16 kN/m
100mm Wall Load (H1) = 25.16 kN/m
200mm Wall Load(PL) = 20.832 kN/m
Glazing Load = 25.16 kN/m
200mm Wall Load (H2) = 31.744 kN/m
100mm Wall Load (H1) = 18.944 kN/m
Railing Load at periphery of PL = 3.552 kN/m
Railing Load at edges = 5.952 kN/m

TWJO-1-TCD-ST1-0004-Rev A Page 8/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

f) Dead Load of Roof Portal


For Portal, load of 0.75 kN/m2 is given in Design Manual
Self-Weight
Portal
Span Length 1 = 12.5 m
Width Measured from Architecture drawings = 27.4 m
Total Load At intermediate support = 128.4375 kN

Span Length = 12.91 m


Width Measured from Architecture drawings = 27.4 m
Total Load At end support = 132.6503 kN

2.3.2 Super imposed Dead Load


The super imposed dead load of structure from various components can be
described as follows:

a) SIDL of Track Plinth


Items Intensity
Track Panel Rail Double Track 2.13 kN/m 0.217 t/m
Fastening
Track Panel Device Double Track 0.26 kN/m 0.026 t/m
Track Panel Sleeper Double Track 6.93 kN/m 0.707 t/m
Rail Plinth/Road 0.853 m2 for
Bed Area one plinth 42.65 kN/m 4.348 t/m
Duct Trough 2 170.00 kg/m 0.170 t/m
Cable 2 17.40 kg/m 0.017 t/m
Cable 3 17.40 kg/m 0.017 t/m
5.5027 t/m
55.027 kN/m
SIDL per
Rail = 13.7566 kN/m

b) SIDL from Either Span of Viaduct (At Station/Viaduct Interface)


Pier no C16 Grid 1 Span 20.4m
SIDL Loading 9 Tonne/m
SIDL from Viaduct 91.8 Tonnes
SIDL from Station 0 Tonnes
Total SIDL 91.8 Tonnes 918 kN
Pier no C30 Grid 15 Span 40m
SIDL Loading 9 Tonne/m
SIDL from Viaduct 180 Tonnes
SIDL from Station 0 Tonnes
Total SIDL 180 Tonnes
1800 kN

TWJO-1-TCD-ST1-0004-Rev A Page 9/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

c) SIDL from Roof Portal


Span Length = 12.5 m
Measured from
Width = 27.4 m Architecture drawings
Total Load = 128.4375 kN At intermediate support

Span Length = 12.91 m


Measured from
Width = 27.4 m Architecture drawings
Total Load = 132.6503 kN At end support

2.3.3 Live Load


The live load from the various components can be further described as:
d) Calculation of Live load (Viaduct in Station Area)

Maximum load/Rail = 140X4/(2X9.6) = 29.1 KN


CDI = 1.2
Applied UDL on each Rail = 34.92 KN/m.

e) Load from Either Span of Viaduct (At Station/Viaduct Interface)


Pier no C16 Grid 1 Span 20.4
LL from Viaduct 441.809 Tonnes
LL from Station 0 Tonnes
Impact 1.2
Total LL 530.1708 Tonnes
5301.708 kN
Pier no C30 Grid 15 Span 40
LL from Viaduct 717.367 Tonnes
LL from Station 0 Tonnes
Impact 1.2
Total LL 860.8404 Tonnes
8608.404 kN

TWJO-1-TCD-ST1-0004-Rev A Page 10/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

f) Load from Roof Portal


For LL at Portal, load of 1 kN/m2 is given in Design Manual
Span Length = 12.5 m
Width Measured from Architecture drawings = 27.4 m
Total Load At intermediate support = 171.25 kN

Span Length = 12.91 m


Width Measured from Architecture drawings = 27.4 m
Total Load At intermediate support = 176.867 kN

2.3.4 Braking & Traction Load


g) Braking and Traction within Station Area
For 25m span,
Number of Axle = 6 No’s
Total Load = 6 X140
= 840 KN
Braking/ Traction = 30% X840/25
= 10.08 KN
UDL/m / Rail = 10.08/2
= 5.04kN

h) Braking and Traction from Either Span of Viaduct (At Station/Viaduct


Interface)
Braking & Traction Load due to train live load (Non station End at Grid 1 )
For 20.4m Span
Total Axle Load 56 Tonnes 560 kN
Braking & Traction force to be applied at C16
i.e. 30% of total axle load 168 kN
Braking & Traction Load due to train live load (Non station End at Grid 15)
For 40m Span
Total Axle Load 112 Tonnes 1120 kN
Braking & Traction force to be applied at C30
i.e. 30% of total axle load 336 kN

TWJO-1-TCD-ST1-0004-Rev A Page 11/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

2.3.5 Temperature Load

Temperature and shrinkage effects


The temperature and shrinkage analysis has been done as per book "Design Aids for Limit State Design of
The seasonal variation in temperature , though more than its daily variation, is not important for structural
Maximum daily temperature t1 = 40 o C Design manual 5.1.4.2
Minimum daily temperature t2 = 15 o C Design manual 5.1.4.2
As the mean temperature of concreting of floors of a building is not likely to be the maximum or the minimum
Temperature differential for design of building = + 2/3 . (t1 - t2 ) = + 16.67 o C

The total shrinkage strain of concrete = 0.0003 Cl 4.2.6 C.Reynolds Handbook


Coefficient of thermal expansion of concrete = 1.20E-05 per o C BS 5400-2 Cl 5.4.6
Equivalent temperature for shrinkage = -25.00 o C
Since total shrinkage strain takes an infinite time to complete and that after about a year from the date of
= -12.50 o C
Thus, the temperature differential 't' of members is given by
t= 16.67 - 12.50 = 4.17 o C for temp. rise & shrinkage
t= -16.67 - -12.50 = 29.17 o C for temp. fall & shrinkage
For structural design of members, the calculated moments for temperature and shrinkage loading are to be
i) Shrinkage effect is reduced by 50% due to creep in a period of 30 days and gets reduced further as more
ii) Temperaure effect is partially reduced by creep, as it occurs gradually over a period of half a day.
iii) As the peak temperatures last only for a short duration and are, therefore, only skin deep, the average
iv) The elastic rebound of the columns reduces the floor displacement causing reduction in temperature and
v) The temperature and shrinkage moments are reduced by any loss of fixity at the base of columns due to
Hence the structure should be designed for a differential temperature of
t= 4.17 x 0.5 = 2.08 o C for temp. rise & shrinkage
With full
t= -29.17 x 0.5 = -14.58 o C for temp. fall & shrinkage value of E

Futher as per ACI the cracked inertia of RCC members may be taken as 70% of the gross inertia.
Therefore effective differential temperature for which the structure should be designed becomes
t= 2.08 x 0.7 = 1.46 o C for temp. rise & shrinkage With full
t= -14.58 x 0.7 = -10.21 o C for temp. fall & shrinkage value of E

2.3.6 Wind effects

Wind Load Calculation for all three Stations


Design Wind Pressure, Fd = 0.8 kN/m2
External Pressure Internal Span c/c Wind Load
Co-efficient, Cpe Pressure Co- of column to be
efficient, Cpi (m) applied
Ѳ (kN/m)

X Z X Z
0° 0.86 11 7.568
90° -1.3 11 -11.44
0° 0.59 12.5 5.9
90° -1.3 12.5 -13
0° 0.85 11 7.48
90° -0.6 11 -5.28
0° 0.68 12.5 6.8
90° -0.4 12.5 -4
Note : Pressure Coefficient are taken from BS 6399-2:1997 (Table 26 & Table 37)

TWJO-1-TCD-ST1-0004-Rev A Page 12/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

2.3.7 Seismic Loadings

Site Specific Seismic Design Spectra


Clause 15.1.3 of ODS stipulates the contractor shall derive the seismic wave
required for analysis and design of structures. Accordingly, seismic hazard
assessment was carried out by PT. LAPI ITB and submitted to the Engineer for
review. The report “Seismic hazard assessment for MRT project of DKI Jakarta”
dated 14 Feb. 2014 provides the details for derivation of seismic hazard
characteristics of the site. This report serves as the basis for derivation of ground
motions used in the design of viaduct and station structures contained in CP101 and
CP102.
The site specific response spectra for the project area were calculated using 18
earthquake time histories of ODE and other 18 earthquake time histories of MDE
from the above report. Section 5 describes the calculation of the site specific seismic
design spectra from the ground motion used in the seismic analysis.
Seismic Performance Criteria
In accordance with the “Supplemental Design Specification to ODS 15: Seismic
Loading” issued by the Engineer, the following criteria shall be met in verification of
structural response values:
i) Seismic Performance I (Service Limit Performance) shall be applied to
ODE earthquake
j) Seismic Performance II (Ultimate Limit Performance) shall be applied to
MDE earthquake.
The definition of seismic performance criteria are related to damage control as
below:-

k) Seismic Performance I
Function of structure is retained without conducting repair after an earthquake, and
no excessive displacement occurs.
l) Seismic Performance II
Repair may be required after an earthquake, but function of structure can be
restored within a short period.

The damage levels of reinforced concrete structures are defined in regards to the
load-displacement curve of the structure. The load-displacement relationship of
reinforced concrete columns subjected to moderate axial force for which the failure
mode is expected to be in flexure is similar to the curve shown in Figure 11.

Figure 11 - Envelop Curve of Load-Displacement Relation of Reinforced Concrete Members


(under low axial force)

TWJO-1-TCD-ST1-0004-Rev A Page 13/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Damage Level 1

Longitudinal reinforcement yield point is set as the limit for damage level 1. This is
shown by point B on the graph. It is expected that within this limit no extensive
repair will be necessary for the structure as the structure will remain essentially
elastic. Durability of structure however should be ensured as the structure has
suffered cracking.
Damage Level 2

The maximum capacity point (point C on graph) is set as the limit for damage level
2. At this point the longitudinal reinforcement has passed the yield point and the
cracks are wider. Crack injection and/or patching may be necessary.
Damage Level 3

The limit is set at the maximum displacement with no reduction in yield capacity
(point D). At this point it is expected that further displacement will occur without any
increase in capacity. The repair method is expected to include patching of spalled
concrete and remediation of ties.

The site specific spectrum defined as ODE is hence used as a serviceability


earthquake design wherein it is ensured that the structure remains in its elastic limit
and hence no Response Reduction Factor has been proposed with this condition

The site specific spectrum defined as ODE is hence used as a serviceability


earthquake design wherein it is ensured that the structure remains in its within the
elastic limit and hence no Response Reduction Factor has been proposed with this
condition.

For MDE, in accordance with EC8, the following response reduction factor is used:-

For I = 1, R = 1.68,
For I = 1.4, R = 2.35.
In line of the details specified above a graphical representation of spectrums is
compared and shown below. The graph compares the ODE, MDE spectrums with
the reduced spectrum for nominal earthquake as per SNI1726: 2012 with different
Response reduction factor as per SNI1726.

TWJO-1-TCD-ST1-0004-Rev A Page 14/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

0.70
SNI 1726 Design Spectrum
0.60
ODE - Soil Profile - A
0.50
Spectral Acceleration

SNI 1726 / (RRF = 8 / Ie =


1.25)
0.40
SNI 1726 / (RRF = 5 /Ie =
1.25)
0.30

0.20

0.10

0.00
0.00 1.00 2.00 3.00 4.00 5.00 6.00
Time Period

Figure 12 – Comparison of ODE Design Spectrum


Hence based on the above comparison it can be clearly concluded that after
application of reduction factor, importance factor the design curve for spectrum is
lower than ODE when compared with SNI 1726:2012 if RRF is used as 5 or 8. Since
the structure is frame structure in both directions it cannot possess RRF less than 5
based on SNI1726 guidelines. Further since our design is entirely based on ODE
spectrum without any RRF it is deemed to have a higher structural strength than the
strength that would have been evaluated using the SNI1726 code for its general
service conditions.

1
SNI 1726 Design Spectrum * 1.5
0.9
MDE - Soil Profile A
0.8
SNI 1726 * 1.5 / (RRF = 8/Ie = 1.25)
Spectral Acceleration (g)

0.7
SNI 1726*1.5 / (RRF = 5 /Ie = 1.25)
0.6
MDE / (RRF 2.37/ I = 1.4)
0.5

0.4

0.3

0.2

0.1

0
0.00 1.00 2.00 3.00 4.00 5.00 6.00
Time Period

Figure 13 – Comparison of MDE Spectrum

TWJO-1-TCD-ST1-0004-Rev A Page 15/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Further it can also be seen that as defined earlier the Reduction factor of 2.35 with
Importance factor of 1.4 resulting in net reduction of MDE spectrum by 1.68 can be
further used to decrease the MDE design spectrum to provide for an economic
design. Please note that even after this reduction this MDE spectrum still is higher
that the Ultimate earthquake spectrum with reduction factors of either 5 or 8.

In conclusion, for the seismic loading conditions, using the ODE and MDE response
spectrum and criterion as directed by the “Supplemental Design Specification to
ODS 15: Seismic Loading” issued by the Engineer is more onerous than the
response spectrum from SNI1726:2012 as can be seen from Figure 13 and Figure
14.

2.4 Load Combinations


The static load combinations and load factors for SNI and British Standards
(BS8110) and EC8 for Seismic are summarised in the Table below:-
Table 2 – Summary of Load Combinations
SNI BS8110/EC2
1 Normal - Service 1.0D + 1.0L 1.0D + 1.0L
2 Normal - Ultimate 1.2D + 1.6L 1.4D + 1.6L
3 Seismic - ODE 1.0D + 0.75L + 0.525E 1.0D + 1.0L + 1.0E
4 Seismic - MDE 1.2D + 1.0L + 1.0E 1.0D + 1.0L + 1.0E

From the table, under normal conditions the serviceability and ultimate limit state for
the load combination using the British code is more onerous. For the seismic
condition, ODE conditions, EC8 is more onerous. However, for MDE, based on load
combination factor, SNI is more onerous, but due to the higher response factor (E),
the design in accordance with EC8 is more onerous.

TWJO-1-TCD-ST1-0004-Rev A Page 16/55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

3. STRUCTURAL ANALYSIS
3.1 Seismic Response of structure
Response Spectrum Analysis is adopted to analyze the behavior of the entire
structure during a seismic event. This approach permits the multiple modes of
response of a structure to be taken into account. This is required in many building
codes for all except for very simple or very complex structures. The response of a
structure can be defined as a combination of many mode shapes. In this analysis,
STAAD Pro software is used to determine these modes for a structure. For each
mode, a response is read from the design spectrum, two design spectrums i.e. ODE
and MDE. It is based on the modal frequency and the modal mass, and they are
further combined to provide an estimate of the total response of the structure.
Combination methods include the complete quadratic combination (CQC).

3.2 Mode Shapes


Mode shapes from the analysis are shown below and the behaviour of the structure
is quite balanced in both X and Z directions as it can be figure out from the output
results of STAAD analysis. In Mode 1, mass in Z direction is 96.13 and in Mode 3,
mass in X direction is 96.37 which is just a marginal difference. It concludes that the
structure is well behaved in translational and the chance of torsion is minimal.
Table 3 – STAAD mass participation table

Figure 14 – Mode Shape 1 – Transverse Translation

TWJO-1-TCD-ST1- 0004-Rev A PAGE 17 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 15 – Mode Shape 2 – Ineffective participation

Figure 16 -Mode Shape 3 – Longitudinal Translation

TWJO-1-TCD-ST1- 0004-Rev A PAGE 18 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

3.3 Fundamental Time period


The fundamental time period of Mode 1 obtained in analysis is 1.39604 sec, as it
can be seen from the analysis output results. But the time period obtained from the
empirical formula which is given Clause 7.8.2.1 SNI 1726-2012 comes around 0.49
sec (Moment bearing load frame Table 15) and the height of structure is 13.8m. It
cannot be exactly matched with given in SNI 1726-2012 because the analysis has
been done with the pile model and it takes the actual height from the point of fixity of
pile. The actual time period used in the analysis has been calculated by default.

3.4 Seismic mass participation


From the analysis of this structure using STAAD Pro, the mass participation of this
entire structure comes around 97.624 and 97.783 percent at mode 3 in both X and Z
directions respectively. Since the mass participation is more than 90 percent and it
clearly shows that the analysis obtained mass participation of the actual mass of the
structure as per the Clause 7.9.1 of SNI1726 – 2012.

3.5 Lateral Seismic Inter-storey drift


Assuming Seismic Risk Category as Category IV while evaluating the seismic storey
drifts at different floor levels following parameters have been used from SNI
1726:2012.
Importance Factor =1.50 (Refer Table 2 of SNI 1726:2012)
Deflection Magnificaton Factor =5.50 (Refer Table 9 for SMRF – RC – C.5)
But please note that this amplification factor is based on a reduction factor in
spectrum. The reduction factor = 8.0 (Refer Table 9 for SMRF – RC – C.5)

With the site specific spectrum since we are following a reduction factor of 2.37 with
Importance factor 1.4 we should alter this amplification factor in proportionality to
make it on the same grounds for SNI1726:2012.

Mass center deflection on level x (δx) (mm) must be determined in accordance with
following equation:
𝐶𝑑 𝛿𝑥𝑒
𝛿𝑥 =
𝐼𝑒

Annotation:
Cd = deflection amplification factor in Table 9
δxe = deflection on required location in this article that determined by elastic
analysis
Ie = earthquake significance factor that determined in accordance with 4.1.2 of
SNI 1726:2012.
SNI 1726:2012 Design value
Design Spectrum (Sa/g) (Sa/g)SNI 1726:2012 (Sa/g)SOIL PROFILE A - MDE
Load Combination Factor 1.5 1.0
Importance Factor 1.5 1.4
Response Reduction 8.0 2.35
Factor
Deflection Amplification 5.5 To be evaluated (X)
factor

TWJO-1-TCD-ST1- 0004-Rev A PAGE 19 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Hence for both the parameters to be on same grounds the following


relationship can be established:
(Sa/g)SNI 1726:2012 * FOS * Ie * Cd / RRF = (Sa/g)SOIL PROFILE A - MDE* FOS * Ie * (X) / RRF

For,
Time period (T) = 1.39604 seconds
(Sa/g)SNI 1726:2012 = 0.765 (including FOS = 1.5)
(Sa/g)SOIL PROFILE A – MDE = 0.33408

Hence
X = (0.765 * 1.5 * 5.5 / 8.0)/ (.33408*1.4/2.35) = 4.373 say 4.40

Allowable deviation between the floors is = 0.015hsx.

Following table gives the nodal displacements at different level including ground,
their amplified values and relative displacement between the floors compared to the
limits.
Table 4 – Drift Displacements from STAAD and amplified values in longitudinal
direction

Concourse level Platform level

Magnified Magnified
Nodal Drift Displacement Nodal Drift Displacement
from STAAD at lower from STAAD, at upper
δe2 concourse δe3 concourse
level, δ2 level, δ3

mm mm mm mm
51.988 152.50 72.981 214.08
52.587 154.26 73.361 215.19
50.194 147.24 73.183 214.67
52.628 154.38 73.087 214.39
49.907 146.39 73.166 214.62
52.669 154.50 73.019 214.19
49.991 146.64 73.144 214.56
52.764 154.77 73.121 214.49
49.853 146.24 73.378 215.24
53.356 156.51 73.406 215.32
50.200 147.25 73.632 215.99
53.483 156.88 73.526 215.68
50.178 147.19 73.627 215.97
53.189 156.02 73.466 215.50
50.201 147.26 73.605 215.91
53.137 155.87 73.491 215.57
50.302 147.55 73.598 215.89

TWJO-1-TCD-ST1- 0004-Rev A PAGE 20 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

44.073 129.28 75.596 221.75


46.327 135.89 73.441 215.43
46.891 137.55 75.573 221.68
45.986 134.89 75.524 221.54
46.571 136.61 75.403 221.18
46.084 135.18 75.176 220.52
43.726 128.26 74.781 219.36
49.314 144.65 74.513 218.57
47.208 138.48 74.429 218.33
47.013 137.90 74.185 217.61
49.345 144.75 73.835 216.58
48.688 142.82 73.547 215.74
49.713 145.82 73.110 214.46
48.585 142.52 73.069 214.34
48.950 143.59 73.190 214.69
47.175 138.38 73.357 215.18
45.679 133.99 73.423 215.37
49.892 146.35 71.179 208.79
48.860 143.32 74.185 217.61
49.530 145.29 71.169 208.76
48.579 142.50 71.175 208.78
49.603 145.50 71.194 208.84
48.077 141.03 71.207 208.87
49.167 144.22 71.185 208.81
47.695 139.91 71.591 210.00
49.297 144.60 72.710 213.28
47.003 137.88 73.354 215.17
50.423 147.91 73.944 216.90
47.428 139.12 74.364 218.13
48.300 141.68 74.223 217.72
47.352 138.90 74.116 217.41
48.351 141.83 74.153 217.52
46.865 137.47 74.120 217.42
48.699 142.85 74.096 217.35

Table 5 – comparison of displacements with inter-storey drift limits

Ground to concourse Concourse to platform


Deviation Deviation Result Deviation Deviation Result
value limit value limit
mm mm mm mm
0.015 * 0.015 *
8000 5700
51.988 120 OK 61.579 85.5 OK
52.587 120 OK 60.937 85.5 OK

TWJO-1-TCD-ST1- 0004-Rev A PAGE 21 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

50.194 120 OK 67.434 85.5 OK


52.628 120 OK 60.013 85.5 OK
49.907 120 OK 68.226 85.5 OK
52.669 120 OK 59.693 85.5 OK
49.991 120 OK 67.915 85.5 OK
52.764 120 OK 59.714 85.5 OK
49.853 120 OK 69.007 85.5 OK
53.356 120 OK 58.813 85.5 OK
50.200 120 OK 68.734 85.5 OK
53.483 120 OK 58.793 85.5 OK
50.178 120 OK 68.784 85.5 OK
53.189 120 OK 59.479 85.5 OK
50.201 120 OK 68.652 85.5 OK
53.137 120 OK 59.705 85.5 OK
50.302 120 OK 68.335 85.5 OK
44.073 120 OK 83.467 85.5 OK
46.327 120 OK 79.534 85.5 OK
46.891 120 OK 84.134 85.5 OK
45.986 120 OK 82.645 85.5 OK
46.571 120 OK 84.574 85.5 OK
46.084 120 OK 85.337 85.5 OK
43.726 120 OK 81.095 85.5 OK
49.314 120 OK 73.917 85.5 OK
47.208 120 OK 79.848 85.5 OK
47.013 120 OK 79.705 85.5 OK
49.345 120 OK 71.837 85.5 OK
48.688 120 OK 72.920 85.5 OK
49.713 120 OK 68.631 85.5 OK
48.585 120 OK 71.820 85.5 OK
48.950 120 OK 71.104 85.5 OK
47.175 120 OK 76.801 85.5 OK
45.679 120 OK 81.382 85.5 OK
49.892 120 OK 62.442 85.5 OK
48.860 120 OK 74.287 85.5 OK
49.530 120 OK 63.474 85.5 OK
48.579 120 OK 66.282 85.5 OK
49.603 120 OK 63.334 85.5 OK
48.077 120 OK 67.848 85.5 OK
49.167 120 OK 64.586 85.5 OK
47.695 120 OK 70.095 85.5 OK
49.297 120 OK 68.678 85.5 OK
47.003 120 OK 77.296 85.5 OK
50.423 120 OK 68.995 85.5 OK
47.428 120 OK 79.012 85.5 OK

TWJO-1-TCD-ST1- 0004-Rev A PAGE 22 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

48.300 120 OK 76.041 85.5 OK


47.352 120 OK 78.508 85.5 OK
48.351 120 OK 75.686 85.5 OK
46.865 120 OK 79.948 85.5 OK
48.699 120 OK 74.498 85.5 OK
Table 6 – Drift Displacements from STAAD and amplified values in Transverse
direction

Concourse Level Platform Level

Magnified Magnified
Nodal Drift Displacement Nodal Drift Displacement
from STAAD at lower from STAAD, at upper
δe2 concourse δe3 concourse
level, δ2 level, δ3

mm mm mm mm
67.493 112.49 93.379 155.63
66.652 111.09 91.917 153.20
61.662 102.77 93.408 155.68
67.069 111.78 93.024 155.04
61.248 102.08 92.808 154.68
66.510 110.85 92.115 153.53
60.290 100.48 91.701 152.84
65.962 109.94 91.220 152.03
59.851 99.75 91.436 152.39
66.475 110.79 91.435 152.39
60.546 100.91 91.807 153.01
67.087 111.81 91.720 152.87
60.311 100.52 91.576 152.63
65.838 109.73 91.207 152.01
59.867 99.78 91.489 152.48
66.129 110.22 91.669 152.78
60.774 101.29 92.050 153.42
61.335 102.23 93.442 155.74
60.412 100.69 91.978 153.30
58.952 98.25 93.414 155.69
60.801 101.34 93.088 155.15
58.569 97.62 92.821 154.70
60.240 100.40 92.185 153.64
58.004 96.67 91.640 152.73
59.464 99.11 91.227 152.05
58.192 96.99 91.431 152.39
59.904 99.84 91.536 152.56
57.547 95.91 91.786 152.98

TWJO-1-TCD-ST1- 0004-Rev A PAGE 23 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

59.423 99.04 91.798 153.00


58.636 97.73 91.571 152.62
59.616 99.36 91.317 152.20
58.209 97.02 91.453 152.42
61.335 102.23 91.738 152.90
60.372 100.62 92.059 153.43
58.953 98.26 93.436 155.73
60.813 101.36 92.008 153.35
58.573 97.62 93.407 155.68
60.426 100.71 93.081 155.14
60.618 101.03 92.817 154.70
62.784 104.64 92.183 153.64
60.587 100.98 91.736 152.89
61.773 102.96 91.265 152.11
60.167 100.28 91.466 152.44
60.315 100.53 91.542 152.57
60.508 100.85 91.823 153.04
61.647 102.75 91.816 153.03
60.427 100.71 91.607 152.68
60.127 100.21 91.728 152.88
58.114 96.86 92.067 153.45
56.788 94.65 91.184 151.97
55.484 92.47 91.497 152.50

Table 7 – comparison of displacements with inter-storey drift limits

Ground To Concourse Concourse to platform


Deviation Deviation Result Deviation Deviation Result
value limit value limit
mm mm mm mm
0.015 * 0.015 *
8000 5700
67.493 120 OK 43.143 85.5 OK
66.652 120 OK 42.108 85.5 OK
61.662 120 OK 52.910 85.5 OK
67.069 120 OK 43.258 85.5 OK
61.248 120 OK 52.600 85.5 OK
66.510 120 OK 42.675 85.5 OK
60.290 120 OK 52.352 85.5 OK
65.962 120 OK 42.097 85.5 OK
59.851 120 OK 52.642 85.5 OK
66.475 120 OK 41.600 85.5 OK
60.546 120 OK 52.102 85.5 OK
67.087 120 OK 41.055 85.5 OK
60.311 120 OK 52.108 85.5 OK

TWJO-1-TCD-ST1- 0004-Rev A PAGE 24 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

65.838 120 OK 42.282 85.5 OK


59.867 120 OK 52.703 85.5 OK
66.129 120 OK 42.567 85.5 OK
60.774 120 OK 52.127 85.5 OK
61.335 120 OK 53.512 85.5 OK
60.412 120 OK 52.610 85.5 OK
58.952 120 OK 57.437 85.5 OK
60.801 120 OK 53.812 85.5 OK
58.569 120 OK 57.087 85.5 OK
60.240 120 OK 53.242 85.5 OK
58.004 120 OK 56.060 85.5 OK
59.464 120 OK 52.938 85.5 OK
58.192 120 OK 55.398 85.5 OK
59.904 120 OK 52.720 85.5 OK
57.547 120 OK 57.065 85.5 OK
59.423 120 OK 53.958 85.5 OK
58.636 120 OK 54.892 85.5 OK
59.616 120 OK 52.835 85.5 OK
58.209 120 OK 55.407 85.5 OK
61.335 120 OK 50.672 85.5 OK
60.372 120 OK 52.812 85.5 OK
58.953 120 OK 57.472 85.5 OK
60.813 120 OK 51.992 85.5 OK
58.573 120 OK 58.057 85.5 OK
60.426 120 OK 54.425 85.5 OK
60.618 120 OK 53.665 85.5 OK
62.784 120 OK 48.998 85.5 OK
60.587 120 OK 51.915 85.5 OK
61.773 120 OK 49.153 85.5 OK
60.167 120 OK 52.165 85.5 OK
60.315 120 OK 52.045 85.5 OK
60.508 120 OK 52.192 85.5 OK
61.647 120 OK 50.282 85.5 OK
60.427 120 OK 51.967 85.5 OK
60.127 120 OK 52.668 85.5 OK
58.114 120 OK 56.588 85.5 OK
56.788 120 OK 57.327 85.5 OK
55.484 120 OK 60.022 85.5 OK

TWJO-1-TCD-ST1- 0004-Rev A PAGE 25 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

4. SUBSOIL CONDITIONS

4.1 Stratification
The subsoil encountered at the Cipete Raya Station site generally consists of the
Alluvial Fan (Unit Qav) and the Bojongmanik Formation (Unit Tmb) as shown below.
The stratification of the project site can be found in Appendix A.
Detailed information of geotechnical condition at the project site is described in
Geotechnical Interpretative Report ((TWJO-CP12-TCD-DSR-0001-Rev 2)).

4.1.1 Stratum 1: Alluvial Fan (Unit Qav)


The Alluvial Fan (Unit Qav) mainly consists of recent deposits of volcanic ash (tuff)
consisting of high plasticity clayey silts. The Alluvial Fan can be further subdivided
into three layers, in the order of increasing consistency as follows:
m) Layer 1: AC1
The thickness of this layer ranges from 4m to 19m. It is of very soft to medium
consistency with SPT N values generally of 5 and below. The colour of AC1
material is generally red to reddish brown.
n) Layer 2: AC2
The colour of the AC2 material is generally reddish brown, greyish brown and
yellowish brown. The consistency of the soil varies from medium to very stiff
with the SPT-N blow counts generally in the range of 6 to 20. The AC2 layer is
generally encountered beneath AC1 with thickness ranging from 1m to 24m.
o) Layer 2: AC3
The AC3 layer lies beneath the AC2 layer, with thickness between 1 to 12m.
The AC3 material is generally brown, greyish brown and yellowish brown. The
consistency of the AC3 layer varies from very stiff to hard with the SPT-N blow
counts in the range of 15 to 50.

4.1.2 Stratum 2: Bojongmanik Formation (Unit Tmb)


This stratum underlies the Alluvial Fan (Unit Qav) and mainly consists of weathered
claystone alternating with weathered sandstone. No bedrock was encountered at
the borehole locations at the project site. The stratum is typically black and dark
grey, and becomes brown to brownish yellow to the top of the stratum. The deposits
can be further divided into two sublayers as follows:
a) Layer 1: TC (clay layer)
The TC layer consists of high plasticity clayey silts. Generally, TC layer has a
very stiff to very hard consistency, where the majority of the SPT-N values are
50 and above.
b) Layer 2: TS (sand layer)
TS layer generally consists of cemented sands, silty sands and silty gravels.
The sands are generally dense to very dense with the majority of SPT-N
values being 50 and above.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 26 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

4.2 Groundwater Conditions


Groundwater was measured in all boreholes during the SI works. Based on the
groundwater levels measured during borehole drilling, the groundwater levels
generally range from 1.0m to 9.6m below ground level (mbgl) with an average of
4.7mbgl.
Casagrande type standpipes were installed in boreholes within CP104 and CP105
to monitor the existing ground water table for approximately 6 months. Based on the
groundwater monitoring results of these standpipes, the groundwater levels
generally range from 2.3mbgl to 8.1mbgl with an average of 5.1mbgl. The readings
were relatively stable throughout the six months of monitoring period. However,
discrepancies would be expected as this monitoring are located few kms away from
the CP101 and CP102 site.

4.2.1 Borehole Reference


There are four boreholes in the vicinity of Lebak Bulus Station, namely: 1ABH-4, E-
120, 1ABH-5, E-130. For the design, 1ABH-4 will be adopted to compute the pile
axial capacity conservatively. The soil stratification is presented in Figure 17.

4.3 Reduction of Soil Properties due to Cyclic Loading


4.3.1 Reduction of Undrained Shear Strength
Undrained shear strength (Su) based methodology was used to assess the potential
for cyclic softening (Boulanger and Idriss 2007). Based on this assessment, about
half of the AC1 and AC2 layers will undergo cyclic softening under the ODE
earthquake and almost the entire layers under the MDE earthquake. Thus, it could
be assumed that all of the AC1 and AC2 layers will undergo cyclic softening during
the design earthquake.
Reduction in undrained strength was calculated according to the Designers’ Guide
to EN 1998 Section 10.3.1.1 (Fardis et al. 2005). Based on these analysis, it is
recommended that 20% reduction in the undrained shear strength should be applied
to the soft and medium cohesive soils (AC1 and AC2) under earthquake loading.
Detailed calculation of cyclic softening assessment and undrained shear strength
reduction due to earthquake loading at the project site is described in Geotechnical
Interpretative Report (TWJO-CP12-TCD-DSR-0001-Rev 2)

4.3.2 Reduction of Soil Stiffness


The effective reduction in the soil stiffness due to cyclic loading under earthquake
conditions shall be taken into account by using stiffness parameters equal to 70% of
their static values. The suggestion is based on the recommendations of ACI
Committee 336.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 27 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Figure 17 - Soil stratification

Figure 18 - Layout of Site Zoning

TWJO-1-TCD-ST1- 0004-Rev A PAGE 28 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak bulus Station Foundation Design

4.4 Subsoil Properties


The subsoil properties for geotechnical design from the Geotechnical Interpretative Report are reproduced in Table 8 below.

Table 8 - Recommended Geotechnical Design Parameters

ALLUVIAL FAN BOJONGMANIK FORMATION


Soil Parameter Symbol Unit
AC1 AC2 AC3 TC TS
SPT-N  0-5 6-20 20-50 20-50 20-50
Bulk Density w kN/m3 15.5 (14 – 17) 15.5 (14 – 17) 15.5 (14 – 17) 16 (14 – 17.5) 18 (16 – 20)
2 a a
Undrained Shear Strength cu kN/m 5N 4.5N 4.5N 4.5N -
2 f f
Effective Cohesion c' kN/m 4 4 6 10 0
Effective Angle of Friction ' o
22 22 25 b
28 b
35c
Void ratio e0 2.0 (1.2 – 2.5) 2.0 (1.2 – 2.5) 2.0 (1.2 – 2.5) 1.8 (1.2 – 2.2) 1.0 (0.5 – 1.2)
Compression Index Cc 0.45 (0.3 – 0.7) 0.45 (0.3 – 0.7) 0.2 – 1.0d 0.2 – 1.0d -
Recompression Index Cr 0.045 (0.03 – 0.07) 0.045 (0.03 – 0.07) 0.05 – 0.25d 0.05 – 0.25d -
Preconsolidation
P’c kN/m2 80 (50 – 150) 80 (50 – 150) 460-1350 460-1350 -
Pressure
Coefficient of
Cv m2/yr 11 (5 – 25) 11 (5 – 25) 9.5d 9.5d -
Consolidation
Eu MPa 1.5N 1.5N 2N 2N -
Elastic Modulus
E' MPa Eu/1.15 2N
Permeability k m/s 1×10-7 1×10-7 1×10-7 1×10-7 1×10-6e

a d
Based on Stroud (1989) Based on Toha and Sengara (2009)
b e
Based on Bjerrum and Simons (1960) Based on Casagrande (1938)
c f
Based on Peck et al. (1974) Based on common correlation of c’ = 0.2 N (using average SPT-N of 30 for AC3 and 50 for TC)

TWJO-1-TCD-ST1- 0004-Rev A PAGE 29 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

5. SITE SPECIFIC RESPONSE ANALYSIS

5.1 Earthquake Ground Motion at Bedrock


This SSRA are based on total of 36 earthquake time histories at bedrock (18 for
ODE and 18 for MDE) produced by PT LAPI ITB. These time histories are part of
the input of EERA program. Detail information regarding this earthquake time
histories is delivered by PT LAPI ITB in “Seismic Hazard Assessment for MRT
Project of DKI Jakarta”, dated February 2014.
According to the SDS Clause 3.2.2, bedrock is located 350m beneath the existing
ground surface.

5.2 Correlation of Shear Wave Velocity (Vs) to SPT-N Value


Correlation of Imai Tonouchi (1982) was selected for the SSRA. This correlation
also matches the local correlation for Jakarta soils quite well (Fauzi et al., 2014).

Table 9 - List of published studies on Vs to SPT-N correlations

Published Studies Source Published correlation


Local Jakarta soils Fauzi et al. 2014 105.03N0.286
Imai and Tonouchi 1982 96.9N0.314
International
Sun et al. 2008 75.76N0.371

5.3 Site Zoning


Based on the sensitivity analysis, it can be concluded that there are two main
variable of subsoil condition which controlling the SSRA result, for instance:
1. The SPT-N of the top layer (of around 0-10mbgl): where the amplification effect
increases with decreasing SPT-N, and
2. The thicknesses of the low SPT-N layer: where amplification effect reaches a
maximum at a certain critical depth of 10-12m for the MDE earthquake and 12-
15m.
Thus, the project site was classified into SSRA zone based on its soft soil layer
thicknesses (Table 10). Moderately conservative SPT-N values of the top 10m soil
layer were selected for this analysis. The Vs profiles can be seen in Figure 19. The
plan view showing the zoning of the project site is presented in Figure 20.

Table 10 - Site Zoning

Zone Thickness of Soft Soil Layer (Layer A)


A <10m
B 10-15m
C >15m

TWJO-1-TCD-ST1- 0004-Rev A PAGE 30 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Vs (m/s)
100 150 200 250 300 350
0

10
Depth below Ground Level (mbgl)

15

20

25

30

35

40
Group A (Layer A thickness <=10m)
Group B (Layer A thickness = 10-15m)
45
Group C (Layer A thickness > 15m)

50

Figure 19 - Design shear wave velocity profiles for each zone.

Figure 20 - Zoning for site specific response analysis

TWJO-1-TCD-ST1- 0004-Rev A PAGE 31 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

5.4 Site Specific Response Spectra Result


The site specific response spectra for each of the 3 zones were calculated using 18
earthquake time histories of ODE and other 18 earthquake time histories of MDE.
Afterwards, the overall design spectra was determined based on the envelope of the
average + standard deviation line of all the 18 site specific response spectra result.
This approach was applied for both the ODE and MDE cases. The site specific
response analyses for these 3 zones are plotted together (Figure 21 and Figure 22).
0.5
Design Spectra - Group A

0.5 Design Spectra - Group B


Design Spectra - Group C

0.4
Spectral Acceleration (g)

0.4

0.3

0.3 ODE (Return Period 100 years)

0.2

0.2

0.1

0.1

0.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0
Period (sec)
Figure 21 - Design Spectra for ODE case

1.0
Design Spectra - Group A
Design Spectra - Group B
0.9
Design Spectra - Group C

0.8
Spectral Acceleration (g)

0.7

0.6

0.5 MDE (Return Period 1000 years)

0.4

0.3

0.2

0.1

0.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0
Period (sec)
Figure 22 - Design Spectra for MDE case

TWJO-1-TCD-ST1- 0004-Rev A PAGE 32 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

6. PILE BEARING CAPACITY

6.1 Factor of Safety


Factor of safety for axial bearing capacity of pile foundation shall be based on BS
8004. For the design under seismic conditions, the factor of safety also complies
with Jakarta’s regulation of Structural and Geotechnical Design Guidelines for
Buildings (Dinas Penataan dan Pengawasan Bangunan DKI Jakarta, 2007).
The minimum factor of safety for pile design from the Civil and Structure Design
Manual (TWJO-CP1-TCD-DSM-0001-Rev 2) are reproduced Table 11.

Table 11 - Minimum Factor of Safety for Design

Minimum Factor of Safety


Loading Condition
Compression Tension
(Qs + Qb) / 2.5
Static Loading Qs / 3.0
Qs / 2.0
Seismic Loading Level-1 (ODE) Qs / 1.5 Qs / 2.0
Seismic Loading Level-2 (MDE) (Qs + Qb) / 1.0 Qs / 1.5

6.2 Bearing Capacity Analysis


6.2.1 Axial Bearing Capacity
The allowable geotechnical bearing capacity for compression pile is given by the
following equation:
Qa = Qu / FS
where:
Qa : allowable bearing capacity;
Qu : ultimate bearing capacity;
FS : factor of safety.

The value of ultimate bearing capacity, Qu, unit frictional resistance, fs, and unit base
resistance, qb, can be determined by following.
c) Ultimate Bearing Capacity
The ultimate geotechnical bearing capacity for compression pile is given by the
following equation:
Qu = Qsp + Qb
= fs As + qb Ab
where:
Qsp : is the ultimate positive shaft resistance
Qb : is the ultimate end bearing resistance
fs : is the average skin friction or adhesion per unit area of the shaft at
the condition of full mobilization of frictional resistance;

TWJO-1-TCD-ST1- 0004-Rev A PAGE 33 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

qb : is the ultimate value of the resistance per unit area of base due to the
shearing strength of the soil;
As : is the surface of the pile shaft;
Ab : is the plan area of the base.

d) Unit frictional resistance


fs = Ks N
where:
N : N-SPT values along the pile shaft;
Ks : coefficient of unit frictional resistance, determined based on empirical
correlation and verified with preliminary pile test.

e) Unit base resistance


qb = Kb N
where:
N : N-SPT values at the pile base;
Kb : coefficient of unit base resistance, determined based on empirical
correlation and verified with preliminary pile test.
6.3 Design Parameters for Axial Bearing Capacity
The unit frictional resistance, fs, and unit base resistance, qb, being adopted in the
design from the Civil and Structure Design Manual (TWJO-CP1-TCD-DSM-0001-
Rev 2) are reproduced inTable 12. These design parameters shall be confirmed with
preliminary pile test result.

Table 12 - Bored Pile Design Parameters*

Unit frictional resistance, fs Unit base resistance, qb


Soil Type (kN/m2) (kN/m2)
Value Limit Value Limit
AC1 4.5 Na - - -
a a
AC2 4.5 N 200 45 N 4000
a a
AC3 4N 200 45 N 4000
TC 4 Na 200 45 Na 4000
TS 3 Nb 170b 60 Nb 4000b
* The design unit frictional resistance and unit base resistance of the pile foundation
to be duly verified by result of preliminary pile test
a
Based on reference to Rudianto & Soedjono (2009)
b
Based on reference to Reese & Wright (1997)

TWJO-1-TCD-ST1- 0004-Rev A PAGE 34 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

6.4 Pile Group


6.4.1 Spacing of Piles
According to BS 8004, general working rules of pile spacing are as follows:
 Friction piles: centre to centre spacing should be not less than the perimeter
of the pile or, for circular piles, centre to centre spacing should be not less
than three times the diameter.
 End-bearing piles: spacing may be reduced, but the distance between the
surfaces of the shafts of adjacent piles should be not less than the least
width of the piles.
Generally, group reduction factors need not be applied where:
 The centre-to-centre spacings are of more than 3 times the perimeter of the
piles or the circumscribed rectangles in the case of H-piles; or
 The load capacity of the piles is derived from end-bearing; or
 The piles are rock-socketed piles

6.4.2 Block Failure Analysis


There would be negligible risk of general shear failure of the group since the piles in
groups are designed to be embedded in hard soils (SPT-N > 50). However, block
failure check based on Tomlinson (1994) is carried out to confirm the safety of the
groups.
𝑄 = 2𝐷(𝐵 + 𝐿)𝑐 + 1.3𝑐𝑏 𝑠𝑁𝑐 𝐵𝐿
Where,
D : depth of the piles below ground level,
B : overall width of the group,
L : overall length of the group,
c : average cohesion of the clay over the pile embedment depth,
cb : cohesion of the clay at the pile base level or within the zone of soil below the
base affected by the loading,
s : shape factor, and
Nc : bearing capacity factor.

Figure 23 – Bearing capacity factor (after Meyerhof) and shape factor (Meyerhof-
Skempton

TWJO-1-TCD-ST1- 0004-Rev A PAGE 35 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Based on the analysis, the ultimate bearing capacity of the soil block is significantly
higher than the sum of working load on the pile groups.

6.5 Result of Analysis


Pile lengths are designed based on available working load. The summary of the
result will be presented in Appendix C. Detailed calculation of the pile axial bearing
capacity is presented in Appendix D. Table 13 summarizes the result of pile length
analysis and the working loads adopted.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 36 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

7. LATERAL DEFLECTION OF PILE

7.1 Allowable Lateral Displacements


Allowable lateral displacements for piles should be consistent with the function and
type of structure, the anticipated service life, and the consequences of
unacceptable displacements on the performance of the structure.

7.2 Pile Model and Soil-Structure-Interaction


The problem of the laterally loaded pile is a soil-structure-interaction problem since
the amount of pile bending must be consistent with the soil properties and the pier
stiffness. In the analysis, the pile deflection analysis is done integrated with the
structural model by modeling the piles with spring constant as soil resistance. Model
of a pile under lateral loading showing concept of bilinear soil response curve
(Reese and O’Neill, 1988) is shown in Figure 24.
The 2D p-y concept is based on the synthesis of full scale pile load tests and soil
properties. Shear at the base of the pile is neglected because the pile is considered
sufficiently long that lengths are assumed to extend below the theoretical depth of
fixity. Spring support stiffness as well as the pressure limitation to represent the soil
elastic-plastic behavior is described in the following section.

Figure 24 – Pile-Soil Model (after Reese and O’Neill, 1988)

7.3 Design Parameters for Lateral Soil Capacity and Stiffness


7.3.1 Lateral Capacity of Soils
The limiting pressure of soils (Pu) for laterally loaded pile is taken as 2Su×D at
ground surface (where Su is undrained shear strength and D is pile diameter), and
linearly increase until 9Su×D at depth of 3D (Broms, 1964; Fleming et al, 2009).

TWJO-1-TCD-ST1- 0004-Rev A PAGE 37 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Figure 25 – Idealized variation of limiting resistance with depth (after Fleming et al,
2009)

7.3.2 Horizontal Subgrade Modulus


The modulus of subgrade reaction (k’s) is a conceptual relationship between soil
pressure and deflection of foundation structures. The value of this modulus will be
determined based on its relationship to the soil stiffness parameter (E) using Vesic
equation (1961a, 1961b).

12 𝐸𝑠 𝐵 4 𝐸𝑠
𝑘 ′ 𝑠 = 0.65 √
𝐸𝑓 𝐼𝑓 1 − 𝜇2

where,
k’s : modulus of subgrade reaction, in units of Es,
Es and Ef : modulus of soil and foundation structures, respectively; inconsistent
units,
B and If : foundation width and its moment of inertia based on cross section;
inconsistent units,
 : Poisson ratio of soil.

Detailed of this equation is described in Geotechnical Interpretative Report (TWJO-


CP12-TCD-DSR-0001-Rev 2). This design horizontal subgrade modulus shall be
duly verified by result of preliminary pile test.

7.4 Pile Group


7.4.1 Spacing of Piles
General working rules of pile spacing are described in Section 5.4.1.
7.4.2 Group Effect
To capture the effect of pile group under lateral loadings, the load deformation
response of pile groups under general loading conditions will be further verified.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 38 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

8. Design of Foundation

8.1 Bored Pile Design


Pile lengths are designed based on the result of the working load obtained from the
pile-structure interaction model. Table 13 - Summary of Design Pile Length
summarizes the result of pile length design for the working loads.
A detailed summary of the result are presented in Appendix C and detailed
calculation of the pile axial bearing capacity is presented in Appendix D.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 39 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Table 13 - Summary of Design Pile Length

No. of Pile Vertical Load per Pile (kN)


Load Column No(s). / Pile
Piles / Diameter Static ODE MDE
Category Pile Group Length (m)
Column (m) Compression Tension Compression Tension Compression Tension
A PG1A 1 1.0 692 - 802 - 1150 - 11
B C53 1 1.0 1121 - 3217 1270 3948 1694 21.5
C C57 1 1.0 2132 - 4054 718 6757 2271 24.0
C52, C54 to C56
C 1 1.0 2293 - 3642 - 5740 687 24.0
& C58 to C60
C25, C27, C29 &
D 1 1.0 3633 - 3633 - 4307 - 26.5
C31
D C33 1 1.0 3671 - 3671 - 4476 - 26.5
D C1 & C35 1 1.0 3781 - 4528 - 5425 - 26.5
E C19, C21 & C23 1 1.0 4157 - 4157 - 5203 - 28
F C17 & C51 1 1.0 4947 - 6086 - 7210 - 32.5
F C5, C6 & C39 1 1.0 5047 - 6278 - 8851 - 32.5
F C8 & C13 1 1.0 5089 - 5376 - 6378 - 32.5
C2, C3, C4, C36,
F 1 1.0 5180 - 5538 - 6641 - 32.5
C37 & C38
C7, C9 to C12 &
G 1 1.0 6076 - 7004 - 8260 - 36
C14
C15, C16, C49 &
H 1 1.0 6618 - 7175 - 8401 - 39
C50
I C40 1 1.2 5105 - 5105 - 6149 - 28
C41, C44, C46 &
J 1 1.2 6137 - 6848 - 10153 - 31.5
C47
C42, C43, C45 &
K 1 1.2 6673 - 7925 - 10764 - 33
C48
L PG2A 2 1.2 2507 - 5870 2277 7204 3053 26
L PG2 2 1.2 2761 - 5427 1963 7594 3570 26

TWJO-1-TCD-ST1- 0004-Rev A PAGE 40 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

No. of Pile Vertical Load per Pile (kN)


Load Column No(s). / Pile
Piles / Diameter Static ODE MDE
Category Pile Group Length (m)
Column (m) Compression Tension Compression Tension Compression Tension
M C34 4 1.2 4613 - 8284 1863 10294 2608 31
M C18 4 1.2 4789 - 8364 1912 11226 3480 31
C24, C26, C28 &
M 4 1.2 4869 - 8397 1859 10423 2826 31
C30
N C32 4 1.2 5189 - 8709 1516 10697 2224 32.5
N C20 & C22 4 1.2 5219 - 8500 1803 11299 2558 32.5

TWJO-1-TCD-ST1- 0004-Rev A PAGE 41 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

8.2 Bored Pile Design


The detailed bending moments and N-M interaction curves have been used to
design the structural reinforcement of pile.
Table 14 – Typical axial loads & moments for pile design
1
Typical values at pile top for column C10 Axial Load Resultant Moment
S.No. Load Case ID Category kN kN-m
1 L1 7203 1254
-1942 1277

MOMENTS & STATIC ULS


2 L2
3 L3 6655 1273
4 L4 -634 1060
5 L5 7080 896

MDE – FORCES &


6 L6 -1942 778
7 L7 7203 1254
8 L8 -1894 1292
9 L9 6904 1326
10 L10 CASES -1681 1363
11 L11 6655 1866
12 L12 -634 1763
13 L13 5869 997
14 L14 -1166 1020
15 L15 4857 548
16 L16 0 537
17 L17 5781 714
ODE – FORCES &

18 L18 -1166 621


19 L19 5869 997
MOMENTS

20 L20 -1132 1031


21 L21 5656 1054
22 L22 -979 1088
23 L23 4860 1042
24 L24 0 1057
25 L25 2507 103
26 L26 1633 33
STATIC SLS LOAD CASES

27 L27 2241 90
28 L28 2507 79
29 L29 2062 65
30 L30 1642 5
31 L31 2241 131
32 L32 2507 103
33 L33 1642 12
34 L34 2062 91
35 L35 2241 131
36 L36 2507 103

1
The negative values depicted in here refer to the tensile force in piles.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 42 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

8.2.1 Summary of Section Analysis


Section analysis using OASYS – Adsec, a section analysis program is carried out
using the concurrent forces. A typical section analysis results is shown in Table 11.

Table 15 – Typical analysis results of pile design


ULS Adequacy for MDE
N M Mu M/Mu
Case
[kN] [kNm] [kNm]
Maxima -634.5 1763 1969 0.895 OK
Minima 7080 896.1 3743 0.239 OK

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 65.47 OK
Minima -299.9 OK

SLS Stresses
Permissible Stresses Concrete 0.5fcu 20.000 Mpa
Steel 0.75fy 292.500 Mpa
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Stress in
Stress in Concrete
Case Reinforcement
[N/mm²] [N/mm²]
Maxima 2.63 OK 17.92 OK
Minima 1.141 OK 8.637 OK

8.2.2 Typical reinforcement section

Figure 26 – Typical reinforcement section of piles


The typical calculation procedure shown above is appended for different pile groups
in appendix. The reinforcement drawing has been further appended with the
package based on the analysis results.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 43 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

8.3 Structural Design of Pile Cap


The pile cap for all the columns are modelled with exact dimensions given in column
layout and is kept at 1.5m below the ground surface. The same has been modelled
in the STAAD Pro and its design has been carried out based on beam bending
theory.

Moment in
Pile Cap
1 2

Lever arm

3 4
PIER

PILE
LOAD

Figure 27 – Typical Pile cap schematic diagram


Table 16- Design moments in Pile Cap

Case M1 (kN.m) M = (M1 - M2) (kN.m)


MDE Seismic 16057.600 15470.782
ODE Seismic 13005.600 12495.324
Static 7236.000 6725.724

Based on the above evaluated moments under different combinations the


reinforcement has been evaluated and cross checked using OASYS section check
software.
Table 17 – Stress Check from OASYS
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 15470 20210 0.7656 OK
Minima
2 0.0 4488 17960 0.2499 OK

TWJO-1-TCD-ST1- 0004-Rev A PAGE 44 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Crack Width Check :-


Permissible crack width = 0.250 mm
Design surface crack width = 0.135 mm OK

8.3.1 Lateral deflection of pile cap top

The lateral or longitudinal deflections of entire structure have been depicted under
MDE conditions. The values are well acceptable under inter storey drift limits.

Lateral Displacement
No. of Pile at Pile Top (mm)
S. No. Column No(s). Piles / Diameter
Column (m) ODE
X Z
1 C1 1 1.0 29.612 39.675
2 C2 1 1.0 31.203 37.846
3 C3 1 1.0 30.285 39.29
4 C4 1 1.0 30.431 37.602
5 C5 1 1.0 29.946 38.93
6 C6 1 1.0 28.555 37.254
7 C7 1 1.0 32.231 38.405
8 C8 1 1.0 30.578 37.419
9 C9 1 1.0 30.345 38.726
10 C10 1 1.0 32.098 36.906
11 C11 1 1.0 31.568 38.344
12 C12 1 1.0 32.353 37.758
13 C13 1 1.0 30.113 36.313
14 C14 1 1.0 31.554 35.297
15 C15 1 1.0 31.659 38.495
16 C16 1 1.0 32.003 37.387
17 C17 1 1.0 30.209 39.079
18 C18 4 1.2 40.315 50.088

TWJO-1-TCD-ST1- 0004-Rev A PAGE 45 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

19 C19 1 1.0 33.591 39.887


20 C20 4 1.2 39.806 49.726
21 C21 1 1.0 32.833 39.617
22 C22 4 1.2 39.306 49.321
23 C23 1 1.0 32.651 38.975
24 C24 4 1.2 39.241 48.928
25 C25 1 1.0 32.489 38.661
26 C26 4 1.2 39.715 49.337
27 C27 1 1.0 32.756 39.162
28 C28 4 1.2 39.84 49.822
29 C29 1 1.0 32.765 39.003
30 C30 4 1.2 39.621 48.826
31 C31 1 1.0 32.847 38.674
32 C32 4 1.2 39.739 49.039
33 C33 1 1.0 33.097 39.32
34 C34 4 1.2 39.648 49.489
35 C35 1 1.0 31.631 39.664
36 C36 1 1.0 33.116 37.842
37 C37 1 1.0 32.106 39.295
38 C38 1 1.0 32.352 37.599
39 C39 1 1.0 31.523 39.063
40 C40 1 1.0 32.598 39.686
41 C41 1 1.0 31.471 41.309
42 C42 1 1.0 32.236 39.677
43 C43 1 1.0 31.206 40.549
44 C44 1 1.0 32.404 39.351
45 C45 1 1.0 30.983 39.466
46 C46 1 1.0 33.516 39.613
47 C47 1 1.0 31.137 40.471
48 C48 1 1.0 31.798 39.561
49 C49 1 1.0 30.793 38.877
50 C50 1 1.0 31.613 37.314
51 C51 1 1.0 29.78 39.054

TWJO-1-TCD-ST1- 0004-Rev A PAGE 46 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

9. SETTLEMENT OF PILES

9.1 Settlement Limit


It is anticipated that the total and differential pile settlement due to soil conditions
are less that those values considered in the design of the structure for serviceability.
The recommended allowable settlement developed based on Outline Design
Specification (ODS) is shown in Table 18.
Table 18 – Recommended Allowable Settlement for Buildings*

Maximum Allowable Settlement


Type of Structures
Short Term (mm) Long Term (mm)
Total settlement 10** 150
Differential settlement 1:1000 1:300
* Developed Based on ODS (PT MRTJ, 2012) and Jakarta’s regulation of Structural
and Geotechnical Design Guidelines for Buildings (Dinas Penataan dan
Pengawasan Bangunan DKI Jakarta, 2007)
** With the exception if any justification on structural element adequacy available

9.2 Pile Settlement Analysis


The settlement of piles shall be estimated using Tomlinson (1994).
(𝑊𝑠 + 2𝑊𝑏 )𝐿 𝜋 𝑊𝑏 𝐵(1 − 𝑣 2 )𝐼𝑝
𝑠= +
2𝐴𝑠 𝐸𝑝 4 𝐴𝑏 𝐸𝑏
Where,
Ws : Load in the pile shaft
Wb : Load in the pile base
As : Cross-sectional area of the shaft
Ab : Cross-sectional area of the base
Ep : Elastic modulus of the pile (Short Term)
Ep : Elastic modulus of the pile (Long Term)
Eb : Deformation modulus of soil beneath pile base
L : Shaft length
B : Pile width
 : Poisson’s ratio of the soil
IP : Influence factor related to the ratio of L/B
9.3 Group Pile Settlement
For group of piles, it is possible to link the settlements of single piles and pile groups
(Poulos, 1989). For general pile groups, the group settlement ratio Rs, defined as
𝑠𝑒𝑡𝑡𝑙𝑒𝑚𝑒𝑛𝑡 𝑜𝑓 𝑔𝑟𝑜𝑢𝑝
𝑅𝑠 =
𝑠𝑒𝑡𝑡𝑙𝑒𝑚𝑒𝑛𝑡 𝑜𝑓 𝑠𝑖𝑛𝑔𝑙𝑒 𝑝𝑖𝑙𝑒 𝑎𝑡 𝑡ℎ𝑒 𝑠𝑎𝑚𝑒 𝑎𝑣𝑒𝑟𝑎𝑔𝑒 𝑙𝑜𝑎𝑑
Fleming et al. (1985) have presented results which suggest that Rs can be
approximated as follows,

TWJO-1-TCD-ST1- 0004-Rev A PAGE 47 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

𝑅𝑠 = 𝑛𝜔
Where n is the number of piles and is an exponent which lies between 0.4 and 0.6
for most pile groups.

9.4 Consolidation Settlement


There would be negligible consolidation settlement of the group since the piles in
groups are designed to be embedded in hard soils (SPT-N > 50). Further, no soft to
stiff compressible clay layer found in 3 times of pile group length below the pile toe.
If the consolidation settlement is applicable for a site, pile-raft foundation theory will
be used for the analysis.

Figure 28 – Pile-raft foundation to estimate load distribution for consolidation


settlement analysis, if applicable (Das, 2011)

9.5 Result of Analysis


The immediate pile settlement of designed pile length in both short and long term
analyses falls within the tolerable limiting value as shown in Table 12. The detailed
calculation of the pile settlement and its summary are presented in Appendices D
and E, respectively.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 48 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Table 19 – Summary of Pile Settlement

TOTAL PILE PILE GROUP


PILE SETTLEMENT SETTLEMENT
COLUMN NO OF DIAMETER BOREHOLE AT WORKING AT WORKING LOAD
NO PILES REFERENCE LOAD LOAD CATEGORY

(mm) (mm) (mm)

PG1A 1 1000 1 ABH-4 0.2 0.0 A

C53 1 1000 1 ABH-4 0.5 0.0 B

C57 1 1000 1 ABH-4 1.3 0.0 C

C52, C54
to C56 &
1 1000 1 ABH-4 1.3 0.0 C
C58 to
C60
C25, C27,
C29 & 1 1000 1 ABH-4 2.3 0.0 D
C31

C33 1 1000 1 ABH-4 2.3 0.0 D

C1 & C35 1 1000 1 ABH-4 2.3 0.0 D

C19, C21
1 1000 1 ABH-4 2.6 0.0 E
& C23

C17 &
1 1000 1 ABH-4 3.8 0.0 F
C51

C5, C6 &
1 1000 1 ABH-4 3.8 0.0 F
C39

C8 & C13 1 1000 1 ABH-4 3.8 0.0 F

C2, C3,
C4, C36,
1 1000 1 ABH-4 3.8 0.0 F
C37 &
C38

TWJO-1-TCD-ST1- 0004-Rev A PAGE 49 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

TOTAL PILE PILE GROUP


PILE SETTLEMENT SETTLEMENT
COLUMN NO OF DIAMETER BOREHOLE AT WORKING AT WORKING LOAD
NO PILES REFERENCE LOAD LOAD CATEGORY

(mm) (mm) (mm)

C7, C9 to
C12 & 1 1000 1 ABH-4 5.0 0.0 G
C14
C15, C16,
C49 & 1 1000 1 ABH-4 5.9 0.0 H
C50

C40 1 1200 1 ABH-4 2.3 0.0 I

C41, C44,
C46 & 1 1200 1 ABH-4 3.1 0.0 J
C47
C42, C43,
C45 & 1 1200 1 ABH-4 3.5 0.0 K
C48

PG2A 2 1200 1 ABH-4 1.1 1.6 L

PG2 2 1200 1 ABH-4 1.1 1.6 L

C34 4 1200 1 ABH-4 2.4 4.8 M

C18 4 1200 1 ABH-4 2.4 4.8 M

C24, C26,
C28 & 4 1200 1 ABH-4 2.4 4.8 M
C30

C32 4 1200 1 ABH-4 2.7 5.4 N

C20 &
4 1200 1 ABH-4 2.7 5.4 N
C22

TWJO-1-TCD-ST1- 0004-Rev A PAGE 50 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Figure 29 – Contour of Pile Settlement

TWJO-1-TCD-ST1- 0004-Rev A PAGE 51 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

TWJO-1-TCD-ST1- 0004-Rev A PAGE 52 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

10. CONCLUSION
All edge grid columns (along grids A & C) are founded on 1000/1200mm diameter
bored mono piles. Along grid B, viaduct-supporting columns are founded on groups
of four 1200mm diameter bored piles each, and the rest of the columns are founded
on 1200mm diameter piles. The design pile loads are summarized below.
The diameter and no. of piles to be provided for each column has been deciphered
based on the above loads and the available pile capacities. The moments from
STAAD PRO have been combined with these axial effects to design the
reinforcement for each pile using OASYS. The design calculations have been
attached with this report as appendices.

Factor of safety for axial bearing capacity of pile foundation has been designed to
comply with BS 8004 and Jakarta’s regulation of Structural and Geotechnical Design
Guidelines for Buildings (Dinas Penataan dan Pengawasan Bangunan DKI Jakarta,
2007).
Allowable lateral displacements for piles is designed be consistent with the function
and type of structure, the anticipated service life, and the consequences of
unacceptable displacements on the performance of the structure.
The anticipated total and differential pile settlement due to soil conditions are
designed to be less that those values considered in the design of the structure for
serviceability. There would be negligible consolidation settlement of the group since
the piles in groups are designed to be embedded in hard soils (SPT-N > 50), and no
soft to stiff compressible clay layer found in 3 times of pile group length below the
pile toe.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 53 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

11. REFERENCES

1) ACI Committee 336. (1972) “Suggested Design and Construction Procedures


for Pier Foundations”, Journal of the American Concrete Institute.
2) AECOM, (2014), Geotechnical Interpretative Report, Doc. No. AECOM-CP12-
TCD-DSR-0001-Rev 2.
3) AECOM, (2014), Design Manual for Civil and Structures, Doc. No. TWJO-
CP12-TCD-DSM-0001-Rev 2.
4) Bjerrum, L., and Simons, N.E. (1960). Comparison of Shear Strength
Characteristics of Normally Consolidated Clays, Proceedings of the ASCE
research Conference on the Shear Strength of Cohesive Soils, Boulder, pp.
711-726.
5) Boulanger, R.W and Idriss, I.M. (2007). Evaluation of Cyclic Softening in Silts
and Clays, Journal of Geotechnical and Geoenvironmental Engineering, ASCE,
Vol. 133, pp. 641-652.
6) Broms, B.B (1964), Lateral resistance of piles in cohesive soils, ASCE J. Soil
Mech. And Found. Div., 90(SM2): 27-63.
7) BS8004, (1986). Code of Practice for Foundations.
8) Casagrande, A. (1938). Notes on Soil Mechanics-First Semester, Harvard
University (unpublished), 129 pp.
9) Fardis, M., Carvalho, E., Elnashai, A., Faccioli, E., Pinto, P. and Plumier, A.
(2005). Designers’ Guide to EN 1998-1 and EN 1998-5 Eurocode 8: Design of
Structures for Earthquake Resistance, Thomas Telford, London.
10) Fauzi, A, Irsyam, M and Fauzi, U. J. (2014). Empirical Correlation of Shear
Wave Velocity and N-SPT Value For Jakarta. International Journal of
GEOMATE, Vol. 7, No. 1 (S1. No. 13), pp. 980-984.
11) Fleming, K., Weltman, A., Randolph, M., and Elson, K., (2009). Piling
Engineering 3rd Edition, Taylor & Francis, Oxon.
12) Imai, T., and Tonouchi, K., (1982). Correlation of N-value with S-wave velocity,
Proceedings of 2nd European Symposium on Penetration Testing, pp. 67-72.
13) Peck, R.B., Hanson, W.E. and Thornburn, T.H (1974). Foundation Engineering,
2nd edn., Wiley, New York.
14) Peraturan Kepala Dinas Penataan dan Pengawasan Bangunan Propinsi DKI
Jakarta (2007). Pedoman Perencanaan Struktur dan Geoteknik Bangunan, No.
50.
15) PT Mass Rapid Transit Jakarta (2012). Tender Documents for Construction of
Jakarta Mass Rapid Transit Project, Vol. 4: Employer's Requirements - Outline
Design Specifications and Appendices, Republic of Indonesia.
16) Rudianto, S. and Soedjono, B. (2009). Diskusi Load Transfer Bored Pile (Studi
Kasus di Jakarta), Pertemuan Ilmah Tahunan – XII HATTI, Bali.
17) SNI (2002). Design method of earthquake resistance for buildings. Badan
Standardisasi Nasional, Indonesia.
18) SNI (2012). Procedure of earthquake resistance design for building and non-
building structure. Badan Standardisasi Nasional, Indonesia.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 54 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

19) Stroud, M A (1989). The Standard Penetration Test – Its Application and
Interpretation, Proceedings of ICE Conference, Birmingham.
20) Toha, F.X. and Sengara, I.W. (2009). Consolidation Settlements of Deep Clay
Layers under High Rise Buildings in Jakarta, Development of Geotechnical
Engineering in Civil Construction, Bali, Indonesia, pp 22-36.
21) Tomlinson, M.J., (1994). Pile Design and Construction Practice, 4th Ed., Taylor
& Francis, Oxon.
22) Vesic, A. S. (1961a). Bending Beams Resting on Isotropic Elastic Solid, Jour.
Eng. Mech. Division, ASCE, vol. 87, EM 2, April, pp. 35-53.
23) Vesic, A. S. (1961b). Beams on Elastic Subgrade and the Winkler’s Hypothesis,
5th ICSMFE, vil 1, pp. 845-850.

TWJO-1-TCD-ST1- 0004-Rev A PAGE 55 / 55


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix A

Geological Profile at CP101 (Lebak Bulus Station)

TWJO-1-TCD-ST1-0004-Rev A Appendix A
E-100
1ABH-4 1ABH-6 E-140
1ABH-5
1ABH-3 E-150
1ABH-2
E-110 Fence(Type1)
Shop in Track Gate House
E-120
E-130
AE-03 (Gantry Crane)

(Stock Yard)
AE-04
CO
NC
RE

AE-02
T E
Back Gate
1AD-1 Domestic Wastewater Treatment Shed

1ABH-1 Hazardous Store Industrial Wastewater Treatment Shed (Wheel Turning

Infrastructure Maintenence Garage


Shop)
(Emergency Repair Shop) 1AD-5
Fire Strage Tank & Pump House D-120
Inspection Shed
Water Strage Tank & Pump House (Train Inspection Shop) (Space for future)
(Train Inspection Shop)

Car Parking
Motorbike Parking2 (Space for future)
1AD-8
Fence(Type1)
Workshop Main Building
AE-01 D-110 Fence(Type1)
Workshop
Emergency Exit Office
Building
Site Administration Car Garage1 Fuel Tank
Office
Car Parking Car Parking

Garbage Collection Site Main Gate

9. -1

7. -2

9. -3

8. -4

6. -6
9. -5
6. 1

0. 2

+3 100

+3 110

+3 120
+2 B H

+3 B H

+3 B H

+3 B H
+2 E-0

+3 E-0

+3 B H
8

+3 B H
32

67

+3 130

+3 140

+3 150
3
29

92

50

12

51

36

83

4
51
1A

1A

1A

1A

41
E-

E-

E-

61

61

58
1A
A

1A
5.

4.

8.

E-

E-

E-
9.

5.

7.
NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


PT MRT Jakarta Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


SOIL PROFILE
Km 0-600 TO Km 0+600
PRESIDENT DIRECTOR
VERIFIED BY SHEET 3
DIRECTOR OF
CONSTRUCTION
DESIGNED BY
AS SHOWN 1/CWD/GTE/2013 - T
PROJECT MANAGER
PT. AECOM INDONESIA 1CWDGTE2011-2013.dwg

O:\60313051\TR\Technical Stage\GTE\1CWDGTE2011-2013.dwg, 3/7/2014 6:29:48 PM, PDF-XChange 4 Jakarta_A1.pc3


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix B

Site Zoning & SPT-N Design Line

TWJO-1-TCD-ST1-0004-Rev A Appendix B
SPT-N Value
0 5 10 15 20 25 30 35 40 45 50 55 60
0

10

15
Depth below Ground Level (mbgl)

20

25

30

35

40 E-120

1ABH4

1ABH5
45
Moderately Conservative Design Line

Most Probable Design Line

50

PROJECT TITLE:- ORIGINATOR:-

Engineering Consulting Services for Jakarta


Mass Rapid Transit System Project (IP-536)
(CP101 to CP102) SKETCH / FIG No.:-

SKETCH / FIG TITLE:- REPORT No.:-

Pile Zoning Profile


Station Lebak Bulus DATE:-

Oct-14
SOIL LATERAL SPRING CONSTANT - LEBAK BULUS STATION

Unit Pile Diameter, D


Description
m 1
Pile Stiffness, Ep kN/m2 31,000,000
Pile Inertia, I m4 0.0491
Soil Poisson Ratio, v - 0.3

Based on Moderately Conservative Design Line


Modulus of Subgrade
Soil Layer Stiffness Soil Spring Constant, ks
SPT-N Reaction, KH
Modulus
Top Bottom Static Seismic Static Seismic
(m) (m) - (kN/m2) (kN/m2) (kN/m2) (kN/m) (kN/m)
0 1 3 4,500 1,979 1,385 1,979 1,385
1 2 3 4,500 1,979 1,385 1,979 1,385
2 3 3 4,500 1,979 1,385 1,979 1,385
3 4 3 4,500 1,979 1,385 1,979 1,385
4 5 3 4,500 1,979 1,385 1,979 1,385
5 6 3 4,500 1,979 1,385 1,979 1,385
6 7 3 4,500 1,979 1,385 1,979 1,385
7 8 3 4,500 1,979 1,385 1,979 1,385
8 9 5 7,500 3,441 2,409 3,441 2,409
9 10 5 7,500 3,441 2,409 3,441 2,409
10 11 5 7,500 3,441 2,409 3,441 2,409
11 12 5 7,500 3,441 2,409 3,441 2,409
12 13 5 7,500 3,441 2,409 3,441 2,409
13 14 5 7,500 3,441 2,409 3,441 2,409
14 15 5 7,500 3,441 2,409 3,441 2,409
15 16 8 12,000 5,725 4,008 5,725 4,008
16 17 8 12,000 5,725 4,008 5,725 4,008
17 18 15 22,500 11,313 7,919 11,313 7,919
18 19 15 22,500 11,313 7,919 11,313 7,919
19 20 15 22,500 11,313 7,919 11,313 7,919
20 21 15 22,500 11,313 7,919 11,313 7,919
21 22 50 75,000 41,688 29,182 41,688 29,182
22 23 50 75,000 41,688 29,182 41,688 29,182
23 24 50 75,000 41,688 29,182 41,688 29,182
24 25 50 75,000 41,688 29,182 41,688 29,182
25 26 50 75,000 41,688 29,182 41,688 29,182
26 27 50 75,000 41,688 29,182 41,688 29,182
27 28 50 75,000 41,688 29,182 41,688 29,182
28 29 50 75,000 41,688 29,182 41,688 29,182
29 30 50 75,000 41,688 29,182 41,688 29,182
30 31 50 75,000 41,688 29,182 41,688 29,182
31 32 50 75,000 41,688 29,182 41,688 29,182
32 33 50 75,000 41,688 29,182 41,688 29,182
33 34 50 75,000 41,688 29,182 41,688 29,182
34 35 50 75,000 41,688 29,182 41,688 29,182
35 36 50 75,000 41,688 29,182 41,688 29,182
36 37 50 75,000 41,688 29,182 41,688 29,182
37 38 50 75,000 41,688 29,182 41,688 29,182
38 39 50 75,000 41,688 29,182 41,688 29,182
39 40 50 75,000 41,688 29,182 41,688 29,182
* The Modulus of Subgrade Reaction are derived from Vesic's formula to be duly verified by
result of preliminary lateral pile test.
** Pile design shall be based on moderately conservative design parameter.
SOIL LATERAL SPRING CONSTANT - LEBAK BULUS STATION

Unit Pile Diameter, D


Description
m 1.2
Pile Stiffness, Ep 2 31,000,000
kN/m
4 0.1017
Pile Inertia, I m
Soil Poisson Ratio, v - 0.3

Based on Moderately Conservative Design Line


Modulus of Subgrade
Soil Layer Stiffness Soil Spring Constant, ks
SPT-N Reaction, KH
Modulus
Top Bottom Static Seismic Static Seismic
2 2 2
(m) (m) - (kN/m ) (kN/m ) (kN/m ) (kN/m) (kN/m)
0 1 3 4,500 1,979 1,385 1,979 1,385
1 2 3 4,500 1,979 1,385 1,979 1,385
2 3 3 4,500 1,979 1,385 1,979 1,385
3 4 3 4,500 1,979 1,385 1,979 1,385
4 5 3 4,500 1,979 1,385 1,979 1,385
5 6 3 4,500 1,979 1,385 1,979 1,385
6 7 3 4,500 1,979 1,385 1,979 1,385
7 8 3 4,500 1,979 1,385 1,979 1,385
8 9 5 7,500 3,441 2,409 3,441 2,409
9 10 5 7,500 3,441 2,409 3,441 2,409
10 11 5 7,500 3,441 2,409 3,441 2,409
11 12 5 7,500 3,441 2,409 3,441 2,409
12 13 5 7,500 3,441 2,409 3,441 2,409
13 14 5 7,500 3,441 2,409 3,441 2,409
14 15 5 7,500 3,441 2,409 3,441 2,409
15 16 8 12,000 5,725 4,008 5,725 4,008
16 17 8 12,000 5,725 4,008 5,725 4,008
17 18 15 22,500 11,313 7,919 11,313 7,919
18 19 15 22,500 11,313 7,919 11,313 7,919
19 20 15 22,500 11,313 7,919 11,313 7,919
20 21 15 22,500 11,313 7,919 11,313 7,919
21 22 50 75,000 41,688 29,182 41,688 29,182
22 23 50 75,000 41,688 29,182 41,688 29,182
23 24 50 75,000 41,688 29,182 41,688 29,182
24 25 50 75,000 41,688 29,182 41,688 29,182
25 26 50 75,000 41,688 29,182 41,688 29,182
26 27 50 75,000 41,688 29,182 41,688 29,182
27 28 50 75,000 41,688 29,182 41,688 29,182
28 29 50 75,000 41,688 29,182 41,688 29,182
29 30 50 75,000 41,688 29,182 41,688 29,182
30 31 50 75,000 41,688 29,182 41,688 29,182
31 32 50 75,000 41,688 29,182 41,688 29,182
32 33 50 75,000 41,688 29,182 41,688 29,182
33 34 50 75,000 41,688 29,182 41,688 29,182
34 35 50 75,000 41,688 29,182 41,688 29,182
35 36 50 75,000 41,688 29,182 41,688 29,182
36 37 50 75,000 41,688 29,182 41,688 29,182
37 38 50 75,000 41,688 29,182 41,688 29,182
38 39 50 75,000 41,688 29,182 41,688 29,182
39 40 50 75,000 41,688 29,182 41,688 29,182
* The Modulus of Subgrade Reaction are derived from Vesic's formula to be duly verified by result of preliminary lateral pile test.
** Pile design shall be based on moderately conservative design parameter.
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix C

Pile Schedule

TWJO-1-TCD-ST1-0004-Rev A Appendix C
PILE SCHEDULE FOR STATIONS
SUMMARY_ LEBAK BULUS STATION
BORED PILE SCHEDULE
STATIC WORKING LOAD / PILE ODE LOAD / PILE MDE LOAD / PILE MIN. PILE SOCKET
MIN PILE
PILE NEGATIVE SKIN PILE CUT-OFF MIN. PILE LENGTH INTO
NO. OF BOREHOLE LENGTH
COLUMN NO. DIAMETER FRICTION LEVEL TOE LEVEL BEARING LAYER
PILES REFERENCE COMPRESSION TENSION COMPRESSION TENSION COMPRESSION TENSION (FROM COL)
SPT-N > 50

(mm) (kN) (kN) (kN) (kN) (kN) (kN) (kN) (mRL) (mRL) (m) (m)
PG1B 1 1.0 1 ABH-4 692 - 802 - 1150 - 0 35.275 24.275 11.0 0.0
C53 1 1.0 1 ABH-4 1121 - 3217 1270 3948 1694 0 35.275 13.775 21.5 0.0

C57 1 1.0 1 ABH-4 2132 - 4054 718 6757 2271 0 35.275 11.275 24.0 1.1
C52, C54 to C56 &
1 1.0 1 ABH-4 2293 - 3642 - 5740 687 0 35.275 11.275 24.0 1.1
C58 to C60
C25, C27, C29 & C31 1 1.0 1 ABH-4 3633 - 3633 - 4307 - 0 35.275 8.775 26.5 3.6

C33 1 1.0 1 ABH-4 3671 - 3671 - 4476 - 0 35.275 8.775 26.5 3.6

C1 & C35 1 1.0 1 ABH-4 3781 - 4528 - 5425 - 0 35.275 8.775 26.5 3.6

C19, C21 & C23 1 1.0 1 ABH-4 4157 - 4157 - 5203 - 0 35.275 7.275 28.0 5.1

C17 & C51 1 1.0 1 ABH-4 4947 - 6086 - 7210 - 0 35.275 2.775 32.5 9.6

C5, C6 & C39 1 1.0 1 ABH-4 5047 - 6278 - 8851 - 0 35.275 2.775 32.5 9.6

C8 & C13 1 1.0 1 ABH-4 5089 - 5376 - 6378 - 0 35.275 2.775 32.5 9.6

C2, C3, C4, C36, C37


1 1.0 1 ABH-4 5180 - 5538 - 6641 - 0 35.275 2.775 32.5 9.6
& C38

C7, C9 to C12 & C14 1 1.0 1 ABH-4 6076 - 7004 - 8260 - 0 35.275 -0.725 36.0 13.1

C15, C16, C49 & C50 1 1.0 1 ABH-4 6618 - 7175 - 8401 - 0 35.275 -3.725 39.0 16.1

C40 1 1.2 1 ABH-4 5105 - 5105 - 6149 - 0 34.975 6.975 28.0 5.4

C41, C44, C46 & C47 1 1.2 1 ABH-4 6137 - 6848 - 10153 - 0 34.975 3.475 31.5 8.9

C42, C43, C45 & C48 1 1.2 1 ABH-4 6673 - 7925 - 10764 - 0 34.975 1.975 33.0 10.4

PG2A 2 1.2 1 ABH-4 2507 - 5870 2277 7204 3053 0 34.975 8.975 26.0 3.4

PG2 2 1.2 1 ABH-4 2761 - 5427 1963 7594 3570 0 34.975 8.975 26.0 3.4

C34 4 1.2 1 ABH-4 4613 - 8284 1863 10294 2608 0 34.975 3.975 31.0 8.4

C18 4 1.2 1 ABH-4 4789 - 8364 1912 11226 3480 0 34.975 3.975 31.0 8.4

C24, C26, C28 & C30 4 1.2 1 ABH-4 4869 - 8397 1859 10423 2826 0 34.975 3.975 31.0 8.4

C32 4 1.2 1 ABH-4 5189 - 8709 1516 10697 2224 0 34.975 2.475 32.5 9.9

C20 & C22 4 1.2 1 ABH-4 5219 - 8500 1803 11299 2558 0 34.975 2.475 32.5 9.9
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix D

Calculation Sheet for Pile Axial Bearing Capacity

TWJO-1-TCD-ST1-0004-Rev A Appendix D
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category: 1x1000 Load Category: A
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : 24.28 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 24.28 37 0.1 148 148 41 41 1

Total 11.0 1489 1421

Ultimate Skin Friction, Qs (kN) = 1,489 1,421

B) END BEARING
Pile Depth 11.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe AC3 Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 1,767

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 1,303 745 947 3,188 496 710 947

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 745 kN Static (kN) 692 OK 0
ODE 947 kN ODE (kN) 802 OK 0
MDE 3,188 kN MDE (kN) 1150 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category: 1x1000 Load Category: A
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 692 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 11.0 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 0.17 mm
2) Long Term Settlement 0.35 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 0.17 mm
2) Long Term Settlement 0.35 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category 1x1000


: Load Category: B
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : 13.78 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.78 45.5 3.1 137 137 1,325 1,325 1

Total 21.5 5015 4947

Ultimate Skin Friction, Qs (kN) = 5,015 4,947

B) END BEARING
Pile Depth 21.5 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TS Unit End Bearing 3000 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 60

Ultimate End bearing, Qb (kN) = 2,356

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 2,949 2,508 3,298 7,303 1,672 2,473 3,298

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 2,508 kN Static (kN) 1121 OK 0
ODE 3,298 kN ODE (kN) 3217 OK 1270 OK
MDE 7,303 kN MDE (kN) 3948 OK 1694 OK
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: B
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 1,121 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 21.5 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 0.55 mm
2) Long Term Settlement 1.10 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 0.55 mm
2) Long Term Settlement 1.10 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category1x1000


: Load Category: C
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : 11.28 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.36 45.5 3.5 137 137 1,501 1,501 1
TC 13.36 12.36 48 1.0 192 192 603 603 1
TC 12.36 11.28 50 1.1 200 200 684 684 1

Total 24.0 6479 6411

Ultimate Skin Friction, Qs (kN) = 6,479 6,411

B) END BEARING
Pile Depth 24.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 1,767

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 3,298 3,239 4,274 8,178 2,160 3,205 4,274

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 3,239 kN Static (kN) 2293 OK 0
ODE 4,274 kN ODE (kN) 4054 OK 718 OK
MDE 8,178 kN MDE (kN) 6757 OK 2271 OK
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: C
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 2,293 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 24.0 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 1.25 mm
2) Long Term Settlement 2.50 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 1.25 mm
2) Long Term Settlement 2.50 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category1x1000


: Load Category: D
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : 8.78 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.36 45.5 3.5 137 137 1,501 1,501 1
TC 13.36 12.36 48 1.0 192 192 603 603 1
TC 12.36 11.36 50 1.0 200 200 628 628 1
TS 11.36 9.36 50 2.0 150 150 942 942 1
TC 9.36 8.78 48.75 0.6 195 195 361 361 1

Total 26.5 7726 7658

Ultimate Skin Friction, Qs (kN) = 7,726 7,658

B) END BEARING
Pile Depth 26.5 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 1,767

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 3,797 3,863 5,105 9,425 2,575 3,829 5,105

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 3,797 kN Static (kN) 3781 OK 0
ODE 5,105 kN ODE (kN) 4528 OK 0
MDE 9,425 kN MDE (kN) 5425 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: D
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 3,781 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 26.5 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 2.28 mm
2) Long Term Settlement 4.56 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 2.28 mm
2) Long Term Settlement 4.56 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category1x1000


: Load Category: E
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : 7.28 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.36 45.5 3.5 137 137 1,501 1,501 1
TC 13.36 12.36 48 1.0 192 192 603 603 1
TC 12.36 11.36 50 1.0 200 200 628 628 1
TS 11.36 9.36 50 2.0 150 150 942 942 1
TC 9.36 7.28 48.75 2.1 195 195 1,280 1,280 1

Total 28.0 8645 8577

Ultimate Skin Friction, Qs (kN) = 8,645 8,577

B) END BEARING
Pile Depth 28.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 1,767

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 4,165 4,323 5,718 10,344 2,882 4,288 5,718

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 4,165 kN Static (kN) 4157 OK 0
ODE 5,718 kN ODE (kN) 4157 OK 0
MDE 10,344 kN MDE (kN) 5203 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: E
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4
Load in the pile shaft Ws 4,157 kN
Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 28.0 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 2.65 mm
2) Long Term Settlement 5.29 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 2.65 mm
2) Long Term Settlement 5.29 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: F
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : 2.78 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.36 45.5 3.5 137 137 1,501 1,501 1
TC 13.36 12.36 48 1.0 192 192 603 603 1
TC 12.36 11.36 50 1.0 200 200 628 628 1
TS 11.36 9.36 50 2.0 150 150 942 942 1
TC 9.36 2.78 48.75 6.6 195 195 4,036 4,036 1

Total 32.5 11402 11334

Ultimate Skin Friction, Qs (kN) = 11,402 11,334

B) END BEARING
Pile Depth 32.5 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 1,767

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 5,268 5,701 7,556 13,101 3,801 5,667 7,556

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 5,268 kN Static (kN) 5180 OK 0
ODE 7,556 kN ODE (kN) 6278 OK 0
MDE 12,566 kN MDE (kN) 8851 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: F
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 5,180 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 32.5 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 3.83 mm
2) Long Term Settlement 7.66 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 3.83 mm
2) Long Term Settlement 7.66 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category :1x1000 Load Category: G
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : -0.73 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.36 45.5 3.5 137 137 1,501 1,501 1
TC 13.36 12.36 48 1.0 192 192 603 603 1
TC 12.36 11.36 50 1.0 200 200 628 628 1
TS 11.36 9.36 50 2.0 150 150 942 942 1
TC 9.36 2.36 48.75 7.0 195 195 4,288 4,288 1
TS 2.36 -0.73 45.25 3.1 136 136 1,317 1,317 1

Total 36.0 12971 12903

Ultimate Skin Friction, Qs (kN) = 12,971 12,903

B) END BEARING
Pile Depth 36.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TS Unit End Bearing 3000 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 60

Ultimate End bearing, Qb (kN) = 2,356

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 6,131 6,486 8,602 15,259 4,324 6,451 8,602

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 6,131 kN Static (kN) 6076 OK 0
ODE 7,854 kN ODE (kN) 7004 OK 0
MDE 12,566 kN MDE (kN) 8260 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: G
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) (1 2)
+2
= +
2 4

Load in the pile shaft Ws 6,076 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 36.0 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 4.97 mm
2) Long Term Settlement 9.95 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 4.97 mm
2) Long Term Settlement 9.95 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: H
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.00 m
w : 9.8 kN/m3 Pile Cut-off Level : 35.275 mRL
Pile Toe Level : -3.73 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 35.28 28.36 3.5 6.9 16 13 342 274 1
AC3 28.36 24.36 22 4.0 88 88 1,106 1,106 1
AC3 24.36 22.36 37 2.0 148 148 930 930 1
AC3 22.36 21.91 47 0.4 188 188 266 266 1
AC3 21.91 16.86 16.5 5.1 66 66 1,047 1,047 1
TS 16.86 13.36 45.5 3.5 137 137 1,501 1,501 1
TC 13.36 12.36 48 1.0 192 192 603 603 1
TC 12.36 11.36 50 1.0 200 200 628 628 1
TS 11.36 9.36 50 2.0 150 150 942 942 1
TC 9.36 2.36 48.75 7.0 195 195 4,288 4,288 1
TS 2.36 -3.73 45.25 6.1 136 136 2,597 2,597 1

Total 39.0 14251 14182

Ultimate Skin Friction, Qs (kN) = 14,251 14,182

B) END BEARING
Pile Depth 39.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TS Unit End Bearing 3000 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 0.79 m²
End Bearing Multiplier 60

Ultimate End bearing, Qb (kN) = 2,356

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.3 31.1 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 6,643 7,125 9,455 16,538 4,750 7,091 9,455

E) STRUCTURAL CAPACITY
Static 7,854 kN
ODE 7,854 kN
MDE 12,566 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 6,643 kN Static (kN) 6618 OK 0
ODE 7,854 kN ODE (kN) 7175 OK 0
MDE 12,566 kN MDE (kN) 8401 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1000 Load Category: H
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 6,618 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 0.79 m²
Cross-sectional area of the base Ab 0.79 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 39.0 m
Pile width B 1.00 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 5.87 mm
2) Long Term Settlement 11.74 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 5.87 mm
2) Long Term Settlement 11.74 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category:1x1200 Load Category: I
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.20 m
w : 9.8 kN/m3 Pile Cut-off Level : 34.975 mRL
Pile Toe Level : 6.98 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 34.98 28.36 3.5 6.6 16 13 393 314 1
AC3 28.36 24.36 22 4.0 88 88 1,327 1,327 1
AC3 24.36 22.36 37 2.0 148 148 1,116 1,116 1
AC3 22.36 21.91 47 0.4 188 188 319 319 1
AC3 21.91 16.86 16.5 5.1 66 66 1,257 1,257 1
TS 16.86 13.36 45.5 3.5 137 137 1,801 1,801 1
TC 13.36 12.36 48 1.0 192 192 724 724 1
TC 12.36 11.36 50 1.0 200 200 754 754 1
TS 11.36 9.36 50 2.0 150 150 1,131 1,131 1
TC 9.36 6.98 48.75 2.4 195 195 1,756 1,756 1

Total 28.0 10577 10498

Ultimate Skin Friction, Qs (kN) = 10,577 10,498

B) END BEARING
Pile Depth 28.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 1.13 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 2,545

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.0 31.0 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 5,249 5,288 6,999 13,043 3,526 5,249 6,999

E) STRUCTURAL CAPACITY
Static 11,310 kN
ODE 11,310 kN
MDE 18,096 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 5,249 kN Static (kN) 5105 OK 0
ODE 6,999 kN ODE (kN) 5105 OK 0
MDE 13,043 kN MDE (kN) 6149 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category: 1x1200 Load Category: I
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) (1 2)
+2
= +
2 4

Load in the pile shaft Ws 5,105 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 1.13 m²
Cross-sectional area of the base Ab 1.13 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 28.0 m
Pile width B 1.20 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 2.26 mm
2) Long Term Settlement 4.51 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 2.26 mm
2) Long Term Settlement 4.51 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category1x1200


: Load Category: J
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.20 m
w : 9.8 kN/m3 Pile Cut-off Level : 34.975 mRL
Pile Toe Level : 3.48 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 34.98 28.36 3.5 6.6 16 13 393 314 1
AC3 28.36 24.36 22 4.0 88 88 1,327 1,327 1
AC3 24.36 22.36 37 2.0 148 148 1,116 1,116 1
AC3 22.36 21.91 47 0.4 188 188 319 319 1
AC3 21.91 16.86 16.5 5.1 66 66 1,257 1,257 1
TS 16.86 13.36 45.5 3.5 137 137 1,801 1,801 1
TC 13.36 12.36 48 1.0 192 192 724 724 1
TC 12.36 11.36 50 1.0 200 200 754 754 1
TS 11.36 9.36 50 2.0 150 150 1,131 1,131 1
TC 9.36 3.48 48.75 5.9 195 195 4,329 4,329 1

Total 31.5 13150 13071

Ultimate Skin Friction, Qs (kN) = 13,150 13,071

B) END BEARING
Pile Depth 31.5 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 1.13 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 2,545

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.0 31.0 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 6,278 6,575 8,714 15,616 4,383 6,536 8,714

E) STRUCTURAL CAPACITY
Static 11,310 kN
ODE 11,310 kN
MDE 18,096 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 6,278 kN Static (kN) 6137 OK 0
ODE 8,714 kN ODE (kN) 6848 OK 0
MDE 15,616 kN MDE (kN) 10153 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 1x1200 Load Category: J
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 6,137 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 1.13 m²
Cross-sectional area of the base Ab 1.13 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 31.5 m
Pile width B 1.20 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 3.05 mm
2) Long Term Settlement 6.10 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 3.05 mm
2) Long Term Settlement 6.10 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category: 1x1200 Load Category: K
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.20 m
w : 9.8 kN/m3 Pile Cut-off Level : 34.975 mRL
Pile Toe Level : 1.98 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 34.98 28.36 3.5 6.6 16 13 393 314 1
AC3 28.36 24.36 22 4.0 88 88 1,327 1,327 1
AC3 24.36 22.36 37 2.0 148 148 1,116 1,116 1
AC3 22.36 21.91 47 0.4 188 188 319 319 1
AC3 21.91 16.86 16.5 5.1 66 66 1,257 1,257 1
TS 16.86 13.36 45.5 3.5 137 137 1,801 1,801 1
TC 13.36 12.36 48 1.0 192 192 724 724 1
TC 12.36 11.36 50 1.0 200 200 754 754 1
TS 11.36 9.36 50 2.0 150 150 1,131 1,131 1
TC 9.36 2.36 48.75 7.0 195 195 5,146 5,146 1
TS 2.36 1.98 45.25 0.4 136 136 199 199 1

Total 33.0 14166 14087

Ultimate Skin Friction, Q s (kN) = 14,166 14,087

B) END BEARING
Pile Depth 33.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TS Unit End Bearing 3000 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 1.13 m²
End Bearing Multiplier 60

Ultimate End bearing, Qb (kN) = 3,393

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.0 31.0 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 7,023 7,083 9,391 17,480 4,722 7,044 9,391

E) STRUCTURAL CAPACITY
Static 11,310 kN
ODE 11,310 kN
MDE 18,096 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 7,023 kN Static (kN) 6673 OK 0
ODE 9,391 kN ODE (kN) 7925 OK 0
MDE 17,480 kN MDE (kN) 10764 OK 0
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category: 1x1200 Load Category: K
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 6,673 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 1.13 m²
Cross-sectional area of the base Ab 1.13 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 33.0 m
Pile width B 1.20 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 3.48 mm
2) Long Term Settlement 6.95 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 3.48 mm
2) Long Term Settlement 6.95 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category:2x1200 Load Category: L
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.20 m
w : 9.8 kN/m3 Pile Cut-off Level : 34.975 mRL
Pile Toe Level : 8.98 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 34.98 28.36 3.5 6.6 16 13 393 314 1
AC3 28.36 24.36 22 4.0 88 88 1,327 1,327 1
AC3 24.36 22.36 37 2.0 148 148 1,116 1,116 1
AC3 22.36 21.91 47 0.4 188 188 319 319 1
AC3 21.91 16.86 16.5 5.1 66 66 1,257 1,257 1
TS 16.86 13.36 45.5 3.5 137 137 1,801 1,801 1
TC 13.36 12.36 48 1.0 192 192 724 724 1
TC 12.36 11.36 50 1.0 200 200 754 754 1
TS 11.36 9.36 50 2.0 150 150 1,131 1,131 1
TC 9.36 8.98 48.75 0.4 195 195 286 286 1

Total 26.0 9107 9028

Ultimate Skin Friction, Qs (kN) = 9,107 9,028

B) END BEARING
Pile Depth 26.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 1.13 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 2,545

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.0 31.0 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 4,661 4,553 6,019 11,573 3,036 4,514 6,019

E) STRUCTURAL CAPACITY
Static 11,310 kN
ODE 11,310 kN
MDE 18,096 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 4,553 kN Static (kN) 2761 OK 0
ODE 6,019 kN ODE (kN) 5870 OK 2277 OK
MDE 11,573 kN MDE (kN) 7594 OK 3570 OK
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category: 2x1200 Load Category: L
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 2,761 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 1.13 m²
Cross-sectional area of the base Ab 1.13 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 26.0 m
Pile width B 1.20 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 1.13 mm
2) Long Term Settlement 2.27 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 1.13 mm
2) Long Term Settlement 2.27 mm

PILE GROUP SETTLEMENT (FLEMING ET AL.,1985)

Rs=

Rs=
Sg=Rs x Single Pile Settlement
Group Settlement Ratio Rs 1.41
Pile Group Settlement Sg 1.60 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 4x1200 Load Category: M
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.20 m
w : 9.8 kN/m3 Pile Cut-off Level : 34.975 mRL
Pile Toe Level : 3.98 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 34.98 28.36 3.5 6.6 16 13 393 314 1
AC3 28.36 24.36 22 4.0 88 88 1,327 1,327 1
AC3 24.36 22.36 37 2.0 148 148 1,116 1,116 1
AC3 22.36 21.91 47 0.4 188 188 319 319 1
AC3 21.91 16.86 16.5 5.1 66 66 1,257 1,257 1
TS 16.86 13.36 45.5 3.5 137 137 1,801 1,801 1
TC 13.36 12.36 48 1.0 192 192 724 724 1
TC 12.36 11.36 50 1.0 200 200 754 754 1
TS 11.36 9.36 50 2.0 150 150 1,131 1,131 1
TC 9.36 3.98 48.75 5.4 195 195 3,962 3,962 1

Total 31.0 12782 12704

Ultimate Skin Friction, Qs (kN) = 12,782 12,704

B) END BEARING
Pile Depth 31.0 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 1.13 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 2,545

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.0 31.0 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 6,131 6,391 8,469 15,249 4,261 6,352 8,469

E) STRUCTURAL CAPACITY
Static 11,310 kN
ODE 11,310 kN
MDE 18,096 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 6,131 kN Static (kN) 4869 OK 0
ODE 8,469 kN ODE (kN) 8397 OK 1912 OK
MDE 15,249 kN MDE (kN) 11226 OK 3480 OK
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 4x1200 Load Category: M
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 4,869 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 1.13 m²
Cross-sectional area of the base Ab 1.13 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 31.0 m
Pile width B 1.20 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 2.38 mm
2) Long Term Settlement 4.77 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 2.38 mm
2) Long Term Settlement 4.77 mm

PILE GROUP SETTLEMENT (FLEMING ET AL.,1985)

Rs=

Rs=
Sg=Rs x Single Pile Settlement
Group Settlement Ratio Rs 2.00
Pile Group Settlement Sg 4.77 mm
Project : JMRT CP101
Designed : KYKQ
PILE BEARING CAPACITY Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category :4x1200 Load Category: N
BH Ref. : 1 ABH-4 Pile Type : Bored Pile
BH Elevation : 38.4 mRL Concrete Grade, fcu : 40 N/mm2
GWT : 33.4 mRL Pile Diameter : 1.20 m
w : 9.8 kN/m3 Pile Cut-off Level : 34.975 mRL
Pile Toe Level : 2.48 mRL
A) SKIN FRICTION
SPT-N Unit Skin Friction Shaft Friction Resistance Skin Friction
Soil Type Level from Level to Shaft Length
Average (0 or 1)
Static Seismic Static Seismic
(mRL) (mRL) (m) (kN/m2) (kN/m2) (kN/m2) (kN/m2)
AC1 34.98 28.36 3.5 6.6 16 13 393 314 1
AC3 28.36 24.36 22 4.0 88 88 1,327 1,327 1
AC3 24.36 22.36 37 2.0 148 148 1,116 1,116 1
AC3 22.36 21.91 47 0.4 188 188 319 319 1
AC3 21.91 16.86 16.5 5.1 66 66 1,257 1,257 1
TS 16.86 13.36 45.5 3.5 137 137 1,801 1,801 1
TC 13.36 12.36 48 1.0 192 192 724 724 1
TC 12.36 11.36 50 1.0 200 200 754 754 1
TS 11.36 9.36 50 2.0 150 150 1,131 1,131 1
TC 9.36 2.48 48.75 6.9 195 195 5,064 5,064 1

Total 32.5 13885 13807

Ultimate Skin Friction, Qs (kN) = 13,885 13,807

B) END BEARING
Pile Depth 32.5 m Limiting End Bearing 4000 kN/m2
Soil Material at Pile Toe TC Unit End Bearing 2250 kN/m2
SPT-N Value at Pile Toe 50 Area of Toe 1.13 m²
End Bearing Multiplier 45

Ultimate End bearing, Qb (kN) = 2,545

C) NEGATIVE SKIN FRICTION (NSF)


Skin Friction
Soil Level from Level to 1 - sin =1 NSF
(0 or 1)
(mRL) (mRL) (kN/m2)
AC1 35.0 31.0 15.5 0.63 22 0 0
0
0
0
0
0

Total Negative Skin Friction (kN) = 0

D) GEOTECHNICAL CAPACITY
Factor of Compression Tension
Safety Static Static ODE MDE Static ODE MDE
Skin Friction 2.50 2.00 1.50 1.00 3.00 2.00 1.50
End Bearing 2.50 1.00
Geotechnical
Capacity (kN) 6,572 6,943 9,204 16,351 4,628 6,903 9,204

E) STRUCTURAL CAPACITY
Static 11,310 kN
ODE 11,310 kN
MDE 18,096 kN
G) WORKING LOAD
F) PILE CAPACITY Compression Capacity Check Tension Capacity Check
Static 6,572 kN Static (kN) 5219 OK 0
ODE 9,204 kN ODE (kN) 8709 OK 1803 OK
MDE 16,351 kN MDE (kN) 11299 OK 2558 OK
Project : JMRT CP101
Designed : KYKQ
PILE SETTLEMENT Checked : DAP
Date : 8-Dec-2014

Site Location : Lebak Bulus station Pile Group Category : 4x1200 Load Category: N
BH Ref. : 1 ABH-4 Pile Type : Bored Pile

PILE SETTLEMENT (TOMLINSON, 1994)

( ) 2
+2 (1 )
= +
2 4

Load in the pile shaft Ws 5,219 kN


Load in the pile base Wb 0 kN
Cross-sectional area of the shaft As 1.13 m²
Cross-sectional area of the base Ab 1.13 m²
Elastic modulus of the pile (Short Term) Ep 2.80E+07 kN/m2
Elastic modulus of the pile (Long Term) Ep 1.40E+07 kN/m2
Deformation modulus of soil beneath pile base Eb 1.00E+05 kN/m2
Shaft length L 32.5 m
Pile width B 1.20 m
Poisson’s ratio of the soil 0.3
Influence factor related to the ratio of L/B IP 0.8

A) PILE SETTLEMENT DUE TO ELASTIC SHORTENING OF THE PILE SHAFT


1) Short Term Settlement 2.68 mm
2) Long Term Settlement 5.36 mm

B) PILE SETTLEMENT DUE TO COMPRESSION OF SOIL BENEATH BASE 0.00 mm

C) TOTAL PILE SETTLEMENT AT WORKING LOAD


1) Short Term Settlement 2.68 mm
2) Long Term Settlement 5.36 mm

PILE GROUP SETTLEMENT (FLEMING ET AL.,1985)

Rs=

Rs=
Sg=Rs x Single Pile Settlement
Group Settlement Ratio Rs 2.00
Pile Group Settlement Sg 5.36 mm
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix E

Summary of Pile Settlement

TWJO-1-TCD-ST1-0004-Rev A Appendix E
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

Table 13 – Summary of Pile Settlement

TOTAL PILE PILE GROUP


PILE SETTLEMENT SETTLEMENT
COLUMN NO OF DIAMETER BOREHOLE AT WORKING AT WORKING LOAD
NO PILES REFERENCE LOAD LOAD CATEGORY

(mm) (mm) (mm)

B
PG1A 1 1000 1 ABH-4 0.2 0.0 A

C53 1 1000 1 ABH-4 0.5 0.0 B

C57 1 1000 1 ABH-4 1.3 0.0 C

C52, C54
to C56 &
1 1000 1 ABH-4 1.3 0.0 C
C58 to
C60
C25, C27,
C29 & 1 1000 1 ABH-4 2.3 0.0 D
C31

C33 1 1000 1 ABH-4 2.3 0.0 D

C1 & C35 1 1000 1 ABH-4 2.3 0.0 D

C19, C21
1 1000 1 ABH-4 2.6 0.0 E
& C23

C17 &
1 1000 1 ABH-4 3.8 0.0 F
C51

C5, C6 &
1 1000 1 ABH-4 3.8 0.0 F
C39

C8 & C13 1 1000 1 ABH-4 3.8 0.0 F

C2, C3,
C4, C36,
1 1000 1 ABH-4 3.8 0.0 F
C37 &
C38

AECOM – 2 – TCD – ST1– 0004 PAGE 40 / 51


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 Lebak Bulus Station Foundation Design

TOTAL PILE PILE GROUP


PILE SETTLEMENT SETTLEMENT
COLUMN NO OF DIAMETER BOREHOLE AT WORKING AT WORKING LOAD
NO PILES REFERENCE LOAD LOAD CATEGORY

(mm) (mm) (mm)

C7, C9 to
C12 & 1 1000 1 ABH-4 5.0 0.0 G
C14
C15, C16,
C49 & 1 1000 1 ABH-4 5.9 0.0 H
C50

C40 1 1200 1 ABH-4 2.3 0.0 I

C41, C44,
C46 & 1 1200 1 ABH-4 3.1 0.0 J
C47
C42, C43,
C45 & 1 1200 1 ABH-4 3.5 0.0 K
C48

PG2A 2 1200 1 ABH-4 1.1 1.6 L

PG2 2 1200 1 ABH-4 1.1 1.6 L

C34 4 1200 1 ABH-4 2.4 4.8 M

C18 4 1200 1 ABH-4 2.4 4.8 M

C24, C26,
C28 & 4 1200 1 ABH-4 2.4 4.8 M
C30

C32 4 1200 1 ABH-4 2.7 5.4 N

C20 &
4 1200 1 ABH-4 2.7 5.4 N
C22

AECOM – 2 – TCD – ST1– 0004 PAGE 41 / 51


TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix F

List of Relevant Drawings

TWJO-1-TCD-ST1-0004-Rev A Appendix F
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

S. no. Drawing No. Rev no. Drawing Title


1 1/STN/STR/3011 1 Pile Layout Sheet 1 of 2
2 1/STN/STR/3012 1 Pile Layout Sheet 1 of 2
3 1/STN/STR/3016 1 Pile Reinforcement Sheet 1 of 2
4 1/STN/STR/3017 1 Pile Reinforcement Sheet 1 of 2
5 1/STN/STR/3020 1 Pile Cap Reinforcement – PG1
6 1/STN/STR/3021 1 Pile Cap Reinforcement Sheet – PG4
7 1/STN/STR/3022 1 Pile Cap Reinforcement Sheet – PG1A
8 1/STN/STR/3023 1 Pile Cap Reinforcement Sheet – PG2
9 1/STN/STR/3024 1 Pile Cap Reinforcement Sheet – PG2A

TWJO-1-TCD-ST1-0004-Rev A Appendix F
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix G

List of Reference Drawings

TWJO-1-TCD-ST1-0004-Rev A Appendix G
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

S. no. Drawing No. Rev Drawing Title


no.
1 1/STN/STR/3001 1 Column Layout Sheet 1 of 2
2 1/STN/STR/3002 1 Column Layout Sheet 2 of 2
3 1/STN/STR/3003 1 Framing Plan - Concourse Level
Sheet 1 of 2
4 1/STN/STR/3004 1 Framing Plan - Concourse Level
Sheet 2 of 2
5 1/STN/STR/3005 1 Framing Plan at Track Level
6 1/STN/STR/3006 1 Framing Plan at Platform Level
7 1/STN/STR/3007 1 Longitudinal Section Sheet 1 of 3
8 1/STN/STR/3008 1 Longitudinal Section Sheet 2 of 3
9 1/STN/STR/3009 1 Longitudinal Section Sheet 3 of 3
10 1/STN/STR/3010 1 Cross Section

TWJO-1-TCD-ST1-0004-Rev A Appendix G
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix H

List of Codes & Standards

TWJO-1-TCD-ST1-0004-Rev A Appendix H
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Table 1 and Table 2 below show technical standards and specifications.

