Professional Documents
Culture Documents
: ________
INSTRUCTION: Select the correct answer for each of the following questions.
Mark only one answer for each item by shading the box corresponding to the
letter of your choice on the answer sheet provided. STRICTLY NO ERASURES
ALLOWED.
MULTIPLE CHOICE
Page 1 of 33
https://marcusaustria.com/plumbing
b. Waste branch
c. Soil/wase branch
d. Soil branch
7. That portion of the vent pipe system, serving as terminal for the
smaller forms of individual and grouped fixture trap ventilation,
sometimes referred as collecting vent line.
a. Stack vent
b. Main vent
c. Circuit vent
d. Yoke vent
Page 2 of 33
https://marcusaustria.com/plumbing
Page 3 of 33
https://marcusaustria.com/plumbing
c. Loop vent
d. Individual vent
22. A hammer which is used most often in a home for general carpentry and
household chores. It should be used only with non-hardened, common
or finishing nails.
Page 4 of 33
https://marcusaustria.com/plumbing
24. A hammer which is used with small shank, cold chisels for cutting and
chipping work, rounding over rivet ends, forming unhardened metal
work and similar jobs not involving nails.
a. hand drilling hammer
b. ball peen hammer
c. ripping claw hammer
d. tacking hammer
25. A hammer weighing between 2 lbs. and 4 lbs., easy to handle with a
powerful punch. With short handle and is recommended for pounding
hardened nails into concrete or for using with tools that drive nails
and pins into concrete or brick.
a. hand drilling hammer
b. ball peen hammer
c. ripping claw hammer
d. tacking hammer
26. A hammer which is used for extremely heavy jobs where great force is
required.
a. hand drilling hammer
b. ball peen hammer
c. mallet
d. sledge hammer
Page 5 of 33
https://marcusaustria.com/plumbing
Page 6 of 33
https://marcusaustria.com/plumbing
33. A plier of two designs: multiple hole and tongue and groove. The
adjustable joint enables the tool to adjust to the size of the object
being held.
a. Thin-nose plier
b. Duck bill plier
c. Wire stripper
d. Slip-joint plier
34. Also called bent-nose pliers, since the nose is bent at about an 80-
degree angle for reaching around objects.
a. Thin-nose plier
b. Duck bill plier
c. Wire stripper
d. Slip-joint plier
35. A plier with long, tapered, flat nose for work in restricted areas.
a. Thin-nose plier
b. Duck bill plier
c. Wire stripper
d. Slip-joint plier
37. It has heavy toothed jaws for gripping pipe. It is used to hold or
turn threaded pipe during assembly.
a. Straight pipe wrench
b. End pipe wrench
c. Offset pipe wrench
d. All of the above
Page 7 of 33
https://marcusaustria.com/plumbing
Page 8 of 33
https://marcusaustria.com/plumbing
Page 9 of 33
https://marcusaustria.com/plumbing
Page 10 of 33
https://marcusaustria.com/plumbing
Page 11 of 33
https://marcusaustria.com/plumbing
62. The condition of the wrench's teeth is directly related to the tool's
ability to grip pipe. You should periodically clean the teeth and
sharpen them with a ______.
a. triangular file
b. pipe reamer
c. soapstone
d. gripping tool
63. A wrench which is often used to hold or rotate pipe with a diameter
of more than 2". It requires less space around the pipe than pipe
wrenches. In addition, less likely to crush the pipe because it
applies pressure more uniformly.
a. End pipe wrench
b. Chain wrench
c. Compound leverage wrench
d. Raprench wrench
65. Also called a spud wrench, looks like a pipe wrench, but it is
different in two significant ways: the jaws are smooth and there is
no provision for the jaws to tighten on the part being turned as
pressure is applied to the wrench.
a. Straight pipe wrench
b. Raprench wrench
Page 12 of 33
https://marcusaustria.com/plumbing
c. Stillson wrench
d. Monkey wrench
68. The system of plumbing pipes used in the removal of liquid and solid
waste from a building.
a. Plumbing System
b. DWV System
c. Private Sewage Disposal System
d. Sewer System
Page 13 of 33
https://marcusaustria.com/plumbing
74. A tool for enlarging holes and for removing metal burrs from the
inside of pipes.
