Professional Documents
Culture Documents
Chapter 1
Chapter 1
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
With the number of holes and shafts is N = 10.000 pieces, select the diagram of transition fit in which the probability of interference is
bigger than the one of clearance when assembling at random.
Select one:
a. Sơ đồ 1
b. Sơ đồ 2 Your answer is
incorrect.
c. Sơ đồ 4
d. Sơ đồ 3
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 1/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Đúng
Select one:
a.
b. Your answer is
correct
c.
d.
Câu hỏi 3
Không trả lời
Because of hard machining holes D = Ø30 and shafts d = Ø30-0,010 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Dimensions of hole groups and shaft groups are:
Select one:
a. With holes, group I : Ø29,984 ≤ Dt ≤ Ø29,994 ; group II : Ø29,994 < Dt ≤ Ø30,004 ; group III : Ø30,004 < Dt ≤ Ø30,014.
With shafts, group I' : Ø29,990 ≤ dt ≤ Ø30 ; group II' : Ø30 < dt ≤ Ø30,010 ; group III' : Ø30,010 < dt ≤ Ø30,020.
b. With holes, group I : Ø29,984 ≤ Dt ≤ Ø29,994 ; group II : Ø29,994 < Dt ≤ Ø30,004 ; group III : Ø30,004 < Dt ≤ Ø30,014.
With shafts, group I' : Ø29,990 ≤ dt ≤ Ø30 ; group II' : Ø30 < dt ≤ Ø30,006 ; group III' : Ø30,006 < dt ≤ Ø30,020.
c. With holes, group I : Ø29,984 ≤ Dt ≤ Ø29,992 ; group II : Ø29,992 < Dt ≤ Ø30,004 ; group III : Ø30,004 < Dt ≤ Ø30,014.
With shafts, group I' : Ø29,990 ≤ dt ≤ Ø30 ; group II' : Ø30 < dt ≤ Ø30,010 ; group III' : Ø30,010 < dt ≤ Ø30,020.
d. With holes, group I : Ø29,984 ≤ Dt ≤ Ø29,994 ; group II : Ø29,994 < Dt ≤ Ø30,004 ; group III : Ø30,004 < Dt ≤ Ø30,014.
With shafts, group I' : Ø29,990 ≤ dt ≤ Ø30,001 ; group II' : Ø30,001 < dt ≤ Ø30,010 ; group III' : Ø30,010 < dt ≤ Ø30,020.
The correct answer is: With holes, group I : Ø29,984 ≤ Dt ≤ Ø29,994 ; group II : Ø29,994 < Dt ≤ Ø30,004 ; group III : Ø30,004 <
Dt ≤ Ø30,014.
With shafts, group I' : Ø29,990 ≤ dt ≤ Ø30 ; group II' : Ø30 < dt ≤ Ø30,010 ; group III' : Ø30,010 < dt ≤ Ø30,020.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 2/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Không trả lời
Choose proper outer diameter of plain bearing in order to assemble with hole Ø50 of the connecting rod below.
Select one:
a. Ø50 .
b. Ø50-0,016.
c. Ø50±0,008.
d. Ø50 .
Câu hỏi 5
Không trả lời
Select one:
a. d .
2
b. d3 .
c. d .
1
d. d4 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 3/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50 .
b. D = Ø50-0,025 ; d = Ø50 .
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50 ; d = Ø50 .
Câu hỏi 7
Không trả lời
Select one:
a. Smin = ES - ei
b. Nmin = es - EI
c. Smin = EI - es
d. Smin = ei - ES
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 4/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Không trả lời
With given holes having D = Ø120+0,035, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of clearance is greater than that of interference.
Select one:
a. d = Ø120 .
b. d = Ø120+0,022.
c. d = Ø120±0,011.
d. d = Ø120 .
Câu hỏi 9
Không trả lời
Based on the below figure, calculate limits of size of hole and shaft.