Table 1

Alternative Codes to be
No. Item Code (specified)
Used
1 Viaducts
a Train Loads ODS ODS
BD37/01, BD60/04,
b Other Loads Japanese Standards
BS6779
c Load Factors Japanese Standards BD37/01
BS5400 Part 4, Part 7
d Concrete Member Design Japanese Standards
and Part 8
e Steel Member Design Japanese Standards BS5400 Part 3 and Part 6

2 Stations
a Loadings SNI 03-1727-1989 BS6339
Load Factors and Concrete
b SNI 03-2847-2002 BS8110
Member Design
Load Factors and Steel
c SNI 03-1729-2002 BS 5950
Member design

3 Depot
a Loadings SNI 03-1727-1989 BS6339
Load Factors and Concrete
b SNI 03-2847-2002 BS8110
Member Design
Load Factors and Steel
c SNI 03-1729-2002 BS 5950
Member design

4 Seismic
a Earthquake response SNI 03-2833-2008 PTLAPI ITB report
b Earthquake response SNI 03-1726-2002 PTLAPI ITB report
Structural response and
c DSRSC-SD Eurocode 8
design of structures
d Level 1 displacement limits DSRSC-DL DSRSC-DL

5 Others
Foundations Indonesian Code BS 8004
Retaining Walls Indonesian Code BS 8002 and BS 8006

TWJO-1-TCD-ST1-0004-Rev A Appendix H
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Table 2 Alternative Code Reference and Title

Code reference Title and Description

BS5400 Steel, Concrete and Composite Bridges


Part 1 General Statement
Part 3 Design of Steel Bridges
Part 4 Design of Concrete Bridges
Part 6 Specification for Materials and Workmanship - Steel
Part 7 Specification for Materials and Workmanship – Concrete,
Reinforcement and Prestressing Tendons
Part 8 Recommendations for Materials and Workmanship –
Concrete, Reinforcement and Prestressing Tendons
Part 9 Bridge Bearings
Part 10 Fatigue

BD37/01 Design Manual for Roads and Bridges Loads for Highway Bridges (UK
Department of Transport enactment of BS5400 Part 2)

BD60/04 Design of Highway Bridges for Collision Loads

BS6779 Highway Parapets for Bridges and Other Structures

BS6399 Loading for Buildings (only where loads are not covered by SNI
documents)

BS 8110 Code of Practice for Structural Use of Concrete

BS 5950 Structural Use of Steelwork in Building

BS 8004 Code of Practice for Foundations

BS 8002 Code of Practice for Earth Retaining Structures

BS 8006 Code of Practice for Strengthened/Reinforced Soils and Other Fills

Eurocode 8 Design of structures for earthquake resistance


- Part 1 : General Rules Seismic Action and Rules for Buildings
- Part 2 : Bridges

TWJO-1-TCD-ST1-0004-Rev A Appendix H
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix I

Imposed Loading drawing

TWJO-1-TCD-ST1-0004-Rev A Appendix I
1 2 3 4 5 6 7 8 9 10 11
C
B
A
A1
2 IMPOSED DEAD LOAD ( FLOOR FINISH 100 MM THK. )
LOAD AREA
2.4 kN/m² 6128m²
THIS IMPOSED LOAD IS BASED ON:-
LEGEND LOADS AREA S.N. TITLE DRAWING REV. DATE REMARKS
NO.
2.5 kN/m² 320.70 m²
LEBAK BULUS STATION
1 CONCOURSE CP101-CP102-SK-031 R0 MAY;2012
4 kN/m² 331.90 m²
OVERALL LAYOUT
5 kN/m² 3727 m²
7.5 kN/m² 676 m² 2 CLAUSE NO-5.2(TABLE 17) OF DESIGN MANUAL
16 kN/m² 877.40 m²
NOTES:
ENDORSED BY Construction of Jakarta Mass Rapid Transit Project
PT MRT Jakarta Contract CP 101
APPROVED BY NOTICED BY NAME SIGNATURE
01 LEBAK BULUS STATION
IMPOSED LOADING
PRESIDENT DIRECTOR
VERIFIED BY SCHEDULE AT CONCOURSE LEVEL
DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/1201 - T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-SRT-1201 & 1202-A1 (IMPOSED LOADING ).DWG
12 13 14 15 16 17
C
B
A
A1
2 IMPOSED DEAD LOAD ( FLOOR FINISH 100 MM THK. )
LOAD AREA
2.4 kN/m² 6128m²
THIS IMPOSED LOAD IS BASED ON:-
LEGEND LOADS AREA S.N. TITLE DRAWING REV. DATE REMARKS
NO.
2.5 kN/m² 320.70 m² LEBAK BULUS STATION
1 CONCOURSE CP101-CP102-SK-031 R0 MAY;2012
4 kN/m² 331.90 m²
OVERALL LAYOUT
5 kN/m² 3727 m²
7.5 kN/m² 676 m² 2 CLAUSE NO-5.2(TABLE 17) OF DESIGN MANUAL
16 kN/m² 877.40 m²
NOTES:
ENDORSED BY Construction of Jakarta Mass Rapid Transit Project
PT MRT Jakarta Contract CP 101
APPROVED BY NOTICED BY NAME SIGNATURE
01 LEBAK BULUS STATION
IMPOSED LOADING
PRESIDENT DIRECTOR
VERIFIED BY SCHEDULE AT CONCOURSE LEVEL
DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/1202 A1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-SRT-1201 & 1202-A1 (IMPOSED LOADING ).DWG
1 2 3 4 5 6 7 8 9 10 11 12
C
B
A
A1
2 IMPOSED DEAD LOAD ( FLOOR FINISH 100 MM THK. ) THIS IMPOSED LOAD IS BASED ON:-
S.N. TITLE DRAWING REV. DATE REMARKS
LOAD AREA NO.
2.4 kN/m² 3518m² LEBAK BULUS STATION
1 PLATFORM CP101-CP102-SK-032 R0 MAY;2012
OVERALL LAYOUT
LEGEND LOADS AREA
4 kN/m² 41.52 m²
2 CLAUSE NO-5.2(TABLE 17) OF DESIGN MANUAL
5 kN/m² 3518.92 m²
NOTES:
ENDORSED BY Construction of Jakarta Mass Rapid Transit Project
PT MRT Jakarta Contract CP 101
APPROVED BY NOTICED BY NAME SIGNATURE
01 LEBAK BULUS STATION
IMPOSED LOADING
PRESIDENT DIRECTOR
VERIFIED BY SCHEDULE AT PLATFORM LEVEL
DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/1203 - T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-SRT-1201 & 1202-A1 (IMPOSED LOADING ).DWG
13 14 15 16 17
C
B
A
A1
2 IMPOSED DEAD LOAD ( FLOOR FINISH 100 MM THK. ) THIS IMPOSED LOAD IS BASED ON:-
S.N. TITLE DRAWING REV. DATE REMARKS
LOAD AREA NO.
2.4 kN/m² 3960m² LEBAK BULUS STATION
1 UPPER CONCOURSE CP101-CP102-SK-038 R0 MAY;2012
OVERALL LAYOUT
LEGEND LOADS AREA
4 kN/m² 41.52 m²
2 CLAUSE NO-5.2(TABLE 17) OF DESIGN MANUAL
5 kN/m² 3518.92 m²
NOTES:
ENDORSED BY Construction of Jakarta Mass Rapid Transit Project
PT MRT Jakarta Contract CP 101
APPROVED BY NOTICED BY NAME SIGNATURE
01 LEBAK BULUS STATION
IMPOSED LOADING
PRESIDENT DIRECTOR
VERIFIED BY SCHEDULE AT PLATFORM LEVEL
DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/1204 - T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-SRT-1201 & 1202-A1 (IMPOSED LOADING ).DWG
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Appendix J

Design Calculation Pile & Pile Cap

TWJO-1-TCD-ST1-0004-Rev A Appendix J
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Design of Pile

TWJO-1-TCD-ST1-0004-Rev A Appendix J
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C1 & C35


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C1 & C35

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26066 1004 1DL25004
+ 1SIDL 3780.264
+ 1CL + 1PLB +-6.134
1.1TLB - 1.1BTB
-1.789 0.013 12.851 -8.045
Min Fx 23920 1003 1DL22688
+ 1SIDL 3193.937
+ 1CL + 1PLB + 1.77
1.1TLB + 1.1BTB
1.364 -0.645 7.218 -55.406
Max Fy 23949 1005 1DL22687
+ 1SIDL 3604.581
+ 1CL + 1PLA 22.293
+ 1PLB + 1.1TLA1.779
+ 1.1TLB
-0.587
+ 1.1BTA-15.062
+ 1.1BTB -34.846
Min Fy 26095 1006 1DL25003
+ 1SIDL 3780.254
+ 1CL + 1PLA-19.433
+ 1PLB + 1.1TLA
-2.791
+ 1.1TLB0.068
- 1.1BTA -11.592
1.1BTB -28.144
Max Fz 23949 1006 1DL22687
+ 1SIDL +3716.99
1CL + 1PLA-14.068
+ 1PLB + 1.1TLA5.472
+ 1.1TLB
-0.572
- 1.1BTA --18.43
1.1BTB -7.173
Min Fz 26095 1001 1DL25003
+ 1SIDL 3206.697
+ 1CL + 1PLA +6.722
1.1TLA + -5.903
1.1BTA 0.104 -3.604 -52.206
Max Mx 26066 1001 1DL25004
+ 1SIDL 3206.697
+ 1CL + 1PLA +-1.409
1.1TLA + -1.731
1.1BTA 0.104 -16.671 -63.022
Min Mx 23920 1003 1DL22688
+ 1SIDL 3193.937
+ 1CL + 1PLB + 1.77
1.1TLB + 1.1BTB
1.364 -0.645 7.218 -55.406
Max My 26095 1004 1DL25003
+ 1SIDL 3780.264
+ 1CL + 1PLB-10.815
+ 1.1TLB - 1.1BTB
-1.574 0.013 17.932 -35.549
Min My 23949 1002 1DL22687
+ 1SIDL 3755.154
+ 1CL + 1PLA +-5.221
1.1TLA - 1.1BTA
2.246 -0.5 -23.15 -14.458
Max Mz 26070 1006 1DL25009
+ 1SIDL 3780.254
+ 1CL + 1PLA +-0.678
1PLB + 1.1TLA
-0.796
+ 1.1TLB0.068
- 1.1BTA --1.904
1.1BTB 39.105
Min Mz 26066 1005 1DL25005
+ 1SIDL 3642.964
+ 1CL + 1PLA +1.849
1PLB + 1.1TLA
-2.197
+ 1.1TLB
-0.023
+ 1.1BTA +-5.015
1.1BTB -91.402

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26066 2078 1DL25005
+ 1SIDL 4527.909
+ 0.3CL + 0.3PLB
18.681
+ 0.33TLB
100.021
- 0.33BTB
4.899
- 0.3SLX
682.892
- 0.3SLY - 147.549
1SLZ - 1.1LLB
Min Fx 23920 1015 1DL22689
+ 1SIDL +1090.22
0.3SLX + 0.3SLY
-24.277
+ 1SLZ -97.655 -4.986 -678.954 -179.784
Max Fy 23949 1152 1DL22687
+ 1SIDL 2521.942
- 1COL(-X)-MLC
351.098 10.218 -0.176 -22.356 735.325
Min Fy 26095 1086 1DL25003
+ 1SIDL 2395.627
+ 0.3CL + 0.3PLA
-200.803
+ 0.3PLB
-153.427
+ 0.33TLA -9.952
+ 0.33TLB --64.391
0.33BTA - 0.33BTB
-93.45 - 1SLX - 0.3SLY -
Max Fz 23949 3071 1DL22687
+ 1SIDL +4213.69
0.3CL + 0.3PLB
66.646
+ 0.33TLB289.74
+ 0.33BTB
3.827
+ 0.3SLX
78.237
+ 0.3SLY +20.103
1SLZ + 1.1NLB
Min Fz 26095 3047 1DL25034
+ 1SIDL 1523.737
+ 0.3CL + 0.3PLA
-64.173
+ 0.33TLA
-294.037
+ 0.33BTA
-4.792
+ 0.3SLX
-238.217
+ 0.3SLY-133.669
+ 1SLZ + 1.1NLA
Max Mx 26066 3031 1DL25004
+ 1SIDL 3643.863
+ 0.3CL + 0.3PLA
61.407
+ 0.33TLA51.378
+ 0.33BTA 10.1
+ 1SLX 287.595
+ 0.3SLY + 419.507
0.3SLZ + 1.1NLA
Min Mx 26066 3055 1DL25005
+ 1SIDL 2395.327
+ 0.3CL + 0.3PLB
-67.482
+ 0.33TLB
-57.622
+ 0.33BTB
-10.276+ 1SLX-328.26
+ 0.3SLY + 0.3SLZ
-552.24+ 1.1NLB
Max My 23923 3071 1DL22691
+ 1SIDL +4213.69
0.3CL + 0.3PLB
2.804
+ 0.33TLB 7.076
+ 0.33BTB
3.827
+ 0.3SLX
758.016
+ 0.3SLY 141.342
+ 1SLZ + 1.1NLB
Min My 26068 3047 1DL25007
+ 1SIDL 1523.737
+ 0.3CL + 0.3PLA
-10.387
+ 0.33TLA
-29.535
+ 0.33BTA
-4.792
+ 0.3SLX
-763.81
+ 0.3SLY-199.784
+ 1SLZ + 1.1NLA
Max Mz 23949 1151 1DL22687
+ 1SIDL 2631.618
+ 1COL(X)-MLC330.788 -3.992 0.619 -22.67 745.338
Min Mz 26072 1152 1DL25011
+ 1SIDL 2823.818
- 1COL(-X)-MLC0.187 -1.623 -2.491 2.498 -611.572
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26066 2378 1.15DL
25005
+ 1.2SIDL
5424.946
+ 0.42CL23.588
+ 0.42PLB 125.764
+ 0.462TLB6.155- 0.462BTB
857.208
- 0.3SLX 188.609
- 0.3SLY - 1SLZ - 1.54LLB
Min Fx 23920 2115 1.15DL
22689
+ 1.2SIDL
1104.106
+ 0.3SLX-30.122
+ 0.3SLY +-122.755
1SLZ -6.208 -851.485 -223.294
Max Fy 23949 1452 1.15DL
22687
+ 1.2SIDL
2886.489
- 1.5COL(-X)-MLC
526.525 13.202 -0.117 -25.205 1111.414
Min Fy 26095 2104 1.15DL
25034
+ 1.2SIDL
3871.623
+ 1.4CL-379.714
+ 1.4PLB + -128.809
1.54TLB - -17.676
1.54BTB -51.193 -442.403
Max Fz 23949 3171 1.15DL
22687
+ 1.2SIDL
5041.909
+ 0.42CL83.892
+ 0.42PLB 362.917
+ 0.462TLB4.795+ 0.462BTB
99.049
+ 0.3SLX 25.619
+ 0.3SLY + 1SLZ + 1.54
Min Fz 26095 3147 1.15DL
25034
+ 1.2SIDL
1636.706
+ 0.42CL-79.549
+ 0.42PLA-368.138
+ 0.462TLA +-5.950.462BTA
-300.142
+ 0.3SLX-163.984
+ 0.3SLY + 1SLZ + 1.54N
Max Mx 26066 2104 1.15DL
25004
+ 1.2SIDL
4944.488
+ 1.4CL110.849
+ 1.4PLB + 1.54TLB
39.054 - 1.54BTB
17.865 238.253 862.241
Min Mx 26066 2103 1.15DL
25005
+ 1.2SIDL
3787.832
+ 1.4CL-120.319
+ 1.4PLB + -48.588
1.54TLB + -18.002
1.54BTB -267.639 -1065.855
Max My 23923 3171 1.15DL
22691
+ 1.2SIDL
5041.909
+ 0.42CL + 0.42PLB
3.57 + 8.278
0.462TLB4.795
+ 0.462BTB
952.919
+ 0.3SLX177.849
+ 0.3SLY + 1SLZ + 1.54
Min My 26068 3147 1.15DL
25007
+ 1.2SIDL
1636.706
+ 0.42CL-12.519
+ 0.42PLA +-36.422
0.462TLA +-5.95
0.462BTA
-960.157
+ 0.3SLX-250.737
+ 0.3SLY + 1SLZ + 1.54N
Max Mz 23949 1451 1.15DL
22687
+ 1.2SIDL
3051.003
+ 1.5COL(X)-MLC
496.061 -8.113 1.076 -25.677 1126.433
Min Mz 26068 2103 1.15DL
25007
+ 1.2SIDL
3787.832
+ 1.4CL -25.116
+ 1.4PLB + -15.342
1.54TLB + -18.002
1.54BTB -312.774 -1140.706

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 3780.264 3193.937 7790.000 OK
ODE Seismic 4527.909 1090.22 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 16
nd
2 Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 1104 880.3 1045 0.842 OK
Minima 5042 102.3 1762 0.058 OK

N/M Curve for MDE


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 79.91 OK
Minima -175.6 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.378 OK 36.83 OK
Minima 3.303 OK 24.72 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 10.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26073 1004 1DL25011
+ 1SIDL 3780.264
+ 1CL + 1PLB +-0.013
1.1TLB - 1.1BTB
-1.015 0.013 1.804 14.817
Min Fx 23927 1003 1DL22695
+ 1SIDL 3193.937
+ 1CL + 1PLB +-5.554
1.1TLB + -0.864
1.1BTB -0.645 8.548 -37.938
Max Fy 26076 1006 1DL25014
+ 1SIDL 3780.254
+ 1CL + 1PLA +4.616
1PLB + 1.1TLA0.315
+ 1.1TLB0.068
- 1.1BTA --3.014
1.1BTB 26.559
Min Fy 23928 1005 1DL22696
+ 1SIDL 3604.581
+ 1CL + 1PLA +-9.042
1PLB + 1.1TLA0.495
+ 1.1TLB
-0.587
+ 1.1BTA +0.311
1.1BTB -55.54
Max Fz 26075 1001 1DL25013
+ 1SIDL 3206.697
+ 1CL + 1PLA +-5.059
1.1TLA + 1.1BTA
2.042 0.104 -11.396 -20.808
Min Fz 23930 1004 1DL22698
+ 1SIDL 3258.799
+ 1CL + 1PLB + 1.074
1.1TLB - -1.129
1.1BTB -0.45 5.992 7.534
Max Mx 26073 1001 1DL25011
+ 1SIDL 3206.697
+ 1CL + 1PLA +-5.892
1.1TLA + 1.1BTA
1.82 0.104 -15.227 -32.269
Min Mx 23927 1003 1DL22695
+ 1SIDL 3193.937
+ 1CL + 1PLB +-5.554
1.1TLB + -0.864
1.1BTB -0.645 8.548 -37.938
Max My 23927 1004 1DL22695
+ 1SIDL 3258.799
+ 1CL + 1PLB + 0.22
1.1TLB - 1.1BTB
-0.849 -0.45 9.011 9.341
Min My 26073 1001 1DL25011
+ 1SIDL 3206.697
+ 1CL + 1PLA +-5.892
1.1TLA + 1.1BTA
1.82 0.104 -15.227 -32.269
Max Mz 26073 1006 1DL25011
+ 1SIDL 3780.254
+ 1CL + 1PLA +2.815
1PLB + 1.1TLA
-0.195
+ 1.1TLB0.068
- 1.1BTA --3.072
1.1BTB 37.714
Min Mz 23927 1005 1DL22695
+ 1SIDL 3604.581
+ 1CL + 1PLA + -8.56
1PLB + 1.1TLA0.734
+ 1.1TLB
-0.587
+ 1.1BTA +-0.422
1.1BTB -64.1
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26073 2078 1DL25012
+ 1SIDL 4527.909
+ 0.3CL + 0.3PLB
14.74
+ 0.33TLB67.231
- 0.33BTB
4.899
- 0.3SLX
578.976
- 0.3SLY - 133.233
1SLZ - 1.1LLB
Min Fx 23927 1015 1DL22696
+ 1SIDL +1090.22
0.3SLX + 0.3SLY
-17.733
+ 1SLZ -67.253 -4.986 -573.293 -136.152
Max Fy 26075 1086 1DL25014
+ 1SIDL 3833.578
+ 0.3CL + 0.3PLA
60.713
+ 0.3PLB42.106
+ 0.33TLA +9.851
0.33TLB 210.127
- 0.33BTA - 0.33BTB
301.797 - 1SLX - 0.3SLY -
Min Fy 26077 1152 1DL25015
+ 1SIDL 2823.818
- 1COL(-X)-MLC-73.43 -0.286 -2.491 -0.867 -381.762
Max Fz 26075 3047 1DL25013
+ 1SIDL 4326.038
+ 0.3CL + 0.3PLA
16.406
+ 0.33TLA84.833
+ 0.33BTA5.189
+ 0.3SLX
491.724
+ 0.3SLY106.721
+ 1SLZ + 1.1NLA
Min Fz 23929 3071 1DL22698
+ 1SIDL 1260.235
+ 0.3CL + 0.3PLB
-21.163
+ 0.33TLB
-84.108
+ 0.33BTB
-5.288
+ 0.3SLX
-409.541
+ 0.3SLY-101.956
+ 1SLZ + 1.1NLB
Max Mx 26073 3031 1DL25011
+ 1SIDL 3643.863
+ 0.3CL + 0.3PLA
48.072
+ 0.33TLA34.958
+ 0.33BTA 10.1
+ 1SLX 312.165
+ 0.3SLY + 449.634
0.3SLZ + 1.1NLA
Min Mx 26073 3055 1DL25012
+ 1SIDL 2395.327
+ 0.3CL + 0.3PLB
-54.727
+ 0.33TLB
-34.762
+ 0.33BTB
-10.276+ 1SLX
-297.362
+ 0.3SLY +-421.397
0.3SLZ + 1.1NLB
Max My 23927 3071 1DL22695
+ 1SIDL +4213.69
0.3CL + 0.3PLB
12.704
+ 0.33TLB66.908
+ 0.33BTB
3.827
+ 0.3SLX
659.493
+ 0.3SLY 127.896
+ 1SLZ + 1.1NLB
Min My 26073 3078 1DL25011
+ 1SIDL 1695.803
+ 0.3CL + 0.3PLB
-17.821
+ 0.33TLB-67.46
- 0.33BTB
-4.82
- 0.3SLX
-661.312
- 0.3SLY --143.054
1SLZ - 1.1NLB
Max Mz 26073 1007 1DL25011
+ 1SIDL 3548.299
+ 1SLX + 0.3SLY
49.116
+ 0.3SLZ 33.801 9.801 319.816 457.462
Min Mz 26073 1152 1DL25011
+ 1SIDL 2823.818
- 1COL(-X)-MLC
-33.569 -1.267 -2.491 2.498 -611.572

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26073 2378 1.15DL
25012
+ 1.2SIDL
5424.946
+ 0.42CL18.827
+ 0.42PLB +84.299
0.462TLB6.155
- 0.462BTB
728.088
- 0.3SLX 167.964
- 0.3SLY - 1SLZ - 1.54LLB
Min Fx 23927 2115 1.15DL
22696
+ 1.2SIDL
1104.106
+ 0.3SLX-22.043
+ 0.3SLY + 1SLZ
-84.437 -6.208 -720.309 -170.164
Max Fy 26075 2104 1.15DL
25013
+ 1.2SIDL
4944.488
+ 1.4CL118.237
+ 1.4PLB + 1.54TLB
35.512 - 1.54BTB
17.865 202.657 695.561
Min Fy 26075 2103 1.15DL
25014
+ 1.2SIDL
3787.832
+ 1.4CL-122.601
+ 1.4PLB + 1.54TLB
-33.99 + -18.002
1.54BTB -186.475 -580.153
Max Fz 26075 3147 1.15DL
25013
+ 1.2SIDL
5142.326
+ 0.42CL20.568
+ 0.42PLA 106.563
+ 0.462TLA 6.561
+ 0.462BTA
617.096
+ 0.3SLX132.943
+ 0.3SLY + 1SLZ + 1.54N
Min Fz 23929 3171 1.15DL
22698
+ 1.2SIDL
1342.127
+ 0.42CL -26.59
+ 0.42PLB-105.664
+ 0.462TLB -6.631
+ 0.462BTB
-514.098
+ 0.3SLX
-128.257
+ 0.3SLY + 1SLZ + 1.54
Max Mx 26073 2104 1.15DL
25011
+ 1.2SIDL
4944.488
+ 1.4CL +98.821
1.4PLB + 1.54TLB
27.107 - 1.54BTB
17.865 262.747 907.998
Min Mx 26073 2103 1.15DL
25012
+ 1.2SIDL
3787.832
+ 1.4CL-105.906
+ 1.4PLB + -27.751
1.54TLB + -18.002
1.54BTB -254.897 -822.043
Max My 23927 3171 1.15DL
22695
+ 1.2SIDL
5041.909
+ 0.42CL16.003
+ 0.42PLB +83.797
0.462TLB4.795
+ 0.462BTB
827.764
+ 0.3SLX160.138
+ 0.3SLY + 1SLZ + 1.54
Min My 26073 3178 1.15DL
25011
+ 1.2SIDL
1877.598
+ 0.42CL-22.025
+ 0.42PLB +-84.596
0.462TLB
-5.988
- 0.462BTB
-829.131
- 0.3SLX-178.143
- 0.3SLY - 1SLZ - 1.54NL
Max Mz 26073 2104 1.15DL
25011
+ 1.2SIDL
4944.488
+ 1.4CL +98.821
1.4PLB + 1.54TLB
27.107 - 1.54BTB
17.865 262.747 907.998
Min Mz 26073 1452 1.15DL
25011
+ 1.2SIDL
3247.468
- 1.5COL(-X)-MLC
-49.572 -1.886 -3.699 7.023 -915.928

ODE MDE
Maximum Tension Force (kN) 1090.22 1104.106
Skin Friction (kN) 1722.67
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 1104 740.1 885.8 0.836 OK
Minima 5142 631.3 1658 0.381 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 73.38 OK
Minima -127.5 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.113 OK 35.56 OK
Minima 3.581 OK 26.25 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.7645 m
Hence de = 0.743 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 527 kN
Corresponding axial compressive force, N = 2886 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 4536 mm2
Effective area of tensile steel = 50% of total steel = As = 0.0023 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.339 %
Horizontal shear force, Vu = 527 kN
Shear stress (vv = Vu /(bv . dv) = 787.26 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.515 Mpa
= 515 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 478.933 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/Ac) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.18
Modified shear strength of concrete (n s vc ) = 566.94 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 147.40 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.61 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C2, C3, C4, C36, C37 & C38
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C2, C3, C4, C36, C37 & C38

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26099 1003 1DL25037
+ 1SIDL 5179.702
+ 1CL + 1PLB + 6.187
1.1TLB + -10.173
1.1BTB -0.519 26.283 -50.148
Min Fx 23986 1004 1DL22754
+ 1SIDL 4188.322
+ 1CL + 1PLB + 1.457
1.1TLB - 1.1BTB
5.945 -0.295 -2.882 5.694
Max Fy 24015 1005 1DL22753
+ 1SIDL 4938.095
+ 1CL + 1PLA +33.616
1PLB + 1.1TLA
14.538
+ 1.1TLB-0.31
+ 1.1BTA-63.843
+ 1.1BTB 5.136
Min Fy 24048 1006 1DL22786
+ 1SIDL +5070.26
1CL + 1PLA -20.736
+ 1PLB + 1.1TLA
14.386
+ 1.1TLB
-0.498
- 1.1BTA - -54.11
1.1BTB -32.961
Max Fz 23982 1006 1DL22720
+ 1SIDL 4972.904
+ 1CL + 1PLA -14.953
+ 1PLB + 1.1TLA
18.375
+ 1.1TLB
-0.334
- 1.1BTA -66.173
- 1.1BTB -10.835
Min Fz 26161 1005 1DL25069
+ 1SIDL 5038.289
+ 1CL + 1PLA +33.556
1PLB + 1.1TLA
-19.904
+ 1.1TLB-0.39
+ 1.1BTA +60.767
1.1BTB 2.99
Max Mx 23953 1001 1DL22721
+ 1SIDL 5047.399
+ 1CL + 1PLA + 5.624
1.1TLA + 1.1BTA
9.469 -0.06 -37.011 -50.478
Min Mx 26099 1003 1DL25037
+ 1SIDL 5179.702
+ 1CL + 1PLB + 6.187
1.1TLB + -10.173
1.1BTB -0.519 26.283 -50.148
Max My 26128 1004 1DL25036
+ 1SIDL 5167.435
+ 1CL + 1PLB +-2.892
1.1TLB - -15.939
1.1BTB -0.264 68.954 -7.5
Min My 23982 1001 1DL22720
+ 1SIDL 5047.399
+ 1CL + 1PLA +18.622
1.1TLA + 12.997
1.1BTA -0.06 -72.585 -9.057
Max Mz 24023 1006 1DL22792
+ 1SIDL +5070.26
1CL + 1PLA +-0.994
1PLB + 1.1TLA
3.581
+ 1.1TLB
-0.498
- 1.1BTA -12.593
1.1BTB 40.287
Min Mz 26134 1005 1DL25073
+ 1SIDL 5038.289
+ 1CL + 1PLA + 2.443
1PLB + 1.1TLA
-6.653
+ 1.1TLB-0.39
+ 1.1BTA-15.707
+ 1.1BTB -93.678

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26132 2078 1DL25071
+ 1SIDL 5537.744
+ 0.3CL + 0.3PLB
25.096
+ 0.33TLB 97.211
- 0.33BTB
4.606
- 0.3SLX
692.007
- 0.3SLY - 1SLZ
143.688
- 1.1LLB
Min Fx 23986 1015 1DL22755
+ 1SIDL 1800.855
+ 0.3SLX + 0.3SLY
-18.977
+ 1SLZ -96.299 -4.912 -688.281 -172.14
Max Fy 26128 1152 1DL25036
+ 1SIDL 3654.948
- 1COL(-X)-MLC
364.927 -20.127 -1.901 82.196 776.739
Min Fy 26128 1086 1DL25036
+ 1SIDL 3470.497
+ 0.3CL + 0.3PLA
-215.294
+ 0.3PLB
-163.496
+ 0.33TLA +-9.843
0.33TLB --55.216
0.33BTA - 0.33BTB
-82.521- 1SLX - 0.3SLY
Max Fz 24015 3054 1DL22784
+ 1SIDL 5181.365
+ 0.3CL + 0.3PLA
68.861
+ 0.33TLA
304.087
- 0.33BTA4.146
- 0.3SLX243.057
- 0.3SLY - 1SLZ
54.773
- 1.1NLA
Min Fz 26161 3078 1DL25069
+ 1SIDL 2526.001
+ 0.3CL + 0.3PLB
-57.995
+ 0.33TLB
-310.933
- 0.33BTB
-4.95
- 0.3SLX-99.287
- 0.3SLY - 1SLZ
-12.302
- 1.1NLB
Max Mx 26099 3031 1DL25037
+ 1SIDL 4513.306
+ 0.3CL + 0.3PLA
81.87
+ 0.33TLA43.51
+ 0.33BTA9.58
+ 1SLX325.937
+ 0.3SLY + 399.374
0.3SLZ + 1.1NLA
Min Mx 26099 3055 1DL25038
+ 1SIDL +3492.77
0.3CL + 0.3PLB
-74.628
+ 0.33TLB -67.2
+ 0.33BTB
-10.175+ 1SLX
-326.083
+ 0.3SLY + -532.731
0.3SLZ + 1.1NLB
Max My 23956 3071 1DL22724
+ 1SIDL 4468.256
+ 0.3CL + 0.3PLB
0.629
+ 0.33TLB 23.38
+ 0.33BTB
4.074
+ 0.3SLX
747.604
+ 0.3SLY +140.251
1SLZ + 1.1NLB
Min My 26101 3047 1DL25040
+ 1SIDL 2934.474
+ 0.3CL + 0.3PLA
-6.969
+ 0.33TLA-33.168
+ 0.33BTA
-4.885
+ 0.3SLX
-755.738
+ 0.3SLY +-208.65
1SLZ + 1.1NLA
Max Mz 26128 1152 1DL25036
+ 1SIDL 3654.948
- 1COL(-X)-MLC
364.927 -20.127 -1.901 82.196 776.739
Min Mz 26105 1152 1DL25044
+ 1SIDL 3654.948
- 1COL(-X)-MLC2.343 -3.652 -1.901 -22.597 -631.172
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26099 2103 1.15DL
25037
+ 1.2SIDL
6640.337
+ 1.4CL156.204
+ 1.4PLB + 1.54TLB
19.34 + 16.656
1.54BTB 222.084 748.88
Min Fx 23986 2115 1.15DL
22755
+ 1.2SIDL
1935.289
+ 0.3SLX-24.122
+ 0.3SLY +-121.031
1SLZ -6.135 -861.18 -214.303
Max Fy 26128 1452 1.15DL
25036
+ 1.2SIDL
4208.242
- 1.5COL(-X)-MLC
544.816 -21.902 -2.747 94.391 1165.396
Min Fy 26128 2104 1.15DL
25067
+ 1.2SIDL
5859.58
+ 1.4CL-418.922
+ 1.4PLB + -109.069
1.54TLB - -17.342
1.54BTB -39.064 -286.088
Max Fz 24015 3154 1.15DL
22784
+ 1.2SIDL
6227.807
+ 0.42CL85.341
+ 0.42PLA 378.754
+ 0.462TLA -5.201
0.462BTA
304.721
- 0.3SLX - 69.747
0.3SLY - 1SLZ - 1.54N
Min Fz 26161 3178 1.15DL
25069
+ 1.2SIDL
2881.861
+ 0.42CL-73.993
+ 0.42PLB-386.508
+ 0.462TLB-6.152
- 0.462BTB
-122.979
- 0.3SLX --14.832
0.3SLY - 1SLZ - 1.54N
Max Mx 26132 2104 1.15DL
25070
+ 1.2SIDL
6430.407
+ 1.4CL138.456
+ 1.4PLB + 1.54TLB
13.428 - 1.54BTB
17.052 183.217 843.415
Min Mx 26132 2103 1.15DL
25071
+ 1.2SIDL
5730.677
+ 1.4CL-127.043
+ 1.4PLB + 1.54TLB
-41.943 + -17.701
1.54BTB -177.173 -1042.279
Max My 23956 3171 1.15DL
22724
+ 1.2SIDL
5298.761
+ 0.42CL +0.725
0.42PLB +27.682
0.462TLB5.091
+ 0.462BTB
938.681
+ 0.3SLX176.783
+ 0.3SLY + 1SLZ + 1.5
Min My 26101 3147 1.15DL
25040
+ 1.2SIDL
3354.036
+ 0.42CL -8.678
+ 0.42PLA +-39.482
0.462TLA +-6.05
0.462BTA
-948.528
+ 0.3SLX-261.464
+ 0.3SLY + 1SLZ + 1.5
Max Mz 26128 1452 1.15DL
25036
+ 1.2SIDL
4208.242
- 1.5COL(-X)-MLC
544.816 -21.902 -2.747 94.391 1165.396
Min Mz 26101 2103 1.15DL
25040
+ 1.2SIDL
5876.753
+ 1.4CL -37.564
+ 1.4PLB + 1.54TLB
-13.384 + -17.699
1.54BTB -263.884 -1166.537

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 5179.702 4188.322 7790.000 OK
ODE Seismic 5537.744 1800.855 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 16 16
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 1935 887.4 1117 0.795 OK
Minima 2882 123.9 1339 0.093 OK

N/M Curve for MDE


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 87.01 OK
Minima -85.64 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 7.2 OK 49.79 OK
Minima 5.138 OK 36.81 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.766 m
Hence de = 0.744 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 545 kN
Corresponding axial compressive force, N = 4208 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 3217 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0016 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.240 %
Horizontal shear force, Vu = 545 kN
Shear stress (vv = Vu /(bv . dv) = 814.49 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.459 Mpa
= 459 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 426.930 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.27
Modified shear strength of concrete (n s vc ) = 541.31 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 182.88 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.78 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C5, C6 & C39


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C5, C6 & C39

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24085 1005 1DL22853
+ 1SIDL +5046.94
1CL + 1PLA +4.428
1PLB + 1.1TLA
16.89
+ 1.1TLB
-0.232
+ 1.1BTA-42.082
+ 1.1BTB -86.254
Min Fx 26198 1001 1DL25136
+ 1SIDL 3884.959
+ 1CL + 1PLA +12.247
1.1TLA + -8.116
1.1BTA -0.186 -6.764 -40.341
Max Fy 24081 1005 1DL22819
+ 1SIDL 4691.158
+ 1CL + 1PLA 41.485
+ 1PLB + 1.1TLA
16.232
+ 1.1TLB
-0.102
+ 1.1BTA-73.097
+ 1.1BTB 32.054
Min Fy 24114 1006 1DL22852
+ 1SIDL 4597.792
+ 1CL + 1PLA-15.859
+ 1PLB + 1.1TLA
17.355
+ 1.1TLB
-0.192
- 1.1BTA-67.197
- 1.1BTB -17.874
Max Fz 24114 1005 1DL22852
+ 1SIDL +5046.94
1CL + 1PLA +21.661
1PLB + 1.1TLA
26.784
+ 1.1TLB
-0.232
+ 1.1BTA
-112.241
+ 1.1BTB -40.615
Min Fz 26227 1005 1DL25135
+ 1SIDL 4598.165
+ 1CL + 1PLA +41.148
1PLB + 1.1TLA
-21.815
+ 1.1TLB
-0.446
+ 1.1BTA 64.559
+ 1.1BTB 29.672
Max Mx 24052 1001 1DL22820
+ 1SIDL 4763.942
+ 1CL + 1PLA +12.833
1.1TLA + 10.466
1.1BTA 0.09 -39.687 -39.395
Min Mx 26198 1003 1DL25136
+ 1SIDL 4680.227
+ 1CL + 1PLB +12.511
1.1TLB +-11.212
1.1BTB -0.535 23.062 -39.979
Max My 26227 1004 1DL25135
+ 1SIDL 4685.487
+ 1CL + 1PLB + 9.818
1.1TLB - -17.577
1.1BTB -0.347 71.073 36.671
Min My 24114 1005 1DL22852
+ 1SIDL +5046.94
1CL + 1PLA +21.661
1PLB + 1.1TLA
26.784
+ 1.1TLB
-0.232
+ 1.1BTA
-112.241
+ 1.1BTB -40.615
Max Mz 24081 1006 1DL22850
+ 1SIDL 4659.811
+ 1CL + 1PLA + -0.07
1PLB + 1.1TLA
18.57
+ 1.1TLB
-0.148
- 1.1BTA-51.757
- 1.1BTB 40.6
Min Mz 26201 1005 1DL25140
+ 1SIDL 4598.165
+ 1CL + 1PLA +1.537
1PLB + 1.1TLA
-5.289
+ 1.1TLB
-0.446
+ 1.1BTA-23.885
+ 1.1BTB -98.841

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24085 1079 1DL22853
+ 1SIDL 6277.708
+ 0.3CL + 0.3PLA
57.662
+ 0.3PLB77.641
+ 0.33TLA +7.828
0.33TLB 227.179
+ 0.33BTA +394.695
0.33BTB + 1SLX + 0.3SLY
Min Fx 24085 1007 1DL22854
+ 1SIDL 1477.007
+ 1SLX + 0.3SLY
-55.698
+ 0.3SLZ -56.585 -8.138 -263.801 -511.469
Max Fy 26227 1152 1DL25135
+ 1SIDL 3430.635
- 1COL(-X)-MLC
363.961 -16.817 -2.181 53.298 772.697
Min Fy 26227 1086 1DL25135
+ 1SIDL 3224.622
+ 0.3CL + 0.3PLA
-197.545
+ 0.3PLB-133.46
+ 0.33TLA -9.028
+ 0.33TLB --45.267
0.33BTA - 0.33BTB
-27.828 - 1SLX - 0.3SLY -
Max Fz 24081 3054 1DL22850
+ 1SIDL 5198.111
+ 0.3CL + 0.3PLA
74.29
+ 0.33TLA
295.474
- 0.33BTA4.465
- 0.3SLX235.789
- 0.3SLY - 1SLZ
65.296
- 1.1NLA
Min Fz 26227 3078 1DL25135
+ 1SIDL 2531.127
+ 0.3CL + 0.3PLB
-54.516
+ 0.33TLB
-295.968
- 0.33BTB
-5.007
- 0.3SLX
-77.211
- 0.3SLY - 1SLZ
-9.565
- 1.1NLB
Max Mx 26198 3031 1DL25136
+ 1SIDL 4148.448
+ 0.3CL + 0.3PLA
79.842
+ 0.33TLA36.738
+ 0.33BTA8.536
+ 1SLX240.98
+ 0.3SLY + 414.891
0.3SLZ + 1.1NLA
Min Mx 26198 3055 1DL25137
+ 1SIDL 3250.789
+ 0.3CL + 0.3PLB
-65.193
+ 0.33TLB
-55.531
+ 0.33BTB
-9.178+ 1SLX
-253.505
+ 0.3SLY +-533.843
0.3SLZ + 1.1NLB
Max My 24055 3071 1DL22823
+ 1SIDL 4955.986
+ 0.3CL + 0.3PLB
2.658
+ 0.33TLB16.949
+ 0.33BTB
4.414+ 0.3SLX
719.068
+ 0.3SLY 135.402
+ 1SLZ + 1.1NLB
Min My 26200 3047 1DL25139
+ 1SIDL 2290.964
+ 0.3CL + 0.3PLA
-4.052
+ 0.33TLA
-35.194
+ 0.33BTA
-4.958
+ 0.3SLX
-730.819
+ 0.3SLY-209.473
+ 1SLZ + 1.1NLA
Max Mz 24081 1151 1DL22819
+ 1SIDL 3560.855
+ 1COL(X)-MLC339.476 6.608 0.283 -68.204 777.723
Min Mz 26204 1152 1DL25143
+ 1SIDL 3430.635
- 1COL(-X)-MLC2.159 -1.674 -2.181 -23.655 -630.117
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24085 2103 1.15DL
22853
+ 1.2SIDL
8850.322
+ 1.4CL106.008
+ 1.4PLB + 1.54TLB
75.69 + 13.867
1.54BTB 99.049 751.686
Min Fx 24085 2104 1.15DL
22854
+ 1.2SIDL
1198.575
+ 1.4CL-110.997
+ 1.4PLB + -58.717
1.54TLB - -14.171
1.54BTB -95.127 -932.803
Max Fy 26227 1452 1.15DL
25135
+ 1.2SIDL
3939.893
- 1.5COL(-X)-MLC
541.69 -19.388 -3.165 61.085 1153.722
Min Fy 26227 2104 1.15DL
25166
+ 1.2SIDL
5325.333
+ 1.4CL-381.463
+ 1.4PLB + -72.313
1.54TLB - -15.696
1.54BTB 35.585 -294.571
Max Fz 24081 3154 1.15DL
22850
+ 1.2SIDL
6205.272
+ 0.42CL91.995
+ 0.42PLA 368.228
+ 0.462TLA 5.607
- 0.462BTA
294.788
- 0.3SLX -82.635
0.3SLY - 1SLZ - 1.54NLA
Min Fz 26227 3178 1.15DL
25135
+ 1.2SIDL
2879.695
+ 0.42CL-69.637
+ 0.42PLB-368.822
+ 0.462TLB -6.243
- 0.462BTB
-95.866
- 0.3SLX --11.197
0.3SLY - 1SLZ - 1.54NL
Max Mx 26198 2104 1.15DL
25136
+ 1.2SIDL
5697.907
+ 1.4CL142.981
+ 1.4PLB + 1.54TLB
0.101 - 1.54BTB
15.129 117.868 849.438
Min Mx 26198 2103 1.15DL
25137
+ 1.2SIDL
5317.97
+ 1.4CL-120.105
+ 1.4PLB + -32.416
1.54TLB + -15.958
1.54BTB -99.627 -1034.859
Max My 24055 3171 1.15DL
22823
+ 1.2SIDL
5866.297
+ 0.42CL +3.249
0.42PLB +19.893
0.462TLB5.535
+ 0.462BTB
903.138
+ 0.3SLX170.917
+ 0.3SLY + 1SLZ + 1.54
Min My 26200 3147 1.15DL
25139
+ 1.2SIDL
2543.467
+ 0.42CL -5.064
+ 0.42PLA +-42.901
0.462TLA-6.175
+ 0.462BTA
-917.281
+ 0.3SLX-262.314
+ 0.3SLY + 1SLZ + 1.54N
Max Mz 24081 1451 1.15DL
22819
+ 1.2SIDL
4134.997
+ 1.5COL(X)-MLC
505.185 4.746 0.467 -81.409 1161.708
Min Mz 26200 2103 1.15DL
25139
+ 1.2SIDL
5317.97
+ 1.4CL -24.981
+ 1.4PLB + 1.54TLB
-14.45 + -15.958
1.54BTB -136.457 -1160.314

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 5046.94 3884.959 7790.000 OK
ODE Seismic 6277.708 1477.007 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 16
nd
2 Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 1199 937.6 1071 0.876 OK
Minima 2880 96.52 1470 0.066 OK

N/M Curve for MDE


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 82.2 OK
Minima -55.56 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 7.377 OK 50.63 OK
Minima 4.376 OK 31.96 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 10.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24092 1005 1DL22860
+ 1SIDL +5046.94
1CL + 1PLA +-8.854
1PLB + 1.1TLA1.953
+ 1.1TLB
-0.232
+ 1.1BTA 29.183
+ 1.1BTB -64.381
Min Fx 26205 1001 1DL25143
+ 1SIDL 3884.959
+ 1CL + 1PLA +-5.405
1.1TLA + 1.1BTA
1.66 -0.186 -29.76 -62.477
Max Fy 24095 1006 1DL22863
+ 1SIDL 4597.792
+ 1CL + 1PLA +4.002
1PLB + 1.1TLA
-2.183
+ 1.1TLB
-0.192
- 1.1BTA -19.263
1.1BTB 22.215
Min Fy 26208 1005 1DL25146
+ 1SIDL 4598.165
+ 1CL + 1PLA-11.155
+ 1PLB + 1.1TLA3.662
+ 1.1TLB
-0.446
+ 1.1BTA-26.322
+ 1.1BTB -59.408
Max Fz 26209 1005 1DL25147
+ 1SIDL 4598.165
+ 1CL + 1PLA-10.661
+ 1PLB + 1.1TLA 3.87
+ 1.1TLB
-0.446
+ 1.1BTA-22.661
+ 1.1BTB -48.252
Min Fz 24098 1005 1DL22866
+ 1SIDL +5046.94
1CL + 1PLA +-5.885
1PLB + 1.1TLA
-3.794
+ 1.1TLB
-0.232
+ 1.1BTA 18.515
+ 1.1BTB -14.326
Max Mx 24059 1001 1DL22827
+ 1SIDL 4763.942
+ 1CL + 1PLA +-5.387
1.1TLA + 1.1BTA
2.521 0.09 10.145 -63.788
Min Mx 26205 1003 1DL25143
+ 1SIDL 4680.227
+ 1CL + 1PLB +-5.403
1.1TLB + -0.827
1.1BTB -0.535 -22.214 -63.107
Max My 24092 1005 1DL22861
+ 1SIDL +5046.94
1CL + 1PLA +-8.854
1PLB + 1.1TLA1.953
+ 1.1TLB
-0.232
+ 1.1BTA 31.136
+ 1.1BTB -55.527
Min My 26205 1005 1DL25143
+ 1SIDL 4598.165
+ 1CL + 1PLA +-8.336
1PLB + 1.1TLA0.542
+ 1.1TLB
-0.446
+ 1.1BTA-32.105
+ 1.1BTB -89.143
Max Mz 24092 1006 1DL22860
+ 1SIDL 4597.792
+ 1CL + 1PLA +2.702
1PLB + 1.1TLA0.826
+ 1.1TLB
-0.192
- 1.1BTA -20.626
1.1BTB 32.359
Min Mz 24059 1005 1DL22827
+ 1SIDL 4691.158
+ 1CL + 1PLA +-8.235
1PLB + 1.1TLA1.587
+ 1.1TLB
-0.102
+ 1.1BTA 16.111
+ 1.1BTB -89.209
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24092 1079 1DL22860
+ 1SIDL 6277.708
+ 0.3CL + 0.3PLA
44.394
+ 0.3PLB25.633
+ 0.33TLA +7.828
0.33TLB 286.163
+ 0.33BTA +398.245
0.33BTB + 1SLX + 0.3SLY
Min Fx 24092 1007 1DL22861
+ 1SIDL 1477.007
+ 1SLX + 0.3SLY
-50.735
+ 0.3SLZ -23.377 -8.138 -229.761 -391.154
Max Fy 26207 1086 1DL25146
+ 1SIDL 4373.487
+ 0.3CL + 0.3PLA
60.116
+ 0.3PLB32.631
+ 0.33TLA +8.379
0.33TLB 146.084
- 0.33BTA - 0.33BTB
297.718 - 1SLX - 0.3SLY -
Min Fy 26209 1152 1DL25147
+ 1SIDL 3430.635
- 1COL(-X)-MLC
-75.673 2.854 -2.181 -17.258 -396.278
Max Fz 26207 3047 1DL25145
+ 1SIDL 4857.066
+ 0.3CL + 0.3PLA
14.789
+ 0.33TLA81.779
+ 0.33BTA4.623
+ 0.3SLX
461.961
+ 0.3SLY +87.675
1SLZ + 1.1NLA
Min Fz 24062 3071 1DL22831
+ 1SIDL 2224.244
+ 0.3CL + 0.3PLB
-22.875
+ 0.33TLB
-80.633
+ 0.33BTB
-4.948
+ 0.3SLX
-315.557
+ 0.3SLY +-95.693
1SLZ + 1.1NLB
Max Mx 26205 3031 1DL25143
+ 1SIDL 4148.448
+ 0.3CL + 0.3PLA
47.544
+ 0.33TLA26.781
+ 0.33BTA8.536
+ 1SLX 218.771
+ 0.3SLY + 442.474
0.3SLZ + 1.1NLA
Min Mx 26205 3055 1DL25144
+ 1SIDL 3250.789
+ 0.3CL + 0.3PLB
-53.515
+ 0.33TLB
-26.448
+ 0.33BTB
-9.178
+ 1SLX-244.69
+ 0.3SLY +-461.335
0.3SLZ + 1.1NLB
Max My 24059 3071 1DL22827
+ 1SIDL 4955.986
+ 0.3CL + 0.3PLB
12.558
+ 0.33TLB65.833
+ 0.33BTB
4.414
+ 0.3SLX
643.237
+ 0.3SLY 111.723
+ 1SLZ + 1.1NLB
Min My 26205 3078 1DL25143
+ 1SIDL 2531.127
+ 0.3CL + 0.3PLB
-17.112
+ 0.33TLB
-65.182
- 0.33BTB
-5.007
- 0.3SLX
-648.015
- 0.3SLY --169.911
1SLZ - 1.1NLB
Max Mz 26205 1007 1DL25143
+ 1SIDL 4024.208
+ 1SLX + 0.3SLY
48.554
+ 0.3SLZ 25.952 8.399 224.044 453.665
Min Mz 26205 1152 1DL25143
+ 1SIDL 3430.635
- 1COL(-X)-MLC
-33.218 0.138 -2.181 -23.655 -630.117

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24092 2103 1.15DL
22860
+ 1.2SIDL
8850.322
+ 1.4CL +85.201
1.4PLB + 1.54TLB
9.272 + 13.867
1.54BTB 180.932 766.963
Min Fx 24092 2104 1.15DL
22861
+ 1.2SIDL
1198.575
+ 1.4CL -92.551
+ 1.4PLB + 1.54TLB
-7.738 - -14.171
1.54BTB -146.895 -706.817
Max Fy 26207 2104 1.15DL
25145
+ 1.2SIDL
5697.907
+ 1.4CL117.774
+ 1.4PLB + 1.54TLB
16.308 - 1.54BTB
15.129 46.455 695.925
Min Fy 26207 2103 1.15DL
25146
+ 1.2SIDL
5317.97
+ 1.4CL-128.337
+ 1.4PLB + 1.54TLB
-9.943 + -15.958
1.54BTB -100.379 -644.711
Max Fz 26207 3147 1.15DL
25145
+ 1.2SIDL
5741.611
+ 0.42CL18.687
+ 0.42PLA +102.51
0.462TLA 5.859
+ 0.462BTA
580.561
+ 0.3SLX110.729
+ 0.3SLY + 1SLZ + 1.54N
Min Fz 24061 3171 1.15DL
22830
+ 1.2SIDL
2463.544
+ 0.42CL-28.876
+ 0.42PLB-101.044
+ 0.462TLB -6.223
+ 0.462BTB
-492.068
+ 0.3SLX
-148.361
+ 0.3SLY + 1SLZ + 1.54
Max Mx 26205 2104 1.15DL
25143
+ 1.2SIDL
5697.907
+ 1.4CL +97.842
1.4PLB + 1.54TLB
10.147 - 1.54BTB
15.129 68.893 906.728
Min Mx 26205 2103 1.15DL
25144
+ 1.2SIDL
5317.97
+ 1.4CL-103.882
+ 1.4PLB + -11.001
1.54TLB + -15.958
1.54BTB -131.694 -894.986
Max My 24059 3171 1.15DL
22827
+ 1.2SIDL
5866.297
+ 0.42CL15.834
+ 0.42PLB +82.325
0.462TLB5.535
+ 0.462BTB
804.964
+ 0.3SLX 141.14
+ 0.3SLY + 1SLZ + 1.54
Min My 26205 3178 1.15DL
25143
+ 1.2SIDL
2879.695
+ 0.42CL-21.169
+ 0.42PLB +-81.716
0.462TLB
-6.243
- 0.462BTB
-810.334
- 0.3SLX-210.136
- 0.3SLY - 1SLZ - 1.54NL
Max Mz 26205 2104 1.15DL
25143
+ 1.2SIDL
5697.907
+ 1.4CL +97.842
1.4PLB + 1.54TLB
10.147 - 1.54BTB
15.129 68.893 906.728
Min Mz 26205 1452 1.15DL
25143
+ 1.2SIDL
3939.893
- 1.5COL(-X)-MLC
-49.144 0.187 -3.165 -27.382 -936.664

ODE MDE
Maximum Tension Force (kN) 1477.01 1198.575
Skin Friction (kN) 1722.67
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 1199 721.9 915.1 0.789 OK
Minima 5742 591 1701 0.348 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 81.98 OK
Minima -26.09 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 6.97 OK 48.56 OK
Minima 4.138 OK 30.76 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.7645 m
Hence de = 0.743 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 542 kN
Corresponding axial compressive force, N = 3940 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 4536 mm2
Effective area of tensile steel = 50% of total steel = As = 0.0023 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.339 %
Horizontal shear force, Vu = 542 kN
Shear stress (vv = Vu /(bv . dv) = 810.20 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.515 Mpa
= 515 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 478.933 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/Ac) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.25
Modified shear strength of concrete (n s vc ) = 599.06 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 141.26 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.61 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C7, C9 TO C12 & C14


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C7, C9 to C12 & C14

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30628 1001 1DL29632
+ 1SIDL 6075.359
+ 1CL + 1PLA +28.587
1.1TLA + 29.307
1.1BTA -0.111 -73.01 -10.642
Min Fx 24151 1004 1DL22919
+ 1SIDL +4009.49
1CL + 1PLB +10.801
1.1TLB - 1.1BTB
-0.593 -0.583 -0.8 23.473
Max Fy 30645 1005 1DL29631
+ 1SIDL 6034.443
+ 1CL + 1PLA +68.805
1PLB + 1.1TLA
48.185
+ 1.1TLB
-0.107
+ 1.1BTA
-188.613
+ 1.1BTB 131.345
Min Fy 24147 1006 1DL22885
+ 1SIDL 5004.774
+ 1CL + 1PLA -23.417
+ 1PLB + 1.1TLA
20.965
+ 1.1TLB
-1.707
- 1.1BTA -86.091
- 1.1BTB -40.731
Max Fz 30645 1005 1DL29631
+ 1SIDL 6034.443
+ 1CL + 1PLA +68.805
1PLB + 1.1TLA
48.185
+ 1.1TLB
-0.107
+ 1.1BTA
-188.613
+ 1.1BTB 131.345
Min Fz 30640 1005 1DL29644
+ 1SIDL 6034.443
+ 1CL + 1PLA -14.162
+ 1PLB + 1.1TLA
-7.189
+ 1.1TLB
-0.107
+ 1.1BTA +40.432
1.1BTB -60.952
Max Mx 24217 1005 1DL22985
+ 1SIDL 5451.829
+ 1CL + 1PLA +11.021
1PLB + 1.1TLA
5.651
+ 1.1TLB 2.62
+ 1.1BTA-21.721
+ 1.1BTB -73.4
Min Mx 24118 1006 1DL22886
+ 1SIDL 5004.774
+ 1CL + 1PLA -10.734
+ 1PLB + 1.1TLA
13.097
+ 1.1TLB
-1.707
- 1.1BTA -31.323
- 1.1BTB 15.758
Max My 30635 1005 1DL29640
+ 1SIDL 6034.443
+ 1CL + 1PLA +-7.449
1PLB + 1.1TLA
2.457
+ 1.1TLB
-0.107
+ 1.1BTA +59.087
1.1BTB -116.242
Min My 30645 1001 1DL29631
+ 1SIDL 6075.359
+ 1CL + 1PLA +57.651
1.1TLA + 46.476
1.1BTA -0.111 -194.751 131.031
Max Mz 30645 1005 1DL29631
+ 1SIDL 6034.443
+ 1CL + 1PLA +68.805
1PLB + 1.1TLA
48.185
+ 1.1TLB
-0.107
+ 1.1BTA
-188.613
+ 1.1BTB 131.345
Min Mz 30633 1005 1DL29638
+ 1SIDL 6034.443
+ 1CL + 1PLA + 1.727
1PLB + 1.1TLA
10.062
+ 1.1TLB
-0.107
+ 1.1BTA +48.619
1.1BTB -124.601

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24217 2039 1DL22985
+ 1SIDL 7003.437
+ 0.3CL + 0.3PLA
57.353
+ 0.33TLA73.104
+ 0.33BTA4.165
+ 0.3SLX261.447
+ 1SLY + 0.3SLZ
189.035+ 1.1LLA
Min Fx 24118 1023 1DL22887
+ 1SIDL 1690.469
+ 0.3SLX + 1SLY
-59.66
+ 0.3SLZ -54.881 -2.99 -285.624 -233.009
Max Fy 30645 1152 1DL29631
+ 1SIDL 4865.623
- 1COL(-X)-MLC
393.733 35.901 0.914 -143.519 880.419
Min Fy 24147 1086 1DL22885
+ 1SIDL 3034.956
+ 0.3CL + 0.3PLA
-237.678
+ 0.3PLB-87.543
+ 0.33TLA +-6.042
0.33TLB-188.004
- 0.33BTA - -190.531
0.33BTB - 1SLX - 0.3SLY
Max Fz 24444 3054 1DL23215
+ 1SIDL 6004.908
+ 0.3CL + 0.3PLA
69.285
+ 0.33TLA
294.543
- 0.33BTA3.124
- 0.3SLX 262.448
- 0.3SLY - 1SLZ
55.176
- 1.1NLA
Min Fz 24444 3047 1DL23215
+ 1SIDL 2653.535
+ 0.3CL + 0.3PLA
-50.989
+ 0.33TLA
-272.277
+ 0.33BTA
-3.546
+ 0.3SLX
-345.847
+ 0.3SLY +-72.532
1SLZ + 1.1NLA
Max Mx 24489 1086 1DL23268
+ 1SIDL 4857.102
+ 0.3CL + 0.3PLA
83.665
+ 0.3PLB61.183
+ 0.33TLA + 0.33TLB
9.68 -216.164
0.33BTA - 0.33BTB
458.692- 1SLX - 0.3SLY
Min Mx 24489 1055 1DL23268
+ 1SIDL 3106.167
+ 0.3CL + 0.3PLB
-82.875
+ 0.33TLB
-27.095
+ 0.33BTB
-9.01
+ 1SLX
-249.691
+ 0.3SLY + -500.166
0.3SLZ
Max My 24493 3071 1DL23271
+ 1SIDL 5164.024
+ 0.3CL + 0.3PLB
1.899
+ 0.33TLB32.396
+ 0.33BTB
4.929
+ 0.3SLX
710.293
+ 0.3SLY +143.712
1SLZ + 1.1NLB
Min My 24153 3047 1DL22922
+ 1SIDL 3546.632
+ 0.3CL + 0.3PLA
-6.468
+ 0.33TLA
-22.849
+ 0.33BTA
-3.849
+ 0.3SLX-712.62
+ 0.3SLY-222.897
+ 1SLZ + 1.1NLA
Max Mz 30645 1152 1DL29631
+ 1SIDL 4865.623
- 1COL(-X)-MLC
393.733 35.901 0.914 -143.519 880.419
Min Mz 30634 1152 1DL29639
+ 1SIDL 4865.623
- 1COL(-X)-MLC 6.32 6.237 0.914 41.266 -667.843
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24217 2339 1.15DL
22985
+ 1.2SIDL
8259.261
+ 0.42CL69.709
+ 0.42PLA +88.151
0.462TLA +5.106
0.462BTA
320.991
+ 0.3SLX231.468
+ 1SLY + 0.3SLZ + 1.5
Min Fx 24118 2123 1.15DL
22887
+ 1.2SIDL
1848.324
+ 0.3SLX-72.216
+ 1SLY + 0.3SLZ
-66.95 -3.652 -351.665 -285.732
Max Fy 30645 1452 1.15DL
29631
+ 1.2SIDL
5643.55
- 1.5COL(-X)-MLC
578.712 42.439 1.511 -168.813 1287.111
Min Fy 24518 2104 1.15DL
23297
+ 1.2SIDL
4426.242
+ 1.4CL-434.348
+ 1.4PLB + 1.54TLB
-3.575 - -15.886
1.54BTB -223.033 -179.292
Max Fz 30645 1453 1.15DL
29631
+ 1.2SIDL
5312.12
+ 1.5COL(Z)-MLC
36.505 369.017 -2.087 -733.207 108.128
Min Fz 24444 3147 1.15DL
23215
+ 1.2SIDL
2995.911
+ 0.42CL-64.381
+ 0.42PLA +-341.43
0.462TLA-4.425
+ 0.462BTA
-423.789
+ 0.3SLX-90.895
+ 0.3SLY + 1SLZ + 1.5
Max Mx 24489 2104 1.15DL
23267
+ 1.2SIDL
5958.587
+ 1.4CL159.053
+ 1.4PLB + 1.54TLB
46.48 - 1.54BTB
17.478 43.667 732.21
Min Mx 24489 2103 1.15DL
23268
+ 1.2SIDL
4462.722
+ 1.4CL-153.322
+ 1.4PLB + 1.54TLB
-0.005 + 1.54BTB
-16.42 -99.29 -968.799
Max My 24493 3171 1.15DL
23271
+ 1.2SIDL
6114.13
+ 0.42CL +2.485
0.42PLB +39.761
0.462TLB6.156
+ 0.462BTB
891.207
+ 0.3SLX181.039
+ 0.3SLY + 1SLZ + 1.5
Min My 24153 3147 1.15DL
22922
+ 1.2SIDL
4117.896
+ 0.42CL -8.491
+ 0.42PLA +-28.134
0.462TLA-4.822
+ 0.462BTA
-894.818
+ 0.3SLX-278.828
+ 0.3SLY + 1SLZ + 1.5
Max Mz 30645 1452 1.15DL
29631
+ 1.2SIDL
5643.55
- 1.5COL(-X)-MLC
578.712 42.439 1.511 -168.813 1287.111
Min Mz 30631 2103 1.15DL
29636
+ 1.2SIDL
6132.919
+ 1.4CL + 1.4PLB
5.317 + 1.54TLB
11.297 + 1.54BTB
-9.448 -86.667 -1177.113

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 6075.359 4009.49 7790.000 OK
ODE Seismic 7003.437 1690.469 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 16 16
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 5644 1298 1695 0.766 OK
Minima 4426 286.2 1588 0.180 OK

N/M Curve for MDE


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 90.98 OK
Minima -8.558 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 9.875 OK 66.48 OK
Minima 4.747 OK 34.31 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.766 m
Hence de = 0.744 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 580 kN
Corresponding axial compressive force, N = 5644 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 3217 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0016 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.240 %
Horizontal shear force, Vu = 580 kN
Shear stress (vv = Vu /(bv . dv) = 866.79 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.459 Mpa
= 459 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 426.930 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.36
Modified shear strength of concrete (n s vc ) = 580.32 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 191.78 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.78 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C8 & C13


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C8 & C13

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24448 1001 1DL23218
+ 1SIDL 5089.116
+ 1CL + 1PLA +12.119
1.1TLA + 1.1BTA
10.9 0.013 -39.814 -43.224
Min Fx 30590 1004 1DL29593
+ 1SIDL 3518.528
+ 1CL + 1PLB -19.398
+ 1.1TLB - 1.1BTB
6.775 -0.68 -16.064 -29.82
Max Fy 24477 1005 1DL23217
+ 1SIDL 5037.427
+ 1CL + 1PLA +40.983
1PLB + 1.1TLA
16.288
+ 1.1TLB0.041
+ 1.1BTA-74.096
+ 1.1BTB 26.356
Min Fy 30607 1006 1DL29592
+ 1SIDL 3945.906
+ 1CL + 1PLA -50.228
+ 1PLB + 1.1TLA
9.386
+ 1.1TLB-1.05
- 1.1BTA -56.122
- 1.1BTB -135.465
Max Fz 24477 1006 1DL23217
+ 1SIDL 4989.827
+ 1CL + 1PLA +-2.254
1PLB + 1.1TLA
22.257
+ 1.1TLB
-0.768
- 1.1BTA -85.424
- 1.1BTB 31.498
Min Fz 24460 1006 1DL23230
+ 1SIDL 4989.827
+ 1CL + 1PLA + 1.475
1PLB + 1.1TLA
-3.369
+ 1.1TLB
-0.768
- 1.1BTA -18.716
1.1BTB 2.832
Max Mx 30590 1005 1DL29593
+ 1SIDL 4088.083
+ 1CL + 1PLA -12.826
+ 1PLB + 1.1TLA
9.322
+ 1.1TLB0.068
+ 1.1BTA-27.934
+ 1.1BTB -114.899
Min Mx 30590 1006 1DL29593
+ 1SIDL 3945.906
+ 1CL + 1PLA -26.403
+ 1PLB + 1.1TLA
7.098
+ 1.1TLB-1.05
- 1.1BTA -30.118
- 1.1BTB -10.234
Max My 24455 1006 1DL23226
+ 1SIDL 4989.827
+ 1CL + 1PLA + 3.087
1PLB + 1.1TLA + 11.1TLB
-0.768
- 1.1BTA -27.686
1.1BTB 12.078
Min My 24477 1002 1DL23217
+ 1SIDL 5064.582
+ 1CL + 1PLA + 8.507
1.1TLA - 18.524
1.1BTA -0.519 -87.271 30.283
Max Mz 30596 1006 1DL29600
+ 1SIDL 3945.906
+ 1CL + 1PLA +-2.878
1PLB + 1.1TLA
3.295
+ 1.1TLB-1.05
- 1.1BTA - 1.1BTB
5.015 78.01
Min Mz 30607 1001 1DL29592
+ 1SIDL 4086.324
+ 1CL + 1PLA -18.942
+ 1.1TLA + 11.387
1.1BTA 0.009 -67.425 -144.947

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24448 2047 1DL23218
+ 1SIDL 5375.403
+ 0.3CL + 0.3PLA
32.591
+ 0.33TLA
103.418
+ 0.33BTA3.281
+ 0.3SLX 551.11
+ 0.3SLY 118.206
+ 1SLZ + 1.1LLA
Min Fx 30590 1007 1DL29594
+ 1SIDL 2476.564
+ 1SLX + 0.3SLY
-78.038
+ 0.3SLZ -20.873 -5.601 -254.46 -544.891
Max Fy 24477 1152 1DL23217
+ 1SIDL 4039.322
- 1COL(-X)-MLC
364.849 7.413 -0.208 -56.97 781.045
Min Fy 30607 1086 1DL29592
+ 1SIDL + 0.3CL
2700.9
+ 0.3PLA
-221.224
+ 0.3PLB-71.894
+ 0.33TLA +-5.825
0.33TLB-111.915
- 0.33BTA - -161.314
0.33BTB - 1SLX - 0.3SLY
Max Fz 24477 3054 1DL23248
+ 1SIDL 5342.862
+ 0.3CL + 0.3PLA
79.56
+ 0.33TLA
277.799
- 0.33BTA3.204
- 0.3SLX260.151
- 0.3SLY - 1SLZ
75.704
- 1.1NLA
Min Fz 24477 3047 1DL23248
+ 1SIDL +3142.93
0.3CL + 0.3PLA
-50.191
+ 0.33TLA
-245.225
+ 0.33BTA
-3.716
+ 0.3SLX
-369.605
+ 0.3SLY + -65.41
1SLZ + 1.1NLA
Max Mx 30590 3055 1DL29593
+ 1SIDL 4032.446
+ 0.3CL + 0.3PLB
50.536
+ 0.33TLB 33.92
+ 0.33BTB
5.204
+ 1SLX203.273
+ 0.3SLY + 0.3SLZ
398.797+ 1.1NLB
Min Mx 30590 3062 1DL29593
+ 1SIDL 2577.402
+ 0.3CL + 0.3PLB
-79.815
+ 0.33TLB
-21.246
- 0.33BTB
-5.911
- 1SLX-242.278
- 0.3SLY - 0.3SLZ
-496.058
- 1.1NLB
Max My 24451 3071 1DL23221
+ 1SIDL 5146.329
+ 0.3CL + 0.3PLB
3.793
+ 0.33TLB20.688
+ 0.33BTB
3.334
+ 0.3SLX699.52
+ 0.3SLY +136.898
1SLZ + 1.1NLB
Min My 30592 3047 1DL29596
+ 1SIDL 2906.372
+ 0.3CL + 0.3PLA
-21.218
+ 0.33TLA-4.835
+ 0.33BTA
-3.963
+ 0.3SLX
-702.797
+ 0.3SLY-194.776
+ 1SLZ + 1.1NLA
Max Mz 24477 1151 1DL23217
+ 1SIDL 4023.438
+ 1COL(X)-MLC342.699 5.241 2.047 -60.009 782.987
Min Mz 24454 1152 1DL23225
+ 1SIDL 4039.322
- 1COL(-X)-MLC2.743 3.734 -0.208 0.035 -629.648
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24448 2347 1.15DL
23218
+ 1.2SIDL
6377.736
+ 0.42CL +40.46
0.42PLA 127.908
+ 0.462TLA + 4.15
0.462BTA
691.101
+ 0.3SLX148.171
+ 0.3SLY + 1SLZ + 1.5
Min Fx 30590 2107 1.15DL
29594
+ 1.2SIDL
2773.748
+ 1SLX +-96.545
0.3SLY + 0.3SLZ
-26.835 -7 -317.887 -681.382
Max Fy 24477 1452 1.15DL
23217
+ 1.2SIDL
4699.926
- 1.5COL(-X)-MLC
542.84 5.492 -0.224 -62.477 1165.973
Min Fy 30607 2104 1.15DL
29611
+ 1.2SIDL
3000.648
+ 1.4CL -402.57
+ 1.4PLB + 1.54TLB
-15.277 - 1.54BTB
-9.686 -130.05 -512.468
Max Fz 24477 1453 1.15DL
23217
+ 1.2SIDL
4251.657
+ 1.5COL(Z)-MLC
14.792 349.745 0.58 -645.556 18.061
Min Fz 24477 3147 1.15DL
23248
+ 1.2SIDL
3606.917
+ 0.42CL-63.362
+ 0.42PLA-308.509
+ 0.462TLA-4.634
+ 0.462BTA
-454.834
+ 0.3SLX +-81.57
0.3SLY + 1SLZ + 1.5
Max Mx 30590 2103 1.15DL
29593
+ 1.2SIDL
5425.085
+ 1.4CL102.754
+ 1.4PLB + 1.54TLB
20.061 + 1.54BTB
8.786 68.826 761.076
Min Mx 30590 2104 1.15DL
29594
+ 1.2SIDL
3000.648
+ 1.4CL-141.331
+ 1.4PLB + 1.54TLB
-3.017 - 1.54BTB
-9.686 -114.094 -990.607
Max My 24451 3171 1.15DL
23221
+ 1.2SIDL
6057.032
+ 0.42CL +4.524
0.42PLB +24.739
0.462TLB4.224
+ 0.462BTB
878.652
+ 0.3SLX172.899
+ 0.3SLY + 1SLZ + 1.5
Min My 30592 3147 1.15DL
29596
+ 1.2SIDL
3354.101
+ 0.42CL-25.718
+ 0.42PLA + -6.453
0.462TLA-4.957
+ 0.462BTA
-883.019
+ 0.3SLX-245.147
+ 0.3SLY + 1SLZ + 1.5
Max Mz 24477 1451 1.15DL
23217
+ 1.2SIDL
4676.101
+ 1.5COL(X)-MLC
509.616 2.234 3.159 -67.035 1168.886
Min Mz 24450 2103 1.15DL
23221
+ 1.2SIDL
4834.143
+ 1.4CL + 1.4PLB
-26.2 + 1.54TLB
-2.892 + 1.54BTB
-8.267 -75.063 -1127.284

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 5089.116 3518.528 7790.000 OK
ODE Seismic 5375.403 2476.564 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 16 16
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 3001 997.2 1361 0.733 OK
Minima 3607 462.1 1469 0.315 OK

N/M Curve for MDE


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 83.86 OK
Minima -24.43 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 7.207 OK 49.88 OK
Minima 3.445 OK 27.15 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.766 m
Hence de = 0.744 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 543 kN
Corresponding axial compressive force, N = 4700 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 3217 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0016 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.240 %
Horizontal shear force, Vu = 543 kN
Shear stress (vv = Vu /(bv . dv) = 810.92 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.459 Mpa
= 459 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 426.930 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.30
Modified shear strength of concrete (n s vc ) = 554.67 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 171.55 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.78 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C15, C16, C49 & C50


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C15, C16, C49, C50

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24316 1002 1DL23084
+ 1SIDL 6618.186
+ 1CL + 1PLA +-4.901
1.1TLA - 23.408
1.1BTA -0.769 -74.851 -5.363
Min Fx 26429 1002 1DL25367
+ 1SIDL 3755.331
+ 1CL + 1PLA +-0.817
1.1TLA - -8.292
1.1BTA -0.772 -16.033 -1.87
Max Fy 26491 1005 1DL25399
+ 1SIDL 4564.023
+ 1CL + 1PLA +33.475
1PLB + 1.1TLA
-24.813
+ 1.1TLB-0.16
+ 1.1BTA 74.585
+ 1.1BTB 3.185
Min Fy 24312 1006 1DL23050
+ 1SIDL 5983.984
+ 1CL + 1PLA-21.629
+ 1PLB + 1.1TLA
43.893
+ 1.1TLB
-0.997
- 1.1BTA
-189.696
- 1.1BTB -33.121
Max Fz 24312 1005 1DL23050
+ 1SIDL 5977.864
+ 1CL + 1PLA +22.374
1PLB + 1.1TLA
48.365
+ 1.1TLB
-0.024
+ 1.1BTA
-189.696
+ 1.1BTB -36.324
Min Fz 26491 1006 1DL25399
+ 1SIDL 4573.755
+ 1CL + 1PLA-10.229
+ 1PLB + 1.1TLA
-29.616
+ 1.1TLB
-0.929
- 1.1BTA -72.287
1.1BTB 1.486
Max Mx 24316 1005 1DL23084
+ 1SIDL 6557.012
+ 1CL + 1PLA + 6.712
1PLB + 1.1TLA
25.133
+ 1.1TLB0.038
+ 1.1BTA +-56.57
1.1BTB -81.082
Min Mx 24283 1006 1DL23051
+ 1SIDL 5983.984
+ 1CL + 1PLA +-9.598
1PLB + 1.1TLA
28.084
+ 1.1TLB
-0.997
- 1.1BTA-74.235
- 1.1BTB 18.676
Max My 26491 1003 1DL25399
+ 1SIDL 4610.402
+ 1CL + 1PLB + 22.41
1.1TLB +-24.224
1.1BTB -0.396 80.137 2.632
Min My 24312 1002 1DL23050
+ 1SIDL 6045.939
+ 1CL + 1PLA-10.666
+ 1.1TLA - 43.663
1.1BTA -0.79 -196.431 -34.01
Max Mz 24287 1006 1DL23056
+ 1SIDL 5983.984
+ 1CL + 1PLA +-0.921
1PLB + 1.1TLA
13.201
+ 1.1TLB
-0.997
- 1.1BTA -26.333
1.1BTB 42.641
Min Mz 26464 1005 1DL25403
+ 1SIDL 4564.023
+ 1CL + 1PLA + 2.455
1PLB + 1.1TLA-8.19
+ 1.1TLB-0.16
+ 1.1BTA-20.372
+ 1.1BTB -93.315

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24316 2039 1DL23084
+ 1SIDL 7175.811
+ 0.3CL + 0.3PLA
28.225
+ 0.33TLA
109.165
+ 0.33BTA1.865
+ 0.3SLX
316.241
+ 1SLY + 110.277
0.3SLZ + 1.1LLA
Min Fx 26429 1015 1DL25368
+ 1SIDL 2120.579
+ 0.3SLX + 0.3SLY
-23.132
+ 1SLZ-112.614 -4.018 -663.393 -178.967
Max Fy 26491 1152 1DL25399
+ 1SIDL 3718.252
- 1COL(-X)-MLC
363.768 -14.767 0.288 46.396 777.262
Min Fy 24345 1086 1DL23083
+ 1SIDL 5155.033
+ 0.3CL + 0.3PLA
-221.247
+ 0.3PLB-97.086
+ 0.33TLA -6.066
+ 0.33TLB-286.403
- 0.33BTA - -115.278
0.33BTB - 1SLX - 0.3SLY - 0.3SLZ
Max Fz 24312 3054 1DL23081
+ 1SIDL 6430.199
+ 0.3CL + 0.3PLA
68.115
+ 0.33TLA
308.071
- 0.33BTA3.384
- 0.3SLX149.364
- 0.3SLY - 1SLZ
45.326
- 1.1NLA
Min Fz 26458 3078 1DL25366
+ 1SIDL 2439.964
+ 0.3CL + 0.3PLB
-62.771
+ 0.33TLB
-300.092
- 0.33BTB
-4.32
- 0.3SLX
-98.998
- 0.3SLY - 1SLZ
-40.631
- 1.1NLB
Max Mx 24316 3055 1DL23084
+ 1SIDL 6225.341
+ 0.3CL + 0.3PLB
76.099
+ 0.33TLB70.669
+ 0.33BTB
5.339+ 1SLX249.526
+ 0.3SLY + 384.937
0.3SLZ + 1.1NLB
Min Mx 24316 3062 1DL23084
+ 1SIDL 4975.195
+ 0.3CL + 0.3PLB
-81.517
+ 0.33TLB
-34.608
- 0.33BTB
-6.22
- 1SLX-338.301
- 0.3SLY - 0.3SLZ
-441.636
- 1.1NLB
Max My 24287 3071 1DL23055
+ 1SIDL 6194.495
+ 0.3CL + 0.3PLB
3.954
+ 0.33TLB35.557
+ 0.33BTB
3.523+ 0.3SLX
727.582
+ 0.3SLY 149.185
+ 1SLZ + 1.1NLB
Min My 26464 3047 1DL25403
+ 1SIDL 2862.362
+ 0.3CL + 0.3PLA
-6.404
+ 0.33TLA
-30.872
+ 0.33BTA
-4.182
+ 0.3SLX
-739.861
+ 0.3SLY-207.441
+ 1SLZ + 1.1NLA
Max Mz 26491 1152 1DL25399
+ 1SIDL 3718.252
- 1COL(-X)-MLC
363.768 -14.767 0.288 46.396 777.262
Min Mz 26468 1152 1DL25407
+ 1SIDL 3718.252
- 1COL(-X)-MLC2.604 -1.434 0.288 -20.895 -628.238
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24316 2339 1.15DL
23084
+ 1.2SIDL
8401.426
+ 0.42CL35.581
+ 0.42PLA 130.751
+ 0.462TLA +2.390.462BTA
387.092
+ 0.3SLX138.784
+ 1SLY + 0.3SLZ + 1.54LLA
Min Fx 26429 2115 1.15DL
25368
+ 1.2SIDL
2314.916
+ 0.3SLX-29.008
+ 0.3SLY +-139.521
1SLZ -4.997 -830.405 -222.195
Max Fy 26491 1452 1.15DL
25399
+ 1.2SIDL
4276.649
- 1.5COL(-X)-MLC
542.723 -16.038 0.568 53.805 1165.739
Min Fy 24345 2104 1.15DL
23114
+ 1.2SIDL
6840.848
+ 1.4CL-417.808
+ 1.4PLB + -24.213
1.54TLB - -10.115
1.54BTB -167.042 -298.576
Max Fz 24312 3154 1.15DL
23081
+ 1.2SIDL
7622.963
+ 0.42CL84.745
+ 0.42PLA 382.999
+ 0.462TLA - 0.462BTA
4.3 193.604
- 0.3SLX -58.343
0.3SLY - 1SLZ - 1.54NLA
Min Fz 26458 3178 1.15DL
25366
+ 1.2SIDL
2762.056
+ 0.42CL-79.518
+ 0.42PLB-374.166
+ 0.462TLB-5.421
- 0.462BTB
-120.905
- 0.3SLX - 0.3SLY
-48.35 - 1SLZ - 1.54NLB
Max Mx 24316 2103 1.15DL
23084
+ 1.2SIDL
7172.364
+ 1.4CL149.384
+ 1.4PLB + 1.54TLB
39.591 + 1.54BTB
8.894 78.682 726.64
Min Mx 24316 2104 1.15DL
23085
+ 1.2SIDL
6840.848
+ 1.4CL-151.961
+ 1.4PLB + 1.54TLB
1.687 - -10.115
1.54BTB -182.332 -939.945
Max My 24287 3171 1.15DL
23055
+ 1.2SIDL
7292.978
+ 0.42CL +5.014
0.42PLB +43.313
0.462TLB4.496
+ 0.462BTB
913.319
+ 0.3SLX187.435
+ 0.3SLY + 1SLZ + 1.54NLB
Min My 26464 3147 1.15DL
25403
+ 1.2SIDL
3226.369
+ 0.42CL -7.958
+ 0.42PLA +-37.165
0.462TLA-5.229
+ 0.462BTA
-927.828
+ 0.3SLX-259.824
+ 0.3SLY + 1SLZ + 1.54NLA
Max Mz 26491 1452 1.15DL
25399
+ 1.2SIDL
4276.649
- 1.5COL(-X)-MLC
542.723 -16.038 0.568 53.805 1165.739
Min Mz 24318 2103 1.15DL
23087
+ 1.2SIDL
6822.608
+ 1.4CL -39.398
+ 1.4PLB + 1.54TLB
10.748 + 1.54BTB
-9.673 -157.788 -1143.421

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 6618.186 3755.331 7790.000 OK
ODE Seismic 7175.811 2120.579 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


1st Layer 16 16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 4277 1167 1569 0.744 OK
Minima 2762 130.2 1313 0.099 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 94.76 OK
Minima -48.56 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 10.86 OK 66.68 OK
Minima -1.621 OK -0.7061 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.127 mm OK

2.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.766 m
Hence de = 0.744 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 543 kN
Corresponding axial compressive force, N = 4277 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 3217 mm2
Effective area of tensile steel = 50% of total steel = As = 0.0016 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.240 %
Horizontal shear force, Vu = 543 kN
Shear stress (vv = Vu /(bv . dv) = 811.06 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.459 Mpa
= 459 kN/m2
1/4
Depth Factor, s = (500/d) or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 426.930 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/Ac) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.27
Modified shear strength of concrete (n s vc ) = 543.17 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 179.34 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.78 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C17 & C51


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C17, C51

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24184 1001 1DL22952
+ 1SIDL +4947.235
1CL + 1PLA +24.857
1.1TLA + 1.1BTA
8.349 0.476 -37.68 -17.951
Min Fx 26330 1002 1DL25268
+ 1SIDL +2706.082
1CL + 1PLA + 9.254
1.1TLA - 1.1BTA
-5.913 -1.203 -25.365 15.522
Max Fy 24213 1005 1DL22951
+ 1SIDL +4942.872
1CL + 1PLA +60.595
1PLB + 1.1TLA
12.722
+ 1.1TLB 0.626
+ 1.1BTA +-61.461
1.1BTB 100.894
Min Fy 24194 1005 1DL22962
+ 1SIDL +4942.872
1CL + 1PLA -13.789
+ 1PLB + 1.1TLA
-1.037
+ 1.1TLB 0.626
+ 1.1BTA +12.828
1.1BTB -81.424
Max Fz 24213 1005 1DL22951
+ 1SIDL +4942.872
1CL + 1PLA +60.595
1PLB + 1.1TLA
12.722
+ 1.1TLB 0.626
+ 1.1BTA +-61.461
1.1BTB 100.894
Min Fz 26359 1006 1DL25267
+ 1SIDL + 3100.71
1CL + 1PLA + 1PLB
5.972+ 1.1TLA
-17.332
+ 1.1TLB-1.526
- 1.1BTA - 1.1BTB
24.137 59.621
Max Mx 24184 1005 1DL22952
+ 1SIDL +4942.872
1CL + 1PLA +27.459
1PLB + 1.1TLA
8.595
+ 1.1TLB0.626
+ 1.1BTA +-27.448
1.1BTB -44.901
Min Mx 26330 1006 1DL25268
+ 1SIDL + 3100.71
1CL + 1PLA + 1PLB
6.197+ 1.1TLA
-7.522
+ 1.1TLB-1.526
- 1.1BTA --17.165
1.1BTB 41.055
Max My 26359 1003 1DL25267
+ 1SIDL +3272.583
1CL + 1PLB + 32.83
1.1TLB + -11.345
1.1BTB -0.99 31.937 39.802
Min My 24213 1001 1DL22951
+ 1SIDL +4947.235
1CL + 1PLA +51.437
1.1TLA + 1.1BTA
10.7 0.476 -67.634 107.671
Max Mz 24213 1006 1DL22951
+ 1SIDL +4847.166
1CL + 1PLA +22.771
1PLB + 1.1TLA5.28
+ 1.1TLB-0.334
- 1.1BTA --57.633
1.1BTB 126.212
Min Mz 24189 1005 1DL22958
+ 1SIDL +4942.872
1CL + 1PLA + 1PLB
0.167+ 1.1TLA
3.725
+ 1.1TLB 0.626
+ 1.1BTA + 1.1BTB
8.174 -115.644

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24184 3047 1DL22952
+ 1SIDL +6086.388
0.3CL + 0.3PLA
43.771
+ 0.33TLA
115.952
+ 0.33BTA 3.576
+ 0.3SLX553.283
+ 0.3SLY +154.616
1SLZ + 1.1NLA
Min Fx 26330 1015 1DL25269
+ 1SIDL +1247.368
0.3SLX + 0.3SLY
-14.629
+ 1SLZ-102.429 -4.353 -658.803 -176.682
Max Fy 24213 1152 1DL22951
+ 1SIDL -4235.981
1COL(-X)-MLC
389.666 15.912 2.321 -60.967 864.161
Min Fy 26359 1086 1DL25267
+ 1SIDL +1981.054
0.3CL + 0.3PLA
-171.644
+ 0.3PLB-132.07
+ 0.33TLA + 0.33TLB
-6.27 - 0.33BTA
-43.611 - 0.33BTB
-14.135- 1SLX - 0.3SLY
Max Fz 24213 3071 1DL22951
+ 1SIDL +5894.908
0.3CL + 0.3PLB
104.635
+ 0.33TLB
303.199
+ 0.33BTB3.988
+ 0.3SLX
121.512
+ 0.3SLY + 149.225
1SLZ + 1.1NLB
Min Fz 26359 3078 1DL25267
+ 1SIDL +1403.273
0.3CL + 0.3PLB
-46.962
+ 0.33TLB
-286.047
- 0.33BTB
-4.731
- 0.3SLX-69.068
- 0.3SLY - 1SLZ-4.792
- 1.1NLB
Max Mx 24184 3055 1DL22952
+ 1SIDL +5362.855
0.3CL + 0.3PLB
84.963
+ 0.33TLB 64.425
+ 0.33BTB5.897
+ 1SLX 257.815
+ 0.3SLY + 0.3SLZ
453.208
+ 1.1NLB
Min Mx 26330 3062 1DL25268
+ 1SIDL +1991.607
0.3CL + 0.3PLB
-53.27
+ 0.33TLB-50.771
- 0.33BTB
-6.431
- 1SLX -253.365
- 0.3SLY - 0.3SLZ
-446.595
- 1.1NLB
Max My 24187 3071 1DL22955
+ 1SIDL +5894.908
0.3CL + 0.3PLB
13.603
+ 0.33TLB 17.789
+ 0.33BTB3.988
+ 0.3SLX
725.455
+ 0.3SLY + 128.519
1SLZ + 1.1NLB
Min My 26332 3047 1DL25271
+ 1SIDL +1276.222
0.3CL + 0.3PLA
-1.712
+ 0.33TLA-27.987
+ 0.33BTA-4.559
+ 0.3SLX
-746.914
+ 0.3SLY +-211.008
1SLZ + 1.1NLA
Max Mz 24213 1151 1DL22951
+ 1SIDL +4119.743
1COL(X)-MLC369.34 32.745 3.854 -60.585 873.547
Min Mz 24190 1152 1DL22959
+ 1SIDL -4235.981
1COL(-X)-MLC5.614 2.528 2.321 19.11 -663.169
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24184 3147 1.15DL
22952
+ 1.2SIDL
7210.611
+ 0.42CL 52.897
+ 0.42PLA + 143.35
0.462TLA +4.462
0.462BTA
693.133
+ 0.3SLX 191.154
+ 0.3SLY + 1SLZ + 1.54
Min Fx 26330 2115 1.15DL
25269
+ 1.2SIDL
1296.447
+ 0.3SLX-19.109
+ 0.3SLY + -127.712
1SLZ -5.374 -825.413 -219.716
Max Fy 24213 1452 1.15DL
22951
+ 1.2SIDL
4875.586
- 1.5COL(-X)-MLC
571.712 19.806 3.476 -69.878 1259.783
Min Fy 26359 2104 1.15DL
25298
+ 1.2SIDL
2992.33
+ 1.4CL-333.702
+ 1.4PLB + 1.54TLB
-92.631 - 1.54BTB
-10.27 -28.682 -357.832
Max Fz 24213 3171 1.15DL
22951
+ 1.2SIDL
6942.54
+ 0.42CL127.964
+ 0.42PLB +378.091
0.462TLB 5.039
+ 0.462BTB
150.546
+ 0.3SLX +174.619
0.3SLY + 1SLZ + 1.54
Min Fz 26359 3178 1.15DL
25267
+ 1.2SIDL
1514.714
+ 0.42CL-60.864
+ 0.42PLB -357.998
+ 0.462TLB-5.903
- 0.462BTB
-85.997
- 0.3SLX - 0.3SLY
-7.297- 1SLZ - 1.54N
Max Mx 24184 2103 1.15DL
22952
+ 1.2SIDL
6114.067
+ 1.4CL 147.784
+ 1.4PLB + 1.54TLB
33.793 + 1.54BTB
9.556 115.131 824.127
Min Mx 26330 2104 1.15DL
25269
+ 1.2SIDL
2992.33
+ 1.4CL-103.645
+ 1.4PLB + 1.54TLB
-36.379 - 1.54BTB
-10.27 -180.938 -946.311
Max My 24187 3171 1.15DL
22955
+ 1.2SIDL
6942.54
+ 0.42CL 16.046
+ 0.42PLB + 20.848
0.462TLB 5.039
+ 0.462BTB
912.846
+ 0.3SLX +163.261
0.3SLY + 1SLZ + 1.54
Min My 26332 3147 1.15DL
25271
+ 1.2SIDL
1336.843
+ 0.42CL +-2.388
0.42PLA +-34.617
0.462TLA +-5.662
0.462BTA
-937.321
+ 0.3SLX-263.788
+ 0.3SLY + 1SLZ + 1.54
Max Mz 24213 1451 1.15DL
22951
+ 1.2SIDL
4701.229
+ 1.5COL(X)-MLC
541.223 45.057 5.776 -69.304 1273.862
Min Mz 24186 2103 1.15DL
22955
+ 1.2SIDL
4307.561
+ 1.4CL + -4.837
1.4PLB + 1.54TLB
-1.918 + 1.54BTB
-9.346 -195.482 -1143.994

