Professional Documents
Culture Documents
Chapter 2
Chapter 2
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 1/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 1
Sai
Based on the technical requirements, the limiting deviations of the shaft diameter Ø60 can be defined from the dimension:
Select one:
a. Ø60H13.
c. Ø60js13.
d. Ø60h13.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 2/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
A fit in the basic hole system has TD = Td, Nmax = 25μm and bilateral tolerance of shaft. Determine limiting deviations of the hole and shaft.
Select one:
a. ES = 25µm, EI = 0, es = 12,5µm, ei = -12,5µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 3/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Sai
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the B joint .
Select one:
a. Clearance fit in the basic shaft system.
The correct answer is: Transition fit in the basic hole system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 4/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Match diameters of hole and shaft in the two following columns in order to create the fit Ø45H7/n6.
Select one:
a. 7 – e.
b. 2 – b. Your answer is
incorrect.
c. 2 – j.
d. 2 – h.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 5/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Sai
Fit for a joint between a idler gear and a shaft can be choosen as follows:
Select one:
a.
b. Your answer is
incorrect.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 6/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Không trả lời
Choose the proper fit between the bearing cover 6 and housing 1 of a reduction gearbox.
Select one:
a. Ø80U8/h7.
b. Ø80F7/h6.
c. Ø80H7/e8.
d. Ø80H8/k7.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 7/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
From the assembly drawing, determine dimensions of the components in the machine cluster as follows:
Select one:
a. Φ55-0,030 : hole diameter of the part 3 ; Φ55-0,030 : hole diameter of the part 1 ; Φ55±0,0095 : diameter of the shaft 2.
b. Φ55 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55-0,019 : diameter of the shaft 2.
c. Φ55 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55 : diameter of the shaft 2.
d. Φ55-0,030 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55-0,019 : diameter of the shaft 2.
The correct answer is: Φ55-0,030 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55-0,019 : diameter of the shaft 2.
Câu hỏi 8
Không trả lời
Collect all interference fits in the basic hole system from the following:
Select one:
a. H7/t6 ; H7/r6 ; H8/s7.
b. H7/t6 ; H7/r6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 8/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Không trả lời
From the fit on the assembly drawing, determine proper the gear hole D and shaft diameter d .
Select one:
a. D = Ø40-0,025 and d = Ø40 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 9/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
Choose suitable fit for the gears 2, 3 and 4 on the counter shaft of the speed gear box
Select one:
a. H7/p6 or H7/r6.
b. H7/k6 or H7/m6.
c. K7/h6 or H7/m6.
d. H7/k6 or H8/e8.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 10/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
Select one:
a. Interference fit in the basic shaft system with the average interference Ntb = 29,5μm.
b. Clearance fit in the basic hole system with the average clearance Stb = 20,5μm.
c. Interference fit in the basic shaft system with the average interference Ntb = 20,5μm.
d. Clearance fit in the basic hole system with the average clearance Stb = 29,5μm.
The correct answer is: Clearance fit in the basic hole system with the average clearance Stb = 29,5μm.
Câu hỏi 12
Không trả lời
With the given fits ø80H6/k5 and ø80M7/h6, select the correct sentence.
Select one:
a. The limits of size for the hole in the first fit are equal to the limits of size for the shaft in the second fit.
b. The maximum hole in the first fit is equal to the minimum shaft in the second fit.
c. The minimum hole in the first fit is equal to the maximum shaft in the second fit.
d. The limits of size for the shaft in the first fit are equal to the limits of size for the hole in the second fit.
The correct answer is: The minimum hole in the first fit is equal to the maximum shaft in the second fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 11/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
With a given transition fit Ø45H7/n6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. Ø45H7/k6 or Ø45H7/m6.
b. Ø45H7/js6 or Ø45M7/h6.
c. Ø45H7/js6 or Ø45K7/h6.
d. Ø45H7/k6 or Ø45H7/f6.
Câu hỏi 14
Không trả lời
Choose the type of fit for the impeller and the pulley that are mounted on the shaft of an industrial fan:
Select one:
a. Transition fit in the basic shaft system for the joint between the impeller and shaft; clearance fit in the basic hole system for the
joint between the pulley and shaft.
c. Clearance fit in the basic hole system for the joint between the impeller and shaft; transition fit in the basic shaft system for the
joint between the pulley and shaft.
The correct answer is: Transition fit in the basic hole system for two joints.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 12/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Collect all transition fits in the basic hole system from the following:
Select one:
a. H7/m6 ; H8/k7 ; H7/js6 ; H7/h6.
Câu hỏi 16
Không trả lời
With a given transition fit H7/k6, it is necessary to select another fit in order to increase the probability of interference
Select one:
a. H7/r6
b. H7/m6
c. H7/js6
d. M7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 13/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Based on the technical requirements, the limiting deviations of the unfitted dimensions Ø30 , Ø50 and 305 can be defined as follows:
Select one:
a. Ø30-0,39 ; Ø50-0,33 and 305±0,4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 14/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
If fundamental deviation of a shaft is e and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by es = Td + ei
Câu hỏi 19
Không trả lời
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/f7 and B = Ø42M7/h6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø41,75 ; D2max = Ø42 and d2min = Ø41,84 ; d2max = Ø42.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,979 ; d1max = Ø30.
Fit of dimension B: D2min = Ø41,975 ; D2max = Ø42 and d2min = Ø41,984 ; d2max = Ø42.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø41,975 ; D2max = Ø42 and d2min = Ø41,984 ; d2max = Ø42.
d. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø41,975 ; D2max = Ø42 and d2min = Ø41,984 ; d2max = Ø42.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø41,975 ; D2max = Ø42 and d2min = Ø41,984 ; d2max = Ø42.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 15/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
When designing shaft, determine shaft diameters from given fits on the assembly drawing of reduction gearbox.
Select one:
a. Ø25 ; Ø40 ; Ø36-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 16/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Because of axial movement of tailstock spindle in hole Φ35 of the tailstock body, fit between spindle and hole can be selected as follows
Select one:
a. Φ35G6/h5.
b. Φ35H6/h5.
c. Φ35H6/n5.
d. Φ35H7/f7.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 17/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Select a transition fit in which the probability of interference is a little bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø50+0,025 ; d = Ø50 .
b. D = Ø50-0,025 ; d = Ø50 .
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50+0,025 ; d = Ø50±0,008.
Câu hỏi 23
Không trả lời
Interference fits in the basic shaft system are created by fundamental deviations as follows:
Select one:
a. From p to zc.
b. From A to H.
c. From P to ZC.
d. From a to h.
Câu hỏi 24
Không trả lời
Select one:
a. Probability of interference is about 80%.
The correct answer is: Probability of interference is slightly larger than probability of clearance.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 18/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
With two given fits Ø50H6/g5 and Ø50G6/h5, select the wrong sentence.
Select one:
a. The minimum limit for the hole in the first fit is equal to the maximum limit of size for the shaft in the second fit.
d. The shaft upper deviation in the first fit is equal to the hole lower deviation in the second fit.
The correct answer is: The shaft upper deviation in the first fit is equal to the hole lower deviation in the second fit.
Câu hỏi 26
Không trả lời
Sort the following fits in ascending order of clearance probability and in descending order of interference probability (if they have the
same nominal size):
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 19/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
From the fit between the pulley 7 and the shaft 2 (D = d = Ø30) on the assembly drawing, determine the limiting deviations of the pulley
hole and shaft.
Select one:
a. ES = 21µm , EI = 0 ; and es = 15µm , ei = 2µm.
Câu hỏi 28
Không trả lời
From the following fits, select one in the basic shaft system, of which the interference is the biggest:
Select one:
a. H8/u8
b. S7/h6
c. U8/h7
d. E8/h7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 20/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/g6 and B = Ø42H7/m6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
b. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
d. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,09 ; d2max = Ø42,25.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 21/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create all clearance fits in the basic shaft system.
Select one:
a. 2 – e ; 3 – e ; 8 – a.
b. 3 – e ; 10 – g.
c. 4 – e ; 8 – e.
d. 2 – e ; 4 – e ; 8 – e.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098285&cmid=1147996 22/22
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Sai
Select one:
a. d4
b. d3
c. d1 Your answer is
incorrect.
d. d2
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 1/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
From the assembly drawing, determine limitimg deviations of the component dimensions 1, 2 and 3 (D = d = Ø18) in the machine cluster
as follows:
Select one:
a. EI1 = 0 , ES1 = 18µm ; ei2 = -11µm , es2 = 0 ; EI3 = -18µm , ES3 = 0.
b. EI1 = -18µm , ES1 = 0µm ; ei2 = -5,5µm , es2 = 5,5µm ; EI3 = -18µm , ES3 = 0.
c. EI1 = 0 , ES1 = 18µm ; ei2 = 2µm , es2 = 13µm ; EI3 = -32µm , ES3 = -14µm.
d. EI1 = 0 , ES1 = 18µm ; ei2 = -11µm , es2 = 0 ; EI3 = 22µm , ES3 = 40µm.
The correct answer is: EI1 = 0 , ES1 = 18µm ; ei2 = -11µm , es2 = 0 ; EI3 = -18µm , ES3 = 0.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 2/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Sai
According to technical requirements on the part drawing below, tolerances and limiting deviations of the widths 26 and 36 can be
determined as follows:
Select one:
a. 26±0,165 ; 36-0,390.
c. 26±0,165 ; 36±0,195.
d. 26±0,012 ; 36±0,019.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 3/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
With two given fits Ø120 and Ø120 , select the wrong sentence.
Select one:
a. The minimum limit of size for hole in the first fit is equal to the maximum limit of size for shaft in the second fit.
b. The tolerances of the holes in the two fits are the same.
c. Two fits have the same Nmax and Nmin. Your answer is
incorrect.
d. the upper deviation of the shaft in the first fit is equal to lower deviation of the hole in the second fit.
The correct answer is: the upper deviation of the shaft in the first fit is equal to lower deviation of the hole in the second fit.
Câu hỏi 5
Sai
Depending on transmission power, preferred fits for hole Ø50 of the wormgear mounted on shaft are:
Select one:
a. K6/h5 or H6/m5. Your answer is
incorrect.
b. H6/k5 or H6/m5.
c. H6/g5 or H6/js5.
d. H6/k5 or H6/h5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 4/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
Choose the hole diameter of the pulley for assembling with surface Ø70 of the shaft.