Select one:
a. Dmax = Ø36,25 ; Dmin = Ø36 and dmax = Ø35,91 ; dmin = Ø35,75.
The correct answer is: Dmax = Ø36,025 ; Dmin = Ø36 and dmax = Ø35,991 ; dmin = Ø35,975.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 5/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
Select one:
a. Figure 1: transition fit ; Figure 2: interference fit.
The correct answer is: Figure 1: interference fit ; Figure 2: transition fit.
Câu hỏi 11
Không trả lời
In order to assemble with the shaft diameter d = Ø35 in the part drawing, the limits of size of gear hole must be:
Select one:
a. Dmin = Ø35 ; Dmax = Ø35,25.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 6/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
With given shafts having d = Ø110+0,021, choose the size of the holes D so that when assembled, it will create a transition fit having Nmax =
9µm:
Select one:
a.
b.
c.
d.
Câu hỏi 13
Không trả lời
........................... is the algebric difference between the minimum limit of size and the nominal size.
Select one:
a. Lower limiting deviation
b. Tolerance
d. Limits of size
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 7/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
With a given fit of D = Ø42 and d = Ø42 , calculate the average of interference.
Select one:
a. Ntb = 69,5μm.
b. Ntb = 59,5μm.
c. Ntb = 89,5μm.
d. Ntb = 79,5μm.
Câu hỏi 15
Không trả lời
Select one:
a. 49μm
b. 19μm
c. 63μm
d. 33μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 8/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
A series of holes has Dmax = Ø42,006mm, Dmin = Ø41,983mm. Designating size of the holes on the detail drawing as follows:
Select one:
a. Ø42
b. Ø42
c. Ø42
d. Ø42
Câu hỏi 17
Không trả lời
From the fit between the plain bearing and the shaft on the assembly drawing, if shaft dimension is d = Ø40-0,016 , bearing bore should be:
Select one:
a. D = Ø40±0,019.
b. D = Ø40+0,039.
c. D = Ø40-0,039.
d. D = Ø40 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 9/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
With given shafts having d = Ø110+0,019, choose the size of the holes D so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a.
b.
c.
d.
Câu hỏi 19
Không trả lời
Because of hard machining holes D = Ø50 and shaft d = Ø50-0,016 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø50+0,048; d = Ø50 .
b. D = Ø50 ; d = Ø50 .
c. D = Ø50±0,024 ; d = Ø50 .
d. D = Ø50 ; d = Ø50-0,048.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 10/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
Suggest suitable fitted diameters for the components of the spring loaded relief valse below.
Select one:
a. Hole of the flange 7 is D = Ø12 and diameter of cylindrical stem 6 is d = Ø12-0,011.
The correct answer is: Hole of the flange 7 is D = Ø12 and diameter of cylindrical stem 6 is d = Ø12-0,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 11/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Choose a series of holes for assembling the following shafts Φ30 in order to create a clearance fit with the average clearance Stb =
28μm.
Select one:
a. D = Ø30
b. D = Ø30
c. D = Ø30+0,016
d. D = Ø30
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 12/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Choose suitable bevel gear bore D and shaft d in reduction gear box.
Select one:
a. D = Ø36-0,025 and d = Ø36 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 13/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Không trả lời
With given shafts having d = Ø50 ,choose the size of holes D so that when assembled, it will create a transition fit having Smax =
23µm.
Select one:
a. D = Ø50 .
b. D = Ø50-0,025.
c. D = Ø50 .
d. D = Ø50+0,025.
Câu hỏi 24
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create all clearance fits.
Select one:
a. 1–b ; 1–d ; 3–b ; 3–d.
The correct answer is: 1–c ; 2–a ; 2–c ; 3–c ; 4–a ; 4–c.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 14/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Choose a transition fit with the tolerance of the fit TS,N = 69μm.
Select one:
a. D = Ø65 ; d = Ø65 .
b. D = Ø65 ; d = Ø65 .
c. D = Ø65-0,037 ; d = Ø65 .
d. D = Ø65 ; d = Ø65±0,018.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 15/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 16/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
Select one:
a.
b.
c.
d.