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 4947.235 2706.082 7790.000 OK
ODE Seismic 6086.388 1247.368 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 1337 973.7 1095 0.889 OK
Minima 1515 86.31 1141 0.076 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 90.67 OK
Minima -188 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 7.331 OK 50.16 OK
Minima 3.037 OK 22.2 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 16.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24199 1001 1DL22967
+ 1SIDL +4947.235
1CL + 1PLA +-6.691
1.1TLA + 1.1BTA
-1.136 0.476 5.346 -17.264
Min Fx 26345 1002 1DL25283
+ 1SIDL +2706.082
1CL + 1PLA +-1.927
1.1TLA - 1.1BTA
2.128 -1.203 -4.325 -6.197
Max Fy 28632 1005 1DL27616
+ 1SIDL +4942.872
1CL + 1PLA + 1PLB
1.337+ 1.1TLA0.09
+ 1.1TLB 0.626
+ 1.1BTA + 1.1BTB
-0.45 4.347
Min Fy 24199 1005 1DL22967
+ 1SIDL +4942.872
1CL + 1PLA +-8.029
1PLB + 1.1TLA
-1.458
+ 1.1TLB 0.626
+ 1.1BTA + 1.1BTB
5.621 -19.331
Max Fz 26345 1006 1DL25283
+ 1SIDL + 3100.71
1CL + 1PLA +-0.511
1PLB + 1.1TLA
2.323
+ 1.1TLB-1.526
- 1.1BTA - 1.1BTB
-5.346 -3.833
Min Fz 24199 1005 1DL22967
+ 1SIDL +4942.872
1CL + 1PLA +-8.029
1PLB + 1.1TLA
-1.458
+ 1.1TLB 0.626
+ 1.1BTA + 1.1BTB
5.621 -19.331
Max Mx 24199 1005 1DL22967
+ 1SIDL +4942.872
1CL + 1PLA +-8.029
1PLB + 1.1TLA
-1.458
+ 1.1TLB0.626
+ 1.1BTA + 1.1BTB
5.621 -19.331
Min Mx 26345 1006 1DL25283
+ 1SIDL + 3100.71
1CL + 1PLA +-0.511
1PLB + 1.1TLA
2.323
+ 1.1TLB-1.526
- 1.1BTA - 1.1BTB
-5.346 -3.833
Max My 24199 1005 1DL22967
+ 1SIDL +4942.872
1CL + 1PLA +-8.029
1PLB + 1.1TLA
-1.458
+ 1.1TLB 0.626
+ 1.1BTA + 1.1BTB
5.621 -19.331
Min My 26345 1006 1DL25283
+ 1SIDL + 3100.71
1CL + 1PLA +-0.511
1PLB + 1.1TLA
2.323
+ 1.1TLB-1.526
- 1.1BTA - 1.1BTB
-5.346 -3.833
Max Mz 28629 1005 1DL27614
+ 1SIDL +4942.872
1CL + 1PLA +-0.667
1PLB + 1.1TLA
-0.421
+ 1.1TLB 0.626
+ 1.1BTA + -0.257
1.1BTB 5.858
Min Mz 24199 1005 1DL22967
+ 1SIDL +4942.872
1CL + 1PLA +-8.029
1PLB + 1.1TLA
-1.458
+ 1.1TLB 0.626
+ 1.1BTA + 1.1BTB
5.621 -19.331

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24199 3047 1DL22967
+ 1SIDL +6086.388
0.3CL + 0.3PLA3.711
+ 0.33TLA39.27
+ 0.33BTA3.576
+ 0.3SLX84.418
+ 0.3SLY + 1SLZ
2.485
+ 1.1NLA
Min Fx 26345 1015 1DL25284
+ 1SIDL +1247.368
0.3SLX + 0.3SLY
-11.592
+ 1SLZ -36.513 -4.353 -36.546 -12.512
Max Fy 26345 1086 1DL25284
+ 1SIDL +3542.057
0.3CL + 0.3PLA
24.649
+ 0.3PLB +18.301
0.33TLA + 0.33TLB
4.23 - 0.33BTA
13.545 - 0.33BTB
17.064
- 1SLX - 0.3SLY
Min Fy 24199 1152 1DL22967
+ 1SIDL -4235.981
1COL(-X)-MLC-50.415 -1.914 2.321 6.414 -132.665
Max Fz 26345 3078 1DL25284
+ 1SIDL +4140.943
0.3CL + 0.3PLB6.757
+ 0.33TLB 39.967
- 0.33BTB
2.369
- 0.3SLX - 0.3SLY
31.63 - 1SLZ4.607
- 1.1NLB
Min Fz 24199 3071 1DL22968
+ 1SIDL +2655.094
0.3CL + 0.3PLB
-14.153
+ 0.33TLB-41.751
+ 0.33BTB
-3.356
+ 0.3SLX-35.872
+ 0.3SLY + 1SLZ
-17.474
+ 1.1NLB
Max Mx 24199 3055 1DL22967
+ 1SIDL +5362.855
0.3CL + 0.3PLB
21.657
+ 0.33TLB 16.818
+ 0.33BTB
5.897
+ 1SLX +45.914
0.3SLY + 0.3SLZ
33.523
+ 1.1NLB
Min Mx 26345 3062 1DL25283
+ 1SIDL +1991.607
0.3CL + 0.3PLB
-28.884
+ 0.33TLB -14.59
- 0.33BTB
-6.431
- 1SLX - -37.248
0.3SLY - 0.3SLZ
-53.647
- 1.1NLB
Max My 24199 3071 1DL22967
+ 1SIDL +5894.908
0.3CL + 0.3PLB3.615
+ 0.33TLB 38.299
+ 0.33BTB
3.988
+ 0.3SLX85.919
+ 0.3SLY + 1SLZ
2.258
+ 1.1NLB
Min My 26345 3078 1DL25283
+ 1SIDL +1403.273
0.3CL + 0.3PLB
-11.41
+ 0.33TLB-35.991
- 0.33BTB
-4.731
- 0.3SLX-77.078
- 0.3SLY - 1SLZ
-23.967
- 1.1NLB
Max Mz 26345 1007 1DL25283
+ 1SIDL +3396.705
1SLX + 0.3SLY24.049
+ 0.3SLZ 18.043 4.447 28.879 40.907
Min Mz 24199 1152 1DL22967
+ 1SIDL -4235.981
1COL(-X)-MLC-50.415 -1.914 2.321 6.414 -132.665
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 24199 3147 1.15DL
22967
+ 1.2SIDL
7210.611
+ 0.42CL +5.036
0.42PLA + 49.323
0.462TLA +4.462
0.462BTA
104.514
+ 0.3SLX + 0.3SLY
4.252 + 1SLZ + 1.54
Min Fx 26345 2115 1.15DL
25284
+ 1.2SIDL
1296.447
+ 0.3SLX-14.253
+ 0.3SLY + 1SLZ
-45.961 -5.374 -45.489 -15.165
Max Fy 26345 2104 1.15DL
25283
+ 1.2SIDL
4433.862
+ 1.4CL +48.043
1.4PLB + 1.54TLB
12.732 - 1.54BTB
7.423 12.281 80.178
Min Fy 24199 1452 1.15DL
22967
+ 1.2SIDL
4875.586
- 1.5COL(-X)-MLC
-74.014 -2.416 3.476 7.75 -194.33
Max Fz 26345 3178 1.15DL
25284
+ 1.2SIDL
4942.427
+ 0.42CL +8.744
0.42PLB + 50.04
0.462TLB 2.993
- 0.462BTB39.741
- 0.3SLX - 0.3SLY
6.067- 1SLZ - 1.54N
Min Fz 24199 3171 1.15DL
22968
+ 1.2SIDL
2916.458
+ 0.42CL-17.355
+ 0.42PLB + -52.14
0.462TLB-4.161
+ 0.462BTB
-44.889
+ 0.3SLX +-21.007
0.3SLY + 1SLZ + 1.54
Max Mx 24199 2103 1.15DL
22967
+ 1.2SIDL
6114.067
+ 1.4CL +42.726
1.4PLB + 1.54TLB
8.612 + 1.54BTB
9.556 24.283 68.316
Min Mx 26345 2104 1.15DL
25284
+ 1.2SIDL
2992.33
+ 1.4CL +-52.155
1.4PLB + 1.54TLB
-7.385 - 1.54BTB
-10.27 -13.778 -42.108
Max My 24199 1453 1.15DL
22967
+ 1.2SIDL
4386.795
+ 1.5COL(Z)-MLC
-5.129 -45.325 -2.3 114.686 -15.337
Min My 26345 3178 1.15DL
25283
+ 1.2SIDL
1514.714
+ 0.42CL-13.998
+ 0.42PLB +-45.229
0.462TLB-5.903
- 0.462BTB
-96.326
- 0.3SLX - 0.3SLY
-29.233- 1SLZ - 1.54N
Max Mz 26345 2104 1.15DL
25283
+ 1.2SIDL
4433.862
+ 1.4CL +48.043
1.4PLB + 1.54TLB
12.732 - 1.54BTB
7.423 12.281 80.178
Min Mz 24199 1452 1.15DL
22967
+ 1.2SIDL
4875.586
- 1.5COL(-X)-MLC
-74.014 -2.416 3.476 7.75 -194.33

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 4876 194.5 1634 0.119 OK
Minima 4942 40.21 1641 0.025 OK

Reinforcement Stresses for ODE


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 58.52 OK
Minima 8.116 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 6.339 OK 44.93 OK
Minima 3.286 OK 23.6 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.7645 m
Hence de = 0.743 m and dv = 0.669 m
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Horizontal resultant shear force at the section, Vu = 572 kN


Corresponding axial compressive force, N = 4876 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 4536 mm2
Effective area of tensile steel = 50% of total steel = As = 0.0023 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.339 %
Horizontal shear force, Vu = 572 kN
Shear stress (vv = Vu /(bv . dv) = 855.07 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.515 Mpa
= 515 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 478.933 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/Ac) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.31
Modified shear strength of concrete (n s vc ) = 627.59 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 152.19 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.61 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C18


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR C18

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 4
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28079 1005 1DL27059
+ 1SIDL 4789.497
+ 1CL + 1PLA105.253
+ 1PLB + 1.1TLA
-28.287
+ 1.1TLB
-0.888
+ 1.1BTA183.639
+ 1.1BTB 477.983
Min Fx 28080 1001 1DL27060
+ 1SIDL 3372.254
+ 1CL + 1PLA +50.093
1.1TLA + 1.1BTA
0.085 -0.602 -60.892 149.067
Max Fy 28079 1005 1DL27059
+ 1SIDL 4789.497
+ 1CL + 1PLA105.253
+ 1PLB + 1.1TLA
-28.287
+ 1.1TLB
-0.888
+ 1.1BTA183.639
+ 1.1BTB 477.983
Min Fy 28080 1006 1DL27060
+ 1SIDL 4514.154
+ 1CL + 1PLA + 1PLB
-22+ 1.1TLA
9.496
+ 1.1TLB
-0.722
- 1.1BTA -93.518
- 1.1BTB -119.259
Max Fz 28084 1006 1DL27064
+ 1SIDL 4514.154
+ 1CL + 1PLA -19.963
+ 1PLB + 1.1TLA
9.537
+ 1.1TLB
-0.722
- 1.1BTA -84.023
- 1.1BTB -97.258
Min Fz 28079 1005 1DL27059
+ 1SIDL 4789.497
+ 1CL + 1PLA105.253
+ 1PLB + 1.1TLA
-28.287
+ 1.1TLB
-0.888
+ 1.1BTA183.639
+ 1.1BTB 477.983
Max Mx 28081 1004 1DL27061
+ 1SIDL 3862.219
+ 1CL + 1PLB +25.558
1.1TLB - 1.1BTB
8.169 -0.183 -70.015 174.674
Min Mx 28078 1002 1DL27058
+ 1SIDL 3942.867
+ 1CL + 1PLA + 0.355
1.1TLA - -17.554
1.1BTA -1.062 116.458 -34.975
Max My 28079 1005 1DL27059
+ 1SIDL 4789.497
+ 1CL + 1PLA105.253
+ 1PLB + 1.1TLA
-28.287
+ 1.1TLB
-0.888
+ 1.1BTA183.639
+ 1.1BTB 477.983
Min My 28080 1002 1DL27060
+ 1SIDL +3794.16
1CL + 1PLA + 0.651
1.1TLA - 1.1BTA
8.228 -1.035 -95.514 -32.551
Max Mz 28081 1005 1DL27061
+ 1SIDL 4732.899
+ 1CL + 1PLA105.251
+ 1PLB + 1.1TLA
1.788
+ 1.1TLB
-0.701
+ 1.1BTA-63.476
+ 1.1BTB 477.985
Min Mz 28080 1006 1DL27060
+ 1SIDL 4514.154
+ 1CL + 1PLA + 1PLB
-22+ 1.1TLA
9.496
+ 1.1TLB
-0.722
- 1.1BTA -93.518
- 1.1BTB -119.259

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28081 1095 1DL27061
+ 1SIDL 8363.084
+ 0.3CL + 0.3PLA234.6
+ 0.3PLB791.358
+ 0.33TLA +9.656
0.33TLB3128.975
+ 0.33BTA +1004.667
0.33BTB + 0.3SLX + 0.
Min Fx 28078 1015 1DL27062
+ 1SIDL-1912.475
+ 0.3SLX + 0.3SLY
-159.177
+ 1SLZ -800.23 -10.773 -2323.797 -529.454
Max Fy 28079 1079 1DL27059
+ 1SIDL 7048.284
+ 0.3CL + 0.3PLA
625.992
+ 0.3PLB371.724
+ 0.33TLA 19.596
+ 0.33TLB1697.139
+ 0.33BTA +2586.795
0.33BTB + 1SLX + 0.3S
Min Fy 28080 1086 1DL27060
+ 1SIDL +-244.707
0.3CL + 0.3PLA
-563.087
+ 0.3PLB
-382.263
+ 0.33TLA +-19.58
0.33TLB-1639.269
- 0.33BTA -2320.144
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 28081 3071 1DL27061
+ 1SIDL 8245.954
+ 0.3CL + 0.3PLB
225.514
+ 0.33TLB
798.757
+ 0.33BTB9.163
+ 0.3SLX
3106.042
+ 0.3SLY +968.133
1SLZ + 1.1NLB
Min Fz 28078 3047 1DL27062
+ 1SIDL-1663.976
+ 0.3CL + 0.3PLA
-149.75
+ 0.33TLA
-808.968
+ 0.33BTA
-10.296
+ 0.3SLX
-2299.132
+ 0.3SLY-507.301
+ 1SLZ + 1.1NLA
Max Mx 28079 3062 1DL27063
+ 1SIDL 6765.038
+ 0.3CL + 0.3PLB
602.003
+ 0.33TLB
369.678
- 0.33BTB
20.316
- 1SLX1293.682
- 0.3SLY - 0.3SLZ
1893.909
- 1.1NLB
Min Mx 28079 3038 1DL27059
+ 1SIDL + -126.79
0.3CL + 0.3PLA
-534.383
+ 0.33TLA
-398.987
- 0.33BTA
-21.576
- 1SLX-1490.517
- 0.3SLY - -2114.221
0.3SLZ - 1.1NLA
Max My 28078 3047 1DL27058
+ 1SIDL 7980.512
+ 0.3CL + 0.3PLA
204.528
+ 0.33TLA
764.718
+ 0.33BTA 9.974
+ 0.3SLX
3323.529
+ 0.3SLY 794.933
+ 1SLZ + 1.1NLA
Min My 28081 3054 1DL27061
+ 1SIDL-1440.019
+ 0.3CL + 0.3PLA
-142.936
+ 0.33TLA
-774.647
- 0.33BTA
-11.493
- 0.3SLX
-3283.751
- 0.3SLY --531.639
1SLZ - 1.1NLA
Max Mz 28079 1079 1DL27059
+ 1SIDL 7048.284
+ 0.3CL + 0.3PLA
625.992
+ 0.3PLB371.724
+ 0.33TLA 19.596
+ 0.33TLB1697.139
+ 0.33BTA +2586.795
0.33BTB + 1SLX + 0.3S
Min Mz 28080 1086 1DL27060
+ 1SIDL +-244.707
0.3CL + 0.3PLA
-563.087
+ 0.3PLB
-382.263
+ 0.33TLA +-19.58
0.33TLB-1639.269
- 0.33BTA -2320.144
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28078 2104 1.15DL
27058
+ 1.2SIDL
11225.737
+ 1.4CL
1087.246
+ 1.4PLB + 322.166
1.54TLB - 1.54BTB
35.78 1518.751 4374.685
Min Fx 28078 2103 1.15DL
27062
+ 1.2SIDL
-3479.508
+ 1.4CL-1029.83
+ 1.4PLB + -351.935
1.54TLB + -36.372
1.54BTB -960.045 -3210.861
Max Fy 28081 2103 1.15DL
27061
+ 1.2SIDL
11182.503
+ 1.4CL
1181.323
+ 1.4PLB + 348.099
1.54TLB + 1.54BTB
34.06 1286.288 4834.514
Min Fy 28078 2104 1.15DL
27062
+ 1.2SIDL
-2950.789
+ 1.4CL -1098.7
+ 1.4PLB + -352.317
1.54TLB - -35.615
1.54BTB -955.807 -3394.528
Max Fz 28081 3171 1.15DL
27061
+ 1.2SIDL
10102.916
+ 0.42CL280.921
+ 0.42PLB1002.953
+ 0.462TLB 11.482
+ 0.462BTB
3900.142
+ 0.3SLX
1201.609
+ 0.3SLY + 1SLZ + 1.5
Min Fz 28078 3147 1.15DL
27062
+ 1.2SIDL
-2336.574
+ 0.42CL
-188.467
+ 0.42PLA
-1015.369
+ 0.462TLA-12.783
+ 0.462BTA
-2889.265
+ 0.3SLX-635.212
+ 0.3SLY + 1SLZ + 1.5
Max Mx 28079 2104 1.15DL
27059
+ 1.2SIDL
8388.827
+ 1.4CL
1109.498
+ 1.4PLB + 1.54TLB
311.48 - 1.54BTB
36.44 1424.257 4558.177
Min Mx 28079 2103 1.15DL
27063
+ 1.2SIDL45.79
+ 1.4CL-998.811
+ 1.4PLB + -342.017
1.54TLB + -37.025
1.54BTB -871.665 -2987.515
Max My 28078 3147 1.15DL
27058
+ 1.2SIDL
9773.19
+ 0.42CL256.167
+ 0.42PLA 959.927
+ 0.462TLA12.653
+ 0.462BTA
4166.039
+ 0.3SLX997.163
+ 0.3SLY + 1SLZ + 1.5
Min My 28081 3154 1.15DL
27061
+ 1.2SIDL
-2079.435
+ 0.42CL
-183.623
+ 0.42PLA-972.013
+ 0.462TLA-14.455
- 0.462BTA
-4119.101
- 0.3SLX-687.039
- 0.3SLY - 1SLZ - 1.54N
Max Mz 28081 2103 1.15DL
27061
+ 1.2SIDL
11182.503
+ 1.4CL
1181.323
+ 1.4PLB + 348.099
1.54TLB + 1.54BTB
34.06 1286.288 4834.514
Min Mz 28078 2104 1.15DL
27062
+ 1.2SIDL
-2950.789
+ 1.4CL -1098.7
+ 1.4PLB + -352.317
1.54TLB - -35.615
1.54BTB -955.807 -3394.528

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 4789.497 3372.254 9575.000 OK
ODE Seismic 8363.084 -1912.475 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -2079 4176 5300 0.788 OK
Minima 45.79 3112 5810 0.536 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 144.9 OK
Minima -309.9 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.866 OK 38.09 OK
Minima 1.085 OK 11.56 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 21.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 29311 1005 1DL28295
+ 1SIDL 4789.497
+ 1CL + 1PLA -13.721
+ 1PLB + 1.1TLA
3.399
+ 1.1TLB
-0.888
+ 1.1BTA-14.392
+ 1.1BTB -46.435
Min Fx 29320 1001 1DL28304
+ 1SIDL 3372.254
+ 1CL + 1PLA +-6.941
1.1TLA + 1.1BTA
0.306 -0.602 2.135 -19.382
Max Fy 29320 1006 1DL28304
+ 1SIDL 4514.154
+ 1CL + 1PLA + 2.767
1PLB + 1.1TLA
-0.974
+ 1.1TLB
-0.722
- 1.1BTA - 1.1BTB
5.936 10.377
Min Fy 29311 1005 1DL28295
+ 1SIDL 4789.497
+ 1CL + 1PLA -13.721
+ 1PLB + 1.1TLA
3.399
+ 1.1TLB
-0.888
+ 1.1BTA-14.392
+ 1.1BTB -46.435
Max Fz 29311 1005 1DL28295
+ 1SIDL 4789.497
+ 1CL + 1PLA -13.721
+ 1PLB + 1.1TLA
3.399
+ 1.1TLB
-0.888
+ 1.1BTA-14.392
+ 1.1BTB -46.435
Min Fz 29320 1006 1DL28304
+ 1SIDL 4514.154
+ 1CL + 1PLA + 2.767
1PLB + 1.1TLA
-0.974
+ 1.1TLB
-0.722
- 1.1BTA - 1.1BTB
5.936 10.377
Max Mx 29329 1004 1DL28313
+ 1SIDL 3862.219
+ 1CL + 1PLB +-3.025
1.1TLB - 1.1BTB
-0.893 -0.183 4.745 -13.307
Min Mx 29311 1002 1DL28295
+ 1SIDL 3867.649
+ 1CL + 1PLA +-3.102
1.1TLA - 1.1BTA
2.063 -1.053 -8.847 -13.549
Max My 29320 1006 1DL28304
+ 1SIDL 4514.154
+ 1CL + 1PLA + 2.767
1PLB + 1.1TLA
-0.974
+ 1.1TLB
-0.722
- 1.1BTA - 1.1BTB
5.936 10.377
Min My 29311 1005 1DL28295
+ 1SIDL 4789.497
+ 1CL + 1PLA -13.721
+ 1PLB + 1.1TLA
3.399
+ 1.1TLB
-0.888
+ 1.1BTA-14.392
+ 1.1BTB -46.435
Max Mz 29320 1006 1DL28304
+ 1SIDL 4514.154
+ 1CL + 1PLA + 2.767
1PLB + 1.1TLA
-0.974
+ 1.1TLB
-0.722
- 1.1BTA - 1.1BTB
5.936 10.377
Min Mz 29311 1005 1DL28295
+ 1SIDL 4789.497
+ 1CL + 1PLA -13.721
+ 1PLB + 1.1TLA
3.399
+ 1.1TLB
-0.888
+ 1.1BTA-14.392
+ 1.1BTB -46.435
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 29329 1095 1DL28313
+ 1SIDL 8363.084
+ 0.3CL + 0.3PLA
16.117
+ 0.3PLB104.151
+ 0.33TLA +9.656
0.33TLB +337.352
0.33BTA + 0.33BTB
48.915 + 0.3SLX + 0.
Min Fx 29329 1015 1DL28314
+ 1SIDL-1662.404
+ 0.3SLX + 0.3SLY
-28.254
+ 1SLZ-105.142 -10.841 -226.025 -64.349
Max Fy 29320 1086 1DL28305
+ 1SIDL 7013.581
+ 0.3CL + 0.3PLA74.66
+ 0.3PLB51.083
+ 0.33TLA 18.333
+ 0.33TLB -116.732
0.33BTA - 0.33BTB
165.525- 1SLX - 0.3SLY
Min Fy 29311 1079 1DL28296
+ 1SIDL +187.612
0.3CL + 0.3PLA
-82.96
+ 0.3PLB-49.712
+ 0.33TLA-21.011
+ 0.33TLB-120.557
+ 0.33BTA +-184.317
0.33BTB + 1SLX + 0.3S
Max Fz 29311 3047 1DL28295
+ 1SIDL 7969.669
+ 0.3CL + 0.3PLA
18.038
+ 0.33TLA
107.162
+ 0.33BTA
10.395
+ 0.3SLX
321.995
+ 0.3SLY +56.051
1SLZ + 1.1NLA
Min Fz 29329 3071 1DL28314
+ 1SIDL-1291.572
+ 0.3CL + 0.3PLB
-29.745
+ 0.33TLB
-105.968
+ 0.33BTB
-11.371
+ 0.3SLX
-224.303
+ 0.3SLY + 1SLZ
-67.71+ 1.1NLB
Max Mx 29311 3062 1DL28296
+ 1SIDL 6765.038
+ 0.3CL + 0.3PLB
71.343
+ 0.33TLB 54.248
- 0.33BTB
20.316
- 1SLX 105.493
- 0.3SLY - 0.3SLZ
153.644
- 1.1NLB
Min Mx 29311 3038 1DL28295
+ 1SIDL + -126.79
0.3CL + 0.3PLA
-79.771
+ 0.33TLA-50.844
- 0.33BTA
-21.576
- 1SLX-170.612
- 0.3SLY - 0.3SLZ
-257.363
- 1.1NLA
Max My 29329 3071 1DL28313
+ 1SIDL 8245.954
+ 0.3CL + 0.3PLB
17.326
+ 0.33TLB
103.131
+ 0.33BTB
9.163
+ 0.3SLX
340.247
+ 0.3SLY + 1SLZ
52.76+ 1.1NLB
Min My 29311 3078 1DL28295
+ 1SIDL-1136.995
+ 0.3CL + 0.3PLB
-28.471
+ 0.33TLB
-101.977
- 0.33BTB
-10.519
- 0.3SLX
-343.209
- 0.3SLY - 1SLZ
-94.583
- 1.1NLB
Max Mz 29320 1007 1DL28304
+ 1SIDL 6529.417
+ 1SLX + 0.3SLY73.06
+ 0.3SLZ 51.205 18.375 168.537 235.123
Min Mz 29311 1014 1DL28295
+ 1SIDL - 1SLX
-314.48
- 0.3SLY
-80.259
- 0.3SLZ -50.258 -20.933 -172.379 -258.555

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 29302 2104 1.15DL
28286
+ 1.2SIDL
11225.737
+ 1.4CL145.854
+ 1.4PLB + 1.54TLB
46.357 - 1.54BTB
35.78 135.707 467.423
Min Fx 29302 2103 1.15DL
28287
+ 1.2SIDL
-3479.508
+ 1.4CL-153.998
+ 1.4PLB + 1.54TLB
-43.006 + -36.372
1.54BTB -106.025 -334.426
Max Fy 29302 2104 1.15DL
28286
+ 1.2SIDL
11225.737
+ 1.4CL145.854
+ 1.4PLB + 1.54TLB
46.357 - 1.54BTB
35.78 135.707 467.423
Min Fy 29329 2103 1.15DL
28314
+ 1.2SIDL
-2219.465
+ 1.4CL-156.798
+ 1.4PLB + 1.54TLB
-45.844 + -35.085
1.54BTB -93.345 -345.963
Max Fz 29302 3147 1.15DL
28286
+ 1.2SIDL
9773.19
+ 0.42CL24.819
+ 0.42PLA 134.706
+ 0.462TLA12.653
+ 0.462BTA
405.779
+ 0.3SLX 81.684
+ 0.3SLY + 1SLZ + 1.5
Min Fz 29329 3171 1.15DL
28314
+ 1.2SIDL
-1871.609
+ 0.42CL-37.076
+ 0.42PLB-133.083
+ 0.462TLB -14.285
+ 0.462BTB
-281.561
+ 0.3SLX +-84.17
0.3SLY + 1SLZ + 1.5
Max Mx 29311 2104 1.15DL
28295
+ 1.2SIDL
8388.827
+ 1.4CL +142.39
1.4PLB + 1.54TLB
45.065 - 1.54BTB
36.44 129.661 449.717
Min Mx 29311 2103 1.15DL
28296
+ 1.2SIDL45.79
+ 1.4CL-156.452
+ 1.4PLB + 1.54TLB
-41.627 + -37.025
1.54BTB -101.515 -344.563
Max My 29329 3171 1.15DL
28313
+ 1.2SIDL
10102.916
+ 0.42CL22.006
+ 0.42PLB 129.389
+ 0.462TLB 11.482
+ 0.462BTB
427.058
+ 0.3SLX + 67.23
0.3SLY + 1SLZ + 1.5
Min My 29302 3178 1.15DL
28286
+ 1.2SIDL
-2256.671
+ 0.42CL-31.516
+ 0.42PLB-128.278
+ 0.462TLB -12.567
- 0.462BTB
-431.646
- 0.3SLX --98.465
0.3SLY - 1SLZ - 1.54N
Max Mz 29302 2104 1.15DL
28286
+ 1.2SIDL
11225.737
+ 1.4CL145.854
+ 1.4PLB + 1.54TLB
46.357 - 1.54BTB
35.78 135.707 467.423
Min Mz 29329 1452 1.15DL
28313
+ 1.2SIDL
7523.451
- 1.5COL(-X)-MLC
-114.512 -4.059 -3.417 16.235 -370.896

ODE MDE
Maximum Tension Force (kN) -1662.40 -3479.51
Skin Friction (kN) 3631.33
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 442.7 885.8 0.500 OK
Minima 9773 413.9 2997 0.138 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 62.62 OK
Minima -82.26 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.411 OK 31.1 OK
Minima 2.798 OK 20.15 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.954 m
Hence de = 0.904 m and dv = 0.813 m
Horizontal resultant shear force at the section, Vu = 1232 kN
Corresponding axial compressive force, N = 11183 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 40212 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0201 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 2.060 %
Horizontal shear force, Vu = 1232 kN
Shear stress (vv = Vu /(bv . dv) = 1261.88 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.940 Mpa
= 940 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 832.311 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.49
Modified shear strength of concrete (n s vc ) = 1243.79 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 17.66 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.38 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 15.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28117 1005 1DL27100
+ 1SIDL 4789.497
+ 1CL + 1PLA -14.532
+ 1PLB + 1.1TLA
1.434
+ 1.1TLB
-0.888
+ 1.1BTA-31.442
+ 1.1BTB -142.569
Min Fx 28135 1001 1DL27118
+ 1SIDL 3372.254
+ 1CL + 1PLA -10.428
+ 1.1TLA + 1.1BTA
2.698 -0.602 -7.422 -77.622
Max Fy 28153 1006 1DL27136
+ 1SIDL 4073.679
+ 1CL + 1PLA + 2.944
1PLB + 1.1TLA
0.921
+ 1.1TLB
-0.711
- 1.1BTA - 1.1BTB
5.744 1.459
Min Fy 28135 1005 1DL27118
+ 1SIDL 3716.364
+ 1CL + 1PLA -15.297
+ 1PLB + 1.1TLA
2.199
+ 1.1TLB
-0.728
+ 1.1BTA +-5.791
1.1BTB -116.919
Max Fz 28153 1001 1DL27136
+ 1SIDL 4026.568
+ 1CL + 1PLA +-9.761
1.1TLA + 1.1BTA
2.718 -0.577 -6.608 -99.988
Min Fz 28099 1004 1DL27082
+ 1SIDL 3799.384
+ 1CL + 1PLB +-1.585
1.1TLB - 1.1BTB
-0.335 -0.218 -15.871 -4.483
Max Mx 28153 1004 1DL27136
+ 1SIDL 3862.219
+ 1CL + 1PLB +-0.904
1.1TLB - 1.1BTB
0.346 -0.183 6.965 -27.319
Min Mx 28099 1002 1DL27082
+ 1SIDL 3942.867
+ 1CL + 1PLA +-1.687
1.1TLA - 1.1BTA
0.778 -1.062 -19.202 -5.038
Max My 28135 1004 1DL27119
+ 1SIDL 3942.465
+ 1CL + 1PLB +-1.595
1.1TLB - 1.1BTB
0.355 -0.192 7.592 -2.557
Min My 28117 1005 1DL27100
+ 1SIDL 4789.497
+ 1CL + 1PLA -14.532
+ 1PLB + 1.1TLA
1.434
+ 1.1TLB
-0.888
+ 1.1BTA-31.442
+ 1.1BTB -142.569
Max Mz 28135 1006 1DL27118
+ 1SIDL 4514.154
+ 1CL + 1PLA + 2.171
1PLB + 1.1TLA
0.946
+ 1.1TLB
-0.722
- 1.1BTA - 1.1BTB
6.584 27.39
Min Mz 28117 1005 1DL27100
+ 1SIDL 4789.497
+ 1CL + 1PLA -14.532
+ 1PLB + 1.1TLA
1.434
+ 1.1TLB
-0.888
+ 1.1BTA-31.442
+ 1.1BTB -142.569

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28153 1095 1DL27136
+ 1SIDL 8363.084
+ 0.3CL + 0.3PLA
21.664
+ 0.3PLB126.946
+ 0.33TLA +9.656
0.33TLB1114.326
+ 0.33BTA + 175.377
0.33BTB + 0.3SLX + 0.
Min Fx 28099 1015 1DL27083
+ 1SIDL-1912.475
+ 0.3SLX + 0.3SLY
-33.15
+ 1SLZ-125.493 -10.773 -1000.992 -247.983
Max Fy 28153 1086 1DL27137
+ 1SIDL +7991.94
0.3CL + 0.3PLA89.18
+ 0.3PLB63.347
+ 0.33TLA 18.772
+ 0.33TLB -499.713
0.33BTA - 0.33BTB
682.322- 1SLX - 0.3SLY
Min Fy 28099 1079 1DL27083
+ 1SIDL-1620.778
+ 0.3CL + 0.3PLA
-98.676
+ 0.3PLB-61.909
+ 0.33TLA-20.596
+ 0.33TLB-513.147
+ 0.33BTA +-761.854
0.33BTB + 1SLX + 0.3S
Max Fz 28135 3047 1DL27118
+ 1SIDL 7537.213
+ 0.3CL + 0.3PLA
22.379
+ 0.33TLA
128.069
+ 0.33BTA
9.784
+ 0.3SLX
1103.893
+ 0.3SLY 213.364
+ 1SLZ + 1.1NLA
Min Fz 28117 3071 1DL27101
+ 1SIDL-1107.771
+ 0.3CL + 0.3PLB
-34.217
+ 0.33TLB
-126.645
+ 0.33BTB
-11.714
+ 0.3SLX
-993.652
+ 0.3SLY +-285.66
1SLZ + 1.1NLB
Max Mx 28117 3062 1DL27101
+ 1SIDL 6765.038
+ 0.3CL + 0.3PLB
88.015
+ 0.33TLB 63.669
- 0.33BTB
20.316
- 1SLX 468.535
- 0.3SLY - 0.3SLZ
675.472
- 1.1NLB
Min Mx 28117 3038 1DL27100
+ 1SIDL + -126.79
0.3CL + 0.3PLA
-94.038
+ 0.33TLA-63.192
- 0.33BTA
-21.576
- 1SLX-559.921
- 0.3SLY - 0.3SLZ
-845.802
- 1.1NLA
Max My 28153 3071 1DL27136
+ 1SIDL 8245.954
+ 0.3CL + 0.3PLB23.13
+ 0.33TLB
125.447
+ 0.33BTB
9.163
+ 0.3SLX
1125.677
+ 0.3SLY +188.273
1SLZ + 1.1NLB
Min My 28099 3078 1DL27082
+ 1SIDL-1606.902
+ 0.3CL + 0.3PLB
-32.297
+ 0.33TLB
-124.717
- 0.33BTB
-10.142
- 0.3SLX
-1135.519
- 0.3SLY - -273.322
1SLZ - 1.1NLB
Max Mz 28135 1007 1DL27118
+ 1SIDL 6529.417
+ 1SLX + 0.3SLY86.577
+ 0.3SLZ 63.422 18.375 555.417 775.444
Min Mz 28117 1014 1DL27100
+ 1SIDL - 1SLX
-314.48
- 0.3SLY
-94.898
- 0.3SLZ -62.407 -20.933 -566.311 -851.487
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28099 2104 1.15DL
27082
+ 1.2SIDL
11225.737
+ 1.4CL +174.23
1.4PLB + 1.54TLB
52.311 - 1.54BTB
35.78 459.503 1550.637
Min Fx 28099 2103 1.15DL
27083
+ 1.2SIDL
-3479.508
+ 1.4CL-187.794
+ 1.4PLB + 1.54TLB
-52.726 + -36.372
1.54BTB -434.857 -1456.373
Max Fy 28117 2104 1.15DL
27100
+ 1.2SIDL
8388.827
+ 1.4CL175.047
+ 1.4PLB + 1.54TLB
52.569 - 1.54BTB
36.44 449.798 1522.661
Min Fy 28135 2103 1.15DL
27119
+ 1.2SIDL
-1169.208
+ 1.4CL-187.861
+ 1.4PLB + 1.54TLB
-52.317 + 1.54BTB
-34.43 -400.1 -1453.488
Max Fz 28135 3147 1.15DL
27118
+ 1.2SIDL
9195.754
+ 0.42CL28.302
+ 0.42PLA 160.935
+ 0.462TLA12.411
+ 0.462BTA
1383.816
+ 0.3SLX268.863
+ 0.3SLY + 1SLZ + 1.5
Min Fz 28117 3171 1.15DL
27101
+ 1.2SIDL
-1659.201
+ 0.42CL -42.82
+ 0.42PLB +-159.19
0.462TLB
-14.712
+ 0.462BTB
-1245.093
+ 0.3SLX-356.228
+ 0.3SLY + 1SLZ + 1.5
Max Mx 28117 2104 1.15DL
27100
+ 1.2SIDL
8388.827
+ 1.4CL175.047
+ 1.4PLB + 1.54TLB
52.569 - 1.54BTB
36.44 449.798 1522.661
Min Mx 28117 2103 1.15DL
27101
+ 1.2SIDL45.79
+ 1.4CL-187.188
+ 1.4PLB + 1.54TLB
-52.999 + -37.025
1.54BTB -425.633 -1476.741
Max My 28153 3171 1.15DL
27136
+ 1.2SIDL
10102.916
+ 0.42CL29.205
+ 0.42PLB 157.267
+ 0.462TLB 11.482
+ 0.462BTB
1414.05
+ 0.3SLX238.835
+ 0.3SLY + 1SLZ + 1.5
Min My 28099 3178 1.15DL
27082
+ 1.2SIDL
-2256.671
+ 0.42CL-39.986
+ 0.42PLB-156.498
+ 0.462TLB -12.567
- 0.462BTB
-1425.309
- 0.3SLX-338.912
- 0.3SLY - 1SLZ - 1.54N
Max Mz 28099 2104 1.15DL
27082
+ 1.2SIDL
11225.737
+ 1.4CL +174.23
1.4PLB + 1.54TLB
52.311 - 1.54BTB
35.78 459.503 1550.637
Min Mz 28153 2103 1.15DL
27137
+ 1.2SIDL
-2219.465
+ 1.4CL-187.121
+ 1.4PLB + 1.54TLB
-52.043 + -35.085
1.54BTB -409.301 -1479.629

ODE MDE
Maximum Tension Force (kN) -1912.48 -3479.51
Skin Friction (kN) 2584.00
Final Axial Load (kN) 0.00 -895.51

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


40 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -895.5 1520 2933 0.518 OK
Minima 9196 1410 4556 0.309 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 80.27 OK
Minima -155 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 0.000 N/mm2


Steel 0.75fy 0.000 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.579 OK 31.5 OK
Minima 2.281 OK 16.94 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C19, C21 & C23


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C19, C21, C23

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25800 1003 1DL24670
+ 1SIDL +4157.118
1CL + 1PLB + 0.179
1.1TLB + 1.1BTB
0.785 -0.496 3.43 -60.283
Min Fx 25833 1001 1DL24703
+ 1SIDL +3468.241
1CL + 1PLA + 6.063
1.1TLA + 1.1BTA
-2.929 0.237 -16.416 -51.592
Max Fy 25796 1005 1DL24636
+ 1SIDL +3949.919
1CL + 1PLA +34.229
1PLB + 1.1TLA
-3.621
+ 1.1TLB-0.367
+ 1.1BTA + 1.1BTB
3.24 6.777
Min Fy 25829 1006 1DL24669
+ 1SIDL +4142.218
1CL + 1PLA -27.966
+ 1PLB + 1.1TLA
-0.571
+ 1.1TLB-0.258
- 1.1BTA - 1.1BTB
0.051 -59.744
Max Fz 25829 1004 1DL24669
+ 1SIDL +4151.417
1CL + 1PLB +-15.578
1.1TLB - 1.1BTB
2.807 -0.314 -1.392 -53.557
Min Fz 25796 1001 1DL24636
+ 1SIDL +3949.397
1CL + 1PLA +21.823
1.1TLA + 1.1BTA
-8.388 -0.228 4.83 2.244
Max Mx 25833 1001 1DL24703
+ 1SIDL +3468.241
1CL + 1PLA + 6.063
1.1TLA + 1.1BTA
-2.929 0.237 -16.416 -51.592
Min Mx 25800 1003 1DL24670
+ 1SIDL +4157.118
1CL + 1PLB + 0.179
1.1TLB + 1.1BTB
0.785 -0.496 3.43 -60.283
Max My 25769 1004 1DL24640
+ 1SIDL +3927.273
1CL + 1PLB + -1.274
1.1TLB - 1.1BTB
0.045 -0.161 8.676 4.251
Min My 25835 1001 1DL24706
+ 1SIDL +3468.241
1CL + 1PLA + 0.595
1.1TLA + 1.1BTA
-0.744 0.237 -21.806 -61.265
Max Mz 25806 1006 1DL24677
+ 1SIDL +4142.218
1CL + 1PLA +-0.199
1PLB + 1.1TLA
0.101
+ 1.1TLB-0.258
- 1.1BTA - 1.1BTB
-1.349 48.303
Min Mz 25835 1005 1DL24706
+ 1SIDL +3493.401
1CL + 1PLA + 1PLB
1.912+ 1.1TLA
-0.806
+ 1.1TLB-0.034
+ 1.1BTA + -12.73
1.1BTB -93.521

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25800 1003 1DL24670
+ 1SIDL +4157.118
1CL + 1PLB + 0.179
1.1TLB + 1.1BTB
0.785 -0.496 3.43 -60.283
Min Fx 25767 1023 1DL24638
+ 1SIDL +1834.276
0.3SLX + 1SLY
-24.349
+ 0.3SLZ -35.58 -3.501 -226.431 -165.449
Max Fy 25862 1152 1DL24702
+ 1SIDL -2463.499
1COL(-X)-MLC
377.531 -9.794 -1.928 21.504 828.453
Min Fy 25829 1086 1DL24669
+ 1SIDL +2871.153
0.3CL + 0.3PLA
-231.14
+ 0.3PLB
-111.759
+ 0.33TLA +-8.894
0.33TLB - 0.33BTA
-31.241 - 0.33BTB
-160.32 - 1SLX - 0.3SLY
Max Fz 25796 3071 1DL24636
+ 1SIDL +2735.691
0.3CL + 0.3PLB
82.609
+ 0.33TLB
278.772
+ 0.33BTB
4.173
+ 0.3SLX80.618
+ 0.3SLY + 1SLZ
44.093
+ 1.1NLB
Min Fz 25796 3047 1DL24667
+ 1SIDL + 2539.88
0.3CL + 0.3PLA
-59.318
+ 0.33TLA
-283.307
+ 0.33BTA
-4.731
+ 0.3SLX
-208.124
+ 0.3SLY + -43.595
1SLZ + 1.1NLA
Max Mx 25767 3062 1DL24638
+ 1SIDL +2791.448
0.3CL + 0.3PLB
86.245
+ 0.33TLB 45.451
- 0.33BTB
8.969
- 1SLX - 0.3SLY
301.83- 0.3SLZ
463.049
- 1.1NLB
Min Mx 25767 3038 1DL24637
+ 1SIDL +2471.012
0.3CL + 0.3PLA
-84.098
+ 0.33TLA-47.212
- 0.33BTA
-9.513
- 1SLX - -258.59
0.3SLY - 0.3SLZ
-403.568
- 1.1NLA
Max My 25770 3071 1DL24640
+ 1SIDL +2735.691
0.3CL + 0.3PLB1.725
+ 0.33TLB 1.586
+ 0.33BTB
4.173
+ 0.3SLX
745.934
+ 0.3SLY + 141.197
1SLZ + 1.1NLB
Min My 25769 3047 1DL24640
+ 1SIDL + 2539.88
0.3CL + 0.3PLA
-7.595
+ 0.33TLA-25.564
+ 0.33BTA
-4.731
+ 0.3SLX
-753.731
+ 0.3SLY +-206.725
1SLZ + 1.1NLA
Max Mz 25796 1152 1DL24636
+ 1SIDL -2105.828
1COL(-X)-MLC
377.441 1.593 -1.399 3.77 828.87
Min Mz 25839 1152 1DL24710
+ 1SIDL -2463.499
1COL(-X)-MLC4.652 -0.122 -1.928 -16.735 -645.246
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25800 2101 1.15DL
24670
+ 1.2SIDL
5203.97
+ 1.4CL + 1.4PLA
0.805 + 1.54TLA
-3.629 + 1.54BTA
0.124 -21.81 -78.985
Min Fx 25767 2123 1.15DL
24638
+ 1.2SIDL
2102.021
+ 0.3SLX-30.773
+ 1SLY + 0.3SLZ
-44.484 -4.364 -283.993 -205.757
Max Fy 25796 1452 1.15DL
24636
+ 1.2SIDL
2434.132
- 1.5COL(-X)-MLC
563.607 3.077 -2.004 4.229 1243.342
Min Fy 25829 2104 1.15DL
24700
+ 1.2SIDL
5088.438
+ 1.4CL-450.421
+ 1.4PLB + 1.54TLB
-61.123 - 1.54BTB
-15.535 -44.623 -243.65
Max Fz 25796 3171 1.15DL
24636
+ 1.2SIDL
3293.232
+ 0.42CL103.624
+ 0.42PLB +350.711
0.462TLB 5.231
+ 0.462BTB
100.333
+ 0.3SLX + 55.285
0.3SLY + 1SLZ + 1.54
Min Fz 25796 3147 1.15DL
24667
+ 1.2SIDL
3058.491
+ 0.42CL-74.659
+ 0.42PLA -356.079
+ 0.462TLA +-5.877
0.462BTA
-261.915
+ 0.3SLX +-54.309
0.3SLY + 1SLZ + 1.54
Max Mx 25767 2104 1.15DL
24637
+ 1.2SIDL
5106.658
+ 1.4CL 160.085
+ 1.4PLB + 1.54TLB
35.357 - 1.54BTB
16.046 194.399 755.962
Min Mx 25767 2103 1.15DL
24638
+ 1.2SIDL
4774.155
+ 1.4CL-153.536
+ 1.4PLB + 1.54TLB
-35.868 + -16.455
1.54BTB -229.123 -986.385
Max My 25770 3171 1.15DL
24640
+ 1.2SIDL
3293.232
+ 0.42CL +2.156
0.42PLB + 1.965
0.462TLB 5.231
+ 0.462BTB938.29
+ 0.3SLX + 177.97
0.3SLY + 1SLZ + 1.54
Min My 25769 3147 1.15DL
24640
+ 1.2SIDL
3058.491
+ 0.42CL +-9.522
0.42PLA +-32.066
0.462TLA +-5.877
0.462BTA
-947.781
+ 0.3SLX-259.272
+ 0.3SLY + 1SLZ + 1.54
Max Mz 25796 1452 1.15DL
24636
+ 1.2SIDL
2434.132
- 1.5COL(-X)-MLC
563.607 3.077 -2.004 4.229 1243.342
Min Mz 25770 2103 1.15DL
24641
+ 1.2SIDL
4774.155
+ 1.4CL +-11.311
1.4PLB + 1.54TLB
-0.986 + -16.455
1.54BTB -260.206 -1155.848

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 4157.118 3468.241 7790.000 OK
ODE Seismic 4157.118 1834.276 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 2434 1243 1379 0.902 OK
Minima 5204 81.95 1775 0.046 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 80.31 OK
Minima -95.19 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.704 OK 39.7 OK
Minima 3.369 OK 25.7 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 16.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25813 1003 1DL24683
+ 1SIDL +4157.118
1CL + 1PLB + -3.093
1.1TLB + 1.1BTB
-0.447 -0.496 1.385 -6.108
Min Fx 25846 1001 1DL24716
+ 1SIDL +3468.241
1CL + 1PLA +-4.715
1.1TLA + 1.1BTA
1.85 0.237 -5.519 -13.14
Max Fy 25813 1006 1DL24683
+ 1SIDL +4142.218
1CL + 1PLA + 1PLB
5.193+ 1.1TLA
0.131
+ 1.1TLB-0.258
- 1.1BTA - 1.1BTB
-0.383 19.049
Min Fy 25780 1005 1DL24650
+ 1SIDL +3949.919
1CL + 1PLA +-7.779
1PLB + 1.1TLA
0.769
+ 1.1TLB-0.367
+ 1.1BTA + -2.444
1.1BTB -22.988
Max Fz 25846 1001 1DL24716
+ 1SIDL +3468.241
1CL + 1PLA +-4.715
1.1TLA + 1.1BTA
1.85 0.237 -5.519 -13.14
Min Fz 25780 1004 1DL24650
+ 1SIDL +3927.273
1CL + 1PLB + 0.725
1.1TLB - 1.1BTB
-0.655 -0.161 1.799 2.86
Max Mx 25846 1001 1DL24716
+ 1SIDL +3468.241
1CL + 1PLA +-4.715
1.1TLA + 1.1BTA
1.85 0.237 -5.519 -13.14
Min Mx 25813 1003 1DL24683
+ 1SIDL +4157.118
1CL + 1PLB + -3.093
1.1TLB + 1.1BTB
-0.447 -0.496 1.385 -6.108
Max My 25813 1004 1DL24683
+ 1SIDL +4151.417
1CL + 1PLB + 2.458
1.1TLB - 1.1BTB
-0.62 -0.314 1.889 10.711
Min My 25780 1001 1DL24650
+ 1SIDL +3949.397
1CL + 1PLA +-5.004
1.1TLA + 1.1BTA
1.838 -0.228 -5.649 -14.646
Max Mz 25813 1006 1DL24683
+ 1SIDL +4142.218
1CL + 1PLA + 1PLB
5.193+ 1.1TLA
0.131
+ 1.1TLB-0.258
- 1.1BTA - 1.1BTB
-0.383 19.049
Min Mz 25780 1005 1DL24650
+ 1SIDL +3949.919
1CL + 1PLA +-7.779
1PLB + 1.1TLA
0.769
+ 1.1TLB-0.367
+ 1.1BTA + -2.444
1.1BTB -22.988

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25813 1003 1DL24683
+ 1SIDL +4157.118
1CL + 1PLB + -3.093
1.1TLB + 1.1BTB
-0.447 -0.496 1.385 -6.108
Min Fx 25780 1023 1DL24651
+ 1SIDL +1834.276
0.3SLX + 1SLY
-16.892
+ 0.3SLZ -21.056 -3.501 -43.933 -35.173
Max Fy 25813 1086 1DL24684
+ 1SIDL +3071.771
0.3CL + 0.3PLA
50.091
+ 0.3PLB + 25.15
0.33TLA + 0.33TLB
8.44 - 0.33BTA
48.446 - 0.33BTB
105.706 - 1SLX - 0.3SLY
Min Fy 25846 1152 1DL24716
+ 1SIDL -2463.499
1COL(-X)-MLC-69.637 1.806 -1.928 -6.674 -257.264
Max Fz 25780 3047 1DL24650
+ 1SIDL +2735.716
0.3CL + 0.3PLA
12.831
+ 0.33TLA 63.852
+ 0.33BTA4.639
+ 0.3SLX182.348
+ 0.3SLY + 1SLZ
39.988
+ 1.1NLA
Min Fz 25780 3071 1DL24651
+ 1SIDL +2539.855
0.3CL + 0.3PLB
-18.194
+ 0.33TLB-62.966
+ 0.33BTB
-5.196
+ 0.3SLX-123.26
+ 0.3SLY + 1SLZ
-37.422
+ 1.1NLB
Max Mx 25780 3062 1DL24651
+ 1SIDL +2791.448
0.3CL + 0.3PLB
48.419
+ 0.33TLB 29.786
- 0.33BTB
8.969
- 1SLX - 0.3SLY
56.942- 0.3SLZ
100.979
- 1.1NLB
Min Mx 25780 3038 1DL24650
+ 1SIDL +2471.012
0.3CL + 0.3PLA
-50.374
+ 0.33TLA-29.099
- 0.33BTA
-9.513
- 1SLX - -88.146
0.3SLY - 0.3SLZ
-154.601
- 1.1NLA
Max My 25780 3071 1DL24650
+ 1SIDL +2735.691
0.3CL + 0.3PLB
12.834
+ 0.33TLB 62.168
+ 0.33BTB
4.173
+ 0.3SLX
187.313
+ 0.3SLY + 1SLZ
39.994
+ 1.1NLB
Min My 25780 1054 1DL24650
+ 1SIDL +2533.308
0.3CL + 0.3PLA
-16.498
+ 0.33TLA-61.941
- 0.33BTA
-4.992
- 0.3SLX-188.467
- 0.3SLY - 1SLZ
-50.424
Max Mz 25813 1007 1DL24683
+ 1SIDL +2570.019
1SLX + 0.3SLY48.347
+ 0.3SLZ 25.242 8.454 72.592 150.073
Min Mz 25846 1152 1DL24716
+ 1SIDL -2463.499
1COL(-X)-MLC-69.637 1.806 -1.928 -6.674 -257.264
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25813 2101 1.15DL
24683
+ 1.2SIDL
5203.97
+ 1.4CL + -4.252
1.4PLA + 1.54TLA
2.366 + 1.54BTA
0.124 -6.982 -8.768
Min Fx 25780 2123 1.15DL
24651
+ 1.2SIDL
2102.021
+ 0.3SLX-21.034
+ 1SLY + 0.3SLZ
-26.461 -4.364 -54.986 -43.797
Max Fy 25813 2104 1.15DL
24683
+ 1.2SIDL
5189.366
+ 1.4CL +97.811
1.4PLB + 1.54TLB
13.786 - 1.54BTB
15.16 41.488 303.55
Min Fy 25780 1452 1.15DL
24650
+ 1.2SIDL
2434.132
- 1.5COL(-X)-MLC
-103.818 -0.803 -2.004 2.043 -384.096
Max Fz 25780 3147 1.15DL
24650
+ 1.2SIDL
3293.268
+ 0.42CL 16.158
+ 0.42PLA + 80.269
0.462TLA +5.883
0.462BTA +228.7
0.3SLX +50.327
0.3SLY + 1SLZ + 1.54
Min Fz 25780 3171 1.15DL
24651
+ 1.2SIDL
3058.456
+ 0.42CL-22.822
+ 0.42PLB +-79.211
0.462TLB-6.528
+ 0.462BTB
-154.433
+ 0.3SLX +-46.943
0.3SLY + 1SLZ + 1.54
Max Mx 25780 2104 1.15DL
24650
+ 1.2SIDL
5106.658
+ 1.4CL +96.409
1.4PLB + 1.54TLB
22.177 - 1.54BTB
16.046 66.239 297.123
Min Mx 25780 2103 1.15DL
24651
+ 1.2SIDL
4774.155
+ 1.4CL-101.567
+ 1.4PLB + 1.54TLB
-22.054 + -16.455
1.54BTB -44.56 -209.877
Max My 25780 3171 1.15DL
24650
+ 1.2SIDL
3293.232
+ 0.42CL 16.162
+ 0.42PLB + 77.911
0.462TLB 5.231
+ 0.462BTB
235.651
+ 0.3SLX + 50.336
0.3SLY + 1SLZ + 1.54
Min My 25780 2154 1.15DL
24650
+ 1.2SIDL
3049.289
+ 0.42CL-20.447
+ 0.42PLA +-77.776
0.462TLA --6.243
0.462BTA
-236.599
- 0.3SLX - -62.496
0.3SLY - 1SLZ
Max Mz 25813 2104 1.15DL
24683
+ 1.2SIDL
5189.366
+ 1.4CL +97.811
1.4PLB + 1.54TLB
13.786 - 1.54BTB
15.16 41.488 303.55
Min Mz 25780 1452 1.15DL
24650
+ 1.2SIDL
2434.132
- 1.5COL(-X)-MLC
-103.818 -0.803 -2.004 2.043 -384.096

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 2434 384.1 1239 0.310 OK
Minima 5204 11.25 1664 0.007 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 37.21 OK
Minima 8.044 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.334 OK 37.77 OK
Minima 4.166 OK 30.01 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.7645 m
Hence de = 0.743 m and dv = 0.669 m
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Horizontal resultant shear force at the section, Vu = 564 kN


Corresponding axial compressive force, N = 2434 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 4536 mm2
Effective area of tensile steel = 50% of total steel = As = 0.0023 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.339 %
Horizontal shear force, Vu = 564 kN
Shear stress (vv = Vu /(bv . dv) = 842.46 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.515 Mpa
= 515 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 478.933 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/Ac) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.15
Modified shear strength of concrete (n s vc ) = 553.15 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 193.55 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.61 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C20 & C22


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C20 & C22

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 4
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30775 1005 1DL29831
+ 1SIDL 5218.422
+ 1CL + 1PLA +111.81
1PLB + 1.1TLA
-27.341
+ 1.1TLB-0.83
+ 1.1BTA181.146
+ 1.1BTB 516.536
Min Fx 30900 1001 1DL29956
+ 1SIDL 3595.392
+ 1CL + 1PLA +58.027
1.1TLA + 1.1BTA
7.191 -0.038 -101.582 185.481
Max Fy 30899 1005 1DL29955
+ 1SIDL 5139.809
+ 1CL + 1PLA116.062
+ 1PLB + 1.1TLA
-28.861
+ 1.1TLB
-0.564
+ 1.1BTA184.935
+ 1.1BTB 536.173
Min Fy 30776 1006 1DL29832
+ 1SIDL 4884.015
+ 1CL + 1PLA -29.073
+ 1PLB + 1.1TLA
13.912
+ 1.1TLB
-0.682
- 1.1BTA -122.36
- 1.1BTB -160.145
Max Fz 30776 1002 1DL29832
+ 1SIDL 4093.257
+ 1CL + 1PLA +-2.034
1.1TLA - 15.568
1.1BTA -0.592 -138.192 -50.37
Min Fz 30899 1005 1DL29955
+ 1SIDL 5139.809
+ 1CL + 1PLA116.062
+ 1PLB + 1.1TLA
-28.861
+ 1.1TLB
-0.564
+ 1.1BTA184.935
+ 1.1BTB 536.173
Max Mx 30901 1001 1DL29957
+ 1SIDL 4245.533
+ 1CL + 1PLA +84.621
1.1TLA + 1.1BTA
7.994 -0.025 -108.078 404.115
Min Mx 30774 1003 1DL29830
+ 1SIDL +3773.78
1CL + 1PLB +51.726
1.1TLB + -24.721
1.1BTB -1.06 175.409 153.844
Max My 30899 1003 1DL29955
+ 1SIDL 4338.941
+ 1CL + 1PLB +83.758
1.1TLB + -28.672
1.1BTB -0.701 193.512 400.884
Min My 30776 1002 1DL29832
+ 1SIDL 4093.257
+ 1CL + 1PLA +-2.034
1.1TLA - 15.568
1.1BTA -0.592 -138.192 -50.37
Max Mz 30899 1005 1DL29955
+ 1SIDL 5139.809
+ 1CL + 1PLA116.062
+ 1PLB + 1.1TLA
-28.861
+ 1.1TLB
-0.564
+ 1.1BTA184.935
+ 1.1BTB 536.173
Min Mz 30933 1005 1DL29993
+ 1SIDL 5139.809
+ 1CL + 1PLA + 1PLB
7.28+ 1.1TLA
-5.473
+ 1.1TLB
-0.564
+ 1.1BTA-28.932
+ 1.1BTB -178.416

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30899 1095 1DL29955
+ 1SIDL 8499.962
+ 0.3CL + 0.3PLA
248.328
+ 0.3PLB720.434
+ 0.33TLA +9.918
0.33TLB3132.103
+ 0.33BTA + 1080.83
0.33BTB + 0.3SLX + 0.
Min Fx 30774 1015 1DL29834
+ 1SIDL-1802.721
+ 0.3SLX + 0.3SLY
-161.938
+ 1SLZ-777.127 -10.739 -2236.078 -537.272
Max Fy 30899 1079 1DL29955
+ 1SIDL 7834.487
+ 0.3CL + 0.3PLA
638.852
+ 0.3PLB260.591
+ 0.33TLA 18.151
+ 0.33TLB1271.054
+ 0.33BTA +2646.831
0.33BTB + 1SLX + 0.3S
Min Fy 30776 1086 1DL29832
+ 1SIDL +-248.475
0.3CL + 0.3PLA
-572.426
+ 0.3PLB
-322.986
+ 0.33TLA-19.313
+ 0.33TLB-1404.29
- 0.33BTA -2359.445
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 30777 3054 1DL29837
+ 1SIDL +8163.96
0.3CL + 0.3PLA
212.117
+ 0.33TLA
775.627
- 0.33BTA9.522
- 0.3SLX
2231.497
- 0.3SLY - 1SLZ
707.502
- 1.1NLA
Min Fz 30774 3078 1DL29830
+ 1SIDL-1418.434
+ 0.3CL + 0.3PLB
-167.907
+ 0.33TLB-784.85
- 0.33BTB
-10.318
- 0.3SLX
-2942.551
- 0.3SLY - -723.147
1SLZ - 1.1NLB
Max Mx 30775 3031 1DL29831
+ 1SIDL +7347.75
0.3CL + 0.3PLA
625.301
+ 0.33TLA
309.531
+ 0.33BTA
19.983
+ 1SLX1455.448
+ 0.3SLY +2585.654
0.3SLZ + 1.1NLA
Min Mx 30775 3055 1DL29835
+ 1SIDL +-229.298
0.3CL + 0.3PLB
-526.269
+ 0.33TLB
-343.692
+ 0.33BTB
-21.183
+ 1SLX
-903.554
+ 0.3SLY +-1559.109
0.3SLZ + 1.1NLB
Max My 30774 3047 1DL29830
+ 1SIDL 8007.645
+ 0.3CL + 0.3PLA
206.362
+ 0.33TLA
741.982
+ 0.33BTA
10.071
+ 0.3SLX
3208.58
+ 0.3SLY 798.034
+ 1SLZ + 1.1NLA
Min My 30777 3054 1DL29833
+ 1SIDL-1323.525
+ 0.3CL + 0.3PLA
-145.685
+ 0.33TLA
-749.538
- 0.33BTA
-11.447
- 0.3SLX
-3185.807
- 0.3SLY --541.575
1SLZ - 1.1NLA
Max Mz 30899 1079 1DL29955
+ 1SIDL 7834.487
+ 0.3CL + 0.3PLA
638.852
+ 0.3PLB260.591
+ 0.33TLA 18.151
+ 0.33TLB1271.054
+ 0.33BTA +2646.831
0.33BTB + 1SLX + 0.3S
Min Mz 30900 1086 1DL29956
+ 1SIDL +-339.204
0.3CL + 0.3PLA
-572.401
+ 0.3PLB
-275.516
+ 0.33TLA-17.795
+ 0.33TLB-1207.915
- 0.33BTA -2362.792
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30777 2103 1.15DL
29833
+ 1.2SIDL
11298.346
+ 1.4CL1203.17
+ 1.4PLB + 232.634
1.54TLB + 33.041
1.54BTB 843.356 4932.094
Min Fx 30774 2115 1.15DL
29834
+ 1.2SIDL
-2557.087
+ 0.3SLX
-205.187
+ 0.3SLY +-974.131
1SLZ -13.42 -2815.189 -676.335
Max Fy 30901 2103 1.15DL
29957
+ 1.2SIDL
10608.686
+ 1.4CL
1210.666
+ 1.4PLB + 133.244
1.54TLB + 1.54BTB
30.58 471.493 4964.958
Min Fy 30774 2104 1.15DL
29834
+ 1.2SIDL
-1915.637
+ 1.4CL-1113.52
+ 1.4PLB + -246.066
1.54TLB - -35.614
1.54BTB -574.999 -3438.619
Max Fz 30777 3154 1.15DL
29837
+ 1.2SIDL
9979.461
+ 0.42CL262.175
+ 0.42PLA 974.395
+ 0.462TLA11.947
- 0.462BTA
2801.363
- 0.3SLX 872.068
- 0.3SLY - 1SLZ - 1.54N
Min Fz 30774 3178 1.15DL
29830
+ 1.2SIDL
-2019.086
+ 0.42CL
-213.543
+ 0.42PLB-984.942
+ 0.462TLB-12.831
- 0.462BTB
-3697.539
- 0.3SLX-915.353
- 0.3SLY - 1SLZ - 1.54N
Max Mx 30775 2104 1.15DL
29831
+ 1.2SIDL
9358.045
+ 1.4CL
1124.951
+ 1.4PLB + 194.547
1.54TLB - 1.54BTB
35.392 1000.043 4625.758
Min Mx 30775 2103 1.15DL
29835
+ 1.2SIDL
-98.69
+ 1.4CL-1005.71
+ 1.4PLB + -238.354
1.54TLB + -36.724
1.54BTB -494.025 -2996.857
Max My 30774 3147 1.15DL
29830
+ 1.2SIDL
9807.961
+ 0.42CL258.875
+ 0.42PLA 932.028
+ 0.462TLA12.776
+ 0.462BTA
4020.934
+ 0.3SLX1003.458
+ 0.3SLY + 1SLZ + 1.5
Min My 30777 3154 1.15DL
29833
+ 1.2SIDL
-1930.926
+ 0.42CL
-187.192
+ 0.42PLA-940.287
+ 0.462TLA-14.381
- 0.462BTA
-3999.171
- 0.3SLX-700.274
- 0.3SLY - 1SLZ - 1.54N
Max Mz 30901 2103 1.15DL
29957
+ 1.2SIDL
10608.686
+ 1.4CL
1210.666
+ 1.4PLB + 133.244
1.54TLB + 1.54BTB
30.58 471.493 4964.958
Min Mz 30774 2104 1.15DL
29834
+ 1.2SIDL
-1915.637
+ 1.4CL-1113.52
+ 1.4PLB + -246.066
1.54TLB - -35.614
1.54BTB -574.999 -3438.619

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 5218.422 3595.392 9575.000 OK
ODE Seismic 8499.962 -1802.721 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 11300 5004 6453 0.775 OK
Minima 9979 2934 6563 0.447 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 142.3 OK
Minima -298.5 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 6.378 OK 41.34 OK
Minima 1.07 OK 10.96 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 19.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30817 1005 1DL29876
+ 1SIDL 5218.422
+ 1CL + 1PLA -17.206
+ 1PLB + 1.1TLA
3.388
+ 1.1TLB-0.83
+ 1.1BTA-20.816
+ 1.1BTB -82.825
Min Fx 30959 1001 1DL30018
+ 1SIDL 3595.392
+ 1CL + 1PLA -10.163
+ 1.1TLA + -0.085
1.1BTA -0.038 6.029 -42.137
Max Fy 30835 1006 1DL29894
+ 1SIDL 4884.015
+ 1CL + 1PLA + 4.088
1PLB + 1.1TLA
-1.273
+ 1.1TLB
-0.682
- 1.1BTA -10.901
1.1BTB 21.801
Min Fy 30941 1005 1DL30000
+ 1SIDL 5139.809
+ 1CL + 1PLA +-17.86
1PLB + 1.1TLA3.67
+ 1.1TLB
-0.564
+ 1.1BTA-21.909
+ 1.1BTB -85.974
Max Fz 30941 1005 1DL30000
+ 1SIDL 5139.809
+ 1CL + 1PLA +-17.86
1PLB + 1.1TLA3.67
+ 1.1TLB
-0.564
+ 1.1BTA-21.909
+ 1.1BTB -85.974
Min Fz 30876 1002 1DL29916
+ 1SIDL 4093.257
+ 1CL + 1PLA + 0.05
1.1TLA - 1.1BTA
-1.676 -0.592 9.208 2.323
Max Mx 30977 1001 1DL30036
+ 1SIDL 4245.533
+ 1CL + 1PLA -12.825
+ 1.1TLA + -0.167
1.1BTA -0.025 6.652 -62.819
Min Mx 30799 1003 1DL29858
+ 1SIDL +3773.78
1CL + 1PLB +-9.232
1.1TLB + 1.1BTB
2.89 -1.06 -18.94 -37.444
Max My 30835 1002 1DL29894
+ 1SIDL 4093.257
+ 1CL + 1PLA +-0.299
1.1TLA - 1.1BTA
-1.405 -0.592 12.212 1.927
Min My 30941 1005 1DL30000
+ 1SIDL 5139.809
+ 1CL + 1PLA +-17.86
1PLB + 1.1TLA3.67
+ 1.1TLB
-0.564
+ 1.1BTA-21.909
+ 1.1BTB -85.974
Max Mz 30835 1006 1DL29894
+ 1SIDL 4884.015
+ 1CL + 1PLA + 4.088
1PLB + 1.1TLA
-1.273
+ 1.1TLB
-0.682
- 1.1BTA -10.901
1.1BTB 21.801
Min Mz 30941 1005 1DL30000
+ 1SIDL 5139.809
+ 1CL + 1PLA +-17.86
1PLB + 1.1TLA3.67
+ 1.1TLB
-0.564
+ 1.1BTA-21.909
+ 1.1BTB -85.974
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30941 1095 1DL30000
+ 1SIDL 8499.962
+ 0.3CL + 0.3PLA
20.717
+ 0.3PLB123.151
+ 0.33TLA +9.918
0.33TLB +528.831
0.33BTA + 0.33BTB
91.075 + 0.3SLX + 0.
Min Fx 30799 1015 1DL29859
+ 1SIDL-1802.721
+ 0.3SLX + 0.3SLY
-32.44
+ 1SLZ -122.21 -10.739 -445.845 -111.187
Max Fy 30835 1086 1DL29895
+ 1SIDL 7243.106
+ 0.3CL + 0.3PLA
92.359
+ 0.3PLB53.337
+ 0.33TLA 18.167
+ 0.33TLB - 0.33BTA
194.44 - 0.33BTB
328.751- 1SLX - 0.3SLY
Min Fy 30941 1079 1DL30001
+ 1SIDL + -27.778
0.3CL + 0.3PLA
-102.87
+ 0.3PLB-43.218
+ 0.33TLA-19.064
+ 0.33TLB-174.348
+ 0.33BTA +-367.245
0.33BTB + 1SLX + 0.3S
Max Fz 30799 3078 1DL29859
+ 1SIDL 8057.561
+ 0.3CL + 0.3PLB
26.786
+ 0.33TLB
126.758
- 0.33BTB
9.996
- 0.3SLX
422.532
- 0.3SLY - 1SLZ
97.047
- 1.1NLB
Min Fz 30853 3054 1DL29912
+ 1SIDL-1323.525
+ 0.3CL + 0.3PLA
-33.739
+ 0.33TLA
-125.302
- 0.33BTA
-11.447
- 0.3SLX
-550.284
- 0.3SLY --156.408
1SLZ - 1.1NLA
Max Mx 30817 3031 1DL29876
+ 1SIDL +7347.75
0.3CL + 0.3PLA
86.114
+ 0.33TLA56.673
+ 0.33BTA
19.983
+ 1SLX226.927
+ 0.3SLY + 385.963
0.3SLZ + 1.1NLA
Min Mx 30817 3055 1DL29877
+ 1SIDL +-229.298
0.3CL + 0.3PLB
-100.711
+ 0.33TLB -52.56
+ 0.33BTB
-21.183
+ 1SLX
-197.834
+ 0.3SLY + -359.059
0.3SLZ + 1.1NLB
Max My 30853 3071 1DL29912
+ 1SIDL 8314.165
+ 0.3CL + 0.3PLB
21.853
+ 0.33TLB
122.992
+ 0.33BTB9.43
+ 0.3SLX
567.692
+ 0.3SLY + 94.577
1SLZ + 1.1NLB
Min My 30799 3078 1DL29858
+ 1SIDL-1418.434
+ 0.3CL + 0.3PLB-31.5
+ 0.33TLB
-121.111
- 0.33BTB
-10.318
- 0.3SLX
-577.281
- 0.3SLY - -139.148
1SLZ - 1.1NLB
Max Mz 30959 1007 1DL30018
+ 1SIDL +7038.72
1SLX + 0.3SLY
90.165
+ 0.3SLZ 45.905 17.027 209.892 411.432
Min Mz 30941 1014 1DL30000
+ 1SIDL --557.687
1SLX - 0.3SLY
-99.181
- 0.3SLZ -43.669 -19.018 -220.245 -453.017

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30853 2103 1.15DL
29912
+ 1.2SIDL
11298.346
+ 1.4CL164.586
+ 1.4PLB + 1.54TLB
35.917 + 33.041
1.54BTB 171.771 739.846
Min Fx 30799 2115 1.15DL
29859
+ 1.2SIDL
-2557.087
+ 0.3SLX-40.398
+ 0.3SLY +-153.604
1SLZ -13.42 -558.752 -138.691
Max Fy 30799 2104 1.15DL
29858
+ 1.2SIDL
10962.077
+ 1.4CL180.215
+ 1.4PLB + 1.54TLB
38.636 - 1.54BTB
34.964 149.618 818.773
Min Fy 30977 2103 1.15DL
30037
+ 1.2SIDL
-1265.006
+ 1.4CL-195.696
+ 1.4PLB + 1.54TLB
-20.607 + -31.555
1.54BTB -71.322 -694.678
Max Fz 30799 3178 1.15DL
29859
+ 1.2SIDL
9877.842
+ 0.42CL34.128
+ 0.42PLB +159.12
0.462TLB12.673
- 0.462BTB
530.691
- 0.3SLX 123.318
- 0.3SLY - 1SLZ - 1.54N
Min Fz 30853 3154 1.15DL
29912
+ 1.2SIDL
-1930.926
+ 0.42CL -41.74
+ 0.42PLA-157.457
+ 0.462TLA-14.381
- 0.462BTA
-690.345
- 0.3SLX-193.292
- 0.3SLY - 1SLZ - 1.54N
Max Mx 30817 2104 1.15DL
29876
+ 1.2SIDL
9358.045
+ 1.4CL +177.05
1.4PLB + 1.54TLB
37.569 - 1.54BTB
35.392 142.073 794.212
Min Mx 30817 2103 1.15DL
29877
+ 1.2SIDL
-98.69
+ 1.4CL-194.316
+ 1.4PLB + 1.54TLB
-32.501 + -36.724
1.54BTB -137.696 -688.976
Max My 30853 3171 1.15DL
29912
+ 1.2SIDL
10189.748
+ 0.42CL27.698
+ 0.42PLB 154.326
+ 0.462TLB 11.817
+ 0.462BTB
712.743
+ 0.3SLX120.199
+ 0.3SLY + 1SLZ + 1.5
Min My 30799 3178 1.15DL
29858
+ 1.2SIDL
-2019.086
+ 0.42CL-39.082
+ 0.42PLB-152.065
+ 0.462TLB-12.831
- 0.462BTB
-724.424
- 0.3SLX-172.829
- 0.3SLY - 1SLZ - 1.54N
Max Mz 30799 2104 1.15DL
29858
+ 1.2SIDL
10962.077
+ 1.4CL180.215
+ 1.4PLB + 1.54TLB
38.636 - 1.54BTB
34.964 149.618 818.773
Min Mz 30977 2103 1.15DL
30037
+ 1.2SIDL
-1265.006
+ 1.4CL-195.696
+ 1.4PLB + 1.54TLB
-20.607 + -31.555
1.54BTB -71.322 -694.678

ODE MDE
Maximum Tension Force (kN) -1802.72 -2557.09
Skin Friction (kN) 2904.67
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 744.8 885.6 0.841 OK
Minima 9878 544.8 2996 0.182 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 69.95 OK
Minima -221.1 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.992 OK 34.94 OK
Minima 2.859 OK 20.78 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.954 m
Hence de = 0.904 m and dv = 0.813 m
Horizontal resultant shear force at the section, Vu = 1225 kN
Corresponding axial compressive force, N = 11298 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 40212 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0201 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 2.060 %
Horizontal shear force, Vu = 1225 kN
Shear stress (vv = Vu /(bv . dv) = 1255.64 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.940 Mpa
= 940 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 832.311 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.50
Modified shear strength of concrete (n s vc ) = 1248.05 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 7.41 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.38 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 12.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30810 1005 1DL29869
+ 1SIDL 5218.422
+ 1CL + 1PLA +-1.524
1PLB + 1.1TLA
-3.187
+ 1.1TLB-0.83
+ 1.1BTA-25.628
+ 1.1BTB -171.879
Min Fx 30952 1001 1DL30011
+ 1SIDL 3595.392
+ 1CL + 1PLA +-6.152
1.1TLA + 1.1BTA
4.34 -0.038 -9.39 -113.902
Max Fy 30846 1006 1DL29905
+ 1SIDL 4462.643
+ 1CL + 1PLA + 5.714
1PLB + 1.1TLA
3.398
+ 1.1TLB
-0.677
- 1.1BTA - 1.1BTB
3.62 22.345
Min Fy 30940 1005 1DL29999
+ 1SIDL 5139.809
+ 1CL + 1PLA +-18.62
1PLB + 1.1TLA
3.507
+ 1.1TLB
-0.564
+ 1.1BTA-25.415
+ 1.1BTB -104.594
Max Fz 30846 1001 1DL29905
+ 1SIDL 4346.796
+ 1CL + 1PLA +-0.231
1.1TLA + 1.1BTA
4.531 -0.159 -7.739 -119
Min Fz 30792 1004 1DL29851
+ 1SIDL 4122.935
+ 1CL + 1PLB +-2.612
1.1TLB - 1.1BTB
-3.833 -0.553 -17.465 -8.04
Max Mx 30970 1001 1DL30029
+ 1SIDL 4245.533
+ 1CL + 1PLA +-0.297
1.1TLA + 1.1BTA
4.51 -0.025 -8.99 -126.138
Min Mx 30792 1003 1DL29851
+ 1SIDL +3773.78
1CL + 1PLB +-6.231
1.1TLB + -3.636
1.1BTB -1.06 -19.696 -104.974
Max My 30832 1002 1DL29892
+ 1SIDL 4093.257
+ 1CL + 1PLA +-1.282
1.1TLA - 1.1BTA
0.242 -0.592 13.794 0.474
Min My 30935 1005 1DL29995
+ 1SIDL 5139.809
+ 1CL + 1PLA +-8.101
1PLB + 1.1TLA
-0.99
+ 1.1TLB
-0.564
+ 1.1BTA-32.878
+ 1.1BTB -168.733
Max Mz 30828 1006 1DL29888
+ 1SIDL 4884.015
+ 1CL + 1PLA +-1.281
1PLB + 1.1TLA
3.582
+ 1.1TLB
-0.682
- 1.1BTA - 1.1BTB
7.593 38.247
Min Mz 30934 1005 1DL29993
+ 1SIDL 5139.809
+ 1CL + 1PLA +-1.582
1PLB + 1.1TLA
-2.957
+ 1.1TLB
-0.564
+ 1.1BTA-28.932
+ 1.1BTB -178.416

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30934 1095 1DL29993
+ 1SIDL 8499.962
+ 0.3CL + 0.3PLA
10.053
+ 0.3PLB +35.97
0.33TLA +9.918
0.33TLB1248.677
+ 0.33BTA + 222.878
0.33BTB + 0.3SLX + 0.
Min Fx 30792 1015 1DL29852
+ 1SIDL-1802.721
+ 0.3SLX + 0.3SLY
-13.427
+ 1SLZ -41.163 -10.739 -1279.227 -334.742
Max Fy 30833 1086 1DL29893
+ 1SIDL 7243.106
+ 0.3CL + 0.3PLA
99.962
+ 0.3PLB58.826
+ 0.33TLA 18.167
+ 0.33TLB -306.499
0.33BTA - 0.33BTB
519.155- 1SLX - 0.3SLY
Min Fy 30939 1079 1DL29999
+ 1SIDL + -27.778
0.3CL + 0.3PLA
-111.152
+ 0.3PLB-47.831
+ 0.33TLA-19.064
+ 0.33TLB-274.099
+ 0.33BTA + 0.33BTB
-579.24 + 1SLX + 0.3S
Max Fz 30797 3047 1DL29856
+ 1SIDL 8007.645
+ 0.3CL + 0.3PLA
25.729
+ 0.33TLA
137.381
+ 0.33BTA
10.071
+ 0.3SLX
806.513
+ 0.3SLY 162.672
+ 1SLZ + 1.1NLA
Min Fz 30851 3054 1DL29910
+ 1SIDL-1323.525
+ 0.3CL + 0.3PLA
-36.131
+ 0.33TLA
-135.752
- 0.33BTA
-11.447
- 0.3SLX
-815.101
- 0.3SLY --228.018
1SLZ - 1.1NLA
Max Mx 30810 3031 1DL29869
+ 1SIDL +7347.75
0.3CL + 0.3PLA
30.38
+ 0.33TLA 16.035
+ 0.33BTA
19.983
+ 1SLX544.734
+ 0.3SLY + 912.424
0.3SLZ + 1.1NLA
Min Mx 30810 3055 1DL29870
+ 1SIDL +-229.298
0.3CL + 0.3PLB
-28.942
+ 0.33TLB-20.538
+ 0.33BTB
-21.183
+ 1SLX
-559.675
+ 0.3SLY + -1023.47
0.3SLZ + 1.1NLB
Max My 30846 3071 1DL29905
+ 1SIDL 8314.165
+ 0.3CL + 0.3PLB
10.953
+ 0.33TLB 41.27
+ 0.33BTB
9.43
+ 0.3SLX
1308.121
+ 0.3SLY +238.321
1SLZ + 1.1NLB
Min My 30792 3078 1DL29851
+ 1SIDL-1418.434
+ 0.3CL + 0.3PLB
-13.252
+ 0.33TLB-41.446
- 0.33BTB
-10.318
- 0.3SLX
-1326.309
- 0.3SLY - -338.095
1SLZ - 1.1NLB
Max Mz 30828 1007 1DL29887
+ 1SIDL 6648.806
+ 1SLX + 0.3SLY26.432
+ 0.3SLZ 19.957 18.214 564.761 942.514
Min Mz 30934 1079 1DL29994
+ 1SIDL + -27.778
0.3CL + 0.3PLA
-29.157
+ 0.3PLB-17.328
+ 0.33TLA-19.064
+ 0.33TLB-490.758
+ 0.33BTA-1044.882
+ 0.33BTB + 1SLX + 0.3S
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30846 2103 1.15DL
29905
+ 1.2SIDL
11298.346
+ 1.4CL +55.356
1.4PLB + 1.54TLB
13.645 + 33.041
1.54BTB 373.897 1739.835
Min Fx 30792 2115 1.15DL
29852
+ 1.2SIDL
-2557.087
+ 0.3SLX-16.537
+ 0.3SLY + 1SLZ
-51.487 -13.42 -1604.571 -416.622
Max Fy 30797 2104 1.15DL
29856
+ 1.2SIDL
10962.077
+ 1.4CL195.538
+ 1.4PLB + 1.54TLB
40.86 - 1.54BTB
34.964 223.506 1205.851
Min Fy 30975 2103 1.15DL
30035
+ 1.2SIDL
-1265.006
+ 1.4CL-212.118
+ 1.4PLB + 1.54TLB
-21.509 + -31.555
1.54BTB -115.194 -1098.279
Max Fz 30797 3147 1.15DL
29856
+ 1.2SIDL
9807.961
+ 0.42CL32.453
+ 0.42PLA 172.507
+ 0.462TLA12.776
+ 0.462BTA
1012.929
+ 0.3SLX204.746
+ 0.3SLY + 1SLZ + 1.5
Min Fz 30851 3154 1.15DL
29910
+ 1.2SIDL
-1930.926
+ 0.42CL-44.736
+ 0.42PLA-170.629
+ 0.462TLA-14.381
- 0.462BTA
-1022.451
- 0.3SLX-281.935
- 0.3SLY - 1SLZ - 1.54N
Max Mx 30810 2104 1.15DL
29869
+ 1.2SIDL
9358.045
+ 1.4CL +60.819
1.4PLB + 1.54TLB
9.024 - 1.54BTB
35.392 358.61 1874.617
Min Mx 30810 2103 1.15DL
29870
+ 1.2SIDL
-98.69
+ 1.4CL -57.735
+ 1.4PLB + 1.54TLB
-15.697 + -36.724
1.54BTB -383.546 -1978.651
Max My 30846 3171 1.15DL
29905
+ 1.2SIDL
10189.748
+ 0.42CL13.607
+ 0.42PLB +51.552
0.462TLB11.817
+ 0.462BTB
1643.773
+ 0.3SLX301.464
+ 0.3SLY + 1SLZ + 1.5
Min My 30792 3178 1.15DL
29851
+ 1.2SIDL
-2019.086
+ 0.42CL-16.292
+ 0.42PLB +-51.882
0.462TLB
-12.831
- 0.462BTB
-1665.357
- 0.3SLX-419.137
- 0.3SLY - 1SLZ - 1.54N
Max Mz 30792 2104 1.15DL
29851
+ 1.2SIDL
10962.077
+ 1.4CL + 1.4PLB
53.88 + 1.54TLB
6.833 - 1.54BTB
34.964 363.387 1889.217
Min Mz 30970 2103 1.15DL
30030
+ 1.2SIDL
-1265.006
+ 1.4CL -57.481
+ 1.4PLB + 1.54TLB
-2.542 + -31.555
1.54BTB -219.143 -1991.847

ODE MDE
Maximum Tension Force (kN) -1802.72 -2557.09
Skin Friction (kN) 1110.67
Final Axial Load (kN) -692.05 -1446.42

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


40 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -154.3 2004 3161 0.634 OK
Minima 9808 1033 4537 0.228 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 85.82 OK
Minima -218.9 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.066 OK 34.74 OK
Minima 2.27 OK 17.16 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C24, C26, C28 & C30


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C24, C26, C28 & C30

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 4
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31147 1005 1DL30203
+ 1SIDL +4868.12
1CL + 1PLA109.082
+ 1PLB + 1.1TLA
-24.827
+ 1.1TLB0.155
+ 1.1BTA160.926
+ 1.1BTB 496.237
Min Fx 31024 1001 1DL30080
+ 1SIDL 3223.753
+ 1CL + 1PLA +55.233
1.1TLA + 1.1BTA
6.399 0.685 -92.775 174.488
Max Fy 31023 1005 1DL30079
+ 1SIDL 4755.201
+ 1CL + 1PLA110.299
+ 1PLB + 1.1TLA
-27.557
+ 1.1TLB0.087
+ 1.1BTA172.984
+ 1.1BTB 501.115
Min Fy 31394 1006 1DL30450
+ 1SIDL 4519.729
+ 1CL + 1PLA -41.307
+ 1PLB + 1.1TLA
-25.029
+ 1.1TLB
-2.598
- 1.1BTA152.644
- 1.1BTB -217.905
Max Fz 31397 1001 1DL30453
+ 1SIDL 3912.368
+ 1CL + 1PLA +69.642
1.1TLA + 16.109
1.1BTA -0.349 -145.658 324.402
Min Fz 31023 1005 1DL30079
+ 1SIDL 4755.201
+ 1CL + 1PLA110.299
+ 1PLB + 1.1TLA
-27.557
+ 1.1TLB0.087
+ 1.1BTA172.984
+ 1.1BTB 501.115
Max Mx 31025 1001 1DL30081
+ 1SIDL 3895.881
+ 1CL + 1PLA +79.133
1.1TLA + 1.1BTA
7.292 0.696 -100.018 370.976
Min Mx 31396 1006 1DL30452
+ 1SIDL 4302.634
+ 1CL + 1PLA -40.911
+ 1PLB + 1.1TLA
3.961
+ 1.1TLB
-2.653
- 1.1BTA -85.637
- 1.1BTB -214.666
Max My 31023 1003 1DL30079
+ 1SIDL 4003.445
+ 1CL + 1PLB + 78.42
1.1TLB + -27.258
1.1BTB -0.496 181.054 368.665
Min My 31397 1001 1DL30453
+ 1SIDL 3912.368
+ 1CL + 1PLA +69.642
1.1TLA + 16.109
1.1BTA -0.349 -145.658 324.402
Max Mz 31023 1005 1DL30079
+ 1SIDL 4755.201
+ 1CL + 1PLA110.299
+ 1PLB + 1.1TLA
-27.557
+ 1.1TLB0.087
+ 1.1BTA172.984
+ 1.1BTB 501.115
Min Mz 31394 1006 1DL30450
+ 1SIDL 4519.729
+ 1CL + 1PLA -41.307
+ 1PLB + 1.1TLA
-25.029
+ 1.1TLB
-2.598
- 1.1BTA152.644
- 1.1BTB -217.905

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31271 1095 1DL30327
+ 1SIDL 8396.944
+ 0.3CL + 0.3PLA
248.099
+ 0.3PLB737.326
+ 0.33TLA +6.557
0.33TLB +3190.34
0.33BTA +1077.332
0.33BTB + 0.3SLX + 0.
Min Fx 31024 1015 1DL30084
+ 1SIDL-1858.528
+ 0.3SLX + 0.3SLY
-168.498
+ 1SLZ-728.456 -8.386 -2290.412 -573.031
Max Fy 31271 1079 1DL30327
+ 1SIDL 7968.573
+ 0.3CL + 0.3PLA
646.644
+ 0.3PLB263.385
+ 0.33TLA +9.323
0.33TLB1278.867
+ 0.33BTA +2682.466
0.33BTB + 1SLX + 0.3S
Min Fy 31272 1086 1DL30328
+ 1SIDL +-981.009
0.3CL + 0.3PLA
-592.633
+ 0.3PLB
-274.106
+ 0.33TLA-11.452
+ 0.33TLB-1241.429
- 0.33BTA -2461.543
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 31272 3054 1DL30332
+ 1SIDL +7881.03
0.3CL + 0.3PLA
200.719
+ 0.33TLA765.26
- 0.33BTA6.63
- 0.3SLX
2234.277
- 0.3SLY - 1SLZ
599.291
- 1.1NLA
Min Fz 31271 3078 1DL30327
+ 1SIDL-1269.264
+ 0.3CL + 0.3PLB
-163.71
+ 0.33TLB
-775.873
- 0.33BTB
-8.674
- 0.3SLX
-2946.065
- 0.3SLY - -641.939
1SLZ - 1.1NLB
Max Mx 31023 2031 1DL30079
+ 1SIDL 7442.183
+ 0.3CL + 0.3PLA
628.548
+ 0.33TLA
246.055
+ 0.33BTA
14.771
+ 1SLX1169.922
+ 0.3SLY +2597.675
0.3SLZ + 1.1LLA
Min Mx 31023 3062 1DL30079
+ 1SIDL +-546.214
0.3CL + 0.3PLB
-544.29
+ 0.33TLB
-282.554
- 0.33BTB
-14.955
- 1SLX-935.859
- 0.3SLY - 0.3SLZ
-2157.187- 1.1NLB
Max My 31271 1071 1DL30327
+ 1SIDL 8172.002
+ 0.3CL + 0.3PLB
238.536
+ 0.33TLB
736.852
+ 0.33BTB
6.399
+ 0.3SLX
3194.596
+ 0.3SLY +1037.48
1SLZ
Min My 31272 3054 1DL30328
+ 1SIDL-1564.611
+ 0.3CL + 0.3PLA
-184.781
+ 0.33TLA
-742.948
- 0.33BTA
-7.995
- 0.3SLX
-3173.094
- 0.3SLY --817.461
1SLZ - 1.1NLA
Max Mz 31271 1079 1DL30327
+ 1SIDL 7968.573
+ 0.3CL + 0.3PLA
646.644
+ 0.3PLB263.385
+ 0.33TLA +9.323
0.33TLB1278.867
+ 0.33BTA +2682.466
0.33BTB + 1SLX + 0.3S
Min Mz 31272 1086 1DL30328
+ 1SIDL +-981.009
0.3CL + 0.3PLA
-592.633
+ 0.3PLB
-274.106
+ 0.33TLA-11.452
+ 0.33TLB-1241.429
- 0.33BTA -2461.543
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31395 2103 1.15DL
30451
+ 1.2SIDL
10422.188
+ 1.4CL
1207.954
+ 1.4PLB + 1.54TLB
86.222 + 1.54BTB
17.3 564.455 4941.091
Min Fx 31024 2103 1.15DL
30084
+ 1.2SIDL
-2825.821
+ 1.4CL-1036.92
+ 1.4PLB + 1.54TLB
-84.656 + -24.042
1.54BTB -334.113 -3219.519
Max Fy 31147 2103 1.15DL
30203
+ 1.2SIDL
10363.973
+ 1.4CL
1219.821
+ 1.4PLB + 1.54TLB
73.041 + 17.302
1.54BTB 571.581 5000.218
Min Fy 31272 2104 1.15DL
30332
+ 1.2SIDL
-2155.111
+ 1.4CL-1141.15
+ 1.4PLB + 1.54TLB
-98.034 - -18.564
1.54BTB -430.994 -3537.496
Max Fz 31272 3154 1.15DL
30332
+ 1.2SIDL
9635.188
+ 0.42CL249.267
+ 0.42PLA 960.618
+ 0.462TLA -8.426
0.462BTA
2804.663
- 0.3SLX - 747.15
0.3SLY - 1SLZ - 1.54N
Min Fz 31271 3178 1.15DL
30327
+ 1.2SIDL
-1892.271
+ 0.42CL
-209.812
+ 0.42PLB-973.016
+ 0.462TLB-10.884
- 0.462BTB
-3700.143
- 0.3SLX-826.332
- 0.3SLY - 1SLZ - 1.54
Max Mx 31023 2104 1.15DL
30079
+ 1.2SIDL
9158.862
+ 1.4CL
1125.999
+ 1.4PLB + 1.54TLB
65.57 - 1.54BTB
25.292 485.233 4618.317
Min Mx 31022 2103 1.15DL
30082
+ 1.2SIDL
-2554.287
+ 1.4CL-1036.77
+ 1.4PLB + -100.563
1.54TLB + 1.54BTB
-25.91 -100.174 -3218.445
Max My 31271 2171 1.15DL
30327
+ 1.2SIDL
9967.692
+ 0.42CL297.416
+ 0.42PLB 925.625
+ 0.462TLB8.132
+ 0.462BTB
4000.432
+ 0.3SLX
1289.502
+ 0.3SLY + 1SLZ
Min My 31272 3154 1.15DL
30328
+ 1.2SIDL
-2215.466
+ 0.42CL
-234.414
+ 0.42PLA-931.837
+ 0.462TLA-9.926
- 0.462BTA
-3978.708
- 0.3SLX-1031.775
- 0.3SLY - 1SLZ - 1.54N
Max Mz 31147 2103 1.15DL
30203
+ 1.2SIDL
10363.973
+ 1.4CL
1219.821
+ 1.4PLB + 1.54TLB
73.041 + 17.302
1.54BTB 571.581 5000.218
Min Mz 31272 2104 1.15DL
30332
+ 1.2SIDL
-2155.111
+ 1.4CL-1141.15
+ 1.4PLB + 1.54TLB
-98.034 - -18.564
1.54BTB -430.994 -3537.496

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 4868.12 3223.753 9575.000 OK
ODE Seismic 8396.944 -1858.528 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -2215 4110 4607 0.892 OK
Minima 9635 2902 6145 0.472 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 144 OK
Minima -309.1 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.969 OK 38.75 OK
Minima 0.9757 OK 10.11 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 21.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31239 1005 1DL30287
+ 1SIDL +4868.12
1CL + 1PLA -14.216
+ 1PLB + 1.1TLA
2.984
+ 1.1TLB0.155
+ 1.1BTA-12.623
+ 1.1BTB -48.155
Min Fx 31124 1001 1DL30164
+ 1SIDL 3223.753
+ 1CL + 1PLA + 1.1TLA
-7.6 + 1.1BTA-0.5 0.685 5.032 -21.721
Max Fy 31478 1006 1DL30534
+ 1SIDL 4519.729
+ 1CL + 1PLA + 5.226
1PLB + 1.1TLA
3.059
+ 1.1TLB
-2.598
- 1.1BTA -12.393
- 1.1BTB 19.275
Min Fy 31115 1005 1DL30163
+ 1SIDL 4755.201
+ 1CL + 1PLA -14.378
+ 1PLB + 1.1TLA
3.342
+ 1.1TLB0.087
+ 1.1BTA-13.816
+ 1.1BTB -48.669
Max Fz 31115 1005 1DL30163
+ 1SIDL 4755.201
+ 1CL + 1PLA -14.378
+ 1PLB + 1.1TLA
3.342
+ 1.1TLB0.087
+ 1.1BTA-13.816
+ 1.1BTB -48.669
Min Fz 31505 1001 1DL30537
+ 1SIDL 3912.368
+ 1CL + 1PLA +-9.036
1.1TLA + 1.1BTA
-1.72 -0.349 9.62 -31.007
Max Mx 31133 1001 1DL30165
+ 1SIDL 3895.881
+ 1CL + 1PLA -10.255
+ 1.1TLA + 1.1BTA
-0.6 0.696 5.536 -35.314
Min Mx 31496 1006 1DL30536
+ 1SIDL 4302.634
+ 1CL + 1PLA + 5.182
1PLB + 1.1TLA
-0.162
+ 1.1TLB
-2.653
- 1.1BTA - 1.1BTB
4.093 19.05
Max My 31505 1001 1DL30537
+ 1SIDL 3912.368
+ 1CL + 1PLA +-9.036
1.1TLA + 1.1BTA
-1.72 -0.349 9.62 -31.007
Min My 31115 1003 1DL30163
+ 1SIDL 4003.445
+ 1CL + 1PLB -10.157
+ 1.1TLB + 1.1BTB
3.253 -0.496 -14.011 -35.032
Max Mz 31478 1006 1DL30534
+ 1SIDL 4519.729
+ 1CL + 1PLA + 5.226
1PLB + 1.1TLA
3.059
+ 1.1TLB
-2.598
- 1.1BTA -12.393
- 1.1BTB 19.275
Min Mz 31115 1005 1DL30163
+ 1SIDL 4755.201
+ 1CL + 1PLA -14.378
+ 1PLB + 1.1TLA
3.342
+ 1.1TLB0.087
+ 1.1BTA-13.816
+ 1.1BTB -48.669
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31363 1095 1DL30411
+ 1SIDL 8396.944
+ 0.3CL + 0.3PLA18.3
+ 0.3PLB102.215
+ 0.33TLA +6.557
0.33TLB +311.983
0.33BTA + 0.33BTB
57.386 + 0.3SLX + 0.
Min Fx 31124 1015 1DL30184
+ 1SIDL-1858.528
+ 0.3SLX + 0.3SLY
-27.425
+ 1SLZ -97.653 -8.386 -210.692 -59.378
Max Fy 31372 1086 1DL30432
+ 1SIDL 7689.216
+ 0.3CL + 0.3PLA
78.465
+ 0.3PLB36.557
+ 0.33TLA + 0.33TLB
8.88 - 0.33BTA
86.66 - 0.33BTB
175.021- 1SLX - 0.3SLY
Min Fy 31363 1079 1DL30423
+ 1SIDL +-536.453
0.3CL + 0.3PLA
-85.634
+ 0.3PLB-35.086
+ 0.33TLA-10.611
+ 0.33TLB +-89.586
0.33BTA +-190.837
0.33BTB + 1SLX + 0.3S
Max Fz 31363 3078 1DL30423
+ 1SIDL 8092.505
+ 0.3CL + 0.3PLB
21.879
+ 0.33TLB
102.796
- 0.33BTB
5.729
- 0.3SLX
212.538
- 0.3SLY - 1SLZ
46.82
- 1.1NLB
Min Fz 31372 3054 1DL30412
+ 1SIDL-1564.611
+ 0.3CL + 0.3PLA
-26.757
+ 0.33TLA
-101.348
- 0.33BTA
-7.995
- 0.3SLX
-314.008
- 0.3SLY - 1SLZ
-84.663
- 1.1NLA
Max Mx 31115 2031 1DL30163
+ 1SIDL 7442.183
+ 0.3CL + 0.3PLA
70.259
+ 0.33TLA 36.507
+ 0.33BTA
14.771
+ 1SLX103.486
+ 0.3SLY + 221.795
0.3SLZ + 1.1LLA
Min Mx 31115 3062 1DL30163
+ 1SIDL +-546.214
0.3CL + 0.3PLB
-80.94
+ 0.33TLB-32.107
- 0.33BTB
-14.955
- 1SLX-121.957
- 0.3SLY - 0.3SLZ
-260.973
- 1.1NLB
Max My 31372 2047 1DL30412
+ 1SIDL 7832.799
+ 0.3CL + 0.3PLA
21.963
+ 0.33TLA 99.401
+ 0.33BTA
6.621
+ 0.3SLX
325.868
+ 0.3SLY +73.816
1SLZ + 1.1LLA
Min My 31363 3078 1DL30411
+ 1SIDL-1269.264
+ 0.3CL + 0.3PLB
-29.028
+ 0.33TLB-97.552
- 0.33BTB
-8.674
- 0.3SLX
-331.389
- 0.3SLY - 1SLZ
-96.424
- 1.1NLB
Max Mz 31372 1007 1DL30412
+ 1SIDL 7243.809
+ 1SLX + 0.3SLY76.371
+ 0.3SLZ 36.658 9.341 123.661 246.688
Min Mz 31363 1014 1DL30411
+ 1SIDL --1013.99
1SLX - 0.3SLY
-82.841
- 0.3SLZ -35.373 -10.833 -127.526 -267.425