Select one:
a. D = Ø70±0,015.
c. D = Ø70+0,015.
d. D = Ø70+0,03.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 5/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Sai
Based on noticed working conditions of the below machine unit, suggest suitable fits for the components.
Select one:
a. G7/h6 for A ; N7/h6 for B.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 6/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
Based on the technical requirements, the limiting deviations of the shaft diameter Ø46 can be defined from the dimension:
Select one:
a. Ø46Js13.
c. Ø46h13.
d. Ø46H13.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 7/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Đúng
Among the following fits, select a transition fit in the bacis hole system, of which the probability of clearance is the biggest
Select one:
a. H8/k7.
c. H6/js5.
d. Js7/h6.
Câu hỏi 10
Sai
Determine the suitable dimensions for the piston and the cylinder bore in an hydraulic drive system.
Select one:
a. D = Φ100-0,022 ; d = Φ100±0,0075.
b. D = Φ100-0,022 ; d = Φ100+0,015.
d. D = Φ100+0,022 ; d = Φ100-0,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 8/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
With a given fit in the basic hole system having D = d = Ø42, Td = 26μm, Smax = 7μm, Nmax = 51μm, determine the limits of size of the hole
and the shaft.
Select one:
a. Dmax = Ø41,981 ; Dmin = Ø41,949 ; dmax = Ø42 ; dmin = Ø41,974
The correct answer is: Dmax = Ø42,032 ; Dmin = Ø42 ; dmax = Ø42,051 ; dmin = Ø42,025
Câu hỏi 12
Không trả lời
Select one:
a. D = Ø110+0,035 mm ; d = Ø110 mm
b. D =Ø24-0,033 mm ; d = Ø24-0,021 mm
c. D = Ø63+0,030 mm ; d = Ø63 mm
d. D = Ø75 mm ; d = Ø75-0,019 mm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 9/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
Choose fit for the joint between the gear and shaft diameter Ø24 of the below part
Select one:
a. F7/h6.
b. K7/h6.
c. H7/k6.
d. H7/f7.
Câu hỏi 14
Không trả lời
Select one:
a. The same Nmin and Nmax
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 10/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
If fundamental deviation of a shaft is t and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by es = Td + ei
Câu hỏi 16
Không trả lời
Fits between holes and shafts in the below figures 1 and 2 are:
Figure 1
Figure 2
Select one:
a. Ø65H7/g6 and Ø36G7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 11/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Select one:
a. Probability of interference is greater than 99%.
Câu hỏi 18
Không trả lời
Select one:
a. Transition fit in the basic hole system.
The correct answer is: Interference fit in the basic shaft system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 12/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
Among the following fits, select a transition fit in the basic shaft system, of which the probability of clearance is the biggest
Select one:
a. F7/h7.
b. Js7/h6.
c. Js6/h5.
d. K7/h6.
Câu hỏi 20
Không trả lời
With a given transition fit M7/h6, it is necessary to select another fit in order to increase the probability of interference
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 13/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Choose fit for the fixed joint between the hole Ø30 of the part and a shaft, of which the end face is clamped with the part by 3 bolts M8.
Select one:
a. Ø30H7/r6.
b. Ø30H7/f7.
c. Ø30H7/k6.
d. Ø30K7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 14/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
In the following fits, select one of which the interference is the smallest (if they have the same nominal size):
Select one:
a. P7/h6
b. T7/h6
c. P6/h5
d. R7/h6
Câu hỏi 23
Không trả lời
Select a transition fit in the basic shaft system from the following:
Select one:
a. F7/h6
b. M7/h6
c. T7/h6
d. H6/n5
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 15/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Determine a suitable fit between piston and cylindre in an internal combustion engine.
Select one:
a. G6/h5.
b. H6/k5.
c. H5/h4.
d. H7/g6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 16/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Determine suitable diameters for helical gear bore D and shaft diameter d.
Select one:
a. D = Ø40 and d = Ø40±0,008.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 17/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
To increase the interference of the fit H7/s6, one of the following fits will be selected:
Select one:
a. H7/p6 ; H8/u8 ; H7/u7.
Câu hỏi 27
Không trả lời
With two given fits Ø60U8/h7 and Ø60F8/h8, select the correct sentence.
Select one:
a. The maximum limits of the shafts in 2 fits are the same.
The correct answer is: The maximum limits of the shafts in 2 fits are the same.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 18/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
From the specified fit of Ø60H7/g6 for the diameter between the tool holder 1 and the base plate 2 of the below square tool post,
determine the limits of size of the parts in the joint.
Select one:
a. Dmin = Ø60 ; Dmax = Ø60,03 and dmin = Ø59,971 ; dmax = Ø59,99.
The correct answer is: Dmin = Ø60 ; Dmax = Ø60,03 and dmin = Ø59,971 ; dmax = Ø59,99.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 19/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
Select all interference fits in the basic hole system from the following ones.
Select one:
a. H8/u8 ; S7/h6.
b. S7/h6 ; U8/h7.
c. H8/u8.
d. H8/u8 ; H7/r6.
Câu hỏi 30
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the fit Ø45G7/h6.
Select one:
a. 4 – e.
b. 8 – e.
c. 2 – d.
d. 7 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 20/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098270&cmid=1147996 21/21
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 1/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 1
Sai
Based on noticed working conditions of dimensions E and F in the below machine unit, suggest suitable limits of sizes.
Select one:
a. Fit of dimension E: D1min = Ø12,006 ; D1max = Ø12,024 and dmin = Ø11,989 ; dmax = Ø12.
Fit of dimension F: D2min = Ø11,977 ; D2max = Ø11,995 and dmin = Ø11,989 ; dmax = Ø12.
b. Fit of dimension E: D1min = Ø12,006 ; D1max = Ø12,024 and dmin = Ø11,89 ; dmax = Ø12. Your answer is
incorrect.
Fit of dimension F: D2min = Ø11,977 ; D2max = Ø11,995 and dmin = Ø11,89 ; dmax = Ø12.
c. Fit of dimension E: D1min = Ø11,977 ; D1max = Ø11,995 and dmin = Ø11,989 ; dmax = Ø12.
Fit of dimension F: D2min = Ø12,006 ; D2max = Ø12,024 and dmin = Ø11,989 ; dmax = Ø12.
d. Fit of dimension E: D1min = Ø12,006 ; D1max = Ø12,024 and dmin = Ø12 ; dmax = Ø12,011.
Fit of dimension F: D2min = Ø11,977 ; D2max = Ø11,995 and dmin = Ø12 ; dmax = Ø12,011.
The correct answer is: Fit of dimension E: D1min = Ø12,006 ; D1max = Ø12,024 and dmin = Ø11,989 ; dmax = Ø12.
Fit of dimension F: D2min = Ø11,977 ; D2max = Ø11,995 and dmin = Ø11,989 ; dmax = Ø12.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 2/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
With a given transition fit Ø42H7/m6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. Ø42H7/js6 or Ø42H7/n6.
c. Ø42H7/k6 or Ø42H7/js6.
d. Ø42H7/js6 or Ø42K7/h6.
Câu hỏi 3
Sai
Select one:
a. Ø50H7/n6
b. Ø50H7/p6
d. Ø50H7/js6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 3/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Đúng
Select one:
a. disposed equally about the zero line.
Câu hỏi 5
Sai
Choose suitable diameters of the idler gear hole and the intermittent shaft in the speed gearbox.
Select one:
a. D = Ø20+0,021 and d = Ø20 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 4/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Đúng
If fundamental deviation of a hole is U and the hole tolerance is TD , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by ES = TD + EI.
b. lower limiting deviation that is determined by EI = TD + ES.
c. upper limiting deviation that is determined by ES = TD - EI.
d. lower limiting deviation that is determined by EI = ES - TD. Your answer is
correct.
The correct answer is: lower limiting deviation that is determined by EI = ES - TD.
Câu hỏi 7
Sai
Select the correct sentence from two fits ø36 and ø36
Select one:
a. The shaft tolerance in the first fit is equal to the hole tolerance in the second one. Your answer is
incorrect
b. The limits of size for shaft in the first fit are equal to the limits of size for hole in the second one.
c. The limits of size for hole in the first fit are equal to the limits of size for shaft in the second one.
d. The hole tolerance in the first fit is equal to the shaft tolerance in the second one.
The correct answer is: The hole tolerance in the first fit is equal to the shaft tolerance in the second one.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 5/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
Select one:
a. Figure 1: Ø100M8/h7 ; Figure 2: Ø100R7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 6/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Đúng
Sort the following fits in descending order of interference (if they have the same nominal size):
Select one:
a.
b. Your answer is
correct.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 7/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Sai
Suggest suitable fitted diameters for the components of the below spring loaded relief valse.
Select one:
a. Hole of the flange 7 is D1 = Ø12 ; hole of valse 3 is D2 = Ø12 and diameter of cylindrical stem 6 is d = Ø12-0,011.
b. Hole of the flange 7 is D1 = Ø12 ; hole of valse 3 is D2 = Ø12 and diameter of cylindrical Your answer is
stem 6 is d = Ø12-0,011. incorrect.
c. Hole of the flange 7 is D1 = Ø12 ; hole of valse 3 is D2 = Ø12-0,018 and diameter of cylindrical stem 6 is d = Ø12-0,011.
d. Hole of the flange 7 is D1 = Ø12 ; hole of valse 3 is D2 = Ø12 and diameter of cylindrical stem 6 is d = Ø12+0,011.
The correct answer is: Hole of the flange 7 is D1 = Ø12 ; hole of valse 3 is D2 = Ø12 and diameter of cylindrical stem 6 is d
= Ø12-0,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 8/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
To decrease the interference of the fit H7/r6, one of the following fits will be selected:
Select one:
a. H7/p6 ; H6/p5.
d. H7/p6 ; P7/h6.
Câu hỏi 12
Không trả lời
There are 2 fitted dimensions in a worm-and-wormwheel drive. The first fit is the one between the worm hole and the first shaft and the
second one is between the wormwheel hole and the second shaft.
Choose two proper fits.
Select one:
a. Ø30H7/k6 for the first fit and Ø45K7/h6 for the second one.
b. Ø30K7/h6 for the first fit and Ø45H7/k6 for the second one.
c. Ø30F7/h6 for the first fit and Ø45H7/k6 for the second one.
d. Ø30H7/k6 for the first fit and và Ø45H7/k6 for the second one.
The correct answer is: Ø30H7/k6 for the first fit and và Ø45H7/k6 for the second one.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 9/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
Select one:
a. From A (a) to H ( h).