Câu hỏi 28
Không trả lời
Select one:
a. Diagram 2
b. Diagram 3
c. Diagram 4
d. Diagram 1
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 17/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
Choose the hole diameter of the pulley for assembling with surface Ø70 of the shaft.
Select one:
a. D = Ø70-0,030.
b. D = Ø70+0,030.
c. D = Ø70+0,015.
d. D = Ø70±0,15.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 18/19
10/20/23, 3:53 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Choose the type of fit for the helical gear 30 and shaft I of the below reduction gearbox.
Select one:
a. Transition fit.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098189&cmid=1147978 19/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Choose the dimensions of gear hole and shaft in the joint below.
Select one:
a. D = Ø30 and d = Ø30-0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 1/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Select one:
a. Figure 1: transition fit ; Figure 2: interference fit.
The correct answer is: Figure 1: transition fit ; Figure 2: interference fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 2/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Sai
Suggest the suitable type of fits for the components of the below machine unit:
Select one:
a. Transition fit for the joint between cylindrical stem 6 and flange 7 ; Interference fit for the joint between cylindrical stem 6 and
valse 3.
b. Clearance fit for the joint between cylindrical stem 6 and flange 7 ; Interference fit for the joint between cylindrical stem 6 and
valse 3.
c. Transition fit for the joint between cylindrical stem 6 and flange 7 ; Clearance fit for the joint between Your answer is
cylindrical stem 6 and valse 3. incorrect.
d. Interference fit for the joint between cylindrical stem 6 and flange 7 ; Clearance fit for the joint between cylindrical stem 6 and
valse 3.
The correct answer is: Clearance fit for the joint between cylindrical stem 6 and flange 7 ; Interference fit for the joint between
cylindrical stem 6 and valse 3.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 3/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Select one:
a. D3 Your answer is
incorrect.
b. D4
c. D1
d. D2
Câu hỏi 5
Sai
Determine the suitable limits of sizes for the piston and the cylinder bore in an hydraulic drive system.
Select one:
a. Dmin = Φ50 ; Dmax = Φ50,016 and dmin = Φ49,989 ; dmax = Φ50.
b. Dmin = Φ49,992 ; Dmax = Φ50,008 and dmin = Φ49,989 ; dmax = Φ50. Your answer is
incorrect
The correct answer is: Dmin = Φ50 ; Dmax = Φ50,016 and dmin = Φ49,989 ; dmax = Φ50.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 4/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Đúng
Select one:
a. Diagram 3.
c. Diagram 2.
d. Diagram 1.
Câu hỏi 7
Đúng
With given shafts having d = Ø110-0,021, choose the size of the holes D so that when assembled, it will create a transition fit having Smax =
9µm.
Select one:
a.
b.
c. Your answer is
correct
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 5/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
With a given fit of D = Ø42 and d = Ø42 , reselect the hole so that the average of interference equals to 29,5μm.
Select one:
a. Ø42 .
c. Ø42+0,025.
d. Ø42 .
Câu hỏi 9
Sai
Select one:
a. D = Ø32+0,025 and d = Ø32 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 6/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Sai
With a given fit of D = Ø42 and d = Ø42 , reselect the hole so that the average of interference equals to 71,5μm.
Select one:
a. Ø42 .
c. Ø42+0,025.
d. Ø42 .
Câu hỏi 11
Không trả lời
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 7/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
With the number of holes and shafts N = 10.000 pcs in the below transition fit, compare the probability of clearance and interference of the
fit.
Select one:
a. Probability of clearance and probability of interference are approximately the same.
The correct answer is: Probability of clearance and probability of interference are approximately the same.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 8/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
Choose the type of fit for the impeller and the pulley that are mounted on the shaft of an industrial fan:
Select one:
a. Transition fit for two joints.
b. Transition fit for the joint between the impeller and shaft; clearance fit for the joint between the pulley and shaft.
d. Clearance fit for the joint between the impeller and shaft; transition fit for the joint between the pulley and shaft.