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31487 2103 1.15DL
30535
+ 1.2SIDL
10422.188
+ 1.4CL137.216
+ 1.4PLB + 1.54TLB
16.119 + 1.54BTB
17.3 35.296 435.788
Min Fx 31124 2103 1.15DL
30184
+ 1.2SIDL
-2825.821
+ 1.4CL-157.455
+ 1.4PLB + 1.54TLB
-10.996 + -24.042
1.54BTB -23.945 -342.335
Max Fy 31372 2104 1.15DL
30412
+ 1.2SIDL
10033.16
+ 1.4CL151.408
+ 1.4PLB + 1.54TLB
13.134 - 1.54BTB
15.177 50.467 485.977
Min Fy 31239 2103 1.15DL
30299
+ 1.2SIDL
-1538.276
+ 1.4CL -161.85
+ 1.4PLB + 1.54TLB
-9.813 + -18.026
1.54BTB -38.006 -357.607
Max Fz 31363 3178 1.15DL
30423
+ 1.2SIDL
9856.396
+ 0.42CL28.021
+ 0.42PLB 128.935
+ 0.462TLB7.193
- 0.462BTB
266.889
- 0.3SLX - 0.3SLY
60.15 - 1SLZ - 1.54
Min Fz 31372 3154 1.15DL
30412
+ 1.2SIDL
-2215.466
+ 0.42CL-33.214
+ 0.42PLA-127.244
+ 0.462TLA-9.926
- 0.462BTA
-393.924
- 0.3SLX-105.242
- 0.3SLY - 1SLZ - 1.54N
Max Mx 31115 2104 1.15DL
30163
+ 1.2SIDL
9158.862
+ 1.4CL144.895
+ 1.4PLB + 1.54TLB
13.059 - 1.54BTB
25.292 26.452 458.254
Min Mx 31106 2103 1.15DL
30166
+ 1.2SIDL
-2554.287
+ 1.4CL-157.435
+ 1.4PLB + 1.54TLB
-7.447 + 1.54BTB
-25.91 -31.155 -342.258
Max My 31372 2347 1.15DL
30412
+ 1.2SIDL
9567.666
+ 0.42CL27.595
+ 0.42PLA 124.729
+ 0.462TLA +8.414
0.462BTA
408.721
+ 0.3SLX +92.55
0.3SLY + 1SLZ + 1.5
Min My 31363 3178 1.15DL
30411
+ 1.2SIDL
-1892.271
+ 0.42CL-35.861
+ 0.42PLB +-122.46
0.462TLB
-10.884
- 0.462BTB
-415.462
- 0.3SLX-118.981
- 0.3SLY - 1SLZ - 1.54
Max Mz 31372 2104 1.15DL
30412
+ 1.2SIDL
10033.16
+ 1.4CL151.408
+ 1.4PLB + 1.54TLB
13.134 - 1.54BTB
15.177 50.467 485.977
Min Mz 31239 1452 1.15DL
30287
+ 1.2SIDL
7700.692
- 1.5COL(-X)-MLC
-116.563 7.194 -1.23 -26.58 -378.155

ODE MDE
Maximum Tension Force (kN) -1858.53 -2825.82
Skin Friction (kN) 3631.33
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 432.2 885.2 0.488 OK
Minima 9856 273.6 2996 0.091 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 62.06 OK
Minima -76.36 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.486 OK 31.63 OK
Minima 2.654 OK 19.15 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.954 m
Hence de = 0.904 m and dv = 0.813 m
Horizontal resultant shear force at the section, Vu = 1222 kN
Corresponding axial compressive force, N = 10364 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 40212 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0201 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 2.060 %
Horizontal shear force, Vu = 1222 kN
Shear stress (vv = Vu /(bv . dv) = 1252.11 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.940 Mpa
= 940 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 832.311 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.46
Modified shear strength of concrete (n s vc ) = 1213.67 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 37.51 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.38 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 14.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31184 1005 1DL30243
+ 1SIDL +4868.12
1CL + 1PLA -12.292
+ 1PLB + 1.1TLA
0.332
+ 1.1TLB0.155
+ 1.1BTA-27.959
+ 1.1BTB -159.939
Min Fx 31078 1001 1DL30137
+ 1SIDL 3223.753
+ 1CL + 1PLA -10.169
+ 1.1TLA + 1.1BTA
2.55 0.685 -1.82 -94.493
Max Fy 31432 1006 1DL30491
+ 1SIDL 4134.326
+ 1CL + 1PLA + 5.298
1PLB + 1.1TLA
0.873
+ 1.1TLB
-2.576
- 1.1BTA -29.355
- 1.1BTB 31.695
Min Fy 31042 1005 1DL30101
+ 1SIDL 3728.086
+ 1CL + 1PLA -14.606
+ 1PLB + 1.1TLA0.76
+ 1.1TLB0.061
+ 1.1BTA-30.832
+ 1.1BTB -138.683
Max Fz 31450 1006 1DL30509
+ 1SIDL 4302.634
+ 1CL + 1PLA + 3.143
1PLB + 1.1TLA
3.028
+ 1.1TLB
-2.653
- 1.1BTA - 1.1BTB
-6.09 54.96
Min Fz 31042 1006 1DL30101
+ 1SIDL +4450.45
1CL + 1PLA + 2.087
1PLB + 1.1TLA
-0.77
+ 1.1TLB
-0.377
- 1.1BTA -15.372
- 1.1BTB 39.951
Max Mx 31096 1001 1DL30155
+ 1SIDL 3895.881
+ 1CL + 1PLA +-8.353
1.1TLA + 1.1BTA
2.613 0.696 -1.071 -114.094
Min Mx 31450 1006 1DL30509
+ 1SIDL 4302.634
+ 1CL + 1PLA + 3.143
1PLB + 1.1TLA
3.028
+ 1.1TLB
-2.653
- 1.1BTA - 1.1BTB
-6.09 54.96
Max My 31468 1001 1DL30528
+ 1SIDL 3912.368
+ 1CL + 1PLA +-7.458
1.1TLA + 1.1BTA
1.903 -0.349 12.789 -93.318
Min My 31060 1005 1DL30119
+ 1SIDL 4755.201
+ 1CL + 1PLA -12.463
+ 1PLB + 1.1TLA
0.659
+ 1.1TLB0.087
+ 1.1BTA-32.026
+ 1.1BTB -161.839
Max Mz 31414 1006 1DL30473
+ 1SIDL 4519.729
+ 1CL + 1PLA + 3.114
1PLB + 1.1TLA
0.828
+ 1.1TLB
-2.598
- 1.1BTA -29.874
- 1.1BTB 55.288
Min Mz 31060 1005 1DL30119
+ 1SIDL 4755.201
+ 1CL + 1PLA -12.463
+ 1PLB + 1.1TLA
0.659
+ 1.1TLB0.087
+ 1.1BTA-32.026
+ 1.1BTB -161.839

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31308 1095 1DL30367
+ 1SIDL 8396.944
+ 0.3CL + 0.3PLA
20.092
+ 0.3PLB103.388
+ 0.33TLA +6.557
0.33TLB1149.726
+ 0.33BTA + 216.275
0.33BTB + 0.3SLX + 0.
Min Fx 31078 1015 1DL30138
+ 1SIDL-1858.528
+ 0.3SLX + 0.3SLY
-29.335
+ 1SLZ -99.676 -8.386 -1035.89 -293.064
Max Fy 31344 1086 1DL30404
+ 1SIDL 7291.232
+ 0.3CL + 0.3PLA80.83
+ 0.3PLB39.571
+ 0.33TLA +8.862
0.33TLB -389.391
0.33BTA - 0.33BTB
808.733- 1SLX - 0.3SLY
Min Fy 31166 1079 1DL30226
+ 1SIDL +-634.428
0.3CL + 0.3PLA
-88.199
+ 0.3PLB-36.551
+ 0.33TLA-10.861
+ 0.33TLB-394.225
+ 0.33BTA + 0.33BTB
-884.95 + 1SLX + 0.3S
Max Fz 31344 3047 1DL30403
+ 1SIDL 7909.314
+ 0.3CL + 0.3PLA
21.829
+ 0.33TLA
105.966
+ 0.33BTA
6.155
+ 0.3SLX
1160.465
+ 0.3SLY 225.189
+ 1SLZ + 1.1NLA
Min Fz 31290 3071 1DL30350
+ 1SIDL-1411.865
+ 0.3CL + 0.3PLB
-31.645
+ 0.33TLB
-103.994
+ 0.33BTB
-7.617
+ 0.3SLX
-1075.488
+ 0.3SLY-303.904
+ 1SLZ + 1.1NLB
Max Mx 31060 2031 1DL30119
+ 1SIDL 7442.183
+ 0.3CL + 0.3PLA
75.299
+ 0.33TLA 35.807
+ 0.33BTA
14.771
+ 1SLX 386.96
+ 0.3SLY + 0.3SLZ
826.68+ 1.1LLA
Min Mx 31060 3062 1DL30119
+ 1SIDL +-546.214
0.3CL + 0.3PLB
-81.856
+ 0.33TLB-35.189
- 0.33BTB
-14.955
- 1SLX-428.508
- 0.3SLY - 0.3SLZ
-940.16
- 1.1NLB
Max My 31326 3071 1DL30385
+ 1SIDL 7819.343
+ 0.3CL + 0.3PLB
19.687
+ 0.33TLB
104.309
+ 0.33BTB
7.022
+ 0.3SLX
1173.917
+ 0.3SLY +248.424
1SLZ + 1.1NLB
Min My 31308 3078 1DL30367
+ 1SIDL-1269.264
+ 0.3CL + 0.3PLB
-26.956
+ 0.33TLB
-102.585
- 0.33BTB
-8.674
- 0.3SLX
-1194.119
- 0.3SLY - -330.949
1SLZ - 1.1NLB
Max Mz 31326 1007 1DL30385
+ 1SIDL 7243.809
+ 1SLX + 0.3SLY76.842
+ 0.3SLZ 38.906 9.341 430.569 886.093
Min Mz 31308 1014 1DL30367
+ 1SIDL --1013.99
1SLX - 0.3SLY
-83.485
- 0.3SLZ -37.193 -10.833 -446.802 -961.517
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31433 2103 1.15DL
30492
+ 1.2SIDL
10422.188
+ 1.4CL +166.75
1.4PLB + 1.54TLB
17.021 + 1.54BTB
17.3 126.699 1463.994
Min Fx 31079 2103 1.15DL
30139
+ 1.2SIDL
-2825.821
+ 1.4CL-191.553
+ 1.4PLB + 1.54TLB
-10.674 + -24.042
1.54BTB -107.878 -1488.765
Max Fy 31345 2104 1.15DL
30404
+ 1.2SIDL
9056.395
+ 1.4CL180.874
+ 1.4PLB + 1.54TLB
16.855 - 1.54BTB
15.169 134.915 1584.45
Min Fy 31167 2103 1.15DL
30227
+ 1.2SIDL
-1828.948
+ 1.4CL-193.317
+ 1.4PLB + 1.54TLB
-12.85 + -18.086
1.54BTB -126.521 -1502.504
Max Fz 31345 3147 1.15DL
30404
+ 1.2SIDL
9640.003
+ 0.42CL30.883
+ 0.42PLA 153.078
+ 0.462TLA +7.768
0.462BTA
1328.683
+ 0.3SLX257.568
+ 0.3SLY + 1SLZ + 1.5
Min Fz 31291 3171 1.15DL
30351
+ 1.2SIDL
-2058.688
+ 0.42CL -44.85
+ 0.42PLB-150.598
+ 0.462TLB-9.393
+ 0.462BTB
-1197.201
+ 0.3SLX-336.147
+ 0.3SLY + 1SLZ + 1.
Max Mx 31061 2104 1.15DL
30120
+ 1.2SIDL
9158.862
+ 1.4CL177.523
+ 1.4PLB + 1.54TLB
12.944 - 1.54BTB
25.292 97.838 1548.503
Min Mx 31043 2103 1.15DL
30103
+ 1.2SIDL
-2554.287
+ 1.4CL-191.555
+ 1.4PLB + 1.54TLB
-11.491 + 1.54BTB
-25.91 -122.601 -1488.598
Max My 31327 3171 1.15DL
30386
+ 1.2SIDL
9548.827
+ 0.42CL29.977
+ 0.42PLB 150.851
+ 0.462TLB8.975
+ 0.462BTB
1345.404
+ 0.3SLX287.766
+ 0.3SLY + 1SLZ + 1.
Min My 31309 3178 1.15DL
30368
+ 1.2SIDL
-1892.271
+ 0.42CL-39.868
+ 0.42PLB-148.507
+ 0.462TLB -10.884
- 0.462BTB
-1367.653
- 0.3SLX-375.854
- 0.3SLY - 1SLZ - 1.54
Max Mz 31327 2104 1.15DL
30386
+ 1.2SIDL
10033.16
+ 1.4CL180.161
+ 1.4PLB + 1.54TLB
16.582 - 1.54BTB
15.177 146.819 1608.561
Min Mz 31185 2103 1.15DL
30245
+ 1.2SIDL
-1538.276
+ 1.4CL-192.616
+ 1.4PLB + 1.54TLB
-12.597 + -18.026
1.54BTB -139.668 -1526.947

ODE MDE
Maximum Tension Force (kN) -1858.53 -2825.82
Skin Friction (kN) 2318.00
Final Axial Load (kN) 0.00 -507.82

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


40 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -507.8 1493 3055 0.489 OK
Minima 9640 1353 4543 0.298 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 81.67 OK
Minima -166.2 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.728 OK 32.42 OK
Minima 2.077 OK 15.62 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C25, C27, C29 & C31


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C25, C27, C29, C31

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25932 1006 1DL24802
+ 1SIDL +3633.26
1CL + 1PLA +-5.975
1PLB + 1.1TLA0.21
+ 1.1TLB
-1.118
- 1.1BTA - -21.94
1.1BTB 22.671
Min Fx 25866 1001 1DL24736
+ 1SIDL 2846.256
+ 1CL + 1PLA + 8.147
1.1TLA + -1.293
1.1BTA -0.061 -18.103 -47.65
Max Fy 25994 1005 1DL24834
+ 1SIDL 3029.437
+ 1CL + 1PLA +38.635
1PLB + 1.1TLA
-2.483
+ 1.1TLB0.164
+ 1.1BTA +-6.135
1.1BTB 19.835
Min Fy 25961 1006 1DL24801
+ 1SIDL +3633.26
1CL + 1PLA -15.127
+ 1PLB + 1.1TLA
-2.889
+ 1.1TLB
-1.118
- 1.1BTA -16.816
- 1.1BTB -12.667
Max Fz 25928 1003 1DL24768
+ 1SIDL 3050.474
+ 1CL + 1PLB +25.625
1.1TLB + 1.1BTB
6.106 -0.359 -23.916 16.306
Min Fz 25895 1001 1DL24735
+ 1SIDL 2846.256
+ 1CL + 1PLA +23.144
1.1TLA + -5.259
1.1BTA -0.061 -6.762 5.221
Max Mx 25965 1001 1DL24835
+ 1SIDL 2919.116
+ 1CL + 1PLA + 9.919
1.1TLA + -0.418
1.1BTA 0.282 -19.706 -45.425
Min Mx 25899 1006 1DL24769
+ 1SIDL 3089.231
+ 1CL + 1PLA +-3.736
1PLB + 1.1TLA
2.253
+ 1.1TLB
-1.201
- 1.1BTA - 1.1BTB
-18.4 26.998
Max My 25906 1003 1DL24777
+ 1SIDL 3050.474
+ 1CL + 1PLB +-5.364
1.1TLB + 1.1BTB
0.312 -0.359 7.485 -50.824
Min My 25932 1002 1DL24803
+ 1SIDL 3589.374
+ 1CL + 1PLA +-1.432
1.1TLA - 1.1BTA
-0.348 -0.826 -28.162 0.719
Max Mz 25935 1006 1DL24806
+ 1SIDL +3633.26
1CL + 1PLA +-0.726
1PLB + 1.1TLA
1.624
+ 1.1TLB
-1.118
- 1.1BTA -17.977
- 1.1BTB 35.308
Min Mz 25968 1005 1DL24839
+ 1SIDL 3029.437
+ 1CL + 1PLA + 0.708
1PLB + 1.1TLA
0.634
+ 1.1TLB0.164
+ 1.1BTA-10.593
+ 1.1BTB -97.49

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25932 1006 1DL24802
+ 1SIDL +3633.26
1CL + 1PLA +-5.975
1PLB + 1.1TLA0.21
+ 1.1TLB
-1.118
- 1.1BTA - -21.94
1.1BTB 22.671
Min Fx 25965 1007 1DL24836
+ 1SIDL 1972.633
+ 1SLX + 0.3SLY
-80.115
+ 0.3SLZ -32.066 -5.485 -223.024 -500.604
Max Fy 25928 1152 1DL24768
+ 1SIDL 2355.586
- 1COL(-X)-MLC
379.493 1.274 1.275 -28.686 835.125
Min Fy 25895 1086 1DL24735
+ 1SIDL 2331.032
+ 0.3CL + 0.3PLA
-225.73
+ 0.3PLB-96.974
+ 0.33TLA +-4.985
0.33TLB --40.231
0.33BTA - -140.087
0.33BTB - 1SLX - 0.3SLY
Max Fz 25928 3071 1DL24768
+ 1SIDL 2864.651
+ 0.3CL + 0.3PLB
86.325
+ 0.33TLB
269.991
+ 0.33BTB
3.152+ 0.3SLX53.334
+ 0.3SLY + 55.739
1SLZ + 1.1NLB
Min Fz 25895 3047 1DL24766
+ 1SIDL +2245.42
0.3CL + 0.3PLA
-60.75
+ 0.33TLA
-267.814
+ 0.33BTA-3.63
+ 0.3SLX
-210.289
+ 0.3SLY + -56.39
1SLZ + 1.1NLA
Max Mx 25965 2031 1DL24835
+ 1SIDL 2814.164
+ 0.3CL + 0.3PLA
87.798
+ 0.33TLA31.999
+ 0.33BTA5.428
+ 1SLX174.944
+ 0.3SLY + 371.142
0.3SLZ + 1.1LLA
Min Mx 25932 3062 1DL24802
+ 1SIDL 3217.057
+ 0.3CL + 0.3PLB
-83.632
+ 0.33TLB
-34.444
- 0.33BTB
-5.889
- 1SLX --221.21
0.3SLY - 0.3SLZ
-410.339
- 1.1NLB
Max My 25903 3071 1DL24773
+ 1SIDL 2864.651
+ 0.3CL + 0.3PLB
3.377
+ 0.33TLB22.579
+ 0.33BTB
3.152+ 0.3SLX
701.548
+ 0.3SLY +141.615
1SLZ + 1.1NLB
Min My 25934 3047 1DL24805
+ 1SIDL +3198.05
0.3CL + 0.3PLA
-7.871
+ 0.33TLA
-20.498
+ 0.33BTA
-4.018
+ 0.3SLX
-720.753
+ 0.3SLY-208.314
+ 1SLZ + 1.1NLA
Max Mz 25928 1152 1DL24768
+ 1SIDL 2355.586
- 1COL(-X)-MLC
379.493 1.274 1.275 -28.686 835.125
Min Mz 25905 1152 1DL24776
+ 1SIDL 2355.586
- 1COL(-X)-MLC4.888 2.333 1.275 -5.858 -647.865
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25932 2106 1.15DL
24802
+ 1.2SIDL
4307.411
+ 1.4CL +-8.812
1.4PLA + 1.4PLB
0.064+ 1.54TLA
-1.462
+ 1.54TLB
-27.358
- 1.54BTA36.481
- 1.54BTB
Min Fx 25965 2107 1.15DL
24836
+ 1.2SIDL
2238.501
+ 1SLX -100.945
+ 0.3SLY + 0.3SLZ
-40.214 -6.878 -279.326 -626.823
Max Fy 25928 1452 1.15DL
24768
+ 1.2SIDL
2667.677
- 1.5COL(-X)-MLC
565.88 0.41 2.06 -33.436 1250.181
Min Fy 25961 2104 1.15DL
24832
+ 1.2SIDL
4177.714
+ 1.4CL-437.129
+ 1.4PLB + 1.54TLB
-43.808 - 1.54BTB
-9.632 -50.308 -204.58
Max Fz 25928 3171 1.15DL
24768
+ 1.2SIDL
3360.771
+ 0.42CL108.051
+ 0.42PLB 338.687
+ 0.462TLB4.027
+ 0.462BTB68.734
+ 0.3SLX +69.146
0.3SLY + 1SLZ + 1.
Min Fz 25895 3147 1.15DL
24766
+ 1.2SIDL
2608.989
+ 0.42CL-76.242
+ 0.42PLA-336.303
+ 0.462TLA-4.531
+ 0.462BTA
-263.548
+ 0.3SLX-69.391
+ 0.3SLY + 1SLZ + 1.5
Max Mx 25965 2103 1.15DL
24835
+ 1.2SIDL
3990.5
+ 1.4CL +172.04
1.4PLB + 1.54TLB
9.521 + 1.54BTB
9.104 46.717 705.165
Min Mx 25932 2104 1.15DL
24803
+ 1.2SIDL
4177.714
+ 1.4CL-164.252
+ 1.4PLB + 1.54TLB
-14.351 - 1.54BTB
-9.632 -118.786 -917.561
Max My 25903 3171 1.15DL
24773
+ 1.2SIDL
3360.771
+ 0.42CL +4.204
0.42PLB +28.005
0.462TLB4.027
+ 0.462BTB
882.327
+ 0.3SLX178.661
+ 0.3SLY + 1SLZ + 1.
Min My 25934 3147 1.15DL
24805
+ 1.2SIDL
3708.627
+ 0.42CL -9.782
+ 0.42PLA + -25.85
0.462TLA-5.016
+ 0.462BTA
-905.206
+ 0.3SLX -261.179
+ 0.3SLY + 1SLZ + 1.5
Max Mz 25928 1452 1.15DL
24768
+ 1.2SIDL
2667.677
- 1.5COL(-X)-MLC
565.88 0.41 2.06 -33.436 1250.181
Min Mz 25902 2103 1.15DL
24773
+ 1.2SIDL
3274.245
+ 1.4CL +-8.147
1.4PLB + 1.54TLB
1.468 + 1.54BTB
-8.529 -93.185 -1162.734

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 3633.26 2846.256 7790.000 OK
ODE Seismic 3633.26 1972.633 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 2668 1251 1430 0.875 OK
Minima 4307 45.61 1692 0.027 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 79.57 OK
Minima -75.37 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.856 OK 34 OK
Minima 2.763 OK 21.43 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 16.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25945 1006 1DL24815
+ 1SIDL +3633.26
1CL + 1PLA + 1PLB
3.23+ 1.1TLA
1.029
+ 1.1TLB
-1.118
- 1.1BTA - -1.855
1.1BTB 10.207
Min Fx 25879 1001 1DL24749
+ 1SIDL 2846.256
+ 1CL + 1PLA +-5.246
1.1TLA + 1.1BTA
1.362 -0.061 -3.493 -15.547
Max Fy 25945 1006 1DL24815
+ 1SIDL +3633.26
1CL + 1PLA + 1PLB
3.23+ 1.1TLA
1.029
+ 1.1TLB
-1.118
- 1.1BTA - -1.855
1.1BTB 10.207
Min Fy 25978 1005 1DL24848
+ 1SIDL 3029.437
+ 1CL + 1PLA +-8.519
1PLB + 1.1TLA
0.706
+ 1.1TLB0.164
+ 1.1BTA +-1.635
1.1BTB -26.007
Max Fz 25945 1002 1DL24815
+ 1SIDL 3589.374
+ 1CL + 1PLA + 0.465
1.1TLA - 1.1BTA
1.52 -0.826 -3.174 1.847
Min Fz 25912 1003 1DL24782
+ 1SIDL 3050.474
+ 1CL + 1PLB +-5.583
1.1TLB + -0.901
1.1BTB -0.359 4.213 -17.265
Max Mx 25978 1001 1DL24848
+ 1SIDL 2919.116
+ 1CL + 1PLA +-5.754
1.1TLA + 1.1BTA
1.137 0.282 -2.478 -17.702
Min Mx 25912 1006 1DL24782
+ 1SIDL 3089.231
+ 1CL + 1PLA + 2.665
1PLB + 1.1TLA
0.137
+ 1.1TLB
-1.201
- 1.1BTA - 1.1BTB
1.225 7.631
Max My 25912 1003 1DL24782
+ 1SIDL 3050.474
+ 1CL + 1PLB +-5.583
1.1TLB + -0.901
1.1BTB -0.359 4.213 -17.265
Min My 25879 1001 1DL24749
+ 1SIDL 2846.256
+ 1CL + 1PLA +-5.246
1.1TLA + 1.1BTA
1.362 -0.061 -3.493 -15.547
Max Mz 25945 1006 1DL24815
+ 1SIDL +3633.26
1CL + 1PLA + 1PLB
3.23+ 1.1TLA
1.029
+ 1.1TLB
-1.118
- 1.1BTA - -1.855
1.1BTB 10.207
Min Mz 25978 1005 1DL24848
+ 1SIDL 3029.437
+ 1CL + 1PLA +-8.519
1PLB + 1.1TLA
0.706
+ 1.1TLB0.164
+ 1.1BTA +-1.635
1.1BTB -26.007
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25945 1006 1DL24815
+ 1SIDL +3633.26
1CL + 1PLA + 1PLB
3.23+ 1.1TLA
1.029
+ 1.1TLB
-1.118
- 1.1BTA - -1.855
1.1BTB 10.207
Min Fx 25978 1007 1DL24849
+ 1SIDL 1972.633
+ 1SLX + 0.3SLY
-50.744
+ 0.3SLZ -20.117 -5.485 -40.556 -104.166
Max Fy 25879 1086 1DL24750
+ 1SIDL +2631.92
0.3CL + 0.3PLA
49.28
+ 0.3PLB21.726
+ 0.33TLA +4.027
0.33TLB - 0.33BTA
42.03 - 0.33BTB
102.787- 1SLX - 0.3SLY
Min Fy 25912 1152 1DL24782
+ 1SIDL 2355.586
- 1COL(-X)-MLC
-69.948 0.32 1.275 0.996 -258.613
Max Fz 25879 3047 1DL24749
+ 1SIDL +2662.64
0.3CL + 0.3PLA
12.991
+ 0.33TLA60.419
+ 0.33BTA2.923
+ 0.3SLX
174.046
+ 0.3SLY +40.988
1SLZ + 1.1NLA
Min Fz 25912 3071 1DL24783
+ 1SIDL 2437.386
+ 0.3CL + 0.3PLB
-18.803
+ 0.33TLB
-60.269
+ 0.33BTB
-3.644+ 0.3SLX
-113.975
+ 0.3SLY +-39.363
1SLZ + 1.1NLB
Max Mx 25978 2031 1DL24848
+ 1SIDL 2814.164
+ 0.3CL + 0.3PLA
45.81
+ 0.33TLA21.025
+ 0.33BTA5.428
+ 1SLX +59.42
0.3SLY + 140.271
0.3SLZ + 1.1LLA
Min Mx 25945 3062 1DL24815
+ 1SIDL 3217.057
+ 0.3CL + 0.3PLB
-50.248
+ 0.33TLB
-21.537
- 0.33BTB
-5.889
- 1SLX --67.413
0.3SLY - 0.3SLZ
-153.572
- 1.1NLB
Max My 25912 3071 1DL24782
+ 1SIDL 2864.651
+ 0.3CL + 0.3PLB
12.534
+ 0.33TLB 58.27
+ 0.33BTB
3.152+ 0.3SLX
181.577
+ 0.3SLY + 38.678
1SLZ + 1.1NLB
Min My 25879 1054 1DL24749
+ 1SIDL 2247.833
+ 0.3CL + 0.3PLA
-16.91
+ 0.33TLA
-58.606
- 0.33BTA
-3.685
- 0.3SLX
-178.794
- 0.3SLY - 1SLZ
-52.189
Max Mz 25879 1007 1DL24749
+ 1SIDL +2437.82
1SLX + 0.3SLY47.82
+ 0.3SLZ 21.718 4.202 62.794 147.639
Min Mz 25912 1152 1DL24782
+ 1SIDL 2355.586
- 1COL(-X)-MLC
-69.948 0.32 1.275 0.996 -258.613

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 25945 2106 1.15DL
24815
+ 1.2SIDL
4307.411
+ 1.4CL + 1.4PLA
4.917 + 1.4PLB
1.353+ 1.54TLA
-1.462
+ 1.54TLB
-2.578
- 1.54BTA
15.349
- 1.54BTB
Min Fx 25978 2107 1.15DL
24849
+ 1.2SIDL
2238.501
+ 1SLX +-63.563
0.3SLY + 0.3SLZ
-25.279 -6.878 -50.855 -130.494
Max Fy 25945 2104 1.15DL
24815
+ 1.2SIDL
4283.873
+ 1.4CL +95.919
1.4PLB + 1.54TLB
10.26 - 1.54BTB
7.844 29.067 294.363
Min Fy 25912 1452 1.15DL
24782
+ 1.2SIDL
2667.677
- 1.5COL(-X)-MLC
-104.198 0.622 2.06 0.44 -385.655
Max Fz 25879 3147 1.15DL
24749
+ 1.2SIDL
3121.841
+ 0.42CL16.335
+ 0.42PLA +75.884
0.462TLA +3.694
0.462BTA
218.303
+ 0.3SLX 51.433
+ 0.3SLY + 1SLZ + 1.5
Min Fz 25912 3171 1.15DL
24783
+ 1.2SIDL
2826.232
+ 0.42CL-23.547
+ 0.42PLB +-75.687
0.462TLB-4.505
+ 0.462BTB
-143.105
+ 0.3SLX-49.255
+ 0.3SLY + 1SLZ + 1.
Max Mx 25978 2103 1.15DL
24848
+ 1.2SIDL
3990.5
+ 1.4CL +86.429
1.4PLB + 1.54TLB
6.363 + 1.54BTB
9.104 17.235 263.743
Min Mx 25945 2104 1.15DL
24816
+ 1.2SIDL
4177.714
+ 1.4CL -93.647
+ 1.4PLB + 1.54TLB
-9.362 - 1.54BTB
-9.632 -19.094 -192.605
Max My 25912 1453 1.15DL
24782
+ 1.2SIDL
2859.556
+ 1.5COL(Z)-MLC
-2.164 -65.165 -1.283 229.456 -6.736
Min My 25879 2154 1.15DL
24749
+ 1.2SIDL
2612.367
+ 0.42CL-20.944
+ 0.42PLA +-73.583
0.462TLA-4.609
- 0.462BTA
-224.345
- 0.3SLX --64.626
0.3SLY - 1SLZ
Max Mz 25945 2104 1.15DL
24815
+ 1.2SIDL
4283.873
+ 1.4CL +95.919
1.4PLB + 1.54TLB
10.26 - 1.54BTB
7.844 29.067 294.363
Min Mz 25912 1452 1.15DL
24782
+ 1.2SIDL
2667.677
- 1.5COL(-X)-MLC
-104.198 0.622 2.06 0.44 -385.655

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 2668 385.7 1293 0.298 OK
Minima 4307 15.6 1572 0.010 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 37.53 OK
Minima 7.031 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.616 OK 32.79 OK
Minima 3.377 OK 24.4 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.7645 m
Hence de = 0.743 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 566 kN
Corresponding axial compressive force, N = 2668 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 4536 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0023 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.339 %
Horizontal shear force, Vu = 566 kN
Shear stress (vv = Vu /(bv . dv) = 845.84 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.515 Mpa
= 515 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 478.933 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.17
Modified shear strength of concrete (n s vc ) = 560.27 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 191.05 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.61 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C32


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C32

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 4
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31519 1005 1DL30575
+ 1SIDL 5188.017
+ 1CL + 1PLA +97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB
-0.255
+ 1.1BTA149.808
+ 1.1BTB 440.298
Min Fx 31520 1001 1DL30576
+ 1SIDL 3576.077
+ 1CL + 1PLA +41.983
1.1TLA + 1.1BTA
12.61 -0.223 -129.703 103.922
Max Fy 31519 1005 1DL30575
+ 1SIDL 5188.017
+ 1CL + 1PLA +97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB
-0.255
+ 1.1BTA149.808
+ 1.1BTB 440.298
Min Fy 31518 1006 1DL30574
+ 1SIDL 4920.688
+ 1CL + 1PLA +-45.07
1PLB + 1.1TLA
-35.57
+ 1.1TLB
-2.255
- 1.1BTA203.104
- 1.1BTB -242.084
Max Fz 31525 1001 1DL30581
+ 1SIDL 4264.383
+ 1CL + 1PLA +61.129
1.1TLA + 13.795
1.1BTA -0.222 -124.555 253.815
Min Fz 31518 1006 1DL30574
+ 1SIDL 4920.688
+ 1CL + 1PLA +-45.07
1PLB + 1.1TLA
-35.57
+ 1.1TLB
-2.255
- 1.1BTA203.104
- 1.1BTB -242.084
Max Mx 31521 1005 1DL30577
+ 1SIDL 5039.345
+ 1CL + 1PLA +96.812
1PLB + 1.1TLA
10.731
+ 1.1TLB
-0.087
+ 1.1BTA
-119.281
+ 1.1BTB 437.954
Min Mx 31520 1006 1DL30576
+ 1SIDL 4635.832
+ 1CL + 1PLA -44.607
+ 1PLB + 1.1TLA
-3.854
+ 1.1TLB
-2.316
- 1.1BTA -57.587
- 1.1BTB -238.309
Max My 31518 1004 1DL30574
+ 1SIDL +4121.32
1CL + 1PLB -14.089
+ 1.1TLB - 1.1BTB
-33.7 -1.545 204.457 -112.033
Min My 31521 1001 1DL30577
+ 1SIDL 4264.383
+ 1CL + 1PLA +68.555
1.1TLA + 13.655
1.1BTA -0.222 -138.21 322.369
Max Mz 31519 1005 1DL30575
+ 1SIDL 5188.017
+ 1CL + 1PLA +97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB
-0.255
+ 1.1BTA149.808
+ 1.1BTB 440.298
Min Mz 31518 1006 1DL30574
+ 1SIDL 4920.688
+ 1CL + 1PLA +-45.07
1PLB + 1.1TLA
-35.57
+ 1.1TLB
-2.255
- 1.1BTA203.104
- 1.1BTB -242.084

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31519 1095 1DL30575
+ 1SIDL 8708.132
+ 0.3CL + 0.3PLA
241.483
+ 0.3PLB721.159
+ 0.33TLA +6.908
0.33TLB3124.196
+ 0.33BTA +1046.587
0.33BTB + 0.3SLX + 0.
Min Fx 31520 1015 1DL30580
+ 1SIDL-1515.166
+ 0.3SLX + 0.3SLY
-179.697
+ 1SLZ-738.489 -8.744 -2317.093 -620.611
Max Fy 31519 1079 1DL30575
+ 1SIDL + 0.3CL
8256.9
+ 0.3PLA
636.375
+ 0.3PLB272.118
+ 0.33TLA 10.581
+ 0.33TLB1314.209
+ 0.33BTA +2633.449
0.33BTB + 1SLX + 0.3S
Min Fy 31520 1086 1DL30576
+ 1SIDL +-617.862
0.3CL + 0.3PLA-591
+ 0.3PLB
-291.416
+ 0.33TLA-13.006
+ 0.33TLB-1249.102
- 0.33BTA -2456.136
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 31520 3054 1DL30580
+ 1SIDL 8110.168
+ 0.3CL + 0.3PLA
193.087
+ 0.33TLA
751.692
- 0.33BTA7.309
- 0.3SLX
2165.382
- 0.3SLY - 1SLZ
563.121
- 1.1NLA
Min Fz 31519 3078 1DL30575
+ 1SIDL + -878.66
0.3CL + 0.3PLB
-163.46
+ 0.33TLB
-771.987
- 0.33BTB
-9.164
- 0.3SLX
-2823.844
- 0.3SLY - -637.381
1SLZ - 1.1NLB
Max Mx 31520 3055 1DL30576
+ 1SIDL 7601.907
+ 0.3CL + 0.3PLB
604.305
+ 0.33TLB
300.798
+ 0.33BTB
11.398
+ 1SLX
1104.168
+ 0.3SLY +2404.631
0.3SLZ + 1.1NLB
Min Mx 31520 3062 1DL30576
+ 1SIDL +-832.948
0.3CL + 0.3PLB
-582.018
+ 0.33TLB
-299.423
- 0.33BTB
-13.298
- 1SLX-1209.14
- 0.3SLY - 0.3SLZ
-2418.799
- 1.1NLB
Max My 31519 3047 1DL30575
+ 1SIDL 8558.558
+ 0.3CL + 0.3PLA
232.955
+ 0.33TLA
716.121
+ 0.33BTA6.376
+ 0.3SLX
3136.29
+ 0.3SLY1012.387
+ 1SLZ + 1.1NLA
Min My 31520 3054 1DL30576
+ 1SIDL-1261.682
+ 0.3CL + 0.3PLA
-186.597
+ 0.33TLA
-731.043
- 0.33BTA
-8.488
- 0.3SLX
-3099.512
- 0.3SLY --829.803
1SLZ - 1.1NLA
Max Mz 31519 1079 1DL30575
+ 1SIDL + 0.3CL
8256.9
+ 0.3PLA
636.375
+ 0.3PLB272.118
+ 0.33TLA 10.581
+ 0.33TLB1314.209
+ 0.33BTA +2633.449
0.33BTB + 1SLX + 0.3S
Min Mz 31520 1086 1DL30576
+ 1SIDL +-617.862
0.3CL + 0.3PLA-591
+ 0.3PLB
-291.416
+ 0.33TLA-13.006
+ 0.33TLB-1249.102
- 0.33BTA -2456.136
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.144
+ 1.4CL
1204.986
+ 1.4PLB + 118.746
1.54TLB + 18.186
1.54BTB 754.235 4928.127
Min Fx 31520 2103 1.15DL
30580
+ 1.2SIDL
-2223.055
+ 1.4CL-1057.58
+ 1.4PLB + -142.058
1.54TLB + -20.528
1.54BTB -512.402 -3298.257
Max Fy 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.144
+ 1.4CL
1204.986
+ 1.4PLB + 118.746
1.54TLB + 18.186
1.54BTB 754.235 4928.127
Min Fy 31520 2104 1.15DL
30580
+ 1.2SIDL
-1753.614
+ 1.4CL-1134.85
+ 1.4PLB + -147.484
1.54TLB - -21.511
1.54BTB -498.366 -3516.416
Max Fz 31520 3154 1.15DL
30580
+ 1.2SIDL
9899.423
+ 0.42CL240.181
+ 0.42PLA 944.294
+ 0.462TLA -9.294
0.462BTA
2718.694
- 0.3SLX 704.266
- 0.3SLY - 1SLZ - 1.54N
Min Fz 31519 3178 1.15DL
30575
+ 1.2SIDL
-1435.858
+ 0.42CL
-209.395
+ 0.42PLB-968.667
+ 0.462TLB-11.508
- 0.462BTB
-3547.731
- 0.3SLX-820.384
- 0.3SLY - 1SLZ - 1.54N
Max Mx 31520 2103 1.15DL
30576
+ 1.2SIDL
9700.8
+ 1.4CL
1176.938
+ 1.4PLB + 146.984
1.54TLB + 19.087
1.54BTB 523.063 4697.542
Min Mx 31520 2104 1.15DL
30580
+ 1.2SIDL
-1753.614
+ 1.4CL-1134.85
+ 1.4PLB + -147.484
1.54TLB - -21.511
1.54BTB -498.366 -3516.416
Max My 31519 3147 1.15DL
30575
+ 1.2SIDL
10431.608
+ 0.42CL290.596
+ 0.42PLA 899.924
+ 0.462TLA + 8.04
0.462BTA
3927.081
+ 0.3SLX1258.742
+ 0.3SLY + 1SLZ + 1.5
Min My 31520 3154 1.15DL
30576
+ 1.2SIDL
-1865.348
+ 0.42CL
-236.384
+ 0.42PLA-916.718
+ 0.462TLA-10.524
- 0.462BTA
-3889.028
- 0.3SLX-1045.352
- 0.3SLY - 1SLZ - 1.54N
Max Mz 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.144
+ 1.4CL
1204.986
+ 1.4PLB + 118.746
1.54TLB + 18.186
1.54BTB 754.235 4928.127
Min Mz 31520 2104 1.15DL
30580
+ 1.2SIDL
-1753.614
+ 1.4CL-1134.85
+ 1.4PLB + -147.484
1.54TLB - -21.511
1.54BTB -498.366 -3516.416

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 5188.017 3576.077 9575.000 OK
ODE Seismic 8708.132 -1515.166 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Eff. N M Mu M/Mu Governing Neutral Neutral M/Mu
[kN] [kNm] [kNm]
Maxima 10700 4986 6517 0.765 OK
Minima 9899 2808 6567 0.428 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 142.1 OK
Minima -294.8 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


ase Bar Coordinates Notes
[N/mm²] [N/mm²]
Maxima 5.936 OK 38.94 OK
Minima 1.457 OK 13.02 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 19.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31561 1005 1DL30620
+ 1SIDL 5188.017
+ 1CL + 1PLA -15.065
+ 1PLB + 1.1TLA
2.669
+ 1.1TLB
-0.255
+ 1.1BTA-16.802
+ 1.1BTB -71.842
Min Fx 31579 1001 1DL30638
+ 1SIDL 3576.077
+ 1CL + 1PLA +-7.806
1.1TLA + -0.873
1.1BTA -0.223 10.074 -30.175
Max Fy 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Min Fy 31561 1005 1DL30620
+ 1SIDL 5188.017
+ 1CL + 1PLA -15.065
+ 1PLB + 1.1TLA
2.669
+ 1.1TLB
-0.255
+ 1.1BTA-16.802
+ 1.1BTB -71.842
Max Fz 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Min Fz 31630 1001 1DL30689
+ 1SIDL 4264.383
+ 1CL + 1PLA +-7.973
1.1TLA + 1.1BTA
-1.43 -0.222 7.285 -21.748
Max Mx 31597 1005 1DL30656
+ 1SIDL 5039.345
+ 1CL + 1PLA -15.037
+ 1PLB + 1.1TLA
-0.61
+ 1.1TLB
-0.087
+ 1.1BTA +8.664
1.1BTB -71.619
Min Mx 31579 1006 1DL30638
+ 1SIDL 4635.832
+ 1CL + 1PLA + 6.383
1PLB + 1.1TLA1.72
+ 1.1TLB
-2.316
- 1.1BTA - -2.081
1.1BTB 33.374
Max My 31597 1001 1DL30656
+ 1SIDL 4264.383
+ 1CL + 1PLA -10.465
+ 1.1TLA + -0.979
1.1BTA -0.222 10.886 -50.841
Min My 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Max Mz 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Min Mz 31561 1005 1DL30620
+ 1SIDL 5188.017
+ 1CL + 1PLA -15.065
+ 1PLB + 1.1TLA
2.669
+ 1.1TLB
-0.255
+ 1.1BTA-16.802
+ 1.1BTB -71.842
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31561 1095 1DL30620
+ 1SIDL 8708.132
+ 0.3CL + 0.3PLA
22.762
+ 0.3PLB123.016
+ 0.33TLA +6.908
0.33TLB +529.457
0.33BTA + 101.279
0.33BTB + 0.3SLX + 0.
Min Fx 31579 1015 1DL30639
+ 1SIDL-1515.166
+ 0.3SLX + 0.3SLY
-32.86
+ 1SLZ-120.168 -8.744 -421.375 -113.869
Max Fy 31579 1086 1DL30639
+ 1SIDL 7838.425
+ 0.3CL + 0.3PLA
95.053
+ 0.3PLB48.144
+ 0.33TLA 10.434
+ 0.33TLB -169.378
0.33BTA - 0.33BTB
339.927- 1SLX - 0.3SLY
Min Fy 31561 1079 1DL30621
+ 1SIDL +-138.687
0.3CL + 0.3PLA
-102.518
+ 0.3PLB-44.843
+ 0.33TLA-11.955
+ 0.33TLB-179.992
+ 0.33BTA +-365.742
0.33BTB + 1SLX + 0.3S
Max Fz 31561 3078 1DL30621
+ 1SIDL +8419.39
0.3CL + 0.3PLB
26.933
+ 0.33TLB
124.738
- 0.33BTB
6.026
- 0.3SLX
405.377
- 0.3SLY - 1SLZ
92.947
- 1.1NLB
Min Fz 31579 3054 1DL30638
+ 1SIDL-1261.682
+ 0.3CL + 0.3PLA
-31.765
+ 0.33TLA
-121.256
- 0.33BTA
-8.488
- 0.3SLX
-536.592
- 0.3SLY --141.628
1SLZ - 1.1NLA
Max Mx 31579 3055 1DL30638
+ 1SIDL 7601.907
+ 0.3CL + 0.3PLB
90.805
+ 0.33TLB 46.76
+ 0.33BTB
11.398
+ 1SLX221.599
+ 0.3SLY + 0.3SLZ
415.997+ 1.1NLB
Min Mx 31579 3062 1DL30638
+ 1SIDL +-832.948
0.3CL + 0.3PLB
-95.985
+ 0.33TLB-45.498
- 0.33BTB
-13.298
- 1SLX-219.568
- 0.3SLY - 0.3SLZ
-431.304
- 1.1NLB
Max My 31579 3071 1DL30638
+ 1SIDL 8059.688
+ 0.3CL + 0.3PLB
26.499
+ 0.33TLB
119.818
+ 0.33BTB
7.577
+ 0.3SLX
551.558
+ 0.3SLY + 125.92
1SLZ + 1.1NLB
Min My 31561 3078 1DL30620
+ 1SIDL + -878.66
0.3CL + 0.3PLB
-34.04
+ 0.33TLB
-116.174
- 0.33BTB
-9.164
- 0.3SLX
-567.782
- 0.3SLY - -159.576
1SLZ - 1.1NLB
Max Mz 31579 1007 1DL30638
+ 1SIDL 7398.903
+ 1SLX + 0.3SLY92.428
+ 0.3SLZ 47.719 10.875 217.479 422.873
Min Mz 31561 1014 1DL30620
+ 1SIDL --622.506
1SLX - 0.3SLY
-99.372
- 0.3SLZ -44.89 -12.14 -229.269 -453.94

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31561 1005 1DL30620
+ 1SIDL 5188.017
+ 1CL + 1PLA -15.065
+ 1PLB + 1.1TLA
2.669
+ 1.1TLB
-0.255
+ 1.1BTA-16.802
+ 1.1BTB -71.842
Min Fx 31579 1001 1DL30638
+ 1SIDL 3576.077
+ 1CL + 1PLA +-7.806
1.1TLA + -0.873
1.1BTA -0.223 10.074 -30.175
Max Fy 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Min Fy 31561 1005 1DL30620
+ 1SIDL 5188.017
+ 1CL + 1PLA -15.065
+ 1PLB + 1.1TLA
2.669
+ 1.1TLB
-0.255
+ 1.1BTA-16.802
+ 1.1BTB -71.842
Max Fz 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Min Fz 31630 1001 1DL30689
+ 1SIDL 4264.383
+ 1CL + 1PLA +-7.973
1.1TLA + 1.1BTA
-1.43 -0.222 7.285 -21.748
Max Mx 31597 1005 1DL30656
+ 1SIDL 5039.345
+ 1CL + 1PLA -15.037
+ 1PLB + 1.1TLA
-0.61
+ 1.1TLB
-0.087
+ 1.1BTA +8.664
1.1BTB -71.619
Min Mx 31579 1006 1DL30638
+ 1SIDL 4635.832
+ 1CL + 1PLA + 6.383
1PLB + 1.1TLA1.72
+ 1.1TLB
-2.316
- 1.1BTA - -2.081
1.1BTB 33.374
Max My 31597 1001 1DL30656
+ 1SIDL 4264.383
+ 1CL + 1PLA -10.465
+ 1.1TLA + -0.979
1.1BTA -0.222 10.886 -50.841
Min My 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Max Mz 31543 1006 1DL30602
+ 1SIDL 4920.688
+ 1CL + 1PLA + 6.429
1PLB + 1.1TLA
4.894
+ 1.1TLB
-2.255
- 1.1BTA -26.747
- 1.1BTB 33.734
Min Mz 31561 1005 1DL30620
+ 1SIDL 5188.017
+ 1CL + 1PLA -15.065
+ 1PLB + 1.1TLA
2.669
+ 1.1TLB
-0.255
+ 1.1BTA-16.802
+ 1.1BTB -71.842

ODE MDE
Maximum Tension Force (kN) -1515.17 3576.077
Skin Friction (kN) 2904.67
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Eff. N M Mu M/Mu Governing Neutral Neutral M/Mu
[kN] [kNm] [kNm]
Maxima 0 73.79 885.4 0.083 OK
Minima 4921 43.06 2495 0.017 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 70.53 OK
Minima -216.4 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.9 OK 34.29 OK
Minima 2.904 OK 21.05 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.954 m
Hence de = 0.904 m and dv = 0.813 m
Horizontal resultant shear force at the section, Vu = 1211 kN
Corresponding axial compressive force, N = 10696 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 40212 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0201 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 2.060 %
Horizontal shear force, Vu = 1211 kN
Shear stress (vv = Vu /(bv . dv) = 1240.65 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.940 Mpa
= 940 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 832.311 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.47
Modified shear strength of concrete (n s vc ) = 1225.89 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 14.40 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.38 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 12.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31554 1005 1DL30613
+ 1SIDL 5188.017
+ 1CL + 1PLA + 1PLB
-1.86+ 1.1TLA
-2.822
+ 1.1TLB
-0.255
+ 1.1BTA-19.458
+ 1.1BTB -151.736
Min Fx 31572 1001 1DL30631
+ 1SIDL 3576.077
+ 1CL + 1PLA +-6.417
1.1TLA + 1.1BTA
4.466 -0.223 -1.984 -91.463
Max Fy 31554 1006 1DL30613
+ 1SIDL 4547.937
+ 1CL + 1PLA + 5.372
1PLB + 1.1TLA
-1.909
+ 1.1TLB
-2.215
- 1.1BTA -42.806
- 1.1BTB 44.599
Min Fy 31536 1005 1DL30595
+ 1SIDL 4141.595
+ 1CL + 1PLA +-8.777
1PLB + 1.1TLA
-2.475
+ 1.1TLB
-0.267
+ 1.1BTA-18.681
+ 1.1BTB -137.275
Max Fz 31572 1002 1DL30631
+ 1SIDL 3883.671
+ 1CL + 1PLA +-2.792
1.1TLA - 1.1BTA
5.069 -1.737 -18.172 6.897
Min Fz 31554 1003 1DL30613
+ 1SIDL 4428.214
+ 1CL + 1PLB +-0.464
1.1TLB + -3.006
1.1BTB -0.924 -30.035 -102.907
Max Mx 31590 1005 1DL30649
+ 1SIDL 5039.345
+ 1CL + 1PLA +-1.923
1PLB + 1.1TLA
4.379
+ 1.1TLB
-0.087
+ 1.1BTA +-4.353
1.1BTB -151.602
Min Mx 31572 1006 1DL30631
+ 1SIDL 4635.832
+ 1CL + 1PLA +-1.485
1PLB + 1.1TLA
4.947
+ 1.1TLB
-2.316
- 1.1BTA -28.474
- 1.1BTB 58.931
Max My 31590 1001 1DL30650
+ 1SIDL 4264.383
+ 1CL + 1PLA +-0.567
1.1TLA + 1.1BTA
4.691 -0.222 3.211 -103.125
Min My 31536 1006 1DL30596
+ 1SIDL 4920.688
+ 1CL + 1PLA +-1.585
1PLB + 1.1TLA
-2.033
+ 1.1TLB
-2.255
- 1.1BTA -45.115
- 1.1BTB 60.737
Max Mz 31536 1006 1DL30596
+ 1SIDL 4920.688
+ 1CL + 1PLA +-1.585
1PLB + 1.1TLA
-2.033
+ 1.1TLB
-2.255
- 1.1BTA -45.115
- 1.1BTB 60.737
Min Mz 31554 1005 1DL30613
+ 1SIDL 5188.017
+ 1CL + 1PLA + 1PLB
-1.86+ 1.1TLA
-2.822
+ 1.1TLB
-0.255
+ 1.1BTA-19.458
+ 1.1BTB -151.736

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31554 1095 1DL30613
+ 1SIDL 8708.132
+ 0.3CL + 0.3PLA
10.065
+ 0.3PLB +36.17
0.33TLA +6.908
0.33TLB1247.182
+ 0.33BTA + 242.678
0.33BTB + 0.3SLX + 0.
Min Fx 31572 1015 1DL30632
+ 1SIDL-1515.166
+ 0.3SLX + 0.3SLY
-13.423
+ 1SLZ -34.959 -8.744 -1237.021 -337.453
Max Fy 31590 1086 1DL30650
+ 1SIDL 7616.492
+ 0.3CL + 0.3PLA
32.331
+ 0.3PLB19.142
+ 0.33TLA 10.288
+ 0.33TLB -469.931
0.33BTA - 0.33BTB
946.529- 1SLX - 0.3SLY
Min Fy 31536 1079 1DL30596
+ 1SIDL +-396.901
0.3CL + 0.3PLA
-35.139
+ 0.3PLB-17.243
+ 0.33TLA-12.148
+ 0.33TLB-503.796
+ 0.33BTA-1022.831
+ 0.33BTB + 1SLX + 0.3S
Max Fz 31590 3047 1DL30649
+ 1SIDL 8170.462
+ 0.3CL + 0.3PLA11.01
+ 0.33TLA 42.448
+ 0.33BTA
6.532
+ 0.3SLX
1246.965
+ 0.3SLY 254.156
+ 1SLZ + 1.1NLA
Min Fz 31536 3071 1DL30596
+ 1SIDL-1119.553
+ 0.3CL + 0.3PLB
-14.866
+ 0.33TLB-40.691
+ 0.33BTB
-8.199
+ 0.3SLX
-1242.085
+ 0.3SLY-349.561
+ 1SLZ + 1.1NLB
Max Mx 31572 3055 1DL30631
+ 1SIDL 7601.907
+ 0.3CL + 0.3PLB
25.153
+ 0.33TLB 17.616
+ 0.33BTB
11.398
+ 1SLX498.101
+ 0.3SLY + 0.3SLZ
945.699+ 1.1NLB
Min Mx 31572 3062 1DL30631
+ 1SIDL +-832.948
0.3CL + 0.3PLB
-33.06
+ 0.33TLB-11.232
- 0.33BTB
-13.298
- 1SLX-525.482
- 0.3SLY - 0.3SLZ
-1014.991
- 1.1NLB
Max My 31572 3071 1DL30631
+ 1SIDL 8059.688
+ 0.3CL + 0.3PLB5.259
+ 0.33TLB 40.904
+ 0.33BTB
7.577
+ 0.3SLX
1267.531
+ 0.3SLY + 267.88
1SLZ + 1.1NLB
Min My 31554 3078 1DL30613
+ 1SIDL + -878.66
0.3CL + 0.3PLB
-7.962
+ 0.33TLB-39.732
- 0.33BTB
-9.164
- 0.3SLX
-1305.715
- 0.3SLY - -348.034
1SLZ - 1.1NLB
Max Mz 31572 1086 1DL30632
+ 1SIDL 7838.425
+ 0.3CL + 0.3PLA
26.669
+ 0.3PLB18.607
+ 0.33TLA 10.434
+ 0.33TLB -471.364
0.33BTA - 0.33BTB
964.877- 1SLX - 0.3SLY
Min Mz 31554 1079 1DL30614
+ 1SIDL +-138.687
0.3CL + 0.3PLA
-29.403
+ 0.3PLB-16.876
+ 0.33TLA-11.955
+ 0.33TLB-505.799
+ 0.33BTA-1041.576
+ 0.33BTB + 1SLX + 0.3S
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31554 2103 1.15DL
30613
+ 1.2SIDL
10696.144
+ 1.4CL +55.276
1.4PLB + 1.54TLB
4.584 + 18.186
1.54BTB 219.121 1771.557
Min Fx 31572 2103 1.15DL
30632
+ 1.2SIDL
-2223.055
+ 1.4CL -64.271
+ 1.4PLB + 1.54TLB
-3.486 + -20.528
1.54BTB -247.811 -1966.594
Max Fy 31590 2104 1.15DL
30649
+ 1.2SIDL
9578.835
+ 1.4CL +60.418
1.4PLB + 1.54TLB
12.175 - 1.54BTB
17.913 220.003 1908.52
Min Fy 31536 2103 1.15DL
30596
+ 1.2SIDL
-1626.921
+ 1.4CL -64.467
+ 1.4PLB + 1.54TLB
-10.416 + -20.148
1.54BTB -263.154 -1965.959
Max Fz 31590 3147 1.15DL
30649
+ 1.2SIDL
9943.603
+ 0.42CL13.639
+ 0.42PLA +53.072
0.462TLA +8.234
0.462BTA
1564.917
+ 0.3SLX320.937
+ 0.3SLY + 1SLZ + 1.5
Min Fz 31536 3171 1.15DL
30596
+ 1.2SIDL
-1727.365
+ 0.42CL-18.404
+ 0.42PLB + -51.04
0.462TLB
-10.121
+ 0.462BTB
-1555.499
+ 0.3SLX-438.294
+ 0.3SLY + 1SLZ + 1.5
Max Mx 31572 2103 1.15DL
30631
+ 1.2SIDL
9700.8
+ 1.4CL +49.043
1.4PLB + 1.54TLB
10.782 + 19.087
1.54BTB 232.114 1784.588
Min Mx 31572 2104 1.15DL
30632
+ 1.2SIDL
-1753.614
+ 1.4CL -59.224
+ 1.4PLB + 1.54TLB
-3.048 - -21.511
1.54BTB -257.391 -1834.469
Max My 31572 3171 1.15DL
30631
+ 1.2SIDL
9828.751
+ 0.42CL + 0.42PLB
6.85 +50.954
0.462TLB +9.67
0.462BTB
1593.704
+ 0.3SLX337.205
+ 0.3SLY + 1SLZ + 1.5
Min My 31554 3178 1.15DL
30613
+ 1.2SIDL
-1435.858
+ 0.42CL-10.024
+ 0.42PLB +-49.703
0.462TLB
-11.508
- 0.462BTB
-1639.386
- 0.3SLX-430.851
- 0.3SLY - 1SLZ - 1.54N
Max Mz 31572 2104 1.15DL
30631
+ 1.2SIDL
10170.241
+ 1.4CL + 1.4PLB
54.09 + 1.54TLB
11.219 - 1.54BTB
18.104 222.096 1921.759
Min Mz 31554 2103 1.15DL
30614
+ 1.2SIDL
-1156.056
+ 1.4CL -58.096
+ 1.4PLB + 1.54TLB
-9.697 + -19.884
1.54BTB -266.948 -1985.676

ODE MDE
Maximum Tension Force (kN) -1515.17 -2223.06
Skin Friction (kN) 1110.67
Final Axial Load (kN) -404.50 -1112.39

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


40 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -1112 1982 2865 0.692 OK
Minima 9944 1597 4532 0.353 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 86.36 OK
Minima -195.9 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.934 OK 33.97 OK
Minima 2.373 OK 17.71 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C33


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C33

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26779 1002 1DL25729
+ 1SIDL 3671.011
+ 1CL + 1PLA +-0.593
1.1TLA - -0.471
1.1BTA -0.78 -32.612 0.457
Min Fx 26779 1005 1DL25729
+ 1SIDL 3630.198
+ 1CL + 1PLA +13.848
1PLB + 1.1TLA
2.337
+ 1.1TLB
-0.043
+ 1.1BTA-16.206
+ 1.1BTB -68.356
Max Fy 26808 1005 1DL25728
+ 1SIDL 3630.198
+ 1CL + 1PLA +37.437
1PLB + 1.1TLA
2.144
+ 1.1TLB
-0.043
+ 1.1BTA-23.005
+ 1.1BTB 17.971
Min Fy 26808 1006 1DL25728
+ 1SIDL 3668.137
+ 1CL + 1PLA-13.422
+ 1PLB + 1.1TLA
-3.386
+ 1.1TLB
-0.973
- 1.1BTA-22.683
- 1.1BTB -6.72
Max Fz 26808 1003 1DL25728
+ 1SIDL 3649.374
+ 1CL + 1PLB +23.992
1.1TLB + 1.1BTB
4.625 -0.35 -24.263 9.684
Min Fz 26808 1002 1DL25728
+ 1SIDL 3671.011
+ 1CL + 1PLA +-1.231
1.1TLA - 1.1BTA
-5.83 -0.78 -21.195 -2.547
Max Mx 26779 1005 1DL25729
+ 1SIDL 3630.198
+ 1CL + 1PLA +13.848
1PLB + 1.1TLA
2.337
+ 1.1TLB
-0.043
+ 1.1BTA-16.206
+ 1.1BTB -68.356
Min Mx 26779 1006 1DL25729
+ 1SIDL 3668.137
+ 1CL + 1PLA +-4.984
1PLB + 1.1TLA
0.456
+ 1.1TLB
-0.973
- 1.1BTA-28.437
- 1.1BTB 24.253
Max My 26787 1003 1DL25738
+ 1SIDL 3649.374
+ 1CL + 1PLB +-6.514
1.1TLB + 1.1BTB
0.271 -0.35 4.521 -42.36
Min My 26779 1002 1DL25730
+ 1SIDL 3671.011
+ 1CL + 1PLA +-0.593
1.1TLA - -0.471
1.1BTA -0.78 -33.082 1.05
Max Mz 26782 1006 1DL25733
+ 1SIDL 3668.137
+ 1CL + 1PLA + 1PLB
-0.23 + 1.1TLA
2.176
+ 1.1TLB
-0.973
- 1.1BTA-22.806
- 1.1BTB 33.968
Min Mz 26782 1005 1DL25733
+ 1SIDL 3630.198
+ 1CL + 1PLA + 0.572
1PLB + 1.1TLA
2.046
+ 1.1TLB
-0.043
+ 1.1BTA +-7.384
1.1BTB -95.197

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26779 1002 1DL25729
+ 1SIDL 3671.011
+ 1CL + 1PLA +-0.593
1.1TLA - -0.471
1.1BTA -0.78 -32.612 0.457
Min Fx 26779 1023 1DL25730
+ 1SIDL 2867.963
+ 0.3SLX + 1SLY
-23.876
+ 0.3SLZ -33.709 -2.544 -229.652 -167.965
Max Fy 26808 1152 1DL25728
+ 1SIDL 3121.959
- 1COL(-X)-MLC
378.539 3.203 0.923 -18.716 830.468
Min Fy 26808 1086 1DL25728
+ 1SIDL 3132.212
+ 0.3CL + 0.3PLA
-223.513
+ 0.3PLB
-112.073
+ 0.33TLA -5.902
+ 0.33TLB --60.016
0.33BTA - -129.723
0.33BTB - 1SLX - 0.3SLY - 0.3SLZ
Max Fz 26808 3071 1DL25728
+ 1SIDL 3416.291
+ 0.3CL + 0.3PLB
84.138
+ 0.33TLB
273.685
+ 0.33BTB
3.43
+ 0.3SLX60.687
+ 0.3SLY +46.327
1SLZ + 1.1NLB
Min Fz 26808 3047 1DL25759
+ 1SIDL 3185.201
+ 0.3CL + 0.3PLA
-57.966
+ 0.33TLA
-272.713
+ 0.33BTA-4.14
+ 0.3SLX
-226.85
+ 0.3SLY -43.301
+ 1SLZ + 1.1NLA
Max Mx 26779 3055 1DL25729
+ 1SIDL 3474.033
+ 0.3CL + 0.3PLB
89.446
+ 0.33TLB43.036
+ 0.33BTB
5.184
+ 1SLX214.541
+ 0.3SLY + 369.734
0.3SLZ + 1.1NLB
Min Mx 26779 3062 1DL25729
+ 1SIDL 3132.395
+ 0.3CL + 0.3PLB
-82.912
+ 0.33TLB
-39.369
- 0.33BTB
-6.043
- 1SLX-246.031
- 0.3SLY - 0.3SLZ
-407.405
- 1.1NLB
Max My 26783 3071 1DL25733
+ 1SIDL 3416.291
+ 0.3CL + 0.3PLB
2.692
+ 0.33TLB22.007
+ 0.33BTB
3.43
+ 0.3SLX
714.094
+ 0.3SLY 141.959
+ 1SLZ + 1.1NLB
Min My 26781 3047 1DL25732
+ 1SIDL 3185.201
+ 0.3CL + 0.3PLA
-7.083
+ 0.33TLA
-23.114
+ 0.33BTA-4.14
+ 0.3SLX
-737.607
+ 0.3SLY -209.44
+ 1SLZ + 1.1NLA
Max Mz 26808 1152 1DL25728
+ 1SIDL 3121.959
- 1COL(-X)-MLC
378.539 3.203 0.923 -18.716 830.468
Min Mz 26785 1152 1DL25736
+ 1SIDL 3121.959
- 1COL(-X)-MLC4.646 1.086 0.923 1.846 -647.031
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26779 2104 1.15DL
25729
+ 1.2SIDL
4476.426
+ 1.4CL160.797
+ 1.4PLB + 1.54TLB
24.476 - 1.54BTB
8.181 98.501 764.261
Min Fx 26779 2123 1.15DL
25730
+ 1.2SIDL
3289.247
+ 0.3SLX-30.229
+ 1SLY + 0.3SLZ
-42.154 -3.144 -286.133 -208.755
Max Fy 26808 1452 1.15DL
25728
+ 1.2SIDL
3581.804
- 1.5COL(-X)-MLC
564.874 4.762 1.524 -21.594 1245.075
Min Fy 26808 2104 1.15DL
25759
+ 1.2SIDL
4114.605
+ 1.4CL-437.192
+ 1.4PLB + -60.542
1.54TLB - 1.54BTB
-9.824 -70.886 -196.193
Max Fz 26808 3171 1.15DL
25728
+ 1.2SIDL
3973.134
+ 0.42CL105.473
+ 0.42PLB 344.081
+ 0.462TLB4.378
+ 0.462BTB
77.084
+ 0.3SLX 58.065
+ 0.3SLY + 1SLZ + 1.54NLB
Min Fz 26808 3147 1.15DL
25759
+ 1.2SIDL
3696.849
+ 0.42CL-73.029
+ 0.42PLA +-342.78
0.462TLA-5.172
+ 0.462BTA
-282.96
+ 0.3SLX-53.824
+ 0.3SLY + 1SLZ + 1.54NLA
Max Mx 26779 2103 1.15DL
25729
+ 1.2SIDL
4449.967
+ 1.4CL173.961
+ 1.4PLB + 1.54TLB
25.248 + 1.54BTB
8.596 103.557 699.549
Min Mx 26779 2104 1.15DL
25730
+ 1.2SIDL
4114.605
+ 1.4CL-164.367
+ 1.4PLB + -19.701
1.54TLB - 1.54BTB
-9.824 -165.581 -916.408
Max My 26783 3171 1.15DL
25733
+ 1.2SIDL
3973.134
+ 0.42CL + 0.42PLB
3.4 +27.369
0.462TLB4.378
+ 0.462BTB
899.235
+ 0.3SLX179.103
+ 0.3SLY + 1SLZ + 1.54NLB
Min My 26781 3147 1.15DL
25732
+ 1.2SIDL
3696.849
+ 0.42CL -8.877
+ 0.42PLA +-29.147
0.462TLA-5.172
+ 0.462BTA
-926.302
+ 0.3SLX-262.455
+ 0.3SLY + 1SLZ + 1.54NLA
Max Mz 26808 1452 1.15DL
25728
+ 1.2SIDL
3581.804
- 1.5COL(-X)-MLC
564.874 4.762 1.524 -21.594 1245.075
Min Mz 26782 2103 1.15DL
25733
+ 1.2SIDL
4088.146
+ 1.4CL +-9.857
1.4PLB + 1.54TLB
1.814 + 1.54BTB
-9.409 -170.102 -1163.304

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 3671.011 3630.198 7790.000 OK
ODE Seismic 3671.011 2867.963 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


1st Layer 16 16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 3582 1245 1465 0.850 OK
Minima 3973 96.51 1526 0.063 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 77.52 OK
Minima -33.77 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.401 OK 36.93 OK
Minima 3.527 OK 26.84 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.766 m
Hence de = 0.744 m and dv = 0.669 m
Horizontal resultant shear force at the section, Vu = 565 kN
Corresponding axial compressive force, N = 3582 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 3217 mm2
Effective area of tensile steel = 50% of total steel = As = 0.0016 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.240 %
Horizontal shear force, Vu = 565 kN
Shear stress (vv = Vu /(bv . dv) = 843.83 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
1/3 1/3
vc = 0.27/ m (100As/(bd)) (fcu) (where m = 1.25) = 0.459 Mpa
= 459 kN/m2
1/4
Depth Factor, s = (500/d) or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 426.930 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/Ac) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.23
Modified shear strength of concrete (n s vc ) = 524.28 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 213.92 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.78 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C34


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C34

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 4
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30339 1005 1DL29383
+ 1SIDL 4612.376
+ 1CL + 1PLA +93.247
1PLB + 1.1TLA
-9.834
+ 1.1TLB
-0.473
+ 1.1BTA +80.393
1.1BTB 414.166
Min Fx 30340 1001 1DL29384
+ 1SIDL 3049.483
+ 1CL + 1PLA +46.065
1.1TLA + 12.309
1.1BTA -0.07 -123.659 130.658
Max Fy 30339 1005 1DL29383
+ 1SIDL 4612.376
+ 1CL + 1PLA +93.247
1PLB + 1.1TLA
-9.834
+ 1.1TLB
-0.473
+ 1.1BTA +80.393
1.1BTB 414.166
Min Fy 30338 1006 1DL29382
+ 1SIDL 4359.919
+ 1CL + 1PLA -36.022
+ 1PLB + 1.1TLA
-28.561
+ 1.1TLB
-2.367
- 1.1BTA -153.81
1.1BTB -188.831
Max Fz 30341 1005 1DL29385
+ 1SIDL 4432.949
+ 1CL + 1PLA +92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB
-0.309
+ 1.1BTA
-152.627
+ 1.1BTB 410.439
Min Fz 30338 1006 1DL29382
+ 1SIDL 4359.919
+ 1CL + 1PLA -36.022
+ 1PLB + 1.1TLA
-28.561
+ 1.1TLB
-2.367
- 1.1BTA -153.81
1.1BTB -188.831
Max Mx 30340 1001 1DL29384
+ 1SIDL 3049.483
+ 1CL + 1PLA +46.065
1.1TLA + 12.309
1.1BTA -0.07 -123.659 130.658
Min Mx 30340 1006 1DL29384
+ 1SIDL 3984.184
+ 1CL + 1PLA -35.307
+ 1PLB + 1.1TLA-1.35
+ 1.1TLB
-2.413
- 1.1BTA -69.863
- 1.1BTB -182.972
Max My 30338 1006 1DL29382
+ 1SIDL 4359.919
+ 1CL + 1PLA -36.022
+ 1PLB + 1.1TLA
-28.561
+ 1.1TLB
-2.367
- 1.1BTA -153.81
1.1BTB -188.831
Min My 30341 1005 1DL29385
+ 1SIDL 4432.949
+ 1CL + 1PLA +92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB
-0.309
+ 1.1BTA
-152.627
+ 1.1BTB 410.439
Max Mz 30339 1005 1DL29383
+ 1SIDL 4612.376
+ 1CL + 1PLA +93.247
1PLB + 1.1TLA
-9.834
+ 1.1TLB
-0.473
+ 1.1BTA +80.393
1.1BTB 414.166
Min Mz 30338 1006 1DL29382
+ 1SIDL 4359.919
+ 1CL + 1PLA -36.022
+ 1PLB + 1.1TLA
-28.561
+ 1.1TLB
-2.367
- 1.1BTA -153.81
1.1BTB -188.831

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30339 1095 1DL29383
+ 1SIDL +8283.47
0.3CL + 0.3PLA
239.545
+ 0.3PLB743.771
+ 0.33TLA +6.819
0.33TLB3171.188
+ 0.33BTA +1034.292
0.33BTB + 0.3SLX + 0.
Min Fx 30340 1015 1DL29388
+ 1SIDL-1862.736
+ 0.3SLX + 0.3SLY
-172.69
+ 1SLZ-755.944 -8.965 -2377.889 -589.815
Max Fy 30339 1079 1DL29383
+ 1SIDL 7887.372
+ 0.3CL + 0.3PLA
631.035
+ 0.3PLB308.488
+ 0.33TLA 10.536
+ 0.33TLB1408.363
+ 0.33BTA +2611.575
0.33BTB + 1SLX + 0.3S
Min Fy 30340 1086 1DL29384
+ 1SIDL +-965.669
0.3CL + 0.3PLA
-578.782
+ 0.3PLB
-321.708
+ 0.33TLA-13.248
+ 0.33TLB-1377.918
- 0.33BTA -2397.059
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 30341 3071 1DL29385
+ 1SIDL 7850.396
+ 0.3CL + 0.3PLB
225.916
+ 0.33TLB
770.081
+ 0.33BTB
7.247
+ 0.3SLX
2977.688
+ 0.3SLY +964.288
1SLZ + 1.1NLB
Min Fz 30339 3078 1DL29383
+ 1SIDL-1313.841
+ 0.3CL + 0.3PLB
-158.88
+ 0.33TLB
-784.549
- 0.33BTB
-9.438
- 0.3SLX
-2940.151
- 0.3SLY - -622.354
1SLZ - 1.1NLB
Max Mx 30340 3055 1DL29384
+ 1SIDL 7004.733
+ 0.3CL + 0.3PLB
602.72
+ 0.33TLB
334.531
+ 0.33BTB
11.408
+ 1SLX
1221.221
+ 0.3SLY + 0.3SLZ
2410.17+ 1.1NLB
Min Mx 30340 3062 1DL29384
+ 1SIDL-1164.858
+ 0.3CL + 0.3PLB
-570.015
+ 0.33TLB
-328.896
- 0.33BTB
-13.675
- 1SLX
-1343.631
- 0.3SLY - 0.3SLZ
-2361.178
- 1.1NLB
Max My 30339 3047 1DL29383
+ 1SIDL 8165.646
+ 0.3CL + 0.3PLA
232.289
+ 0.33TLA
735.554
+ 0.33BTA6.349
+ 0.3SLX
3197.447
+ 0.3SLY1006.755
+ 1SLZ + 1.1NLA
Min My 30340 3054 1DL29384
+ 1SIDL-1636.839
+ 0.3CL + 0.3PLA
-178.525
+ 0.33TLA
-748.863
- 0.33BTA
-8.581
- 0.3SLX
-3173.338
- 0.3SLY --785.955
1SLZ - 1.1NLA
Max Mz 30339 1079 1DL29383
+ 1SIDL 7887.372
+ 0.3CL + 0.3PLA
631.035
+ 0.3PLB308.488
+ 0.33TLA 10.536
+ 0.33TLB1408.363
+ 0.33BTA +2611.575
0.33BTB + 1SLX + 0.3S
Min Mz 30340 1086 1DL29384
+ 1SIDL +-965.669
0.3CL + 0.3PLA
-578.782
+ 0.3PLB
-321.708
+ 0.33TLA-13.248
+ 0.33TLB-1377.918
- 0.33BTA -2397.059
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL
1196.044
+ 1.4PLB + 183.031
1.54TLB + 1.54BTB
17.56 931.72 4895.634
Min Fx 30340 2115 1.15DL
29388
+ 1.2SIDL
-2607.587
+ 0.3SLX
-218.375
+ 0.3SLY +-948.849
1SLZ -11.146 -2977.555 -740.725
Max Fy 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL
1196.044
+ 1.4PLB + 183.031
1.54TLB + 1.54BTB
17.56 931.72 4895.634
Min Fy 30340 2104 1.15DL
29388
+ 1.2SIDL
-2133.438
+ 1.4CL-1111.83
+ 1.4PLB + -201.934
1.54TLB - 1.54BTB
-22.36 -673.229 -3432.142
Max Fz 30341 3171 1.15DL
29385
+ 1.2SIDL
9605.008
+ 0.42CL281.439
+ 0.42PLB 967.533
+ 0.462TLB9.247
+ 0.462BTB
3736.262
+ 0.3SLX
1197.067
+ 0.3SLY + 1SLZ + 1.5
Min Fz 30339 3178 1.15DL
29383
+ 1.2SIDL
-1939.45
+ 0.42CL
-203.621
+ 0.42PLB-984.298
+ 0.462TLB-11.86
- 0.462BTB
-3692.205
- 0.3SLX-800.608
- 0.3SLY - 1SLZ - 1.54N
Max Mx 30340 2103 1.15DL
29384
+ 1.2SIDL
8853.004
+ 1.4CL
1170.858
+ 1.4PLB + 206.666
1.54TLB + 1.54BTB
18.57 733.089 4688.673
Min Mx 30340 2104 1.15DL
29388
+ 1.2SIDL
-2133.438
+ 1.4CL-1111.83
+ 1.4PLB + -201.934
1.54TLB - 1.54BTB
-22.36 -673.229 -3432.142
Max My 30339 3147 1.15DL
29383
+ 1.2SIDL
9979.791
+ 0.42CL289.404
+ 0.42PLA 923.846
+ 0.462TLA +8.014
0.462BTA
4005.073
+ 0.3SLX1250.205
+ 0.3SLY + 1SLZ + 1.5
Min My 30340 3154 1.15DL
29384
+ 1.2SIDL
-2291.332
+ 0.42CL
-226.544
+ 0.42PLA-938.936
+ 0.462TLA-10.609
- 0.462BTA
-3980.719
- 0.3SLX-991.998
- 0.3SLY - 1SLZ - 1.54N
Max Mz 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL
1196.044
+ 1.4PLB + 183.031
1.54TLB + 1.54BTB
17.56 931.72 4895.634
Min Mz 30340 2104 1.15DL
29388
+ 1.2SIDL
-2133.438
+ 1.4CL-1111.83
+ 1.4PLB + -201.934
1.54TLB - 1.54BTB
-22.36 -673.229 -3432.142

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 4612.376 3049.483 9575.000 OK
ODE Seismic 8283.47 -1862.736 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -2291 4102 5242 0.783 OK
Minima -2608 3068 5151 0.596 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 142.9 OK
Minima -310.5 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.317 OK 34.84 OK
Minima 1.172 OK 11.15 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 19.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30381 1005 1DL29428
+ 1SIDL 4612.376
+ 1CL + 1PLA -14.597
+ 1PLB + 1.1TLA
0.991
+ 1.1TLB
-0.473
+ 1.1BTA +-7.643
1.1BTB -68.904
Min Fx 30399 1001 1DL29446
+ 1SIDL 3049.483
+ 1CL + 1PLA +-8.316
1.1TLA + -0.896
1.1BTA -0.07 9.803 -33.28
Max Fy 30363 1006 1DL29410
+ 1SIDL 4359.919
+ 1CL + 1PLA + 5.208
1PLB + 1.1TLA
4.068
+ 1.1TLB
-2.367
- 1.1BTA -21.382
- 1.1BTB 26.914
Min Fy 30381 1005 1DL29428
+ 1SIDL 4612.376
+ 1CL + 1PLA -14.597
+ 1PLB + 1.1TLA
0.991
+ 1.1TLB
-0.473
+ 1.1BTA +-7.643
1.1BTB -68.904
Max Fz 30363 1006 1DL29410
+ 1SIDL 4359.919
+ 1CL + 1PLA + 5.208
1PLB + 1.1TLA
4.068
+ 1.1TLB
-2.367
- 1.1BTA -21.382
- 1.1BTB 26.914
Min Fz 30449 1005 1DL29469
+ 1SIDL 4432.949
+ 1CL + 1PLA -12.155
+ 1PLB + 1.1TLA
-2.056
+ 1.1TLB
-0.309
+ 1.1BTA +10.547
1.1BTB -40.559
Max Mx 30399 1001 1DL29446
+ 1SIDL 3049.483
+ 1CL + 1PLA +-8.316
1.1TLA + -0.896
1.1BTA -0.07 9.803 -33.28
Min Mx 30399 1006 1DL29446
+ 1SIDL 3984.184
+ 1CL + 1PLA + 5.136
1PLB + 1.1TLA
1.345
+ 1.1TLB
-2.413
- 1.1BTA - -0.219
1.1BTB 26.358
Max My 30417 1005 1DL29464
+ 1SIDL 4432.949
+ 1CL + 1PLA -14.552
+ 1PLB + 1.1TLA
-1.849
+ 1.1TLB
-0.309
+ 1.1BTA +14.411
1.1BTB -68.552
Min My 30363 1006 1DL29410
+ 1SIDL 4359.919
+ 1CL + 1PLA + 5.208
1PLB + 1.1TLA
4.068
+ 1.1TLB
-2.367
- 1.1BTA -21.382
- 1.1BTB 26.914
Max Mz 30363 1006 1DL29410
+ 1SIDL 4359.919
+ 1CL + 1PLA + 5.208
1PLB + 1.1TLA
4.068
+ 1.1TLB
-2.367
- 1.1BTA -21.382
- 1.1BTB 26.914
Min Mz 30381 1005 1DL29428
+ 1SIDL 4612.376
+ 1CL + 1PLA -14.597
+ 1PLB + 1.1TLA
0.991
+ 1.1TLB
-0.473
+ 1.1BTA +-7.643
1.1BTB -68.904
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30381 1095 1DL29428
+ 1SIDL +8283.47
0.3CL + 0.3PLA
22.342
+ 0.3PLB124.927
+ 0.33TLA +6.819
0.33TLB +546.341
0.33BTA + 0.33BTB
99.841 + 0.3SLX + 0.
Min Fx 30399 1015 1DL29447
+ 1SIDL-1862.736
+ 0.3SLX + 0.3SLY
-33.139
+ 1SLZ-122.714 -8.965 -431.729 -115.545
Max Fy 30399 1086 1DL29447
+ 1SIDL 7198.944
+ 0.3CL + 0.3PLA
93.237
+ 0.3PLB52.997
+ 0.33TLA 10.503
+ 0.33TLB -187.281
0.33BTA - 0.33BTB
332.665- 1SLX - 0.3SLY
Min Fy 30381 1079 1DL29429
+ 1SIDL +-661.424
0.3CL + 0.3PLA
-101.679
+ 0.3PLB-50.488
+ 0.33TLA-12.167
+ 0.33TLB-194.324
+ 0.33BTA +-362.654
0.33BTB + 1SLX + 0.3S
Max Fz 30381 3078 1DL29429
+ 1SIDL 8027.152
+ 0.3CL + 0.3PLB
26.145
+ 0.33TLB
126.823
- 0.33BTB5.83
- 0.3SLX
418.516
- 0.3SLY - 1SLZ
90.405
- 1.1NLB
Min Fz 30417 3071 1DL29465
+ 1SIDL-1252.088
+ 0.3CL + 0.3PLB
-36.097
+ 0.33TLB
-124.237
+ 0.33BTB
-8.188
+ 0.3SLX
-425.949
+ 0.3SLY-130.437
+ 1SLZ + 1.1NLB
Max Mx 30399 3055 1DL29446
+ 1SIDL 7004.733
+ 0.3CL + 0.3PLB
89.219
+ 0.33TLB 51.191
+ 0.33BTB
11.408
+ 1SLX246.413
+ 0.3SLY + 0.3SLZ
408.124+ 1.1NLB
Min Mx 30399 3062 1DL29446
+ 1SIDL-1164.858
+ 0.3CL + 0.3PLB
-95.777
+ 0.33TLB-50.619
- 0.33BTB
-13.675
- 1SLX --241.25
0.3SLY - 0.3SLZ
-431.302
- 1.1NLB
Max My 30417 3071 1DL29464
+ 1SIDL 7850.396
+ 0.3CL + 0.3PLB
22.897
+ 0.33TLB
121.804
+ 0.33BTB
7.247
+ 0.3SLX
566.514
+ 0.3SLY +100.572
1SLZ + 1.1NLB
Min My 30381 3078 1DL29428
+ 1SIDL-1313.841
+ 0.3CL + 0.3PLB
-34.168
+ 0.33TLB
-119.289
- 0.33BTB
-9.438
- 0.3SLX
-576.985
- 0.3SLY - -159.998
1SLZ - 1.1NLB
Max Mz 30399 1007 1DL29446
+ 1SIDL 6827.137
+ 1SLX + 0.3SLY90.796
+ 0.3SLZ 52.697 10.949 239.737 414.808
Min Mz 30381 1014 1DL29428
+ 1SIDL-1089.739
- 1SLX - 0.3SLY
-98.772
- 0.3SLZ -50.111 -12.313 -250.008 -451.254

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30381 2103 1.15DL
29428
+ 1.2SIDL
10293.99
+ 1.4CL165.827
+ 1.4PLB + 1.54TLB
34.672 + 1.54BTB
17.56 134.171 747.861
Min Fx 30399 2115 1.15DL
29447
+ 1.2SIDL
-2607.587
+ 0.3SLX-41.252
+ 0.3SLY +-154.055
1SLZ -11.146 -541.998 -144.054
Max Fy 30399 2104 1.15DL
29446
+ 1.2SIDL
9302.502
+ 1.4CL180.009
+ 1.4PLB + 1.54TLB
33.607 - 1.54BTB
17.689 146.613 817.488
Min Fy 30381 2103 1.15DL
29429
+ 1.2SIDL
-1852.168
+ 1.4CL-193.514
+ 1.4PLB + 1.54TLB
-30.225 + -20.764
1.54BTB -126.004 -686.01
Max Fz 30381 3178 1.15DL
29429
+ 1.2SIDL
9785.899
+ 0.42CL +33.46
0.42PLB 159.162
+ 0.462TLB7.288
- 0.462BTB
525.407
- 0.3SLX 115.942
- 0.3SLY - 1SLZ - 1.54N
Min Fz 30417 3171 1.15DL
29465
+ 1.2SIDL
-1822.08
+ 0.42CL-45.032
+ 0.42PLB-156.184
+ 0.462TLB-10.111
+ 0.462BTB
-533.994
+ 0.3SLX-162.388
+ 0.3SLY + 1SLZ + 1.5
Max Mx 30399 2103 1.15DL
29446
+ 1.2SIDL
8853.004
+ 1.4CL168.087
+ 1.4PLB + 1.54TLB
32.259 + 1.54BTB
18.57 152.551 765.425
Min Mx 30399 2104 1.15DL
29447
+ 1.2SIDL
-2133.438
+ 1.4CL-179.071
+ 1.4PLB + 1.54TLB
-31.244 - 1.54BTB
-22.36 -114.243 -628.804
Max My 30417 3171 1.15DL
29464
+ 1.2SIDL
9605.008
+ 0.42CL28.997
+ 0.42PLB 152.609
+ 0.462TLB9.247
+ 0.462BTB
711.708
+ 0.3SLX127.625
+ 0.3SLY + 1SLZ + 1.5
Min My 30381 3178 1.15DL
29428
+ 1.2SIDL
-1939.45
+ 0.42CL -42.23
+ 0.42PLB-149.722
+ 0.462TLB-11.86
- 0.462BTB
-723.853
- 0.3SLX-197.543
- 0.3SLY - 1SLZ - 1.54N
Max Mz 30399 2104 1.15DL
29446
+ 1.2SIDL
9302.502
+ 1.4CL180.009
+ 1.4PLB + 1.54TLB
33.607 - 1.54BTB
17.689 146.613 817.488
Min Mz 30381 2103 1.15DL
29429
+ 1.2SIDL
-1852.168
+ 1.4CL-193.514
+ 1.4PLB + 1.54TLB
-30.225 + -20.764
1.54BTB -126.004 -686.01

ODE MDE
Maximum Tension Force (kN) -1862.74 -2607.59
Skin Friction (kN) 2904.67
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 750.3 884.6 0.848 OK
Minima 9786 538 2997 0.180 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 69.1 OK
Minima -224.1 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.378 OK 30.68 OK
Minima 2.433 OK 17.67 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.954 m
Hence de = 0.904 m and dv = 0.813 m
Horizontal resultant shear force at the section, Vu = 1210 kN
Corresponding axial compressive force, N = 10294 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 40212 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0201 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 2.060 %
Horizontal shear force, Vu = 1210 kN
Shear stress (vv = Vu /(bv . dv) = 1239.77 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.940 Mpa
= 940 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 832.311 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.46
Modified shear strength of concrete (n s vc ) = 1211.09 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 27.99 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.38 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 12.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30374 1005 1DL29421
+ 1SIDL 4612.376
+ 1CL + 1PLA +-2.349
1PLB + 1.1TLA
-2.136
+ 1.1TLB
-0.473
+ 1.1BTA + 1.1BTB
-4.66 -148.312
Min Fx 30392 1001 1DL29439
+ 1SIDL 3049.483
+ 1CL + 1PLA +-5.961
1.1TLA + 1.1BTA
4.169 -0.07 -1.056 -95.384
Max Fy 30362 1006 1DL29409
+ 1SIDL 4359.919
+ 1CL + 1PLA + 5.291
1PLB + 1.1TLA
4.106
+ 1.1TLB
-2.367
- 1.1BTA -25.488
- 1.1BTB 32.205
Min Fy 30379 1005 1DL29426
+ 1SIDL 4612.376
+ 1CL + 1PLA -15.396
+ 1PLB + 1.1TLA
0.537
+ 1.1TLB
-0.473
+ 1.1BTA +-8.997
1.1BTB -99.621
Max Fz 30392 1002 1DL29439
+ 1SIDL 3328.963
+ 1CL + 1PLA +-2.237
1.1TLA - 1.1BTA
4.993 -1.553 -23.187 -3.04
Min Fz 30374 1003 1DL29421
+ 1SIDL +3933.48
1CL + 1PLB +-0.843
1.1TLB + -2.235
1.1BTB -1.408 -14.404 -104.919
Max Mx 30392 1001 1DL29439
+ 1SIDL 3049.483
+ 1CL + 1PLA +-5.961
1.1TLA + 1.1BTA
4.169 -0.07 -1.056 -95.384
Min Mx 30392 1006 1DL29439
+ 1SIDL 3984.184
+ 1CL + 1PLA +-0.808
1PLB + 1.1TLA
4.959
+ 1.1TLB
-2.413
- 1.1BTA -24.835
- 1.1BTB 48.335
Max My 30413 1005 1DL29461
+ 1SIDL 4432.949
+ 1CL + 1PLA -13.303
+ 1PLB + 1.1TLA0.51
+ 1.1TLB
-0.309
+ 1.1BTA +17.07
1.1BTB -113.756
Min My 30356 1006 1DL29404
+ 1SIDL 4359.919
+ 1CL + 1PLA +-0.964
1PLB + 1.1TLA
-1.03
+ 1.1TLB
-2.367
- 1.1BTA -38.397
- 1.1BTB 49.635
Max Mz 30356 1006 1DL29404
+ 1SIDL 4359.919
+ 1CL + 1PLA +-0.964
1PLB + 1.1TLA
-1.03
+ 1.1TLB
-2.367
- 1.1BTA -38.397
- 1.1BTB 49.635
Min Mz 30374 1005 1DL29421
+ 1SIDL 4612.376
+ 1CL + 1PLA +-2.349
1PLB + 1.1TLA
-2.136
+ 1.1TLB
-0.473
+ 1.1BTA + 1.1BTB
-4.66 -148.312

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30374 1095 1DL29421
+ 1SIDL +8283.47
0.3CL + 0.3PLA
9.641
+ 0.3PLB36.972
+ 0.33TLA +6.819
0.33TLB1278.184
+ 0.33BTA + 237.467
0.33BTB + 0.3SLX + 0.
Min Fx 30392 1015 1DL29440
+ 1SIDL-1862.736
+ 0.3SLX + 0.3SLY
-13.027
+ 1SLZ -35.322 -8.965 -1262.685 -339.598
Max Fy 30397 1086 1DL29445
+ 1SIDL 7198.944
+ 0.3CL + 0.3PLA
100.792
+ 0.3PLB +58.34
0.33TLA 10.503
+ 0.33TLB -293.638
0.33BTA - 0.33BTB
524.802- 1SLX - 0.3SLY
Min Fy 30379 1079 1DL29427
+ 1SIDL +-661.424
0.3CL + 0.3PLA
-109.938
+ 0.3PLB-55.287
+ 0.33TLA-12.167
+ 0.33TLB-306.023
+ 0.33BTA +-572.201
0.33BTB + 1SLX + 0.3S
Max Fz 30379 3078 1DL29427
+ 1SIDL 8027.152
+ 0.3CL + 0.3PLB
28.771
+ 0.33TLB
137.476
- 0.33BTB5.83
- 0.3SLX
664.899
- 0.3SLY - 1SLZ
144.481
- 1.1NLB
Min Fz 30415 3071 1DL29463
+ 1SIDL-1252.088
+ 0.3CL + 0.3PLB
-38.803
+ 0.33TLB
-134.453
+ 0.33BTB
-8.188
+ 0.3SLX
-677.629
+ 0.3SLY-204.594
+ 1SLZ + 1.1NLB
Max Mx 30392 3055 1DL29439
+ 1SIDL 7004.733
+ 0.3CL + 0.3PLB
25.539
+ 0.33TLB 18.728
+ 0.33BTB
11.408
+ 1SLX555.052
+ 0.3SLY + 0.3SLZ
930.42+ 1.1NLB
Min Mx 30392 3062 1DL29439
+ 1SIDL-1164.858
+ 0.3CL + 0.3PLB
-32.612
+ 0.33TLB-12.548
- 0.33BTB
-13.675
- 1SLX-575.215
- 0.3SLY - 0.3SLZ
-1011.231
- 1.1NLB
Max My 30410 3071 1DL29457
+ 1SIDL 7850.396
+ 0.3CL + 0.3PLB
10.595
+ 0.33TLB 41.14
+ 0.33BTB
7.247
+ 0.3SLX
1298.692
+ 0.3SLY +246.999
1SLZ + 1.1NLB
Min My 30374 3078 1DL29421
+ 1SIDL-1313.841
+ 0.3CL + 0.3PLB-8.19
+ 0.33TLB-39.185
- 0.33BTB
-9.438
- 0.3SLX
-1328.113
- 0.3SLY - -349.718
1SLZ - 1.1NLB
Max Mz 30392 1007 1DL29439
+ 1SIDL 6827.137
+ 1SLX + 0.3SLY26.38
+ 0.3SLZ 19.303 10.949 538.972 947.826
Min Mz 30374 1079 1DL29422
+ 1SIDL +-661.424
0.3CL + 0.3PLA
-29.57
+ 0.3PLB-17.618
+ 0.33TLA-12.167
+ 0.33TLB-550.083
+ 0.33BTA-1033.224
+ 0.33BTB + 1SLX + 0.3S
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30374 2103 1.15DL
29421
+ 1.2SIDL
10293.99
+ 1.4CL +54.497
1.4PLB + 1.54TLB
8.074 + 1.54BTB
17.56 322.646 1748.713
Min Fx 30392 2115 1.15DL
29440
+ 1.2SIDL
-2607.587
+ 0.3SLX-16.022
+ 0.3SLY + 1SLZ
-44.643 -11.146 -1583.971 -422.508
Max Fy 30397 2104 1.15DL
29444
+ 1.2SIDL
9302.502
+ 1.4CL195.394
+ 1.4PLB + 1.54TLB
37.296 - 1.54BTB
17.689 212.568 1204.187
Min Fy 30379 2103 1.15DL
29427
+ 1.2SIDL
-1852.168
+ 1.4CL-209.935
+ 1.4PLB + 1.54TLB
-33.339 + -20.764
1.54BTB -197.283 -1085.147
Max Fz 30379 3178 1.15DL
29427
+ 1.2SIDL
9785.899
+ 0.42CL36.779
+ 0.42PLB 172.575
+ 0.462TLB7.288
- 0.462BTB
834.64
- 0.3SLX 185.132
- 0.3SLY - 1SLZ - 1.54N
Min Fz 30415 3171 1.15DL
29463
+ 1.2SIDL
-1822.08
+ 0.42CL-48.465
+ 0.42PLB-169.109
+ 0.462TLB-10.111
+ 0.462BTB
-849.305
+ 0.3SLX-254.927
+ 0.3SLY + 1SLZ + 1.5
Max Mx 30392 2103 1.15DL
29439
+ 1.2SIDL
8853.004
+ 1.4CL +49.533
1.4PLB + 1.54TLB
13.332 + 1.54BTB
18.57 333.534 1759.104
Min Mx 30392 2104 1.15DL
29440
+ 1.2SIDL
-2133.438
+ 1.4CL -58.592
+ 1.4PLB + 1.54TLB
-5.82 - 1.54BTB
-22.36 -347.389 -1829.964
Max My 30410 3171 1.15DL
29457
+ 1.2SIDL
9605.008
+ 0.42CL13.156
+ 0.42PLB +51.248
0.462TLB9.247
+ 0.462BTB
1633.515
+ 0.3SLX312.307
+ 0.3SLY + 1SLZ + 1.5
Min My 30374 3178 1.15DL
29421
+ 1.2SIDL
-1939.45
+ 0.42CL-10.271
+ 0.42PLB +-49.042
0.462TLB-11.86
- 0.462BTB
-1667.238
- 0.3SLX-432.593
- 0.3SLY - 1SLZ - 1.54N
Max Mz 30392 2104 1.15DL
29439
+ 1.2SIDL
9302.502
+ 1.4CL +54.711
1.4PLB + 1.54TLB
13.878 - 1.54BTB
17.689 319.063 1887.914
Min Mz 30374 2103 1.15DL
29422
+ 1.2SIDL
-1852.168
+ 1.4CL -58.218
+ 1.4PLB + 1.54TLB
-11.621 + -20.764
1.54BTB -349.86 -1970.733

ODE MDE
Maximum Tension Force (kN) -1862.74 -2607.59
Skin Friction (kN) 1110.67
Final Axial Load (kN) -752.07 -1496.92

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


40 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -741.5 2002 2982 0.671 OK
Minima 9786 854.9 4538 0.188 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 84.79 OK
Minima -220 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.45 OK 30.55 OK
Minima 1.933 OK 14.6 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C40