a. Threader
b. Ruler
c. Reamer
d. Deburrer
75. A handheld reciprocating saw that can be used to cut cast iron pipe.
a. Sawzall
Page 14 of 33
https://marcusaustria.com/plumbing
b. Jigsaw
c. Hacksaw
d. Key hole saw
76. It is a plumbing snake inside a protective tube that has a bent end,
used to unclog a toilet when a toilet plunger is not successful.
a. Toilet auger
b. Plunger
c. Flue brush
d. Cable tie
78. Water supply lines in a home can be made by any of the following
EXCEPT
a. Cast iron
b. Copper
c. Plastic
d. Galvanized steel
Page 15 of 33
https://marcusaustria.com/plumbing
a. Melting
b. Smelting
c. Sweating
d. Perspiration
81. Identify FIG. WC-a. This bowl is the least expensive and the simplest
type of water closet. The trap is at the front of the bowl, and small
streams of water running down from the rim flush the bowl.
a. Common Washdown Bowl
b. Washdown Bowl With Jet
c. Reverse-Trap Bowl
d. Siphon-Jet Bowl
82. Identify FIG. WC-b. This bowl is similar to the washdown bowl but is
flushed differently. The unit has a small hole in the bottom, which
delivers a direct jet as the unit is flushed. The jet, directed into
the upper arm of the trap, starts a siphoning action.
a. Common Washdown Bowl
b. Washdown Bowl With Jet
c. Reverse-Trap Bowl
d. Siphon-Jet Bowl
83. Identify FIG. WC-c. This bowl is similar to the washdown bowl, except
that the trap is at the rear of the bowl, making the bowl longer.
This bowl holds more water than the washdown bowl and is quieter in
operation.
a. Common Washdown Bowl
b. Washdown Bowl With Jet
c. Reverse-Trap Bowl
d. Siphon-Jet Bowl
84. Identify FIG. WC-d. This bowl is the most efficient, the quietest,
and the most expensive water closet. It looks like the reverse-trap
bowl but holds more water. It is almost completely filled with water.
a. Common Washdown Bowl
b. Washdown Bowl With Jet
Page 16 of 33
https://marcusaustria.com/plumbing
c. Reverse-Trap Bowl
d. Siphon-Jet Bowl
85. It is a pipe or opening that brings outside air into the plumbing
system and equalizes the pressure on both sides of a trap to prevent
trap seal loss.
a. Standpipe
b. Vent
c. Trap
d. Tube
86. It provides a water seal that keeps sewer gases from entering a
building
through a waste outlet.
a. Standpipe
b. Vent
c. Trap
d. Tube
87. It is used in a building's drain line when the local plumbing code
requires that the building drain be trapped.
a. Running trap
b. S-trap
c. P-trap
d. ¾ S-trap
Page 17 of 33
https://marcusaustria.com/plumbing
92. What is that valve recommended for installations that call for
throttling?
a. Globe valve
b. Check valve
c. Gate valve
d. Backwater valve
93. What is the approximate height above the floor level of a kitchen
sink?
a. 30 inches
b. 34 inches
c. 36 inches
d. 38 inches
Page 18 of 33
https://marcusaustria.com/plumbing
97. What is the approximate height above floor level of a built-in bathtub
floor level?
a. 12 inches
b. 18 inches
c. 16 inches
d. 24 inches
Page 19 of 33
https://marcusaustria.com/plumbing
Page 20 of 33
https://marcusaustria.com/plumbing
Page 21 of 33
https://marcusaustria.com/plumbing
Page 22 of 33
https://marcusaustria.com/plumbing
Page 23 of 33
https://marcusaustria.com/plumbing
Page 24 of 33
https://marcusaustria.com/plumbing
Page 25 of 33
https://marcusaustria.com/plumbing
Page 26 of 33
https://marcusaustria.com/plumbing
Page 27 of 33
https://marcusaustria.com/plumbing
Page 28 of 33
https://marcusaustria.com/plumbing
Page 29 of 33
https://marcusaustria.com/plumbing
Page 30 of 33
https://marcusaustria.com/plumbing
Page 31 of 33
https://marcusaustria.com/plumbing
Page 32 of 33
https://marcusaustria.com/plumbing
PRACTICAL PROBLEMS
ANSWER SHEET
https://marcusaustria.com/plumbing
Page 33 of 33