Câu hỏi 14
Không trả lời
Among the following fits, select a transition fit in the bacis shaft system, of which the probability of clearance is the biggest
Select one:
a. H7/js6.
b. Js7/h6.
c. H8/k7.
d. M7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 10/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create two fits Ø45H7/f7 and Ø45S7/h6, respectively.
Select one:
a. 2 – a ; 5 – e.
b. 2 – i ; 5 – e.
c. 2 – i ; 5 – e.
d. 2 – a ; 7 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 11/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
Choose suitable fits for the joint between pin 2 and steel housing 1 as well as the joint between pin 2 and the roller pulley wheel 4.
Select one:
a. F8/h7 for the joint between pin 2 and steel housing 1 ; Js8/h7 for the joint between pin 2 and roller pulley wheel 4.
b. H8/js7 for the joint between pin 2 and steel housing 1 ; H8/f7 for the joint between pin 2 and roller pulley wheel 4.
c. Js6/h5 for the joint between pin 2 and steel housing 1 ; H5/h4 for the joint between pin 2 and roller pulley wheel 4.
d. Js8/h7 for the joint between pin 2 and steel housing 1 ; F8/h7 for the joint between pin 2 and roller pulley wheel 4.
The correct answer is: Js8/h7 for the joint between pin 2 and steel housing 1 ; F8/h7 for the joint between pin 2 and roller pulley wheel
4.
Câu hỏi 17
Không trả lời
Select one:
a. the big interference, large and impact load and only assembly and disassembly in major repairs.
c. small load and frequent assembly and disassembly to change the damaged parts.
d. the medium interference, small load and frequent assembly and disassembly such as the joint between shaft and gears.
The correct answer is: the big interference, large and impact load and only assembly and disassembly in major repairs.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 12/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/f7 and B = Ø40H7/n6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,17 ; d2max = Ø40,33.
d. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 13/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the D joint .
Select one:
a. Clearance fit in the basic shaft system.
The correct answer is: Transition fit in the basic shaft system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 14/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
Based on the technical requirements, the limiting deviations of the external cylindre Ø70 can be defined from the dimension:
Select one:
a. Φ70Js13.
b. Φ70h13.
c. Φ70js13.
d. Φ70H13.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 15/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create all interference fits in the basic hole system.
Select one:
a. 2 – f.
b. 2 – c ; 2 – h.
c. 2 – j ; 7 – e.
d. 2 – j.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 16/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
With the chosen fits for the joints in the mechanism, the dimension of the shaft 2 will be:
Select one:
a. Φ35-0,016.
b. Φ35 .
c. Φ35±0,008.
d. Φ35+0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 17/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Không trả lời
Choose fits for the impeller and the pulley that are mounted on the shaft of an industrial fan:
Select one:
a. Ø32K7/h6 for the joint between the impeller and shaft; Ø32H7/k6 for the joint between the pulley and shaft.
c. Ø32H7/k6 for the joint between the impeller and shaft; Ø32K7/h6 for the joint between the pulley and shaft.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 18/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
In order to determine the shaft diameter d = Ø20 in the below part drawing, fit between the pulley hole and the shaft must be:
Select one:
a. Ø20H7/k6.
b. Ø20K7/k6.
c. Ø20H7/h6.
d. Ø20K7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 19/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create all transition fits in the basic shaft system.
Select one:
a. 3 – e ; 6 – e ; 9 – e ; 10 – e.
b. 3 – e ; 6 – e ; 10 – e.
c. 3 – e ; 9 – e ; 10 – e.
d. 3 – e ; 6 – c ; 9 – c ; 10 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 20/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create two fits Ø45H7/f6 and Ø45P7/h6, respectively.
Select one:
a. 2 – c ; 7 – e.
b. 2 – i ; 7 – e.
c. 2 – i ; 1 – e.
d. 2 – c ; 5 – e.
Câu hỏi 27
Không trả lời
Select one:
a. D = Ø50±0,012 ; d = Ø50-0,016.
b. D = Ø50+0,025 ; d = Ø50 .
c. D = Ø50 ; d = Ø50-0,016.
d. D = Ø50 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 21/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Select a transition fit in which the probability of clearance is much bigger than the one of interference when assembling at random.
Select one:
a. D = Ø50+0,025 ; d = Ø50±0,008.
b. D = Ø50-0,025 ; d = Ø50 .
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50+0,025 ; d = Ø50 .
Câu hỏi 29
Không trả lời
Transition fits, the clearance and the interference of which are nearly the same probability, are structured as follows:
Select one:
a. H/m (in the basic hole system) or M/h (in the basic shaft system)
b. H/js (in the basic hole system) or Js/h (in the basic shaft system)
c. H/n (in the basic hole system) or N/h (in the basic shaft system)
d. H/k (in the basic hole system) or K/h (in the basic shaft system)
The correct answer is: H/k (in the basic hole system) or K/h (in the basic shaft system)
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 22/23
10/20/23, 4:09 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Choose the diagram of tolerance disposition of transition fit in the basic hole system from the following ones:
Select one:
a. Diagram 1
b. Diagram 2
c. Diagram 3
d. Diagram 4
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098261&cmid=1147996 23/23
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Đúng
Select transition fits in the basic shaft system among the following ones:
Select one:
a. M7/h6, Js5/h4 and N8/h7 Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 1/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Among the following fits, select one in the basic hole system, of which the interference is the biggest (if they have the same nominal
size):
Select one:
a. H7/t6.
c. H8/u8.
d. U8/h7.
Câu hỏi 3
Sai
To decrease the interference of the fit H7/s6, one of the following fits will be selected:
Select one:
a. H7/p6 ; H7/h6.
b. H7/p6 ; P7/h6.
d. H7/p6 ; H7/r6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 2/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
From the following fits, select one of which the clearance is the biggest:
Select one:
a. G6/h5
c. E8/h7
d. H8/n7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 3/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Sai
Choose a suitable fit between the outer diameter of plain bearing and the hole of Ø18+0,018 in the part drawing:
Select one:
a. Ø18H7/js6.
c. Ø18Js7/h6.
d. Ø18H7/n6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 4/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
From specified fits on the below assembly drawing, determine dimensions of the different parts in the cluster.
Select one:
a. Ø10F8: dimension of the holes in the piston ; Ø10Js8: dimension of the small end hole of the connecting rod ; Ø10h7:
dimension of the piston pin.
b. Ø10F8: dimension of the holes in the piston ; Ø10h7: dimension of the small end hole of Your answer is
the connecting rod ; Ø10Js8: dimension of the piston pin. incorrect.
c. Ø10Js8: dimension of the holes in the piston ; Ø10F8: dimension of the small end hole of the connecting rod ; Ø10h7:
dimension of the piston pin.
d. Ø10h7: dimension of the holes in the piston ; Ø10Js8: dimension of the small end hole of the connecting rod ; Ø10F8:
dimension of the piston pin.
The correct answer is: Ø10Js8: dimension of the holes in the piston ; Ø10F8: dimension of the small end hole of the connecting rod
; Ø10h7: dimension of the piston pin.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 5/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Sai
Choose the outer diameter d of plain bearing assembled with hole D of "a rocker arm" in an internal combustion engine.
Select one:
a. d = Ø35-0,016 ; D = Ø35+0,025.
c. d = Ø35 ; D = Ø35-0,025.
d. d = Ø35 ; D = Ø35+0,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 6/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Đúng
Select one:
a. Ø65H7/g6.
c. Ø65G7/h6.
d. Ø65H7/p6.
Câu hỏi 9
Sai
A fit in the basic hole system with Smax = 23μm, TD = 30µm, Td = 35µm. Determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø42,030 ; Dmin = Ø42 ; dmax = Ø42,07 ; dmin = Ø41,72.
d. Dmax = Ø41,988 ; Dmin = Ø41,958 ; dmax = Ø42,035 ; dmin = Ø42. Your answer is
incorrect.
The correct answer is: Dmax = Ø42,030 ; Dmin = Ø42 ; dmax = Ø42,007 ; dmin = Ø41,972.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 7/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Sai
Select one:
a. Figure 1: K7/h6 ; Figure 2: H7/p6.
Câu hỏi 11
Không trả lời
From the assembly drawing, determine hole dimensions of the components 1 and 3 in the machine cluster as follows:
Select one:
a. Φ18±0,009 : hole diameter of the part 3 ; Φ18+0,018 : hole diameter of the part 1.
b. Φ18 : hole diameter of the part 3 ; Φ18-0,018 : hole diameter of the part 1.
c. Φ18 : hole diameter of the part 3 ; Φ18+0,018 : hole diameter of the part 1.
d. Φ18±0,009 : hole diameter of the part 3 ; Φ18-0,018 : hole diameter of the part 1.
The correct answer is: Φ18±0,009 : hole diameter of the part 3 ; Φ18+0,018 : hole diameter of the part 1.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 8/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Due to the plain bearing mounted into hole Ø24 of the below part, the following fit will be selected for the outer diameter of the plain
bearing and hole Ø24:
Select one:
a. Ø24S7/n6.
b. Ø24H7/n6.
c. Ø24H7/s6.
d. Ø24N7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 9/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
From the chosen fit between the outer diameter of the plain bearings and the holes of Ø16 in the below part drawing, determine the hole
diameter D of the part holes and outer diameter d of the plain bearings.
Select one:
a. D = Ø16+0,018 ; d = Ø16 .
b. D = Ø16+0,018 ; d = Ø16-0,011.
c. D = Ø16±0,009 ; d = Ø16 .
d. D = Ø16±0,009 ; d = Ø16±0,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 10/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
Choose suitable diameters of the idler gear hole and the intermittent shaft in the speed gearbox.
Select one:
a. D = Ø40+0,025 ; d = Ø40 .
b. D = Ø40+0,025 ; d = Ø40 .
c. D = Ø40 ; d = Ø40-0,016.
d. D = Ø40+0,025 ; d = Ø40 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 11/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
From the fit between sleeves and shaft portions 2, 5 of an intermittent shaft in a double reduction gearbox, determine limits of sizes of
sleeve bore and shaft.
Select one:
a. Dmin = Ø44,961 , Dmax = Ø45 ; and dmin = Ø45 , dmax = Ø45,025.
The correct answer is: Dmin = Ø45 , Dmax = Ø45,039 ; and dmin = Ø44,950 , dmax = Ø44,975.