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C40

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26231 1004 1DL25169
+ 1SIDL 5104.091
+ 1CL + 1PLB + 0.519
1.1TLB - 1.1BTB
-6.476 -0.315 20.395 1.561
Min Fx 26231 1001 1DL25169
+ 1SIDL 4573.149
+ 1CL + 1PLA + 9.57
1.1TLA + -7.053
1.1BTA 0.055 -22.729 -84.046
Max Fy 26260 1005 1DL25168
+ 1SIDL 5081.438
+ 1CL + 1PLA +38.972
1PLB + 1.1TLA
-15.828
+ 1.1TLB
-0.109
+ 1.1BTA +35.54
1.1BTB -34.446
Min Fy 26242 1005 1DL25180
+ 1SIDL 5081.438
+ 1CL + 1PLA -15.279
+ 1PLB + 1.1TLA3.66
+ 1.1TLB
-0.109
+ 1.1BTA-29.634
+ 1.1BTB -94.425
Max Fz 26243 1001 1DL25181
+ 1SIDL 4573.149
+ 1CL + 1PLA +-9.618
1.1TLA + 1.1BTA
4.355 0.055 -26.08 -50.703
Min Fz 26260 1005 1DL25168
+ 1SIDL 5081.438
+ 1CL + 1PLA +38.972
1PLB + 1.1TLA
-15.828
+ 1.1TLB
-0.109
+ 1.1BTA +35.54
1.1BTB -34.446
Max Mx 26231 1001 1DL25169
+ 1SIDL 4573.149
+ 1CL + 1PLA + 9.57
1.1TLA + -7.053
1.1BTA 0.055 -22.729 -84.046
Min Mx 26231 1006 1DL25169
+ 1SIDL 5084.389
+ 1CL + 1PLA +-4.416
1PLB + 1.1TLA
-7.522
+ 1.1TLB
-0.459
- 1.1BTA - 1.1BTB
8.067 42.032
Max My 26260 1004 1DL25168
+ 1SIDL 5104.091
+ 1CL + 1PLB + 0.746
1.1TLB - 1.1BTB
-9.219 -0.315 45.253 3.567
Min My 26236 1001 1DL25175
+ 1SIDL 4573.149
+ 1CL + 1PLA +-2.813
1.1TLA + -0.554
1.1BTA 0.055 -43.037 -98.97
Max Mz 26234 1006 1DL25173
+ 1SIDL 5084.389
+ 1CL + 1PLA +-0.096
1PLB + 1.1TLA
-4.214
+ 1.1TLB
-0.459
- 1.1BTA -15.093
- 1.1BTB 50.481
Min Mz 26234 1005 1DL25173
+ 1SIDL 5081.438
+ 1CL + 1PLA + 1.449
1PLB + 1.1TLA-4.27
+ 1.1TLB
-0.109
+ 1.1BTA-30.419
+ 1.1BTB -157.801

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26231 1004 1DL25169
+ 1SIDL 5104.091
+ 1CL + 1PLB + 0.519
1.1TLB - 1.1BTB
-6.476 -0.315 20.395 1.561
Min Fx 26231 1023 1DL25170
+ 1SIDL 3832.748
+ 0.3SLX + 1SLY
-27.611
+ 0.3SLZ -48.069 -4.92 -339.967 -288.78
Max Fy 26260 1152 1DL25168
+ 1SIDL 3926.408
- 1COL(-X)-MLC
398.382 -12.841 -3.33 25.793 659.18
Min Fy 26260 1086 1DL25168
+ 1SIDL 4218.229
+ 0.3CL + 0.3PLA
-237.257
+ 0.3PLB
-119.475
+ 0.33TLA-12.656
+ 0.33TLB --56.943
0.33BTA - -159.578
0.33BTB - 1SLX - 0.3SLY
Max Fz 26260 3071 1DL25168
+ 1SIDL 4369.263
+ 0.3CL + 0.3PLB92.2
+ 0.33TLB
289.173
+ 0.33BTB
6.958
+ 0.3SLX
262.405
+ 0.3SLY + 1SLZ
60.64
+ 1.1NLB
Min Fz 26260 3047 1DL25199
+ 1SIDL 4053.294
+ 0.3CL + 0.3PLA
-60.286
+ 0.33TLA
-310.829
+ 0.33BTA
-7.473
+ 0.3SLX
-515.417
+ 0.3SLY-159.889
+ 1SLZ + 1.1NLA
Max Mx 26231 2031 1DL25169
+ 1SIDL 4196.379
+ 0.3CL + 0.3PLA
106.521
+ 0.33TLA38.349
+ 0.33BTA
12.125
+ 1SLX +324.6
0.3SLY + 680.878
0.3SLZ + 1.1LLA
Min Mx 26231 1086 1DL25169
+ 1SIDL 4218.229
+ 0.3CL + 0.3PLA
-97.573
+ 0.3PLB-51.179
+ 0.33TLA-12.656
+ 0.33TLB-329.717
- 0.33BTA - -733.012
0.33BTB - 1SLX - 0.3SLY
Max My 26235 3071 1DL25173
+ 1SIDL 4369.263
+ 0.3CL + 0.3PLB
3.175
+ 0.33TLB 6.555
+ 0.33BTB
6.958
+ 0.3SLX
1162.531
+ 0.3SLY +228.678
1SLZ + 1.1NLB
Min My 26234 3047 1DL25173
+ 1SIDL 4053.294
+ 0.3CL + 0.3PLA
-4.791
+ 0.33TLA
-18.112
+ 0.33BTA
-7.473
+ 0.3SLX
-1200.038
+ 0.3SLY +-348.18
1SLZ + 1.1NLA
Max Mz 26234 1086 1DL25173
+ 1SIDL 4352.239
+ 0.3CL + 0.3PLA
15.057
+ 0.3PLB +2.886
0.33TLA 11.963
+ 0.33TLB -405.182
0.33BTA - 0.33BTB
922.145- 1SLX - 0.3SLY
Min Mz 26237 1152 1DL25176
+ 1SIDL 3926.408
- 1COL(-X)-MLC22.373 -1.078 -3.33 -31.819 -1049.99
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26231 2104 1.15DL
25169
+ 1.2SIDL
6148.52
+ 1.4CL189.937
+ 1.4PLB + 1.54TLB
6.794 - 1.54BTB
21.211 128.008 1402.151
Min Fx 26231 2123 1.15DL
25170
+ 1.2SIDL
4404.348
+ 0.3SLX-35.053
+ 1SLY + 0.3SLZ
-59.401 -6.14 -425.601 -358.876
Max Fy 26260 1452 1.15DL
25168
+ 1.2SIDL
4510.267
- 1.5COL(-X)-MLC
593.412 -15.711 -4.888 29.214 988.678
Min Fy 26260 2104 1.15DL
25199
+ 1.2SIDL
6044.736
+ 1.4CL-466.979
+ 1.4PLB + 1.54TLB
-52.547 - 1.54BTB
-21.74 -27.114 -758.158
Max Fz 26260 3171 1.15DL
25168
+ 1.2SIDL
5115.19
+ 0.42CL115.137
+ 0.42PLB 364.224
+ 0.462TLB8.767
+ 0.462BTB
326.758
+ 0.3SLX + 74.79
0.3SLY + 1SLZ + 1.
Min Fz 26260 3147 1.15DL
25199
+ 1.2SIDL
4706.247
+ 0.42CL-76.401
+ 0.42PLA-389.467
+ 0.462TLA-9.334
+ 0.462BTA
-649.619
+ 0.3SLX-201.006
+ 0.3SLY + 1SLZ + 1.5
Max Mx 26231 2104 1.15DL
25169
+ 1.2SIDL
6148.52
+ 1.4CL189.937
+ 1.4PLB + 1.54TLB
6.794 - 1.54BTB
21.211 128.008 1402.151
Min Mx 26231 2103 1.15DL
25170
+ 1.2SIDL
6042.645
+ 1.4CL-177.643
+ 1.4PLB + 1.54TLB
-25.457 + -21.825
1.54BTB -133.266 -1705.649
Max My 26235 3171 1.15DL
25173
+ 1.2SIDL
5115.19
+ 0.42CL + 0.42PLB
3.86 + 8.345
0.462TLB8.767
+ 0.462BTB
1462.756
+ 0.3SLX288.958
+ 0.3SLY + 1SLZ + 1.
Min My 26234 3147 1.15DL
25173
+ 1.2SIDL
4706.247
+ 0.42CL -6.139
+ 0.42PLA +-22.318
0.462TLA-9.334
+ 0.462BTA
-1506.971
+ 0.3SLX-435.856
+ 0.3SLY + 1SLZ + 1.5
Max Mz 26235 2104 1.15DL
25173
+ 1.2SIDL
6148.52
+ 1.4CL + 1.4PLB
9.99 + 1.54TLB
-3.142 - 1.54BTB
21.211 133.749 1815.203
Min Mz 26234 2103 1.15DL
25173
+ 1.2SIDL
6042.645
+ 1.4CL -24.552
+ 1.4PLB + 1.54TLB
-7.569 + -21.825
1.54BTB -171.141 -1940.201

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 5104.091 4573.149 9575.000 OK
ODE Seismic 5104.091 3832.748 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 16
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 6043 1948 2707 0.720 OK
Minima 5115 335.2 2535 0.132 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 70.82 OK
Minima -29.02 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.305 OK 36.54 OK
Minima 3.328 OK 24.68 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.9645 m
Hence de = 0.907 m and dv = 0.816 m
Horizontal resultant shear force at the section, Vu = 594 kN
Corresponding axial compressive force, N = 4510 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 4536 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0023 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.232 %
Horizontal shear force, Vu = 594 kN
Shear stress (vv = Vu /(bv . dv) = 606.00 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.454 Mpa
= 454 kN/m2
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885


Allowable shear stress in concrete, s vc = 401.301 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.20
Modified shear strength of concrete (n s vc ) = 481.32 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 122.13 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 391.83 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C41, C44, C46 & C47


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C41, C44, C46 & C47

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26264 1004 1DL25202
+ 1SIDL 6136.562
+ 1CL + 1PLB +-7.447
1.1TLB - -13.914
1.1BTB -1.393 27.946 -12.794
Min Fx 26561 1001 1DL25499
+ 1SIDL 3641.237
+ 1CL + 1PLA + 5.858
1.1TLA + -0.803
1.1BTA 0.283 -32.014 -90.604
Max Fy 26326 1005 1DL25234
+ 1SIDL 5631.835
+ 1CL + 1PLA +51.606
1PLB + 1.1TLA
-28.087
+ 1.1TLB
-0.458
+ 1.1BTA +81.908
1.1BTB 15.104
Min Fy 26293 1006 1DL25201
+ 1SIDL 6116.799
+ 1CL + 1PLA -24.016
+ 1PLB + 1.1TLA
-24.557
+ 1.1TLB
-2.015
- 1.1BTA -75.883
1.1BTB -31.969
Max Fz 26590 1004 1DL25498
+ 1SIDL 4043.936
+ 1CL + 1PLB +-5.231
1.1TLB - 1.1BTB
8.51 -0.461 -20.531 -19.41
Min Fz 26326 1005 1DL25234
+ 1SIDL 5631.835
+ 1CL + 1PLA +51.606
1PLB + 1.1TLA
-28.087
+ 1.1TLB
-0.458
+ 1.1BTA +81.908
1.1BTB 15.104
Max Mx 26264 1005 1DL25202
+ 1SIDL 6008.191
+ 1CL + 1PLA + 8.286
1PLB + 1.1TLA
-15.158
+ 1.1TLB0.334
+ 1.1BTA +7.331
1.1BTB -137.332
Min Mx 26297 1006 1DL25235
+ 1SIDL 5200.492
+ 1CL + 1PLA + 1.493
1PLB + 1.1TLA
-13.206
+ 1.1TLB
-3.158
- 1.1BTA - -1.184
1.1BTB 50.871
Max My 26293 1004 1DL25201
+ 1SIDL 6136.562
+ 1CL + 1PLB -11.632
+ 1.1TLB - -21.342
1.1BTB -1.393 84.241 -43.317
Min My 26600 1002 1DL25539
+ 1SIDL 4224.246
+ 1CL + 1PLA + 0.296
1.1TLA - 1.1BTA
-2.007 -1.754 -68.554 -3.319
Max Mz 26270 1006 1DL25209
+ 1SIDL 6116.799
+ 1CL + 1PLA +-0.739
1PLB + 1.1TLA
-4.145
+ 1.1TLB
-2.015
- 1.1BTA -49.008
- 1.1BTB 66.763
Min Mz 26301 1005 1DL25240
+ 1SIDL 5631.835
+ 1CL + 1PLA + 2.632
1PLB + 1.1TLA
-7.115
+ 1.1TLB
-0.458
+ 1.1BTA-48.289
+ 1.1BTB -170.318

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26264 2070 1DL25203
+ 1SIDL + 0.3CL
6847.7
+ 0.3PLB
66.006
+ 0.33TLB33.918
- 0.33BTB
2.735
- 0.3SLX
349.676
- 1SLY - 0.3SLZ
299.957
- 1.1LLB
Min Fx 26297 1007 1DL25236
+ 1SIDL 2363.531
+ 1SLX + 0.3SLY
-100.337
+ 0.3SLZ -72.363 -10.755 -372.463 -826.157
Max Fy 26326 1152 1DL25234
+ 1SIDL 5570.942
- 1COL(-X)-MLC
418.615 -46.163 3.011 134.246 747.652
Min Fy 26293 1086 1DL25201
+ 1SIDL 4265.895
+ 0.3CL + 0.3PLA
-265.47
+ 0.3PLB
-127.154
+ 0.33TLA +-9.012
0.33TLB --45.033
0.33BTA - -265.219
0.33BTB - 1SLX - 0.3SLY
Max Fz 26590 3071 1DL25498
+ 1SIDL 3812.169
+ 0.3CL + 0.3PLB
80.012
+ 0.33TLB323.85
+ 0.33BTB
6.349
+ 0.3SLX
114.986
+ 0.3SLY + 30.501
1SLZ + 1.1NLB
Min Fz 26623 3047 1DL25562
+ 1SIDL 3109.805
+ 0.3CL + 0.3PLA
-57.187
+ 0.33TLA
-332.221
+ 0.33BTA
-7.061
+ 0.3SLX
-457.103
+ 0.3SLY-161.493
+ 1SLZ + 1.1NLA
Max Mx 26561 2031 1DL25499
+ 1SIDL 3457.156
+ 0.3CL + 0.3PLA
92.197
+ 0.33TLA49.438
+ 0.33BTA
10.257
+ 1SLX286.608
+ 0.3SLY + 682.267
0.3SLZ + 1.1LLA
Min Mx 26297 3062 1DL25235
+ 1SIDL 2694.827
+ 0.3CL + 0.3PLB
-101.083
+ 0.33TLB
-73.469
- 0.33BTB
-11.342
- 1SLX-313.541
- 0.3SLY - 0.3SLZ
-698.385
- 1.1NLB
Max My 26566 3071 1DL25504
+ 1SIDL 3812.169
+ 0.3CL + 0.3PLB
4.117
+ 0.33TLB20.458
+ 0.33BTB
6.349
+ 0.3SLX
1189.547
+ 0.3SLY +233.675
1SLZ + 1.1NLB
Min My 26598 3047 1DL25537
+ 1SIDL 3109.805
+ 0.3CL + 0.3PLA
-3.691
+ 0.33TLA-9.019
+ 0.33BTA
-7.061
+ 0.3SLX
-1228.139
+ 0.3SLY-337.067
+ 1SLZ + 1.1NLA
Max Mz 26268 1086 1DL25207
+ 1SIDL 6073.261
+ 0.3CL + 0.3PLA
7.873
+ 0.3PLB + 0.33TLA
0.2 +7.059
0.33TLB -374.274
0.33BTA - 0.33BTB
932.672- 1SLX - 0.3SLY
Min Mz 26303 1152 1DL25242
+ 1SIDL 5570.942
- 1COL(-X)-MLC27.824 -7.132 3.011 -95.872 -1078.802
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26297 2103 1.15DL
25235
+ 1.2SIDL
10152.927
+ 1.4CL233.671
+ 1.4PLB + 1.54TLB
28.938 + 14.956
1.54BTB 100.841 1228.708
Min Fx 26297 2107 1.15DL
25236
+ 1.2SIDL
2522.197
+ 1SLX -127.069
+ 0.3SLY + 0.3SLZ
-89.576 -13.371 -466.791 -1034.887
Max Fy 26326 1452 1.15DL
25234
+ 1.2SIDL
6880.493
- 1.5COL(-X)-MLC
621.411 -62.253 4.964 181.852 1112.743
Min Fy 26326 2104 1.15DL
25265
+ 1.2SIDL
2856.84
+ 1.4CL-481.517
+ 1.4PLB + -113.178
1.54TLB - -18.877
1.54BTB -59.567 -605.04
Max Fz 26590 3171 1.15DL
25498
+ 1.2SIDL
4495.787
+ 0.42CL100.667
+ 0.42PLB 407.045
+ 0.462TLB8.004
+ 0.462BTB
145.398
+ 0.3SLX +40.229
0.3SLY + 1SLZ + 1.
Min Fz 26623 3147 1.15DL
25562
+ 1.2SIDL
3546.504
+ 0.42CL-72.006
+ 0.42PLA-415.785
+ 0.462TLA-8.793
+ 0.462BTA
-577.708
+ 0.3SLX-201.799
+ 0.3SLY + 1SLZ + 1.5
Max Mx 26561 2103 1.15DL
25499
+ 1.2SIDL
4834.721
+ 1.4CL180.861
+ 1.4PLB + 1.54TLB
18.639 + 1.54BTB
17.53 75.561 1298.777
Min Mx 26297 2104 1.15DL
25236
+ 1.2SIDL
2856.84
+ 1.4CL-203.465
+ 1.4PLB + 1.54TLB
-63.723 - -18.877
1.54BTB -118.805 -1516.721
Max My 26566 3171 1.15DL
25504
+ 1.2SIDL
4495.787
+ 0.42CL + 0.42PLB
5.32 +25.577
0.462TLB8.004
+ 0.462BTB
1495.811
+ 0.3SLX294.415
+ 0.3SLY + 1SLZ + 1.
Min My 26597 3147 1.15DL
25536
+ 1.2SIDL
3546.504
+ 0.42CL -3.555
+ 0.42PLA +-31.157
0.462TLA-8.793
+ 0.462BTA
-1540.978
+ 0.3SLX-426.719
+ 0.3SLY + 1SLZ + 1.5
Max Mz 26268 2104 1.15DL
25206
+ 1.2SIDL
8004.497
+ 1.4CL + 1.4PLB
3.842 + 1.54TLB
-6.499 - 1.54BTB
11.618 98.66 1809.147
Min Mz 26301 2103 1.15DL
25240
+ 1.2SIDL
3161.327
+ 1.4CL + 1.4PLB
0.907 + 1.54TLB
-25.104 + -17.317
1.54BTB -251.384 -1953.649

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 6136.562 3641.237 9575.000 OK
ODE Seismic 6847.7 2363.531 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 19 18
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 3161 1970 2133 0.924 OK
Minima 4496 150.9 2474 0.061 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 73.62 OK
Minima -63.97 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.954 OK 41.38 OK
Minima 2.584 OK 19.27 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.9645 m
Hence de = 0.907 m and dv = 0.816 m
Horizontal resultant shear force at the section, Vu = 625 kN
Corresponding axial compressive force, N = 6880 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 5104 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0026 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.260 %
Horizontal shear force, Vu = 625 kN
Shear stress (vv = Vu /(bv . dv) = 637.55 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.472 Mpa
= 472 kN/m2
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885


Allowable shear stress in concrete, s vc = 417.369 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.30
Modified shear strength of concrete (n s vc ) = 544.33 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 91.32 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 391.83 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C42, C43, C45 & C48


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C42, C43, C45 & C48

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26363 1003 1DL25301
+ 1SIDL 6672.765
+ 1CL + 1PLB + 11.55
1.1TLB + -14.18
1.1BTB -4.964 23.646 -79.266
Min Fx 26396 1001 1DL25334
+ 1SIDL +4645.65
1CL + 1PLA + 8.194
1.1TLA + -8.473
1.1BTA -0.3 -20.126 -85.518
Max Fy 26557 1005 1DL25465
+ 1SIDL 5766.438
+ 1CL + 1PLA +43.119
1PLB + 1.1TLA
-21.019
+ 1.1TLB 1.32
+ 1.1BTA +55.105
1.1BTB -20.665
Min Fy 26539 1005 1DL25477
+ 1SIDL 5766.438
+ 1CL + 1PLA -16.008
+ 1PLB + 1.1TLA
4.455
+ 1.1TLB 1.32
+ 1.1BTA-37.963
+ 1.1BTB -101.402
Max Fz 26375 1001 1DL25313
+ 1SIDL 5789.656
+ 1CL + 1PLA +-9.646
1.1TLA + 1.1BTA
6.041 -3.386 -40.564 -51.29
Min Fz 26392 1005 1DL25300
+ 1SIDL 6671.388
+ 1CL + 1PLA +39.294
1PLB + 1.1TLA
-25.956
+ 1.1TLB
-3.932
+ 1.1BTA +74.484
1.1BTB -30.22
Max Mx 26528 1005 1DL25466
+ 1SIDL 5766.438
+ 1CL + 1PLA +18.073
1PLB + 1.1TLA
-12.238
+ 1.1TLB 1.32
+ 1.1BTA +1.365
1.1BTB -122.733
Min Mx 26363 1006 1DL25301
+ 1SIDL 6342.342
+ 1CL + 1PLA +-1.185
1PLB + 1.1TLA
-11.594
+ 1.1TLB
-7.219
- 1.1BTA - 1.1BTB
2.919 47.65
Max My 26392 1003 1DL25300
+ 1SIDL 6672.765
+ 1CL + 1PLB +27.637
1.1TLB + -22.219
1.1BTB -4.964 81.898 -13.884
Min My 26369 1001 1DL25308
+ 1SIDL 5789.656
+ 1CL + 1PLA +-3.671
1.1TLA + -2.265
1.1BTA -3.386 -59.467 -95.328
Max Mz 26400 1006 1DL25339
+ 1SIDL 5196.907
+ 1CL + 1PLA +-0.308
1PLB + 1.1TLA
-3.925
+ 1.1TLB
-2.204
- 1.1BTA -53.019
- 1.1BTB 53.302
Min Mz 26531 1005 1DL25470
+ 1SIDL 5766.438
+ 1CL + 1PLA + 1PLB
2.9+ 1.1TLA
-6.259
+ 1.1TLB 1.32
+ 1.1BTA-35.022
+ 1.1BTB -162.732

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26363 3063 1DL25301
+ 1SIDL 7924.725
+ 0.3CL + 0.3PLB
68.011
+ 0.33TLB50.546
+ 0.33BTB
-0.179
+ 0.3SLX
362.547
+ 1SLY + 0.3SLZ
285.844
+ 1.1NLB
Min Fx 26363 1023 1DL25302
+ 1SIDL 2697.468
+ 0.3SLX + 1SLY
-54.424
+ 0.3SLZ -73.18 -8.049 -370.345 -352.232
Max Fy 26557 1152 1DL25465
+ 1SIDL 4542.788
- 1COL(-X)-MLC
396.058 -22.389 -0.763 38.164 651.416
Min Fy 26425 1086 1DL25333
+ 1SIDL 4269.165
+ 0.3CL + 0.3PLA
-234.539
+ 0.3PLB
-129.087
+ 0.33TLA-10.218
+ 0.33TLB --65.186
0.33BTA - -179.521
0.33BTB - 1SLX - 0.3SLY
Max Fz 26524 3071 1DL25432
+ 1SIDL 6091.885
+ 0.3CL + 0.3PLB
83.887
+ 0.33TLB
294.431
+ 0.33BTB
5.965
+ 0.3SLX
228.212
+ 0.3SLY + 1SLZ
51.35
+ 1.1NLB
Min Fz 26392 3047 1DL25331
+ 1SIDL 3391.651
+ 0.3CL + 0.3PLA
-66.692
+ 0.33TLA
-331.287
+ 0.33BTA
-10.636
+ 0.3SLX
-537.165
+ 0.3SLY-215.402
+ 1SLZ + 1.1NLA
Max Mx 26528 1079 1DL25466
+ 1SIDL 5077.877
+ 0.3CL + 0.3PLA
106.413
+ 0.3PLB31.007
+ 0.33TLA +8.787
0.33TLB +329.427
0.33BTA + 663.779
0.33BTB + 1SLX + 0.3S
Min Mx 26363 1086 1DL25301
+ 1SIDL 3166.887
+ 0.3CL + 0.3PLA
-92.326
+ 0.3PLB-76.644
+ 0.33TLA-15.344
+ 0.33TLB-320.932
- 0.33BTA - -767.033
0.33BTB - 1SLX - 0.3SLY
Max My 26499 3071 1DL25437
+ 1SIDL 6091.885
+ 0.3CL + 0.3PLB
2.409
+ 0.33TLB 0.886
+ 0.33BTB
5.965
+ 0.3SLX
1163.621
+ 0.3SLY +226.803
1SLZ + 1.1NLB
Min My 26367 3047 1DL25306
+ 1SIDL 3391.651
+ 0.3CL + 0.3PLA
-9.457
+ 0.33TLA
-20.299
+ 0.33BTA
-10.636
+ 0.3SLX
-1218.559
+ 0.3SLY-346.659
+ 1SLZ + 1.1NLA
Max Mz 26531 1086 1DL25470
+ 1SIDL +5063.06
0.3CL + 0.3PLA
13.885
+ 0.3PLB +1.691
0.33TLA +8.267
0.33TLB -377.371
0.33BTA - 0.33BTB
914.918- 1SLX - 0.3SLY
Min Mz 26534 1152 1DL25473
+ 1SIDL 4542.788
- 1COL(-X)-MLC21.935 -1.345 -0.763 -58.512 -1045.615
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26363 2103 1.15DL
25301
+ 1.2SIDL
10764.707
+ 1.4CL179.721
+ 1.4PLB + 1.54TLB
27.995 + 12.337
1.54BTB 91.02 1303.722
Min Fx 26363 2123 1.15DL
25302
+ 1.2SIDL
2974.904
+ 0.3SLX-66.438
+ 1SLY + 0.3SLZ
-89.182 -9.675 -461.312 -433.709
Max Fy 26557 1452 1.15DL
25465
+ 1.2SIDL
5270.146
- 1.5COL(-X)-MLC
590.136 -27.799 -1.208 39.805 978.29
Min Fy 26425 2104 1.15DL
25364
+ 1.2SIDL
6018.547
+ 1.4CL-455.687
+ 1.4PLB + 1.54TLB
-71.376 - -16.937
1.54BTB -53.321 -766.26
Max Fz 26524 3171 1.15DL
25432
+ 1.2SIDL
7203.845
+ 0.42CL104.921
+ 0.42PLB 371.567
+ 0.462TLB7.522
+ 0.462BTB
281.865
+ 0.3SLX +64.264
0.3SLY + 1SLZ + 1.
Min Fz 26392 3147 1.15DL
25331
+ 1.2SIDL
3792.853
+ 0.42CL -83.51
+ 0.42PLA-413.813
+ 0.462TLA-12.927
+ 0.462BTA
-676.864
+ 0.3SLX-267.014
+ 0.3SLY + 1SLZ + 1.5
Max Mx 26528 2103 1.15DL
25466
+ 1.2SIDL
7205.704
+ 1.4CL204.299
+ 1.4PLB + 1.54TLB
-4.236 + 14.593
1.54BTB 116.204 1286.72
Min Mx 26363 2104 1.15DL
25302
+ 1.2SIDL
4690.857
+ 1.4CL-162.829
+ 1.4PLB + 1.54TLB
-64.778 - -25.066
1.54BTB -106.314 -1561.676
Max My 26499 3171 1.15DL
25437
+ 1.2SIDL
7203.845
+ 0.42CL +2.989
0.42PLB + 1.411
0.462TLB7.522
+ 0.462BTB
1464.923
+ 0.3SLX286.586
+ 0.3SLY + 1SLZ + 1.
Min My 26367 3147 1.15DL
25306
+ 1.2SIDL
3792.853
+ 0.42CL-11.553
+ 0.42PLA +-24.687
0.462TLA
-12.927
+ 0.462BTA
-1528.269
+ 0.3SLX-433.153
+ 0.3SLY + 1SLZ + 1.5
Max Mz 26532 2104 1.15DL
25470
+ 1.2SIDL
7170.708
+ 1.4CL +13.126
1.4PLB + 1.54TLB
-1.743 - 1.54BTB
13.69 85.722 1795.081
Min Mz 26531 2103 1.15DL
25470
+ 1.2SIDL
6404.539
+ 1.4CL -20.763
+ 1.4PLB + 1.54TLB
-13.215 + -12.953
1.54BTB -140.099 -1935.259

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 6672.765 4645.65 9575.000 OK
ODE Seismic 7924.725 2697.468 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 16 22
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 3793 1588 2215 0.717 OK
Minima 7204 289.1 2852 0.101 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 76.24 OK
Minima -51.5 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 6.238 OK 43.86 OK
Minima 3.508 OK 25.79 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.966 m
Hence de = 0.907 m and dv = 0.817 m
Horizontal resultant shear force at the section, Vu = 591 kN
Corresponding axial compressive force, N = 5270 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 4423 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0022 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.226 %
Horizontal shear force, Vu = 591 kN
Shear stress (vv = Vu /(bv . dv) = 602.79 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.450 Mpa
= 450 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 397.815 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.23
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Modified shear strength of concrete (n s vc ) = 490.50 kN/m2


Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 110.06 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 392.03 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMNS C52, C54 TO C56 & C58 TO


C60
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP C52, C54 TO C56 & C58 TO C60

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13500 1005 1DL11562
+ 1SIDL 2292.735
+ 1CL + 1PLA +13.717
1PLB + 1.1TLA
27.134
+ 1.1TLB
-0.048
+ 1.1BTA-59.199
+ 1.1BTB -68.593
Min Fx 13302 1001 1DL11364
+ 1SIDL 1482.021
+ 1CL + 1PLA + 7.669
1.1TLA + 17.912
1.1BTA 0.292 -52.973 -48.29
Max Fy 13529 1005 1DL11561
+ 1SIDL 2292.735
+ 1CL + 1PLA +37.215
1PLB + 1.1TLA
44.293
+ 1.1TLB
-0.048
+ 1.1BTA-174.264
+ 1.1BTB 17.164
Min Fy 13529 1006 1DL11561
+ 1SIDL 1933.417
+ 1CL + 1PLA +-11.38
1PLB + 1.1TLA
35.355
+ 1.1TLB
-0.904
- 1.1BTA-145.686
- 1.1BTB -8.973
Max Fz 13463 1004 1DL11495
+ 1SIDL 2243.635
+ 1CL + 1PLB +-1.232
1.1TLB - 1.1BTB
50.934 -0.476 -179.914 -7.385
Min Fz 13446 1004 1DL11508
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.111
1.1TLB - 1.1BTB
-8.149 -0.476 43.193 0.974
Max Mx 13302 1001 1DL11364
+ 1SIDL 1482.021
+ 1CL + 1PLA + 7.669
1.1TLA + 17.912
1.1BTA 0.292 -52.973 -48.29
Min Mx 13566 1006 1DL11628
+ 1SIDL 1689.226
+ 1CL + 1PLA +-0.014
1PLB + 1.1TLA
23.262
+ 1.1TLB
-1.502
- 1.1BTA -62.696
- 1.1BTB 25.839
Max My 13441 1004 1DL11504
+ 1SIDL 2243.635
+ 1CL + 1PLB +-0.266
1.1TLB - 1.1BTB
1.051 -0.476 66.954 0.918
Min My 13463 1004 1DL11495
+ 1SIDL 2243.635
+ 1CL + 1PLB +-1.232
1.1TLB - 1.1BTB
50.934 -0.476 -179.914 -7.385
Max Mz 13371 1006 1DL11434
+ 1SIDL 2075.256
+ 1CL + 1PLA +-0.142
1PLB + 1.1TLA
13.855
+ 1.1TLB-0.46
- 1.1BTA -28.965
1.1BTB 28.943
Min Mz 13503 1005 1DL11566
+ 1SIDL 2292.735
+ 1CL + 1PLA + 0.504
1PLB + 1.1TLA
14.696
+ 1.1TLB
-0.048
+ 1.1BTA +23.275
1.1BTB -95.042

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13500 1079 1DL11562
+ 1SIDL 3641.602
+ 0.3CL + 0.3PLA
99.157
+ 0.3PLB64.988
+ 0.33TLA +4.542
0.33TLB +190.486
0.33BTA + 336.613
0.33BTB + 1SLX + 0.3S
Min Fx 13500 1007 1DL11563
+ 1SIDL + 1SLX
27.337
+ 0.3SLY
-89.129
+ 0.3SLZ -25.326 -5.09 -269.02 -484.175
Max Fy 13529 1152 1DL11561
+ 1SIDL 3145.917
- 1COL(-X)-MLC
393.401 55.53 -0.953 -224.732 894.429
Min Fy 13529 1086 1DL11561
+ 1SIDL + 0.3CL
81.282
+ 0.3PLA
-233.689
+ 0.3PLB-69.508
+ 0.33TLA +-5.267
0.33TLB-292.459
- 0.33BTA - -184.644
0.33BTB - 1SLX - 0.3SLY
Max Fz 13463 3071 1DL11495
+ 1SIDL 2492.003
+ 0.3CL + 0.3PLB
75.682
+ 0.33TLB
301.478
+ 0.33BTB
3.287
+ 0.3SLX
-49.974
+ 0.3SLY + 13.333
1SLZ + 1.1NLB
Min Fz 13463 3047 1DL11526
+ 1SIDL 1372.074
+ 0.3CL + 0.3PLA
-55.076
+ 0.33TLA
-227.008
+ 0.33BTA-3.59
+ 0.3SLX
-396.847
+ 0.3SLY +-72.246
1SLZ + 1.1NLA
Max Mx 13302 2031 1DL11364
+ 1SIDL 1743.606
+ 0.3CL + 0.3PLA
77.915
+ 0.33TLA52.025
+ 0.33BTA5.942
+ 1SLX171.081
+ 0.3SLY + 406.376
0.3SLZ + 1.1LLA
Min Mx 13302 3062 1DL11364
+ 1SIDL 1078.306
+ 0.3CL + 0.3PLB
-70.466
+ 0.33TLB
-16.397
- 0.33BTB
-6.032
- 1SLX --251.11
0.3SLY - 0.3SLZ
-445.347
- 1.1NLB
Max My 13438 3071 1DL11500
+ 1SIDL 2492.003
+ 0.3CL + 0.3PLB
3.598
+ 0.33TLB37.802
+ 0.33BTB
3.287
+ 0.3SLX
718.961
+ 0.3SLY +139.738
1SLZ + 1.1NLB
Min My 13568 3047 1DL11631
+ 1SIDL +941.324
0.3CL + 0.3PLA
-3.062
+ 0.33TLA-7.974
+ 0.33BTA
-4.107
+ 0.3SLX
-704.414
+ 0.3SLY-207.243
+ 1SLZ + 1.1NLA
Max Mz 13529 1152 1DL11561
+ 1SIDL 3145.917
- 1COL(-X)-MLC
393.401 55.53 -0.953 -224.732 894.429
Min Mz 13506 1152 1DL11569
+ 1SIDL 3145.917
- 1COL(-X)-MLC7.635 9.892 -0.953 62.977 -662.702
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13500 2103 1.15DL
11562
+ 1.2SIDL
5739.755
+ 1.4CL189.589
+ 1.4PLB + 1.54TLB
66.405 + 1.54BTB
7.683 68.025 649.989
Min Fx 13500 2104 1.15DL
11563
+ 1.2SIDL
-687.044
+ 1.4CL-178.685
+ 1.4PLB + 1.54TLB
-5.145 - 1.54BTB
-8.613 -138.276 -887.411
Max Fy 13529 1452 1.15DL
11561
+ 1.2SIDL
4105.054
- 1.5COL(-X)-MLC
586.735 72.785 -1.32 -295.01 1340.417
Min Fy 13529 2104 1.15DL
11592
+ 1.2SIDL
-687.044
+ 1.4CL-457.307
+ 1.4PLB + 1.54TLB
-3.625 - 1.54BTB
-8.613 -341.522 -109.861
Max Fz 13463 1453 1.15DL
11495
+ 1.2SIDL
2161.458
+ 1.5COL(Z)-MLC
6.418 376.953 -0.013 -739.155 -10.088
Min Fz 13463 3147 1.15DL
11526
+ 1.2SIDL
1541.635
+ 0.42CL-69.208
+ 0.42PLA-287.685
+ 0.462TLA-4.492
+ 0.462BTA
-484.926
+ 0.3SLX-89.523
+ 0.3SLY + 1SLZ + 1.5
Max Mx 13302 2103 1.15DL
11364
+ 1.2SIDL
2260.244
+ 1.4CL149.248
+ 1.4PLB + 1.54TLB
40.829 + 10.116
1.54BTB 18.247 767.396
Min Mx 13302 2104 1.15DL
11365
+ 1.2SIDL
1552.527
+ 1.4CL-138.064
+ 1.4PLB + 1.54TLB
14.96 - -10.257
1.54BTB -103.289 -963.852
Max My 13438 3171 1.15DL
11500
+ 1.2SIDL
2951.258
+ 0.42CL + 0.42PLB
4.58 +46.243
0.462TLB4.174
+ 0.462BTB
901.814
+ 0.3SLX176.437
+ 0.3SLY + 1SLZ + 1.
Min My 13568 3147 1.15DL
11631
+ 1.2SIDL
1039.85
+ 0.42CL -3.937
+ 0.42PLA +-10.871
0.462TLA-5.107
+ 0.462BTA
-885.667
+ 0.3SLX-259.377
+ 0.3SLY + 1SLZ + 1.5
Max Mz 13529 1452 1.15DL
11561
+ 1.2SIDL
4105.054
- 1.5COL(-X)-MLC
586.735 72.785 -1.32 -295.01 1340.417
Min Mz 13503 2103 1.15DL
11566
+ 1.2SIDL
-434.531
+ 1.4CL -18.725
+ 1.4PLB + 1.54TLB
-4.532 + 1.54BTB
-8.2 -30.978 -1164.464

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 2292.735 1482.021 7790.000 OK
ODE Seismic 3641.602 27.337 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 29 16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -434.5 1165 1316 0.885 OK
Minima 1542 493.1 1808 0.273 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 79.58 OK
Minima -151.8 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 4.334 OK 27.95 OK
Minima 0.9085 OK 8.887 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.103 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 16.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13513 1005 1DL11575
+ 1SIDL 2292.735
+ 1CL + 1PLA +-8.247
1PLB + 1.1TLA
-6.518
+ 1.1TLB
-0.048
+ 1.1BTA +30.563
1.1BTB -25.042
Min Fx 13315 1001 1DL11377
+ 1SIDL 1482.021
+ 1CL + 1PLA +-5.111
1.1TLA + -3.604
1.1BTA 0.292 18.822 -14.969
Max Fy 13381 1006 1DL11443
+ 1SIDL 2075.256
+ 1CL + 1PLA + 2.508
1PLB + 1.1TLA
-6.743
+ 1.1TLB-0.46
- 1.1BTA -30.602
1.1BTB 7.606
Min Fy 13513 1005 1DL11575
+ 1SIDL 2292.735
+ 1CL + 1PLA +-8.247
1PLB + 1.1TLA
-6.518
+ 1.1TLB
-0.048
+ 1.1BTA +30.563
1.1BTB -25.042
Max Fz 28516 1004 1DL27500
+ 1SIDL 2243.635
+ 1CL + 1PLB +-0.008
1.1TLB - 1.1BTB
0.777 -0.476 -1.89 -0.025
Min Fz 13447 1004 1DL11509
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.127
1.1TLB - 1.1BTB
-7.934 -0.476 35.044 0.862
Max Mx 13315 1001 1DL11377
+ 1SIDL 1482.021
+ 1CL + 1PLA +-5.111
1.1TLA + -3.604
1.1BTA 0.292 18.822 -14.969
Min Mx 13579 1006 1DL11641
+ 1SIDL 1689.226
+ 1CL + 1PLA + 1.304
1PLB + 1.1TLA
-4.987
+ 1.1TLB
-1.502
- 1.1BTA -25.039
1.1BTB 2.534
Max My 13447 1004 1DL11509
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.127
1.1TLB - 1.1BTB
-7.934 -0.476 35.044 0.862
Min My 28513 1004 1DL27498
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.027
1.1TLB - 1.1BTB
-0.275 -0.476 -2.901 -0.017
Max Mz 13513 1006 1DL11575
+ 1SIDL 1933.417
+ 1CL + 1PLA + 2.442
1PLB + 1.1TLA
-5.061
+ 1.1TLB
-0.904
- 1.1BTA -24.428
1.1BTB 7.676
Min Mz 13513 1005 1DL11575
+ 1SIDL 2292.735
+ 1CL + 1PLA +-8.247
1PLB + 1.1TLA
-6.518
+ 1.1TLB
-0.048
+ 1.1BTA +30.563
1.1BTB -25.042

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13513 1079 1DL11575
+ 1SIDL 3641.602
+ 0.3CL + 0.3PLA
46.944
+ 0.3PLB15.715
+ 0.33TLA +4.542
0.33TLB + 92.164
0.33BTA + 147.811
0.33BTB + 1SLX + 0.3S
Min Fx 13513 1007 1DL11576
+ 1SIDL + 1SLX
27.337
+ 0.3SLY
-53.074
+ 0.3SLZ -25.104 -5.09 -31.659 -113.242
Max Fy 13513 1086 1DL11576
+ 1SIDL 3533.807
+ 0.3CL + 0.3PLA
50.151
+ 0.3PLB16.152
+ 0.33TLA +4.286
0.33TLB - 0.33BTA
65.274 - 0.33BTB
107.477- 1SLX - 0.3SLY
Min Fy 13513 1152 1DL11575
+ 1SIDL 3145.917
- 1COL(-X)-MLC-71.896 -8.037 -0.953 38.347 -268.233
Max Fz 13579 3047 1DL11641
+ 1SIDL 1991.219
+ 0.3CL + 0.3PLA
10.591
+ 0.33TLA 54.048
+ 0.33BTA
2.865
+ 0.3SLX
187.349
+ 0.3SLY +30.594
1SLZ + 1.1NLA
Min Fz 13447 3071 1DL11510
+ 1SIDL 1418.954
+ 0.3CL + 0.3PLB
-17.253
+ 0.33TLB-64.934
+ 0.33BTB
-3.346+ 0.3SLX
-94.821
+ 0.3SLY +-33.565
1SLZ + 1.1NLB
Max Mx 13315 2031 1DL11377
+ 1SIDL 1743.606
+ 0.3CL + 0.3PLA
44.146
+ 0.33TLA 17.294
+ 0.33BTA
5.942
+ 1SLX 82.455
+ 0.3SLY + 0.3SLZ
130.79+ 1.1LLA
Min Mx 13315 3062 1DL11377
+ 1SIDL 1078.306
+ 0.3CL + 0.3PLB
-48.711
+ 0.33TLB-25.736
- 0.33BTB
-6.032
- 1SLX --42.549
0.3SLY - 0.3SLZ
-144.557
- 1.1NLB
Max My 13447 3071 1DL11509
+ 1SIDL 2492.003
+ 0.3CL + 0.3PLB
12.206
+ 0.33TLB 52.381
+ 0.33BTB
3.287+ 0.3SLX
203.296
+ 0.3SLY + 37.299
1SLZ + 1.1NLB
Min My 13447 1022 1DL11509
+ 1SIDL 1297.054
- 0.3SLX - 0.3SLY
-16.365
- 1SLZ -63.804 -3.53 -151.374 -48.262
Max Mz 13513 1007 1DL11575
+ 1SIDL 3479.861
+ 1SLX + 0.3SLY48.773
+ 0.3SLZ 16.358 4.463 89.213 153.384
Min Mz 13513 1152 1DL11575
+ 1SIDL 3145.917
- 1COL(-X)-MLC-71.896 -8.037 -0.953 38.347 -268.233
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13513 1005 1DL11575
+ 1SIDL 2292.735
+ 1CL + 1PLA +-8.247
1PLB + 1.1TLA
-6.518
+ 1.1TLB
-0.048
+ 1.1BTA +30.563
1.1BTB -25.042
Min Fx 13315 1001 1DL11377
+ 1SIDL 1482.021
+ 1CL + 1PLA +-5.111
1.1TLA + -3.604
1.1BTA 0.292 18.822 -14.969
Max Fy 13381 1006 1DL11443
+ 1SIDL 2075.256
+ 1CL + 1PLA + 2.508
1PLB + 1.1TLA
-6.743
+ 1.1TLB-0.46
- 1.1BTA -30.602
1.1BTB 7.606
Min Fy 13513 1005 1DL11575
+ 1SIDL 2292.735
+ 1CL + 1PLA +-8.247
1PLB + 1.1TLA
-6.518
+ 1.1TLB
-0.048
+ 1.1BTA +30.563
1.1BTB -25.042
Max Fz 28516 1004 1DL27500
+ 1SIDL 2243.635
+ 1CL + 1PLB +-0.008
1.1TLB - 1.1BTB
0.777 -0.476 -1.89 -0.025
Min Fz 13447 1004 1DL11509
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.127
1.1TLB - 1.1BTB
-7.934 -0.476 35.044 0.862
Max Mx 13315 1001 1DL11377
+ 1SIDL 1482.021
+ 1CL + 1PLA +-5.111
1.1TLA + -3.604
1.1BTA 0.292 18.822 -14.969
Min Mx 13579 1006 1DL11641
+ 1SIDL 1689.226
+ 1CL + 1PLA + 1.304
1PLB + 1.1TLA
-4.987
+ 1.1TLB
-1.502
- 1.1BTA -25.039
1.1BTB 2.534
Max My 13447 1004 1DL11509
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.127
1.1TLB - 1.1BTB
-7.934 -0.476 35.044 0.862
Min My 28513 1004 1DL27498
+ 1SIDL 2243.635
+ 1CL + 1PLB + 0.027
1.1TLB - 1.1BTB
-0.275 -0.476 -2.901 -0.017
Max Mz 13513 1006 1DL11575
+ 1SIDL 1933.417
+ 1CL + 1PLA + 2.442
1PLB + 1.1TLA
-5.061
+ 1.1TLB
-0.904
- 1.1BTA -24.428
1.1BTB 7.676
Min Mz 13513 1005 1DL11575
+ 1SIDL 2292.735
+ 1CL + 1PLA +-8.247
1PLB + 1.1TLA
-6.518
+ 1.1TLB
-0.048
+ 1.1BTA +30.563
1.1BTB -25.042

ODE MDE
Maximum Tension Force (kN) 27.34 1482.021
Skin Friction (kN) 2684.00
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 39.52 517.7 0.076 OK
Minima 2244 2.138 1195 0.002 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 41.65 OK
Minima -141.2 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 0.000 N/mm2


Steel 0.75fy 0.000 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 3.239 OK 22.46 OK
Minima 1.602 OK 11.86 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.7595 m
Hence de = 0.742 m and dv = 0.668 m
Horizontal resultant shear force at the section, Vu = 591 kN
Corresponding axial compressive force, N = 4105 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 10568 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0053 m2
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Percentage of tensile reinforcement = 100 As /(bv . dv) = 0.792 %


Horizontal shear force, Vu = 591 kN
Shear stress (vv = Vu /(bv . dv) = 885.63 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
1/3 1/3
vc = 0.27/ m (100As/(bd)) (fcu) (where m = 1.25) = 0.683 Mpa
= 683 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 635.693 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.26
Modified shear strength of concrete (n s vc ) = 801.82 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 55.95 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 267.03 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C53


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP C53

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 11366 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13335 1005 1DL11397
+ 1SIDL 1120.585
+ 1CL + 1PLA + 7.111
1PLB + 1.1TLA
3.253
+ 1.1TLB 0.13
+ 1.1BTA-14.121
+ 1.1BTB -83.534
Min Fx 13335 1006 1DL11397
+ 1SIDL +965.822
1CL + 1PLA +-3.739
1PLB + 1.1TLA3.03
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
-4.98 23.316
Max Fy 13364 1005 1DL11396
+ 1SIDL 1120.585
+ 1CL + 1PLA +26.512
1PLB + 1.1TLA
4.253
+ 1.1TLB 0.13
+ 1.1BTA-25.949
+ 1.1BTB -25.64
Min Fy 13364 1006 1DL11396
+ 1SIDL +965.822
1CL + 1PLA +-10.84
1PLB + 1.1TLA
5.191
+ 1.1TLB
-0.154
- 1.1BTA -18.285
- 1.1BTB -1.355
Max Fz 13364 1004 1DL11396
+ 1SIDL 1035.089
+ 1CL + 1PLB +-1.788
1.1TLB - 1.1BTB
7.955 -0.084 -16.148 -7.247
Min Fz 13346 1004 1DL11408
+ 1SIDL 1035.089
+ 1CL + 1PLB + 0.246
1.1TLB - 1.1BTB
-1.681 -0.084 8.706 1.74
Max Mx 13335 1001 1DL11397
+ 1SIDL +1043.23
1CL + 1PLA + 4.318
1.1TLA + 1.1BTA
2.142 0.219 -22.126 -55.626
Min Mx 13335 1006 1DL11397
+ 1SIDL +965.822
1CL + 1PLA +-3.739
1PLB + 1.1TLA3.03
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
-4.98 23.316
Max My 13340 1004 1DL11403
+ 1SIDL 1035.089
+ 1CL + 1PLB +-0.396
1.1TLB - 1.1BTB
0.288 -0.084 14.023 1.705
Min My 13364 1001 1DL11396
+ 1SIDL +1043.23
1CL + 1PLA +16.836
1.1TLA + 1.1BTA
0.871 0.219 -26.323 -19.1
Max Mz 13337 1006 1DL11400
+ 1SIDL +965.822
1CL + 1PLA +-0.824
1PLB + 1.1TLA1.95
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
2.45 29.999
Min Mz 13336 1005 1DL11399
+ 1SIDL 1120.585
+ 1CL + 1PLA + 2.829
1PLB + 1.1TLA
2.901
+ 1.1TLB 0.13
+ 1.1BTA +-7.967
1.1BTB -93.474

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13335 3071 1DL11397
+ 1SIDL 3216.472
+ 0.3CL + 0.3PLB
21.287
+ 0.33TLB 56.441
+ 0.33BTB
3.625
+ 0.3SLX
654.324
+ 0.3SLY +117.642
1SLZ + 1.1NLB
Min Fx 13335 1015 1DL11398
+ 1SIDL-1269.365
+ 0.3SLX + 0.3SLY
-17.932
+ 1SLZ -51.089 -3.647 -708.159 -191.185
Max Fy 13364 1152 1DL11396
+ 1SIDL 1573.157
- 1COL(-X)-MLC345.894 6.722 -2.328 -40.697 659.837
Min Fy 13364 1086 1DL11396
+ 1SIDL +-434.722
0.3CL + 0.3PLA
-185.671
+ 0.3PLB -68.32
+ 0.33TLA +-5.999
0.33TLB-128.878
- 0.33BTA - 0.33BTB
-66.916- 1SLX - 0.3SLY
Max Fz 13364 1153 1DL11396
+ 1SIDL 1797.816
+ 1COL(Z)-MLC4.268 205.248 0.328 -251.52 -11.225
Min Fz 13364 3047 1DL11427
+ 1SIDL-1249.369
+ 0.3CL + 0.3PLA
-50.444
+ 0.33TLA
-197.627
+ 0.33BTA
-3.615
+ 0.3SLX
-457.138
+ 0.3SLY-101.246
+ 1SLZ + 1.1NLA
Max Mx 13335 2031 1DL11397
+ 1SIDL 2352.561
+ 0.3CL + 0.3PLA
61.128
+ 0.33TLA 23.615
+ 0.33BTA5.987
+ 1SLX 219.46
+ 0.3SLY + 440.522
0.3SLZ + 1.1LLA
Min Mx 13335 3062 1DL11397
+ 1SIDL +-424.177
0.3CL + 0.3PLB
-58.476
+ 0.33TLB-18.927
- 0.33BTB
-6.019
- 1SLX-239.964
- 0.3SLY - 0.3SLZ
-488.95
- 1.1NLB
Max My 13337 3071 1DL11399
+ 1SIDL 3216.472
+ 0.3CL + 0.3PLB2.401
+ 0.33TLB 14.492
+ 0.33BTB
3.625
+ 0.3SLX
723.227
+ 0.3SLY +142.239
1SLZ + 1.1NLB
Min My 13336 3047 1DL11399
+ 1SIDL-1249.369
+ 0.3CL + 0.3PLA
-9.442
+ 0.33TLA-20.414
+ 0.33BTA
-3.615
+ 0.3SLX
-730.507
+ 0.3SLY-212.271
+ 1SLZ + 1.1NLA
Max Mz 13364 1152 1DL11396
+ 1SIDL 1573.157
- 1COL(-X)-MLC345.894 6.722 -2.328 -40.697 659.837
Min Mz 13340 1152 1DL11403
+ 1SIDL 1573.157
- 1COL(-X)-MLC 8.64 2.722 -2.328 1.03 -626.577
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13335 3171 1.15DL
11397
+ 1.2SIDL
3947.749
+ 0.42CL26.705
+ 0.42PLB +70.402
0.462TLB4.558
+ 0.462BTB
822.67
+ 0.3SLX148.627
+ 0.3SLY + 1SLZ + 1.
Min Fx 13335 2115 1.15DL
11398
+ 1.2SIDL
-1693.115
+ 0.3SLX-22.611
+ 0.3SLY + 1SLZ
-64.068 -4.575 -888.427 -237.724
Max Fy 13364 1452 1.15DL
11396
+ 1.2SIDL
2029.831
- 1.5COL(-X)-MLC
516.854 8.867 -3.483 -55.325 993.26
Min Fy 13364 2104 1.15DL
11427
+ 1.2SIDL
-332.671
+ 1.4CL-361.727
+ 1.4PLB + 1.54TLB
-15.269 - 1.54BTB
-10.3 -74.227 -469.584
Max Fz 13364 1453 1.15DL
11396
+ 1.2SIDL
2366.82
+ 1.5COL(Z)-MLC
4.416 306.657 0.502 -371.561 -13.333
Min Fz 13364 3147 1.15DL
11427
+ 1.2SIDL
-1665.12
+ 0.42CL-63.449
+ 0.42PLA-248.445
+ 0.462TLA-4.529
+ 0.462BTA
-572.187
+ 0.3SLX-126.124
+ 0.3SLY + 1SLZ + 1.5
Max Mx 13335 2103 1.15DL
11397
+ 1.2SIDL
2821.444
+ 1.4CL118.516
+ 1.4PLB + 1.54TLB
13.358 + 10.273
1.54BTB 60.236 834.706
Min Mx 13335 2104 1.15DL
11398
+ 1.2SIDL
-332.671
+ 1.4CL-114.649
+ 1.4PLB + 1.54TLB
-4.963 - 1.54BTB
-10.3 -71.567 -1016.645
Max My 13337 3171 1.15DL
11399
+ 1.2SIDL
3947.749
+ 0.42CL +3.016
0.42PLB +17.499
0.462TLB4.558
+ 0.462BTB
909.232
+ 0.3SLX179.578
+ 0.3SLY + 1SLZ + 1.
Min My 13336 3147 1.15DL
11399
+ 1.2SIDL
-1665.12
+ 0.42CL-11.783
+ 0.42PLA +-25.383
0.462TLA-4.529
+ 0.462BTA
-918.021
+ 0.3SLX-265.89
+ 0.3SLY + 1SLZ + 1.5
Max Mz 13338 2104 1.15DL
11400
+ 1.2SIDL
2708.694
+ 1.4CL +19.509
1.4PLB + 1.54TLB
7.068 - 1.54BTB
10.237 77.69 1098.571
Min Mz 13337 2103 1.15DL
11400
+ 1.2SIDL
-219.921
+ 1.4CL -14.624
+ 1.4PLB + 1.54TLB
-2.563 + -10.265
1.54BTB -69.792 -1172.633

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 1120.585 965.822 7790.000 OK
ODE Seismic 3216.472 -1269.365 11366.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 32 18
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -1665 955.8 1415 0.676 OK
Minima 2367 371.8 2333 0.159 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 63.18 OK
Minima -276.3 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 9.172 OK 49.68 OK
Minima -0.9728 OK -40.49 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.103 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 16.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13348 1005 1DL11410
+ 1SIDL 1120.585
+ 1CL + 1PLA +-6.687
1PLB + 1.1TLA
-0.428
+ 1.1TLB 0.13
+ 1.1BTA + 1.1BTB
2.98 -17.653
Min Fx 13348 1006 1DL11410
+ 1SIDL +965.822
1CL + 1PLA + 1PLB
2.48+ 1.1TLA
-0.81
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
3.571 7.276
Max Fy 13348 1006 1DL11410
+ 1SIDL +965.822
1CL + 1PLA + 1PLB
2.48+ 1.1TLA
-0.81
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
3.571 7.276
Min Fy 13348 1005 1DL11410
+ 1SIDL 1120.585
+ 1CL + 1PLA +-6.687
1PLB + 1.1TLA
-0.428
+ 1.1TLB 0.13
+ 1.1BTA + 1.1BTB
2.98 -17.653
Max Fz 13348 1001 1DL11410
+ 1SIDL +1043.23
1CL + 1PLA +-4.307
1.1TLA + 1.1BTA
0.363 0.219 0.714 -11.197
Min Fz 13348 1004 1DL11410
+ 1SIDL 1035.089
+ 1CL + 1PLB + 0.259
1.1TLB - 1.1BTB
-1.495 -0.084 5.415 1.235
Max Mx 13348 1001 1DL11410
+ 1SIDL +1043.23
1CL + 1PLA +-4.307
1.1TLA + 1.1BTA
0.363 0.219 0.714 -11.197
Min Mx 13348 1006 1DL11410
+ 1SIDL +965.822
1CL + 1PLA + 1PLB
2.48+ 1.1TLA
-0.81
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
3.571 7.276
Max My 13348 1004 1DL11410
+ 1SIDL 1035.089
+ 1CL + 1PLB + 0.259
1.1TLB - 1.1BTB
-1.495 -0.084 5.415 1.235
Min My 28485 1004 1DL27470
+ 1SIDL 1035.089
+ 1CL + 1PLB + 0.049
1.1TLB - 1.1BTB
-0.108 -0.084 -0.699 -0.07
Max Mz 13348 1006 1DL11410
+ 1SIDL +965.822
1CL + 1PLA + 1PLB
2.48+ 1.1TLA
-0.81
+ 1.1TLB
-0.154
- 1.1BTA - 1.1BTB
3.571 7.276
Min Mz 13348 1005 1DL11410
+ 1SIDL 1120.585
+ 1CL + 1PLA +-6.687
1PLB + 1.1TLA
-0.428
+ 1.1TLB 0.13
+ 1.1BTA + 1.1BTB
2.98 -17.653
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13348 3071 1DL11410
+ 1SIDL 3216.472
+ 0.3CL + 0.3PLB11.69
+ 0.33TLB 49.583
+ 0.33BTB
3.625
+ 0.3SLX
136.601
+ 0.3SLY + 33.827
1SLZ + 1.1NLB
Min Fx 13348 1015 1DL11411
+ 1SIDL-1269.365
+ 0.3SLX + 0.3SLY
-15.589
+ 1SLZ -51.015 -3.647 -80.306 -28.019
Max Fy 13348 1086 1DL11411
+ 1SIDL 2333.661
+ 0.3CL + 0.3PLA
43.953
+ 0.3PLB17.329
+ 0.33TLA +5.869
0.33TLB - 0.33BTA
32.716 - 0.33BTB
80.346- 1SLX - 0.3SLY
Min Fy 13348 1152 1DL11410
+ 1SIDL 1573.157
- 1COL(-X)-MLC-65.928 -0.683 -2.328 4.708 -235.217
Max Fz 13348 3047 1DL11410
+ 1SIDL 3174.284
+ 0.3CL + 0.3PLA
11.689
+ 0.33TLA 50.605
+ 0.33BTA
3.626
+ 0.3SLX
133.959
+ 0.3SLY +33.828
1SLZ + 1.1NLA
Min Fz 13348 3071 1DL11411
+ 1SIDL-1207.181
+ 0.3CL + 0.3PLB
-16.431
+ 0.33TLB -51.54
+ 0.33BTB
-3.616
+ 0.3SLX
-79.336
+ 0.3SLY +-29.433
1SLZ + 1.1NLB
Max Mx 13348 2031 1DL11410
+ 1SIDL 2352.561
+ 0.3CL + 0.3PLA
41.919
+ 0.33TLA 17.794
+ 0.33BTA
5.987
+ 1SLX 49.857
+ 0.3SLY + 118.756
0.3SLZ + 1.1LLA
Min Mx 13348 3062 1DL11410
+ 1SIDL +-424.177
0.3CL + 0.3PLB
-45.281
+ 0.33TLB-18.403
- 0.33BTB
-6.019
- 1SLX --45.577
0.3SLY - 0.3SLZ
-127.021
- 1.1NLB
Max My 13348 1153 1DL11410
+ 1SIDL 1797.816
+ 1COL(Z)-MLC-1.229 -42.123 0.328 138.884 -2.807
Min My 13348 1054 1DL11410
+ 1SIDL-1261.402
+ 0.3CL + 0.3PLA
-15.061
+ 0.33TLA-50.845
- 0.33BTA
-3.651
- 0.3SLX
-130.664
- 0.3SLY - 1SLZ
-42.123
Max Mz 13348 1007 1DL11410
+ 1SIDL 2326.653
+ 1SLX + 0.3SLY42.751
+ 0.3SLZ 17.436 5.908 50.658 120.984
Min Mz 13348 1152 1DL11410
+ 1SIDL 1573.157
- 1COL(-X)-MLC-65.928 -0.683 -2.328 4.708 -235.217

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13348 3171 1.15DL
11410
+ 1.2SIDL
3947.749
+ 0.42CL14.726
+ 0.42PLB +62.194
0.462TLB4.558
+ 0.462BTB
171.256
+ 0.3SLX +42.543
0.3SLY + 1SLZ + 1.
Min Fx 13348 2115 1.15DL
11411
+ 1.2SIDL
-1693.115
+ 0.3SLX +-19.42
0.3SLY + 1SLZ
-63.973 -4.575 -100.838 -34.935
Max Fy 13348 2104 1.15DL
11410
+ 1.2SIDL
2708.694
+ 1.4CL +85.864
1.4PLB + 1.54TLB
4.017 - 1.54BTB
10.237 20.387 242.096
Min Fy 13348 1452 1.15DL
11410
+ 1.2SIDL
2029.831
- 1.5COL(-X)-MLC
-98.357 -0.866 -3.483 6.219 -351.511
Max Fz 13348 3147 1.15DL
11410
+ 1.2SIDL
3888.686
+ 0.42CL14.724
+ 0.42PLA +63.626
0.462TLA + 4.56
0.462BTA
167.557
+ 0.3SLX 42.545
+ 0.3SLY + 1SLZ + 1.5
Min Fz 13348 3171 1.15DL
11411
+ 1.2SIDL
-1606.058
+ 0.42CL-20.599
+ 0.42PLB +-64.708
0.462TLB-4.531
+ 0.462BTB
-99.48
+ 0.3SLX-36.914
+ 0.3SLY + 1SLZ + 1.
Max Mx 13348 2103 1.15DL
11410
+ 1.2SIDL
2821.444
+ 1.4CL +79.386
1.4PLB + 1.54TLB
4.203 + 10.273
1.54BTB 20.178 224.479
Min Mx 13348 2104 1.15DL
11411
+ 1.2SIDL
-332.671
+ 1.4CL -84.314
+ 1.4PLB + 1.54TLB
-6.508 - 1.54BTB
-10.3 -6.401 -152.267
Max My 13348 1453 1.15DL
11410
+ 1.2SIDL
2366.82
+ 1.5COL(Z)-MLC
-1.308 -63.025 0.502 207.483 -2.896
Min My 13348 2154 1.15DL
11410
+ 1.2SIDL
-1681.968
+ 0.42CL -18.68
+ 0.42PLA +-63.734
0.462TLA --4.58
0.462BTA
-164.15
- 0.3SLX - 0.3SLY
-52.28 - 1SLZ
Max Mz 13348 2104 1.15DL
11410
+ 1.2SIDL
2708.694
+ 1.4CL +85.864
1.4PLB + 1.54TLB
4.017 - 1.54BTB
10.237 20.387 242.096
Min Mz 13348 1452 1.15DL
11410
+ 1.2SIDL
2029.831
- 1.5COL(-X)-MLC
-98.357 -0.866 -3.483 6.219 -351.511

ODE MDE
Maximum Tension Force (kN) -1269.37 -1693.12
Skin Friction (kN) 2684.00
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


16 18

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 351.6 573 0.614 OK
Minima 3889 172.9 1551 0.112 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 35.96 OK
Minima -96.68 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 0.000 N/mm2


Steel 0.75fy 0.000 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 1.565 OK 10.87 OK
Minima 1.115 OK 8.109 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Naushad
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.758 m
Hence de = 0.741 m and dv = 0.667 m
Horizontal resultant shear force at the section, Vu = 517 kN
Corresponding axial compressive force, N = 2030 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 14476 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0072 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 1.085 %
Horizontal shear force, Vu = 517 kN
Shear stress (vv = Vu /(bv . dv) = 774.83 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.759 Mpa
= 759 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.930
Allowable shear stress in concrete, s vc = 706.257 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.13
Modified shear strength of concrete (n s vc ) = 797.52 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = -15.14 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 266.86 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C57


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN C57

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 7854 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13467 1005 1DL11529
+ 1SIDL 2131.909
+ 1CL + 1PLA + 9.537
1PLB + 1.1TLA
25.377
+ 1.1TLB
-0.239
+ 1.1BTA-55.786
+ 1.1BTB -76.172
Min Fx 13467 1006 1DL11529
+ 1SIDL 1639.756
+ 1CL + 1PLA + 1PLB
0.76+ 1.1TLA
16.054
+ 1.1TLB
-1.262
- 1.1BTA -40.063
- 1.1BTB 26.78
Max Fy 13496 1005 1DL11528
+ 1SIDL 2131.909
+ 1CL + 1PLA +30.161
1PLB + 1.1TLA
41.361
+ 1.1TLB
-0.239
+ 1.1BTA-163.281
+ 1.1BTB -8.571
Min Fy 13496 1006 1DL11528
+ 1SIDL 1639.756
+ 1CL + 1PLA +-2.539
1PLB + 1.1TLA
25.448
+ 1.1TLB
-1.262
- 1.1BTA-106.729
- 1.1BTB 22.968
Max Fz 13496 1005 1DL11528
+ 1SIDL 2131.909
+ 1CL + 1PLA +30.161
1PLB + 1.1TLA
41.361
+ 1.1TLB
-0.239
+ 1.1BTA-163.281
+ 1.1BTB -8.571
Min Fz 13470 1006 1DL11532
+ 1SIDL 1639.756
+ 1CL + 1PLA + 2.178
1PLB + 1.1TLA
9.049
+ 1.1TLB
-1.262
- 1.1BTA - 1.1BTB
0.463 22.761
Max Mx 13467 1001 1DL11529
+ 1SIDL 1956.236
+ 1CL + 1PLA + 7.123
1.1TLA + 21.481
1.1BTA -0.18 -58.517 -49.712
Min Mx 13467 1006 1DL11529
+ 1SIDL 1639.756
+ 1CL + 1PLA + 1PLB
0.76+ 1.1TLA
16.054
+ 1.1TLB
-1.262
- 1.1BTA -40.063
- 1.1BTB 26.78
Max My 13470 1003 1DL11533
+ 1SIDL 2013.498
+ 1CL + 1PLB +-0.665
1.1TLB + 12.128
1.1BTB -0.611 28.437 -62.207
Min My 13496 1005 1DL11528
+ 1SIDL 2131.909
+ 1CL + 1PLA +30.161
1PLB + 1.1TLA
41.361
+ 1.1TLB
-0.239
+ 1.1BTA-163.281
+ 1.1BTB -8.571
Max Mz 13467 1006 1DL11529
+ 1SIDL 1639.756
+ 1CL + 1PLA + 1PLB
0.76+ 1.1TLA
16.054
+ 1.1TLB
-1.262
- 1.1BTA -40.063
- 1.1BTB 26.78
Min Mz 13469 1005 1DL11532
+ 1SIDL 2131.909
+ 1CL + 1PLA + 1.203
1PLB + 1.1TLA
17.088
+ 1.1TLB
-0.239
+ 1.1BTA +7.638
1.1BTB -91.807

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13467 1079 1DL11529
+ 1SIDL 4053.191
+ 0.3CL + 0.3PLA
54.303
+ 0.3PLB81.147
+ 0.33TLA +4.369
0.33TLB +285.374
0.33BTA + 417.278
0.33BTB + 1SLX + 0.3S
Min Fx 13467 1007 1DL11530
+ 1SIDL +-717.707
1SLX + 0.3SLY
-44.564
+ 0.3SLZ -46.74 -5.314 -305.465 -521.737
Max Fy 13496 1152 1DL11528
+ 1SIDL 3571.862
- 1COL(-X)-MLC331.532 86.751 1.407 -336.667 670.381
Min Fy 13496 1086 1DL11528
+ 1SIDL +-701.529
0.3CL + 0.3PLA
-156.324
+ 0.3PLB
-103.139
+ 0.33TLA +-5.538
0.33TLB-557.666
- 0.33BTA - 0.33BTB
-83.48- 1SLX - 0.3SLY
Max Fz 13496 1153 1DL11528
+ 1SIDL 1599.223
+ 1COL(Z)-MLC 10.684 247.173 -1.229 -481.409 7.416
Min Fz 13496 1054 1DL11528
+ 1SIDL +769.957
0.3CL + 0.3PLA
-43.029
+ 0.33TLA
-162.519
- 0.33BTA-4.1
- 0.3SLX
-598.462
- 0.3SLY - 1SLZ
-24.054
Max Mx 13467 3055 1DL11529
+ 1SIDL +4017.23
0.3CL + 0.3PLB
53.595
+ 0.33TLB80.766
+ 0.33BTB
4.421
+ 1SLX +294.21
0.3SLY + 0.3SLZ
425.542+ 1.1NLB
Min Mx 13467 3062 1DL11529
+ 1SIDL +-663.302
0.3CL + 0.3PLB
-44.849
+ 0.33TLB
-45.915
- 0.33BTB
-5.623
- 1SLX-367.505
- 0.3SLY - 0.3SLZ
-464.668
- 1.1NLB
Max My 13468 3071 1DL11530
+ 1SIDL 2567.374
+ 0.3CL + 0.3PLB10.57
+ 0.33TLB49.075
+ 0.33BTB
3.118
+ 0.3SLX
684.433
+ 0.3SLY +126.694
1SLZ + 1.1NLB
Min My 13497 3047 1DL11529
+ 1SIDL +843.708
0.3CL + 0.3PLA
-18.18
+ 0.33TLA
-70.652
+ 0.33BTA
-4.074
+ 0.3SLX
-741.419
+ 0.3SLY-171.612
+ 1SLZ + 1.1NLA
Max Mz 13496 1152 1DL11528
+ 1SIDL 3571.862
- 1COL(-X)-MLC331.532 86.751 1.407 -336.667 670.381
Min Mz 13469 1079 1DL11532
+ 1SIDL +-553.883
0.3CL + 0.3PLA
-1.643
+ 0.3PLB-30.421
+ 0.33TLA +-5.231
0.33TLB-214.153
+ 0.33BTA +-570.028
0.33BTB + 1SLX + 0.3S
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13467 2103 1.15DL
11529
+ 1.2SIDL
6757.066
+ 1.4CL101.825
+ 1.4PLB + 1.54TLB
112.33 + 1.54BTB
7.366 157.432 802.85
Min Fx 13467 2104 1.15DL
11530
+ 1.2SIDL
-2270.29
+ 1.4CL -89.587
+ 1.4PLB + 1.54TLB
-61.834 - 1.54BTB
-8.962 -159.261 -956.895
Max Fy 13496 1452 1.15DL
11528
+ 1.2SIDL
4802.717
- 1.5COL(-X)-MLC
493.593 121.219 2.289 -469.103 1003.143
Min Fy 13496 2104 1.15DL
11559
+ 1.2SIDL
-2270.29
+ 1.4CL-307.396
+ 1.4PLB + 1.54TLB
-96.724 - 1.54BTB
-8.962 -530.317 -474.617
Max Fz 13496 1453 1.15DL
11528
+ 1.2SIDL
1843.759
+ 1.5COL(Z)-MLC
12.32 361.853 -1.664 -686.217 8.695
Min Fz 13496 2154 1.15DL
11528
+ 1.2SIDL
804.681
+ 0.42CL-55.369
+ 0.42PLA-205.348
+ 0.462TLA-5.102
- 0.462BTA
-733.299
- 0.3SLX --30.316
0.3SLY - 1SLZ
Max Mx 13467 2103 1.15DL
11529
+ 1.2SIDL
6757.066
+ 1.4CL101.825
+ 1.4PLB + 1.54TLB
112.33 + 1.54BTB
7.366 157.432 802.85
Min Mx 13467 2104 1.15DL
11530
+ 1.2SIDL
-2270.29
+ 1.4CL -89.587
+ 1.4PLB + 1.54TLB
-61.834 - 1.54BTB
-8.962 -159.261 -956.895
Max My 13468 3171 1.15DL
11530
+ 1.2SIDL
3074.597
+ 0.42CL13.036
+ 0.42PLB +58.791
0.462TLB3.982
+ 0.462BTB
860.977
+ 0.3SLX160.001
+ 0.3SLY + 1SLZ + 1.
Min My 13497 3147 1.15DL
11529
+ 1.2SIDL
907.931
+ 0.42CL-23.189
+ 0.42PLA +-89.165
0.462TLA-5.065
+ 0.462BTA
-926.53
+ 0.3SLX-215.117
+ 0.3SLY + 1SLZ + 1.5
Max Mz 13470 2104 1.15DL
11532
+ 1.2SIDL
6410.177
+ 1.4CL + 1.4PLB
26.78 + 1.54TLB
59.212 - 1.54BTB
6.819 52.369 1008.942
Min Mz 13469 2103 1.15DL
11532
+ 1.2SIDL
-1923.402
+ 1.4CL +-3.245
1.4PLB + 1.54TLB
-38.931 + 1.54BTB
-8.414 -30.998 -1090.768

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 2131.909 1639.756 7790.000 OK
ODE Seismic 4053.191 -717.707 7854.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 36 16
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -1923 1091 1556 0.701 OK
Minima 1844 686.3 2407 0.285 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 64.19 OK
Minima -170.7 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 3.874 OK 24.91 OK
Minima 0.8733 OK 8.083 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 17.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13481 1005 1DL11543
+ 1SIDL 2131.909
+ 1CL + 1PLA +-5.678
1PLB + 1.1TLA
-5.61
+ 1.1TLB
-0.239
+ 1.1BTA +22.468
1.1BTB -13.018
Min Fx 13481 1006 1DL11543
+ 1SIDL 1639.756
+ 1CL + 1PLA + 0.755
1PLB + 1.1TLA
-3.374
+ 1.1TLB
-1.262
- 1.1BTA -13.989
1.1BTB 0.509
Max Fy 28524 1005 1DL27508
+ 1SIDL 2131.909
+ 1CL + 1PLA + 0.944
1PLB + 1.1TLA
0.465
+ 1.1TLB
-0.239
+ 1.1BTA +-1.884
1.1BTB 2.839
Min Fy 13481 1005 1DL11543
+ 1SIDL 2131.909
+ 1CL + 1PLA +-5.678
1PLB + 1.1TLA
-5.61
+ 1.1TLB
-0.239
+ 1.1BTA +22.468
1.1BTB -13.018
Max Fz 28525 1003 1DL27509
+ 1SIDL 2013.498
+ 1CL + 1PLB + 0.605
1.1TLB + 1.1BTB
0.599 -0.611 -1.463 1.34
Min Fz 13481 1005 1DL11543
+ 1SIDL 2131.909
+ 1CL + 1PLA +-5.678
1PLB + 1.1TLA
-5.61
+ 1.1TLB
-0.239
+ 1.1BTA +22.468
1.1BTB -13.018
Max Mx 13481 1001 1DL11543
+ 1SIDL 1956.236
+ 1CL + 1PLA +-3.977
1.1TLA + -4.334
1.1BTA -0.18 18.487 -9.385
Min Mx 13481 1006 1DL11543
+ 1SIDL 1639.756
+ 1CL + 1PLA + 0.755
1PLB + 1.1TLA
-3.374
+ 1.1TLB
-1.262
- 1.1BTA -13.989
1.1BTB 0.509
Max My 13481 1005 1DL11543
+ 1SIDL 2131.909
+ 1CL + 1PLA +-5.678
1PLB + 1.1TLA
-5.61
+ 1.1TLB
-0.239
+ 1.1BTA +22.468
1.1BTB -13.018
Min My 28522 1003 1DL27507
+ 1SIDL 2013.498
+ 1CL + 1PLB + 0.409
1.1TLB + 1.1BTB
-0.24 -0.611 -2.221 2.606
Max Mz 28520 1005 1DL27505
+ 1SIDL 2131.909
+ 1CL + 1PLA +-0.818
1PLB + 1.1TLA
-2.179
+ 1.1TLB
-0.239
+ 1.1BTA +-0.605
1.1BTB 4.414
Min Mz 13481 1005 1DL11543
+ 1SIDL 2131.909
+ 1CL + 1PLA +-5.678
1PLB + 1.1TLA
-5.61
+ 1.1TLB
-0.239
+ 1.1BTA +22.468
1.1BTB -13.018
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13481 1079 1DL11543
+ 1SIDL 4053.191
+ 0.3CL + 0.3PLA
28.186
+ 0.3PLB16.441
+ 0.33TLA +4.369
0.33TLB + 79.913
0.33BTA + 0.33BTB
61.958 + 1SLX + 0.3S
Min Fx 13481 1007 1DL11544
+ 1SIDL +-717.707
1SLX + 0.3SLY
-33.066
+ 0.3SLZ -23.948 -5.314 -32.744 -41.013
Max Fy 13481 1086 1DL11544
+ 1SIDL 3905.545
+ 0.3CL + 0.3PLA
30.115
+ 0.3PLB17.112
+ 0.33TLA +4.062
0.33TLB - 0.33BTA
53.7 - 0.33BTB
35.903- 1SLX - 0.3SLY
Min Fy 13481 1152 1DL11543
+ 1SIDL 3571.862
- 1COL(-X)-MLC-52.904 -11.839 1.407 46.972 -163.261
Max Fz 13481 1054 1DL11544
+ 1SIDL +2477.32
0.3CL + 0.3PLA
8.378
+ 0.33TLA 33.189
- 0.33BTA
2.895
- 0.3SLX53.872
- 0.3SLY - 1SLZ
9.611
Min Fz 13481 3071 1DL11544
+ 1SIDL +860.011
0.3CL + 0.3PLB
-12.419
+ 0.33TLB-40.836
+ 0.33BTB
-3.877
+ 0.3SLX-31.04
+ 0.3SLY +-15.958
1SLZ + 1.1NLB
Max Mx 13481 3055 1DL11543
+ 1SIDL +4017.23
0.3CL + 0.3PLB
28.703
+ 0.33TLB 16.231
+ 0.33BTB
4.421
+ 1SLX +79.953
0.3SLY + 0.3SLZ
63.047+ 1.1NLB
Min Mx 13481 3062 1DL11543
+ 1SIDL +-663.302
0.3CL + 0.3PLB
-32.781
+ 0.33TLB-24.058
- 0.33BTB
-5.623
- 1SLX - 0.3SLY
-48.94 - 0.3SLZ
-73.539
- 1.1NLB
Max My 13481 1153 1DL11543
+ 1SIDL 1599.223
+ 1COL(Z)-MLC-1.881 -39.671 -1.229 121.234 -4.887
Min My 13481 1022 1DL11543
+ 1SIDL - 732.148
0.3SLX - 0.3SLY
-11.793
- 1SLZ -39.971 -4.011 -65.12 -27.005
Max Mz 13481 1007 1DL11543
+ 1SIDL 3889.367
+ 1SLX + 0.3SLY29.328
+ 0.3SLZ 17.096 4.287 77.337 64.414
Min Mz 13481 1152 1DL11543
+ 1SIDL 3571.862
- 1COL(-X)-MLC-52.904 -11.839 1.407 46.972 -163.261

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 13481 2103 1.15DL
11543
+ 1.2SIDL
6757.066
+ 1.4CL +54.664
1.4PLB + 1.54TLB
11.19 + 1.54BTB
7.366 98.476 120.255
Min Fx 13481 2104 1.15DL
11544
+ 1.2SIDL
-2270.29
+ 1.4CL -60.505
+ 1.4PLB + 1.54TLB
-22.601 - 1.54BTB
-8.962 -40.787 -74.605
Max Fy 13481 2104 1.15DL
11543
+ 1.2SIDL
6410.177
+ 1.4CL +59.212
1.4PLB + 1.54TLB
12.719 - 1.54BTB
6.819 92.58 129.824
Min Fy 13481 1452 1.15DL
11543
+ 1.2SIDL
4802.717
- 1.5COL(-X)-MLC
-78.702 -16.559 2.289 65.6 -243.2
Max Fz 13481 2154 1.15DL
11544
+ 1.2SIDL
2948.522
+ 0.42CL10.767
+ 0.42PLA +41.881
0.462TLA - 3.67
0.462BTA65.752
- 0.3SLX - 12.412
0.3SLY - 1SLZ
Min Fz 13481 1453 1.15DL
11543
+ 1.2SIDL
1843.759
+ 1.5COL(Z)-MLC
-2.168 -58.308 -1.664 176.993 -5.639
Max Mx 13481 2103 1.15DL
11543
+ 1.2SIDL
6757.066
+ 1.4CL +54.664
1.4PLB + 1.54TLB
11.19 + 1.54BTB
7.366 98.476 120.255
Min Mx 13481 2104 1.15DL
11544
+ 1.2SIDL
-2270.29
+ 1.4CL -60.505
+ 1.4PLB + 1.54TLB
-22.601 - 1.54BTB
-8.962 -40.787 -74.605
Max My 13481 1453 1.15DL
11543
+ 1.2SIDL
1843.759
+ 1.5COL(Z)-MLC
-2.168 -58.308 -1.664 176.993 -5.639
Min My 13481 2122 1.15DL
11543
+ 1.2SIDL
751.748
- 0.3SLX-14.613
- 0.3SLY - 1SLZ
-49.663 -4.977 -82.357 -33.385
Max Mz 13481 2104 1.15DL
11543
+ 1.2SIDL
6410.177
+ 1.4CL +59.212
1.4PLB + 1.54TLB
12.719 - 1.54BTB
6.819 92.58 129.824
Min Mz 13481 1452 1.15DL
11543
+ 1.2SIDL
4802.717
- 1.5COL(-X)-MLC
-78.702 -16.559 2.289 65.6 -243.2

ODE MDE
Maximum Tension Force (kN) -717.71 -2270.29
Skin Friction (kN) 1770.00
Final Axial Load (kN) 0.00 -500.29

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 251.9 513.4 0.491 OK
Minima 2949 66.92 1326 0.050 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 40.94 OK
Minima -8.375 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 2.907 OK 20.19 OK
Minima 1.897 OK 13.86 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.756 m
Hence de = 0.741 m and dv = 0.667 m
Horizontal resultant shear force at the section, Vu = 508 kN
Corresponding axial compressive force, N = 4803 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 16286 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0081 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 1.222 %
Horizontal shear force, Vu = 508 kN
Shear stress (vv = Vu /(bv . dv) = 762.49 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.790 Mpa
= 790 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.931
Allowable shear stress in concrete, s vc = 734.905 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.31
Modified shear strength of concrete (n s vc ) = 959.60 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = -131.39 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 266.63 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP PG1B


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR COLUMN PG-1B

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 1
Pile Diameter = 1.0 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 7790 kN
Seismic Case (ODE) = 7854 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26932 1005 1DL25880
+ 1SIDL + 1CL
692.01
+ 1PLA +71.883
1PLB + 1.1TLA
6.247
+ 1.1TLB
28.113
+ 1.1BTA +6.357
1.1BTB 25.764
Min Fx 26982 1006 1DL25939
+ 1SIDL +570.584
1CL + 1PLA +24.201
1PLB + 1.1TLA
1.312
+ 1.1TLB3.878
- 1.1BTA - -2.235
1.1BTB 91.179
Max Fy 26949 1005 1DL25879
+ 1SIDL + 1CL
692.01
+ 1PLA137.062
+ 1PLB + 1.1TLA
13.205
+ 1.1TLB
28.113
+ 1.1BTA-25.732
+ 1.1BTB 367.293
Min Fy 27024 1006 1DL25967
+ 1SIDL +627.597
1CL + 1PLA -74.728
+ 1PLB + 1.1TLA
3.469
+ 1.1TLB
-4.571
- 1.1BTA - -3.906
1.1BTB -217.647
Max Fz 26949 1006 1DL25879
+ 1SIDL +649.492
1CL + 1PLA +73.886
1PLB + 1.1TLA
13.612
+ 1.1TLB
27.309
- 1.1BTA - -23.38
1.1BTB 391.714
Min Fz 26922 1001 1DL25849
+ 1SIDL +611.352
1CL + 1PLA +-6.181
1.1TLA + -73.917
1.1BTA -3.334 32.994 -20.625
Max Mx 26932 1001 1DL25880
+ 1SIDL +682.795
1CL + 1PLA +67.577
1.1TLA + 1.1BTA
6.265 28.878 3.964 65.896
Min Mx 27007 1006 1DL25968
+ 1SIDL +627.597
1CL + 1PLA -40.414
+ 1PLB + 1.1TLA
1.441
+ 1.1TLB
-4.571
- 1.1BTA - 1.1BTB
4.283 -29.97
Max My 26922 1004 1DL25849
+ 1SIDL +594.823
1CL + 1PLB -10.807
+ 1.1TLB - -59.515
1.1BTB -2.295 47.023 -5.626
Min My 26908 1002 1DL25854
+ 1SIDL +610.095
1CL + 1PLA +-0.218
1.1TLA - 1.1BTA
-0.754 -2.698 -189.89 30.646
Max Mz 26949 1006 1DL25879
+ 1SIDL +649.492
1CL + 1PLA +73.886
1PLB + 1.1TLA
13.612
+ 1.1TLB
27.309
- 1.1BTA - -23.38
1.1BTB 391.714
Min Mz 27024 1005 1DL25967
+ 1SIDL + 1CL
589.93
+ 1PLA -15.587
+ 1PLB + 1.1TLA 2.6
+ 1.1TLB
-4.101
+ 1.1BTA +-5.602
1.1BTB -263.667

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26932 1079 1DL25880
+ 1SIDL +801.701
0.3CL + 0.3PLA
140.482
+ 0.3PLB +9.197
0.33TLA 28.132
+ 0.33TLB + 88.583
0.33BTA + 781.246
0.33BTB + 1SLX + 0.3S
Min Fx 26905 1015 1DL25851
+ 1SIDL +296.559
0.3SLX + 0.3SLY
-7.817
+ 1SLZ -82.351 -12.979 -1212.713 -97.484
Max Fy 26949 1079 1DL25879
+ 1SIDL +801.701
0.3CL + 0.3PLA
371.719
+ 0.3PLB30.707
+ 0.33TLA 28.132
+ 0.33TLB + 23.027
0.33BTA + 427.582
0.33BTB + 1SLX + 0.3S
Min Fy 27024 1086 1DL25967
+ 1SIDL +386.761
0.3CL + 0.3PLA
-318.956
+ 0.3PLB-15.834
+ 0.33TLA +-6.442
0.33TLB --36.991
0.33BTA - -407.463
0.33BTB - 1SLX - 0.3SLY
Max Fz 26922 3071 1DL25849
+ 1SIDL +780.396
0.3CL + 0.3PLB
18.465
+ 0.33TLB
225.166
+ 0.33BTB
8.269
+ 0.3SLX
483.837
+ 0.3SLY + 37.304
1SLZ + 1.1NLB
Min Fz 26922 3047 1DL25868
+ 1SIDL +323.105
0.3CL + 0.3PLA
-31.497
+ 0.33TLA
-340.096
+ 0.33BTA
-13.286
+ 0.3SLX
-758.872
+ 0.3SLY +-81.494
1SLZ + 1.1NLA
Max Mx 26932 1001 1DL25880
+ 1SIDL +682.795
1CL + 1PLA +67.577
1.1TLA + 1.1BTA
6.265 28.878 3.964 65.896
Min Mx 26905 1095 1DL25851
+ 1SIDL +320.356
0.3CL + 0.3PLA-7.82
+ 0.3PLB-84.273
+ 0.33TLA-13.436
+ 0.33TLB -1224.231
+ 0.33BTA +-104.656
0.33BTB + 0.3SLX + 0.
Max My 26907 3071 1DL25852
+ 1SIDL +780.396
0.3CL + 0.3PLB
1.288
+ 0.33TLB 14.294
+ 0.33BTB
8.269
+ 0.3SLX
996.958
+ 0.3SLY +114.868
1SLZ + 1.1NLB
Min My 26906 3047 1DL25852
+ 1SIDL +323.105
0.3CL + 0.3PLA-3.15
+ 0.33TLA-29.127
+ 0.33BTA
-13.286
+ 0.3SLX
-1266.621
+ 0.3SLY +-98.558
1SLZ + 1.1NLA
Max Mz 27009 1086 1DL25971
+ 1SIDL +732.465
0.3CL + 0.3PLA
-19.276
+ 0.3PLB +2.246
0.33TLA +-0.731
0.33TLB - 0.33BTA
79.954 - 0.33BTB
920.348- 1SLX - 0.3SLY
Min Mz 27008 1079 1DL25970
+ 1SIDL +375.461
0.3CL + 0.3PLA
-55.693
+ 0.3PLB +0.035
0.33TLA +-6.301
0.33TLB +-73.405
0.33BTA +-995.869
0.33BTB + 1SLX + 0.3S
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26932 2103 1.15DL
25880
+ 1.2SIDL
1149.331
+ 1.4CL239.189
+ 1.4PLB + 1.54TLB
8.077 + 1.54BTB
38.95 37.01 1437.913
Min Fx 26905 2115 1.15DL
25851
+ 1.2SIDL
316.461
+ 0.3SLX +-9.497
0.3SLY +-101.284
1SLZ -16.061 -1510.729 -123.468
Max Fy 26949 2103 1.15DL
25879
+ 1.2SIDL
1149.331
+ 1.4CL661.601
+ 1.4PLB + 1.54TLB
20.148 + 1.54BTB
38.95 -7.461 637.756
Min Fy 27024 2104 1.15DL
25986
+ 1.2SIDL
400.42
+ 1.4CL -598.81
+ 1.4PLB + 1.54TLB
-4.202 - -10.124
1.54BTB -22.73 -1130.422
Max Fz 26922 3171 1.15DL
25849
+ 1.2SIDL
926.618
+ 0.42CL24.017
+ 0.42PLB 288.338
+ 0.462TLB 10.582
+ 0.462BTB
605.545
+ 0.3SLX +47.505
0.3SLY + 1SLZ + 1.
Min Fz 26922 3147 1.15DL
25868
+ 1.2SIDL
353.626
+ 0.42CL-38.812
+ 0.42PLA-422.631
+ 0.462TLA -16.492
+ 0.462BTA
-952.049
+ 0.3SLX-102.497
+ 0.3SLY + 1SLZ + 1.5
Max Mx 26932 2103 1.15DL
25880
+ 1.2SIDL
1149.331
+ 1.4CL239.189
+ 1.4PLB + 1.54TLB
8.077 + 1.54BTB
38.95 37.01 1437.913
Min Mx 26905 2195 1.15DL
25851
+ 1.2SIDL
349.776
+ 0.42CL -9.501
+ 0.42PLA-103.975
+ 0.42PLB +-16.701
0.462TLA-1526.854
+ 0.462TLB +-133.509
0.462BTA + 0.462BTB
Max My 26907 3171 1.15DL
25852
+ 1.2SIDL
926.618
+ 0.42CL +1.727
0.42PLB +18.484
0.462TLB10.582
+ 0.462BTB
1265.946
+ 0.3SLX142.501
+ 0.3SLY + 1SLZ + 1.
Min My 26906 3147 1.15DL
25852
+ 1.2SIDL
353.626
+ 0.42CL -3.763
+ 0.42PLA +-35.462
0.462TLA-16.492
+ 0.462BTA
-1580.892
+ 0.3SLX-125.424
+ 0.3SLY + 1SLZ + 1.5
Max Mz 27010 2104 1.15DL
25971
+ 1.2SIDL
1066.067
+ 1.4CL +29.492
1.4PLB + 1.54TLB
1.82 - 1.54BTB
-0.674 42.719 1798.426
Min Mz 27008 2103 1.15DL
25970
+ 1.2SIDL
373.858
+ 1.4CL -95.023
+ 1.4PLB + 1.54TLB
0.675 + 1.54BTB
-9.89 -27.729 -1908.193

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 692.01 570.584 7790.000 OK
ODE Seismic 801.701 296.559 7854.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 0.785 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.318 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 16
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 373.9 1908 2335 0.817 OK
Minima 926.6 607.4 2424 0.251 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 75.85 OK
Minima -221.1 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 5.415 OK 25.18 OK
Minima -1.718 OK -27.29 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.093 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 17.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26946 1005 1DL25894
+ 1SIDL + 1CL
692.01
+ 1PLA -20.751
+ 1PLB + 1.1TLA
-2.119
+ 1.1TLB
28.113
+ 1.1BTA +6.477
1.1BTB -69.872
Min Fx 26996 1006 1DL25953
+ 1SIDL +570.584
1CL + 1PLA +-3.955
1PLB + 1.1TLA
-0.314
+ 1.1TLB3.878
- 1.1BTA - 1.1BTB
1.192 -19.638
Max Fy 27021 1006 1DL25982
+ 1SIDL +627.597
1CL + 1PLA +11.098
1PLB + 1.1TLA
-0.592
+ 1.1TLB
-4.571
- 1.1BTA - 1.1BTB
1.626 38.554
Min Fy 26946 1005 1DL25894
+ 1SIDL + 1CL
692.01
+ 1PLA -20.751
+ 1PLB + 1.1TLA
-2.119
+ 1.1TLB
28.113
+ 1.1BTA +6.477
1.1BTB -69.872
Max Fz 26919 1001 1DL25864
+ 1SIDL +611.352
1CL + 1PLA + 0.885
1.1TLA + 13.243
1.1BTA -3.334 -33.329 3.258
Min Fz 26946 1006 1DL25894
+ 1SIDL +649.492
1CL + 1PLA +-8.778
1PLB + 1.1TLA
-2.224
+ 1.1TLB
27.309
- 1.1BTA - 1.1BTB
6.594 -42.774
Max Mx 26946 1001 1DL25894
+ 1SIDL +682.795
1CL + 1PLA -17.977
+ 1.1TLA + -2.037
1.1BTA 28.878 6.382 -63.725
Min Mx 27021 1006 1DL25982
+ 1SIDL +627.597
1CL + 1PLA +11.098
1PLB + 1.1TLA
-0.592
+ 1.1TLB
-4.571
- 1.1BTA - 1.1BTB
1.626 38.554
Max My 28980 1002 1DL27965
+ 1SIDL +610.095
1CL + 1PLA + 0.036
1.1TLA - 1.1BTA
0.175 -2.698 9.34 -1.512
Min My 26919 1001 1DL25864
+ 1SIDL +611.352
1CL + 1PLA + 0.885
1.1TLA + 13.243
1.1BTA -3.334 -33.329 3.258
Max Mz 27021 1006 1DL25982
+ 1SIDL +627.597
1CL + 1PLA +11.098
1PLB + 1.1TLA
-0.592
+ 1.1TLB
-4.571
- 1.1BTA - 1.1BTB
1.626 38.554
Min Mz 26946 1005 1DL25894
+ 1SIDL + 1CL
692.01
+ 1PLA -20.751
+ 1PLB + 1.1TLA
-2.119
+ 1.1TLB
28.113
+ 1.1BTA +6.477
1.1BTB -69.872
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26946 1079 1DL25894
+ 1SIDL +801.701
0.3CL + 0.3PLA
38.022
+ 0.3PLB +2.436
0.33TLA 28.132
+ 0.33TLB + 12.992
0.33BTA + 0.33BTB
67.347 + 1SLX + 0.3S
Min Fx 26919 1015 1DL25865
+ 1SIDL +296.559
0.3SLX + 0.3SLY
-4.045
+ 1SLZ -47.49 -12.979 -68.276 -2.196
Max Fy 27021 1086 1DL25983
+ 1SIDL +732.465
0.3CL + 0.3PLA
59.111
+ 0.3PLB +3.383
0.33TLA +-0.731
0.33TLB - 0.33BTA
4.203 - 0.33BTB
80.533- 1SLX - 0.3SLY
Min Fy 26946 1079 1DL25895
+ 1SIDL +428.021
0.3CL + 0.3PLA
-65.917
+ 0.3PLB -5.917
+ 0.33TLA 16.916
+ 0.33TLB + 0.33BTA
-0.062 + 0.33BTB
-103.14 + 1SLX + 0.3S
Max Fz 26919 3047 1DL25864
+ 1SIDL +788.509
0.3CL + 0.3PLA6.281
+ 0.33TLA 68.006
+ 0.33BTA 8.207
+ 0.3SLX82.665
+ 0.3SLY +12.848
1SLZ + 1.1NLA
Min Fz 26919 3071 1DL25865
+ 1SIDL +314.992
0.3CL + 0.3PLB -4.2
+ 0.33TLB-47.602
+ 0.33BTB
-13.225+ 0.3SLX
-68.609
+ 0.3SLY + 1SLZ
-2.237
+ 1.1NLB
Max Mx 26946 1001 1DL25894
+ 1SIDL +682.795
1CL + 1PLA -17.977
+ 1.1TLA + -2.037
1.1BTA 28.878 6.382 -63.725
Min Mx 26919 1095 1DL25865
+ 1SIDL +320.356
0.3CL + 0.3PLA
-4.308
+ 0.3PLB-46.557
+ 0.33TLA-13.436
+ 0.33TLB +-69.696
0.33BTA + 0.33BTB
-2.268 + 0.3SLX + 0.
Max My 26919 1015 1DL25864
+ 1SIDL +761.963
0.3SLX + 0.3SLY
6.347
+ 1SLZ 66.387 8.515 86.347 12.838
Min My 26919 1054 1DL25864
+ 1SIDL +320.809
0.3CL + 0.3PLA
-3.741
+ 0.33TLA-46.355
- 0.33BTA
-13.118
- 0.3SLX
-137.376
- 0.3SLY - 1SLZ
-5.583
Max Mz 27021 1007 1DL25982
+ 1SIDL +703.329
1SLX + 0.3SLY
57.064
+ 0.3SLZ 3.45 -0.309 8.284 134.252
Min Mz 26946 1038 1DL25894
+ 1SIDL + 0.3CL
418.82
+ 0.3PLA
-63.272
+ 0.33TLA -5.909
- 0.33BTA
16.988
- 1SLX - -2.438
0.3SLY - 0.3SLZ
-163.107

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 26946 2103 1.15DL
25894
+ 1.2SIDL
1149.331
+ 1.4CL +77.565
1.4PLB + 1.54TLB
-1.3 + 1.54BTB
38.95 9.202 148.737
Min Fx 26919 2115 1.15DL
25865
+ 1.2SIDL
316.461
+ 0.3SLX +-5.204
0.3SLY + 1SLZ
-60.626 -16.061 -84.171 -2.985
Max Fy 27021 2104 1.15DL
25982
+ 1.2SIDL
1066.067
+ 1.4CL112.274
+ 1.4PLB + 1.54TLB
1.005 - 1.54BTB
-0.674 5.366 259.414
Min Fy 26946 2103 1.15DL
25895
+ 1.2SIDL
451.643
+ 1.4CL-119.236
+ 1.4PLB + 1.54TLB
-3.58 + 22.524
1.54BTB 3.973 -177.585
Max Fz 26919 3147 1.15DL
25864
+ 1.2SIDL
937.977
+ 0.42CL + 0.42PLA
7.76 +84.622
0.462TLA10.496
+ 0.462BTA
105.814
+ 0.3SLX 15.791
+ 0.3SLY + 1SLZ + 1.5
Min Fz 26919 3171 1.15DL
25865
+ 1.2SIDL
342.267
+ 0.42CL +-5.42
0.42PLB +-60.782
0.462TLB
-16.405
+ 0.462BTB
-84.637
+ 0.3SLX +-3.042
0.3SLY + 1SLZ + 1.
Max Mx 26946 2103 1.15DL
25894
+ 1.2SIDL
1149.331
+ 1.4CL +77.565
1.4PLB + 1.54TLB
-1.3 + 1.54BTB
38.95 9.202 148.737
Min Mx 26919 2195 1.15DL
25865
+ 1.2SIDL
349.776
+ 0.42CL -5.572
+ 0.42PLA + -59.32
0.42PLB +-16.701
0.462TLA +-86.159
0.462TLB + 0.462BTA
-3.087 + 0.462BTB
Max My 26919 2115 1.15DL
25864
+ 1.2SIDL
900.812
+ 0.3SLX +7.851
0.3SLY + 1SLZ
82.355 10.927 110.968 15.777
Min My 26919 2154 1.15DL
25864
+ 1.2SIDL
350.411
+ 0.42CL -4.778
+ 0.42PLA +-59.037
0.462TLA-16.257
- 0.462BTA
-170.325
- 0.3SLX - 0.3SLY
-7.267 - 1SLZ
Max Mz 27021 2104 1.15DL
25982
+ 1.2SIDL
1066.067
+ 1.4CL112.274
+ 1.4PLB + 1.54TLB
1.005 - 1.54BTB
-0.674 5.366 259.414
Min Mz 26946 1452 1.15DL
25894
+ 1.2SIDL
913.978
- 1.5COL(-X)-MLC
-82.594 -1.947 29.591 6.613 -207.211