Câu hỏi 16
Không trả lời
Disposition diagrams of the tolerance position in the below picture belong to the following fits in respectively:
Select one:
a. R7/h6 ; H7/n7 ; H7/js7 ; K8/h7
b. H7/js7 ; K8/h7 ; R7/h6 ; H7/n7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 12/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
From the assembly drawing of the cluster in a reduction gear box, determine hole diameter D of gear 7 and diameter d of the shaft 1.
Select one:
a. D = Ø28+0,021 and d = Ø28 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 13/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Determine the limits of sizes for fit between the piston and the cylinder bore in an hydraulic drive system.
Select one:
a. Dmin = Ø64,981 ; Dmax = Ø65 and dmin = Ø64,987 ; dmax = Ø65.
The correct answer is: Dmin = Ø65 ; Dmax = Ø65,019 and dmin = Ø64,987 ; dmax = Ø65.
Câu hỏi 19
Không trả lời
From the fit Ø30N8/h7 on assembly drawing, determine limits of sizes of hole and shaft.
Select one:
a. Dmin = Ø29,967 ; Dmax = Ø30 and dmin = Ø29,979 ; dmax = Ø30.
The correct answer is: Dmin = Ø29,964 ; Dmax = Ø29,997 and dmin = Ø29,979 ; dmax = Ø30.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 14/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
Select a fit having the most clearance from the following ones (if they have the same nominal size):
Select one:
a.
b.
c.
d.
Câu hỏi 21
Không trả lời
Suggest limits of size for sleeve bore 8 and shaft 2 on the assembly drawing.
Select one:
a. Dmin = Ø39,961 , Dmax = Ø40 ; and dmin = Ø40 , dmax = Ø40,025.
The correct answer is: Dmin = Ø40 , Dmax = Ø40,039 ; and dmin = Ø39,950 , dmax = Ø39,975.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 15/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Select one:
a. Probability of interference and probability of clearance are approximately equal.
Câu hỏi 23
Không trả lời
Among the following fits, select a transition fit in the basic shaft system, of which the probability of interference is the biggest
Select one:
a. N7/h6.
b. T7/h6.
c. M7/h6.
d. K7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 16/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Based on noticed working conditions of dimensions E in the below machine unit, suggest suitable limits of sizes.
Select one:
a. Dmin = Ø14,006 ; Dmax = Ø14,024 and dmin = Ø13,989 ; dmax = Ø14.
The correct answer is: Dmin = Ø14,006 ; Dmax = Ø14,024 and dmin = Ø13,989 ; dmax = Ø14.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 17/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
If fundamental deviation of a hole is T and the hole tolerance is TD , non-fundamental deviation is:
Select one:
a. lower limiting deviation that is determined by EI = TD + ES.
b. upper limiting deviation that is determined by ES = TD - EI.
c. lower limiting deviation that is determined by EI = ES - TD.
d. upper limiting deviation that is determined by ES = TD + EI.
The correct answer is: lower limiting deviation that is determined by EI = ES - TD.
Câu hỏi 26
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create two fits Ø45G7/h6 and Ø45H7/n6, respectively.
Select one:
a. 8 – e ; 2 – h.
b. 4 – e ; 2 – b.
c. 4 – e ; 7 – e.
d. 4 – e ; 2 – h.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 18/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
With a given transition fit Ø45N7/h6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. Ø45Js7/h6 or Ø45H7/m6.
b. Ø45Js7/h6 or Ø45H7/k6.
c. Ø45K7/h6 or Ø45F7/h6.
d. Ø45K7/h6 or Ø45M7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 19/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
From the assembly drawing of the cluster in a reduction gear box, determine type of fit between the hole diameter D of housing 5 and
diameter d of the cover 3.
Select one:
a. Clearance fit in the basic shaft system.
The correct answer is: Clearance fit in the basic hole system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 20/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
From the given fits on the assembly drawing, determine cone gear bore D and shaft diameter d.
Select one:
a. D = Ø36+0,025 and d = Ø36-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 21/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Among the following fits, select a transition fit, of which the probability of interference is the biggest
Select one:
a. H7/m6.
b. H7/n6.
c. H8/k7.
d. M7/h6.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098252&cmid=1147996 22/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Đúng
Collect all clearance fits in the basic hole system from the following:
Select one:
a. H7/g6 ; H7/f7 ; H8/e8.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 1/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Choose a suitable fit between the slot 28 of the below housing and the key of the machine table:
Select one:
a. H7/f7.
c. H6/h5.
d. H6/t5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 2/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Sai
Sort the following fits in ascending order of interference (if they have the same nominal size):
Select one:
a.
b. Your answer is
incorrect.
c.
d.
Câu hỏi 4
Sai
If fundamental deviation of a hole is E and the hole tolerance is TD , non-fundamental deviation is:
Select one:
a. lower limiting deviation that is determined by EI = ES - TD.
b. upper limiting deviation that is determined by ES = TD - EI. Your answer is
incorrect.
The correct answer is: upper limiting deviation that is determined by ES = TD + EI.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 3/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Đúng
Select one:
a. The same maximum limit of size for holes.
The correct answer is: The same maximum limit of size for shafts.
Câu hỏi 6
Sai
Sort the following fits in ascending order of interference (if they have the same nominal size):
Select one:
a.
b.
c. Your answer is
incorrect.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 4/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Sai
Transition fits, the interference probability of which is more than 99%, are structured as follows:
Select one:
a. H/js (in the basic hole system) or Js/h (in the basic shaft system)
b. H/n (in the basic hole system) or N/h (in the basic shaft system)
c. H/k (in the basic hole system) or K/h (in the basic shaft system) Your answer is
incorrect
d. H/m (in the basic hole system) or M/h (in the basic shaft system)
The correct answer is: H/n (in the basic hole system) or N/h (in the basic shaft system)
Câu hỏi 8
Sai
Transition fits in the basic shaft system are created by fundamental deviations as follows:
Select one:
a. From J to N.
b. From j to n.
d. From p to zc.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 5/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Sai
Suggest limits of size for gear bore 3 and shaft 2 on the assembly drawing.
Select one:
a. Dmin = Ø29,979 , Dmax = Ø30 ; and dmin = Ø29,9935 , dmax = Ø30,0065.
The correct answer is: Dmin = Ø30 , Dmax = Ø30,021 ; and dmin = Ø30,002 , dmax = Ø30,015.
Câu hỏi 10
Sai
Select one:
a. D1 - D3 - D2 - D4
b. D1 - D2 - D3 - D4 Your answer is
incorrect.
c. D4 - D2 - D3 - D1
d. D4 - D1 - D3 - D2
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 6/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Đúng
Select all interference fits in the basic shaft system from the following ones.
Select one:
a. S7/h6 ; U8/h7. Your answer is
correct.
b. U8/h7.
c. H8/u8 ; H7/r6.
d. H8/u8 ; S7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 7/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Based on noticed working conditions of the below machine unit, suggest suitable fits for E and F of the components.
Select one:
a. H7/js6 for E; H7/s6 for F.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 8/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
To increase the clearance of the fit F7/h6, one of the following fits will be selected:
Select one:
a. F8/h6 ; F8/h7 ; E8/h8
Câu hỏi 14
Không trả lời
Select one:
a. Ø10±0,011.
b. Ø10±0,11.
c. Ø10+0,015.
d. Ø10-0,022.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 9/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Choose proper fit between helical gears and shaft portions 3, 4 of an intermittent shaft in a double reduction gearbox.
Select one:
a. Ø50K7/h6.
b. Ø50H7/n6.
c. Ø50H7/f7.
d. Ø50H7/k6.
Câu hỏi 16
Không trả lời
With a series of given shafts having d = Ø125 , choose the size of the holes D so that when assembled, it will create an interference
fit in the basic hole system
Select one:
a. D = Ø125-0,025.
b. D = Ø125+0,025.
c. D = Ø125
d. D = Ø125±0,012.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 10/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
With a series of given shafts having d = Ø72±0,0095 , choose the size of the holes D so that when assembled, it will create a transition fit
in the basic hole system
Select one:
a. D = Ø72+0,030.
b. D = Ø72
c. D = Ø72-0,030.
d. D = Ø72±0,015.
Câu hỏi 18
Không trả lời
From the assembly drawing, determine limitimg deviations of the component dimensions 1, 2 and 3 (D = d = Ø55) in the machine cluster
as follows:
Select one:
a. EI1 = -30µm , ES1 = 0µm ; ei2 = -9,5µm , es2 = 9,5µm ; EI3 = -30µm , ES3 = 0.
b. EI1 = 0 , ES1 = 30µm ; ei2 = 2µm , es2 = 18µm ; EI3 = -42µm , ES3 = -17µm.
c. EI1 = 0 , ES1 = 30µm ; ei2 = -19µm , es2 = 0 ; EI3 = 34µm , ES3 = 50µm.
The correct answer is: EI1 = 0 , ES1 = 30µm ; ei2 = -19µm , es2 = 0 ; EI3 = -30µm , ES3 = 0.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 11/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
From the assembly drawing of the cluster in a reduction gear box, determine hole diameter D of housing 5 and diameter d of the cover 3.
Select one:
a. D = Ø62+0,030 and d = Ø62 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 12/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
From the assembly drawing of the cluster in a reduction gear box, determine hole diameter D of gear 7 and diameter d of the shaft 1.
Select one:
a. Dmin = Ø28 ; Dmax = Ø28,012 and dmin = Ø28,002 ; dmax = Ø28,015.
The correct answer is: Dmin = Ø28 ; Dmax = Ø28,021 and dmin = Ø28,002 ; dmax = Ø28,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 13/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Based on noticed working conditions of the below machine unit, suggest suitable limits of size for dimension C between bush and gear
bore in the below mechanism.
Select one:
a. Dmin = Ø30 ; Dmax = Ø30,021 and dmin = Ø29,980 ; dmax = Ø29,993.
The correct answer is: Dmin = Ø30 ; Dmax = Ø30,021 and dmin = Ø30,015 ; dmax = Ø30,028.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 14/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
To increase the interference of the fit S7/h6, one of the following fits will be selected:
Select one:
a. H7/t6 ; H7/u6.
b. H7/p6 ; T7/h6.
c. T7/h6 ; U7/h6.
d. T7/p6 ; H7/u6.
Câu hỏi 23
Không trả lời
Select one:
a. Transition fit in the basic shaft system.
The correct answer is: Transition fit in the basic shaft system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 15/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Select one:
a. D4
b. D1
c. D2
d. D3
Câu hỏi 25
Không trả lời
With a given transition fit M7/h6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. K7/h6
b. P7/h6
c. N7/h6
d. F7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 16/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Select all clearance fits in the basic shaft system from the following ones:
Select one:
a. H6/h5 ; E8/h7 ; G6/h5.
c. E8/h7 ; G6/h5.
Câu hỏi 27
Không trả lời
Select one:
a. From 5 -> 11.
b. From 01 -> 4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 17/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
From the fit between sleeves and shaft portions 2, 5 of an intermittent shaft in a double reduction gearbox, determine dimensions of
sleeve bore and shaft.
Select one:
a. D = Ø45±0,019 and d = Ø45 .
Câu hỏi 29
Không trả lời
Sort three following parts in ascending order of accuracy : d1 = Ø200 +0,029 mm, D2 = Ø120± 0,027 mm , D3 = Ø50-0,025 mm .
Select one:
a. D1 ; D3 ; D2
b. D1 ; D2 ; D3
c. D2 ; D1 ; D3
d. D2 ; D3 ; D1
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 18/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Select one:
a. Figure 1: transition fit in the basic shaft system; Figure 2: interference fit in the basic shaft system.
b. Figure 1: transition fit in the basic hole system; Figure 2: clearance fit in the basic shaft system.
c. Figure 1: interference fit in the basic shaft system; Figure 2: transition fit in the basic shaft system.
d. Figure 1: transition fit in the basic shaft system; Figure 2: clearance fit in the basic shaft system.
The correct answer is: Figure 1: transition fit in the basic shaft system; Figure 2: interference fit in the basic shaft system.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098240&cmid=1147996 19/19
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 1/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 1
Đúng
From the given fits on the assembly drawing, determine outside and inside diameters of sleeve 27.
Select one:
a. Ø80+0,030 and Ø68-0,019.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 2/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
To reduce the clearance of the fit H7/f7, the following fit will be selected:
Select one:
a. H7/k6
c. H7/g6
d. G7/h6
Câu hỏi 3
Sai
Select one:
a. Ø100N8/h7. Your answer is
incorrect
b. Ø100S8/h7.
c. Ø100M8/h7.
d. Ø100H8/m7.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 3/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Select one:
a. D = Ø50 ; d = Ø50-0,016.
b. D = Ø50±0,012 ; d = Ø50-0,016.
d. D = Ø50 ; d = Ø50 .
Câu hỏi 5
Sai
Among the following fits, select a transition fit in the basic shaft system, of which the probability of interference is the biggest:
Select one:
a. M7/h6 Your answer is
incorrect.
b. N8/h7
c. H6/k5
d. Js5/h4
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 4/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Đúng
Choose fit between worm gear bore and stepped shaft in a worm gear reducer.
Select one:
a. Ø40H7/k6. Your answer is
correct.
b. Ø40K7/h6.
c. Ø40H7/f7.
d. Ø40F7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 5/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Sai
Due to the plain bearings mounted into holes Ø16 of the below part, the following fit will be selected for the outer diameter of the plain
bearings and holes Ø16:
Select one:
a. Ø16H7/n6.
c. Ø16H7/s6.
d. Ø16N7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 6/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
Transition fits, the clearance and the interference of which are nearly the same probability, are structured as follows:
Select one:
a. H7/k6 or K7/h6
c. H7/n6 or N7/h6
d. H7/js6 or Js7/h6
Câu hỏi 9
Sai
With a given transition fit H7/m6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. H7/r6
c. H7/n6
d. H7/js6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 7/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Sai
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/f7 and B = Ø42H7/m6.
Select one:
a. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980. Your answer is
incorrect.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,09 ; d2max = Ø42,25.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
d. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,979 ; d1max = Ø30.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
Câu hỏi 11
Sai
To reduce the clearance of the fit F7/h6, one of the following fits will be reselected:
Select one:
a. G7/h6 or H7/h6.
d. H7/h6 or H7/g6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 8/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Sai
Match diameters of hole and shaft in the two following columns in order to create two fits Ø45K7/h6 and Ø45H7/e7, respectively.
Select one:
a. 9 – e ; 2 – c.
b. 3 – e ; 2 – c. Your answer is
incorrect.
c. 9 – e ; 2 – a.
d. 7 – e ; 2 – c.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 9/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Đúng
Choose suitable diameters for the fit between worm gear bore D and stepped shaft d in a worm gear reducer.
Select one:
a. D = Ø28-0,021 and d = Ø28±0065.
Câu hỏi 14
Sai
Select one:
a. D = Ø50±0,012 ; d = Ø50 .
b. D = Ø50 ; d = Ø50-0,016.
d. D = Ø50±0,012 ; d = Ø50-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 10/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Sai
With the chosen fits for the joints in the mechanism, the dimension of the shaft 2 will be:
Select one:
a. Φ55 .
c. Φ55-0,019.
d. Φ55+0,019.
Câu hỏi 16
Đúng
From the fit Ø30N8/h7 on assembly drawing, determine dimensions of hole and shaft.
Select one:
a. Ø30-0,021 for hole and Ø30 for shaft.
The correct answer is: Ø30 for hole and Ø30-0,021 for shaft.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 11/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Đúng
Based on noticed working conditions of dimensions A and B in the below machine unit, suggest suitable limits of sizes.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993. Your answer is
correct.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,17 ; d2max = Ø40,33.
c. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
d. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 12/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Sai
Among the following fits, select a transition fit, of which the probability of interference is the smallest :
Select one:
a. H6/k5 Your answer is
incorrect.
b. N8/h7
c. Js5/h4
d. M7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 13/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Sai
Based on noticed working conditions of the below machine unit, suggest suitable limits of size for dimension B between bush and housing
in the below mechanism.
Select one:
a. Dmin = Ø39,967 ; Dmax = Ø39,992 and dmin = Ø39,984 ; dmax = Ø40. Your answer is
incorrect.
The correct answer is: Dmin = Ø40 ; Dmax = Ø40,025 and dmin = Ø40,017 ; dmax = Ø40,033.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 14/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Sai
From the fit between the plain bearing and shaft on the assembly drawing, determine the limits of size of the bearing hole and shaft.
Select one:
a. Dmin = Ø39,961 , Dmax = Ø40 ; and dmin = Ø39,984 , dmax = Ø40.
b. Dmin = Ø39,961 , Dmax = Ø40 ; and dmin = Ø40 , dmax = Ø40,016. Your answer is
incorrect.
The correct answer is: Dmin = Ø40,025 , Dmax = Ø40,064 ; and dmin = Ø39,984 , dmax = Ø40.
Câu hỏi 21
Đúng
With given holes having D = Ø24+0,021, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. d = Ø24+0,013.
b. d = Ø24±0,0065.
d. d = Ø24 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 15/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Sai
Among the following fits, select one in the basic hole system of which the clearance is the biggest:
Select one:
a. H8/f7
c. H6/h5
d. E8/h7
Câu hỏi 23
Sai
With two given fits Ø36H8/k7 and Ø36H7/s6, select the correct sentence.
Select one:
a. The minimum limits of the holes in 2 fits are the same.
c. The maximum limits of the shafts in 2 fits are the same. Your answer is
incorrect.
The correct answer is: The minimum limits of the holes in 2 fits are the same.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 16/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Sai
From the assembly drawing of the cluster in a reduction gear box, determine hole diameter D of the oil seal 8 and diameter d of the shaft 1.
Select one:
a. Dmin = Ø25 ; Dmax = Ø25,013 and dmin = Ø25,002 ; dmax = Ø25,015. Your answer is
incorrect.
The correct answer is: Dmin = Ø25 ; Dmax = Ø25,033 and dmin = Ø25,002 ; dmax = Ø25,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 17/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Đúng
If fundamental deviation of a hole is S and the hole tolerance is TD , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by ES = TD - EI.
b. lower limiting deviation that is determined by EI = ES - TD. Your answer is
correct.
The correct answer is: lower limiting deviation that is determined by EI = ES - TD.
Câu hỏi 26
Sai
If fundamental deviation of a shaft is r and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. lower limiting deviation that is determined by ei = es - Td
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 18/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Sai
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the E joint .
Select one:
a. Transition fit in the basic hole system. Your answer is
incorrect.
The correct answer is: Clearance fit in the basic shaft system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 19/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Sai
From the fit Ø120H7/k6 on assembly drawing, determine dimensions of hole and shaft.
Select one:
a. Ø120 for hole and Ø120+0,35 for shaft.
The correct answer is: Ø120+0,035 for hole and Ø120 for shaft.
Câu hỏi 29
Đúng
Select one:
a. Grades from 12 to 18
b. Grades from 5 to 18
c. Grades from 01 to 4.
d. Grades from 5 to 11 Your answer is
correct
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 20/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Đúng
In the below reducing gearbox, fits for the fixed joints between gears and shafts can be choosen as follows :
Select one:
a. H7/k6 or H6/g5.
c. H6/h5 or H7/f6.
d. H6/h5 or H7/n6.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924105&cmid=1147996 21/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Sai
Select one:
a. D1
b. D3 Your answer is
incorrect.
c. D2
d. D4
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 1/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Select one:
a. D = Ø63+ 0,030 mm ; d = Ø63 mm
Câu hỏi 3
Đúng
Select one:
a. Fits for many holes on a plain shaft with the same clearance.
b. Fits for many precision holes on a plain shaft with the same interference.
c. Fit for the outer race of bearing in housing bore. Your answer is
correct.
The correct answer is: Fit for the outer race of bearing in housing bore.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 2/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Select the correct sentence from two fits Ø25H7/g6 and Ø105G7/h6:
Select one:
a. the upper limiting deviations of 2 holes are the same.
b. the lower limiting deviation of the first hole is equal to the upper limiting deviation of the second shaft.
c. the upper limiting deviation of the first hole is equal to the lower limiting deviation of the second shaft. Your answer is
incorrect.
The correct answer is: the lower limiting deviation of the first hole is equal to the upper limiting deviation of the second shaft.
Câu hỏi 5
Đúng
If fundamental deviation of a hole is G and the hole tolerance is TD , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by ES = TD - EI.
b. upper limiting deviation that is determined by ES = TD + EI. Your answer is
correct.
The correct answer is: upper limiting deviation that is determined by ES = TD + EI.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 3/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
Based on noticed working conditions of the below machine unit, suggest suitable dimensions A between bush bore and shaft in the below
mechanism.