ODE MDE
Maximum Tension Force (kN) 296.56 316.461
Skin Friction (kN) 1770.00
Final Axial Load (kN) 0.00 0.00

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


16 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 207.3 511.9 0.405 OK
Minima 938 107 816.4 0.131 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 12.58 OK
Minima -7.688 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 1.562 OK 9.457 OK
Minima 0.1601 OK 2.845 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.00 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.754 m
Hence de = 0.740 m and dv = 0.666 m
Horizontal resultant shear force at the section, Vu = 662 kN
Corresponding axial compressive force, N = 1149 kN
Eff. width to be taken = diameter of section = bv = 1.00 m
Total vertical reinforcement at the section = 20106 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0101 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 1.509 %
Horizontal shear force, Vu = 662 kN
Shear stress (vv = Vu /(bv . dv) = 993.85 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.847 Mpa
= 847 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.931
Allowable shear stress in concrete, s vc = 788.777 kN/m2
Gross area of concrete section, Ac 0.785 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.07
Modified shear strength of concrete (n s vc ) = 846.49 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 98.14 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 266.40 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 225 mm
Provided spacing 220 mm
OK
Shear reinforcement 13mm dia @ 220mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP PG2


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP PG2

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 2
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 27261 1005 1DL26205
+ 1SIDL 2760.485
+ 1CL + 1PLA +22.749
1PLB + 1.1TLA-1.01
+ 1.1TLB
-6.797
+ 1.1BTA +0.846
1.1BTB -63.718
Min Fx 27282 1005 1DL26226
+ 1SIDL 1351.739
+ 1CL + 1PLA +24.904
1PLB + 1.1TLA
4.193
+ 1.1TLB
-4.895
+ 1.1BTA-21.368
+ 1.1BTB -60.814
Max Fy 27299 1005 1DL26225
+ 1SIDL 1351.739
+ 1CL + 1PLA +48.929
1PLB + 1.1TLA
5.179
+ 1.1TLB
-4.895
+ 1.1BTA-35.978
+ 1.1BTB 60.116
Min Fy 27299 1006 1DL26225
+ 1SIDL 1998.458
+ 1CL + 1PLA -58.595
+ 1PLB + 1.1TLA
36.937
+ 1.1TLB6.804
- 1.1BTA-230.838
- 1.1BTB -287.877
Max Fz 27299 1004 1DL26225
+ 1SIDL 1880.876
+ 1CL + 1PLB -35.057
+ 1.1TLB - 1.1BTB
41.374 4.998 -231.596 -219.882
Min Fz 27278 1001 1DL26204
+ 1SIDL 2569.151
+ 1CL + 1PLA + 23.73
1.1TLA + -10.072
1.1BTA -4.008 29.937 -6.736
Max Mx 27282 1006 1DL26226
+ 1SIDL 1998.458
+ 1CL + 1PLA -41.177
+ 1PLB + 1.1TLA
28.553
+ 1.1TLB6.804
- 1.1BTA-128.213
- 1.1BTB -129.865
Min Mx 27261 1005 1DL26205
+ 1SIDL 2760.485
+ 1CL + 1PLA +22.749
1PLB + 1.1TLA-1.01
+ 1.1TLB
-6.797
+ 1.1BTA +0.846
1.1BTB -63.718
Max My 27291 1004 1DL26236
+ 1SIDL 1880.876
+ 1CL + 1PLB +-3.274
1.1TLB - 1.1BTB
2.052 4.998 53.602 39.882
Min My 27299 1004 1DL26225
+ 1SIDL 1880.876
+ 1CL + 1PLB -35.057
+ 1.1TLB - 1.1BTB
41.374 4.998 -231.596 -219.882
Max Mz 27291 1006 1DL26236
+ 1SIDL 1998.458
+ 1CL + 1PLA +-0.302
1PLB + 1.1TLA
3.395
+ 1.1TLB6.804
- 1.1BTA -42.215
1.1BTB 85.306
Min Mz 27299 1006 1DL26225
+ 1SIDL 1998.458
+ 1CL + 1PLA -58.595
+ 1PLB + 1.1TLA
36.937
+ 1.1TLB6.804
- 1.1BTA-230.838
- 1.1BTB -287.877

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 27261 1095 1DL26205
+ 1SIDL 5426.511
+ 0.3CL + 0.3PLA
174.508
+ 0.3PLB548.037
+ 0.33TLA 76.815
+ 0.33TLB1160.612
+ 0.33BTA + 434.981
0.33BTB + 0.3SLX + 0.
Min Fx 27282 1079 1DL26227
+ 1SIDL-1962.769
+ 0.3CL + 0.3PLA
-343.655
+ 0.3PLB
-227.146
+ 0.33TLA-77.452
+ 0.33TLB-521.185
+ 0.33BTA +-246.781
0.33BTB + 1SLX + 0.3S
Max Fy 27299 1079 1DL26225
+ 1SIDL 4824.314
+ 0.3CL + 0.3PLA
557.978
+ 0.3PLB350.264
+ 0.33TLA 76.858
+ 0.33TLB1554.877
+ 0.33BTA +1889.362
0.33BTB + 1SLX + 0.3S
Min Fy 27299 1086 1DL26225
+ 1SIDL-1768.753
+ 0.3CL + 0.3PLA
-569.639
+ 0.3PLB
-318.209
+ 0.33TLA-73.942
+ 0.33TLB-1760.885
- 0.33BTA -2098.562
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 27278 2078 1DL26223
+ 1SIDL 5330.149
+ 0.3CL + 0.3PLB
236.016
+ 0.33TLB
844.269
- 0.33BTB
80.018
- 0.3SLX
2437.785
- 0.3SLY - 1SLZ
812.336
- 1.1LLB
Min Fz 27278 3047 1DL26223
+ 1SIDL +-819.097
0.3CL + 0.3PLA
-245.202
+ 0.33TLA
-821.933
+ 0.33BTA
-79.889
+ 0.3SLX
-2559.912
+ 0.3SLY-987.622
+ 1SLZ + 1.1NLA
Max Mx 27282 1102 1DL26227
+ 1SIDL 4533.577
+ 0.3CL + 0.3PLA
193.247
+ 0.3PLB532.121
+ 0.33TLA 82.452
+ 0.33TLB -526.719
0.33BTA - 0.33BTB
365.526- 0.3SLX - 0.3S
Min Mx 27261 1079 1DL26206
+ 1SIDL + -65.685
0.3CL + 0.3PLA
-307.919
+ 0.3PLB
-258.371
+ 0.33TLA-81.177
+ 0.33TLB-574.179
+ 0.33BTA +-203.409
0.33BTB + 1SLX + 0.3S
Max My 27278 3047 1DL26204
+ 1SIDL 5383.687
+ 0.3CL + 0.3PLA
253.621
+ 0.33TLA
823.319
+ 0.33BTA
77.204
+ 0.3SLX
3339.622
+ 0.3SLY1112.657
+ 1SLZ + 1.1NLA
Min My 27278 2078 1DL26204
+ 1SIDL +-872.634
0.3CL + 0.3PLB
-262.807
+ 0.33TLB
-800.984
- 0.33BTB
-77.075
- 0.3SLX
-3484.173
- 0.3SLY -1297.165
- 1SLZ - 1.1LLB
Max Mz 27299 1079 1DL26225
+ 1SIDL 4824.314
+ 0.3CL + 0.3PLA
557.978
+ 0.3PLB350.264
+ 0.33TLA 76.858
+ 0.33TLB1554.877
+ 0.33BTA +1889.362
0.33BTB + 1SLX + 0.3S
Min Mz 27299 1086 1DL26225
+ 1SIDL-1768.753
+ 0.3CL + 0.3PLA
-569.639
+ 0.3PLB
-318.209
+ 0.33TLA-73.942
+ 0.33TLB-1760.885
- 0.33BTA -2098.562
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 27282 2104 1.15DL
26226
+ 1.2SIDL
7593.167
+ 1.4CL564.572
+ 1.4PLB + 203.955
1.54TLB - 118.622
1.54BTB 691.078 524.219
Min Fx 27282 2103 1.15DL
26227
+ 1.2SIDL
-3569.699
+ 1.4CL-587.211
+ 1.4PLB + -155.284
1.54TLB +-115.551
1.54BTB -708.405 -187.315
Max Fy 27299 2103 1.15DL
26225
+ 1.2SIDL
7140.688
+ 1.4CL
1000.787
+ 1.4PLB + 239.809
1.54TLB + 110.202
1.54BTB 1304.427 3162.654
Min Fy 27299 2104 1.15DL
26244
+ 1.2SIDL
-3117.22
+ 1.4CL-1016.66
+ 1.4PLB + -175.186
1.54TLB --107.131
1.54BTB -1425.057 -2438.456
Max Fz 27278 2378 1.15DL
26223
+ 1.2SIDL
6479.458
+ 0.42CL295.794
+ 0.42PLB1060.419
+ 0.462TLB100.557
- 0.462BTB
3060.96
- 0.3SLX1025.234
- 0.3SLY - 1SLZ - 1.54
Min Fz 27278 3147 1.15DL
26223
+ 1.2SIDL
-1233.866
+ 0.42CL
-306.142
+ 0.42PLA
-1034.695
+ 0.462TLA
-100.592
+ 0.462BTA
-3203.031
+ 0.3SLX
-1228.556
+ 0.3SLY + 1SLZ + 1.5
Max Mx 27261 2104 1.15DL
26205
+ 1.2SIDL
6022.104
+ 1.4CL516.682
+ 1.4PLB + 245.291
1.54TLB - 1.54BTB
122.16 848.258 379.013
Min Mx 27261 2103 1.15DL
26206
+ 1.2SIDL
91.987
+ 1.4CL-537.648
+ 1.4PLB + -203.241
1.54TLB +-123.018
1.54BTB -792.366 -163.43
Max My 27278 3147 1.15DL
26204
+ 1.2SIDL
6554.41
+ 0.42CL320.441
+ 0.42PLA1031.089
+ 0.462TLA96.618
+ 0.462BTA
4207.101
+ 0.3SLX1410.929
+ 0.3SLY + 1SLZ + 1.5
Min My 27278 2378 1.15DL
26204
+ 1.2SIDL
-1308.818
+ 0.42CL
-330.789
+ 0.42PLB
-1005.365
+ 0.462TLB -96.653
- 0.462BTB
-4374.999
- 0.3SLX-1624.64
- 0.3SLY - 1SLZ - 1.54
Max Mz 27299 2103 1.15DL
26225
+ 1.2SIDL
7140.688
+ 1.4CL
1000.787
+ 1.4PLB + 239.809
1.54TLB + 110.202
1.54BTB 1304.427 3162.654
Min Mz 27299 2186 1.15DL
26225
+ 1.2SIDL
-2355.477
+ 0.42CL
-717.364
+ 0.42PLA-400.044
+ 0.42PLB +-92.827
0.462TLA-2207.885
+ 0.462TLB-2633.984
- 0.462BTA - 0.462BTB

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 2760.485 1351.739 9575.000 OK
ODE Seismic 5426.511 -1962.769 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 40 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -1309 4667 5512 0.847 OK
Minima 7593 867.4 6633 0.131 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 142.8 OK
Minima -327.4 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 3.173 OK 19.92 OK
Minima -0.2727 OK 0.7988 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.001 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 20.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28430 1005 1DL26222
+ 1SIDL 2760.485
+ 1CL + 1PLA +-8.037
1PLB + 1.1TLA
0.262
+ 1.1TLB
-6.797
+ 1.1BTA +-0.913
1.1BTB -22.61
Min Fx 28431 1005 1DL26243
+ 1SIDL 1351.739
+ 1CL + 1PLA +-8.568
1PLB + 1.1TLA
-0.627
+ 1.1TLB
-4.895
+ 1.1BTA +3.343
1.1BTB -24.529
Max Fy 28431 1006 1DL26243
+ 1SIDL 1998.458
+ 1CL + 1PLA + 8.218
1PLB + 1.1TLA
-4.713
+ 1.1TLB6.804
- 1.1BTA -23.191
1.1BTB 34.815
Min Fy 28431 1005 1DL26243
+ 1SIDL 1351.739
+ 1CL + 1PLA +-8.568
1PLB + 1.1TLA
-0.627
+ 1.1TLB
-4.895
+ 1.1BTA +3.343
1.1BTB -24.529
Max Fz 28430 1001 1DL26222
+ 1SIDL 2569.151
+ 1CL + 1PLA +-4.495
1.1TLA + 1.1BTA
1.598 -4.008 -5.492 -10.992
Min Fz 28431 1004 1DL26243
+ 1SIDL 1880.876
+ 1CL + 1PLB + 4.466
1.1TLB - 1.1BTB
-5.534 4.998 25.297 22.031
Max Mx 28431 1006 1DL26243
+ 1SIDL 1998.458
+ 1CL + 1PLA + 8.218
1PLB + 1.1TLA
-4.713
+ 1.1TLB6.804
- 1.1BTA -23.191
1.1BTB 34.815
Min Mx 28430 1005 1DL26222
+ 1SIDL 2760.485
+ 1CL + 1PLA +-8.037
1PLB + 1.1TLA
0.262
+ 1.1TLB
-6.797
+ 1.1BTA +-0.913
1.1BTB -22.61
Max My 28431 1004 1DL26243
+ 1SIDL 1880.876
+ 1CL + 1PLB + 4.466
1.1TLB - 1.1BTB
-5.534 4.998 25.297 22.031
Min My 28430 1001 1DL26222
+ 1SIDL 2569.151
+ 1CL + 1PLA +-4.495
1.1TLA + 1.1BTA
1.598 -4.008 -5.492 -10.992
Max Mz 28431 1006 1DL26243
+ 1SIDL 1998.458
+ 1CL + 1PLA + 8.218
1PLB + 1.1TLA
-4.713
+ 1.1TLB6.804
- 1.1BTA -23.191
1.1BTB 34.815
Min Mz 28431 1005 1DL26243
+ 1SIDL 1351.739
+ 1CL + 1PLA +-8.568
1PLB + 1.1TLA
-0.627
+ 1.1TLB
-4.895
+ 1.1BTA +3.343
1.1BTB -24.529
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28430 1095 1DL26222
+ 1SIDL 5426.511
+ 0.3CL + 0.3PLA33.13
+ 0.3PLB120.899
+ 0.33TLA 76.815
+ 0.33TLB +476.239
0.33BTA + 143.304
0.33BTB + 0.3SLX + 0.
Min Fx 28431 1079 1DL28025
+ 1SIDL-1962.769
+ 0.3CL + 0.3PLA
-86.32
+ 0.3PLB-49.421
+ 0.33TLA-77.452
+ 0.33TLB-146.682
+ 0.33BTA +-223.739
0.33BTB + 1SLX + 0.3S
Max Fy 28431 1086 1DL28025
+ 1SIDL +5018.33
0.3CL + 0.3PLA
86.518
+ 0.3PLB45.384
+ 0.33TLA 80.367
+ 0.33TLB -162.915
0.33BTA - 0.33BTB
234.298- 1SLX - 0.3SLY
Min Fy 28431 1079 1DL28025
+ 1SIDL-1962.769
+ 0.3CL + 0.3PLA
-86.32
+ 0.3PLB-49.421
+ 0.33TLA-77.452
+ 0.33TLB-146.682
+ 0.33BTA +-223.739
0.33BTB + 1SLX + 0.3S
Max Fz 28430 3047 1DL26222
+ 1SIDL 5383.687
+ 0.3CL + 0.3PLA
34.119
+ 0.33TLA
121.905
+ 0.33BTA
77.204
+ 0.3SLX
472.559
+ 0.3SLY 146.416
+ 1SLZ + 1.1NLA
Min Fz 28430 2078 1DL26222
+ 1SIDL +-872.634
0.3CL + 0.3PLB
-34.149
+ 0.33TLB
-124.708
- 0.33BTB
-77.075
- 0.3SLX
-458.411
- 0.3SLY - -137.446
1SLZ - 1.1LLB
Max Mx 28431 1102 1DL28025
+ 1SIDL 4533.577
+ 0.3CL + 0.3PLA
45.167
+ 0.3PLB114.037
+ 0.33TLA 82.452
+ 0.33TLB -343.261
0.33BTA - 0.33BTB
148.104- 0.3SLX - 0.3S
Min Mx 28430 1079 1DL28016
+ 1SIDL + -65.685
0.3CL + 0.3PLA
-79.348
+ 0.3PLB-54.246
+ 0.33TLA-81.177
+ 0.33TLB-166.864
+ 0.33BTA +-200.875
0.33BTB + 1SLX + 0.3S
Max My 28430 3071 1DL26222
+ 1SIDL 5372.947
+ 0.3CL + 0.3PLB
34.475
+ 0.33TLB
119.309
+ 0.33BTB
78.459
+ 0.3SLX482.67
+ 0.3SLY +148.235
1SLZ + 1.1NLB
Min My 28430 1054 1DL26222
+ 1SIDL +-890.252
0.3CL + 0.3PLA
-34.416
+ 0.33TLA
-123.114
- 0.33BTA
-77.653
- 0.3SLX
-464.726
- 0.3SLY --138.762
1SLZ
Max Mz 28431 1007 1DL26243
+ 1SIDL 4858.187
+ 1SLX + 0.3SLY84.117
+ 0.3SLZ 46.277 78.828 209.124 312.012
Min Mz 28431 1014 1DL26243
+ 1SIDL-1928.897
- 1SLX - 0.3SLY
-83.684
- 0.3SLZ -49.754 -75.481 -191.54 -301.053

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28431 2104 1.15DL
26243
+ 1.2SIDL
7593.167
+ 1.4CL157.118
+ 1.4PLB + 1.54TLB
21.857 - 118.622
1.54BTB 164.799 565.354
Min Fx 28431 2103 1.15DL
28025
+ 1.2SIDL
-3569.699
+ 1.4CL-156.959
+ 1.4PLB + 1.54TLB
-30.333 +-115.551
1.54BTB -100.537 -393.464
Max Fy 28431 2104 1.15DL
26243
+ 1.2SIDL
7593.167
+ 1.4CL157.118
+ 1.4PLB + 1.54TLB
21.857 - 118.622
1.54BTB 164.799 565.354
Min Fy 28431 2103 1.15DL
28025
+ 1.2SIDL
-3569.699
+ 1.4CL-156.959
+ 1.4PLB + 1.54TLB
-30.333 +-115.551
1.54BTB -100.537 -393.464
Max Fz 28430 3147 1.15DL
26222
+ 1.2SIDL
6554.41
+ 0.42CL42.641
+ 0.42PLA 153.432
+ 0.462TLA96.618
+ 0.462BTA591.74
+ 0.3SLX182.691
+ 0.3SLY + 1SLZ + 1.5
Min Fz 28430 2378 1.15DL
26222
+ 1.2SIDL
-1308.818
+ 0.42CL-42.731
+ 0.42PLB-156.647
+ 0.462TLB -96.653
- 0.462BTB
-575.409
- 0.3SLX-172.438
- 0.3SLY - 1SLZ - 1.54
Max Mx 28430 2104 1.15DL
26222
+ 1.2SIDL
6022.104
+ 1.4CL +146.58
1.4PLB + 1.54TLB
30.081 - 1.54BTB
122.16 199.513 520.292
Min Mx 28430 2103 1.15DL
28016
+ 1.2SIDL
91.987
+ 1.4CL-146.495
+ 1.4PLB + 1.54TLB
-37.579 +-123.018
1.54BTB -131.534 -360.03
Max My 28430 3171 1.15DL
26222
+ 1.2SIDL
6539.374
+ 0.42CL +43.14
0.42PLB 149.798
+ 0.462TLB 98.376
+ 0.462BTB
605.895
+ 0.3SLX185.238
+ 0.3SLY + 1SLZ + 1.
Min My 28430 2154 1.15DL
26222
+ 1.2SIDL
-1333.483
+ 0.42CL-43.104
+ 0.42PLA-154.416
+ 0.462TLA-97.462
- 0.462BTA
-584.251
- 0.3SLX --174.28
0.3SLY - 1SLZ
Max Mz 28431 2104 1.15DL
26243
+ 1.2SIDL
7593.167
+ 1.4CL157.118
+ 1.4PLB + 1.54TLB
21.857 - 118.622
1.54BTB 164.799 565.354
Min Mz 28431 2103 1.15DL
28025
+ 1.2SIDL
-3569.699
+ 1.4CL-156.959
+ 1.4PLB + 1.54TLB
-30.333 +-115.551
1.54BTB -100.537 -393.464

ODE MDE
Maximum Tension Force (kN) -1962.77 -3569.7
Skin Friction (kN) 2904.67
Final Axial Load (kN) 0.00 -665.03

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -665 406.1 574.5 0.707 OK
Minima 7593 588.9 2901 0.203 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 49.61 OK
Minima -156.2 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 2.512 OK 17.75 OK
Minima 1.025 OK 7.527 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.954 m
Hence de = 0.904 m and dv = 0.813 m
Horizontal resultant shear force at the section, Vu = 1101 kN
Corresponding axial compressive force, N = 6479 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 40212 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0201 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 2.060 %
Horizontal shear force, Vu = 1101 kN
Shear stress (vv = Vu /(bv . dv) = 1128.02 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.940 Mpa
= 940 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 832.311 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.29
Modified shear strength of concrete (n s vc ) = 1070.73 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 55.91 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.38 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 12.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 27270 1005 1DL26214
+ 1SIDL 2760.485
+ 1CL + 1PLA -11.142
+ 1PLB + 1.1TLA
0.188
+ 1.1TLB
-6.797
+ 1.1BTA +-3.321
1.1BTB -118.399
Min Fx 27291 1005 1DL26235
+ 1SIDL 1351.739
+ 1CL + 1PLA -11.451
+ 1PLB + 1.1TLA0.71
+ 1.1TLB
-4.895
+ 1.1BTA +4.363
1.1BTB -124.901
Max Fy 27297 1006 1DL26241
+ 1SIDL 1998.458
+ 1CL + 1PLA + 9.031
1PLB + 1.1TLA
-4.618
+ 1.1TLB6.804
- 1.1BTA -32.596
1.1BTB 52.61
Min Fy 27294 1005 1DL26238
+ 1SIDL 1351.739
+ 1CL + 1PLA -14.023
+ 1PLB + 1.1TLA
-0.158
+ 1.1TLB
-4.895
+ 1.1BTA +5.466
1.1BTB -86.492
Max Fz 27291 1006 1DL26235
+ 1SIDL 1998.458
+ 1CL + 1PLA +-0.302
1PLB + 1.1TLA
3.395
+ 1.1TLB6.804
- 1.1BTA - 1.1BTB
38.82 85.004
Min Fz 27298 1004 1DL26242
+ 1SIDL 1880.876
+ 1CL + 1PLB + 4.531
1.1TLB - 1.1BTB
-5.765 4.998 31.062 26.562
Max Mx 27291 1006 1DL26235
+ 1SIDL 1998.458
+ 1CL + 1PLA +-0.302
1PLB + 1.1TLA
3.395
+ 1.1TLB6.804
- 1.1BTA - 1.1BTB
38.82 85.004
Min Mx 27270 1005 1DL26214
+ 1SIDL 2760.485
+ 1CL + 1PLA -11.142
+ 1PLB + 1.1TLA
0.188
+ 1.1TLB
-6.797
+ 1.1BTA +-3.321
1.1BTB -118.399
Max My 27291 1004 1DL26236
+ 1SIDL 1880.876
+ 1CL + 1PLB +-3.274
1.1TLB - 1.1BTB
2.052 4.998 53.602 39.882
Min My 27270 1001 1DL26214
+ 1SIDL 2569.151
+ 1CL + 1PLA +-7.884
1.1TLA + 1.1BTA
1.217 -4.008 -20.459 -71.311
Max Mz 27291 1006 1DL26236
+ 1SIDL 1998.458
+ 1CL + 1PLA +-0.302
1PLB + 1.1TLA
3.395
+ 1.1TLB6.804
- 1.1BTA -42.215
1.1BTB 85.306
Min Mz 27291 1005 1DL26235
+ 1SIDL 1351.739
+ 1CL + 1PLA -11.451
+ 1PLB + 1.1TLA0.71
+ 1.1TLB
-4.895
+ 1.1BTA +4.363
1.1BTB -124.901

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 27270 1095 1DL26214
+ 1SIDL 5426.511
+ 0.3CL + 0.3PLA22.07
+ 0.3PLB49.015
+ 0.33TLA 76.815
+ 0.33TLB1404.943
+ 0.33BTA + 333.787
0.33BTB + 0.3SLX + 0.
Min Fx 27291 1079 1DL26236
+ 1SIDL-1962.769
+ 0.3CL + 0.3PLA
-61.816
+ 0.3PLB -26.12
+ 0.33TLA-77.452
+ 0.33TLB-494.977
+ 0.33BTA-1011.982
+ 0.33BTB + 1SLX + 0.3S
Max Fy 27296 1086 1DL26241
+ 1SIDL +5018.33
0.3CL + 0.3PLA
106.906
+ 0.3PLB50.844
+ 0.33TLA 80.367
+ 0.33TLB -323.231
0.33BTA - 0.33BTB
519.519- 1SLX - 0.3SLY
Min Fy 27295 1079 1DL26240
+ 1SIDL-1962.769
+ 0.3CL + 0.3PLA
-109.982
+ 0.3PLB-50.418
+ 0.33TLA-77.452
+ 0.33TLB-346.573
+ 0.33BTA +-620.428
0.33BTB + 1SLX + 0.3S
Max Fz 27275 3047 1DL26219
+ 1SIDL 5383.687
+ 0.3CL + 0.3PLA
36.263
+ 0.33TLA
145.135
+ 0.33BTA
77.204
+ 0.3SLX
890.936
+ 0.3SLY 256.078
+ 1SLZ + 1.1NLA
Min Fz 27275 2078 1DL26219
+ 1SIDL +-872.634
0.3CL + 0.3PLB
-38.997
+ 0.33TLB
-147.484
- 0.33BTB
-77.075
- 0.3SLX
-868.934
- 0.3SLY - -252.169
1SLZ - 1.1LLB
Max Mx 27291 1102 1DL26236
+ 1SIDL 4533.577
+ 0.3CL + 0.3PLA
27.365
+ 0.3PLB50.516
+ 0.33TLA 82.452
+ 0.33TLB1328.422
- 0.33BTA - 0.33BTB
464.964- 0.3SLX - 0.3S
Min Mx 27270 1079 1DL26215
+ 1SIDL + -65.685
0.3CL + 0.3PLA
-60.947
+ 0.3PLB-26.907
+ 0.33TLA-81.177
+ 0.33TLB-551.291
+ 0.33BTA +-940.245
0.33BTB + 1SLX + 0.3S
Max My 27270 3071 1DL26214
+ 1SIDL 5372.947
+ 0.3CL + 0.3PLB
22.789
+ 0.33TLB48.767
+ 0.33BTB
78.459
+ 0.3SLX
1422.335
+ 0.3SLY +350.072
1SLZ + 1.1NLB
Min My 27270 1054 1DL26214
+ 1SIDL +-890.252
0.3CL + 0.3PLA
-32.008
+ 0.33TLA
-46.806
- 0.33BTA
-77.653
- 0.3SLX
-1388.59
- 0.3SLY --377.868
1SLZ
Max Mz 27291 1007 1DL26235
+ 1SIDL 4858.187
+ 1SLX + 0.3SLY50.614
+ 0.3SLZ 28.864 78.828 524.101 1006.907
Min Mz 27291 1014 1DL26235
+ 1SIDL-1928.897
- 1SLX - 0.3SLY
-59.751
- 0.3SLZ -25.887 -75.481 -496.908 -1030.548
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 27291 2104 1.15DL
26235
+ 1.2SIDL
7593.167
+ 1.4CL +94.534
1.4PLB + 1.54TLB
30.38 - 118.622
1.54BTB 272.834 1934.387
Min Fx 27291 2103 1.15DL
26236
+ 1.2SIDL
-3569.699
+ 1.4CL-108.795
+ 1.4PLB + 1.54TLB
-26.026 +-115.551
1.54BTB -215.324 -1867.923
Max Fy 27295 2104 1.15DL
26239
+ 1.2SIDL
7593.167
+ 1.4CL199.723
+ 1.4PLB + 1.54TLB
14.764 - 118.622
1.54BTB 279.52 1329.47
Min Fy 27295 2103 1.15DL
26240
+ 1.2SIDL
-3569.699
+ 1.4CL-205.984
+ 1.4PLB + 1.54TLB
-21.284 +-115.551
1.54BTB -192.728 -1122.079
Max Fz 27275 3147 1.15DL
26219
+ 1.2SIDL
6554.41
+ 0.42CL45.409
+ 0.42PLA 182.614
+ 0.462TLA96.618
+ 0.462BTA
1115.89
+ 0.3SLX319.907
+ 0.3SLY + 1SLZ + 1.5
Min Fz 27275 2378 1.15DL
26219
+ 1.2SIDL
-1308.818
+ 0.42CL-48.663
+ 0.42PLB-185.278
+ 0.462TLB -96.653
- 0.462BTB
-1090.607
- 0.3SLX-315.745
- 0.3SLY - 1SLZ - 1.54
Max Mx 27270 2104 1.15DL
26214
+ 1.2SIDL
6022.104
+ 1.4CL +95.337
1.4PLB + 1.54TLB
30.556 - 1.54BTB
122.16 347.141 1826.669
Min Mx 27270 2103 1.15DL
26215
+ 1.2SIDL
91.987
+ 1.4CL-108.743
+ 1.4PLB + 1.54TLB
-27.359 +-123.018
1.54BTB -300.86 -1758.385
Max My 27270 3171 1.15DL
26214
+ 1.2SIDL
6539.374
+ 0.42CL28.879
+ 0.42PLB +61.059
0.462TLB98.376
+ 0.462BTB
1786.509
+ 0.3SLX438.843
+ 0.3SLY + 1SLZ + 1.
Min My 27270 2154 1.15DL
26214
+ 1.2SIDL
-1333.483
+ 0.42CL-39.678
+ 0.42PLA +-58.811
0.462TLA-97.462
- 0.462BTA
-1745.146
- 0.3SLX-471.754
- 0.3SLY - 1SLZ
Max Mz 27291 2104 1.15DL
26235
+ 1.2SIDL
7593.167
+ 1.4CL +94.534
1.4PLB + 1.54TLB
30.38 - 118.622
1.54BTB 272.834 1934.387
Min Mz 27291 2103 1.15DL
26236
+ 1.2SIDL
-3569.699
+ 1.4CL-108.795
+ 1.4PLB + 1.54TLB
-26.026 +-115.551
1.54BTB -215.324 -1867.923

ODE MDE
Maximum Tension Force (kN) -1962.77 -3569.7
Skin Friction (kN) 1110.67
Final Axial Load (kN) -852.10 -2459.03

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


40 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -2459 1880 2380 0.790 OK
Minima 6554 1161 4457 0.260 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 75.15 OK
Minima -197.9 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 2.819 OK 19.15 OK
Minima 0.4255 OK 4.079 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP PG2A


Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

PILE DESIGN FOR GROUP PG2A

Grade of Concrete = C40


Grade of Reinforcement = Fe390
No. of Piles = 2
Pile Diameter = 1.2 m
Pile Length = 47 m
Vertical Pile Capacity
Static Case = 9575 kN
Seismic Case (ODE) = 13639 kN

1.0 Member Forces from STAAD at Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31670 1005 1DL30730
+ 1SIDL 2506.631
+ 1CL + 1PLA +15.391
1PLB + 1.1TLA
-1.561
+ 1.1TLB
-29.468
+ 1.1BTA-52.813
+ 1.1BTB -75.2
Min Fx 31639 1003 1DL30699
+ 1SIDL 1633.393
+ 1CL + 1PLB +-4.297
1.1TLB + 1.1BTB
4.028 -21.018 -32.459 -92.894
Max Fy 31687 1005 1DL30729
+ 1SIDL 2506.631
+ 1CL + 1PLA +33.881
1PLB + 1.1TLA
-7.81
+ 1.1TLB
-29.468
+ 1.1BTA-36.316
+ 1.1BTB 6.384
Min Fy 31687 1006 1DL30729
+ 1SIDL 1932.586
+ 1CL + 1PLA -76.807
+ 1PLB + 1.1TLA
-33.995
+ 1.1TLB
-1.708
- 1.1BTA160.477
- 1.1BTB -350.594
Max Fz 31639 1005 1DL30699
+ 1SIDL 1642.353
+ 1CL + 1PLA + 3.111
1PLB + 1.1TLA
8.055
+ 1.1TLB
-25.833
+ 1.1BTA-69.573
+ 1.1BTB -113.034
Min Fz 31656 1006 1DL30698
+ 1SIDL 2240.985
+ 1CL + 1PLA -75.951
+ 1PLB + 1.1TLA
-38.025
+ 1.1TLB6.228
- 1.1BTA194.549
- 1.1BTB -341.23
Max Mx 31639 1006 1DL30699
+ 1SIDL 2240.985
+ 1CL + 1PLA -51.695
+ 1PLB + 1.1TLA
-27.128
+ 1.1TLB6.228
- 1.1BTA -91.533
1.1BTB -138.362
Min Mx 31670 1005 1DL30730
+ 1SIDL 2506.631
+ 1CL + 1PLA +15.391
1PLB + 1.1TLA
-1.561
+ 1.1TLB
-29.468
+ 1.1BTA-52.813
+ 1.1BTB -75.2
Max My 31656 1006 1DL30698
+ 1SIDL 2240.985
+ 1CL + 1PLA -75.951
+ 1PLB + 1.1TLA
-38.025
+ 1.1TLB6.228
- 1.1BTA194.549
- 1.1BTB -341.23
Min My 31656 1005 1DL30698
+ 1SIDL 1642.353
+ 1CL + 1PLA + 16.32
1PLB + 1.1TLA
7.186
+ 1.1TLB
-25.833
+ 1.1BTA-92.445
+ 1.1BTB -78.736
Max Mz 31647 1006 1DL30708
+ 1SIDL 2240.985
+ 1CL + 1PLA +-4.058
1PLB + 1.1TLA
-3.714
+ 1.1TLB6.228
- 1.1BTA -52.852
- 1.1BTB 119.731
Min Mz 31687 1006 1DL30729
+ 1SIDL 1932.586
+ 1CL + 1PLA -76.807
+ 1PLB + 1.1TLA
-33.995
+ 1.1TLB
-1.708
- 1.1BTA160.477
- 1.1BTB -350.594

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31639 1102 1DL30700
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
150.777
+ 0.3PLB286.185
+ 0.33TLA206.587
+ 0.33TLB -478.114
0.33BTA - 0.33BTB
421.431- 0.3SLX - 0.3S
Min Fx 31639 3071 1DL30700
+ 1SIDL-2276.594
+ 0.3CL + 0.3PLB
-187.947
+ 0.33TLB
-304.782
+ 0.33BTB
-224.775
+ 0.3SLX
-450.729
+ 0.3SLY-563.621
+ 1SLZ + 1.1NLB
Max Fy 31687 1079 1DL30729
+ 1SIDL 5029.075
+ 0.3CL + 0.3PLA
547.181
+ 0.3PLB183.914
+ 0.33TLA140.865
+ 0.33TLB1079.276
+ 0.33BTA +1892.461
0.33BTB + 1SLX + 0.3S
Min Fy 31687 1086 1DL30729
+ 1SIDL +-979.063
0.3CL + 0.3PLA
-575.28
+ 0.3PLB
-224.018
+ 0.33TLA
-168.917
+ 0.33TLB-945.497
- 0.33BTA -2130.797
- 0.33BTB - 1SLX - 0.3SLY
Max Fz 31656 3071 1DL30698
+ 1SIDL 5655.854
+ 0.3CL + 0.3PLB
238.217
+ 0.33TLB
493.182
+ 0.33BTB
197.095
+ 0.3SLX
1535.015
+ 0.3SLY1148.206
+ 1SLZ + 1.1NLB
Min Fz 31656 1102 1DL30698
+ 1SIDL-2063.105
+ 0.3CL + 0.3PLA
-285.093
+ 0.3PLB
-520.872
+ 0.33TLA
-215.283
+ 0.33TLB-1415.364
- 0.33BTA -1458.891
- 0.33BTB - 0.3SLX - 0.3S
Max Mx 31639 1102 1DL30700
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
150.777
+ 0.3PLB286.185
+ 0.33TLA206.587
+ 0.33TLB -478.114
0.33BTA - 0.33BTB
421.431- 0.3SLX - 0.3S
Min Mx 31639 1095 1DL30700
+ 1SIDL-2242.695
+ 0.3CL + 0.3PLA
-186.937
+ 0.3PLB
-305.829
+ 0.33TLA
-224.901
+ 0.33TLB-462.268
+ 0.33BTA +-575.351
0.33BTB + 0.3SLX + 0.
Max My 31656 1007 1DL30698
+ 1SIDL 5073.292
+ 1SLX + 0.3SLY
421.825
+ 0.3SLZ 288.837 171.76 1596.135 1289.154
Min My 31656 1014 1DL30698
+ 1SIDL-1556.653
- 1SLX - 0.3SLY
-459.26
- 0.3SLZ -319.213 -189.52 -1474.626 -1559.168
Max Mz 31687 3055 1DL30729
+ 1SIDL 4971.456
+ 0.3CL + 0.3PLB
544.493
+ 0.33TLB
186.796
+ 0.33BTB
141.105
+ 1SLX
1083.156
+ 0.3SLY +1897.962
0.3SLZ + 1.1NLB
Min Mz 31687 1086 1DL30729
+ 1SIDL +-979.063
0.3CL + 0.3PLA
-575.28
+ 0.3PLB
-224.018
+ 0.33TLA
-168.917
+ 0.33TLB-945.497
- 0.33BTA -2130.797
- 0.33BTB - 1SLX - 0.3SLY
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31639 2202 1.15DL
30700
+ 1.2SIDL
7203.169
+ 0.42CL189.078
+ 0.42PLA 359.187
+ 0.42PLB 260.732
+ 0.462TLA +599.967
0.462TLB - 534.141
0.462BTA - 0.462BTB
Min Fx 31639 3171 1.15DL
30700
+ 1.2SIDL
-3052.583
+ 0.42CL
-233.399
+ 0.42PLB-380.288
+ 0.462TLB-281.718
+ 0.462BTB
-566.843
+ 0.3SLX-699.905
+ 0.3SLY + 1SLZ + 1.
Max Fy 31687 2103 1.15DL
30729
+ 1.2SIDL
7047.014
+ 1.4CL930.284
+ 1.4PLB + 163.974
1.54TLB + 181.77
1.54BTB 1532.041 2854.099
Min Fy 31687 2104 1.15DL
30748
+ 1.2SIDL
-2137.199
+ 1.4CL-961.426
+ 1.4PLB + -201.997
1.54TLB --222.038
1.54BTB -1282.168 -2188.647
Max Fz 31656 3171 1.15DL
30698
+ 1.2SIDL
6904.285
+ 0.42CL301.838
+ 0.42PLB 621.632
+ 0.462TLB 247.443
+ 0.462BTB
1911.38
+ 0.3SLX
1456.443
+ 0.3SLY + 1SLZ + 1.
Min Fz 31656 2202 1.15DL
30698
+ 1.2SIDL
-2753.698
+ 0.42CL -358.1
+ 0.42PLA +-652.85
0.42PLB-268.429
+ 0.462TLA-1773.941
+ 0.462TLB-1823.808
- 0.462BTA - 0.462BTB
Max Mx 31639 2202 1.15DL
30700
+ 1.2SIDL
7203.169
+ 0.42CL189.078
+ 0.42PLA 359.187
+ 0.42PLB 260.732
+ 0.462TLA +599.967
0.462TLB - 534.141
0.462BTA - 0.462BTB
Min Mx 31639 2195 1.15DL
30700
+ 1.2SIDL
-3005.124
+ 0.42CL
-231.985
+ 0.42PLA-381.754
+ 0.42PLB-281.894
+ 0.462TLA -582.996
+ 0.462TLB +-716.327
0.462BTA + 0.462BTB
Max My 31656 2104 1.15DL
30698
+ 1.2SIDL
6784.861
+ 1.4CL709.132
+ 1.4PLB + 291.507
1.54TLB - 241.418
1.54BTB 2362.321 1869.394
Min My 31656 2103 1.15DL
30717
+ 1.2SIDL
-2574.404
+ 1.4CL-763.685
+ 1.4PLB + 1.54TLB
-313.2 +-270.137
1.54BTB -1980.162 -1514.897
Max Mz 31687 2103 1.15DL
30729
+ 1.2SIDL
7047.014
+ 1.4CL930.284
+ 1.4PLB + 163.974
1.54TLB + 181.77
1.54BTB 1532.041 2854.099
Min Mz 31687 2186 1.15DL
30729
+ 1.2SIDL
-1436.005
+ 0.42CL
-724.017
+ 0.42PLA + -279.2
0.42PLB-210.035
+ 0.462TLA-1186.804
+ 0.462TLB-2674.683
- 0.462BTA - 0.462BTB

1.1 Check for Pile Capacity (SLS)

Max. Vertical Min. Vertical Load


Case Pile Capacity (kN)
Load (kN) (kN)
Static 2506.631 1633.393 9575.000 OK
ODE Seismic 5869.343 -2276.594 13639.000 OK

1.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

1.2.1 Minimum Reinforcement Required

From Table 9.6N, pg. 168, EN 1992-1-1: 2004 (E), recommended minimum longitudinal reinforcement area
As,bpmin varies according to pile cross-sectional area, Ac .
Here, Ac = 1.131 m2
Therefore, minimum percentage of reinforcement required, As,bpmin = 0.250 %

Reinforcement Provided

Dia. (mm) Nos.


st
1 Layer 32 32 (16 bundles of 2)
2nd Layer 0 0
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

1.2.2 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -1436 2926 3567 0.820 OK
Minima 7203 803.3 5127 0.157 OK

N/M Curve for MDE

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 102.7 OK
Minima -327.6 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 3.717 OK 23.49 OK
Minima -0.443 OK -0.16 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.003 mm OK

2.0 Curtailment Check


2.1 Member Forces from STAAD at 20.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31690 1005 1DL30747
+ 1SIDL 2506.631
+ 1CL + 1PLA +-6.266
1PLB + 1.1TLA
1.802
+ 1.1TLB
-29.468
+ 1.1BTA +-2.758
1.1BTB -16.097
Min Fx 31659 1003 1DL30716
+ 1SIDL 1633.393
+ 1CL + 1PLB +-1.191
1.1TLB + -0.294
1.1BTB -21.018 2.913 1.656
Max Fy 31690 1006 1DL30747
+ 1SIDL 1932.586
+ 1CL + 1PLA +11.025
1PLB + 1.1TLA4.83
+ 1.1TLB
-1.708
- 1.1BTA -20.034
- 1.1BTB 44.962
Min Fy 31690 1005 1DL30747
+ 1SIDL 2506.631
+ 1CL + 1PLA +-6.266
1PLB + 1.1TLA
1.802
+ 1.1TLB
-29.468
+ 1.1BTA +-2.758
1.1BTB -16.097
Max Fz 31659 1006 1DL30716
+ 1SIDL 2240.985
+ 1CL + 1PLA +10.954
1PLB + 1.1TLA5.26
+ 1.1TLB6.228
- 1.1BTA -22.788
- 1.1BTB 44.324
Min Fz 31662 1005 1DL30721
+ 1SIDL 1642.353
+ 1CL + 1PLA +-0.924
1PLB + 1.1TLA
-0.795
+ 1.1TLB
-25.833
+ 1.1BTA +3.909
1.1BTB 3.26
Max Mx 31659 1006 1DL30716
+ 1SIDL 2240.985
+ 1CL + 1PLA +10.954
1PLB + 1.1TLA5.26
+ 1.1TLB6.228
- 1.1BTA -22.788
- 1.1BTB 44.324
Min Mx 31690 1005 1DL30747
+ 1SIDL 2506.631
+ 1CL + 1PLA +-6.266
1PLB + 1.1TLA
1.802
+ 1.1TLB
-29.468
+ 1.1BTA +-2.758
1.1BTB -16.097
Max My 31659 1005 1DL30716
+ 1SIDL 1642.353
+ 1CL + 1PLA +-3.793
1PLB + 1.1TLA
-0.467
+ 1.1TLB
-25.833
+ 1.1BTA + 1.1BTB
5.71 -5.692
Min My 31659 1006 1DL30716
+ 1SIDL 2240.985
+ 1CL + 1PLA +10.954
1PLB + 1.1TLA5.26
+ 1.1TLB6.228
- 1.1BTA -22.788
- 1.1BTB 44.324
Max Mz 31690 1006 1DL30747
+ 1SIDL 1932.586
+ 1CL + 1PLA +11.025
1PLB + 1.1TLA4.83
+ 1.1TLB
-1.708
- 1.1BTA -20.034
- 1.1BTB 44.962
Min Mz 31690 1005 1DL30747
+ 1SIDL 2506.631
+ 1CL + 1PLA +-6.266
1PLB + 1.1TLA
1.802
+ 1.1TLB
-29.468
+ 1.1BTA +-2.758
1.1BTB -16.097
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31659 1102 1DL30719
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
39.447
+ 0.3PLB82.006
+ 0.33TLA206.587
+ 0.33TLB -184.213
0.33BTA - 0.33BTB
131.41- 0.3SLX - 0.3S
Min Fx 31659 3071 1DL30719
+ 1SIDL-2276.594
+ 0.3CL + 0.3PLB
-33.633
+ 0.33TLB
-77.967
+ 0.33BTB
-224.775
+ 0.3SLX
-196.214
+ 0.3SLY-107.345
+ 1SLZ + 1.1NLB
Max Fy 31690 1086 1DL30750
+ 1SIDL 4856.862
+ 0.3CL + 0.3PLA
87.269
+ 0.3PLB31.298
+ 0.33TLA149.193
+ 0.33TLB - 0.33BTA
82.437 - 0.33BTB
237.009- 1SLX - 0.3SLY
Min Fy 31690 1079 1DL30750
+ 1SIDL +-806.849
0.3CL + 0.3PLA
-84.277
+ 0.3PLB-25.075
+ 0.33TLA
-177.245
+ 0.33TLB +-98.449
0.33BTA +-220.777
0.33BTB + 1SLX + 0.3S
Max Fz 31659 1102 1DL30719
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
39.447
+ 0.3PLB82.006
+ 0.33TLA206.587
+ 0.33TLB -184.213
0.33BTA - 0.33BTB
131.41- 0.3SLX - 0.3S
Min Fz 31659 3071 1DL30719
+ 1SIDL-2276.594
+ 0.3CL + 0.3PLB
-33.633
+ 0.33TLB
-77.967
+ 0.33BTB
-224.775
+ 0.3SLX
-196.214
+ 0.3SLY-107.345
+ 1SLZ + 1.1NLB
Max Mx 31659 1102 1DL30719
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
39.447
+ 0.3PLB82.006
+ 0.33TLA206.587
+ 0.33TLB -184.213
0.33BTA - 0.33BTB
131.41- 0.3SLX - 0.3S
Min Mx 31659 1095 1DL30719
+ 1SIDL-2242.695
+ 0.3CL + 0.3PLA
-34.194
+ 0.3PLB-77.402
+ 0.33TLA
-224.901
+ 0.33TLB-196.878
+ 0.33BTA +-107.984
0.33BTB + 0.3SLX + 0.
Max My 31659 3071 1DL30716
+ 1SIDL 5655.854
+ 0.3CL + 0.3PLB
35.583
+ 0.33TLB79.723
+ 0.33BTB
197.095
+ 0.3SLX
269.641
+ 0.3SLY +157.038
1SLZ + 1.1NLB
Min My 31659 1102 1DL30716
+ 1SIDL-2063.105
+ 0.3CL + 0.3PLA
-29.77
+ 0.3PLB-75.684
+ 0.33TLA
-215.283
+ 0.33TLB --285.68
0.33BTA - 0.33BTB
-127.16- 0.3SLX - 0.3S
Max Mz 31690 1007 1DL30747
+ 1SIDL 4859.567
+ 1SLX + 0.3SLY84.297
+ 0.3SLZ 30.756 145.698 109.083 313.048
Min Mz 31690 1014 1DL30747
+ 1SIDL --976.357
1SLX - 0.3SLY
-82.062
- 0.3SLZ -24.708 -172.411 -131.079 -297.957

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31659 2202 1.15DL
30719
+ 1.2SIDL
7203.169
+ 0.42CL +49.63
0.42PLA 102.787
+ 0.42PLB 260.732
+ 0.462TLA +231.201
0.462TLB - 0.462BTA
164.76 - 0.462BTB
Min Fx 31659 3171 1.15DL
30719
+ 1.2SIDL
-3052.583
+ 0.42CL +-42.6
0.42PLB +-98.258
0.462TLB
-281.718
+ 0.462BTB
-244.819
+ 0.3SLX-136.069
+ 0.3SLY + 1SLZ + 1.
Max Fy 31690 2104 1.15DL
30747
+ 1.2SIDL
6654.95
+ 1.4CL149.702
+ 1.4PLB + 1.54TLB
22.364 - 200.886
1.54BTB 104.604 531.664
Min Fy 31690 2103 1.15DL
30750
+ 1.2SIDL
-1745.136
+ 1.4CL -146.72
+ 1.4PLB + 1.54TLB
-16.262 +-241.154
1.54BTB -105.135 -362.758
Max Fz 31659 2202 1.15DL
30719
+ 1.2SIDL
7203.169
+ 0.42CL +49.63
0.42PLA 102.787
+ 0.42PLB 260.732
+ 0.462TLA +231.201
0.462TLB - 0.462BTA
164.76 - 0.462BTB
Min Fz 31659 3171 1.15DL
30719
+ 1.2SIDL
-3052.583
+ 0.42CL +-42.6
0.42PLB +-98.258
0.462TLB
-281.718
+ 0.462BTB
-244.819
+ 0.3SLX-136.069
+ 0.3SLY + 1SLZ + 1.
Max Mx 31659 2202 1.15DL
30719
+ 1.2SIDL
7203.169
+ 0.42CL +49.63
0.42PLA 102.787
+ 0.42PLB 260.732
+ 0.462TLA +231.201
0.462TLB - 0.462BTA
164.76 - 0.462BTB
Min Mx 31659 2195 1.15DL
30719
+ 1.2SIDL
-3005.124
+ 0.42CL-43.385
+ 0.42PLA +-97.467
0.42PLB-281.894
+ 0.462TLA -245.749
+ 0.462TLB +-136.964
0.462BTA + 0.462BTB
Max My 31659 3171 1.15DL
30716
+ 1.2SIDL
6904.285
+ 0.42CL44.221
+ 0.42PLB +99.591
0.462TLB
247.443
+ 0.462BTB 339.91
+ 0.3SLX195.047
+ 0.3SLY + 1SLZ + 1.
Min My 31659 2202 1.15DL
30716
+ 1.2SIDL
-2753.698
+ 0.42CL-37.192
+ 0.42PLA +-95.062
0.42PLB-268.429
+ 0.462TLA -358.057
+ 0.462TLB --159.326
0.462BTA - 0.462BTB
Max Mz 31690 2104 1.15DL
30747
+ 1.2SIDL
6654.95
+ 1.4CL149.702
+ 1.4PLB + 1.54TLB
22.364 - 200.886
1.54BTB 104.604 531.664
Min Mz 31690 2114 1.15DL
30747
+ 1.2SIDL
-1432.217
- 1SLX --103.164
0.3SLY - 0.3SLZ
-31.255 -214.927 -163.049 -374.856

ODE MDE
Maximum Tension Force (kN) -2276.59 -3052.58
Skin Friction (kN) 2904.67
Final Axial Load (kN) 0.00 -147.92

2.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Provided

Dia. (mm) Nos.


19 16

2.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima 0 408.8 885.4 0.462 OK
Minima 7203 283.9 2862 0.099 OK

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 45 OK
Minima -65.94 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 2.257 OK 15.98 OK
Minima 1.37 OK 9.858 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

3.0 Shear Check at Bottom of Pile Cap

As per Cl. C5.2.8.9, pg. 5-64, AASHTO LRFD Bridge Design Specifications 2012,
Effective depth to be considered in the shear check
dv = 0.9 de
where de = D/2 + Dr
D = Dia of pile = 1.20 m
Dr = Dia of circle passing through the centres of longitudinal reinforcement
= 0.958 m
Hence de = 0.905 m and dv = 0.814 m
Horizontal resultant shear force at the section, Vu = 982 kN
Corresponding axial compressive force, N = 0 kN
Eff. width to be taken = diameter of section = bv = 1.20 m
Total vertical reinforcement at the section = 25736 mm2
Effective area of tensile steel = 50% of total steel = A s = 0.0129 m2
Percentage of tensile reinforcement = 100 As /(bv . dv) = 1.317 %
Horizontal shear force, Vu = 982 kN
Shear stress (vv = Vu /(bv . dv) = 1005.20 kN/m2
Grade of concrete = C40
As per Cl. 5.3.3.2, pg. 18, BS 5400-4: 1990, ultimate shear stress in concrete,
vc = 0.27/ m (100As/(bd))1/3 (fcu)1/3 (where m = 1.25) = 0.810 Mpa
= 810 kN/m2
Depth Factor, s = (500/d)1/4 or 0.70, whichever is greater = 0.885
Allowable shear stress in concrete, s vc = 716.675 kN/m2
Gross area of concrete section, Ac 1.131 m2
Increase in shear stress (1 + 0.05N/A c) is done as per Cl. 5.5.6, pg. 29, BS 5400-4: 1990,
n = (1 + 0.05N /Ac) = 1.00
Modified shear strength of concrete (n s vc ) = 716.68 kN/m2
Shear to be carried by stirrups, Vus = Vu - (n s vc ) bv dv = 281.98 kN
As per Table 7, pg. 18, BS 5400-4: 1990, minimum shear to be carried by stirrups,
Vus,min = 0.4 bv dv = 390.93 kN
Dia of stirrup = 13 mm
No. of legs = 2
As per Table 7, pg. 18, BS 5400-4: 1990, spacing required,
sv = 0.87 fyv Asv d / Vus = 188 mm
Provided spacing 180 mm
OK
Shear reinforcement 13mm dia @ 180mm c/c
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

4.0 Curtailment Check


4.1 Member Forces from STAAD at 12.0m below Bottom of Pile Cap

Static - LC 1001-1006
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31679 1005 1DL30739
+ 1SIDL 2506.631
+ 1CL + 1PLA -10.217
+ 1PLB + 1.1TLA
4.808
+ 1.1TLB
-29.468
+ 1.1BTA-33.669
+ 1.1BTB -97.028
Min Fx 31648 1003 1DL30708
+ 1SIDL 1633.393
+ 1CL + 1PLB +-6.655
1.1TLB + 1.1BTB
1.679 -21.018 -2.105 -32.97
Max Fy 31653 1006 1DL30713
+ 1SIDL 2240.985
+ 1CL + 1PLA +12.434
1PLB + 1.1TLA
5.524
+ 1.1TLB6.228
- 1.1BTA -39.576
- 1.1BTB 80.995
Min Fy 31681 1005 1DL30741
+ 1SIDL 2506.631
+ 1CL + 1PLA -11.416
+ 1PLB + 1.1TLA
4.573
+ 1.1TLB
-29.468
+ 1.1BTA-24.098
+ 1.1BTB -75.698
Max Fz 31684 1002 1DL30744
+ 1SIDL 2061.989
+ 1CL + 1PLA + 7.327
1.1TLA - 1.1BTA
5.957 -6.766 -34.99 54.908
Min Fz 31662 1005 1DL30721
+ 1SIDL 1642.353
+ 1CL + 1PLA +-0.924
1PLB + 1.1TLA
-0.795
+ 1.1TLB
-25.833
+ 1.1BTA +3.909
1.1BTB 3.26
Max Mx 31648 1006 1DL30708
+ 1SIDL 2240.985
+ 1CL + 1PLA + 1.681
1PLB + 1.1TLA
-0.698
+ 1.1TLB6.228
- 1.1BTA -52.852
- 1.1BTB 119.731
Min Mx 31679 1005 1DL30739
+ 1SIDL 2506.631
+ 1CL + 1PLA -10.217
+ 1PLB + 1.1TLA
4.808
+ 1.1TLB
-29.468
+ 1.1BTA-33.669
+ 1.1BTB -97.028
Max My 31654 1005 1DL30715
+ 1SIDL 1642.353
+ 1CL + 1PLA +-5.975
1PLB + 1.1TLA
0.136
+ 1.1TLB
-25.833
+ 1.1BTA +5.931
1.1BTB -10.507
Min My 31679 1002 1DL30739
+ 1SIDL 2061.989
+ 1CL + 1PLA +-1.895
1.1TLA - 1.1BTA
2.338 -6.766 -57.721 69.877
Max Mz 31648 1006 1DL30708
+ 1SIDL 2240.985
+ 1CL + 1PLA + 1.681
1PLB + 1.1TLA
-0.698
+ 1.1TLB6.228
- 1.1BTA -52.852
- 1.1BTB 119.731
Min Mz 31679 1005 1DL30739
+ 1SIDL 2506.631
+ 1CL + 1PLA -10.217
+ 1PLB + 1.1TLA
4.808
+ 1.1TLB
-29.468
+ 1.1BTA-33.669
+ 1.1BTB -97.028

ODE Seismic - LC 1001-1190, 2031-2078, 3031-3078, 4001-4032, 5009-5024 & 6009-6024


Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31648 1102 1DL30709
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
33.513
+ 0.3PLB74.047
+ 0.33TLA206.587
+ 0.33TLB -912.813
0.33BTA - 0.33BTB
402.044- 0.3SLX - 0.3S
Min Fx 31648 3071 1DL30709
+ 1SIDL-2276.594
+ 0.3CL + 0.3PLB
-38.972
+ 0.33TLB
-73.126
+ 0.33BTB
-224.775
+ 0.3SLX
-956.964
+ 0.3SLY-352.621
+ 1SLZ + 1.1NLB
Max Fy 31684 1086 1DL30745
+ 1SIDL 4856.862
+ 0.3CL + 0.3PLA
107.637
+ 0.3PLB35.192
+ 0.33TLA149.193
+ 0.33TLB -157.338
0.33BTA - 0.33BTB
524.536- 1SLX - 0.3SLY
Min Fy 31684 1079 1DL30745
+ 1SIDL +-806.849
0.3CL + 0.3PLA
-106.354
+ 0.3PLB-27.253
+ 0.33TLA
-177.245
+ 0.33TLB-194.075
+ 0.33BTA +-500.461
0.33BTB + 1SLX + 0.3S
Max Fz 31652 3047 1DL30712
+ 1SIDL 5781.025
+ 0.3CL + 0.3PLA
32.999
+ 0.33TLA
109.117
+ 0.33BTA
201.256
+ 0.3SLX
644.063
+ 0.3SLY 308.363
+ 1SLZ + 1.1NLA
Min Fz 31652 3071 1DL30713
+ 1SIDL-2276.594
+ 0.3CL + 0.3PLB
-33.949
+ 0.33TLB
-104.301
+ 0.33BTB
-224.775
+ 0.3SLX
-568.217
+ 0.3SLY-250.888
+ 1SLZ + 1.1NLB
Max Mx 31648 1102 1DL30709
+ 1SIDL 5869.343
+ 0.3CL + 0.3PLA
33.513
+ 0.3PLB74.047
+ 0.33TLA206.587
+ 0.33TLB -912.813
0.33BTA - 0.33BTB
402.044- 0.3SLX - 0.3S
Min Mx 31648 1095 1DL30709
+ 1SIDL-2242.695
+ 0.3CL + 0.3PLA
-40.126
+ 0.3PLB-71.982
+ 0.33TLA
-224.901
+ 0.33TLB-965.255
+ 0.33BTA +-360.884
0.33BTB + 0.3SLX + 0.
Max My 31648 3071 1DL30708
+ 1SIDL 5655.854
+ 0.3CL + 0.3PLB
31.092
+ 0.33TLB74.237
+ 0.33BTB
197.095
+ 0.3SLX994.69
+ 0.3SLY +349.351
1SLZ + 1.1NLB
Min My 31648 1054 1DL30708
+ 1SIDL +-2090.02
0.3CL + 0.3PLA
-37.538
+ 0.33TLA
-72.695
- 0.33BTA
-217.044
- 0.3SLX
-1040.129
- 0.3SLY --318.858
1SLZ
Max Mz 31679 1007 1DL30739
+ 1SIDL 4859.567
+ 1SLX + 0.3SLY54.503
+ 0.3SLZ 46.168 145.698 262.952 1007.948
Min Mz 31679 1014 1DL30739
+ 1SIDL --976.357
1SLX - 0.3SLY
-60.206
- 0.3SLZ -42.764 -172.411 -336.691 -1002.16
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

MDE Seismic - LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-2378, 3131-3178,4101-4132, 5109-


5124, 6109-6124
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31648 2202 1.15DL
30709
+ 1.2SIDL
7203.169
+ 0.42CL42.564
+ 0.42PLA +92.785
0.42PLB 260.732
+ 0.462TLA1146.868
+ 0.462TLB - 507.028
0.462BTA - 0.462BTB
Min Fx 31648 3171 1.15DL
30709
+ 1.2SIDL
-3052.583
+ 0.42CL-48.758
+ 0.42PLB +-91.911
0.462TLB
-281.718
+ 0.462BTB
-1196.051
+ 0.3SLX-446.416
+ 0.3SLY + 1SLZ + 1.
Max Fy 31683 2104 1.15DL
30743
+ 1.2SIDL
6654.95
+ 1.4CL +193.46
1.4PLB + 1.54TLB
15.102 - 200.886
1.54BTB 121.54 1266.687
Min Fy 31683 2103 1.15DL
30744
+ 1.2SIDL
-1745.136
+ 1.4CL-194.827
+ 1.4PLB + 1.54TLB
-6.711 +-241.154
1.54BTB -169.719 -1046.583
Max Fz 31652 3147 1.15DL
30712
+ 1.2SIDL
7079.524
+ 0.42CL41.164
+ 0.42PLA 136.826
+ 0.462TLA 253.267
+ 0.462BTA
809.495
+ 0.3SLX384.341
+ 0.3SLY + 1SLZ + 1.5
Min Fz 31652 3171 1.15DL
30713
+ 1.2SIDL
-3052.583
+ 0.42CL-42.951
+ 0.42PLB-131.396
+ 0.462TLB -281.718
+ 0.462BTB
-709.693
+ 0.3SLX-317.827
+ 0.3SLY + 1SLZ + 1.
Max Mx 31648 2202 1.15DL
30709
+ 1.2SIDL
7203.169
+ 0.42CL42.564
+ 0.42PLA +92.785
0.42PLB 260.732
+ 0.462TLA1146.868
+ 0.462TLB - 507.028
0.462BTA - 0.462BTB
Min Mx 31648 2195 1.15DL
30709
+ 1.2SIDL
-3005.124
+ 0.42CL-50.373
+ 0.42PLA + -90.31
0.42PLB-281.894
+ 0.462TLA-1207.659
+ 0.462TLB +-457.986
0.462BTA + 0.462BTB
Max My 31648 3171 1.15DL
30708
+ 1.2SIDL
6904.285
+ 0.42CL39.175
+ 0.42PLB + 93.05
0.462TLB
247.443
+ 0.462BTB
1253.226
+ 0.3SLX434.514
+ 0.3SLY + 1SLZ + 1.
Min My 31648 2154 1.15DL
30708
+ 1.2SIDL
-2791.379
+ 0.42CL-46.749
+ 0.42PLA +-91.308
0.462TLA
-270.895
- 0.462BTA
-1303.796
- 0.3SLX-398.956
- 0.3SLY - 1SLZ
Max Mz 31679 2104 1.15DL
30739
+ 1.2SIDL
6654.95
+ 1.4CL +97.142
1.4PLB + 1.54TLB
48.38 - 200.886
1.54BTB 53.301 1864.739
Min Mz 31679 2103 1.15DL
30740
+ 1.2SIDL
-1745.136
+ 1.4CL-106.806
+ 1.4PLB + 1.54TLB
-43.3 +-241.154
1.54BTB -147.753 -1756.607

ODE MDE
Maximum Tension Force (kN) -2276.59 -3052.58
Skin Friction (kN) 1110.67
Final Axial Load (kN) -1165.93 -1941.92

4.2 ULS & SLS Design Checks

Design checks for ULS adequacy, SLS stresses and surface crack width have been checked in Oasys.

Reinforcement Provided

Dia. (mm) Nos.


32 16

4.2.1 Oasys Results

ULS Adequacy for MDE

N M Mu
Case M/Mu
[kN] [kNm] [kNm]
Maxima -634.5 1763 1969 0.895 OK
Minima 7080 896.1 3743 0.239 OK
Project JMRT
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc. No. - Checked Reyaz
Title Design of Piles Verified Sumant

Reinforcement Stresses for ODE

Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2


From Oasys,
Stress in Reinforcement
Case
[N/mm²]
Maxima 65.47 OK
Minima -299.9 OK

Material Stresses for Static Case

Permissible Stresses Concrete 0.5fcu 20.000 N/mm2


Steel 0.75fy 292.500 N/mm2
(from table 2, pg. 8, BS 5400-4: 1990, for stress due to bending)

Stress in Concrete Stress in Reinforcement


Case
[N/mm²] [N/mm²]
Maxima 2.63 OK 17.92 OK
Minima 1.141 OK 8.637 OK

Surface Crack Width for Static Case

From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structure with severe exposure,
Permissible Crack Width = 0.250 mm
Maximum Crack Width per Face from Oasys = 0.000 mm OK
TOKYU-WIKA JOINT OPERATION
Jakarta Mass Rapid Transit Projects CP101 LEBAK BULUS STATION FOUNDATION DESIGN

Design of Pile

AECOM – 1 – TCD –ST1 - 0004 Appendix J


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR GROUP PG1


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Pile Group = PG1

No. of piles n = 1
Dia of pile = 1.00 m
Size of Column = 1.00 m x 1.00 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 1.50 m x 1.50 m


Area of pile cap = 2.25 m2
Depth of pile cap D = 1.50 m
Volume of pile cap = 3.38 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 84.38 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 1.88 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 37.50 kN

Total weight of (Pile cap + Earthfill) = 121.88 kN

2.0 Bottom Reinforcement


Bottom Reinforcement should be 0.06% of cross-sectional area.
Required Steel = 850.2 mm2/m
Dia 16 Spacing 225 Provided = 894 mm2/m
OK

3.0 Top Reinforcement


Top Reinforcement should be 0.06% of cross-sectional area.
Required Steel = 850.2 mm2/m
Dia 16 Spacing 225 Provided = 894 mm2/m
OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR GROUP PG1A


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nikhil
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Pile Group = PG1A

No. of piles n = 1
Dia of pile = 1.00 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 1.50 m x 2.40 m


Area of pile cap = 3.60 m2
Depth of pile cap D = 1.50 m
Volume of pile cap = 5.40 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 135.00 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 5.03 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 100.50 kN

Total weight of (Pile cap + Earthfill) = 235.50 kN

2.0 Bottom Reinforcement


Bottom Reinforcement should be 0.06% of cross-sectional area.
Required Steel = 850.2 mm2/m
Dia 16 Spacing 225 Provided = 894 mm2/m
OK

3.0 Top Reinforcement


Top Reinforcement should be 0.06% of cross-sectional area.
Required Steel = 850.2 mm2/m
Dia 16 Spacing 225 Provided = 894 mm2/m
OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR COLUMN C18


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Column No. = C18

No. of piles n = 4
Dia of pile = 1.20 m
Size of Column = 2.00 m x 2.00 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 5.30 m x 5.30 m


2
Area of pile cap = 28.09 m
Depth of pile cap D = 1.80 m
Volume of pile cap = 50.56 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 1264.05 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 36.14 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 722.70 kN

Total weight of (Pile cap + Earthfill) = 1986.75 kN

2.0 PILE LOADS

2.1 Summary of Staad Results (Forces at Bottom of Pile Cap)---

LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-


a) MDE Seismic
2378, 3131-3178,4101-4132, 5109-5124 & 6109-6124
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28078 2104 1.15DL
27058
+ 1.2SIDL
11225.74
+ 1.4CL 1087.246
+ 1.4PLB + 1.54TLB
322.166- 1.54BTB
35.780 1518.751 4374.685
Min Fx 28078 2103 1.15DL
27062
+ 1.2SIDL
-3479.51
+ 1.4CL-1029.826
+ 1.4PLB + -351.935
1.54TLB + 1.54BTB
-36.372 -960.045 -3210.861
Max Fy 28078 2103 1.15DL
27058
+ 1.2SIDL
10697.02
+ 1.4CL 1156.121
+ 1.4PLB + 1.54TLB
322.548+ 1.54BTB
35.023 1514.131 4627.226
Min Fy 28078 2104 1.15DL
27062
+ 1.2SIDL
-2950.79
+ 1.4CL-1098.701
+ 1.4PLB + -352.317
1.54TLB - 1.54BTB
-35.615 -955.807 -3394.528
Max Fz 28078 3171 1.15DL
27058
+ 1.2SIDL
9586.153
+ 0.42CL 256.249
+ 0.42PLB +978.231
0.462TLB +11.227
0.462BTB
4107.583
+ 0.3SLX + 0.3SLY
998.741+ 1SLZ + 1.54NLB
Min Fz 28078 3147 1.15DL
27062
+ 1.2SIDL
-2336.57
+ 0.42CL-188.467
+ 0.42PLA-1015.369
+ 0.462TLA +-12.783
0.462BTA
-2889.265
+ 0.3SLX + -635.212
0.3SLY + 1SLZ + 1.54NLA
Max Mx 28078 2104 1.15DL
27058
+ 1.2SIDL
11225.74
+ 1.4CL 1087.246
+ 1.4PLB + 1.54TLB
322.166- 1.54BTB
35.780 1518.751 4374.685
Min Mx 28078 2103 1.15DL
27062
+ 1.2SIDL
-3479.51
+ 1.4CL-1029.826
+ 1.4PLB + -351.935
1.54TLB + 1.54BTB
-36.372 -960.045 -3210.861
Max My 28078 3147 1.15DL
27058
+ 1.2SIDL
9773.19
+ 0.42CL 256.167
+ 0.42PLA +959.927
0.462TLA +12.653
0.462BTA4166.039
+ 0.3SLX + 0.3SLY
997.163+ 1SLZ + 1.54NLA
Min My 28078 3154 1.15DL
27058
+ 1.2SIDL
-2304.75
+ 0.42CL-208.941
+ 0.42PLA +-997.281
0.462TLA --14.336
0.462BTA-3915.576
- 0.3SLX - 0.3SLY
-895.138
- 1SLZ - 1.54NLA
Max Mz 28078 2103 1.15DL
27058
+ 1.2SIDL
10697.02
+ 1.4CL 1156.121
+ 1.4PLB + 1.54TLB
322.548+ 1.54BTB
35.023 1514.131 4627.226
Min Mz 28078 2104 1.15DL
27062
+ 1.2SIDL
-2950.79
+ 1.4CL-1098.701
+ 1.4PLB + -352.317
1.54TLB - 1.54BTB
-35.615 -955.807 -3394.528
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28079 2195 1.15DL
27059
+ 1.2SIDL
9924.301
+ 0.42CL 301.693
+ 0.42PLA +963.665
0.42PLB + 0.462TLA
12.384 + 0.462TLB
4140.027 + 0.462BTA
1302.533+ 0.462BTB + 0.3SLX + 0.3S
Min Fx 28079 2115 1.15DL
27063
+ 1.2SIDL
-2006.5
+ 0.3SLX-186.995
+ 0.3SLY +-1001.285
1SLZ -13.940 -2907.205 -541.465
Max Fy 28079 2103 1.15DL
27059
+ 1.2SIDL
8878.575
+ 1.4CL 1178.226
+ 1.4PLB + 1.54TLB
310.191+ 1.54BTB
35.685 1433.27 4809.514
Min Fy 28079 2104 1.15DL
27063
+ 1.2SIDL
-443.958
+ 1.4CL-1067.539
+ 1.4PLB + -340.728
1.54TLB - 1.54BTB
-36.269 -879.389 -3170.124
Max Fz 28079 3154 1.15DL
27063
+ 1.2SIDL
9484.138
+ 0.42CL 268.409
+ 0.42PLA +975.902
0.462TLA - 11.592
0.462BTA3087.597
- 0.3SLX - 0.3SLY
907.411
- 1SLZ - 1.54NLA
Min Fz 28079 3147 1.15DL
27063
+ 1.2SIDL
-1471.53
+ 0.42CL +-170.91
0.42PLA-1013.806
+ 0.462TLA +-13.249
0.462BTA
-2870.619
+ 0.3SLX + -489.615
0.3SLY + 1SLZ + 1.54NLA
Max Mx 28079 2104 1.15DL
27059
+ 1.2SIDL
8388.827
+ 1.4CL 1109.498
+ 1.4PLB + 1.54TLB
311.48- 1.54BTB
36.440 1424.257 4558.177
Min Mx 28079 2103 1.15DL
27063
+ 1.2SIDL45.79
+ 1.4CL +-998.811
1.4PLB + -342.017
1.54TLB + 1.54BTB
-37.025 -871.665 -2987.515
Max My 28079 3147 1.15DL
27059
+ 1.2SIDL
9756.336
+ 0.42CL 289.242
+ 0.42PLA +957.316
0.462TLA +13.183
0.462BTA
4153.269
+ 0.3SLX +1252.682
0.3SLY + 1SLZ + 1.54NLA
Min My 28079 3154 1.15DL
27059
+ 1.2SIDL
-1743.73
+ 0.42CL-191.743
+ 0.42PLA +-995.22
0.462TLA --14.840
0.462BTA
-3898.387
- 0.3SLX - 0.3SLY
-737.387
- 1SLZ - 1.54NLA
Max Mz 28079 2103 1.15DL
27059
+ 1.2SIDL
8878.575
+ 1.4CL 1178.226
+ 1.4PLB + 1.54TLB
310.191+ 1.54BTB
35.685 1433.27 4809.514
Min Mz 28079 2104 1.15DL
27063
+ 1.2SIDL
-443.958
+ 1.4CL-1067.539
+ 1.4PLB + -340.728
1.54TLB - 1.54BTB
-36.269 -879.389 -3170.124
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28080 2202 1.15DL
27064
+ 1.2SIDL
9728.217
+ 0.42CL 234.234
+ 0.42PLA + 0.42PLB
993.6 + 0.462TLA
11.654 + 0.462TLB
2927.23 - 0.462BTA
702.615- 0.462BTB - 0.3SLX - 0.3SLY
Min Fx 28080 2115 1.15DL
27064
+ 1.2SIDL
-2331.46
+ 0.3SLX-209.742
+ 0.3SLY + 1SLZ
-978.593 -13.048 -3067.49 -705.696
Max Fy 28080 2103 1.15DL
27060
+ 1.2SIDL
8425.392
+ 1.4CL 1153.026
+ 1.4PLB + 1.54TLB
335.777+ 1.54BTB
33.396 1205.976 4602.232
Min Fy 28080 2104 1.15DL
27064
+ 1.2SIDL
-642.971
+ 1.4CL-1095.722
+ 1.4PLB + -312.929
1.54TLB - 1.54BTB
-33.816 -1065.256 -3373.496
Max Fz 28080 3154 1.15DL
27064
+ 1.2SIDL
9478.685
+ 0.42CL 243.694
+ 0.42PLA +1000.67
0.462TLA - 10.815
0.462BTA2905.171
- 0.3SLX - 0.3SLY
728.932
- 1SLZ - 1.54NLA
Min Fz 28080 3147 1.15DL
27064
+ 1.2SIDL
-2186.1
+ 0.42CL-196.187
+ 0.42PLA +-988.583
0.462TLA +-12.350
0.462BTA
-3049.177
+ 0.3SLX + 0.3SLY
-672.12+ 1SLZ + 1.54NLA
Max Mx 28080 2104 1.15DL
27060
+ 1.2SIDL
8951.628
+ 1.4CL 1084.162
+ 1.4PLB + 1.54TLB
337.201- 1.54BTB
34.011 1195.848 4349.779
Min Mx 28080 2103 1.15DL
27064
+ 1.2SIDL
-1169.21
+ 1.4CL-1026.858
+ 1.4PLB + -314.354
1.54TLB + 1.54BTB
-34.430 -1056.552 -3189.907
Max My 28080 3147 1.15DL
27060
+ 1.2SIDL
9195.754
+ 0.42CL 264.567
+ 0.42PLA +982.045
0.462TLA +12.411
0.462BTA
3945.907
+ 0.3SLX +1049.821
0.3SLY + 1SLZ + 1.54NLA
Min My 28080 3154 1.15DL
27060
+ 1.2SIDL
-1903.17
+ 0.42CL +-217.06
0.42PLA +-969.957
0.462TLA --13.946
0.462BTA
-4102.001
- 0.3SLX - 0.3SLY
-945.501
- 1SLZ - 1.54NLA
Max Mz 28080 2103 1.15DL
27060
+ 1.2SIDL
8425.392
+ 1.4CL 1153.026
+ 1.4PLB + 1.54TLB
335.777+ 1.54BTB
33.396 1205.976 4602.232
Min Mz 28080 2104 1.15DL
27064
+ 1.2SIDL
-642.971
+ 1.4CL-1095.722
+ 1.4PLB + -312.929
1.54TLB - 1.54BTB
-33.816 -1065.256 -3373.496
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28081 2103 1.15DL
27061
+ 1.2SIDL
11182.5
+ 1.4CL 1181.323
+ 1.4PLB + 1.54TLB
348.099+ 1.54BTB
34.060 1286.288 4834.514
Min Fx 28081 2104 1.15DL
27065
+ 1.2SIDL
-2711.7
+ 1.4CL-1070.519
+ 1.4PLB + -324.484
1.54TLB - 1.54BTB
-34.472 -1141.115 -3191.159
Max Fy 28081 2103 1.15DL
27061
+ 1.2SIDL
11182.5
+ 1.4CL 1181.323
+ 1.4PLB + 1.54TLB
348.099+ 1.54BTB
34.060 1286.288 4834.514
Min Fy 28081 2104 1.15DL
27065
+ 1.2SIDL
-2711.7
+ 1.4CL-1070.519
+ 1.4PLB + -324.484
1.54TLB - 1.54BTB
-34.472 -1141.115 -3191.159
Max Fz 28081 3171 1.15DL
27061
+ 1.2SIDL
10102.92
+ 0.42CL 280.921
+ 0.42PLB 1002.953
+ 0.462TLB +11.4820.462BTB
3900.142
+ 0.3SLX + 1201.609
0.3SLY + 1SLZ + 1.54NLB
Min Fz 28081 3147 1.15DL
27065
+ 1.2SIDL
-2058.34
+ 0.42CL-163.188
+ 0.42PLA +-990.141
0.462TLA +-12.821
0.462BTA
-3067.732
+ 0.3SLX + -452.731
0.3SLY + 1SLZ + 1.54NLA
Max Mx 28081 2104 1.15DL
27061
+ 1.2SIDL
10690.27
+ 1.4CL 1112.583
+ 1.4PLB + 1.54TLB
347.853- 1.54BTB
34.673 1289.792 4583.088
Min Mx 28081 2103 1.15DL
27065
+ 1.2SIDL
-2219.47
+ 1.4CL +-1001.78
1.4PLB + -324.238
1.54TLB + 1.54BTB
-35.085 -1144.373 -3008.472
Max My 28081 3147 1.15DL
27061
+ 1.2SIDL
9916.186
+ 0.42CL +280.84
0.42PLA +984.651
0.462TLA +12.946
0.462BTA3958.588
+ 0.3SLX +1200.042
0.3SLY + 1SLZ + 1.54NLA
Min My 28081 3154 1.15DL
27061
+ 1.2SIDL
-2079.44
+ 0.42CL-183.623
+ 0.42PLA +-972.013
0.462TLA --14.455
0.462BTA-4119.101
- 0.3SLX - 0.3SLY
-687.039
- 1SLZ - 1.54NLA
Max Mz 28081 2103 1.15DL
27061
+ 1.2SIDL
11182.5
+ 1.4CL 1181.323
+ 1.4PLB + 1.54TLB
348.099+ 1.54BTB
34.060 1286.288 4834.514
Min Mz 28081 2104 1.15DL
27065
+ 1.2SIDL
-2711.7
+ 1.4CL-1070.519
+ 1.4PLB + -324.484
1.54TLB - 1.54BTB
-34.472 -1141.115 -3191.159
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

LC 1001-1190, 2031-2078, 3031-3078, 4001-


b) ODE Seismic
4032, 5009-5024 & 6009-6024
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28078 1102 1DL 27062
+ 1SIDL +8204.396
0.3CL + 0.3PLA
183.149
+ 0.3PLB771.395
+ 0.33TLA + 0.33TLB
9.477 - 0.33BTA
2504.49- 0.33BTB
535.457
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 28078 1015 1DL 27062
+ 1SIDL +-1912.48
0.3SLX + 0.3SLY
-159.177
+ 1SLZ -800.23 -10.773 -2323.797 -529.454
Max Fy 28078 1079 1DL 27058
+ 1SIDL +7958.232
0.3CL + 0.3PLA
604.116
+ 0.3PLB378.047
+ 0.33TLA + 19.153
0.33TLB + 1739.233
0.33BTA + 0.33BTB
2410.602+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 28078 1086 1DL 27058
+ 1SIDL +-1407.35
0.3CL + 0.3PLA
-562.545
+ 0.3PLB-410.916
+ 0.33TLA +-20.533
0.33TLB - -1507.135
0.33BTA - 0.33BTB
-2319.374
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 28078 3071 1DL 27058
+ 1SIDL +7846.913
0.3CL + 0.3PLB
204.587
+ 0.33TLB777.792
+ 0.33BTB8.956
+ 0.3SLX3281.775
+ 0.3SLY + 1SLZ
796.059
+ 1.1NLB
Min Fz 28078 3047 1DL 27062
+ 1SIDL +-1663.98
0.3CL + 0.3PLA
-149.75
+ 0.33TLA
-808.968
+ 0.33BTA-10.296
+ 0.3SLX-2299.132
+ 0.3SLY + 1SLZ
-507.301
+ 1.1NLA
Max Mx 28078 3062 1DL 27062
+ 1SIDL +8004.847
0.3CL + 0.3PLB
581.058
+ 0.33TLB375.471
- 0.33BTB19.868
- 1SLX - 1334.427
0.3SLY - 0.3SLZ
1746.884
- 1.1NLB
Min Mx 28078 3038 1DL 27058
+ 1SIDL + 0.3CL
-1608.5
+ 0.3PLA
-555.789
+ 0.33TLA
-404.673
- 0.33BTA-21.145
- 1SLX --1537.742
0.3SLY - 0.3SLZ
-2293.842
- 1.1NLA
Max My 28078 3047 1DL 27058
+ 1SIDL +7980.512
0.3CL + 0.3PLA
204.528
+ 0.33TLA764.718
+ 0.33BTA9.974
+ 0.3SLX 3323.529
+ 0.3SLY + 1SLZ
794.933
+ 1.1NLA
Min My 28078 3054 1DL 27058
+ 1SIDL +-1641.24
0.3CL + 0.3PLA
-164.375
+ 0.33TLA
-796.048
- 0.33BTA-11.406
- 0.3SLX-3111.204
- 0.3SLY - 1SLZ
-707.846
- 1.1NLA
Max Mz 28078 1079 1DL 27058
+ 1SIDL +7958.232
0.3CL + 0.3PLA
604.116
+ 0.3PLB378.047
+ 0.33TLA + 19.153
0.33TLB + 1739.233
0.33BTA + 0.33BTB
2410.602+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 28078 1086 1DL 27058
+ 1SIDL +-1407.35
0.3CL + 0.3PLA
-562.545
+ 0.3PLB-410.916
+ 0.33TLA +-20.533
0.33TLB - -1507.135
0.33BTA - 0.33BTB
-2319.374
- 1SLX - 0.3SLY - 0.3SLZ
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28079 1095 1DL 27059
+ 1SIDL +8089.645
0.3CL + 0.3PLA
241.009
+ 0.3PLB767.181
+ 0.33TLA + 0.33TLB
9.824 + 3303.865
0.33BTA + 0.33BTB
1044.281+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 28079 1015 1DL 27063
+ 1SIDL +-1355.84
0.3SLX + 0.3SLY
-146.008
+ 1SLZ -798.776 -11.162 -2310.468 -419.371
Max Fy 28079 1079 1DL 27059
+ 1SIDL +7048.284
0.3CL + 0.3PLA
625.992
+ 0.3PLB371.724
+ 0.33TLA + 19.596
0.33TLB + 1697.139
0.33BTA + 0.33BTB
2586.795+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 28079 1086 1DL 27059
+ 1SIDL + 0.3CL
-36.065
+ 0.3PLA
-540.14
+ 0.3PLB-405.038
+ 0.33TLA +-20.953
0.33TLB - -1461.486
0.33BTA - 0.33BTB
-2131.552
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 28079 3054 1DL 27063
+ 1SIDL +7775.242
0.3CL + 0.3PLA
217.234
+ 0.33TLA775.921
- 0.33BTA 9.258
- 0.3SLX2468.619
- 0.3SLY - 1SLZ736.586
- 1.1NLA
Min Fz 28079 3047 1DL 27063
+ 1SIDL +-973.723
0.3CL + 0.3PLA
-134.519
+ 0.33TLA
-807.719
+ 0.33BTA-10.668
+ 0.3SLX-2284.335
+ 0.3SLY + 1SLZ
-382.336
+ 1.1NLA
Max Mx 28079 3062 1DL 27063
+ 1SIDL +6765.038
0.3CL + 0.3PLB
602.003
+ 0.33TLB369.678
- 0.33BTB20.316
- 1SLX - 1293.682
0.3SLY - 0.3SLZ
1893.909
- 1.1NLB
Min Mx 28079 3038 1DL 27059
+ 1SIDL + 0.3CL
-126.79
+ 0.3PLA
-534.383
+ 0.33TLA
-398.987
- 0.33BTA-21.576
- 1SLX --1490.517
0.3SLY - 0.3SLZ
-2114.221
- 1.1NLA
Max My 28079 3047 1DL 27059
+ 1SIDL +7969.669
0.3CL + 0.3PLA
232.115
+ 0.33TLA762.646
+ 0.33BTA 10.395
+ 0.3SLX 3313.323
+ 0.3SLY + 1SLZ
1008.673
+ 1.1NLA
Min My 28079 3054 1DL 27059
+ 1SIDL +-1168.15
0.3CL + 0.3PLA
-149.399
+ 0.33TLA
-794.443
- 0.33BTA-11.805
- 0.3SLX-3097.243
- 0.3SLY - 1SLZ
-571.707
- 1.1NLA
Max Mz 28079 1079 1DL 27059
+ 1SIDL +7048.284
0.3CL + 0.3PLA
625.992
+ 0.3PLB371.724
+ 0.33TLA + 19.596
0.33TLB + 1697.139
0.33BTA + 0.33BTB
2586.795+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 28079 1086 1DL 27059
+ 1SIDL + 0.3CL
-36.065
+ 0.3PLA
-540.14
+ 0.3PLB-405.038
+ 0.33TLA +-20.953
0.33TLB - -1461.486
0.33BTA - 0.33BTB
-2131.552
- 1SLX - 0.3SLY - 0.3SLZ
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28080 1102 1DL 27064
+ 1SIDL +7917.544
0.3CL + 0.3PLA
189.52
+ 0.3PLB791.869
+ 0.33TLA + 0.33TLB
9.244 - 0.33BTA
2329.868- 0.33BTB566.441
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 28080 1015 1DL 27064
+ 1SIDL +-1632.83
0.3SLX + 0.3SLY
-165.61
+ 1SLZ -779.215 -10.448 -2448.83 -560.893
Max Fy 28080 1079 1DL 27060
+ 1SIDL +6774.244
0.3CL + 0.3PLA
604.602
+ 0.3PLB393.288
+ 0.33TLA + 18.331
0.33TLB + 0.33BTA
1510.43+ 0.33BTB
2410.896+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 28080 1086 1DL 27060
+ 1SIDL +-244.707
0.3CL + 0.3PLA
-563.087
+ 0.3PLB-382.263
+ 0.33TLA +-19.580
0.33TLB - -1639.269
0.33BTA - 0.33BTB
-2320.144
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 28080 3054 1DL 27064
+ 1SIDL +7739.306
0.3CL + 0.3PLA
196.277
+ 0.33TLA796.919
- 0.33BTA 8.644
- 0.3SLX2314.112
- 0.3SLY - 1SLZ585.239
- 1.1NLA
Min Fz 28080 3047 1DL 27064
+ 1SIDL + 0.3CL
-1529
+ 0.3PLA
-155.928
+ 0.33TLA
-786.351
+ 0.33BTA-9.950
+ 0.3SLX-2435.75
+ 0.3SLY + 1SLZ
-536.91
+ 1.1NLA
Max Mx 28080 3062 1DL 27064
+ 1SIDL +6804.305
0.3CL + 0.3PLB
581.555
+ 0.33TLB390.299
- 0.33BTB18.997
- 1SLX - 1136.499
0.3SLY - 0.3SLZ1746.188
- 1.1NLB
Min Mx 28080 3038 1DL 27060
+ 1SIDL +-422.945
0.3CL + 0.3PLA
-556.33
+ 0.33TLA
-377.213
- 0.33BTA-20.179
- 1SLX --1660.076
0.3SLY - 0.3SLZ
-2294.589
- 1.1NLA
Max My 28080 3047 1DL 27060
+ 1SIDL +7537.213
0.3CL + 0.3PLA
211.186
+ 0.33TLA783.615
+ 0.33BTA9.784
+ 0.3SLX 3137.653
+ 0.3SLY + 1SLZ
836.606
+ 1.1NLA
Min My 28080 3054 1DL 27060
+ 1SIDL +-1326.91
0.3CL + 0.3PLA
-170.837
+ 0.33TLA
-773.047
- 0.33BTA-11.089
- 0.3SLX -3269.86
- 0.3SLY - 1SLZ
-747.928
- 1.1NLA
Max Mz 28080 1079 1DL 27060
+ 1SIDL +6774.244
0.3CL + 0.3PLA
604.602
+ 0.3PLB393.288
+ 0.33TLA + 18.331
0.33TLB + 0.33BTA
1510.43+ 0.33BTB
2410.896+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 28080 1086 1DL 27060
+ 1SIDL +-244.707
0.3CL + 0.3PLA
-563.087
+ 0.3PLB-382.263
+ 0.33TLA +-19.580
0.33TLB - -1639.269
0.33BTA - 0.33BTB
-2320.144
- 1SLX - 0.3SLY - 0.3SLZ
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28081 1095 1DL 27061
+ 1SIDL +8363.084
0.3CL + 0.3PLA234.6
+ 0.3PLB791.358
+ 0.33TLA + 0.33TLB
9.656 + 3128.975
0.33BTA + 0.33BTB
1004.667+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 28081 1015 1DL 27065
+ 1SIDL + 0.3SLX
-1662.4+ 0.3SLY
-139.575
+ 1SLZ -780.666 -10.841 -2462.087 -387.953
Max Fy 28081 1079 1DL 27061
+ 1SIDL +8189.707
0.3CL + 0.3PLA
625.507
+ 0.3PLB399.593
+ 0.33TLA + 18.775
0.33TLB + 1552.254
0.33BTA + 0.33BTB
2586.517+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 28081 1086 1DL 27061
+ 1SIDL +-1198.83
0.3CL + 0.3PLA
-539.598
+ 0.3PLB-388.125
+ 0.33TLA +-20.002
0.33TLB - -1684.649
0.33BTA - 0.33BTB
-2130.796
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 28081 3071 1DL 27061
+ 1SIDL +8245.954
0.3CL + 0.3PLB
225.514
+ 0.33TLB798.757
+ 0.33BTB9.163
+ 0.3SLX3106.042
+ 0.3SLY + 1SLZ
968.133
+ 1.1NLB
Min Fz 28081 3047 1DL 27065
+ 1SIDL +-1424.95
0.3CL + 0.3PLA
-128.34
+ 0.33TLA
-787.596
+ 0.33BTA-10.326
+ 0.3SLX-2450.474
+ 0.3SLY + 1SLZ
-352.746
+ 1.1NLA
Max Mx 28081 3062 1DL 27065
+ 1SIDL +7889.906
0.3CL + 0.3PLB
601.507
+ 0.33TLB396.076
- 0.33BTB19.447
- 1SLX - 1176.968
0.3SLY - 0.3SLZ1894.621
- 1.1NLB
Min Mx 28081 3038 1DL 27061
+ 1SIDL +-1266.64
0.3CL + 0.3PLA
-533.844
+ 0.33TLA
-382.883
- 0.33BTA-20.612
- 1SLX - 0.3SLY
-1707.03- 0.3SLZ
-2113.489
- 1.1NLA
Max My 28081 3047 1DL 27061
+ 1SIDL +8112.575
0.3CL + 0.3PLA
225.456
+ 0.33TLA785.683
+ 0.33BTA 10.209
+ 0.3SLX 3147.789
+ 0.3SLY + 1SLZ
967.013
+ 1.1NLA
Min My 28081 3054 1DL 27061
+ 1SIDL +-1440.02
0.3CL + 0.3PLA
-142.936
+ 0.33TLA
-774.647
- 0.33BTA-11.493
- 0.3SLX-3283.751
- 0.3SLY - 1SLZ
-531.639
- 1.1NLA
Max Mz 28081 1079 1DL 27061
+ 1SIDL +8189.707
0.3CL + 0.3PLA
625.507
+ 0.3PLB399.593
+ 0.33TLA + 18.775
0.33TLB + 1552.254
0.33BTA + 0.33BTB
2586.517+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 28081 1086 1DL 27061
+ 1SIDL +-1198.83
0.3CL + 0.3PLA
-539.598
+ 0.3PLB-388.125
+ 0.33TLA +-20.002
0.33TLB - -1684.649
0.33BTA - 0.33BTB
-2130.796
- 1SLX - 0.3SLY - 0.3SLZ

c) Static LC 1001-1006
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28078 1006 1DL 27058
+ 1SIDL +4484.378
1CL + 1PLA + 1PLB
-21.88+ 1.1TLA
-20.257
+ 1.1TLB --0.706
1.1BTA - 1.1BTB
151.063 -118.265
Min Fx 28078 1003 1DL 27058
+ 1SIDL +3421.728
1CL + 1PLB + 49.273
1.1TLB + 1.1BTB
-17.04 -0.758 136.168 145.577
Max Fy 28078 1005 1DL 27058
+ 1SIDL +3772.961
1CL + 1PLA + 76.629
1PLB + 1.1TLA
-26.834
+ 1.1TLB +-0.915
1.1BTA + 171.824
1.1BTB 242.684
Min Fy 28078 1006 1DL 27058
+ 1SIDL +4484.378
1CL + 1PLA + 1PLB
-21.88+ 1.1TLA
-20.257
+ 1.1TLB --0.706
1.1BTA - 1.1BTB
151.063 -118.265
Max Fz 28078 1003 1DL 27058
+ 1SIDL +3421.728
1CL + 1PLB + 49.273
1.1TLB + 1.1BTB
-17.04 -0.758 136.168 145.577
Min Fz 28078 1005 1DL 27058
+ 1SIDL +3772.961
1CL + 1PLA + 76.629
1PLB + 1.1TLA
-26.834
+ 1.1TLB +-0.915
1.1BTA + 171.824
1.1BTB 242.684
Max Mx 28078 1004 1DL 27058
+ 1SIDL +3799.384
1CL + 1PLB + 1.1TLB
0.076 - 1.1BTB
-17.313 -0.218 139.468 -34.81
Min Mx 28078 1002 1DL 27058
+ 1SIDL +3942.867
1CL + 1PLA + 0.355
1.1TLA - -17.554
1.1BTA -1.062 116.458 -34.975
Max My 28078 1005 1DL 27058
+ 1SIDL +3772.961
1CL + 1PLA + 76.629
1PLB + 1.1TLA
-26.834
+ 1.1TLB +-0.915
1.1BTA + 171.824
1.1BTB 242.684
Min My 28078 1002 1DL 27062
+ 1SIDL +3942.867
1CL + 1PLA + 0.355
1.1TLA - -17.554
1.1BTA -1.062 98.904 -35.33
Max Mz 28078 1005 1DL 27058
+ 1SIDL +3772.961
1CL + 1PLA + 76.629
1PLB + 1.1TLA
-26.834
+ 1.1TLB +-0.915
1.1BTA + 171.824
1.1BTB 242.684
Min Mz 28078 1006 1DL 27058
+ 1SIDL +4484.378
1CL + 1PLA + 1PLB
-21.88+ 1.1TLA
-20.257
+ 1.1TLB --0.706
1.1BTA - 1.1BTB
151.063 -118.265
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28079 1005 1DL 27059
+ 1SIDL +4789.497
1CL + 1PLA +105.253
1PLB + 1.1TLA
-28.287
+ 1.1TLB +-0.888
1.1BTA + 183.639
1.1BTB 477.983
Min Fx 28079 1004 1DL 27059
+ 1SIDL +3719.138
1CL + 1PLB + 25.188
1.1TLB - 1.1BTB
-17.007 -0.209 136.941 171.625
Max Fy 28079 1005 1DL 27059
+ 1SIDL +4789.497
1CL + 1PLA +105.253
1PLB + 1.1TLA
-28.287
+ 1.1TLB +-0.888
1.1BTA + 183.639
1.1BTB 477.983
Min Fy 28079 1006 1DL 27059
+ 1SIDL +4043.905
1CL + 1PLA + 1PLB
6.816
+ 1.1TLA
-19.321
+ 1.1TLB --0.695
1.1BTA - 1.1BTB
143.378 117.638
Max Fz 28079 1004 1DL 27059
+ 1SIDL +3719.138
1CL + 1PLB + 25.188
1.1TLB - 1.1BTB
-17.007 -0.209 136.941 171.625
Min Fz 28079 1005 1DL 27059
+ 1SIDL +4789.497
1CL + 1PLA +105.253
1PLB + 1.1TLA
-28.287
+ 1.1TLB +-0.888
1.1BTA + 183.639
1.1BTB 477.983
Max Mx 28079 1004 1DL 27059
+ 1SIDL +3719.138
1CL + 1PLB + 25.188
1.1TLB - 1.1BTB
-17.007 -0.209 136.941 171.625
Min Mx 28079 1002 1DL 27059
+ 1SIDL +3867.649
1CL + 1PLA + 26.133
1.1TLA - -17.255
1.1BTA -1.053 113.976 176.939
Max My 28079 1005 1DL 27059
+ 1SIDL +4789.497
1CL + 1PLA +105.253
1PLB + 1.1TLA
-28.287
+ 1.1TLB +-0.888
1.1BTA + 183.639
1.1BTB 477.983
Min My 28079 1002 1DL 27063
+ 1SIDL +3867.649
1CL + 1PLA + 26.133
1.1TLA - -17.255
1.1BTA -1.053 96.722 150.805
Max Mz 28079 1005 1DL 27059
+ 1SIDL +4789.497
1CL + 1PLA +105.253
1PLB + 1.1TLA
-28.287
+ 1.1TLB +-0.888
1.1BTA + 183.639
1.1BTB 477.983
Min Mz 28079 1006 1DL 27063
+ 1SIDL +4043.905
1CL + 1PLA + 1PLB
6.816
+ 1.1TLA
-19.321
+ 1.1TLB --0.695
1.1BTA - 1.1BTB
124.058 110.822
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28080 1006 1DL 27060
+ 1SIDL +4514.154
1CL + 1PLA + 1PLB
-22
+ 1.1TLA
9.496
+ 1.1TLB --0.722
1.1BTA - 1.1BTB
-93.518 -119.259
Min Fx 28080 1001 1DL 27060
+ 1SIDL +3372.254
1CL + 1PLA + 50.093
1.1TLA + 1.1BTA
0.085 -0.602 -60.892 149.067
Max Fy 28080 1005 1DL 27060
+ 1SIDL +3716.364
1CL + 1PLA + 76.631
1PLB + 1.1TLA
0.336
+ 1.1TLB +-0.728
1.1BTA + 1.1BTB
-51.662 242.683
Min Fy 28080 1006 1DL 27060
+ 1SIDL +4514.154
1CL + 1PLA + 1PLB
-22
+ 1.1TLA
9.496
+ 1.1TLB --0.722
1.1BTA - 1.1BTB
-93.518 -119.259
Max Fz 28080 1006 1DL 27060
+ 1SIDL +4514.154
1CL + 1PLA + 1PLB
-22
+ 1.1TLA
9.496
+ 1.1TLB --0.722
1.1BTA - 1.1BTB
-93.518 -119.259
Min Fz 28080 1001 1DL 27060
+ 1SIDL +3372.254
1CL + 1PLA + 50.093
1.1TLA + 1.1BTA
0.085 -0.602 -60.892 149.067
Max Mx 28080 1004 1DL 27060
+ 1SIDL +3942.465
1CL + 1PLB + -0.294
1.1TLB - 1.1BTB
8.475 -0.192 -72.543 -37.859
Min Mx 28080 1002 1DL 27060
+ 1SIDL + 3794.16
1CL + 1PLA + 0.651
1.1TLA - 1.1BTA
8.228 -1.035 -95.514 -32.551
Max My 28080 1005 1DL 27064
+ 1SIDL +3716.364
1CL + 1PLA + 76.631
1PLB + 1.1TLA
0.336
+ 1.1TLB +-0.728
1.1BTA + 1.1BTB
-51.327 166.052
Min My 28080 1002 1DL 27060
+ 1SIDL + 3794.16
1CL + 1PLA + 0.651
1.1TLA - 1.1BTA
8.228 -1.035 -95.514 -32.551
Max Mz 28080 1005 1DL 27060
+ 1SIDL +3716.364
1CL + 1PLA + 76.631
1PLB + 1.1TLA
0.336
+ 1.1TLB +-0.728
1.1BTA + 1.1BTB
-51.662 242.683
Min Mz 28080 1006 1DL 27060
+ 1SIDL +4514.154
1CL + 1PLA + 1PLB
-22
+ 1.1TLA
9.496
+ 1.1TLB --0.722
1.1BTA - 1.1BTB
-93.518 -119.259
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 28081 1005 1DL 27061
+ 1SIDL +4732.899
1CL + 1PLA +105.251
1PLB + 1.1TLA
1.788
+ 1.1TLB +-0.701
1.1BTA + 1.1BTB
-63.476 477.985
Min Fx 28081 1002 1DL 27061
+ 1SIDL +3718.941
1CL + 1PLA + 25.838
1.1TLA - 1.1BTA
7.928 -1.025 -93.032 174.515
Max Fy 28081 1005 1DL 27061
+ 1SIDL +4732.899
1CL + 1PLA +105.251
1PLB + 1.1TLA
1.788
+ 1.1TLB +-0.701
1.1BTA + 1.1BTB
-63.476 477.985
Min Fy 28081 1006 1DL 27061
+ 1SIDL +4073.679
1CL + 1PLA + 1PLB
6.936
+ 1.1TLA8.56
+ 1.1TLB --0.711
1.1BTA - 1.1BTB
-85.834 118.631
Max Fz 28081 1006 1DL 27061
+ 1SIDL +4073.679
1CL + 1PLA + 1PLB
6.936
+ 1.1TLA8.56
+ 1.1TLB --0.711
1.1BTA - 1.1BTB
-85.834 118.631
Min Fz 28081 1001 1DL 27061
+ 1SIDL +4026.568
1CL + 1PLA + 75.053
1.1TLA + 1.1BTA
0.981 -0.577 -68.171 354.278
Max Mx 28081 1004 1DL 27061
+ 1SIDL +3862.219
1CL + 1PLB + 25.558
1.1TLB - 1.1BTB
8.169 -0.183 -70.015 174.674
Min Mx 28081 1002 1DL 27061
+ 1SIDL +3718.941
1CL + 1PLA + 25.838
1.1TLA - 1.1BTA
7.928 -1.025 -93.032 174.515
Max My 28081 1005 1DL 27065
+ 1SIDL +4732.899
1CL + 1PLA +105.251
1PLB + 1.1TLA
1.788
+ 1.1TLB +-0.701
1.1BTA + 1.1BTB
-61.687 372.734
Min My 28081 1002 1DL 27061
+ 1SIDL +3718.941
1CL + 1PLA + 25.838
1.1TLA - 1.1BTA
7.928 -1.025 -93.032 174.515
Max Mz 28081 1005 1DL 27061
+ 1SIDL +4732.899
1CL + 1PLA +105.251
1PLB + 1.1TLA
1.788
+ 1.1TLB +-0.701
1.1BTA + 1.1BTB
-63.476 477.985
Min Mz 28081 1006 1DL 27065
+ 1SIDL +4073.679
1CL + 1PLA + 1PLB
6.936
+ 1.1TLA8.56
+ 1.1TLB --0.711
1.1BTA - 1.1BTB
-77.274 111.695