Select one:
a. D = Ø30-0,021 and d = Ø30 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 4/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Sai
In a reducing gearbox, fit for a fixed joint between a gear and a shaft can be choosen as follows :
Select one:
a. H6/h5 or H7/f6.
b. H7/k6 or H6/k5
d. H6/h5 or H7/n6.
Câu hỏi 8
Đúng
Select one:
a. Stb = 150μm
b. Stb = 200μm
c. Stb = 80μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 5/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Đúng
In order to determine the shaft diameter d = Ø35 in the below part drawing, fit between the gear hole and the shaft must be:
Select one:
a. Ø35K7/h6.
c. Ø35H7/h6.
d. Ø35K7/k6.
Câu hỏi 10
Sai
Select one:
a. Grades from 5 to 18
b. Grades from 5 to 11 Your answer is
incorrect
c. Grades from 12 to 18
d. Grades from 01 to 4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 6/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Sai
Determine the fit for the piston and the cylinder bore in an hydraulic drive system
Select one:
a. G6/h5.
c. H6/h5.
d. H7/p6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 7/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Sai
Choose proper outer diameter of plain bearing in order to assemble with hole Ø18 of the below connecting rod.
Select one:
a. Ø18 . Your answer is
incorrect.
b. Ø18 .
c. Ø18-0,011.
d. Ø18±0,0055.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 8/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Sai
Disposition diagram of the tolerance zone for the fit Φ90R7/h6 is:
Select one:
a. Diagram 4
b. Diagram 2 Your answer is
incorrect.
c. Diagram 3
d. Diagram 1
Câu hỏi 14
Sai
With given holes having D = Ø24+0,021, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of clearance is greater than that of interference.
Select one:
a. d = Ø24±0,0065.
b. d = Ø24 .
d. d = Ø24+0,013.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 9/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Sai
With two given fits Ø65K7/h6 and Ø65H7/k6, select the wrong sentence.
Select one:
a. The two hole tolerances are the same.
b. The maximum limit of size for the shaft in the first fit is equal to the minimum limit for the hole in the Your answer is
second fit. incorrect.
d. The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
The correct answer is: The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
Câu hỏi 16
Đúng
Match diameters of hole and shaft in the two following columns in order to create all interference fits in the basic shaft system.
Select one:
a. 3 – e ; 10 – d.
b. 1 – e ; 5 – e ; 7 – e. Your answer is
correct.
c. 1 – e ; 5 – d ; 8 – d.
d. 1 – e ; 5 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 10/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Sai
With two given fits Ø45M7/h6 and Ø45H7/m6, select the wrong sentence.
Select one:
a. The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
b. Smax and Nmax of two fits are the same. Your answer is
incorrect.
c. The maximum limit of size for the shaft in the first fit is equal to the minimum limit for the hole in the second fit.
The correct answer is: The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
Câu hỏi 18
Sai
With two given fits Ø100H7/r6 and Ø100S7/r6, select the wrong sentence.
Select one:
a. The minimum limit of size for hole in the first fit is equal to the maximum limit of size for shaft in the Your answer is
second fit. incorrect.
c. The tolerances of the holes in the two fits are the same.
d. the upper deviation of the shaft in the first fit is equal to lower deviation of the hole in the second fit.
The correct answer is: the upper deviation of the shaft in the first fit is equal to lower deviation of the hole in the second fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 11/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Đúng
Select one:
a. Ø45R7/h6. Your answer is
correct
b. Ø45P7/h6.
c. Ø45H7/p6.
d. Ø45H7/r6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 12/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Sai
Choose proper dimensions between V pulley wheel hole D and shaft d in the below industrial fan.
Select one:
a. D = Ø32+0,025 ; d = Ø32 . Your answer is
incorrect.
b. D = Ø32+0,025 ; d = Ø32-0,016.
c. D = Ø32±0,012 ; d = Ø32-0,016.
d. D = Ø32+0,025 ; d = Ø32 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 13/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Đúng
Choose suitable diameters for the fit between worm gear bore D and stepped shaft d in a worm gear reducer.
Select one:
a. D = Ø32-0,025 and d = Ø32 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 14/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Sai
According to technical requirements on the part drawing below, tolerances and limiting deviations of outer diameters Ø60 and Ø36 can be
determined as follows:
Select one:
a. Ф60-0,046 ; Ф36-0,039.
c. Ф60-0,460 ; Ф36-0,390.
d. Ф60±0,230 ; Ф36-0,390.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 15/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Sai
Collect interference fits in the basic shaft system from the following:
Select one:
a. U8/h7 and M7/h6 Your answer is
incorrect
d. T7/h6
Câu hỏi 24
Sai
From the fit Ø45G7/h6 on assembly drawing, determine dimensions of hole and shaft.
Select one:
a. Ø45-0,016 for hole and Ø45 for shaft.
The correct answer is: Ø45 for hole and Ø45-0,016 for shaft.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 16/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Sai
From the fit between the V-belt pulley and the shaft on the assembly drawing, determine the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø35,975 , Dmax = Ø36 ; and dmin = Ø35,992 , dmax = Ø36,008. Your answer is
incorrect.
The correct answer is: Dmin = Ø36 , Dmax = Ø36,025 ; and dmin = Ø36,002 , dmax = Ø36,018.
Câu hỏi 26
Sai
Select one:
a. From J (j) to N .
b. From A (a) to G (g). Your answer is
incorrect.
c. From A (a) to H .
d. From P (p) to ZC (zc).
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 17/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Sai
In order to get dimensions Ø25 and Ø36 on the part drawing, fits which are chosen between shaft and other parts (pulley in section A-A
and bevel gear in B-B) on the assembly drawing must be:
Select one:
a. Ø25H7/k6 and Ø36H7/k6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 18/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Đúng
Match diameters of hole and shaft in the two following columns in order to create all transition fits in the basic hole system.
Select one:
a. 2 – b ; 2 – d ; 2 – g ; 2 – h. Your answer is
correct.
b. 2 – b ; 2 – d ; 2 – e ; 2 – g ; 2 – h.
c. 2 – b ; 2 – d ; 2 – f ; 2 – i.
d. 2 – b ; 2 – c ; 2 – e ; 2 – f ; 2 – h.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 19/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Sai
Based on noticed working conditions of the below machine unit, suggest suitable fits for the components.
Select one:
a. N7/h6 for E ; G7/h7 for F. Your answer is
incorrect.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 20/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Sai
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/g6 and B = Ø40H7/n6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,17 ; d2max = Ø40,33.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30. Your answer is
incorrect.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
c. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
d. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923628&cmid=1147996 21/21
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Đúng
With two given fits Ø80G7/h6 and Ø80H7/g6, select the wrong sentence.
Select one:
a. The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit. Your answer is
correct.
c. The maximum limit of size for the shaft in the first fit is equal to the minimum limit for the hole in the second fit.
The correct answer is: The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 1/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Đúng
When designing the helical gearbox, tolerance of center distance between two shafts should be choosen:
Select one:
a. 190±0,08. Your answer is
correct.
b. 190-0,18.
c. 190±0,18.
d. 190-0,08.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 2/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Đúng
Select the suitable fit between pulley hole and shaft diameter of Ø70 in the part drawing.
Select one:
a. Ø70K7/h6.
c. Ø70R7/h6.
d. Ø70H7/r6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 3/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
To increase the clearance of the fit H7/f7, one of the following fit will be reselected:
Select one:
a. H7/e7 ; H7/e8 or F8/h7. Your answer is
incorrect.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 4/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Đúng
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the C joint .
Select one:
a. Clearance fit in the basic hole system.
The correct answer is: Transition fit in the basic hole system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 5/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
Sort the following fits in descending order of clearance (if they have the same nominal size):
Select one:
a.
b. Your answer is
incorrect.
c.
d.
Câu hỏi 7
Sai
Among the following fits, select one in the basic shaft system, of which the clearance is the biggest (if they have the same nominal size):
Select one:
a. F7/h6. Your answer is
incorrect.
b. D9/h8.
c. H8/e8.
d. E9/h8.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 6/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
With a given fit in the basic shaft system having D = d = Ø28, TD = 21μm, Nmin= 7μm, Nmax= 41μm, determine the limits of size
of the hole and the shaft.
Select one:
a. Dmax = Ø27,80 ; Dmin = Ø27,59 ; dmax = Ø28 ; dmin = Ø27,987
b. Dmax = Ø27,98 ; Dmin = Ø27,059 ; dmax = Ø28 ; dmin = Ø27,087 Your answer is
incorrect.
The correct answer is: Dmax = Ø27,98 ; Dmin = Ø27,959 ; dmax = Ø28 ; dmin = Ø27,987
Câu hỏi 9
Sai
Select one:
a. Ø50F7/h6
c. Ø50H6/f6
d. Ø50M6/h5
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 7/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Sai
Select one:
a. Ø36G7/h6.
c. Ø36R7/h6.
d. Ø36H7/g6.
Câu hỏi 11
Sai
With two given fits ø100H7/k6 and ø100M6/h5, select the correct sentence.
Select one:
a. The limits of shaft of the first fit are equal to the limits of hole of the second one.
b. The shaft tolerance of the first fit is equal to the hole tolerance of the second one.
c. The hole tolerance of the first fit is equal to the shaft tolerance of the second one. Your answer is
incorrect
d. The limits of hole of the first fit are equal to the limits of shaft of the second one.
The correct answer is: The shaft tolerance of the first fit is equal to the hole tolerance of the second one.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 8/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Sai
Select one:
a. D = Ø36+0,025 and d = Ø36-0,016. Your answer is
incorrect
Câu hỏi 13
Sai
A fit has the following data Td = 28μm, Smax = 46μm, hole lower deviation equals 0, bilateral tolerance of shaft. Calculate the hole and
shaft limiting deviations.
Select one:
a. ES = 14μm, EI = - 14μm, es = 28μm, ei = 0
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 9/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Sai
The outline of disposition diagram of tolerance zones for fit H6/js5 is:
Select one:
a.
b.
c.
d. Your answer is
incorrect.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 10/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Sai
Choose the suitable shaft d in order to assemble with hole of the worn gear D = ø80H7.
Select one:
a. d = Ø80 .
b. d = Ø80 .
d. d = Ø80+0,19.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 11/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Đúng
Select one:
a. fully above the zero line. Your answer is
correct.
Câu hỏi 17
Sai
With the number of holes and shafts N = 10.000 pcs in the below transition fit, compare the probability of clearance and interference of the
fit.
Select one:
a. Probability of clearance is three times greater than probability of interference. Your answer is
incorrect
The correct answer is: Probability of interference is much greater than probability of clearance.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 12/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Sai
With a given transition fit in the basic shaft system, in order to change Nmax it is necessary to reselect:
Select one:
a. The tolerance grades of hole and shaft.
The correct answer is: The fundamental deviation of hole or tolerance grade of hole.
Câu hỏi 19
Đúng
Among the following fits, select transition fit(s) of which the probability of clearance is the biggest
Select one:
a. H8/k7.
c. H7/m6 ; M7/h6.
d. Js7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 13/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Sai
Among the following fits, select a transition fit in the basic hole system, of which the probability of clearance is the biggest
Select one:
a. H7/h6.
c. H7/js6.
d. H8/n7.
Câu hỏi 21
Sai
With given holes having D = Ø110 , choose the size of the shafts d so that when assembled, it will create a transition fit having
Smax = 15µm
Select one:
a.
b. Your answer is
incorrect
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 14/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Đúng
From the fit Ø120H7/k6 on assembly drawing, determine limits of sizes of hole and shaft.
Select one:
a. Dmin = Ø120,003 ; Dmax = Ø120,025 and dmin = Ø120 ; dmax = Ø120,035.
b. Dmin = Ø120 ; Dmax = Ø120,035 and dmin = Ø120,003 ; dmax = Ø120,025. Your answer is
correct.
The correct answer is: Dmin = Ø120 ; Dmax = Ø120,035 and dmin = Ø120,003 ; dmax = Ø120,025.
Câu hỏi 23
Sai
Choose suitable diameters of the gear hole 1 and the counter shaft in the speed gearbox.
Select one:
a. D = Ø30-0,016 ; d = Ø30 .
c. D = Ø30 ; d = Ø30-0,013.
d. D = Ø30+0,021 ; d = Ø30 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 15/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Sai
Based on the technical requirements, the limiting deviations of the part length 165 can be defined from the dimension:
Select one:
a. 165k6. Your answer is
incorrect.
b. 165js13.
c. 165h13.
d. 165H13.
Câu hỏi 25
Sai
With a given transition fit Ø50K7/h6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. Ø50M7/h6
b. Ø50Js7/h6
d. Ø50F7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 16/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Sai
Choose suitable fit for the idler gear 8 on the intermittent shaft of the speed gear box.
Select one:
a. H7/e8 or H8/d8. Your answer is
incorrect.
b. H7/g6 or H7/f7.
c. H7/p6 or H7/r6.
d. F7/h6 or G7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 17/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Đúng
Match diameters of hole and shaft in the two following columns in order to create two fits Ø45M7/h6 and Ø45H7/k6, respectively.
Select one:
a. 1 – e ; 2 – d.
b. 1 – e ; 2 – b.
c. 10 – e ; 2 – b. Your answer is
correct.
d. 10 – e ; 2 – d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 18/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Đúng
Suggest suitable fits for the components of the below machine unit:
Select one:
a. G7/h6 for the joint between cylindrical stem 6 and flange 7 ; N7/h6 for the joint between cylindrical Your answer is
stem 6 and valse 3. correct.
b. G7/h6 for the joint between cylindrical stem 6 and flange 7 ; H7/k6 for the joint between cylindrical stem 6 and valse 3.
c. H7/g6 for the joint between cylindrical stem 6 and flange 7 ; H7/n6 for the joint between cylindrical stem 6 and valse 3.
d. N7/h6 for the joint between cylindrical stem 6 and flange 7 ; G7/h6 for the joint between cylindrical stem 6 and valse 3.
The correct answer is: G7/h6 for the joint between cylindrical stem 6 and flange 7 ; N7/h6 for the joint between cylindrical stem 6 and
valse 3.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 19/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Sai
From the fit between the pulley 7 and the shaft 2 on the assembly drawing, determine the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø27,979 , Dmax = Ø28 ; and dmin = Ø27,987 , dmax = Ø28.
The correct answer is: Dmin = Ø28 , Dmax = Ø28,021 ; and dmin = Ø28,002 , dmax = Ø28,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 20/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Sai
Select one:
a. D = Ø45-0,025 and d = Ø45 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 21/22
10/20/23, 4:08 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
b. D = Ø45-0,025 and d = Ø45±008. Your answer is
incorrect.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4923463&cmid=1147996 22/22
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Đúng
In the following fits, select one of which the interference is the greatest (if they have the same nominal size):
Select one:
a. U8/h7 Your answer is
correct
b. R7/h6
c. T7/h6
d. P7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 1/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Đúng
Select all transition fits in the basic shaft system from the following ones:
Select one:
a. Your answer is
correct.
b.
c.
d.
Câu hỏi 3
Sai
With two given fits Ø40H6/p5 and Ø40P6/h5, select the wrong sentence.
Select one:
a. The tolerances of the holes in the two fits are the same.
b. Two fits have the same Nmax and Nmin. Your answer is
incorrect.
c. the upper deviation of the shaft in the first fit is equal to lower deviation of the hole in the second fit.
d. The minimum limit of size for hole in the first fit is equal to the maximum limit of size for shaft in the second fit.
The correct answer is: the upper deviation of the shaft in the first fit is equal to lower deviation of the hole in the second fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 2/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Select one:
a. The same Smax but the different Smin
The correct answer is: The same Smin but the different Smax
Câu hỏi 5
Sai
Select a transition fit in which the probability of interference is much bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø50-0,025 ; d = Ø50 .
b. D = Ø50±0,012 ; d = Ø50±0,008.
d. D = Ø50+0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 3/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
Select one:
a. Probability of interference and probability of clearance are approximately equal.
.
Câu hỏi 7
Sai
Outer diameter d of the plain bearing and housing hole D in the machine cluster should be choosen as follows:
Select one:
a. D = Ø48 ; d = Ø48-0,016.
b. D = Ø48-0,025 ; d = Ø48+0,016.
d. D = Ø48+0,025 ; d = Ø48 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 4/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
Sort the following fits in descending order of clearance (if they have the same nominal size):
Select one:
a. Your answer is
incorrect.
b.
c.
d.
Câu hỏi 9
Đúng
A fit in the basic shaft system with Smax = 23μm, TD = 30µm, Td = 35µm. Determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø41,988 ; Dmin = Ø41,958 ; dmax = Ø42,035 ; dmin = Ø42.
c. Dmax = Ø41,988 ; Dmin = Ø41,958 ; dmax = Ø42 ; dmin = Ø41,965. Your answer is
correct.
The correct answer is: Dmax = Ø41,988 ; Dmin = Ø41,958 ; dmax = Ø42 ; dmin = Ø41,965.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 5/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Sai
Select one:
a. Ø36H7/k6 or Ø36H7/n6.
c. Ø36H7/k6 or Ø36K7/h6.
d. Ø36H7/k6 or Ø36H7/m6.
Câu hỏi 11
Sai
Choose all transition fits in the basic shaft system from the following fits.
Select one:
a. M7/h6 ; Js7/h6 ; K7/h6 ; N7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 6/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Sai
With a given transition fit Ø42M7/h6, it is necessary to select another fit in order to increase the probability of clearance:
Select one:
a. Ø42K7/h6 or Ø42Js/h6.
b. Ø42K7/h6 or Ø42F7/h6.
d. Ø42Js/h6 or Ø42H7/k6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 7/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Sai
Based on the technical requirements, the limiting deviations of the diameters Ø35 and Ø17 (view from above) can be defined from the
dimensions:
Select one:
a. Φ35js13 and Φ17H13.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 8/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Đúng
If fundamental deviation of a shaft is u and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. lower limiting deviation that is determined by ei = es - Td
Câu hỏi 15
Sai
From the fit Ø40M7/h6 on the assembly drawing, determine the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø39,975 , Dmax = Ø40 ; and dmin = Ø39,984 , dmax = Ø40.
b. Dmin = Ø40 , Dmax = Ø40,025 ; and dmin = Ø39,984 , dmax = Ø40. Your answer is
incorrect
The correct answer is: Dmin = Ø39,975 , Dmax = Ø40 ; and dmin = Ø39,984 , dmax = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 9/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Sai
Clearance fits in the basic hole system are created by fundamental deviations as follows:
Select one:
a. From p to zc.
b. From a to h.
c. From P to ZC.
d. From A to H. Your answer is
incorrect.
Câu hỏi 17
Sai
In the following fits, select one in the basic shaft system of which the interference is the smallest (if they have the same nominal size):
Select one:
a. H8/x8 Your answer is
incorrect
b. H7/p6
c. U8/h7
d. R7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 10/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Sai
With a given transition fit H7/m6, it is necessary to select another fit in order to increase the probability of interference
Select one:
a. H7/k6
c. N7/h6
d. H7/n6
Câu hỏi 19
Sai
Select one:
a. H7/r6
c. H7/f7
d. R7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 11/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Sai
Among the following fits, select a clearance fit having the biggest clearance (if they have the same nominal size)
Select one:
a. E9/h8.
c. F7/h6.
d. H8/k7.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 12/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Sai
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the F joint .
Select one:
a. Transition fit in the basic hole system. Your answer is
incorrect.
The correct answer is: Transition fit in the basic shaft system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 13/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Sai
Fit for a joint between a piston and a cylindre can be choosen as follows:
Select one:
a. H5/k6 or H6/g5.
c. H5/h4 or H6/g5.
d. H5/h4 or H6/h5
Câu hỏi 23
Sai
Determine the suitable dimensions for the piston and the cylinder bore in an hydraulic drive system:
Select one:
a. D = Φ80+0,074 ; d = Φ80-0,046.
c. D = Φ80+0,019 ; d = Φ80-0,013.
d. D = Φ80-0,013 ; d = Φ80+0,019.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 14/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Đúng
From the assembly drawing, choose proper dimensions of parts in the assembly drawing.
Select one:
a. Ø10-0,022 is dimension of the bushing hole ; Ø10 is dimension of the pin bore ; Ø10-0,015 is dimension of the piston pin.
b. Ø10 is dimension of the bushing hole ; Ø10±0,011 is dimension of the pin bore ; Ø10-0,015 is Your answer is
correct.
dimension of the piston pin.
c. Ø10±0,11 is dimension of the bushing hole ; Ø10±0,011 is dimension of the pin bore ; Ø10+0,15 is dimension of the piston pin.
d. Ø10+0,015 is dimension of the bushing hole ; Ø10 is dimension of the pin bore ; Ø10±0,011 is dimension of the piston
pin.