2.2 Pile Loads

MDE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 11226 9924 9728 11183


Min Fx -3480 -2006 -2331 -2712
Max Fy 10697 8879 8425 11183
Min Fy -2951 -444 -643 -2712
Max Fz 9586 9484 9479 10103
Min Fz -2337 -1472 -2186 -2058
Max Mx 11226 8389 8952 10690
Min Mx -3480 46 -1169 -2219
Max My 9773 9756 9196 9916
Min My -2305 -1744 -1903 -2079
Max Mz 10697 8879 8425 11183
Min Mz -2951 -444 -643 -2712
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

ODE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 8204 8090 7918 8363


Min Fx -1912 -1356 -1633 -1662
Max Fy 7958 7048 6774 8190
Min Fy -1407 -36 -245 -1199
Max Fz 7847 7775 7739 8246
Min Fz -1664 -974 -1529 -1425
Max Mx 8005 6765 6804 7890
Min Mx -1609 -127 -423 -1267
Max My 7981 7970 7537 8113
Min My -1641 -1168 -1327 -1440
Max Mz 7958 7048 6774 8190
Min Mz -1407 -36 -245 -1199

Static
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 4484 4789 4514 4733


Min Fx 3422 3719 3372 3719
Max Fy 3773 4789 3716 4733
Min Fy 4484 4044 4514 4074
Max Fz 3422 3719 4514 4074
Min Fz 3773 4789 3372 4027
Max Mx 3799 3719 3942 3862
Min Mx 3943 3868 3794 3719
Max My 3773 4789 3716 4733
Min My 3943 3868 3794 3719
Max Mz 3773 4789 3716 4733
Min Mz 4484 4044 4514 4074

3.1 Moment at Bottom Face:

Lever arm Z = Pile Centre to column face

Z = 0.80 m

Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or


2.0 m (P1+P2)xZ or (P3+P4)xZ, whichever
column is maximum

P kN
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = 510.276 kN.m
Design Moment, M = M1 - M2

Case M1 (kN.m) M = (M1 - M2) (kN.m)


MDE Seismic 16920.000 16333.182
ODE Seismic 13162.400 12652.124
Static 7617.600 7107.324

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
2
K = Mu/bd fcu = 0.021 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1710.50 mm
Hence, z = 0.95 d = 1624.98 mm
As = Mu / (fy z)
Ast = 25772.677 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


29 120 0 0 0 0

= 28716.101 mm2 OK

3.2 Moment at Top Face:

Lever arm Z = Pile Centre to column face

P kN Z = 0.80 m
2.0 m
column Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or
(P1+P2)xZ or (P3+P4)xZ, whichever
is minimum

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = -510.276 kN.m
Design Moment, M = M1 + M2

Case M1 (kN.m) M = (M1 + M2) (kN.m)


MDE Seismic -4648.800 -5235.618
ODE Seismic -2836.000 -3346.276
Static 0.000 0.000

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

K = Mu/bd2fcu = 0.007 K'


Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.95 d = 1626.88 mm
As = M u / (f y z)
Ast = 8251.808 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 120 0 0 0 0

= 21357.103 mm2 OK

3.3 Moment Capacity, Stress and Crack Width Check from Oasys

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 16330 18360 0.8896 OK
Minima
2 0.0 5236 13770 0.3804 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
41.27 OK
41.27 OK
Minima
-210.4 OK
-210.4 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fcu 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Oasys Results
Cocncrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
3 4.356 OK 3 22.65 OK
3 4.356 OK 3 22.65 OK
Minima Minima
3 -0.5875 OK 3 -95.83 OK
3 -0.5875 OK 3 -95.83 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.160 mm OK

3.4 Minimum Reinforcement


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4007.25 mm2/m
2
At bottom face, Provided = 5418 mm2/m
Astprovided > Astmin OK
At top face, Provided = 4030 mm2/m
Astprovided > Astmin OK

4.0 Shear Check


Total pile reaction, V1 = 21150 kN
As per Cl. 3.11.4.3, pg. 82, BS 8110-1: 1997, critical section for shear should be located 20% of the pile diameter inside
Distance of critical section for shear check from column face = 0.440 m
Factored weight per unit length due to soil and pile cap = 431.087 kN/m
Hence, downward reaction due to soil and pile cap weight,
V2 = weight per unit length x (length of pile cap - 0.5 x column size - distance of critical section)
V2 = 522 kN
Net reaction, Vu = V1 - V2 = 20628 kN
Width of pile cap available b = 5.300 m
Effective depth of pile cap d = 1.711 m
Area of tensile steel provided As = 28716 mm2
= 0.029 m2
Percentage of tensile steel provided 100As/(b.d) = 0.317 %
Shear stress = Vu /(b.d) = 2275.44 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.35 MPa
= 350 kN/sqm
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

As per Cl. 3.11.4.4, pg. 82, BS 8110-1:1997,


Enhanced shear strength of concrete, say vc,1 = 2.d.vc /av
av = 0.440 m
Therefore, vc,1 = 2.72 MPa
= 2721 kN/sqm
Vus = Vu - vc,1 b d = -4041.52 kN

Requirement of shear reinforcement = Not Required

5.0 Check for punching shear


Total pile load = 42061 kN
From section 1.0 above, factored weight of pile cap + earthfill = 1987 kN
Hence, net punching shear force = 40074 kN
Effective depth of pile cap = 1.711 m
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, punching shear shall be checked at the perimeter of the column.
Shear perimeter = 8.000 m
Shearing Area = 13.684 m2
Punching Shear stress = 2928.548 kN/m2
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997,
Allowable punching shear stress = lesser of 0.8 fcu or 5 N/mm2 = 5.00 N/mm2
= 5000.000 kN/m2
OK
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, since the pile spacing is not greater than 3 times the pile diameter, no
additional punching shear check is required.
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR COLUMN C20 & 22


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Column No. = C20 & 22

No. of piles n = 4
Dia of pile = 1.20 m
Size of Column = 2.00 m x 2.00 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 5.30 m x 5.30 m


2
Area of pile cap = 28.09 m
Depth of pile cap D = 1.80 m
Volume of pile cap = 50.56 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 1264.05 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 36.14 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 722.70 kN

Total weight of (Pile cap + Earthfill) = 1986.75 kN

2.0 PILE LOADS

2.1 Summary of Staad Results (Forces at Bottom of Pile Cap)---

LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-


a) MDE Seismic
2378, 3131-3178,4101-4132, 5109-5124 & 6109-6124
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30774 2104 1.15DL
29830
+ 1.2SIDL
10962.08
+ 1.4CL 1097.345
+ 1.4PLB + 1.54TLB
204.262- 1.54BTB
34.964 1085.686 4398.595
Min Fx 30774 2115 1.15DL
29834
+ 1.2SIDL
-2557.09
+ 0.3SLX-205.187
+ 0.3SLY + 1SLZ
-974.131 -13.420 -2815.189 -676.335
Max Fy 30898 2103 1.15DL
29954
+ 1.2SIDL
9823.658
+ 1.4CL 1182.453
+ 1.4PLB + 1.54TLB
104.984+ 1.54BTB
32.000 704.337 4733.031
Min Fy 30774 2104 1.15DL
29834
+ 1.2SIDL
-1915.64
+ 1.4CL-1113.521
+ 1.4PLB + -246.066
1.54TLB - 1.54BTB
-35.614 -574.999 -3438.619
Max Fz 30774 3154 1.15DL
29834
+ 1.2SIDL
9864.065
+ 0.42CL +236.12
0.42PLA +948.453
0.462TLA - 11.492
0.462BTA2990.491
- 0.3SLX - 0.3SLY
683.891
- 1SLZ - 1.54NLA
Min Fz 30774 3178 1.15DL
29830
+ 1.2SIDL
-2019.09
+ 0.42CL-213.543
+ 0.42PLB +-984.942
0.462TLB-12.831
- 0.462BTB
-3697.539
- 0.3SLX - 0.3SLY
-915.353
- 1SLZ - 1.54NLB
Max Mx 30774 2104 1.15DL
29830
+ 1.2SIDL
10962.08
+ 1.4CL 1097.345
+ 1.4PLB + 1.54TLB
204.262- 1.54BTB
34.964 1085.686 4398.595
Min Mx 30774 2103 1.15DL
29834
+ 1.2SIDL
-2404.45
+ 1.4CL +-1037.31
1.4PLB + -247.323
1.54TLB + 1.54BTB
-36.324 -574.427 -3224.79
Max My 30774 3147 1.15DL
29830
+ 1.2SIDL
9807.961
+ 0.42CL 258.875
+ 0.42PLA +932.028
0.462TLA +12.776
0.462BTA
4020.934
+ 0.3SLX +1003.458
0.3SLY + 1SLZ + 1.54NLA
Min My 30774 3154 1.15DL
29830
+ 1.2SIDL
-2032.86
+ 0.42CL-213.266
+ 0.42PLA +-966.474
0.462TLA --14.011
0.462BTA
-3785.939
- 0.3SLX - 0.3SLY
-914.589
- 1SLZ - 1.54NLA
Max Mz 30898 2103 1.15DL
29954
+ 1.2SIDL
9823.658
+ 1.4CL 1182.453
+ 1.4PLB + 1.54TLB
104.984+ 1.54BTB
32.000 704.337 4733.031
Min Mz 30774 2104 1.15DL
29834
+ 1.2SIDL
-1915.64
+ 1.4CL-1113.521
+ 1.4PLB + -246.066
1.54TLB - 1.54BTB
-35.614 -574.999 -3438.619
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30899 2195 1.15DL
29955
+ 1.2SIDL
10407.32
+ 0.42CL 311.187
+ 0.42PLA + 0.42PLB
905.67 + 0.462TLA
12.495 + 0.462TLB
3922.269 + 0.462BTA
1350.156+ 0.462BTB + 0.3SLX + 0.3S
Min Fx 30775 2115 1.15DL
29835
+ 1.2SIDL
-2101.62
+ 0.3SLX-190.949
+ 0.3SLY + 1SLZ
-972.526 -14.158 -2799.85 -555.118
Max Fy 30899 2103 1.15DL
29955
+ 1.2SIDL
10094.4
+ 1.4CL +1209.91
1.4PLB + 1.54TLB
97.192+ 1.54BTB
32.220 658.423 4958.816
Min Fy 30775 2104 1.15DL
29835
+ 1.2SIDL
-605.356
+ 1.4CL-1081.937
+ 1.4PLB + -235.549
1.54TLB - 1.54BTB
-36.019 -505.653 -3210.801
Max Fz 30775 3154 1.15DL
29835
+ 1.2SIDL
9789.129
+ 0.42CL 270.616
+ 0.42PLA +946.509
0.462TLA - 12.233
0.462BTA2977.523
- 0.3SLX - 0.3SLY
914.578
- 1SLZ - 1.54NLA
Min Fz 30775 3178 1.15DL
29831
+ 1.2SIDL
-1684.5
+ 0.42CL +-195.85
0.42PLB +-983.124
0.462TLB-13.551
- 0.462BTB
-3681.796
- 0.3SLX - 0.3SLY
-754.036
- 1SLZ - 1.54NLB
Max Mx 30775 2104 1.15DL
29831
+ 1.2SIDL
9358.045
+ 1.4CL 1124.951
+ 1.4PLB + 1.54TLB
194.547- 1.54BTB
35.392 1000.043 4625.758
Min Mx 30775 2103 1.15DL
29835
+ 1.2SIDL
-98.69
+ 1.4CL +-1005.71
1.4PLB + -238.354
1.54TLB + 1.54BTB
-36.724 -494.025 -2996.857
Max My 30775 3147 1.15DL
29831
+ 1.2SIDL
10030.19
+ 0.42CL 293.633
+ 0.42PLA +929.623
0.462TLA +13.552
0.462BTA
4009.912
+ 0.3SLX +1273.284
0.3SLY + 1SLZ + 1.54NLA
Min My 30775 3154 1.15DL
29831
+ 1.2SIDL
-1693.82
+ 0.42CL-195.449
+ 0.42PLA +-964.663
0.462TLA --14.769
0.462BTA-3770.14
- 0.3SLX - 0.3SLY
-752.223
- 1SLZ - 1.54NLA
Max Mz 30899 2103 1.15DL
29955
+ 1.2SIDL
10094.4
+ 1.4CL +1209.91
1.4PLB + 1.54TLB
97.192+ 1.54BTB
32.220 658.423 4958.816
Min Mz 30775 2104 1.15DL
29835
+ 1.2SIDL
-605.356
+ 1.4CL-1081.937
+ 1.4PLB + -235.549
1.54TLB - 1.54BTB
-36.019 -505.653 -3210.801
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30900 2202 1.15DL
29960
+ 1.2SIDL
10066.72
+ 0.42CL 236.022
+ 0.42PLA +938.608
0.42PLB + 0.462TLA
11.461 + 0.462TLB
2747.201 - 0.462BTA
701.229- 0.462BTB - 0.3SLX - 0.3SLY
Min Fx 30776 2115 1.15DL
29836
+ 1.2SIDL
-2397.93
+ 0.3SLX-213.513
+ 0.3SLY + 1SLZ
-949.857 -13.016 -2961.74 -718.075
Max Fy 30900 2103 1.15DL
29956
+ 1.2SIDL
9226.288
+ 1.4CL 1181.699
+ 1.4PLB + 1.54TLB
125.461+ 1.54BTB
30.357 425.71 4726.898
Min Fy 30776 2104 1.15DL
29836
+ 1.2SIDL
-460.654
+ 1.4CL-1111.666
+ 1.4PLB + 1.54TLB
-205.84- 1.54BTB
-33.782 -719.733 -3425.463
Max Fz 30776 3154 1.15DL
29836
+ 1.2SIDL
9644.409
+ 0.42CL 244.569
+ 0.42PLA +972.452
0.462TLA - 11.201
0.462BTA2788.398
- 0.3SLX - 0.3SLY
726.522
- 1SLZ - 1.54NLA
Min Fz 30776 3178 1.15DL
29832
+ 1.2SIDL
-1869.13
+ 0.42CL-221.933
+ 0.42PLB +-956.937
0.462TLB-12.440
- 0.462BTB
-3895.038
- 0.3SLX - 0.3SLY
-968.48
- 1SLZ - 1.54NLB
Max Mx 30776 2104 1.15DL
29832
+ 1.2SIDL
9530.465
+ 1.4CL 1095.324
+ 1.4PLB + 1.54TLB
224.194- 1.54BTB
33.159 755.814 4382.198
Min Mx 30776 2103 1.15DL
29836
+ 1.2SIDL
-970.897
+ 1.4CL-1035.426
+ 1.4PLB + -208.658
1.54TLB + 1.54BTB
-34.335 -708.008 -3211.423
Max My 30776 3147 1.15DL
29832
+ 1.2SIDL
9402.135
+ 0.42CL 267.591
+ 0.42PLA +955.561
0.462TLA +12.532
0.462BTA3794.64
+ 0.3SLX +1059.217
0.3SLY + 1SLZ + 1.54NLA
Min My 30776 3154 1.15DL
29832
+ 1.2SIDL
-1859.99
+ 0.42CL-221.531
+ 0.42PLA +-938.476
0.462TLA --13.620
0.462BTA
-3983.376
- 0.3SLX - 0.3SLY
-966.662
- 1SLZ - 1.54NLA
Max Mz 30900 2103 1.15DL
29956
+ 1.2SIDL
9226.288
+ 1.4CL 1181.699
+ 1.4PLB + 1.54TLB
125.461+ 1.54BTB
30.357 425.71 4726.898
Min Mz 30776 2104 1.15DL
29836
+ 1.2SIDL
-460.654
+ 1.4CL-1111.666
+ 1.4PLB + 1.54TLB
-205.84- 1.54BTB
-33.782 -719.733 -3425.463
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30777 2103 1.15DL
29833
+ 1.2SIDL
11298.35
+ 1.4CL +1203.17
1.4PLB + 1.54TLB
232.634+ 1.54BTB
33.041 843.356 4932.094
Min Fx 30777 2115 1.15DL
29837
+ 1.2SIDL
-2352.44
+ 0.3SLX-182.631
+ 0.3SLY + 1SLZ
-951.462 -13.757 -2977.075 -513.499
Max Fy 30901 2103 1.15DL
29957
+ 1.2SIDL
10608.69
+ 1.4CL 1210.666
+ 1.4PLB + 1.54TLB
133.244+ 1.54BTB
30.580 471.493 4964.958
Min Fy 30777 2104 1.15DL
29837
+ 1.2SIDL
-2037.05
+ 1.4CL-1083.793
+ 1.4PLB + -216.353
1.54TLB - 1.54BTB
-34.189 -789.038 -3223.962
Max Fz 30777 3154 1.15DL
29837
+ 1.2SIDL
9979.461
+ 0.42CL 262.175
+ 0.42PLA +974.395
0.462TLA - 11.947
0.462BTA2801.363
- 0.3SLX - 0.3SLY
872.068
- 1SLZ - 1.54NLA
Min Fz 30777 3178 1.15DL
29833
+ 1.2SIDL
-1944.53
+ 0.42CL-187.468
+ 0.42PLB +-958.754
0.462TLB-13.164
- 0.462BTB
-3910.776
- 0.3SLX - 0.3SLY
-701.033
- 1SLZ - 1.54NLB
Max Mx 30777 2104 1.15DL
29833
+ 1.2SIDL
10813.11
+ 1.4CL 1126.973
+ 1.4PLB + 1.54TLB
233.905- 1.54BTB
33.590 841.416 4642.163
Min Mx 30777 2103 1.15DL
29837
+ 1.2SIDL
-1551.81
+ 1.4CL-1007.596
+ 1.4PLB + -217.624
1.54TLB + 1.54BTB
-34.738 -788.37 -3010.228
Max My 30777 3147 1.15DL
29833
+ 1.2SIDL
10034.35
+ 0.42CL 284.926
+ 0.42PLA +957.965
0.462TLA +13.312
0.462BTA
3805.659
+ 0.3SLX + 0.3SLY
1217.65+ 1SLZ + 1.54NLA
Min My 30777 3154 1.15DL
29833
+ 1.2SIDL
-1930.93
+ 0.42CL-187.192
+ 0.42PLA +-940.287
0.462TLA --14.381
0.462BTA
-3999.171
- 0.3SLX - 0.3SLY
-700.274
- 1SLZ - 1.54NLA
Max Mz 30901 2103 1.15DL
29957
+ 1.2SIDL
10608.69
+ 1.4CL 1210.666
+ 1.4PLB + 1.54TLB
133.244+ 1.54BTB
30.580 471.493 4964.958
Min Mz 30777 2104 1.15DL
29837
+ 1.2SIDL
-2037.05
+ 1.4CL-1083.793
+ 1.4PLB + -216.353
1.54TLB - 1.54BTB
-34.189 -789.038 -3223.962
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

LC 1001-1190, 2031-2078, 3031-3078, 4001-


b) ODE Seismic
4032, 5009-5024 & 6009-6024
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30898 1102 1DL 29958
+ 1SIDL +8268.794
0.3CL + 0.3PLA
183.99
+ 0.3PLB724.366
+ 0.33TLA + 0.33TLB
9.336 - 0.33BTA
2366.966- 0.33BTB
527.725
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 30774 1015 1DL 29834
+ 1SIDL +-1802.72
0.3SLX + 0.3SLY
-161.938
+ 1SLZ -777.127 -10.739 -2236.078 -537.272
Max Fy 30898 1079 1DL 29954
+ 1SIDL +7655.332
0.3CL + 0.3PLA
613.05
+ 0.3PLB264.614
+ 0.33TLA + 17.860
0.33TLB + 1294.499
0.33BTA + 0.33BTB
2438.097
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30774 1086 1DL 29830
+ 1SIDL + 0.3CL
-946.59
+ 0.3PLA
-571.355
+ 0.3PLB -351.57
+ 0.33TLA +-20.279
0.33TLB - -1256.372
0.33BTA - 0.33BTB
-2354.315
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30774 3054 1DL 29834
+ 1SIDL +8047.719
0.3CL + 0.3PLA
190.108
+ 0.33TLA753.714
- 0.33BTA 9.153
- 0.3SLX2391.254
- 0.3SLY - 1SLZ548.548
- 1.1NLA
Min Fz 30774 3078 1DL 29830
+ 1SIDL +-1418.43
0.3CL + 0.3PLB
-167.907
+ 0.33TLB-784.85
- 0.33BTB
-10.318
- 0.3SLX-2942.551
- 0.3SLY - 1SLZ
-723.147
- 1.1NLB
Max Mx 30774 3031 1DL 29830
+ 1SIDL +7736.359
0.3CL + 0.3PLA
601.972
+ 0.33TLA315.153
+ 0.33BTA 19.589
+ 1SLX 1494.407
+ 0.3SLY + 0.3SLZ
2397.584
+ 1.1NLA
Min Mx 30774 3055 1DL 29834
+ 1SIDL +-1307.87
0.3CL + 0.3PLB
-547.057
+ 0.33TLB
-348.474
+ 0.33BTB
-20.813
+ 1SLX +-943.695
0.3SLY + 0.3SLZ
-1713.514
+ 1.1NLB
Max My 30774 3047 1DL 29830
+ 1SIDL +8007.645
0.3CL + 0.3PLA
206.362
+ 0.33TLA741.982
+ 0.33BTA 10.071
+ 0.3SLX3208.58
+ 0.3SLY + 1SLZ
798.034
+ 1.1NLA
Min My 30774 3054 1DL 29830
+ 1SIDL +-1428.28
0.3CL + 0.3PLA
-167.709
+ 0.33TLA
-771.658
- 0.33BTA-11.161
- 0.3SLX-3005.694
- 0.3SLY - 1SLZ
-722.602
- 1.1NLA
Max Mz 30898 1079 1DL 29954
+ 1SIDL +7655.332
0.3CL + 0.3PLA
613.05
+ 0.3PLB264.614
+ 0.33TLA + 17.860
0.33TLB + 1294.499
0.33BTA + 0.33BTB
2438.097
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30774 1086 1DL 29830
+ 1SIDL + 0.3CL
-946.59
+ 0.3PLA
-571.355
+ 0.3PLB -351.57
+ 0.33TLA +-20.279
0.33TLB - -1256.372
0.33BTA - 0.33BTB
-2354.315
- 1SLX - 0.3SLY - 0.3SLZ
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30899 1095 1DL 29955
+ 1SIDL +8499.962
0.3CL + 0.3PLA
248.328
+ 0.3PLB720.434
+ 0.33TLA + 0.33TLB
9.918 + 3132.103
0.33BTA + 0.33BTB
1080.83
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 30775 1015 1DL 29835
+ 1SIDL +-1422.03
0.3SLX + 0.3SLY
-149.047
+ 1SLZ -775.872 -11.324 -2223.731 -429.525
Max Fy 30899 1079 1DL 29955
+ 1SIDL +7834.487
0.3CL + 0.3PLA
638.852
+ 0.3PLB260.591
+ 0.33TLA + 18.151
0.33TLB + 1271.054
0.33BTA + 0.33BTB
2646.831
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30775 1086 1DL 29831
+ 1SIDL +-187.897
0.3CL + 0.3PLA
-549.219
+ 0.3PLB-346.282
+ 0.33TLA +-20.644
0.33TLB - -1214.742
0.33BTA - 0.33BTB
-2168.644
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30775 3054 1DL 29835
+ 1SIDL +8016.104
0.3CL + 0.3PLA
218.835
+ 0.33TLA752.131
- 0.33BTA 9.745
- 0.3SLX2381.207
- 0.3SLY - 1SLZ741.317
- 1.1NLA
Min Fz 30775 3078 1DL 29831
+ 1SIDL +-1124.09
0.3CL + 0.3PLB
-152.549
+ 0.33TLB
-783.442
- 0.33BTB
-10.890
- 0.3SLX-2929.722
- 0.3SLY - 1SLZ
-584.242
- 1.1NLB
Max Mx 30775 3031 1DL 29831
+ 1SIDL + 7347.75
0.3CL + 0.3PLA
625.301
+ 0.33TLA309.531
+ 0.33BTA 19.983
+ 1SLX 1455.448
+ 0.3SLY + 0.3SLZ
2585.654
+ 1.1NLA
Min Mx 30775 3055 1DL 29835
+ 1SIDL +-229.298
0.3CL + 0.3PLB
-526.269
+ 0.33TLB
-343.692
+ 0.33BTB
-21.183
+ 1SLX +-903.554
0.3SLY + 0.3SLZ
-1559.109
+ 1.1NLB
Max My 30775 3047 1DL 29831
+ 1SIDL +8188.286
0.3CL + 0.3PLA
235.276
+ 0.33TLA740.069
+ 0.33BTA 10.686
+ 0.3SLX 3199.814
+ 0.3SLY + 1SLZ
1023.051
+ 1.1NLA
Min My 30775 3054 1DL 29831
+ 1SIDL +-1130.74
0.3CL + 0.3PLA
-152.262
+ 0.33TLA
-770.255
- 0.33BTA-11.760
- 0.3SLX-2992.825
- 0.3SLY - 1SLZ
-582.947
- 1.1NLA
Max Mz 30899 1079 1DL 29955
+ 1SIDL +7834.487
0.3CL + 0.3PLA
638.852
+ 0.3PLB260.591
+ 0.33TLA + 18.151
0.33TLB + 1271.054
0.33BTA + 0.33BTB
2646.831
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30775 1086 1DL 29831
+ 1SIDL +-187.897
0.3CL + 0.3PLA
-549.219
+ 0.3PLB-346.282
+ 0.33TLA +-20.644
0.33TLB - -1214.742
0.33BTA - 0.33BTB
-2168.644
- 1SLX - 0.3SLY - 0.3SLZ
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30900 1102 1DL 29960
+ 1SIDL +8208.384
0.3CL + 0.3PLA
190.968
+ 0.3PLB747.654
+ 0.33TLA + 0.33TLB
9.098 - 0.33BTA
2186.656- 0.33BTB564.783
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 30776 1015 1DL 29836
+ 1SIDL +-1679.27
0.3SLX + 0.3SLY
-168.565
+ 1SLZ -756.265 -10.413 -2363.789 -570.48
Max Fy 30900 1079 1DL 29956
+ 1SIDL +7313.711
0.3CL + 0.3PLA
614.857
+ 0.3PLB284.725
+ 0.33TLA + 17.022
0.33TLB + 1074.063
0.33BTA + 0.33BTB
2449.581+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30776 1086 1DL 29832
+ 1SIDL +-248.475
0.3CL + 0.3PLA
-572.426
+ 0.3PLB-322.986
+ 0.33TLA +-19.313
0.33TLB - 0.33BTA
-1404.29- 0.33BTB
-2359.445
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30776 3054 1DL 29836
+ 1SIDL +7869.541
0.3CL + 0.3PLA
196.833
+ 0.33TLA774.044
- 0.33BTA 8.928
- 0.3SLX2221.452
- 0.3SLY - 1SLZ582.462
- 1.1NLA
Min Fz 30776 3078 1DL 29832
+ 1SIDL +-1301.56
0.3CL + 0.3PLB
-174.579
+ 0.33TLB
-761.322
- 0.33BTB
-10.002
- 0.3SLX-3109.842
- 0.3SLY - 1SLZ
-765.374
- 1.1NLB
Max Mx 30776 3031 1DL 29832
+ 1SIDL +6859.997
0.3CL + 0.3PLA
603.317
+ 0.33TLA331.426
+ 0.33BTA 18.733
+ 1SLX 1273.482
+ 0.3SLY + 0.3SLZ
2404.943
+ 1.1NLA
Min Mx 30776 3055 1DL 29836
+ 1SIDL + 0.3CL
-520.12
+ 0.3PLB
-548.312
+ 0.33TLB-321.56
+ 0.33BTB
-19.799
+ 1SLX -1061.633
+ 0.3SLY + 0.3SLZ
-1718.296
+ 1.1NLB
Max My 30776 3047 1DL 29832
+ 1SIDL +7696.488
0.3CL + 0.3PLA
213.277
+ 0.33TLA761.979
+ 0.33BTA9.878
+ 0.3SLX 3017.969
+ 0.3SLY + 1SLZ
842.219
+ 1.1NLA
Min My 30776 3054 1DL 29832
+ 1SIDL +-1295.02
0.3CL + 0.3PLA
-174.292
+ 0.33TLA
-748.136
- 0.33BTA-10.844
- 0.3SLX-3172.941
- 0.3SLY - 1SLZ
-764.076
- 1.1NLA
Max Mz 30900 1079 1DL 29956
+ 1SIDL +7313.711
0.3CL + 0.3PLA
614.857
+ 0.3PLB284.725
+ 0.33TLA + 17.022
0.33TLB + 1074.063
0.33BTA + 0.33BTB
2449.581+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30900 1086 1DL 29956
+ 1SIDL +-339.204
0.3CL + 0.3PLA
-572.401
+ 0.3PLB-275.516
+ 0.33TLA +-17.795
0.33TLB - -1207.915
0.33BTA - 0.33BTB
-2362.792
- 1SLX - 0.3SLY - 0.3SLZ
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30777 1095 1DL 29833
+ 1SIDL +8465.133
0.3CL + 0.3PLA
237.944
+ 0.3PLB767.856
+ 0.33TLA + 0.33TLB
9.933 + 3013.887
0.33BTA + 0.33BTB1019.2
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 30777 1015 1DL 29837
+ 1SIDL +-1624.61
0.3SLX + 0.3SLY
-142.428
+ 1SLZ -757.52 -11.001 -2376.132 -396.414
Max Fy 30901 1079 1DL 29957
+ 1SIDL +8030.367
0.3CL + 0.3PLA
637.052
+ 0.3PLB288.743
+ 0.33TLA + 17.316
0.33TLB + 1097.438
0.33BTA + 0.33BTB
2635.496
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30777 1086 1DL 29833
+ 1SIDL +-944.309
0.3CL + 0.3PLA
-548.152
+ 0.3PLB-328.272
+ 0.33TLA +-19.680
0.33TLB - -1445.902
0.33BTA - 0.33BTB
-2163.576
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30777 3054 1DL 29837
+ 1SIDL + 8163.96
0.3CL + 0.3PLA
212.117
+ 0.33TLA775.627
- 0.33BTA 9.522
- 0.3SLX2231.497
- 0.3SLY - 1SLZ707.502
- 1.1NLA
Min Fz 30777 3078 1DL 29833
+ 1SIDL +-1333.24
0.3CL + 0.3PLB
-145.882
+ 0.33TLB
-762.729
- 0.33BTB
-10.577
- 0.3SLX-3122.668
- 0.3SLY - 1SLZ
-542.116
- 1.1NLB
Max Mx 30777 3031 1DL 29833
+ 1SIDL +7925.917
0.3CL + 0.3PLA
623.961
+ 0.33TLA337.046
+ 0.33BTA 19.128
+ 1SLX 1312.424
+ 0.3SLY + 0.3SLZ
2578.358
+ 1.1NLA
Min Mx 30777 3055 1DL 29837
+ 1SIDL +-896.073
0.3CL + 0.3PLB
-525.019
+ 0.33TLB
-326.341
+ 0.33BTB
-20.170
+ 1SLX -1101.756
+ 0.3SLY + 0.3SLZ
-1554.386
+ 1.1NLB
Max My 30777 3047 1DL 29833
+ 1SIDL +8203.165
0.3CL + 0.3PLA
228.368
+ 0.33TLA763.891
+ 0.33BTA 10.497
+ 0.3SLX 3026.732
+ 0.3SLY + 1SLZ
978.968
+ 1.1NLA
Min My 30777 3054 1DL 29833
+ 1SIDL +-1323.53
0.3CL + 0.3PLA
-145.685
+ 0.33TLA
-749.538
- 0.33BTA-11.447
- 0.3SLX-3185.807
- 0.3SLY - 1SLZ
-541.575
- 1.1NLA
Max Mz 30901 1079 1DL 29957
+ 1SIDL +8030.367
0.3CL + 0.3PLA
637.052
+ 0.3PLB288.743
+ 0.33TLA + 17.316
0.33TLB + 1097.438
0.33BTA + 0.33BTB
2635.496
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30777 1086 1DL 29833
+ 1SIDL +-944.309
0.3CL + 0.3PLA
-548.152
+ 0.3PLB-328.272
+ 0.33TLA +-19.680
0.33TLB - -1445.902
0.33BTA - 0.33BTB
-2163.576
- 1SLX - 0.3SLY - 0.3SLZ

c) Static LC 1001-1006
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30774 1006 1DL 29830
+ 1SIDL +4884.759
1CL + 1PLA +-29.052
1PLB + 1.1TLA
-18.679
+ 1.1TLB --0.655
1.1BTA - 1.1BTB
145.544 -159.967
Min Fx 30898 1003 1DL 29954
+ 1SIDL + 3695.82
1CL + 1PLB + 56.912
1.1TLB + -27.876
1.1BTB -0.731 187.068 180.21
Max Fy 30898 1005 1DL 29954
+ 1SIDL +4136.195
1CL + 1PLA + 1PLB
84.87
+ 1.1TLA
-27.529
+ 1.1TLB +-0.590
1.1BTA + 174.131
1.1BTB 279.765
Min Fy 30774 1006 1DL 29830
+ 1SIDL +4884.759
1CL + 1PLA +-29.052
1PLB + 1.1TLA
-18.679
+ 1.1TLB --0.655
1.1BTA - 1.1BTB
145.544 -159.967
Max Fz 30774 1002 1DL 29830
+ 1SIDL +4276.629
1CL + 1PLA + -2.468
1.1TLA - 1.1BTA
-12.57 -0.616 93.141 -53.942
Min Fz 30898 1003 1DL 29954
+ 1SIDL + 3695.82
1CL + 1PLB + 56.912
1.1TLB + -27.876
1.1BTB -0.731 187.068 180.21
Max Mx 30898 1001 1DL 29954
+ 1SIDL +3866.435
1CL + 1PLA + 57.464
1.1TLA + -19.163
1.1BTA -0.184 115.176 180.861
Min Mx 30774 1003 1DL 29830
+ 1SIDL + 3773.78
1CL + 1PLB + 51.726
1.1TLB + -24.721
1.1BTB -1.060 175.409 153.844
Max My 30898 1003 1DL 29954
+ 1SIDL + 3695.82
1CL + 1PLB + 56.912
1.1TLB + -27.876
1.1BTB -0.731 187.068 180.21
Min My 30774 1002 1DL 29834
+ 1SIDL +4276.629
1CL + 1PLA + -2.468
1.1TLA - 1.1BTA
-12.57 -0.616 80.57 -51.474
Max Mz 30898 1005 1DL 29954
+ 1SIDL +4136.195
1CL + 1PLA + 1PLB
84.87
+ 1.1TLA
-27.529
+ 1.1TLB +-0.590
1.1BTA + 174.131
1.1BTB 279.765
Min Mz 30774 1006 1DL 29830
+ 1SIDL +4884.759
1CL + 1PLA +-29.052
1PLB + 1.1TLA
-18.679
+ 1.1TLB --0.655
1.1BTA - 1.1BTB
145.544 -159.967
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30775 1005 1DL 29831
+ 1SIDL +5218.422
1CL + 1PLA + 111.81
1PLB + 1.1TLA
-27.341
+ 1.1TLB +-0.830
1.1BTA + 181.146
1.1BTB 516.536
Min Fx 30899 1004 1DL 29955
+ 1SIDL + 3972.17
1CL + 1PLB + 28.262
1.1TLB - 1.1BTB
-25.328 -0.282 177.873 188.031
Max Fy 30899 1005 1DL 29955
+ 1SIDL +5139.809
1CL + 1PLA +116.062
1PLB + 1.1TLA
-28.861
+ 1.1TLB +-0.564
1.1BTA + 184.935
1.1BTB 536.173
Min Fy 30775 1006 1DL 29831
+ 1SIDL +4463.387
1CL + 1PLA + 1PLB
2.679
+ 1.1TLA
-17.841
+ 1.1TLB --0.650
1.1BTA - 1.1BTB
138.674 100.889
Max Fz 30775 1002 1DL 29831
+ 1SIDL +4212.753
1CL + 1PLA + 25.845
1.1TLA - -12.311
1.1BTA -0.618 90.997 178.819
Min Fz 30899 1005 1DL 29955
+ 1SIDL +5139.809
1CL + 1PLA +116.062
1PLB + 1.1TLA
-28.861
+ 1.1TLB +-0.564
1.1BTA + 184.935
1.1BTB 536.173
Max Mx 30899 1001 1DL 29955
+ 1SIDL +4516.576
1CL + 1PLA + 85.184
1.1TLA + -19.966
1.1BTA -0.172 121.673 408.735
Min Mx 30775 1003 1DL 29831
+ 1SIDL +4415.913
1CL + 1PLB + 79.228
1.1TLB + -25.561
1.1BTB -1.037 182.225 379.917
Max My 30899 1003 1DL 29955
+ 1SIDL +4338.941
1CL + 1PLB + 83.758
1.1TLB + -28.672
1.1BTB -0.701 193.512 400.884
Min My 30775 1002 1DL 29835
+ 1SIDL +4212.753
1CL + 1PLA + 25.845
1.1TLA - -12.311
1.1BTA -0.618 78.686 152.973
Max Mz 30899 1005 1DL 29955
+ 1SIDL +5139.809
1CL + 1PLA +116.062
1PLB + 1.1TLA
-28.861
+ 1.1TLB +-0.564
1.1BTA + 184.935
1.1BTB 536.173
Min Mz 30775 1006 1DL 29835
+ 1SIDL +4463.387
1CL + 1PLA + 1PLB
2.679
+ 1.1TLA
-17.841
+ 1.1TLB --0.650
1.1BTA - 1.1BTB
120.833 98.21
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30776 1006 1DL 29832
+ 1SIDL +4884.015
1CL + 1PLA +-29.073
1PLB + 1.1TLA
13.912
+ 1.1TLB --0.682
1.1BTA - 1.1BTB
-122.36 -160.145
Min Fx 30900 1001 1DL 29956
+ 1SIDL +3595.392
1CL + 1PLA + 58.027
1.1TLA + 1.1BTA
7.191 -0.038 -101.582 185.481
Max Fy 30900 1005 1DL 29956
+ 1SIDL +4015.361
1CL + 1PLA + 85.024
1PLB + 1.1TLA
2.177
+ 1.1TLB +-0.384
1.1BTA + 1.1BTB
-70.221 281.019
Min Fy 30776 1006 1DL 29832
+ 1SIDL +4884.015
1CL + 1PLA +-29.073
1PLB + 1.1TLA
13.912
+ 1.1TLB --0.682
1.1BTA - 1.1BTB
-122.36 -160.145
Max Fz 30776 1002 1DL 29832
+ 1SIDL +4093.257
1CL + 1PLA + -2.034
1.1TLA - 1.1BTA
15.568 -0.592 -138.192 -50.37
Min Fz 30900 1003 1DL 29956
+ 1SIDL +3777.734
1CL + 1PLB + 56.584
1.1TLB + 1.1BTB
-1.498 -0.587 -29.887 177.487
Max Mx 30900 1001 1DL 29956
+ 1SIDL +3595.392
1CL + 1PLA + 58.027
1.1TLA + 1.1BTA
7.191 -0.038 -101.582 185.481
Min Mx 30776 1003 1DL 29832
+ 1SIDL +3888.059
1CL + 1PLB + 51.357
1.1TLB + 1.1BTB
2.31 -0.926 -46.902 150.791
Max My 30900 1003 1DL 29956
+ 1SIDL +3777.734
1CL + 1PLB + 56.584
1.1TLB + 1.1BTB
-1.498 -0.587 -29.887 177.487
Min My 30776 1002 1DL 29832
+ 1SIDL +4093.257
1CL + 1PLA + -2.034
1.1TLA - 1.1BTA
15.568 -0.592 -138.192 -50.37
Max Mz 30900 1005 1DL 29956
+ 1SIDL +4015.361
1CL + 1PLA + 85.024
1PLB + 1.1TLA
2.177
+ 1.1TLB +-0.384
1.1BTA + 1.1BTB
-70.221 281.019
Min Mz 30776 1006 1DL 29832
+ 1SIDL +4884.015
1CL + 1PLA +-29.073
1PLB + 1.1TLA
13.912
+ 1.1TLB --0.682
1.1BTA - 1.1BTB
-122.36 -160.145
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30777 1005 1DL 29833
+ 1SIDL +5126.657
1CL + 1PLA +111.704
1PLB + 1.1TLA
5.767
+ 1.1TLB +-0.633
1.1BTA + 1.1BTB
-90.888 515.678
Min Fx 30901 1002 1DL 29957
+ 1SIDL +3925.724
1CL + 1PLA + 28.993
1.1TLA - 1.1BTA
13.699 -0.447 -128.726 191.004
Max Fy 30901 1005 1DL 29957
+ 1SIDL +5018.975
1CL + 1PLA +115.907
1PLB + 1.1TLA
3.509
+ 1.1TLB +-0.358
1.1BTA + 1.1BTB
-81.024 534.92
Min Fy 30777 1006 1DL 29833
+ 1SIDL +4462.643
1CL + 1PLA + 1PLB
2.701
+ 1.1TLA
13.074
+ 1.1TLB --0.677
1.1BTA - 1.1BTB
-115.49 101.067
Max Fz 30777 1002 1DL 29833
+ 1SIDL +4029.381
1CL + 1PLA + 25.411
1.1TLA - 1.1BTA
15.309 -0.595 -136.048 175.247
Min Fz 30901 1003 1DL 29957
+ 1SIDL +4420.855
1CL + 1PLB + 84.087
1.1TLB + 1.1BTB
-0.702 -0.557 -36.331 403.609
Max Mx 30901 1001 1DL 29957
+ 1SIDL +4245.533
1CL + 1PLA + 84.621
1.1TLA + 1.1BTA
7.994 -0.025 -108.078 404.115
Min Mx 30777 1003 1DL 29833
+ 1SIDL +4530.192
1CL + 1PLB + 79.598
1.1TLB + 1.1BTB
3.15 -0.903 -53.718 382.97
Max My 30901 1003 1DL 29957
+ 1SIDL +4420.855
1CL + 1PLB + 84.087
1.1TLB + 1.1BTB
-0.702 -0.557 -36.331 403.609
Min My 30777 1002 1DL 29833
+ 1SIDL +4029.381
1CL + 1PLA + 25.411
1.1TLA - 1.1BTA
15.309 -0.595 -136.048 175.247
Max Mz 30901 1005 1DL 29957
+ 1SIDL +5018.975
1CL + 1PLA +115.907
1PLB + 1.1TLA
3.509
+ 1.1TLB +-0.358
1.1BTA + 1.1BTB
-81.024 534.92
Min Mz 30777 1006 1DL 29837
+ 1SIDL +4462.643
1CL + 1PLA + 1PLB
2.701
+ 1.1TLA
13.074
+ 1.1TLB --0.677
1.1BTA - -102.416
1.1BTB 98.366

2.2 Pile Loads

MDE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 10962 10407 10067 11298


Min Fx -2557 -2102 -2398 -2352
Max Fy 9824 10094 9226 10609
Min Fy -1916 -605 -461 -2037
Max Fz 9864 9789 9644 9979
Min Fz -2019 -1684 -1869 -1945
Max Mx 10962 9358 9530 10813
Min Mx -2404 -99 -971 -1552
Max My 9808 10030 9402 10034
Min My -2033 -1694 -1860 -1931
Max Mz 9824 10094 9226 10609
Min Mz -1916 -605 -461 -2037
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

ODE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 8269 8500 8208 8465


Min Fx -1803 -1422 -1679 -1625
Max Fy 7655 7834 7314 8030
Min Fy -947 -188 -248 -944
Max Fz 8048 8016 7870 8164
Min Fz -1418 -1124 -1302 -1333
Max Mx 7736 7348 6860 7926
Min Mx -1308 -229 -520 -896
Max My 8008 8188 7696 8203
Min My -1428 -1131 -1295 -1324
Max Mz 7655 7834 7314 8030
Min Mz -947 -188 -339 -944

Static
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 4885 5218 4884 5127


Min Fx 3696 3972 3595 3926
Max Fy 4136 5140 4015 5019
Min Fy 4885 4463 4884 4463
Max Fz 4277 4213 4093 4029
Min Fz 3696 5140 3778 4421
Max Mx 3866 4517 3595 4246
Min Mx 3774 4416 3888 4530
Max My 3696 4339 3778 4421
Min My 4277 4213 4093 4029
Max Mz 4136 5140 4015 5019
Min Mz 4885 4463 4884 4463

3.1 Moment at Bottom Face:

Lever arm Z = Pile Centre to column face

Z = 0.80 m

Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or


2.0 m (P1+P2)xZ or (P3+P4)xZ, whichever
column is maximum

P kN
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = 510.276 kN.m
Design Moment, M = M1 - M2

Case M1 (kN.m) M = (M1 - M2) (kN.m)


MDE Seismic 17364.000 16777.182
ODE Seismic 13572.000 13061.724
Static 8276.000 7765.724

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
2
K = Mu/bd fcu = 0.022 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1710.50 mm
Hence, z = 0.95 d = 1624.98 mm
As = Mu / (fy z)
Ast = 26473.279 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


29 120 0 0 0 0

= 28716.101 mm2 OK

3.2 Moment at Top Face:

Lever arm Z = Pile Centre to column face

P kN Z = 0.80 m
2.0 m
column Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or
(P1+P2)xZ or (P3+P4)xZ, whichever
is minimum

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = -510.276 kN.m
Design Moment, M = M1 + M2

Case M1 (kN.m) M = (M1 + M2) (kN.m)


MDE Seismic -3964.000 -4550.818
ODE Seismic -2785.600 -3295.876
Static 0.000 0.000

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

K = Mu/bd2fcu = 0.006 K'


Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.95 d = 1626.88 mm
As = M u / (f y z)
Ast = 7172.501 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 120 0 0 0 0

= 21357.103 mm2 OK

3.3 Moment Capacity, Stress and Crack Width Check from Oasys

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 16780 23490 0.7142 OK
Minima
2 0.0 4551 23490 0.1937 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
26.48 OK
26.48 OK
Minima
-137.9 OK
-137.9 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fcu 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Oasys Results
Cocncrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
3 2.555 OK 3 14.25 OK
3 2.555 OK 3 14.25 OK
Minima Minima
3 -0.5803 OK 3 -51.85 OK
3 -0.5803 OK 3 -51.85 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.097 mm OK

3.4 Minimum Reinforcement


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4007.25 mm2/m
2
At bottom face, Provided = 5418 mm2/m
Astprovided > Astmin OK
At top face, Provided = 4030 mm2/m
Astprovided > Astmin OK

4.0 Shear Check


Total pile reaction, V1 = 21705 kN
As per Cl. 3.11.4.3, pg. 82, BS 8110-1: 1997, critical section for shear should be located 20% of the pile diameter inside
Distance of critical section for shear check from column face = 0.440 m
Factored weight per unit length due to soil and pile cap = 431.087 kN/m
Hence, downward reaction due to soil and pile cap weight,
V2 = weight per unit length x (length of pile cap - 0.5 x column size - distance of critical section)
V2 = 522 kN
Net reaction, Vu = V1 - V2 = 21183 kN
Width of pile cap available b = 5.300 m
Effective depth of pile cap d = 1.711 m
Area of tensile steel provided As = 28716 mm2
= 0.029 m2
Percentage of tensile steel provided 100As/(b.d) = 0.317 %
Shear stress = Vu /(b.d) = 2336.66 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.35 MPa
= 350 kN/sqm
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

As per Cl. 3.11.4.4, pg. 82, BS 8110-1:1997,


Enhanced shear strength of concrete, say vc,1 = 2.d.vc /av
av = 0.440 m
Therefore, vc,1 = 2.72 MPa
= 2721 kN/sqm
Vus = Vu - vc,1 b d = -3486.52 kN

Requirement of shear reinforcement = Not Required

5.0 Check for punching shear


Total pile load = 42734 kN
From section 1.0 above, factored weight of pile cap + earthfill = 1987 kN
Hence, net punching shear force = 40747 kN
Effective depth of pile cap = 1.711 m
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, punching shear shall be checked at the perimeter of the column.
Shear perimeter = 8.000 m
Shearing Area = 13.684 m2
Punching Shear stress = 2977.729 kN/m2
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997,
Allowable punching shear stress = lesser of 0.8 fcu or 5 N/mm2 = 5.00 N/mm2
= 5000.000 kN/m2
OK
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, since the pile spacing is not greater than 3 times the pile diameter, no
additional punching shear check is required.
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR COLUMN C24, C26, C28 & C30


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Column No. = C24, C26, C28 & C30

No. of piles n = 4
Dia of pile = 1.20 m
Size of Column = 2.00 m x 2.00 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 5.30 m x 5.30 m


2
Area of pile cap = 28.09 m
Depth of pile cap D = 1.80 m
Volume of pile cap = 50.56 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 1264.05 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 36.14 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 722.70 kN

Total weight of (Pile cap + Earthfill) = 1986.75 kN

2.0 PILE LOADS

2.1 Summary of Staad Results (Forces at Bottom of Pile Cap)---

LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-


a) MDE Seismic
2378, 3131-3178,4101-4132, 5109-5124 & 6109-6124
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31022 2104 1.15DL
30078
+ 1.2SIDL
9933.722
+ 1.4CL 1103.682
+ 1.4PLB + 1.54TLB
58.906- 1.54BTB
25.268 435.626 4434.859
Min Fx 31022 2103 1.15DL
30082
+ 1.2SIDL
-2554.29
+ 1.4CL-1036.768
+ 1.4PLB + -100.563
1.54TLB + 1.54BTB
-25.910 -100.174 -3218.445
Max Fy 31146 2103 1.15DL
30202
+ 1.2SIDL
8889.21
+ 1.4CL 1193.345
+ 1.4PLB + 1.54TLB
61.359+ 1.54BTB
17.327 456.417 4782.691
Min Fy 31270 2104 1.15DL
30330
+ 1.2SIDL
-1340.06
+ 1.4CL-1140.347
+ 1.4PLB + -110.746
1.54TLB - 1.54BTB
-18.274 -149.51 -3531.795
Max Fz 31270 3154 1.15DL
30330
+ 1.2SIDL
9487.612
+ 0.42CL 240.552
+ 0.42PLA +933.303
0.462TLA - 8.313
0.462BTA2968.099
- 0.3SLX - 0.3SLY
699.531
- 1SLZ - 1.54NLA
Min Fz 31270 3178 1.15DL
30326
+ 1.2SIDL
-1831.31
+ 0.42CL-226.968
+ 0.42PLB +-970.161
0.462TLB-10.977
- 0.462BTB-3679.393
- 0.3SLX - 0.3SLY
-980.541
- 1SLZ - 1.54NLB
Max Mx 31022 2104 1.15DL
30078
+ 1.2SIDL
9933.722
+ 1.4CL 1103.682
+ 1.4PLB + 1.54TLB
58.906- 1.54BTB
25.268 435.626 4434.859
Min Mx 31022 2103 1.15DL
30082
+ 1.2SIDL
-2554.29
+ 1.4CL-1036.768
+ 1.4PLB + -100.563
1.54TLB + 1.54BTB
-25.910 -100.174 -3218.445
Max My 31270 2171 1.15DL
30326
+ 1.2SIDL
9313.995
+ 0.42CL 264.132
+ 0.42PLB +923.527
0.462TLB +8.180
0.462BTB
3973.543
+ 0.3SLX + 1029.072
0.3SLY + 1SLZ
Min My 31270 3154 1.15DL
30326
+ 1.2SIDL
-1845.15
+ 0.42CL-226.246
+ 0.42PLA +-954.431
0.462TLA - -9.894
0.462BTA-3754.389
- 0.3SLX - 0.3SLY
-977.73
- 1SLZ - 1.54NLA
Max Mz 31146 2103 1.15DL
30202
+ 1.2SIDL
8889.21
+ 1.4CL 1193.345
+ 1.4PLB + 1.54TLB
61.359+ 1.54BTB
17.327 456.417 4782.691
Min Mz 31270 2104 1.15DL
30330
+ 1.2SIDL
-1340.06
+ 1.4CL-1140.347
+ 1.4PLB + -110.746
1.54TLB - 1.54BTB
-18.274 -149.51 -3531.795
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31395 2103 1.15DL
30451
+ 1.2SIDL
10422.19
+ 1.4CL 1207.954
+ 1.4PLB + 1.54TLB
86.222+ 1.54BTB
17.300 564.455 4941.091
Min Fx 31395 2104 1.15DL
30455
+ 1.2SIDL
-2218.04
+ 1.4CL-1109.148
+ 1.4PLB + -125.827
1.54TLB - 1.54BTB
-20.126 -223.119 -3328.413
Max Fy 31147 2103 1.15DL
30203
+ 1.2SIDL
10363.97
+ 1.4CL 1219.821
+ 1.4PLB + 1.54TLB
73.041+ 1.54BTB
17.302 571.581 5000.218
Min Fy 31271 2104 1.15DL
30331
+ 1.2SIDL
-2086.65
+ 1.4CL-1115.067
+ 1.4PLB + -123.322
1.54TLB - 1.54BTB
-18.215 -242.932 -3349.152
Max Fz 31271 3154 1.15DL
30331
+ 1.2SIDL
9849.024
+ 0.42CL 274.067
+ 0.42PLA +935.844
0.462TLA - 8.244
0.462BTA2988.512
- 0.3SLX - 0.3SLY
926.131
- 1SLZ - 1.54NLA
Min Fz 31271 3178 1.15DL
30327
+ 1.2SIDL
-1892.27
+ 0.42CL-209.812
+ 0.42PLB +-973.016
0.462TLB-10.884
- 0.462BTB-3700.143
- 0.3SLX - 0.3SLY
-826.332
- 1SLZ - 1.54NLB
Max Mx 31023 2104 1.15DL
30079
+ 1.2SIDL
9158.862
+ 1.4CL 1125.999
+ 1.4PLB + 1.54TLB
65.57- 1.54BTB
25.292 485.233 4618.317
Min Mx 31023 2103 1.15DL
30083
+ 1.2SIDL
-1018.09
+ 1.4CL-1008.529
+ 1.4PLB + -108.084
1.54TLB + 1.54BTB
-25.899 -137.773 -3014.559
Max My 31271 2171 1.15DL
30327
+ 1.2SIDL
9967.692
+ 0.42CL 297.416
+ 0.42PLB +925.625
0.462TLB +8.132
0.462BTB
4000.432
+ 0.3SLX + 1289.502
0.3SLY + 1SLZ
Min My 31271 3154 1.15DL
30327
+ 1.2SIDL
-1899.64
+ 0.42CL-208.984
+ 0.42PLA +-957.293
0.462TLA - -9.833
0.462BTA-3775.08
- 0.3SLX - 0.3SLY
-822.633
- 1SLZ - 1.54NLA
Max Mz 31147 2103 1.15DL
30203
+ 1.2SIDL
10363.97
+ 1.4CL 1219.821
+ 1.4PLB + 1.54TLB
73.041+ 1.54BTB
17.302 571.581 5000.218
Min Mz 31271 2104 1.15DL
30331
+ 1.2SIDL
-2086.65
+ 1.4CL-1115.067
+ 1.4PLB + -123.322
1.54TLB - 1.54BTB
-18.215 -242.932 -3349.152
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31024 2104 1.15DL
30080
+ 1.2SIDL
10153.89
+ 1.4CL 1103.792
+ 1.4PLB + 1.54TLB
92.743- 1.54BTB
23.589 292.145 4435.702
Min Fx 31024 2103 1.15DL
30084
+ 1.2SIDL
-2825.82
+ 1.4CL-1036.922
+ 1.4PLB + 1.54TLB
-84.656+ 1.54BTB
-24.042 -334.113 -3219.519
Max Fy 31148 2103 1.15DL
30204
+ 1.2SIDL
9443.413
+ 1.4CL 1194.123
+ 1.4PLB + 1.54TLB
98.965+ 1.54BTB
16.629 360.234 4788.955
Min Fy 31272 2104 1.15DL
30332
+ 1.2SIDL
-2155.11
+ 1.4CL-1141.152
+ 1.4PLB + 1.54TLB
-98.034- 1.54BTB
-18.564 -430.994 -3537.496
Max Fz 31272 3154 1.15DL
30332
+ 1.2SIDL
9635.188
+ 0.42CL 249.267
+ 0.42PLA +960.618
0.462TLA - 8.426
0.462BTA2804.663
- 0.3SLX - 0.3SLY
747.15
- 1SLZ - 1.54NLA
Min Fz 31272 3178 1.15DL
30328
+ 1.2SIDL
-2224.63
+ 0.42CL-235.235
+ 0.42PLB +-947.567
0.462TLB-11.011
- 0.462BTB-3903.716
- 0.3SLX - 0.3SLY
-1035.42
- 1SLZ - 1.54NLB
Max Mx 31024 2103 1.15DL
30080
+ 1.2SIDL
9588.057
+ 1.4CL +1182.43
1.4PLB + 1.54TLB
85.473+ 1.54BTB
23.596 326.138 4738.954
Min Mx 31024 2104 1.15DL
30084
+ 1.2SIDL
-2259.99
+ 1.4CL +-1115.56
1.4PLB + 1.54TLB
-77.386- 1.54BTB
-24.049 -360.836 -3444.132
Max My 31272 2171 1.15DL
30328
+ 1.2SIDL
9511.193
+ 0.42CL 272.637
+ 0.42PLB +950.379
0.462TLB +8.342
0.462BTB3791.29
+ 0.3SLX + 1085.879
0.3SLY + 1SLZ
Min My 31272 3154 1.15DL
30328
+ 1.2SIDL
-2215.47
+ 0.42CL-234.414
+ 0.42PLA +-931.837
0.462TLA - -9.926
0.462BTA-3978.708
- 0.3SLX - -1031.775
0.3SLY - 1SLZ - 1.54NLA
Max Mz 31272 2103 1.15DL
30328
+ 1.2SIDL
9524.929
+ 1.4CL 1194.082
+ 1.4PLB + 1.54TLB
108.666+ 1.54BTB
16.400 393.664 4789.656
Min Mz 31272 2104 1.15DL
30332
+ 1.2SIDL
-2155.11
+ 1.4CL-1141.152
+ 1.4PLB + 1.54TLB
-98.034- 1.54BTB
-18.564 -430.994 -3537.496
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31149 2195 1.15DL
30205
+ 1.2SIDL
9990.691
+ 0.42CL 303.204
+ 0.42PLA +936.797
0.42PLB + 0.462TLA
9.050 + 0.462TLB
3688.708 + 0.462BTA
1292.768+ 0.462BTB + 0.3SLX + 0.3S
Min Fx 31397 2115 1.15DL
30457
+ 1.2SIDL
-2122.92
+ 0.3SLX-196.115
+ 0.3SLY + 1SLZ
-910.816 -10.603 -2871.328 -569.764
Max Fy 31149 2103 1.15DL
30205
+ 1.2SIDL
9670.911
+ 1.4CL 1219.045
+ 1.4PLB + 1.54TLB
87.28+ 1.54BTB
16.624 245.005 4993.962
Min Fy 31273 2104 1.15DL
30333
+ 1.2SIDL
-1411.85
+ 1.4CL-1114.263
+ 1.4PLB + 1.54TLB
-85.441- 1.54BTB
-18.530 -337.271 -3343.458
Max Fz 31273 3154 1.15DL
30333
+ 1.2SIDL
9572.033
+ 0.42CL 265.367
+ 0.42PLA +958.072
0.462TLA - 8.366
0.462BTA2784.177
- 0.3SLX - 0.3SLY
878.706
- 1SLZ - 1.54NLA
Min Fz 31273 3178 1.15DL
30329
+ 1.2SIDL
-1861.01
+ 0.42CL-201.561
+ 0.42PLB +-944.707
0.462TLB-10.926
- 0.462BTB
-3882.894
- 0.3SLX - 0.3SLY
-771.657
- 1SLZ - 1.54NLB
Max Mx 31025 2103 1.15DL
30081
+ 1.2SIDL
9365.818
+ 1.4CL 1204.132
+ 1.4PLB + 1.54TLB
79.816+ 1.54BTB
23.641 256.396 4917.482
Min Mx 31025 2104 1.15DL
30085
+ 1.2SIDL
-1276.41
+ 1.4CL-1086.618
+ 1.4PLB + 1.54TLB
-70.872- 1.54BTB
-24.059 -304.547 -3235.251
Max My 31273 2171 1.15DL
30329
+ 1.2SIDL
9740.322
+ 0.42CL 288.927
+ 0.42PLB +948.276
0.462TLB +8.302
0.462BTB3764.33
+ 0.3SLX + 0.3SLY
1232.9+ 1SLZ
Min My 31273 3154 1.15DL
30329
+ 1.2SIDL
-1845.39
+ 0.42CL-200.831
+ 0.42PLA +-928.97
0.462TLA - -9.873
0.462BTA-3957.944
- 0.3SLX - 0.3SLY
-768.791
- 1SLZ - 1.54NLA
Max Mz 31149 2103 1.15DL
30205
+ 1.2SIDL
9670.911
+ 1.4CL 1219.045
+ 1.4PLB + 1.54TLB
87.28+ 1.54BTB
16.624 245.005 4993.962
Min Mz 31273 2104 1.15DL
30333
+ 1.2SIDL
-1411.85
+ 1.4CL-1114.263
+ 1.4PLB + 1.54TLB
-85.441- 1.54BTB
-18.530 -337.271 -3343.458
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

LC 1001-1190, 2031-2078, 3031-3078, 4001-


b) ODE Seismic
4032, 5009-5024 & 6009-6024
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31270 1102 1DL 30330
+ 1SIDL + 0.3CL
7977.2
+ 0.3PLA
184.633
+ 0.3PLB735.933
+ 0.33TLA + 0.33TLB
5.948 - 0.33BTA
2399.811- 0.33BTB532.902
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 31022 1015 1DL 30082
+ 1SIDL +-1624.76
0.3SLX + 0.3SLY
-161.852
+ 1SLZ -745.788 -8.696 -2139.177 -537.574
Max Fy 31270 1079 1DL 30326
+ 1SIDL +7148.529
0.3CL + 0.3PLA
621.836
+ 0.3PLB257.281
+ 0.33TLA + 0.33TLB
9.352 + 1218.756
0.33BTA + 0.33BTB
2481.761
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31270 1086 1DL 30326
+ 1SIDL +-437.363
0.3CL + 0.3PLA
-590.291
+ 0.3PLB-290.017
+ 0.33TLA +-11.314
0.33TLB - -1002.942
0.33BTA - 0.33BTB
-2445.443
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31270 3054 1DL 30330
+ 1SIDL +7770.338
0.3CL + 0.3PLA
193.76
+ 0.33TLA742.163
- 0.33BTA 6.534
- 0.3SLX2374.396
- 0.3SLY - 1SLZ561.245
- 1.1NLA
Min Fz 31270 3078 1DL 30326
+ 1SIDL +-1249.46
0.3CL + 0.3PLB
-178.795
+ 0.33TLB
-773.556
- 0.33BTB-8.749
- 0.3SLX-2929.832
- 0.3SLY - 1SLZ-776.452
- 1.1NLB
Max Mx 31022 2031 1DL 30078
+ 1SIDL +7400.977
0.3CL + 0.3PLA
606.308
+ 0.33TLA243.202
+ 0.33BTA 14.656
+ 1SLX +1138.973
0.3SLY + 0.3SLZ
2418.111
+ 1.1LLA
Min Mx 31022 3062 1DL 30078
+ 1SIDL +-1022.83
0.3CL + 0.3PLB
-564.968
+ 0.33TLB-279.12
- 0.33BTB
-14.870
- 1SLX - 0.3SLY
-909.602- 0.3SLZ
-2330.418
- 1.1NLB
Max My 31270 1071 1DL 30326
+ 1SIDL +7646.325
0.3CL + 0.3PLB
210.602
+ 0.33TLB735.181
+ 0.33BTB6.439
+ 0.3SLX3173.132
+ 0.3SLY + 1SLZ
818.364
Min My 31270 3054 1DL 30326
+ 1SIDL +-1259.34
0.3CL + 0.3PLA
-178.278
+ 0.33TLA-762.32
- 0.33BTA-7.975
- 0.3SLX-2983.401
- 0.3SLY - 1SLZ
-774.444
- 1.1NLA
Max Mz 31270 1079 1DL 30326
+ 1SIDL +7148.529
0.3CL + 0.3PLA
621.836
+ 0.3PLB257.281
+ 0.33TLA + 0.33TLB
9.352 + 1218.756
0.33BTA + 0.33BTB
2481.761
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31270 1086 1DL 30326
+ 1SIDL +-437.363
0.3CL + 0.3PLA
-590.291
+ 0.3PLB-290.017
+ 0.33TLA +-11.314
0.33TLB - -1002.942
0.33BTA - 0.33BTB
-2445.443
- 1SLX - 0.3SLY - 0.3SLZ
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31271 1095 1DL 30327
+ 1SIDL +8396.944
0.3CL + 0.3PLA
248.099
+ 0.3PLB737.326
+ 0.33TLA + 0.33TLB
6.557 + 0.33BTA
3190.34+ 0.33BTB
1077.332
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 31271 1015 1DL 30331
+ 1SIDL +-1442.36
0.3SLX + 0.3SLY
-157.986
+ 1SLZ -769.076 -8.067 -2240.859 -465.685
Max Fy 31271 1079 1DL 30327
+ 1SIDL +7968.573
0.3CL + 0.3PLA
646.644
+ 0.3PLB263.385
+ 0.33TLA + 0.33TLB
9.323 + 1278.867
0.33BTA + 0.33BTB
2682.466
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31271 1086 1DL 30327
+ 1SIDL +-746.996
0.3CL + 0.3PLA
-569.722
+ 0.3PLB-296.768
+ 0.33TLA +-11.262
0.33TLB - -1057.809
0.33BTA - 0.33BTB
-2273.122
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31271 3054 1DL 30331
+ 1SIDL +8087.241
0.3CL + 0.3PLA
221.858
+ 0.33TLA744.152
- 0.33BTA 6.480
- 0.3SLX2390.958
- 0.3SLY - 1SLZ751.855
- 1.1NLA
Min Fz 31271 3078 1DL 30327
+ 1SIDL +-1269.26
0.3CL + 0.3PLB
-163.71
+ 0.33TLB
-775.873
- 0.33BTB-8.674
- 0.3SLX-2946.065
- 0.3SLY - 1SLZ-641.939
- 1.1NLB
Max Mx 31023 2031 1DL 30079
+ 1SIDL +7442.183
0.3CL + 0.3PLA
628.548
+ 0.33TLA246.055
+ 0.33BTA 14.771
+ 1SLX +1169.922
0.3SLY + 0.3SLZ
2597.675
+ 1.1LLA
Min Mx 31023 3062 1DL 30079
+ 1SIDL +-546.214
0.3CL + 0.3PLB
-544.29
+ 0.33TLB
-282.554
- 0.33BTB
-14.955
- 1SLX - 0.3SLY
-935.859- 0.3SLZ
-2157.187
- 1.1NLB
Max My 31271 1071 1DL 30327
+ 1SIDL +8172.002
0.3CL + 0.3PLB
238.536
+ 0.33TLB736.852
+ 0.33BTB6.399
+ 0.3SLX3194.596
+ 0.3SLY + 1SLZ
1037.48
Min My 31271 3054 1DL 30327
+ 1SIDL +-1274.53
0.3CL + 0.3PLA
-163.118
+ 0.33TLA
-764.643
- 0.33BTA-7.923
- 0.3SLX-2999.591
- 0.3SLY - 1SLZ
-639.297
- 1.1NLA
Max Mz 31271 1079 1DL 30327
+ 1SIDL +7968.573
0.3CL + 0.3PLA
646.644
+ 0.3PLB263.385
+ 0.33TLA + 0.33TLB
9.323 + 1278.867
0.33BTA + 0.33BTB
2682.466
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31271 1086 1DL 30327
+ 1SIDL +-746.996
0.3CL + 0.3PLA
-569.722
+ 0.3PLB-296.768
+ 0.33TLA +-11.262
0.33TLB - -1057.809
0.33BTA - 0.33BTB
-2273.122
- 1SLX - 0.3SLY - 0.3SLZ
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31272 1102 1DL 30332
+ 1SIDL +8076.924
0.3CL + 0.3PLA
191.563
+ 0.3PLB760.291
+ 0.33TLA + 0.33TLB
6.027 - 0.33BTA
2250.595- 0.33BTB
570.733
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 31024 1015 1DL 30084
+ 1SIDL +-1858.53
0.3SLX + 0.3SLY
-168.498
+ 1SLZ -728.456 -8.386 -2290.412 -573.031
Max Fy 31272 1079 1DL 30328
+ 1SIDL +7473.562
0.3CL + 0.3PLA
624.577
+ 0.3PLB285.702
+ 0.33TLA + 0.33TLB
9.602 + 1092.723
0.33BTA + 0.33BTB
2501.126
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31272 1086 1DL 30328
+ 1SIDL +-981.009
0.3CL + 0.3PLA
-592.633
+ 0.3PLB-274.106
+ 0.33TLA +-11.452
0.33TLB - -1241.429
0.33BTA - 0.33BTB
-2461.543
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31272 3054 1DL 30332
+ 1SIDL + 7881.03
0.3CL + 0.3PLA
200.719
+ 0.33TLA 765.26
- 0.33BTA 6.630
- 0.3SLX2234.277
- 0.3SLY - 1SLZ599.291
- 1.1NLA
Min Fz 31272 3078 1DL 30328
+ 1SIDL +-1571.16
0.3CL + 0.3PLB
-185.368
+ 0.33TLB
-754.184
- 0.33BTB-8.770
- 0.3SLX-3119.528
- 0.3SLY - 1SLZ
-820.064
- 1.1NLB
Max Mx 31024 2031 1DL 30080
+ 1SIDL +7395.782
0.3CL + 0.3PLA
608.709
+ 0.33TLA268.741
+ 0.33BTA 13.868
+ 1SLX +1002.162
0.3SLY + 0.3SLZ
2434.584
+ 1.1LLA
Min Mx 31024 3062 1DL 30080
+ 1SIDL +-1214.17
0.3CL + 0.3PLB
-567.061
+ 0.33TLB-262.63
- 0.33BTB
-13.953
- 1SLX --1118.396
0.3SLY - 0.3SLZ
-2344.392
- 1.1NLB
Max My 31272 1071 1DL 30328
+ 1SIDL +7792.461
0.3CL + 0.3PLB
217.411
+ 0.33TLB757.946
+ 0.33BTB6.570
+ 0.3SLX3016.339
+ 0.3SLY + 1SLZ
863.888
Min My 31272 3054 1DL 30328
+ 1SIDL +-1564.61
0.3CL + 0.3PLA
-184.781
+ 0.33TLA
-742.948
- 0.33BTA-7.995
- 0.3SLX-3173.094
- 0.3SLY - 1SLZ
-817.461
- 1.1NLA
Max Mz 31272 1079 1DL 30328
+ 1SIDL +7473.562
0.3CL + 0.3PLA
624.577
+ 0.3PLB285.702
+ 0.33TLA + 0.33TLB
9.602 + 1092.723
0.33BTA + 0.33BTB
2501.126
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31272 1086 1DL 30328
+ 1SIDL +-981.009
0.3CL + 0.3PLA
-592.633
+ 0.3PLB-274.106
+ 0.33TLA +-11.452
0.33TLB - -1241.429
0.33BTA - 0.33BTB
-2461.543
- 1SLX - 0.3SLY - 0.3SLZ
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31273 1095 1DL 30329
+ 1SIDL +8157.407
0.3CL + 0.3PLA
241.181
+ 0.3PLB757.998
+ 0.33TLA + 0.33TLB
6.713 + 2980.272
0.33BTA + 0.33BTB
1030.975
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 31397 1015 1DL 30457
+ 1SIDL +-1444.35
0.3SLX + 0.3SLY
-153.761
+ 1SLZ -725.228 -8.523 -2293.783 -443.817
Max Fy 31149 1079 1DL 30205
+ 1SIDL + 0.3CL
7512.8
+ 0.3PLA
643.95
+ 0.3PLB270.965
+ 0.33TLA + 0.33TLB
9.972 + 1003.109
0.33BTA + 0.33BTB
2663.623
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31273 1086 1DL 30329
+ 1SIDL +-496.716
0.3CL + 0.3PLA
-567.39
+ 0.3PLB-267.346
+ 0.33TLA +-11.413
0.33TLB - -1186.396
0.33BTA - 0.33BTB
-2257.153
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31273 3054 1DL 30333
+ 1SIDL +7860.765
0.3CL + 0.3PLA
214.912
+ 0.33TLA763.268
- 0.33BTA 6.583
- 0.3SLX2217.657
- 0.3SLY - 1SLZ713.969
- 1.1NLA
Min Fz 31273 3078 1DL 30329
+ 1SIDL + 0.3CL
-1253.8
+ 0.3PLB
-157.149
+ 0.33TLB
-751.863
- 0.33BTB-8.702
- 0.3SLX-3103.237
- 0.3SLY - 1SLZ
-598.495
- 1.1NLB
Max Mx 31025 2031 1DL 30081
+ 1SIDL +7179.281
0.3CL + 0.3PLA
626.214
+ 0.33TLA265.631
+ 0.33BTA 13.988
+ 1SLX +967.153
0.3SLY + 0.3SLZ
2582.416
+ 1.1LLA
Min Mx 31025 3062 1DL 30081
+ 1SIDL +-479.846
0.3CL + 0.3PLB
-542.263
+ 0.33TLB
-258.938
- 0.33BTB
-14.042
- 1SLX --1088.079
0.3SLY - 0.3SLZ
-2144.427
- 1.1NLB
Max My 31273 1071 1DL 30329
+ 1SIDL +7980.971
0.3CL + 0.3PLB
231.74
+ 0.33TLB756.271
+ 0.33BTB6.537
+ 0.3SLX2994.816
+ 0.3SLY + 1SLZ
992.125
Min My 31273 3054 1DL 30329
+ 1SIDL +-1242.64
0.3CL + 0.3PLA
-156.628
+ 0.33TLA
-740.622
- 0.33BTA-7.950
- 0.3SLX-3156.844
- 0.3SLY - 1SLZ
-596.448
- 1.1NLA
Max Mz 31149 1079 1DL 30205
+ 1SIDL + 0.3CL
7512.8
+ 0.3PLA
643.95
+ 0.3PLB270.965
+ 0.33TLA + 0.33TLB
9.972 + 1003.109
0.33BTA + 0.33BTB
2663.623
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31273 1086 1DL 30329
+ 1SIDL +-496.716
0.3CL + 0.3PLA
-567.39
+ 0.3PLB-267.346
+ 0.33TLA +-11.413
0.33TLB - -1186.396
0.33BTA - 0.33BTB
-2257.153
- 1SLX - 0.3SLY - 0.3SLZ

c) Static LC 1001-1006
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31270 1006 1DL 30326
+ 1SIDL +4522.807
1CL + 1PLA +-38.385
1PLB + 1.1TLA
-20.795
+ 1.1TLB --2.310
1.1BTA - 1.1BTB
139.826 -203.15
Min Fx 31022 1003 1DL 30078
+ 1SIDL +3338.669
1CL + 1PLB + 54.172
1.1TLB + -26.373
1.1BTB -0.525 173.877 169.345
Max Fy 31022 1005 1DL 30078
+ 1SIDL +3728.086
1CL + 1PLA + 1PLB
82.07
+ 1.1TLA
-26.13
+ 1.1TLB +0.061
1.1BTA + 161.393
1.1BTB 269.068
Min Fy 31394 1006 1DL 30450
+ 1SIDL +4519.729
1CL + 1PLA +-41.307
1PLB + 1.1TLA
-25.029
+ 1.1TLB --2.598
1.1BTA - 1.1BTB
152.644 -217.905
Max Fz 31394 1001 1DL 30450
+ 1SIDL +3528.989
1CL + 1PLA + 44.979
1.1TLA + 1.1BTA
-8.553 -0.461 57.09 121.654
Min Fz 31022 1003 1DL 30078
+ 1SIDL +3338.669
1CL + 1PLB + 54.172
1.1TLB + -26.373
1.1BTB -0.525 173.877 169.345
Max Mx 31022 1001 1DL 30078
+ 1SIDL + 3491.33
1CL + 1PLA + 54.672
1.1TLA + 1.1BTA
-17.17 0.547 101.074 169.884
Min Mx 31394 1006 1DL 30450
+ 1SIDL +4519.729
1CL + 1PLA +-41.307
1PLB + 1.1TLA
-25.029
+ 1.1TLB --2.598
1.1BTA - 1.1BTB
152.644 -217.905
Max My 31022 1003 1DL 30078
+ 1SIDL +3338.669
1CL + 1PLB + 54.172
1.1TLB + -26.373
1.1BTB -0.525 173.877 169.345
Min My 31394 1001 1DL 30454
+ 1SIDL +3528.989
1CL + 1PLA + 44.979
1.1TLA + 1.1BTA
-8.553 -0.461 48.536 76.675
Max Mz 31022 1005 1DL 30078
+ 1SIDL +3728.086
1CL + 1PLA + 1PLB
82.07
+ 1.1TLA
-26.13
+ 1.1TLB +0.061
1.1BTA + 161.393
1.1BTB 269.068
Min Mz 31394 1006 1DL 30450
+ 1SIDL +4519.729
1CL + 1PLA +-41.307
1PLB + 1.1TLA
-25.029
+ 1.1TLB --2.598
1.1BTA - 1.1BTB
152.644 -217.905
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31147 1005 1DL 30203
+ 1SIDL + 4868.12
1CL + 1PLA +109.082
1PLB + 1.1TLA
-24.827
+ 1.1TLB +0.155
1.1BTA + 160.926
1.1BTB 496.237
Min Fx 31023 1004 1DL 30079
+ 1SIDL +3663.019
1CL + 1PLB + 22.487
1.1TLB - 1.1BTB
-22.302 -0.394 158.722 154.006
Max Fy 31023 1005 1DL 30079
+ 1SIDL +4755.201
1CL + 1PLA +110.299
1PLB + 1.1TLA
-27.557
+ 1.1TLB +0.087
1.1BTA + 172.984
1.1BTB 501.115
Min Fy 31395 1006 1DL 30451
+ 1SIDL +4134.326
1CL + 1PLA +-12.545
1PLB + 1.1TLA
-24.405
+ 1.1TLB --2.576
1.1BTA - 1.1BTB
147.556 18.526
Max Fz 31395 1001 1DL 30451
+ 1SIDL +4204.386
1CL + 1PLA + 70.342
1.1TLA + 1.1BTA
-9.545 -0.467 65.162 330.163
Min Fz 31023 1005 1DL 30079
+ 1SIDL +4755.201
1CL + 1PLA +110.299
1PLB + 1.1TLA
-27.557
+ 1.1TLB +0.087
1.1BTA + 172.984
1.1BTB 501.115
Max Mx 31023 1001 1DL 30079
+ 1SIDL +4163.458
1CL + 1PLA + 79.694
1.1TLA + -18.063
1.1BTA 0.558 108.318 375.579
Min Mx 31395 1006 1DL 30451
+ 1SIDL +4134.326
1CL + 1PLA +-12.545
1PLB + 1.1TLA
-24.405
+ 1.1TLB --2.576
1.1BTA - 1.1BTB
147.556 18.526
Max My 31023 1003 1DL 30079
+ 1SIDL +4003.445
1CL + 1PLB + 1.1TLB
78.42 + -27.258
1.1BTB -0.496 181.054 368.665
Min My 31395 1001 1DL 30455
+ 1SIDL +4204.386
1CL + 1PLA + 70.342
1.1TLA + 1.1BTA
-9.545 -0.467 55.616 259.821
Max Mz 31023 1005 1DL 30079
+ 1SIDL +4755.201
1CL + 1PLA +110.299
1PLB + 1.1TLA
-27.557
+ 1.1TLB +0.087
1.1BTA + 172.984
1.1BTB 501.115
Min Mz 31395 1006 1DL 30451
+ 1SIDL +4134.326
1CL + 1PLA +-12.545
1PLB + 1.1TLA
-24.405
+ 1.1TLB --2.576
1.1BTA - 1.1BTB
147.556 18.526
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31148 1006 1DL 30204
+ 1SIDL +4444.676
1CL + 1PLA +-34.366
1PLB + 1.1TLA
12.431
+ 1.1TLB --1.442
1.1BTA - 1.1BTB
-115.75 -184.311
Min Fx 31024 1001 1DL 30080
+ 1SIDL +3223.753
1CL + 1PLA + 55.233
1.1TLA + 1.1BTA
6.399 0.685 -92.775 174.488
Max Fy 31024 1005 1DL 30080
+ 1SIDL +3597.968
1CL + 1PLA + 82.245
1PLB + 1.1TLA
0.497
+ 1.1TLB +0.258
1.1BTA + 1.1BTB
-57.647 270.485
Min Fy 31396 1006 1DL 30452
+ 1SIDL +4302.634
1CL + 1PLA +-40.911
1PLB + 1.1TLA
3.961
+ 1.1TLB --2.653
1.1BTA - 1.1BTB
-85.637 -214.666
Max Fz 31396 1001 1DL 30452
+ 1SIDL + 3236.97
1CL + 1PLA + 45.679
1.1TLA + 1.1BTA
15.117 -0.342 -137.587 127.415
Min Fz 31024 1003 1DL 30080
+ 1SIDL +3404.859
1CL + 1PLB + 1.1TLB
53.88 + 1.1BTB
-2.718 -0.389 -20.684 166.928
Max Mx 31024 1001 1DL 30080
+ 1SIDL +3223.753
1CL + 1PLA + 55.233
1.1TLA + 1.1BTA
6.399 0.685 -92.775 174.488
Min Mx 31396 1006 1DL 30452
+ 1SIDL +4302.634
1CL + 1PLA +-40.911
1PLB + 1.1TLA
3.961
+ 1.1TLB --2.653
1.1BTA - 1.1BTB
-85.637 -214.666
Max My 31024 1003 1DL 30080
+ 1SIDL +3404.859
1CL + 1PLB + 1.1TLB
53.88 + 1.1BTB
-2.718 -0.389 -20.684 166.928
Min My 31396 1001 1DL 30452
+ 1SIDL + 3236.97
1CL + 1PLA + 45.679
1.1TLA + 1.1BTA
15.117 -0.342 -137.587 127.415
Max Mz 31024 1005 1DL 30080
+ 1SIDL +3597.968
1CL + 1PLA + 82.245
1PLB + 1.1TLA
0.497
+ 1.1TLB +0.258
1.1BTA + 1.1BTB
-57.647 270.485
Min Mz 31396 1006 1DL 30452
+ 1SIDL +4302.634
1CL + 1PLA +-40.911
1PLB + 1.1TLA
3.961
+ 1.1TLB --2.653
1.1BTA - 1.1BTB
-85.637 -214.666
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31149 1005 1DL 30205
+ 1SIDL +4736.591
1CL + 1PLA +108.874
1PLB + 1.1TLA
5.499
+ 1.1TLB +0.350
1.1BTA + 1.1BTB
-88.243 494.54
Min Fx 31397 1002 1DL 30453
+ 1SIDL +3523.032
1CL + 1PLA + 13.266
1.1TLA - 1.1BTA
10.089 -1.978 -118.673 107.303
Max Fy 31025 1005 1DL 30081
+ 1SIDL +4625.083
1CL + 1PLA +110.124
1PLB + 1.1TLA
1.924
+ 1.1TLB +0.285
1.1BTA + 1.1BTB
-69.238 499.698
Min Fy 31397 1006 1DL 30453
+ 1SIDL +3917.232
1CL + 1PLA +-12.941
1PLB + 1.1TLA
3.337
+ 1.1TLB --2.632
1.1BTA - 1.1BTB
-80.55 15.287
Max Fz 31397 1001 1DL 30453
+ 1SIDL +3912.368
1CL + 1PLA + 69.642
1.1TLA + 1.1BTA
16.109 -0.349 -145.658 324.402
Min Fz 31025 1003 1DL 30081
+ 1SIDL +4069.636
1CL + 1PLB + 78.711
1.1TLB + 1.1BTB
-1.833 -0.359 -27.861 371.082
Max Mx 31025 1001 1DL 30081
+ 1SIDL +3895.881
1CL + 1PLA + 79.133
1.1TLA + 1.1BTA
7.292 0.696 -100.018 370.976
Min Mx 31397 1006 1DL 30453
+ 1SIDL +3917.232
1CL + 1PLA +-12.941
1PLB + 1.1TLA
3.337
+ 1.1TLB --2.632
1.1BTA - 1.1BTB
-80.55 15.287
Max My 31025 1003 1DL 30081
+ 1SIDL +4069.636
1CL + 1PLB + 78.711
1.1TLB + 1.1BTB
-1.833 -0.359 -27.861 371.082
Min My 31397 1001 1DL 30453
+ 1SIDL +3912.368
1CL + 1PLA + 69.642
1.1TLA + 1.1BTA
16.109 -0.349 -145.658 324.402
Max Mz 31025 1005 1DL 30081
+ 1SIDL +4625.083
1CL + 1PLA +110.124
1PLB + 1.1TLA
1.924
+ 1.1TLB +0.285
1.1BTA + 1.1BTB
-69.238 499.698
Min Mz 31397 1006 1DL 30453
+ 1SIDL +3917.232
1CL + 1PLA +-12.941
1PLB + 1.1TLA
3.337
+ 1.1TLB --2.632
1.1BTA - 1.1BTB
-80.55 15.287

2.2 Pile Loads

MDE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 9934 10422 10154 9991


Min Fx -2554 -2218 -2826 -2123
Max Fy 8889 10364 9443 9671
Min Fy -1340 -2087 -2155 -1412
Max Fz 9488 9849 9635 9572
Min Fz -1831 -1892 -2225 -1861
Max Mx 9934 9159 9588 9366
Min Mx -2554 -1018 -2260 -1276
Max My 9314 9968 9511 9740
Min My -1845 -1900 -2215 -1845
Max Mz 8889 10364 9525 9671
Min Mz -1340 -2087 -2155 -1412
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

ODE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 7977 8397 8077 8157


Min Fx -1625 -1442 -1859 -1444
Max Fy 7149 7969 7474 7513
Min Fy -437 -747 -981 -497
Max Fz 7770 8087 7881 7861
Min Fz -1249 -1269 -1571 -1254
Max Mx 7401 7442 7396 7179
Min Mx -1023 -546 -1214 -480
Max My 7646 8172 7792 7981
Min My -1259 -1275 -1565 -1243
Max Mz 7149 7969 7474 7513
Min Mz -437 -747 -981 -497

Static
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 4523 4868 4445 4737


Min Fx 3339 3663 3224 3523
Max Fy 3728 4755 3598 4625
Min Fy 4520 4134 4303 3917
Max Fz 3529 4204 3237 3912
Min Fz 3339 4755 3405 4070
Max Mx 3491 4163 3224 3896
Min Mx 4520 4134 4303 3917
Max My 3339 4003 3405 4070
Min My 3529 4204 3237 3912
Max Mz 3728 4755 3598 4625
Min Mz 4520 4134 4303 3917

3.1 Moment at Bottom Face:

Lever arm Z = Pile Centre to column face

Z = 0.80 m

Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or


2.0 m (P1+P2)xZ or (P3+P4)xZ, whichever
column is maximum

P kN
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = 510.276 kN.m
Design Moment, M = M1 - M2

Case M1 (kN.m) M = (M1 - M2) (kN.m)


MDE Seismic 16330.400 15743.582
ODE Seismic 13243.200 12732.924
Static 7684.000 7173.724

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
2
K = Mu/bd fcu = 0.020 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.95 d = 1626.88 mm
As = Mu / (fy z)
Ast = 24813.314 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 100 0 0 0 0

= 25530.349 mm2 OK

3.2 Moment at Top Face:

Lever arm Z = Pile Centre to column face

P kN Z = 0.80 m
2.0 m
column Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or
(P1+P2)xZ or (P3+P4)xZ, whichever
is minimum

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = -510.276 kN.m
Design Moment, M = M1 + M2

Case M1 (kN.m) M = (M1 + M2) (kN.m)


MDE Seismic -4304.000 -4890.818
ODE Seismic -2787.200 -3297.476
Static 0.000 0.000

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

K = Mu/bd2fcu = 0.006 K'


Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1713.23 mm
Hence, z = 0.95 d = 1627.57 mm
As = M u / (f y z)
Ast = 7705.103 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


23.547 100 0 0 0 0
(Y25 + Y22 ALT.)
= 22655.269 mm2 OK

3.3 Moment Capacity, Stress and Crack Width Check from Oasys

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 15740 20770 0.7579 OK
Minima
2 0.0 4891 20770 0.2355 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
26.64 OK
26.64 OK
Minima
-148.4 OK
-148.4 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fcu 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Oasys Results
Cocncrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
3 2.36 OK 3 13.21 OK
3 2.36 OK 3 13.21 OK
Minima Minima
3 -0.5797 OK 3 -47.27 OK
3 -0.5797 OK 3 -47.27 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.087 mm OK

3.4 Minimum Reinforcement


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4008.95 mm2/m
2
At bottom face, Provided = 4817 mm2/m
Astprovided > Astmin OK
At top face, Provided = 4275 mm2/m
Astprovided > Astmin OK

4.0 Shear Check


Total pile reaction, V1 = 20413 kN
As per Cl. 3.11.4.3, pg. 82, BS 8110-1: 1997, critical section for shear should be located 20% of the pile diameter inside
Distance of critical section for shear check from column face = 0.440 m
Factored weight per unit length due to soil and pile cap = 431.087 kN/m
Hence, downward reaction due to soil and pile cap weight,
V2 = weight per unit length x (length of pile cap - 0.5 x column size - distance of critical section)
V2 = 522 kN
Net reaction, Vu = V1 - V2 = 19891 kN
Width of pile cap available b = 5.300 m
Effective depth of pile cap d = 1.713 m
Area of tensile steel provided As = 25530 mm2
= 0.026 m2
Percentage of tensile steel provided 100As/(b.d) = 0.281 %
Shear stress = Vu /(b.d) = 2191.59 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.34 MPa
= 340 kN/sqm
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Sandeep
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

As per Cl. 3.11.4.4, pg. 82, BS 8110-1:1997,


Enhanced shear strength of concrete, say vc,1 = 2.d.vc /av
av = 0.440 m
Therefore, vc,1 = 2.65 MPa
= 2647 kN/sqm
Vus = Vu - vc,1 b d = -4129.74 kN

Requirement of shear reinforcement = Not Required

5.0 Check for punching shear


Total pile load = 40501 kN
From section 1.0 above, factored weight of pile cap + earthfill = 1987 kN
Hence, net punching shear force = 38514 kN
Effective depth of pile cap = 1.713 m
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, punching shear shall be checked at the perimeter of the column.
Shear perimeter = 8.000 m
Shearing Area = 13.700 m2
Punching Shear stress = 2811.259 kN/m2
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997,
Allowable punching shear stress = lesser of 0.8 fcu or 5 N/mm2 = 5.00 N/mm2
= 5000.000 kN/m2
OK
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, since the pile spacing is not greater than 3 times the pile diameter, no
additional punching shear check is required.
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR COLUMN C32


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Column No. = C32

No. of piles n = 4
Dia of pile = 1.20 m
Size of Column = 2.00 m x 2.00 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 5.30 m x 5.30 m


2
Area of pile cap = 28.09 m
Depth of pile cap D = 1.80 m
Volume of pile cap = 50.56 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 1264.05 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 36.14 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 722.70 kN