The correct answer is: Ø10 is dimension of the bushing hole ; Ø10±0,011 is dimension of the pin bore ; Ø10-0,015 is dimension
of the piston pin.
Câu hỏi 25
Sai
Among the following fits, select a transition fit, of which the probability of interference is much more than that of clearance
Select one:
a. T7/h6
b. H7/m6
d. H6/n5
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 15/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Sai
Interference fits in the basic hole system are created by fundamental deviations as follows:
Select one:
a. From P to ZC.
b. From a to h.
c. From A to H. Your answer is
incorrect.
d. From p to zc.
Câu hỏi 27
Đúng
Match diameters of hole and shaft in the two following columns in order to create the fit Ø45M7/h6.
Select one:
a. 2 – d.
b. 7 – e.
c. 10 – e. Your answer is
correct.
d. 9 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 16/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Sai
A nonstandardized fit may be selected (if necessary) but it must be complied with the following conditions:
Select one:
a. The fit should be either in the basic hole or basic shaft system. Additionally, tolerances of the hole and shaft should not differ
by more than two grades.
b. The fit should be in the basic hole system. Additionally, tolerances of the hole and shaft should not differ by more than one
grade.
c. The fit should be either in the basic hole or basic shaft system. Additionally, the hole tolerance grade is Your answer is
smaller than the shaft tolerance one. incorrect.
d. The fit should be in the basic shaft system. Additionally, tolerances of the hole and shaft should not differ by more than one
grade.
The correct answer is: The fit should be either in the basic hole or basic shaft system. Additionally, tolerances of the hole and shaft
should not differ by more than two grades.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 17/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Đúng
From the fit between the gear 3 and the shaft 2 (D = d = Ø28) on the assembly drawing, determine the limiting deviations of the gear hole
and shaft.
Select one:
a. ES = 0 , EI = -21µm ; and es = 6,5µm , ei = -6,5µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 18/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Sai
Choose suitable fit for the external cylinder of the plain bearings and the holes Ø40 of the below part:
Select one:
a. Ø40H7/g6.
c. Ø40H6/t5.
d. Ø40H7/n6.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922557&cmid=1147996 19/19
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / Review Chapter 2 (English) No score, only for practicing
Câu hỏi 1
Sai
Choose the proper limits of sizes for fit between the bearing cover 6 and housing 1 of a reduction gearbox.
Select one:
a. Dmin = Ø80 ; Dmax = Ø80,046 and dmin = Ø80,002 ; dmax = Ø80,032. Your answer is
incorrect.
The correct answer is: Dmin = Ø80 ; Dmax = Ø80,030 and dmin = Ø79,894 , dmax = Ø79,940.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 1/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Sort the following fits in descending order of clearance (if they have the same nominal size):
Select one:
a.
b. Your answer is
incorrect.
c.
d.
Câu hỏi 3
Sai
Collect all transition fits in the basic shaft system from the following:
Select one:
a. M7/h6 ; Js7/h6 ; K7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 2/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Select one:
a. Fundamental deviations can be positive, negative or equal to 0.
The correct answer is: Fundamental deviations can be positive, negative or equal to 0.
Câu hỏi 5
Sai
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/g6 and B = Ø40N7/h6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30. Your answer is
incorrect.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø39,967 ; D2max = Ø39,992 and d2min = Ø39,984 ; d2max = Ø40.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,80 ; d1max = Ø29,93.
Fit of dimension B: D2min = Ø39,967 ; D2max = Ø39,992 and d2min = Ø39,984 ; d2max = Ø40.
d. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø39,967 ; D2max = Ø39,992 and d2min = Ø39,984 ; d2max = Ø40.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø39,967 ; D2max = Ø39,992 and d2min = Ø39,984 ; d2max = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 3/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
With a given clearance fit in the basic hole system, in order to change Smin it is necessary to reselect:
Select one:
a. The fundamental deviation of hole.
Câu hỏi 7
Đúng
To increase the clearance of the fit G7/h6, one of the following fits will be selected:
Select one:
a. F7/h6 ; F8/h7 or H7/e7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 4/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the A joint .
Select one:
a. Clearance fit in the basic shaft system. Your answer is
incorrect.
The correct answer is: Clearance fit in the basic hole system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 5/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Sai
Select one:
a. The different Smax and Smin
The correct answer is: The same Smin but the different Smax
Câu hỏi 10
Đúng
In the following fits, select one in the basic shaft system of which the interference is the greatest (if they have the same nominal size):
Select one:
a. H8/x8
c. H7/p6
d. R7/h6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 6/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Đúng
Select grades of accuracy for piston diameter and cylindre hole in an internal combustion engine
Select one:
a. The 4th grade of accuracy for piston diameter and the 5th for cylindre hole. Your answer is
correct.
b. The 6th grade of accuracy for piston diameter and the 7th for cylindre hole.
c. The 7th grade of accuracy for piston diameter and the 6th for cylindre hole.
d. The 5th grade of accuracy for piston diameter and the 4th for cylindre hole.
The correct answer is: The 4th grade of accuracy for piston diameter and the 5th for cylindre hole.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 7/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Sai
Fit between pulley hole and shaft diameter Ø25 in the reduction gearbox can be choose as follows:
Select one:
a. Ø25K7/k6.
b. Ø25K7/h6.
d. Ø25H7/k6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 8/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Đúng
Select one:
a. D = Ø63+0,030 mm ; d = Ø63 mm
c. D =Ø24-0,033 mm ; d = Ø24-0,021 mm
d. D = Ø110+0,035 mm ; d = Ø110 mm
Câu hỏi 14
Đúng
From the fit between helical gears and shaft portions 3, 4 of an intermittent shaft in a double reduction gearbox, determine dimensions of
gear bore and shaft.
Select one:
a. D = Ø50+0,025 and d = Ø50 . Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 9/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Sai
With a given fit in the basic hole system having D = d = Ø42, Td = 26μm, Smax = 51μm, Nmax = 7μm, determine the limiting deviations of the
hole and the shaft.
Select one:
a. EI = -32µm ; ES = 0 ; ei = -51µm ; es = -25µm.
b. EI = 0 ; ES = 32µm ; ei = 0 ; es = 26µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 10/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Sai
Based on the technical requirements, the limiting deviations of the diameter Ø80 and length 135 (view from above) can be defined from
the dimensions:
Select one:
a. Ø80h13 and 135js13.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 11/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Sai
Choose a suitable fit for piston 1 and piston pin 2 of the internal combustion engine:
Select one:
a. H7/n6. Your answer is
incorrect.
b. N7/h6.
c. H7/g6.
d. G7/h6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 12/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Sai
Based on noticed working conditions of dimensions D in the below machine unit, suggest suitable limits of sizes.
Select one:
a. Dmin = Ø14 ; Dmax = Ø14,018 and dmin = Ø13,995 ; dmax = Ø14,005. Your answer is
incorrect.
The correct answer is: Dmin = Ø13,991 ; Dmax = Ø14,009 and dmin = Ø13,989 ; dmax = Ø14.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 13/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Sai
If fundamental deviation of a hole is D and the hole tolerance is TD , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by ES = TD - EI.
b. lower limiting deviation that is determined by EI = TD + ES.
c. lower limiting deviation that is determined by EI = ES - TD. Your answer is
incorrect.
The correct answer is: upper limiting deviation that is determined by ES = TD + EI.
Câu hỏi 20
Sai
With the number of holes and shafts N = 10.000 pcs in the below transition fit, compare the probability of clearance and interference of the
fit.
Select one:
a. Probability of clearance is much greater than probability of interference. Your answer is
incorrect
The correct answer is: Probability of interference is much greater than probability of clearance.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 14/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Sai
Choose proper outer diameter of plain bearing in order to assemble with hole Ø40 of the below connecting rod.
Select one:
a. Ø40 .
b. Ø40 .
d. Ø40±0,008.
Câu hỏi 22
Sai
Select the correct sentence from two fits Ø35H7/r6 and Ø120R7/h6:
Select one:
a. the lower limiting deviation of the first hole is equal to the upper limiting deviation of the second shaft.
b. the lower limiting deviations of 2 shafts are the same.
c. the upper limiting deviation of the first hole is equal to the lower limiting deviation of the second shaft. Your answer is
incorrect.
The correct answer is: the lower limiting deviation of the first hole is equal to the upper limiting deviation of the second shaft.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 15/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Sai
Select one:
a. D = Ø50+0,025; d = Ø50 . Your answer is
incorrect
b. D = Ø50+0,025 ; d = Ø50-0,016.
c. D = Ø50-0,025 ; d = Ø50 .
d. D = Ø50+0,025; d = Ø50 .
Câu hỏi 24
Sai
Choose proper outer diameter of the sleeve bearing in order to assemble with hole Ø16 of the motor stator.
Select one:
a. Ø16-0,011.
c. Ø16 .
d. Ø16 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 16/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Đúng
Sort the following fits in ascending order of clearance (if they have the same nominal size):
Select one:
a.
b.
c. Your answer is
correct.
d.
Câu hỏi 26
Sai
Select one:
a. d2 - d3 - d1 - d4
b. d4 - d3 - d1 - d2 Your answer is
incorrect.
c. d2 - d1 - d3 - d4
d. d4 - d1 - d3 - d2
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 17/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Đúng
Choose suitable pulley bore D1 (assembled with Ø25 shaft portion) and bevel gear bore D2 (assembled with Ø36 shaft portion).
Select one:
a. D1 = Ø25+0,021 and D2 = Ø36+0,025. Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 18/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Sai
According to technical requirements on the part drawing below, tolerances and limiting deviations of outer diameters Ø72 and Ø40 can be
determined as follows:
Select one:
a. Ø72-0,046 ; Ø40-0,039.
c. Ø72-0,460 ; Ø40-0,390.
d. Ø72-0,460 ; Ø40+0,390.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 19/20
10/20/23, 4:07 PM Review Chapter 2 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Sai
Select one:
a. fully below the zero line.
Câu hỏi 30
Sai
With a given fit in the basic hole system having D = d = Ø60, Td = 13μm, Smin= 10μm, Smax= 42μm, determine the limits of size
of the hole and the shaft.
Select one:
a. Dmax = Ø60,019 ; Dmin = Ø60 ; dmax = Ø59,90 ; dmin = Ø59,977 Your answer is
incorrect.
The correct answer is: Dmax = Ø60,019 ; Dmin = Ø60 ; dmax = Ø59,99 ; dmin = Ø59,977
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922422&cmid=1147996 20/20