Total weight of (Pile cap + Earthfill) = 1986.75 kN

2.0 PILE LOADS

2.1 Summary of Staad Results (Forces at Bottom of Pile Cap)---

LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-


a) MDE Seismic
2378, 3131-3178,4101-4132, 5109-5124 & 6109-6124
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31518 2202 1.15DL
30578
+ 1.2SIDL
10200.75
+ 0.42CL 218.195
+ 0.42PLA + 0.42PLB
900.69 + 0.462TLA
8.205 + 0.462TLB
2965.7 - 0.462BTA
615.36- 0.462BTB - 0.3SLX - 0.3SLY
Min Fx 31518 2115 1.15DL
30578
+ 1.2SIDL
-1845.51
+ 0.3SLX-218.801
+ 0.3SLY + 1SLZ
-951.165 -10.824 -2713.249 -735.769
Max Fy 31518 2103 1.15DL
30574
+ 1.2SIDL
9376.74
+ 1.4CL +1176.03
1.4PLB + 1.54TLB
116.141+ 1.54BTB
18.404 712.852 4690.16
Min Fy 31518 2104 1.15DL
30578
+ 1.2SIDL
-1102.43
+ 1.4CL-1134.418
+ 1.4PLB + -171.857
1.54TLB - 1.54BTB
-20.973 -266.784 -3513.359
Max Fz 31518 3154 1.15DL
30578
+ 1.2SIDL
9871.766
+ 0.42CL 231.551
+ 0.42PLA + 0.462TLA
915.8 - 9.155
0.462BTA2909.535
- 0.3SLX - 0.3SLY
657.64
- 1SLZ - 1.54NLA
Min Fz 31518 3178 1.15DL
30574
+ 1.2SIDL
-1454.73
+ 0.42CL-229.251
+ 0.42PLB +-967.567
0.462TLB-11.831
- 0.462BTB
-3543.003
- 0.3SLX - 0.3SLY
-997.131
- 1SLZ - 1.54NLB
Max Mx 31518 2103 1.15DL
30574
+ 1.2SIDL
9376.74
+ 1.4CL +1176.03
1.4PLB + 1.54TLB
116.141+ 1.54BTB
18.404 712.852 4690.16
Min Mx 31518 2104 1.15DL
30578
+ 1.2SIDL
-1102.43
+ 1.4CL-1134.418
+ 1.4PLB + -171.857
1.54TLB - 1.54BTB
-20.973 -266.784 -3513.359
Max My 31518 3147 1.15DL
30574
+ 1.2SIDL
9817.104
+ 0.42CL 254.086
+ 0.42PLA +899.765
0.462TLA + 8.280
0.462BTA
3914.699
+ 0.3SLX + 0.3SLY
972.167+ 1SLZ + 1.54NLA
Min My 31518 3154 1.15DL
30574
+ 1.2SIDL
-1505.62
+ 0.42CL-228.516
+ 0.42PLA +-943.085
0.462TLA --10.449
0.462BTA
-3655.139
- 0.3SLX - 0.3SLY
-994.161
- 1SLZ - 1.54NLA
Max Mz 31518 2103 1.15DL
30574
+ 1.2SIDL
9376.74
+ 1.4CL +1176.03
1.4PLB + 1.54TLB
116.141+ 1.54BTB
18.404 712.852 4690.16
Min Mz 31518 2104 1.15DL
30578
+ 1.2SIDL
-1102.43
+ 1.4CL-1134.418
+ 1.4PLB + -171.857
1.54TLB - 1.54BTB
-20.973 -266.784 -3513.359
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.14
+ 1.4CL 1204.986
+ 1.4PLB + 1.54TLB
118.746+ 1.54BTB
18.186 754.235 4928.127
Min Fx 31519 2115 1.15DL
30579
+ 1.2SIDL
-1708.97
+ 0.3SLX-201.159
+ 0.3SLY + 1SLZ
-952.444 -10.532 -2716.018 -592.641
Max Fy 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.14
+ 1.4CL 1204.986
+ 1.4PLB + 1.54TLB
118.746+ 1.54BTB
18.186 754.235 4928.127
Min Fy 31519 2104 1.15DL
30579
+ 1.2SIDL
-1623.4
+ 1.4CL-1106.526
+ 1.4PLB + -175.617
1.54TLB - 1.54BTB
-20.696 -294.366 -3311.915
Max Fz 31519 3154 1.15DL
30579
+ 1.2SIDL
10192.91
+ 0.42CL 267.799
+ 0.42PLA +916.413
0.462TLA - 8.882
0.462BTA2917.057
- 0.3SLX - 0.3SLY
903.63
- 1SLZ - 1.54NLA
Min Fz 31519 3178 1.15DL
30575
+ 1.2SIDL
-1435.86
+ 0.42CL-209.395
+ 0.42PLB +-968.667
0.462TLB-11.508
- 0.462BTB
-3547.731
- 0.3SLX - 0.3SLY
-820.384
- 1SLZ - 1.54NLB
Max Mx 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.14
+ 1.4CL 1204.986
+ 1.4PLB + 1.54TLB
118.746+ 1.54BTB
18.186 754.235 4928.127
Min Mx 31519 2104 1.15DL
30579
+ 1.2SIDL
-1623.4
+ 1.4CL-1106.526
+ 1.4PLB + -175.617
1.54TLB - 1.54BTB
-20.696 -294.366 -3311.915
Max My 31519 3147 1.15DL
30575
+ 1.2SIDL
10431.61
+ 0.42CL 290.596
+ 0.42PLA +899.924
0.462TLA + 8.040
0.462BTA
3927.081
+ 0.3SLX +1258.742
0.3SLY + 1SLZ + 1.54NLA
Min My 31519 3154 1.15DL
30575
+ 1.2SIDL
-1479.72
+ 0.42CL-208.646
+ 0.42PLA +-944.193
0.462TLA --10.176
0.462BTA
-3659.794
- 0.3SLX - 0.3SLY
-817.266
- 1SLZ - 1.54NLA
Max Mz 31519 2103 1.15DL
30575
+ 1.2SIDL
10696.14
+ 1.4CL 1204.986
+ 1.4PLB + 1.54TLB
118.746+ 1.54BTB
18.186 754.235 4928.127
Min Mz 31519 2104 1.15DL
30579
+ 1.2SIDL
-1623.4
+ 1.4CL-1106.526
+ 1.4PLB + -175.617
1.54TLB - 1.54BTB
-20.696 -294.366 -3311.915
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31520 2104 1.15DL
30576
+ 1.2SIDL
10170.24
+ 1.4CL 1099.674
+ 1.4PLB + 1.54TLB
141.558- 1.54BTB
18.104 542.525 4402.12
Min Fx 31520 2103 1.15DL
30580
+ 1.2SIDL
-2223.06
+ 1.4CL-1057.583
+ 1.4PLB + -142.058
1.54TLB + 1.54BTB
-20.528 -512.402 -3298.257
Max Fy 31520 2103 1.15DL
30576
+ 1.2SIDL
9700.8
+ 1.4CL 1176.938
+ 1.4PLB + 1.54TLB
146.984+ 1.54BTB
19.087 523.063 4697.542
Min Fy 31520 2104 1.15DL
30580
+ 1.2SIDL
-1753.61
+ 1.4CL-1134.847
+ 1.4PLB + -147.484
1.54TLB - 1.54BTB
-21.511 -498.366 -3516.416
Max Fz 31520 3154 1.15DL
30580
+ 1.2SIDL
9899.423
+ 0.42CL 240.181
+ 0.42PLA +944.294
0.462TLA - 9.294
0.462BTA2718.694
- 0.3SLX - 0.3SLY
704.266
- 1SLZ - 1.54NLA
Min Fz 31520 3178 1.15DL
30576
+ 1.2SIDL
-1906.01
+ 0.42CL-237.145
+ 0.42PLB + -941.18
0.462TLB-11.908
- 0.462BTB
-3777.062
- 0.3SLX - 0.3SLY
-1048.568
- 1SLZ - 1.54NLB
Max Mx 31520 2103 1.15DL
30576
+ 1.2SIDL
9700.8
+ 1.4CL 1176.938
+ 1.4PLB + 1.54TLB
146.984+ 1.54BTB
19.087 523.063 4697.542
Min Mx 31520 2104 1.15DL
30580
+ 1.2SIDL
-1753.61
+ 1.4CL-1134.847
+ 1.4PLB + -147.484
1.54TLB - 1.54BTB
-21.511 -498.366 -3516.416
Max My 31520 3147 1.15DL
30576
+ 1.2SIDL
9659.323
+ 0.42CL 262.984
+ 0.42PLA + 0.462TLA
927.8 + 8.465
0.462BTA
3701.284
+ 0.3SLX +1031.801
0.3SLY + 1SLZ + 1.54NLA
Min My 31520 3154 1.15DL
30576
+ 1.2SIDL
-1865.35
+ 0.42CL-236.384
+ 0.42PLA +-916.718
0.462TLA --10.524
0.462BTA
-3889.028
- 0.3SLX - -1045.352
0.3SLY - 1SLZ - 1.54NLA
Max Mz 31520 2103 1.15DL
30576
+ 1.2SIDL
9700.8
+ 1.4CL 1176.938
+ 1.4PLB + 1.54TLB
146.984+ 1.54BTB
19.087 523.063 4697.542
Min Mz 31520 2104 1.15DL
30580
+ 1.2SIDL
-1753.61
+ 1.4CL-1134.847
+ 1.4PLB + -147.484
1.54TLB - 1.54BTB
-21.511 -498.366 -3516.416
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31521 2195 1.15DL
30577
+ 1.2SIDL
10327.11
+ 0.42CL 294.043
+ 0.42PLA +936.568
0.42PLB + 0.462TLA
9.002 + 0.462TLB
3656.471 + 0.462BTA
1251.098+ 0.462BTB + 0.3SLX + 0.3S
Min Fx 31521 2115 1.15DL
30581
+ 1.2SIDL
-1753.46
+ 0.3SLX +-193.32
0.3SLY + 1SLZ
-925.858 -10.598 -2898.84 -552.549
Max Fy 31521 2103 1.15DL
30577
+ 1.2SIDL
10101.23
+ 1.4CL 1204.079
+ 1.4PLB + 1.54TLB
144.366+ 1.54BTB
18.884 481.47 4920.753
Min Fy 31521 2104 1.15DL
30581
+ 1.2SIDL
-1355.6
+ 1.4CL-1106.098
+ 1.4PLB + -143.712
1.54TLB - 1.54BTB
-21.250 -470.567 -3308.864
Max Fz 31521 3154 1.15DL
30581
+ 1.2SIDL
9890.342
+ 0.42CL 259.254
+ 0.42PLA +943.676
0.462TLA - 9.030
0.462BTA2711.097
- 0.3SLX - 0.3SLY
858.446
- 1SLZ - 1.54NLA
Min Fz 31521 3178 1.15DL
30577
+ 1.2SIDL
-1556.92
+ 0.42CL-201.585
+ 0.42PLB +-940.076
0.462TLB-11.594
- 0.462BTB
-3772.259
- 0.3SLX - 0.3SLY
-770.424
- 1SLZ - 1.54NLB
Max Mx 31521 2103 1.15DL
30577
+ 1.2SIDL
10101.23
+ 1.4CL 1204.079
+ 1.4PLB + 1.54TLB
144.366+ 1.54BTB
18.884 481.47 4920.753
Min Mx 31521 2104 1.15DL
30581
+ 1.2SIDL
-1355.6
+ 1.4CL-1106.098
+ 1.4PLB + -143.712
1.54TLB - 1.54BTB
-21.250 -470.567 -3308.864
Max My 31521 3147 1.15DL
30577
+ 1.2SIDL
9943.603
+ 0.42CL 281.783
+ 0.42PLA +927.636
0.462TLA + 8.234
0.462BTA
3688.827
+ 0.3SLX +1200.585
0.3SLY + 1SLZ + 1.54NLA
Min My 31521 3154 1.15DL
30577
+ 1.2SIDL
-1509.22
+ 0.42CL-200.862
+ 0.42PLA +-915.605
0.462TLA --10.260
0.462BTA
-3884.297
- 0.3SLX - 0.3SLY
-767.551
- 1SLZ - 1.54NLA
Max Mz 31521 2103 1.15DL
30577
+ 1.2SIDL
10101.23
+ 1.4CL 1204.079
+ 1.4PLB + 1.54TLB
144.366+ 1.54BTB
18.884 481.47 4920.753
Min Mz 31521 2104 1.15DL
30581
+ 1.2SIDL
-1355.6
+ 1.4CL-1106.098
+ 1.4PLB + -143.712
1.54TLB - 1.54BTB
-21.250 -470.567 -3308.864
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

LC 1001-1190, 2031-2078, 3031-3078, 4001-


b) ODE Seismic
4032, 5009-5024 & 6009-6024
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31518 1102 1DL 30578
+ 1SIDL +8337.997
0.3CL + 0.3PLA
176.658
+ 0.3PLB716.664
+ 0.33TLA + 0.33TLB
6.515 - 0.33BTA
2368.61- 0.33BTB
495.679
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 31518 1015 1DL 30578
+ 1SIDL +-1203.94
0.3SLX + 0.3SLY
-173.415
+ 1SLZ -759.353 -8.702 -2154.493 -587.734
Max Fy 31518 1079 1DL 30574
+ 1SIDL +7541.264
0.3CL + 0.3PLA
609.028
+ 0.3PLB270.801
+ 0.33TLA + 10.745
0.33TLB + 1292.328
0.33BTA + 0.33BTB
2411.906
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31518 1086 1DL 30574
+ 1SIDL +-163.173
0.3CL + 0.3PLA
-589.039
+ 0.3PLB-313.961
+ 0.33TLA +-12.745
0.33TLB - 0.33BTA
-1029.09- 0.33BTB
-2443.257
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31518 3054 1DL 30578
+ 1SIDL +8103.011
0.3CL + 0.3PLA
186.198
+ 0.33TLA727.457
- 0.33BTA 7.193
- 0.3SLX2328.492
- 0.3SLY - 1SLZ525.879
- 1.1NLA
Min Fz 31518 3078 1DL 30574
+ 1SIDL +-924.812
0.3CL + 0.3PLB
-180.879
+ 0.33TLB
-771.069
- 0.33BTB-9.421
- 0.3SLX-2820.462
- 0.3SLY - 1SLZ
-791.347
- 1.1NLB
Max Mx 31518 3055 1DL 30574
+ 1SIDL +7381.617
0.3CL + 0.3PLB
601.947
+ 0.33TLB275.559
+ 0.33BTB11.060
+ 1SLX +1277.034
0.3SLY + 0.3SLZ
2388.509
+ 1.1NLB
Min Mx 31518 3062 1DL 30574
+ 1SIDL +-361.808
0.3CL + 0.3PLB
-580.024
+ 0.33TLB
-320.656
- 0.33BTB
-13.054
- 1SLX - 0.3SLY
-999.903- 0.3SLZ
-2405.638
- 1.1NLB
Max My 31518 3047 1DL 30574
+ 1SIDL +8063.967
0.3CL + 0.3PLA
202.294
+ 0.33TLA716.003
+ 0.33BTA6.568
+ 0.3SLX 3126.388
+ 0.3SLY + 1SLZ
771.143
+ 1.1NLA
Min My 31518 3054 1DL 30574
+ 1SIDL +-961.162
0.3CL + 0.3PLA
-180.354
+ 0.33TLA
-753.581
- 0.33BTA-8.434
- 0.3SLX-2900.559
- 0.3SLY - 1SLZ
-789.225
- 1.1NLA
Max Mz 31518 1079 1DL 30574
+ 1SIDL +7541.264
0.3CL + 0.3PLA
609.028
+ 0.3PLB270.801
+ 0.33TLA + 10.745
0.33TLB + 1292.328
0.33BTA + 0.33BTB
2411.906
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31518 1086 1DL 30574
+ 1SIDL +-163.173
0.3CL + 0.3PLA
-589.039
+ 0.3PLB-313.961
+ 0.33TLA +-12.745
0.33TLB - 0.33BTA
-1029.09- 0.33BTB
-2443.257
- 1SLX - 0.3SLY - 0.3SLZ
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31519 1095 1DL 30575
+ 1SIDL +8708.132
0.3CL + 0.3PLA
241.483
+ 0.3PLB721.159
+ 0.33TLA + 0.33TLB
6.908 + 3124.196
0.33BTA + 0.33BTB
1046.587
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 31519 1015 1DL 30579
+ 1SIDL +-1073.74
0.3SLX + 0.3SLY
-157.577
+ 1SLZ -760.4 -8.466 -2156.468 -460.838
Max Fy 31519 1079 1DL 30575
+ 1SIDL + 0.3CL
8256.9
+ 0.3PLA
636.375
+ 0.3PLB272.118
+ 0.33TLA + 10.581
0.33TLB + 1314.209
0.33BTA + 0.33BTB
2633.449
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31519 1086 1DL 30575
+ 1SIDL +-330.711
0.3CL + 0.3PLA
-566.175
+ 0.3PLB-316.099
+ 0.33TLA +-12.543
0.33TLB - -1044.284
0.33BTA - 0.33BTB
-2252.045
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31519 3054 1DL 30579
+ 1SIDL +8388.062
0.3CL + 0.3PLA
216.671
+ 0.33TLA727.898
- 0.33BTA 6.977
- 0.3SLX2334.784
- 0.3SLY - 1SLZ733.373
- 1.1NLA
Min Fz 31519 3078 1DL 30575
+ 1SIDL + 0.3CL
-878.66
+ 0.3PLB
-163.46
+ 0.33TLB
-771.987
- 0.33BTB-9.164
- 0.3SLX-2823.844
- 0.3SLY - 1SLZ
-637.381
- 1.1NLB
Max Mx 31519 3055 1DL 30575
+ 1SIDL +7989.617
0.3CL + 0.3PLB
627.913
+ 0.33TLB277.048
+ 0.33BTB10.888
+ 1SLX +1297.515
0.3SLY + 0.3SLZ
2598.704
+ 1.1NLB
Min Mx 31519 3062 1DL 30575
+ 1SIDL + 0.3CL
-427.43
+ 0.3PLB
-558.352
+ 0.33TLB
-322.946
- 0.33BTB
-12.837
- 1SLX --1013.857
0.3SLY - 0.3SLZ
-2224.243
- 1.1NLB
Max My 31519 3047 1DL 30575
+ 1SIDL +8558.558
0.3CL + 0.3PLA
232.955
+ 0.33TLA716.121
+ 0.33BTA6.376
+ 0.3SLX3136.29
+ 0.3SLY + 1SLZ
1012.387
+ 1.1NLA
Min My 31519 3054 1DL 30575
+ 1SIDL +-909.989
0.3CL + 0.3PLA
-162.925
+ 0.33TLA
-754.506
- 0.33BTA-8.212
- 0.3SLX-2903.889
- 0.3SLY - 1SLZ
-635.153
- 1.1NLA
Max Mz 31519 1079 1DL 30575
+ 1SIDL + 0.3CL
8256.9
+ 0.3PLA
636.375
+ 0.3PLB272.118
+ 0.33TLA + 10.581
0.33TLB + 1314.209
0.33BTA + 0.33BTB
2633.449
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31519 1086 1DL 30575
+ 1SIDL +-330.711
0.3CL + 0.3PLA
-566.175
+ 0.3PLB-316.099
+ 0.33TLA +-12.543
0.33TLB - -1044.284
0.33BTA - 0.33BTB
-2252.045
- 1SLX - 0.3SLY - 0.3SLZ
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31520 1102 1DL 30580
+ 1SIDL +8296.207
0.3CL + 0.3PLA
183.562
+ 0.3PLB742.226
+ 0.33TLA + 0.33TLB
6.612 - 0.33BTA
2195.93- 0.33BTB
533.012
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 31520 1015 1DL 30580
+ 1SIDL +-1515.17
0.3SLX + 0.3SLY
-179.697
+ 1SLZ -738.489 -8.744 -2317.093 -620.611
Max Fy 31520 1079 1DL 30576
+ 1SIDL +7645.552
0.3CL + 0.3PLA
611.61
+ 0.3PLB297.025
+ 0.33TLA + 11.099
0.33TLB + 1111.354
0.33BTA + 0.33BTB
2429.868
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31520 1086 1DL 30576
+ 1SIDL +-617.862
0.3CL + 0.3PLA +-591
0.3PLB-291.416
+ 0.33TLA +-13.006
0.33TLB - -1249.102
0.33BTA - 0.33BTB
-2456.136
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31520 3054 1DL 30580
+ 1SIDL +8110.168
0.3CL + 0.3PLA
193.087
+ 0.33TLA 751.692
- 0.33BTA 7.309
- 0.3SLX2165.382
- 0.3SLY - 1SLZ563.121
- 1.1NLA
Min Fz 31520 3078 1DL 30576
+ 1SIDL +-1290.73
0.3CL + 0.3PLB
-187.141
+ 0.33TLB-748.516
- 0.33BTB-9.477
- 0.3SLX-3019.536
- 0.3SLY - 1SLZ --832.1
1.1NLB
Max Mx 31520 3055 1DL 30576
+ 1SIDL +7601.907
0.3CL + 0.3PLB
604.305
+ 0.33TLB 300.798
+ 0.33BTB11.398
+ 1SLX +1104.168
0.3SLY + 0.3SLZ
2404.631
+ 1.1NLB
Min Mx 31520 3062 1DL 30576
+ 1SIDL +-832.948
0.3CL + 0.3PLB
-582.018
+ 0.33TLB-299.423
- 0.33BTB
-13.298
- 1SLX - 0.3SLY
-1209.14- 0.3SLZ
-2418.799
- 1.1NLB
Max My 31520 3047 1DL 30576
+ 1SIDL + 7938.67
0.3CL + 0.3PLA
209.375
+ 0.33TLA 739.91
+ 0.33BTA6.717
+ 0.3SLX 2943.453
+ 0.3SLY + 1SLZ818.58
+ 1.1NLA
Min My 31520 3054 1DL 30576
+ 1SIDL +-1261.68
0.3CL + 0.3PLA
-186.597
+ 0.33TLA-731.043
- 0.33BTA-8.488
- 0.3SLX-3099.512
- 0.3SLY - 1SLZ
-829.803
- 1.1NLA
Max Mz 31520 1079 1DL 30576
+ 1SIDL +7645.552
0.3CL + 0.3PLA
611.61
+ 0.3PLB297.025
+ 0.33TLA + 11.099
0.33TLB + 1111.354
0.33BTA + 0.33BTB
2429.868
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31520 1086 1DL 30576
+ 1SIDL +-617.862
0.3CL + 0.3PLA +-591
0.3PLB-291.416
+ 0.33TLA +-13.006
0.33TLB - -1249.102
0.33BTA - 0.33BTB
-2456.136
- 1SLX - 0.3SLY - 0.3SLZ
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31521 1095 1DL 30577
+ 1SIDL + 0.3CL
8444.4
+ 0.3PLA
234.699
+ 0.3PLB746.169
+ 0.33TLA + 0.33TLB
7.081 + 2910.379
0.33BTA + 0.33BTB
1002.207
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 31521 1015 1DL 30581
+ 1SIDL +-1122.17
0.3SLX + 0.3SLY
-151.362
+ 1SLZ -737.438 -8.515 -2315.057 -429.109
Max Fy 31521 1079 1DL 30577
+ 1SIDL +7849.371
0.3CL + 0.3PLA
633.813
+ 0.3PLB295.699
+ 0.33TLA + 10.945
0.33TLB + 1089.335
0.33BTA + 0.33BTB
2615.833
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 31521 1086 1DL 30577
+ 1SIDL +-273.582
0.3CL + 0.3PLA
-564.234
+ 0.3PLB-289.269
+ 0.33TLA +-12.813
0.33TLB - 0.33BTA
-1233.77- 0.33BTB
-2239.514
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 31521 3054 1DL 30581
+ 1SIDL + 8132.42
0.3CL + 0.3PLA
209.85
+ 0.33TLA751.246
- 0.33BTA 7.100
- 0.3SLX2159.028
- 0.3SLY - 1SLZ697.279
- 1.1NLA
Min Fz 31521 3078 1DL 30577
+ 1SIDL +-981.779
0.3CL + 0.3PLB
-157.265
+ 0.33TLB
-747.593
- 0.33BTB-9.226
- 0.3SLX-3016.092
- 0.3SLY - 1SLZ
-597.803
- 1.1NLB
Max Mx 31521 3055 1DL 30577
+ 1SIDL +7698.088
0.3CL + 0.3PLB
625.575
+ 0.33TLB299.301
+ 0.33BTB11.236
+ 1SLX +1083.549
0.3SLY + 0.3SLZ
2582.929
+ 1.1NLB
Min Mx 31521 3062 1DL 30577
+ 1SIDL + 0.3CL
-386.75
+ 0.3PLB
-556.379
+ 0.33TLB
-297.124
- 0.33BTB
-13.090
- 1SLX --1195.048
0.3SLY - 0.3SLZ-2211.43
- 1.1NLB
Max My 31521 3047 1DL 30577
+ 1SIDL +8170.462
0.3CL + 0.3PLA
225.942
+ 0.33TLA739.789
+ 0.33BTA6.532
+ 0.3SLX2933.49
+ 0.3SLY + 1SLZ
966.127
+ 1.1NLA
Min My 31521 3054 1DL 30577
+ 1SIDL +-947.711
0.3CL + 0.3PLA
-156.749
+ 0.33TLA
-730.114
- 0.33BTA-8.273
- 0.3SLX -3096.12
- 0.3SLY - 1SLZ
-595.752
- 1.1NLA
Max Mz 31521 1079 1DL 30577
+ 1SIDL +7849.371
0.3CL + 0.3PLA
633.813
+ 0.3PLB295.699
+ 0.33TLA + 10.945
0.33TLB + 1089.335
0.33BTA + 0.33BTB
2615.833
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 31521 1086 1DL 30577
+ 1SIDL +-273.582
0.3CL + 0.3PLA
-564.234
+ 0.3PLB-289.269
+ 0.33TLA +-12.813
0.33TLB - 0.33BTA
-1233.77- 0.33BTB
-2239.514
- 1SLX - 0.3SLY - 0.3SLZ

c) Static LC 1001-1006
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31518 1006 1DL 30574
+ 1SIDL +4920.688
1CL + 1PLA + 1PLB
-45.07+ 1.1TLA
-35.57
+ 1.1TLB --2.255
1.1BTA - 1.1BTB
203.104 -242.084
Min Fx 31518 1003 1DL 30574
+ 1SIDL +3746.686
1CL + 1PLB + 41.146
1.1TLB + -28.728
1.1BTB -0.956 181.618 99.368
Max Fy 31518 1005 1DL 30574
+ 1SIDL +4141.595
1CL + 1PLA + 65.678
1PLB + 1.1TLA
-20.403
+ 1.1TLB +-0.267
1.1BTA + 136.662
1.1BTB 182.012
Min Fy 31518 1006 1DL 30574
+ 1SIDL +4920.688
1CL + 1PLA + 1PLB
-45.07+ 1.1TLA
-35.57
+ 1.1TLB --2.255
1.1BTA - 1.1BTB
203.104 -242.084
Max Fz 31518 1001 1DL 30574
+ 1SIDL +3870.102
1CL + 1PLA + 41.314
1.1TLA + -13.586
1.1BTA -0.337 85.734 98.426
Min Fz 31518 1006 1DL 30574
+ 1SIDL +4920.688
1CL + 1PLA + 1PLB
-45.07+ 1.1TLA
-35.57
+ 1.1TLB --2.255
1.1BTA - 1.1BTB
203.104 -242.084
Max Mx 31518 1005 1DL 30574
+ 1SIDL +4141.595
1CL + 1PLA + 65.678
1PLB + 1.1TLA
-20.403
+ 1.1TLB +-0.267
1.1BTA + 136.662
1.1BTB 182.012
Min Mx 31518 1006 1DL 30574
+ 1SIDL +4920.688
1CL + 1PLA + 1PLB
-45.07+ 1.1TLA
-35.57
+ 1.1TLB --2.255
1.1BTA - 1.1BTB
203.104 -242.084
Max My 31518 1004 1DL 30574
+ 1SIDL + 4121.32
1CL + 1PLB +-14.089
1.1TLB - 1.1BTB
-33.7 -1.545 204.457 -112.033
Min My 31518 1001 1DL 30578
+ 1SIDL +3870.102
1CL + 1PLA + 41.314
1.1TLA + -13.586
1.1BTA -0.337 72.148 57.112
Max Mz 31518 1005 1DL 30574
+ 1SIDL +4141.595
1CL + 1PLA + 65.678
1PLB + 1.1TLA
-20.403
+ 1.1TLB +-0.267
1.1BTA + 136.662
1.1BTB 182.012
Min Mz 31518 1006 1DL 30574
+ 1SIDL +4920.688
1CL + 1PLA + 1PLB
-45.07+ 1.1TLA
-35.57
+ 1.1TLB --2.255
1.1BTA - 1.1BTB
203.104 -242.084
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31519 1005 1DL 30575
+ 1SIDL +5188.017
1CL + 1PLA + 97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB +-0.255
1.1BTA + 149.808
1.1BTB 440.298
Min Fx 31519 1004 1DL 30575
+ 1SIDL +4094.397
1CL + 1PLB + 1.1TLB
13.16 - 1.1BTB
-33.643 -1.503 203.987 111.953
Max Fy 31519 1005 1DL 30575
+ 1SIDL +5188.017
1CL + 1PLA + 97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB +-0.255
1.1BTA + 149.808
1.1BTB 440.298
Min Fy 31519 1006 1DL 30575
+ 1SIDL +4547.937
1CL + 1PLA +-13.463
1PLB + 1.1TLA
-34.998
+ 1.1TLB --2.215
1.1BTA - 1.1BTB
198.443 17.72
Max Fz 31519 1001 1DL 30575
+ 1SIDL +4558.407
1CL + 1PLA + 69.223
1.1TLA + -14.631
1.1BTA -0.336 94.241 327.864
Min Fz 31519 1006 1DL 30575
+ 1SIDL +4547.937
1CL + 1PLA +-13.463
1PLB + 1.1TLA
-34.998
+ 1.1TLB --2.215
1.1BTA - 1.1BTB
198.443 17.72
Max Mx 31519 1005 1DL 30575
+ 1SIDL +5188.017
1CL + 1PLA + 97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB +-0.255
1.1BTA + 149.808
1.1BTB 440.298
Min Mx 31519 1006 1DL 30575
+ 1SIDL +4547.937
1CL + 1PLA +-13.463
1PLB + 1.1TLA
-34.998
+ 1.1TLB --2.215
1.1BTA - 1.1BTB
198.443 17.72
Max My 31519 1004 1DL 30575
+ 1SIDL +4094.397
1CL + 1PLB + 1.1TLB
13.16 - 1.1BTB
-33.643 -1.503 203.987 111.953
Min My 31519 1001 1DL 30579
+ 1SIDL +4558.407
1CL + 1PLA + 69.223
1.1TLA + -14.631
1.1BTA -0.336 79.61 258.641
Max Mz 31519 1005 1DL 30575
+ 1SIDL +5188.017
1CL + 1PLA + 97.098
1PLB + 1.1TLA
-22.016
+ 1.1TLB +-0.255
1.1BTA + 149.808
1.1BTB 440.298
Min Mz 31519 1006 1DL 30575
+ 1SIDL +4547.937
1CL + 1PLA +-13.463
1PLB + 1.1TLA
-34.998
+ 1.1TLB --2.215
1.1BTA - 1.1BTB
198.443 17.72
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31520 1006 1DL 30576
+ 1SIDL +4635.832
1CL + 1PLA +-44.607
1PLB + 1.1TLA
-3.854
+ 1.1TLB --2.316
1.1BTA - 1.1BTB
-57.587 -238.309
Min Fx 31520 1001 1DL 30576
+ 1SIDL +3576.077
1CL + 1PLA + 41.983
1.1TLA + 1.1BTA
12.61 -0.223 -129.703 103.922
Max Fy 31520 1005 1DL 30576
+ 1SIDL +3992.923
1CL + 1PLA + 65.965
1PLB + 1.1TLA
9.117
+ 1.1TLB +-0.099
1.1BTA +-106.136
1.1BTB 184.356
Min Fy 31520 1006 1DL 30576
+ 1SIDL +4635.832
1CL + 1PLA +-44.607
1PLB + 1.1TLA
-3.854
+ 1.1TLB --2.316
1.1BTA - 1.1BTB
-57.587 -238.309
Max Fz 31520 1001 1DL 30576
+ 1SIDL +3576.077
1CL + 1PLA + 41.983
1.1TLA + 1.1BTA
12.61 -0.223 -129.703 103.922
Min Fz 31520 1004 1DL 30576
+ 1SIDL +4050.817
1CL + 1PLB +-14.121
1.1TLB - 1.1BTB
-6.363 -1.546 -20.285 -112.318
Max Mx 31520 1005 1DL 30576
+ 1SIDL +3992.923
1CL + 1PLA + 65.965
1PLB + 1.1TLA
9.117
+ 1.1TLB +-0.099
1.1BTA +-106.136
1.1BTB 184.356
Min Mx 31520 1006 1DL 30576
+ 1SIDL +4635.832
1CL + 1PLA +-44.607
1PLB + 1.1TLA
-3.854
+ 1.1TLB --2.316
1.1BTA - 1.1BTB
-57.587 -238.309
Max My 31520 1004 1DL 30576
+ 1SIDL +4050.817
1CL + 1PLB +-14.121
1.1TLB - 1.1BTB
-6.363 -1.546 -20.285 -112.318
Min My 31520 1001 1DL 30576
+ 1SIDL +3576.077
1CL + 1PLA + 41.983
1.1TLA + 1.1BTA
12.61 -0.223 -129.703 103.922
Max Mz 31520 1005 1DL 30576
+ 1SIDL +3992.923
1CL + 1PLA + 65.965
1PLB + 1.1TLA
9.117
+ 1.1TLB +-0.099
1.1BTA +-106.136
1.1BTB 184.356
Min Mz 31520 1006 1DL 30576
+ 1SIDL +4635.832
1CL + 1PLA +-44.607
1PLB + 1.1TLA
-3.854
+ 1.1TLB --2.316
1.1BTA - 1.1BTB
-57.587 -238.309
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 31521 1005 1DL 30577
+ 1SIDL +5039.345
1CL + 1PLA + 96.812
1PLB + 1.1TLA
10.731
+ 1.1TLB +-0.087
1.1BTA +-119.281
1.1BTB 437.954
Min Fx 31521 1002 1DL 30577
+ 1SIDL +3861.255
1CL + 1PLA + 13.047
1.1TLA - 1.1BTA
3.465 -1.716 -94.648 109.714
Max Fy 31521 1005 1DL 30577
+ 1SIDL +5039.345
1CL + 1PLA + 96.812
1PLB + 1.1TLA
10.731
+ 1.1TLB +-0.087
1.1BTA +-119.281
1.1BTB 437.954
Min Fy 31521 1006 1DL 30577
+ 1SIDL +4263.082
1CL + 1PLA +-13.926
1PLB + 1.1TLA
-4.426
+ 1.1TLB --2.275
1.1BTA - 1.1BTB
-52.927 13.944
Max Fz 31521 1001 1DL 30577
+ 1SIDL +4264.383
1CL + 1PLA + 68.555
1.1TLA + 1.1BTA
13.655 -0.222 -138.21 322.369
Min Fz 31521 1004 1DL 30577
+ 1SIDL +4023.894
1CL + 1PLB + 13.191
1.1TLB - 1.1BTB
-6.42 -1.504 -19.815 112.238
Max Mx 31521 1005 1DL 30577
+ 1SIDL +5039.345
1CL + 1PLA + 96.812
1PLB + 1.1TLA
10.731
+ 1.1TLB +-0.087
1.1BTA +-119.281
1.1BTB 437.954
Min Mx 31521 1006 1DL 30577
+ 1SIDL +4263.082
1CL + 1PLA +-13.926
1PLB + 1.1TLA
-4.426
+ 1.1TLB --2.275
1.1BTA - 1.1BTB
-52.927 13.944
Max My 31521 1004 1DL 30577
+ 1SIDL +4023.894
1CL + 1PLB + 13.191
1.1TLB - 1.1BTB
-6.42 -1.504 -19.815 112.238
Min My 31521 1001 1DL 30577
+ 1SIDL +4264.383
1CL + 1PLA + 68.555
1.1TLA + 1.1BTA
13.655 -0.222 -138.21 322.369
Max Mz 31521 1005 1DL 30577
+ 1SIDL +5039.345
1CL + 1PLA + 96.812
1PLB + 1.1TLA
10.731
+ 1.1TLB +-0.087
1.1BTA +-119.281
1.1BTB 437.954
Min Mz 31521 1006 1DL 30577
+ 1SIDL +4263.082
1CL + 1PLA +-13.926
1PLB + 1.1TLA
-4.426
+ 1.1TLB --2.275
1.1BTA - 1.1BTB
-52.927 13.944

2.2 Pile Loads

MDE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 10201 10696 10170 10327


Min Fx -1846 -1709 -2223 -1753
Max Fy 9377 10696 9701 10101
Min Fy -1102 -1623 -1754 -1356
Max Fz 9872 10193 9899 9890
Min Fz -1455 -1436 -1906 -1557
Max Mx 9377 10696 9701 10101
Min Mx -1102 -1623 -1754 -1356
Max My 9817 10432 9659 9944
Min My -1506 -1480 -1865 -1509
Max Mz 9377 10696 9701 10101
Min Mz -1102 -1623 -1754 -1356
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

ODE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 8338 8708 8296 8444


Min Fx -1204 -1074 -1515 -1122
Max Fy 7541 8257 7646 7849
Min Fy -163 -331 -618 -274
Max Fz 8103 8388 8110 8132
Min Fz -925 -879 -1291 -982
Max Mx 7382 7990 7602 7698
Min Mx -362 -427 -833 -387
Max My 8064 8559 7939 8170
Min My -961 -910 -1262 -948
Max Mz 7541 8257 7646 7849
Min Mz -163 -331 -618 -274

Static
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 4921 5188 4636 5039


Min Fx 3747 4094 3576 3861
Max Fy 4142 5188 3993 5039
Min Fy 4921 4548 4636 4263
Max Fz 3870 4558 3576 4264
Min Fz 4921 4548 4051 4024
Max Mx 4142 5188 3993 5039
Min Mx 4921 4548 4636 4263
Max My 4121 4094 4051 4024
Min My 3870 4558 3576 4264
Max Mz 4142 5188 3993 5039
Min Mz 4921 4548 4636 4263

3.1 Moment at Bottom Face:

Lever arm Z = Pile Centre to column face

Z = 0.80 m

Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or


2.0 m (P1+P2)xZ or (P3+P4)xZ, whichever
column is maximum

P kN
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = 510.276 kN.m
Design Moment, M = M1 - M2

Case M1 (kN.m) M = (M1 - M2) (kN.m)


MDE Seismic 16818.400 16231.582
ODE Seismic 13721.600 13211.324
Static 8181.600 7671.324

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
2
K = Mu/bd fcu = 0.021 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1710.50 mm
Hence, z = 0.95 d = 1624.98 mm
As = Mu / (fy z)
Ast = 25612.358 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


29 120 0 0 0 0

= 28716.101 mm2 OK

3.2 Moment at Top Face:

Lever arm Z = Pile Centre to column face

P kN Z = 0.80 m
2.0 m
column Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or
(P1+P2)xZ or (P3+P4)xZ, whichever
is minimum

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = -510.276 kN.m
Design Moment, M = M1 + M2

Case M1 (kN.m) M = (M1 + M2) (kN.m)


MDE Seismic -3255.200 -3842.018
ODE Seismic -2175.200 -2685.476
Static 0.000 0.000

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

K = Mu/bd2fcu = 0.005 K'


Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.95 d = 1626.88 mm
As = M u / (f y z)
Ast = 6055.368 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 120 0 0 0 0

= 21357.103 mm2 OK

3.3 Moment Capacity, Stress and Crack Width Check from Oasys

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 16230 18370 0.8836 OK
Minima
2 0.0 3843 13770 0.2792 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
43.13 OK
43.13 OK
Minima
-222 OK
-222 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fcu 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Oasys Results
Cocncrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
3 4.753 OK 3 24.57 OK
3 4.753 OK 3 24.57 OK
Minima Minima
3 -0.5873 OK 3 -107.4 OK
3 -0.5873 OK 3 -107.4 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.179 mm OK

3.4 Minimum Reinforcement


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4007.25 mm2/m
2
At bottom face, Provided = 5418 mm2/m
Astprovided > Astmin OK
At top face, Provided = 4030 mm2/m
Astprovided > Astmin OK

4.0 Shear Check


Total pile reaction, V1 = 21023 kN
As per Cl. 3.11.4.3, pg. 82, BS 8110-1: 1997, critical section for shear should be located 20% of the pile diameter inside
Distance of critical section for shear check from column face = 0.440 m
Factored weight per unit length due to soil and pile cap = 431.087 kN/m
Hence, downward reaction due to soil and pile cap weight,
V2 = weight per unit length x (length of pile cap - 0.5 x column size - distance of critical section)
V2 = 522 kN
Net reaction, Vu = V1 - V2 = 20501 kN
Width of pile cap available b = 5.300 m
Effective depth of pile cap d = 1.711 m
Area of tensile steel provided As = 28716 mm2
= 0.029 m2
Percentage of tensile steel provided 100As/(b.d) = 0.317 %
Shear stress = Vu /(b.d) = 2261.44 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.35 MPa
= 350 kN/sqm
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Rahul
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

As per Cl. 3.11.4.4, pg. 82, BS 8110-1:1997,


Enhanced shear strength of concrete, say vc,1 = 2.d.vc /av
av = 0.440 m
Therefore, vc,1 = 2.72 MPa
= 2721 kN/sqm
Vus = Vu - vc,1 b d = -4168.52 kN

Requirement of shear reinforcement = Not Required

5.0 Check for punching shear


Total pile load = 41394 kN
From section 1.0 above, factored weight of pile cap + earthfill = 1987 kN
Hence, net punching shear force = 39407 kN
Effective depth of pile cap = 1.711 m
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, punching shear shall be checked at the perimeter of the column.
Shear perimeter = 8.000 m
Shearing Area = 13.684 m2
Punching Shear stress = 2879.805 kN/m2
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997,
Allowable punching shear stress = lesser of 0.8 fcu or 5 N/mm2 = 5.00 N/mm2
= 5000.000 kN/m2
OK
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, since the pile spacing is not greater than 3 times the pile diameter, no
additional punching shear check is required.
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR COLUMN C34


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Column No. = C34

No. of piles n = 4
Dia of pile = 1.20 m
Size of Column = 2.00 m x 2.00 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 5.30 m x 5.30 m


2
Area of pile cap = 28.09 m
Depth of pile cap D = 1.80 m
Volume of pile cap = 50.56 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 1264.05 kN

Thickness of Earthfill over pile cap = 1.50 m


Volume of Earthfill over pile cap = 36.14 m3
Density of Earth = 20 kN/cum
Weight of Earthfill = 722.70 kN

Total weight of (Pile cap + Earthfill) = 1986.75 kN

2.0 PILE LOADS

2.1 Summary of Staad Results (Forces at Bottom of Pile Cap)---

LC 1303-1326, 1427-1466, 1567-1590, 2101-2202, 2331-


a) MDE Seismic
2378, 3131-3178,4101-4132, 5109-5124 & 6109-6124
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30338 2202 1.15DL
29386
+ 1.2SIDL
9650.936
+ 0.42CL 222.918
+ 0.42PLA +927.238
0.42PLB + 0.462TLA
8.276 + 0.462TLB
3018.474 - 0.462BTA
644.668- 0.462BTB - 0.3SLX - 0.3SLY
Min Fx 30338 2115 1.15DL
29386
+ 1.2SIDL
-2252.13
+ 0.3SLX +-211.04
0.3SLY + 1SLZ
-969.974 -11.106 -2817.672 -703.209
Max Fy 30338 2103 1.15DL
29382
+ 1.2SIDL
8710.556
+ 1.4CL 1169.978
+ 1.4PLB + 1.54TLB
182.165+ 1.54BTB
17.927 903.491 4681.51
Min Fy 30338 2104 1.15DL
29386
+ 1.2SIDL
-1535.72
+ 1.4CL-1111.808
+ 1.4PLB + -224.039
1.54TLB - 1.54BTB
-21.885 -486.482 -3432.065
Max Fz 30338 3171 1.15DL
29382
+ 1.2SIDL
9113.354
+ 0.42CL 257.318
+ 0.42PLB +943.613
0.462TLB +9.474
0.462BTB
3931.858
+ 0.3SLX + 0.3SLY
998.721+ 1SLZ + 1.54NLB
Min Fz 30338 3178 1.15DL
29382
+ 1.2SIDL
-1888.47
+ 0.42CL-220.017
+ 0.42PLB + -983.62
0.462TLB-12.311
- 0.462BTB
-3689.806
- 0.3SLX - 0.3SLY
-948.755
- 1SLZ - 1.54NLB
Max Mx 30338 2103 1.15DL
29382
+ 1.2SIDL
8710.556
+ 1.4CL 1169.978
+ 1.4PLB + 1.54TLB
182.165+ 1.54BTB
17.927 903.491 4681.51
Min Mx 30338 2104 1.15DL
29386
+ 1.2SIDL
-1535.72
+ 1.4CL-1111.808
+ 1.4PLB + -224.039
1.54TLB - 1.54BTB
-21.885 -486.482 -3432.065
Max My 30338 3147 1.15DL
29382
+ 1.2SIDL
9306.689
+ 0.42CL 256.698
+ 0.42PLA +924.028
0.462TLA + 8.392
0.462BTA3995.702
+ 0.3SLX + 0.3SLY
994.745+ 1SLZ + 1.54NLA
Min My 30338 3154 1.15DL
29382
+ 1.2SIDL
-1970.19
+ 0.42CL-219.216
+ 0.42PLA +-962.048
0.462TLA --10.554
0.462BTA-3782.327
- 0.3SLX - 0.3SLY
-945.174
- 1SLZ - 1.54NLA
Max Mz 30338 2103 1.15DL
29382
+ 1.2SIDL
8710.556
+ 1.4CL 1169.978
+ 1.4PLB + 1.54TLB
182.165+ 1.54BTB
17.927 903.491 4681.51
Min Mz 30338 2104 1.15DL
29386
+ 1.2SIDL
-1535.72
+ 1.4CL-1111.808
+ 1.4PLB + -224.039
1.54TLB - 1.54BTB
-21.885 -486.482 -3432.065
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL 1196.044
+ 1.4PLB + 1.54TLB
183.031+ 1.54BTB
17.560 931.72 4895.634
Min Fx 30339 2104 1.15DL
29387
+ 1.2SIDL
-2333.95
+ 1.4CL-1089.362
+ 1.4PLB + -225.934
1.54TLB - 1.54BTB
-21.480 -503.826 -3269.828
Max Fy 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL 1196.044
+ 1.4PLB + 1.54TLB
183.031+ 1.54BTB
17.560 931.72 4895.634
Min Fy 30339 2104 1.15DL
29387
+ 1.2SIDL
-2333.95
+ 1.4CL-1089.362
+ 1.4PLB + -225.934
1.54TLB - 1.54BTB
-21.480 -503.826 -3269.828
Max Fz 30339 3171 1.15DL
29383
+ 1.2SIDL
9788.785
+ 0.42CL 289.335
+ 0.42PLB +943.429
0.462TLB +9.056
0.462BTB3941.25
+ 0.3SLX + 1248.536
0.3SLY + 1SLZ + 1.54NLB
Min Fz 30339 3178 1.15DL
29383
+ 1.2SIDL
-1939.45
+ 0.42CL-203.621
+ 0.42PLB +-984.298
0.462TLB-11.860
- 0.462BTB
-3692.205
- 0.3SLX - 0.3SLY
-800.608
- 1SLZ - 1.54NLB
Max Mx 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL 1196.044
+ 1.4PLB + 1.54TLB
183.031+ 1.54BTB
17.560 931.72 4895.634
Min Mx 30339 2104 1.15DL
29387
+ 1.2SIDL
-2333.95
+ 1.4CL-1089.362
+ 1.4PLB + -225.934
1.54TLB - 1.54BTB
-21.480 -503.826 -3269.828
Max My 30339 3147 1.15DL
29383
+ 1.2SIDL
9979.791
+ 0.42CL 289.404
+ 0.42PLA +923.846
0.462TLA + 8.014
0.462BTA4005.073
+ 0.3SLX +1250.205
0.3SLY + 1SLZ + 1.54NLA
Min My 30339 3154 1.15DL
29383
+ 1.2SIDL
-2014.32
+ 0.42CL-202.972
+ 0.42PLA +-962.734
0.462TLA --10.147
0.462BTA-3784.656
- 0.3SLX - 0.3SLY
-798.239
- 1SLZ - 1.54NLA
Max Mz 30339 2103 1.15DL
29383
+ 1.2SIDL
10293.99
+ 1.4CL 1196.044
+ 1.4PLB + 1.54TLB
183.031+ 1.54BTB
17.560 931.72 4895.634
Min Mz 30339 2104 1.15DL
29387
+ 1.2SIDL
-2333.95
+ 1.4CL-1089.362
+ 1.4PLB + -225.934
1.54TLB - 1.54BTB
-21.480 -503.826 -3269.828
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30340 2202 1.15DL
29388
+ 1.2SIDL
9481.563
+ 0.42CL 231.268
+ 0.42PLA +952.978
0.42PLB + 0.462TLA
8.388 + 0.462TLB
2839.895 - 0.462BTA
689.481- 0.462BTB - 0.3SLX - 0.3SLY
Min Fx 30340 2115 1.15DL
29388
+ 1.2SIDL
-2607.59
+ 0.3SLX-218.375
+ 0.3SLY + 1SLZ
-948.849 -11.146 -2977.555 -740.725
Max Fy 30340 2103 1.15DL
29384
+ 1.2SIDL
8853.004
+ 1.4CL 1170.858
+ 1.4PLB + 1.54TLB
206.666+ 1.54BTB
18.570 733.089 4688.673
Min Fy 30340 2104 1.15DL
29388
+ 1.2SIDL
-2133.44
+ 1.4CL-1111.826
+ 1.4PLB + -201.934
1.54TLB - 1.54BTB
-22.360 -673.229 -3432.142
Max Fz 30340 3171 1.15DL
29384
+ 1.2SIDL
9209.668
+ 0.42CL 265.208
+ 0.42PLB +967.315
0.462TLB +9.655
0.462BTB
3745.307
+ 0.3SLX + 1050.173
0.3SLY + 1SLZ + 1.54NLB
Min Fz 30340 3178 1.15DL
29384
+ 1.2SIDL
-2365.92
+ 0.42CL-227.194
+ 0.42PLB +-960.498
0.462TLB-12.367
- 0.462BTB
-3888.277
- 0.3SLX - 0.3SLY
-994.379
- 1SLZ - 1.54NLB
Max Mx 30340 2103 1.15DL
29384
+ 1.2SIDL
8853.004
+ 1.4CL 1170.858
+ 1.4PLB + 1.54TLB
206.666+ 1.54BTB
18.570 733.089 4688.673
Min Mx 30340 2104 1.15DL
29388
+ 1.2SIDL
-2133.44
+ 1.4CL-1111.826
+ 1.4PLB + -201.934
1.54TLB - 1.54BTB
-22.360 -673.229 -3432.142
Max My 30340 3147 1.15DL
29384
+ 1.2SIDL
9018.068
+ 0.42CL 265.279
+ 0.42PLA + 947.73
0.462TLA + 8.573
0.462BTA3809.147
+ 0.3SLX +1051.855
0.3SLY + 1SLZ + 1.54NLA
Min My 30340 3154 1.15DL
29384
+ 1.2SIDL
-2291.33
+ 0.42CL-226.544
+ 0.42PLA +-938.936
0.462TLA --10.609
0.462BTA-3980.719
- 0.3SLX - 0.3SLY
-991.998
- 1SLZ - 1.54NLA
Max Mz 30340 2103 1.15DL
29384
+ 1.2SIDL
8853.004
+ 1.4CL 1170.858
+ 1.4PLB + 1.54TLB
206.666+ 1.54BTB
18.570 733.089 4688.673
Min Mz 30340 2104 1.15DL
29388
+ 1.2SIDL
-2133.44
+ 1.4CL-1111.826
+ 1.4PLB + -201.934
1.54TLB - 1.54BTB
-22.360 -673.229 -3432.142
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30341 2195 1.15DL
29385
+ 1.2SIDL
9777.739
+ 0.42CL 291.318
+ 0.42PLA +961.113
0.42PLB + 0.462TLA
8.882 + 0.462TLB
3749.71 + 0.462BTA
1234.423+ 0.462BTB + 0.3SLX + 0.3S
Min Fx 30341 2104 1.15DL
29389
+ 1.2SIDL
-2268.43
+ 1.4CL-1089.345
+ 1.4PLB + -200.146
1.54TLB - 1.54BTB
-21.972 -657.609 -3269.755
Max Fy 30341 2103 1.15DL
29385
+ 1.2SIDL
9773.217
+ 1.4CL 1195.164
+ 1.4PLB + 1.54TLB
205.906+ 1.54BTB
18.221 706.554 4888.467
Min Fy 30341 2104 1.15DL
29389
+ 1.2SIDL
-2268.43
+ 1.4CL-1089.345
+ 1.4PLB + -200.146
1.54TLB - 1.54BTB
-21.972 -657.609 -3269.755
Max Fz 30341 3171 1.15DL
29385
+ 1.2SIDL
9605.008
+ 0.42CL 281.439
+ 0.42PLB +967.533
0.462TLB +9.247
0.462BTB
3736.262
+ 0.3SLX + 1197.067
0.3SLY + 1SLZ + 1.54NLB
Min Fz 30341 3178 1.15DL
29385
+ 1.2SIDL
-2136.8
+ 0.42CL-196.439
+ 0.42PLB +-959.856
0.462TLB-11.924
- 0.462BTB
-3886.223
- 0.3SLX - 0.3SLY
-754.976
- 1SLZ - 1.54NLB
Max Mx 30341 2103 1.15DL
29385
+ 1.2SIDL
9773.217
+ 1.4CL 1195.164
+ 1.4PLB + 1.54TLB
205.906+ 1.54BTB
18.221 706.554 4888.467
Min Mx 30341 2104 1.15DL
29389
+ 1.2SIDL
-2268.43
+ 1.4CL-1089.345
+ 1.4PLB + -200.146
1.54TLB - 1.54BTB
-21.972 -657.609 -3269.755
Max My 30341 3147 1.15DL
29385
+ 1.2SIDL
9411.098
+ 0.42CL 280.816
+ 0.42PLA +947.946
0.462TLA + 8.205
0.462BTA3800.125
+ 0.3SLX +1193.068
0.3SLY + 1SLZ + 1.54NLA
Min My 30341 3154 1.15DL
29385
+ 1.2SIDL
-2055.36
+ 0.42CL-195.639
+ 0.42PLA +-938.285
0.462TLA --10.210
0.462BTA-3978.736
- 0.3SLX - 0.3SLY
-751.401
- 1SLZ - 1.54NLA
Max Mz 30341 2103 1.15DL
29385
+ 1.2SIDL
9773.217
+ 1.4CL 1195.164
+ 1.4PLB + 1.54TLB
205.906+ 1.54BTB
18.221 706.554 4888.467
Min Mz 30341 2104 1.15DL
29389
+ 1.2SIDL
-2268.43
+ 1.4CL-1089.345
+ 1.4PLB + -200.146
1.54TLB - 1.54BTB
-21.972 -657.609 -3269.755
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

LC 1001-1190, 2031-2078, 3031-3078, 4001-


b) ODE Seismic
4032, 5009-5024 & 6009-6024
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30338 1102 1DL 29386
+ 1SIDL +7869.774
0.3CL + 0.3PLA
180.803
+ 0.3PLB737.998
+ 0.33TLA + 0.33TLB
6.568 - 0.33BTA
2410.631- 0.33BTB
521.122
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 30338 1015 1DL 29386
+ 1SIDL + 0.3SLX
-1563.8+ 0.3SLY
-166.903
+ 1SLZ -774.221 -8.938 -2240.048 -560.325
Max Fy 30338 1079 1DL 29382
+ 1SIDL +7026.846
0.3CL + 0.3PLA
606.553
+ 0.3PLB308.092
+ 0.33TLA + 10.804
0.33TLB + 1393.476
0.33BTA + 0.33BTB
2413.601
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30338 1086 1DL 29382
+ 1SIDL +-533.946
0.3CL + 0.3PLA
-577.19
+ 0.3PLB -341.89
+ 0.33TLA +-13.020
0.33TLB - -1194.936
0.33BTA - 0.33BTB
-2387.198
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30338 3071 1DL 29382
+ 1SIDL +7485.788
0.3CL + 0.3PLB
205.375
+ 0.33TLB749.695
+ 0.33BTB7.424
+ 0.3SLX3144.372
+ 0.3SLY + 1SLZ
795.388
+ 1.1NLB
Min Fz 30338 3078 1DL 29382
+ 1SIDL +-1304.04
0.3CL + 0.3PLB
-173.314
+ 0.33TLB
-783.968
- 0.33BTB-9.799
- 0.3SLX-2938.627
- 0.3SLY - 1SLZ-751.67
- 1.1NLB
Max Mx 30338 3055 1DL 29382
+ 1SIDL +6881.915
0.3CL + 0.3PLB
600.495
+ 0.33TLB313.676
+ 0.33BTB11.089
+ 1SLX + 1375.67
0.3SLY + 0.3SLZ
2395.121
+ 1.1NLB
Min Mx 30338 3062 1DL 29382
+ 1SIDL +-700.164
0.3CL + 0.3PLB
-568.435
+ 0.33TLB
-347.949
- 0.33BTB
-13.464
- 1SLX --1169.926
0.3SLY - 0.3SLZ
-2351.403
- 1.1NLB
Max My 30338 3047 1DL 29382
+ 1SIDL +7623.885
0.3CL + 0.3PLA
204.932
+ 0.33TLA735.706
+ 0.33BTA6.651
+ 0.3SLX 3189.974
+ 0.3SLY + 1SLZ
792.548
+ 1.1NLA
Min My 30338 3054 1DL 29382
+ 1SIDL +-1362.41
0.3CL + 0.3PLA
-172.743
+ 0.33TLA
-768.559
- 0.33BTA-8.544
- 0.3SLX-3004.714
- 0.3SLY - 1SLZ
-749.113
- 1.1NLA
Max Mz 30338 1079 1DL 29382
+ 1SIDL +7026.846
0.3CL + 0.3PLA
606.553
+ 0.3PLB308.092
+ 0.33TLA + 10.804
0.33TLB + 1393.476
0.33BTA + 0.33BTB
2413.601
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30338 1086 1DL 29382
+ 1SIDL +-533.946
0.3CL + 0.3PLA
-577.19
+ 0.3PLB -341.89
+ 0.33TLA +-13.020
0.33TLB - -1194.936
0.33BTA - 0.33BTB
-2387.198
- 1SLX - 0.3SLY - 0.3SLZ
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30339 1095 1DL 29383
+ 1SIDL + 8283.47
0.3CL + 0.3PLA
239.545
+ 0.3PLB743.771
+ 0.33TLA + 0.33TLB
6.819 + 3171.188
0.33BTA + 0.33BTB
1034.292
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 30339 1015 1DL 29387
+ 1SIDL +-1485.84
0.3SLX + 0.3SLY
-153.863
+ 1SLZ -774.948 -8.596 -2240.321 -453.877
Max Fy 30339 1079 1DL 29383
+ 1SIDL +7887.372
0.3CL + 0.3PLA
631.035
+ 0.3PLB308.488
+ 0.33TLA + 10.536
0.33TLB + 1408.363
0.33BTA + 0.33BTB
2611.575
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30339 1086 1DL 29383
+ 1SIDL +-855.447
0.3CL + 0.3PLA
-558.165
+ 0.3PLB -343.05
+ 0.33TLA +-12.725
0.33TLB - -1203.622
0.33BTA - 0.33BTB
-2227.523
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30339 3071 1DL 29383
+ 1SIDL +8029.213
0.3CL + 0.3PLB
232.239
+ 0.33TLB749.542
+ 0.33BTB7.093
+ 0.3SLX3151.859
+ 0.3SLY + 1SLZ
1005.563
+ 1.1NLB
Min Fz 30339 3078 1DL 29383
+ 1SIDL +-1313.84
0.3CL + 0.3PLB
-158.88
+ 0.33TLB
-784.549
- 0.33BTB-9.438
- 0.3SLX-2940.151
- 0.3SLY - 1SLZ
-622.354
- 1.1NLB
Max Mx 30339 3055 1DL 29383
+ 1SIDL +7633.114
0.3CL + 0.3PLB
623.73
+ 0.33TLB314.259
+ 0.33BTB10.810
+ 1SLX +1389.034
0.3SLY + 0.3SLZ
2582.847
+ 1.1NLB
Min Mx 30339 3062 1DL 29383
+ 1SIDL +-917.742
0.3CL + 0.3PLB
-550.371
+ 0.33TLB
-349.266
- 0.33BTB
-13.155
- 1SLX --1177.325
0.3SLY - 0.3SLZ
-2199.637
- 1.1NLB
Max My 30339 3047 1DL 29383
+ 1SIDL +8165.646
0.3CL + 0.3PLA
232.289
+ 0.33TLA735.554
+ 0.33BTA6.349
+ 0.3SLX 3197.447
+ 0.3SLY + 1SLZ
1006.755
+ 1.1NLA
Min My 30339 3054 1DL 29383
+ 1SIDL +-1367.32
0.3CL + 0.3PLA
-158.416
+ 0.33TLA
-769.147
- 0.33BTA-8.215
- 0.3SLX-3006.188
- 0.3SLY - 1SLZ
-620.661
- 1.1NLA
Max Mz 30339 1079 1DL 29383
+ 1SIDL +7887.372
0.3CL + 0.3PLA
631.035
+ 0.3PLB308.488
+ 0.33TLA + 10.536
0.33TLB + 1408.363
0.33BTA + 0.33BTB
2611.575
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30339 1086 1DL 29383
+ 1SIDL +-855.447
0.3CL + 0.3PLA
-558.165
+ 0.3PLB -343.05
+ 0.33TLA +-12.725
0.33TLB - -1203.622
0.33BTA - 0.33BTB
-2227.523
- 1SLX - 0.3SLY - 0.3SLZ
Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30340 1102 1DL 29388
+ 1SIDL +7724.206
0.3CL + 0.3PLA
187.451
+ 0.3PLB759.659
+ 0.33TLA + 0.33TLB
6.665 - 0.33BTA
2260.038- 0.33BTB
556.799
- 0.3SLX - 0.3SLY - 1SLZ
Min Fx 30340 1015 1DL 29388
+ 1SIDL +-1862.74
0.3SLX + 0.3SLY
-172.69
+ 1SLZ -755.944 -8.965 -2377.889 -589.815
Max Fy 30340 1079 1DL 29384
+ 1SIDL +7018.779
0.3CL + 0.3PLA
609.028
+ 0.3PLB329.759
+ 0.33TLA + 11.137
0.33TLB + 1232.349
0.33BTA + 0.33BTB
2430.693
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30340 1086 1DL 29384
+ 1SIDL +-965.669
0.3CL + 0.3PLA
-578.782
+ 0.3PLB-321.708
+ 0.33TLA +-13.248
0.33TLB - -1377.918
0.33BTA - 0.33BTB
-2397.059
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30340 3071 1DL 29384
+ 1SIDL +7529.995
0.3CL + 0.3PLB
211.694
+ 0.33TLB769.9
+ 0.33BTB7.571
+ 0.3SLX2984.898
+ 0.3SLY + 1SLZ
836.647
+ 1.1NLB
Min Fz 30340 3078 1DL 29384
+ 1SIDL +-1690.12
0.3CL + 0.3PLB
-178.989
+ 0.33TLB
-764.265
- 0.33BTB-9.837
- 0.3SLX-3107.308
- 0.3SLY - 1SLZ
-787.655
- 1.1NLB
Max Mx 30340 3055 1DL 29384
+ 1SIDL +7004.733
0.3CL + 0.3PLB
602.72
+ 0.33TLB334.531
+ 0.33BTB11.408
+ 1SLX +1221.221
0.3SLY + 0.3SLZ
2410.17
+ 1.1NLB
Min Mx 30340 3062 1DL 29384
+ 1SIDL +-1164.86
0.3CL + 0.3PLB
-570.015
+ 0.33TLB
-328.896
- 0.33BTB
-13.675
- 1SLX --1343.631
0.3SLY - 0.3SLZ
-2361.178
- 1.1NLB
Max My 30340 3047 1DL 29384
+ 1SIDL +7393.137
0.3CL + 0.3PLA
211.745
+ 0.33TLA755.911
+ 0.33BTA6.797
+ 0.3SLX 3030.498
+ 0.3SLY + 1SLZ
837.849
+ 1.1NLA
Min My 30340 3054 1DL 29384
+ 1SIDL +-1636.84
0.3CL + 0.3PLA
-178.525
+ 0.33TLA
-748.863
- 0.33BTA-8.581
- 0.3SLX-3173.338
- 0.3SLY - 1SLZ
-785.955
- 1.1NLA
Max Mz 30340 1079 1DL 29384
+ 1SIDL +7018.779
0.3CL + 0.3PLA
609.028
+ 0.3PLB329.759
+ 0.33TLA + 11.137
0.33TLB + 1232.349
0.33BTA + 0.33BTB
2430.693
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30340 1086 1DL 29384
+ 1SIDL +-965.669
0.3CL + 0.3PLA
-578.782
+ 0.3PLB-321.708
+ 0.33TLA +-13.248
0.33TLB - -1377.918
0.33BTA - 0.33BTB
-2397.059
- 1SLX - 0.3SLY - 0.3SLZ
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30341 1095 1DL 29385
+ 1SIDL +7973.774
0.3CL + 0.3PLA
232.971
+ 0.3PLB765.495
+ 0.33TLA + 0.33TLB
6.986 + 2987.293
0.33BTA + 0.33BTB990.97
+ 0.3SLX + 0.3SLY + 1SLZ
Min Fx 30341 1015 1DL 29389
+ 1SIDL +-1561.75
0.3SLX + 0.3SLY
-148.071
+ 1SLZ -755.246 -8.630 -2377.885 -424.384
Max Fy 30341 1079 1DL 29385
+ 1SIDL +7497.825
0.3CL + 0.3PLA
628.559
+ 0.3PLB +329.42
0.33TLA + 10.879
0.33TLB + 1218.337
0.33BTA + 0.33BTB
2594.464
+ 1SLX + 0.3SLY + 0.3SLZ
Min Fy 30341 1086 1DL 29385
+ 1SIDL +-905.671
0.3CL + 0.3PLA
-556.571
+ 0.3PLB-320.606
+ 0.33TLA +-12.964
0.33TLB - -1370.104
0.33BTA - 0.33BTB
-2217.651
- 1SLX - 0.3SLY - 0.3SLZ
Max Fz 30341 3071 1DL 29385
+ 1SIDL +7850.396
0.3CL + 0.3PLB
225.916
+ 0.33TLB770.081
+ 0.33BTB7.247
+ 0.3SLX2977.688
+ 0.3SLY + 1SLZ
964.288
+ 1.1NLB
Min Fz 30341 3078 1DL 29385
+ 1SIDL +-1476.88
0.3CL + 0.3PLB
-153.201
+ 0.33TLB
-763.712
- 0.33BTB-9.484
- 0.3SLX-3106.059
- 0.3SLY - 1SLZ
-586.359
- 1.1NLB
Max Mx 30341 3055 1DL 29385
+ 1SIDL +7374.447
0.3CL + 0.3PLB
621.503
+ 0.33TLB334.006
+ 0.33BTB11.140
+ 1SLX +1208.732
0.3SLY + 0.3SLZ
2567.781
+ 1.1NLB
Min Mx 30341 3062 1DL 29385
+ 1SIDL +-1000.94
0.3CL + 0.3PLB
-548.788
+ 0.33TLB
-327.637
- 0.33BTB
-13.377
- 1SLX --1337.104
0.3SLY - 0.3SLZ
-2189.853
- 1.1NLB
Max My 30341 3047 1DL 29385
+ 1SIDL +7711.888
0.3CL + 0.3PLA
225.47
+ 0.33TLA 756.09
+ 0.33BTA6.502
+ 0.3SLX 3023.303
+ 0.3SLY + 1SLZ
961.431
+ 1.1NLA
Min My 30341 3054 1DL 29385
+ 1SIDL +-1418.72
0.3CL + 0.3PLA
-152.63
+ 0.33TLA
-748.304
- 0.33BTA-8.259
- 0.3SLX -3172.14
- 0.3SLY - 1SLZ
-583.806
- 1.1NLA
Max Mz 30341 1079 1DL 29385
+ 1SIDL +7497.825
0.3CL + 0.3PLA
628.559
+ 0.3PLB +329.42
0.33TLA + 10.879
0.33TLB + 1218.337
0.33BTA + 0.33BTB
2594.464
+ 1SLX + 0.3SLY + 0.3SLZ
Min Mz 30341 1086 1DL 29385
+ 1SIDL +-905.671
0.3CL + 0.3PLA
-556.571
+ 0.3PLB-320.606
+ 0.33TLA +-12.964
0.33TLB - -1370.104
0.33BTA - 0.33BTB
-2217.651
- 1SLX - 0.3SLY - 0.3SLZ

c) Static LC 1001-1006
Pile 1
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30338 1006 1DL 29382
+ 1SIDL +4359.919
1CL + 1PLA +-36.022
1PLB + 1.1TLA
-28.561
+ 1.1TLB --2.367
1.1BTA - 1.1BTB
153.81 -188.831
Min Fx 30338 1003 1DL 29382
+ 1SIDL + 3254.64
1CL + 1PLB + 44.977
1.1TLB + -15.732
1.1BTB -1.417 107.031 124.395
Max Fy 30338 1005 1DL 29382
+ 1SIDL +3563.067
1CL + 1PLA + 66.076
1PLB + 1.1TLA
-8.185
+ 1.1TLB +-0.464
1.1BTA + 1.1BTB
66.955 190.792
Min Fy 30338 1006 1DL 29382
+ 1SIDL +4359.919
1CL + 1PLA +-36.022
1PLB + 1.1TLA
-28.561
+ 1.1TLB --2.367
1.1BTA - 1.1BTB
153.81 -188.831
Max Fz 30338 1005 1DL 29382
+ 1SIDL +3563.067
1CL + 1PLA + 66.076
1PLB + 1.1TLA
-8.185
+ 1.1TLB +-0.464
1.1BTA + 1.1BTB
66.955 190.792
Min Fz 30338 1006 1DL 29382
+ 1SIDL +4359.919
1CL + 1PLA +-36.022
1PLB + 1.1TLA
-28.561
+ 1.1TLB --2.367
1.1BTA - 1.1BTB
153.81 -188.831
Max Mx 30338 1001 1DL 29382
+ 1SIDL + 3365.63
1CL + 1PLA + 45.331
1.1TLA + -10.044
1.1BTA -0.187 60.181 124.623
Min Mx 30338 1006 1DL 29382
+ 1SIDL +4359.919
1CL + 1PLA +-36.022
1PLB + 1.1TLA
-28.561
+ 1.1TLB --2.367
1.1BTA - 1.1BTB
153.81 -188.831
Max My 30338 1006 1DL 29382
+ 1SIDL +4359.919
1CL + 1PLA +-36.022
1PLB + 1.1TLA
-28.561
+ 1.1TLB --2.367
1.1BTA - 1.1BTB
153.81 -188.831
Min My 30338 1001 1DL 29386
+ 1SIDL + 3365.63
1CL + 1PLA + 45.331
1.1TLA + -10.044
1.1BTA -0.187 50.137 79.291
Max Mz 30338 1005 1DL 29382
+ 1SIDL +3563.067
1CL + 1PLA + 66.076
1PLB + 1.1TLA
-8.185
+ 1.1TLB +-0.464
1.1BTA + 1.1BTB
66.955 190.792
Min Mz 30338 1006 1DL 29382
+ 1SIDL +4359.919
1CL + 1PLA +-36.022
1PLB + 1.1TLA
-28.561
+ 1.1TLB --2.367
1.1BTA - 1.1BTB
153.81 -188.831
Pile 2
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30339 1005 1DL 29383
+ 1SIDL +4612.376
1CL + 1PLA + 93.247
1PLB + 1.1TLA-9.834
+ 1.1TLB +-0.473
1.1BTA + 1.1BTB
80.393 414.166
Min Fx 30339 1004 1DL 29383
+ 1SIDL +3589.351
1CL + 1PLB + 17.594
1.1TLB - 1.1BTB
-22.457 -1.920 136.585 128.672
Max Fy 30339 1005 1DL 29383
+ 1SIDL +4612.376
1CL + 1PLA + 93.247
1PLB + 1.1TLA-9.834
+ 1.1TLB +-0.473
1.1BTA + 1.1BTB
80.393 414.166
Min Fy 30339 1006 1DL 29383
+ 1SIDL +3965.632
1CL + 1PLA + 1PLB
-8.76+ 1.1TLA
-27.887
+ 1.1TLB --2.336
1.1BTA - 1.1BTB
148.297 35.27
Max Fz 30339 1005 1DL 29383
+ 1SIDL +4612.376
1CL + 1PLA + 93.247
1PLB + 1.1TLA-9.834
+ 1.1TLB +-0.473
1.1BTA + 1.1BTB
80.393 414.166
Min Fz 30339 1006 1DL 29383
+ 1SIDL +3965.632
1CL + 1PLA + 1PLB
-8.76+ 1.1TLA
-27.887
+ 1.1TLB --2.336
1.1BTA - 1.1BTB
148.297 35.27
Max Mx 30339 1001 1DL 29383
+ 1SIDL +4050.981
1CL + 1PLA + 69.453
1.1TLA + -11.072
1.1BTA -0.190 68.551 322.927
Min Mx 30339 1006 1DL 29383
+ 1SIDL +3965.632
1CL + 1PLA + 1PLB
-8.76+ 1.1TLA
-27.887
+ 1.1TLB --2.336
1.1BTA - 1.1BTB
148.297 35.27
Max My 30339 1006 1DL 29383
+ 1SIDL +3965.632
1CL + 1PLA + 1PLB
-8.76+ 1.1TLA
-27.887
+ 1.1TLB --2.336
1.1BTA - 1.1BTB
148.297 35.27
Min My 30339 1001 1DL 29387
+ 1SIDL +4050.981
1CL + 1PLA + 69.453
1.1TLA + -11.072
1.1BTA -0.190 57.479 253.474
Max Mz 30339 1005 1DL 29383
+ 1SIDL +4612.376
1CL + 1PLA + 93.247
1PLB + 1.1TLA-9.834
+ 1.1TLB +-0.473
1.1BTA + 1.1BTB
80.393 414.166
Min Mz 30339 1006 1DL 29383
+ 1SIDL +3965.632
1CL + 1PLA + 1PLB
-8.76+ 1.1TLA
-27.887
+ 1.1TLB --2.336
1.1BTA - 1.1BTB
148.297 35.27
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Pile 3
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30340 1006 1DL 29384
+ 1SIDL +3984.184
1CL + 1PLA +-35.307
1PLB + 1.1TLA-1.35
+ 1.1TLB --2.413
1.1BTA - 1.1BTB
-69.863 -182.972
Min Fx 30340 1001 1DL 29384
+ 1SIDL +3049.483
1CL + 1PLA + 46.065
1.1TLA + 1.1BTA
12.309 -0.070 -123.659 130.658
Max Fy 30340 1005 1DL 29384
+ 1SIDL +3383.634
1CL + 1PLA + 66.529
1PLB + 1.1TLA
16.877
+ 1.1TLB +-0.301
1.1BTA + 1.1BTB
-139.19 194.517
Min Fy 30340 1006 1DL 29384
+ 1SIDL +3984.184
1CL + 1PLA +-35.307
1PLB + 1.1TLA-1.35
+ 1.1TLB --2.413
1.1BTA - 1.1BTB
-69.863 -182.972
Max Fz 30340 1005 1DL 29384
+ 1SIDL +3383.634
1CL + 1PLA + 66.529
1PLB + 1.1TLA
16.877
+ 1.1TLB +-0.301
1.1BTA + 1.1BTB
-139.19 194.517
Min Fz 30340 1006 1DL 29384
+ 1SIDL +3984.184
1CL + 1PLA +-35.307
1PLB + 1.1TLA-1.35
+ 1.1TLB --2.413
1.1BTA - 1.1BTB
-69.863 -182.972
Max Mx 30340 1001 1DL 29384
+ 1SIDL +3049.483
1CL + 1PLA + 46.065
1.1TLA + 1.1BTA
12.309 -0.070 -123.659 130.658
Min Mx 30340 1006 1DL 29384
+ 1SIDL +3984.184
1CL + 1PLA +-35.307
1PLB + 1.1TLA-1.35
+ 1.1TLB --2.413
1.1BTA - 1.1BTB
-69.863 -182.972
Max My 30340 1004 1DL 29388
+ 1SIDL +3489.053
1CL + 1PLB + -5.712
1.1TLB - 1.1BTB
0.841 -1.930 -54.104 -57.21
Min My 30340 1005 1DL 29384
+ 1SIDL +3383.634
1CL + 1PLA + 66.529
1PLB + 1.1TLA
16.877
+ 1.1TLB +-0.301
1.1BTA + 1.1BTB
-139.19 194.517
Max Mz 30340 1005 1DL 29384
+ 1SIDL +3383.634
1CL + 1PLA + 66.529
1PLB + 1.1TLA
16.877
+ 1.1TLB +-0.301
1.1BTA + 1.1BTB
-139.19 194.517
Min Mz 30340 1006 1DL 29384
+ 1SIDL +3984.184
1CL + 1PLA +-35.307
1PLB + 1.1TLA-1.35
+ 1.1TLB --2.413
1.1BTA - 1.1BTB
-69.863 -182.972
Pile 4
Beam L/C Node Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 30341 1005 1DL 29385
+ 1SIDL +4432.949
1CL + 1PLA + 92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB +-0.309
1.1BTA +-152.627
1.1BTB 410.439
Min Fx 30341 1002 1DL 29385
+ 1SIDL +3291.409
1CL + 1PLA + 17.443
1.1TLA - 1.1BTA
-0.261 -1.528 -75.179 125.667
Max Fy 30341 1005 1DL 29385
+ 1SIDL +4432.949
1CL + 1PLA + 92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB +-0.309
1.1BTA +-152.627
1.1BTB 410.439
Min Fy 30341 1006 1DL 29385
+ 1SIDL +3589.914
1CL + 1PLA + 1PLB
-9.476+ 1.1TLA
-2.024
+ 1.1TLB --2.382
1.1BTA - 1.1BTB
-64.349 29.403
Max Fz 30341 1005 1DL 29385
+ 1SIDL +4432.949
1CL + 1PLA + 92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB +-0.309
1.1BTA +-152.627
1.1BTB 410.439
Min Fz 30341 1006 1DL 29385
+ 1SIDL +3589.914
1CL + 1PLA + 1PLB
-9.476+ 1.1TLA
-2.024
+ 1.1TLB --2.382
1.1BTA - 1.1BTB
-64.349 29.403
Max Mx 30341 1001 1DL 29385
+ 1SIDL +3734.845
1CL + 1PLA + 68.718
1.1TLA + 1.1BTA
13.337 -0.072 -132.028 316.886
Min Mx 30341 1006 1DL 29385
+ 1SIDL +3589.914
1CL + 1PLA + 1PLB
-9.476+ 1.1TLA
-2.024
+ 1.1TLB --2.382
1.1BTA - 1.1BTB
-64.349 29.403
Max My 30341 1004 1DL 29389
+ 1SIDL +3447.227
1CL + 1PLB + 17.373
1.1TLB - 1.1BTB0.7 -1.908 -53.081 109.5
Min My 30341 1005 1DL 29385
+ 1SIDL +4432.949
1CL + 1PLA + 92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB +-0.309
1.1BTA +-152.627
1.1BTB 410.439
Max Mz 30341 1005 1DL 29385
+ 1SIDL +4432.949
1CL + 1PLA + 92.795
1PLB + 1.1TLA
18.525
+ 1.1TLB +-0.309
1.1BTA +-152.627
1.1BTB 410.439
Min Mz 30341 1006 1DL 29385
+ 1SIDL +3589.914
1CL + 1PLA + 1PLB
-9.476+ 1.1TLA
-2.024
+ 1.1TLB --2.382
1.1BTA - 1.1BTB
-64.349 29.403

2.2 Pile Loads

MDE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 9651 10294 9482 9778


Min Fx -2252 -2334 -2608 -2268
Max Fy 8711 10294 8853 9773
Min Fy -1536 -2334 -2133 -2268
Max Fz 9113 9789 9210 9605
Min Fz -1888 -1939 -2366 -2137
Max Mx 8711 10294 8853 9773
Min Mx -1536 -2334 -2133 -2268
Max My 9307 9980 9018 9411
Min My -1970 -2014 -2291 -2055
Max Mz 8711 10294 8853 9773
Min Mz -1536 -2334 -2133 -2268
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

ODE Seismic
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 7870 8283 7724 7974


Min Fx -1564 -1486 -1863 -1562
Max Fy 7027 7887 7019 7498
Min Fy -534 -855 -966 -906
Max Fz 7486 8029 7530 7850
Min Fz -1304 -1314 -1690 -1477
Max Mx 6882 7633 7005 7374
Min Mx -700 -918 -1165 -1001
Max My 7624 8166 7393 7712
Min My -1362 -1367 -1637 -1419
Max Mz 7027 7887 7019 7498
Min Mz -534 -855 -966 -906

Static
Load P1 P2 P3 P4 - - -
case kN kN kN kN - - -

Max Fx 4360 4612 3984 4433


Min Fx 3255 3589 3049 3291
Max Fy 3563 4612 3384 4433
Min Fy 4360 3966 3984 3590
Max Fz 3563 4612 3384 4433
Min Fz 4360 3966 3984 3590
Max Mx 3366 4051 3049 3735
Min Mx 4360 3966 3984 3590
Max My 4360 3966 3489 3447
Min My 3366 4051 3384 4433
Max Mz 3563 4612 3384 4433
Min Mz 4360 3966 3984 3590

3.1 Moment at Bottom Face:

Lever arm Z = Pile Centre to column face

Z = 0.80 m

Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or


2.0 m (P1+P2)xZ or (P3+P4)xZ, whichever
column is maximum

P kN
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = 510.276 kN.m
Design Moment, M = M1 - M2

Case M1 (kN.m) M = (M1 - M2) (kN.m)


MDE Seismic 16057.600 15470.782
ODE Seismic 13005.600 12495.324
Static 7236.000 6725.724

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
2
K = Mu/bd fcu = 0.020 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.95 d = 1626.88 mm
As = Mu / (fy z)
Ast = 24383.356 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 100 0 0 0 0

= 25530.349 mm2 OK

3.2 Moment at Top Face:

Lever arm Z = Pile Centre to column face

P kN Z = 0.80 m
2.0 m
column Z = 0.8m M1 = (P1+P3)xZ or (P2+P4)xZ or
(P1+P2)xZ or (P3+P4)xZ, whichever
is minimum

Weight per unit length due to soil and pile cap = 374.858 kN/m
Moment due to unit weight, M2 = -510.276 kN.m
Design Moment, M = M1 + M2

Case M1 (kN.m) M = (M1 + M2) (kN.m)


MDE Seismic -3900.800 -4487.618
ODE Seismic -2741.600 -3251.876
Static 0.000 0.000

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

K = Mu/bd2fcu = 0.006 K'


Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1713.23 mm
Hence, z = 0.95 d = 1627.57 mm
As = M u / (f y z)
Ast = 7069.893 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


23.547 100 0 0 0 0
(Y25 + Y22 ALT.)
= 22655.269 mm2 OK

3.3 Moment Capacity, Stress and Crack Width Check from Oasys

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 15470 20210 0.7656 OK
Minima
2 0.0 4488 17960 0.2499 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
25.93 OK
25.93 OK
Minima
-141.4 OK
-141.4 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fcu 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

Oasys Results
Cocncrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
3 2.116 OK 3 11.97 OK
3 2.116 OK 3 11.97 OK
Minima Minima
3 -0.5803 OK 3 -39.32 OK
3 -0.5803 OK 3 -39.32 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.135 mm OK

3.4 Minimum Reinforcement


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4008.95 mm2/m
At bottom face, Provided = 4817 mm2/m
Astprovided > Astmin OK
At top face, Provided = 4275 mm2/m
Astprovided > Astmin OK

4.0 Shear Check


Total pile reaction, V1 = 20072 kN
As per Cl. 3.11.4.3, pg. 82, BS 8110-1: 1997, critical section for shear should be located 20% of the pile diameter inside
Distance of critical section for shear check from column face = 0.440 m
Factored weight per unit length due to soil and pile cap = 431.087 kN/m
Hence, downward reaction due to soil and pile cap weight,
V2 = weight per unit length x (length of pile cap - 0.5 x column size - distance of critical section)
V2 = 522 kN
Net reaction, Vu = V1 - V2 = 19550 kN
Width of pile cap available b = 5.300 m
Effective depth of pile cap d = 1.713 m
Area of tensile steel provided As = 25530 mm2
= 0.026 m2
Percentage of tensile steel provided 100As/(b.d) = 0.281 %
Shear stress = Vu /(b.d) = 2154.02 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.34 MPa
= 340 kN/sqm
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Nishant
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

As per Cl. 3.11.4.4, pg. 82, BS 8110-1:1997,


Enhanced shear strength of concrete, say vc,1 = 2.d.vc /av
av = 0.440 m
Therefore, vc,1 = 2.65 MPa
= 2647 kN/sqm
Vus = Vu - vc,1 b d = -4470.74 kN

Requirement of shear reinforcement = Not Required

5.0 Check for punching shear


Total pile load = 39205 kN
From section 1.0 above, factored weight of pile cap + earthfill = 1987 kN
Hence, net punching shear force = 37218 kN
Effective depth of pile cap = 1.713 m
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, punching shear shall be checked at the perimeter of the column.
Shear perimeter = 8.000 m
Shearing Area = 13.700 m2
Punching Shear stress = 2716.661 kN/m2
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997,
Allowable punching shear stress = lesser of 0.8 fcu or 5 N/mm2 = 5.00 N/mm2
= 5000.000 kN/m2
OK
As per Cl. 3.11.4.5, pg. 83, BS 8110-1: 1997, since the pile spacing is not greater than 3 times the pile diameter, no
additional punching shear check is required.
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR GROUP PG2


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Pile Group = PG2

No. of piles n = 2
Dia of pile = 1.20 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 4.245 m x 4.250 m


Area of pile cap = 18.04 m2
Depth of pile cap D = 1.80 m
Volume of pile cap = 32.47 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 811.86 kN

Thickness of Earthfill over pile cap = 0.00 m

Total weight of (Pile cap + Earthfill) = 811.86 kN

2.1 Moment in Longitudinal Direction:

Case Moment from STAAD (kN.m)


MDE Seismic 11123.508
ODE Seismic 8866.571
Static 1504.398

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
K = Mu/bd2fcu = 0.018 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.950 d = 1626.875 mm
As = Mu / (fy z)
Ast = 17532 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 100 0 0 0 0

= 20376 mm2 OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

2.2 Moment Capacity, Stress and Crack width check from Oasys for Longitudinal Direction

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 11120 1279 0.869 OK
Minima
1 0.0 11120 1279 0.869 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
37.39 OK
37.39 OK
Minima
-212.3 OK
-212.3 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fck 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa

Oasys Results
Concrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
2 0.6122 OK 2 3.684 OK
2 0.6122 OK 2 3.684 OK
Minima Minima
2 -0.6122 OK 2 -3.684 OK
2 -0.6122 OK 2 -3.684 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.007 mm OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

2.3 Moment in Transverse Direction:

Case Moment from STAAD (kN.m)


MDE Seismic 18266.176
ODE Seismic 14591.063
Static 2422.889

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
K = Mu/bd2fcu = 0.029 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1709.00 mm
Hence, z = 0.950 d = 1623.55 mm
As = Mu / (fy z)
Ast = 28848 mm2
Astprovided = Dia Spacing Dia Spacing Dia Spacing
32 100 0 0 0 0

= 33288 mm2 OK

2.4 Moment Capacity, Stress and Crack width check from Oasys for Transverse Direction

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 18270 2069 0.883 OK
Minima
1 0.0 18270 2069 0.883 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
51.96 OK
51.96 OK
Minima
-244.1 OK
-244.1 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fck 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa

Oasys Results
Section Material stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
2 0.9476 OK 2 5.678 OK
2 0.9476 OK 2 5.678 OK
Minima Minima
2 -0.9476 OK 2 -5.678 OK
2 -0.9476 OK 2 -5.678 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.011 mm OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

2.5 Minimum reinforcement on tension face


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4007.25 mm2/m
In longitudinal direction, Provided = 4794 mm2/m
Astprovided > Astmin OK
In transverse direction, Provided = 7842 mm2/m
Astprovided > Astmin OK

3.0 Top Reinforcement


Top Reinforcement should be 0.234% of cross-sectional area.
Required Steel = 4007.25 mm2/m
In longitudinal direction,
Dia 25 Spacing 100 Provided = 4794 mm2/m
OK
In transverse direction,
Dia 32 Spacing 100 = 7842 mm2/m
Provided
OK

4.1 Shear Check in Longitudinal Direction


Shear force from STAAD Vu = 6613 kN
Width of pile cap available b = 1.700 m
Effective depth of pile cap d = 1.713 m
Area of tensile steel provided As = 8150 mm2
0.008 m2
Percentage of tensile steel provided 100As/(b.d) = 0.280 %
Shear stress = Vu /(b . d) = 2271.42 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.34 MPa
340 kN/sqm
Vus = Vu - vc b d = 5622.84 kN
Requirement of shear reinforcement = Required
From Table 3.16, pg. 46, BS 8110-1: 1997,
For minimum links, Vus,min = 0.4 b d = 1164.50 kN
Dia of stirrup 19 mm
No. of legs 17
As per Table 3.16, pg. 46, BS 8110-1: 1997, spacing required,
sv = 0.87 fyv Asv d / Vus 498 mm
Provided spacing 422.5 mm
OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

4.2 Shear Check in Transverse Direction


Shear force from STAAD Vu = 8614 kN
Width of pile cap available b = 1.700 m
Effective depth of pile cap d = 1.709 m
Area of tensile steel provided As = 13331 mm2
0.013 m2
Percentage of tensile steel provided 100As/(b.d) = 0.459
Shear stress = Vu /(b . d) = 2964.89 kN/sqm
Grade of concrete = 50
Shear strength of concrete, vc = 0.4 MPa
400 kN/sqm
Vus = Vu - vc b d = 7451.78 kN
Requirement of shear reinforcement = Required
From Table 3.16, pg. 46, BS 8110-1: 1997,
For minimum links, Vus,min = 0.4 b d = 1162.12 kN
Dia of stirrup 19 mm
No. of legs 5
As per Table 3.16, pg. 46, BS 8110-1: 1997, spacing required,
sv = 0.87 fyv Asv d / Vus 110 mm
Provided spacing 100 mm
OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

PILE CAP FOR GROUP PG2A


Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

1.0 INPUT DATA

Pile Group = PG2A

No. of piles n = 2
Dia of pile = 1.20 m
Centre to centre distance of pile = 3.60 m
Grade of concrete = C50
Grade of steel = Fe390
Clear cover to the reinforcement = 75 mm

Size of pile cap = 4.245 m x 4.250 m


Area of pile cap = 18.04 m2
Depth of pile cap D = 1.80 m
Volume of pile cap = 32.47 m3
Density of RCC = 25.00 kN/cum
Weight of pile cap = 811.86 kN

Thickness of Earthfill over pile cap = 0.00 m

Total weight of (Pile cap + Earthfill) = 811.86 kN

2.1 Moment in Longitudinal Direction:

Case Moment from STAAD (kN.m)


MDE Seismic 7733.296
ODE Seismic 6244.538
Static 2584.085

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
K = Mu/bd2fcu = 0.012 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.950 d = 1626.875 mm
As = Mu / (fy z)
Ast = 12188 mm2

Astprovided = Dia Spacing Dia Spacing Dia Spacing


25 120 0 0 0 0

= 17062 mm2 OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

2.2 Moment Capacity, Stress and Crack width check from Oasys for Longitudinal Direction

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 7733. 10930 0.7078 OK
Minima
1 0.0 7733. 10930 0.7078 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
27.4 OK
27.4 OK
Minima
-152.2 OK
-152.2 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fck 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa

Oasys Results
Concrete stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
2 1.062 OK 2 6.391 OK
2 1.062 OK 2 6.391 OK
Minima Minima
2 -1.062 OK 2 -6.391 OK
2 -1.062 OK 2 -6.391 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.012 mm OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

2.3 Moment in Transverse Direction:

Case Moment from STAAD (kN.m)


MDE Seismic 7334.634
ODE Seismic 5695.402
Static 1146.799

As per Cl. 3.4.4.4, pg. 28, BS 8110-1:1997,


K' = 0.156
K = Mu/bd2fcu = 0.012 K'
Hence, compression reinforcement is not required.
z = d [ 0.5 + ( 0.25 - K/0.9 )], but not greater than 0.95d.
Here, effective depth of pile cap, d = 1712.50 mm
Hence, z = 0.950 d = 1626.875 mm
As = Mu / (fy z)
Ast = 11560 mm2
Astprovided = Dia Spacing Dia Spacing Dia Spacing
25 120 0 0 0 0

= 17042 mm2 OK

2.4 Moment Capacity, Stress and Crack width check from Oasys for Transverse Direction

a) Moment Capacity Check for MDE Seismic:


Oasys Results
Case N M Mu M/Mu
[kN] [kNm] [kNm]
Maxima
1 0.0 7335. 10920 0.6716 OK
Minima
1 0.0 7335. 10920 0.6716 OK

b) Reinforcement Stress Check for ODE Seismic:


Permissible stress = Yield stress / 1.15 = 390 / 1.15 = 339.13 N/mm2
Oasys Results
Case Stress
[N/mm²]
Maxima
24.87 OK
24.87 OK
Minima
-132.4 OK
-132.4 OK

c) Stress Check for Static Case:


Permissible stresses from Table 2, pg. 8, BS 5400-4: 1990
Concrete 0.5fck 25.000 MPa (due to bending)
Steel 0.75fy 292.500 MPa

Oasys Results
Section Material stresses at SLS Loads Reinforcement stresses at SLS Loads
Case Stress Case Stress
[N/mm²] [N/mm²]
Maxima Maxima
2 0.4705 OK 2 2.831 OK
2 0.4705 OK 2 2.831 OK
Minima Minima
2 -0.4734 OK 2 -2.85 OK
2 -0.4734 OK 2 -2.85 OK

d) Crack Width Check:


From Table 1, pg. 7, BS 5400-4: 1990, for buried parts of structures subjected to severe environment,
Permissible crack width = 0.250 mm
Oasys Results
Design surface crack width = 0.005 mm OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

2.5 Minimum reinforcement on tension face


As per Cl. 9.2.1.1, pg. 152, EN 1992-1-1: 2004 (E),
Minimum area of longitudinal tension reinforcement, As,min = 0.26 (fctm/fyk) btd
From Table 3.1, pg. 29, EN 1992-1-1: 2004 (E), for C50 concrete, fctm = 3.5 N/mm2
Hence, As,min = 0.26*(3.5/390)*b*d = 0.234/100*b*d = 4007.25 mm2/m
In longitudinal direction, Provided = 4015 mm2/m
Astprovided > Astmin OK
In transverse direction, Provided = 4014 mm2/m
Astprovided > Astmin OK

3.0 Top Reinforcement


Top Reinforcement should be 0.234% of cross-sectional area.
Required Steel = 4007.25 mm2/m
In longitudinal direction,
Dia 25 Spacing 120 Provided = 4015 mm2/m
OK
In transverse direction,
Dia 25 Spacing 120 = 4014 mm2/m
Provided
OK

4.1 Shear Check in Longitudinal Direction


Shear force from STAAD Vu = 4327 kN
Width of pile cap available b = 1.700 m
Effective depth of pile cap d = 1.713 m
Area of tensile steel provided As = 6825 mm2
0.007 m2
Percentage of tensile steel provided 100As/(b.d) = 0.234 %
Shear stress = Vu /(b . d) = 1486.25 kN/sqm
Grade of concrete = C50
Design shear resistance is calculated as per Cl. 3.11.4.4, pg. 82, BS 8110-1: 1997.
Shear strength of concrete, vc = 0.32 MPa
320 kN/sqm
Vus = Vu - vc b d = 3395.24 kN
Requirement of shear reinforcement = Required
From Table 3.16, pg. 46, BS 8110-1: 1997,
For minimum links, Vus,min = 0.4 b d = 1164.50 kN
Dia of stirrup 13 mm
No. of legs 15
As per Table 3.16, pg. 46, BS 8110-1: 1997, spacing required,
sv = 0.87 fyv Asv d / Vus 341 mm
Provided spacing 281.67 mm
OK
Project JMRT Sheet
Client TWJO
Job Design of Stations
Station Lebak Bulus Prepared Jai
Doc No - Checked Reyaz
Title Design of Pile Caps Verified Sumant

4.2 Shear Check in Transverse Direction


Shear force from STAAD Vu = 4318 kN
Width of pile cap available b = 1.700 m
Effective depth of pile cap d = 1.713 m
Area of tensile steel provided As = 6825 mm2
0.007 m2
Percentage of tensile steel provided 100As/(b.d) = 0.234
Shear stress = Vu /(b . d) = 1483.09 kN/sqm
Grade of concrete = 50
Shear strength of concrete, vc = 0.32 MPa
320 kN/sqm
Vus = Vu - vc b d = 3386.06 kN
Requirement of shear reinforcement = Required
From Table 3.16, pg. 46, BS 8110-1: 1997,
For minimum links, Vus,min = 0.4 b d = 1164.50 kN
Dia of stirrup 13 mm
No. of legs 5
As per Table 3.16, pg. 46, BS 8110-1: 1997, spacing required,
sv = 0.87 fyv Asv d / Vus 114 mm
Provided spacing 110 mm
OK
NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


FOUNDATION GENERAL
PRESIDENT DIRECTOR NOTES FOR STATION
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
DESIGNED BY AS SHOWN 1/CWD/GNL/0010 - T
PROJECT MANAGER
PT. AECOM INDONESIA 1-CWD-GNL-0010
PILE GROUP LAYOUT

NOTES:-

STRUCTURE REFERENCE DRAWINGS:


IN CONJUNCTION WITH THIS DRAWING NO.

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE LAYOUT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3016 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3016-3017-1 (PILE LAYOUT).DWG
4 4

PILE GROUP LAYOUT

IN CONJUNCTION WITH THIS DRAWING NO. 6 6

STRUCTURE REFERENCE DRAWING: NOTES:-

NORTH

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE LAYOUT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3017 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3016-3017-1 (PILE LAYOUT).DWG
REINFORCEMENT DETAILS OF PILE
A COLUMN / PILE GROUP BAR MARKED
MARKED

** DEPTH OF PILE CAP

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3021 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3021-1 (PILE REINFORCEMENT).DWG
REINFORCEMENT DETAILS OF PILE
COLUMN / PILE GROUP BAR MARKED
MARKED

** DEPTH OF PILE CAP

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3022 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3022-1 (PILE REINFORCEMENT).DWG
1 1 LONGITUDINAL
AXIS
A A

LEGEND :

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE CAP REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
1:200 1/STN/STR/3026 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3026-1.DWG
LONGITUDINAL
AXIS
1 1

A A

LEGEND :

NOTES:-

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE CAP REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
1:200 1/STN/STR/3027 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3027-1.DWG
1 1 LONGITUDINAL
AXIS
A A

NOTES:-

LEGEND :

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE CAP REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
1:200 1/STN/STR/3028 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3028-1.DWG
1 1

LEGEND :

NOTES:-

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE CAP REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
1:200 1/STN/STR/3029 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3029-1.DWG
1 1

LEGEND :

NOTES:-

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
PILE CAP REINFORCEMENT
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
1:200 1/STN/STR/3030 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3030-1.DWG
SCHEDULE OF COLUMNS

NOTES

IN CONJUNCTION WITH THIS DRAWING NO.

STRUCTURE REFERENCE DRAWING:

NORTH

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
COLUMN LAYOUT PLAN
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3001 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-SRT-3001 & 3002-1 (COLUMN LAYOUT)
SCHEDULE OF COLUMNS

NOTES

IN CONJUNCTION WITH THIS DRAWING NO.

STRUCTURE REFERENCE DRAWING:

NORTH

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
COLUMN LAYOUT PLAN
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3002 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-SRT-3001 & 3002-1 (COLUMN LAYOUT).DWG
1 2 3 4 5 6 7 8 9

FUTURE
ESCALATOR 1

IN CONJUNCTION WITH THIS DRAWING NO.


FRAMING PLAN AT CONCOURSE AT +45.90M ( T.O.C. ) LEVEL
SCHEDULE OF COLUMNS

SCHEDULE OF BEAM
STRUCTURE REFERENCE DRAWING:

NOTES:-

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
FRAMING PLAN AT CONCOURSE LEVEL
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3003 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3003 & 3004-1 (CONCOURSE LEVEL).DWG
C
10 11 12 13 14 15 16 17

FRAMING PLAN AT CONCOURSE AT +45.90M ( T.O.C. ) LEVEL

SCHEDULE OF COLUMNS
IN CONJUNCTION WITH THIS DRAWING NO. SCHEDULE OF BEAM

STRUCTURE REFERENCE DRAWING:

NOTES:-

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
FRAMING PLAN AT CONCOURSE LEVEL
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3004 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3003 & 3004-1 (CONCOURSE LEVEL).DWG
SCHEDULE OF COLUMNS

BEAM SCHEDULE

STRUCTURE REFERENCE DRAWING:

SCHEDULE OF COLUMNS

NORTH

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
FRAMING PLAN AT TRACK LEVEL
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3005 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3005-1 (TRACK LEVEL)
SCHEDULE OF COLUMNS

SCHEDULE OF BEAM

STRUCTURE REFERENCE DRAWING:

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
FRAMING PLAN AT PLATFORM LEVEL
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3006 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3006-1 (PLATFORM LEVEL).DWG
NOTES:-

ARCHITECTURAL REFERENCE DRAWING:

NOTES:- STRUCTURE REFERENCE DRAWING:

IN CONJUNCTION WITH THIS DRAWING NO.

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
LONGITUDINAL SECTION
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3007 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3007 TO 3009-1 (SECTION-4).DWG
NOTES:-

ARCHITECTURAL REFERENCE DRAWING:


NOTE:-

IN CONJUNCTION WITH THIS DRAWING NO.

STRUCTURE REFERENCE DRAWING:

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
LONGITUDINAL SECTION
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3008 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3007 TO 3009-1 (SECTION-4).DWG
NOTES:-

ARCHITECTURAL REFERENCE DRAWING:

NOTE:-

IN CONJUNCTION WITH THIS DRAWING NO.

STRUCTURE REFERENCE DRAWING:

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
LONGITUDINAL SECTION
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3009 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3007 TO 3009-1 (SECTION-4).DWG
B ARCHITECTURAL REFERENCE DRAWING:

LEGENDS:-

NOTE:-

STRUCTURE REFERENCE DRAWING:

NOTES:

ENDORSED BY Construction of Jakarta Mass Rapid Transit Project


Contract CP 101

APPROVED BY NOTICED BY NAME SIGNATURE


01 LEBAK BULUS STATION
TRANSVERSE SECTION
PRESIDENT DIRECTOR
VERIFIED BY

DIRECTOR OF
CONSTRUCTION
AS SHOWN 1/STN/STR/3010 1 T
DESIGNED BY
PROJECT MANAGER
PT. AECOM INDONESIA 1-STN-STR-3010-1 (SECTION-1, 2 & 3)

You might also like