Câu hỏi 14
Không trả lời
Select one:
a. The replacement of worn-out or defective parts becomes very easy.
d. Machined parts reduce their service life and are difficult in assembly process.
The correct answer is: Defect rate probability could be higher than usual.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 9/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
A series of holes have Dmax = Ø49,994mm, Dmin = Ø49,983mm. Designating size of the holes on the detail drawing is as follows:
Select one:
a. Ø50
b. Ø50
c. Ø50
d. Ø50
Câu hỏi 16
Không trả lời
With given shafts having d = Ø110-0,022 , choose the size of holes D so that when assembled, it will create a transition fit having Smax =
10µm.
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 10/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Select one:
a. D = Ø45-0,025 and d = Ø45 .
Câu hỏi 18
Không trả lời
A series of shafts have Td = 11μm, dmin = Ø35,983mm. Designating size of the holes on the detail drawing as follows:
Select one:
a. Ø36
b. Ø36
c. Ø36
d. Ø36
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 11/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
A transition fit has D = d = Ø72, Td = 19μm, Nmax = 15μm, TS,N = 49μm, and bilateral hole tolerance zone. Calculate the limits of size of the
hole and the shaft.
Select one:
a. Dmax = Ø72,015 ; Dmin = Ø71,985 ; dmax = Ø72,019 ; dmin = Ø72.
The correct answer is: Dmax = Ø72,015 ; Dmin = Ø71,985 ; dmax = Ø72 ; dmin = Ø71,981.
Câu hỏi 20
Không trả lời
With given holes having D = Ø30 , choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. ø30 .
b. ø30-0,021.
c. ø30±0,01.
d. ø30+0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 12/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
With a given fit of D = Ø28 and d = Ø28-0,021, calculate Smax and Nmax
Select one:
a. Smax = 18μm ; Nmax = 36μm.
Câu hỏi 22
Không trả lời
Select one:
a. Diagram 3
b. Diagram 4
c. Diagram 2
d. Diagram 1
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 13/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Không trả lời
Select one:
a. D = Ø110+ 0,035 mm ; d = Ø110 mm
Câu hỏi 24
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the clearance fit having Smax = 67μm.
Select one:
a. 1–c.
b. 4–a.
c. 3–c.
d. 2–c.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 14/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Determine suitable limits of sizes of central part with hub 1 and toothed rim 2.
Select one:
a. Central part with hub 1: Dmin = Ø210,004 ; Dmax = Ø210,033 and toothed rim 2: dmin = Ø210 ; dmax = Ø210,46.
b. Central part with hub 1: Dmin = Ø209,954 ; Dmax = Ø210 and toothed rim 2: dmin = Ø210,004 ; dmax = Ø210,033.
c. Central part with hub 1: Dmin = Ø210,004 ; Dmax = Ø210,033 and toothed rim 2: dmin = Ø209,954 ; dmax = Ø210.
d. Central part with hub 1: Dmin = Ø210 ; Dmax = Ø210,046 and toothed rim 2: dmin = Ø210,004 ; dmax = Ø210,033.
The correct answer is: Central part with hub 1: Dmin = Ø210 ; Dmax = Ø210,046 and toothed rim 2: dmin = Ø210,004 ; dmax = Ø210,033.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 15/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Select one:
a. Interference fit
b. Clearance fit
c. Transition fit
Câu hỏi 27
Không trả lời
Select one:
a. 0,058.
b. 0,041.
c. 0,033.
d. 0,042.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 16/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Choose the dimensions of gear hole and shaft in the below fit:
Select one:
a. D = Ø40-0,025 and d = Ø40
Câu hỏi 29
Không trả lời
Select one:
a. Reduce the time and effort of the design process.
c. Reduce the number of bar sizes, cutting tools, and measuring tools for the machining process.
The correct answer is: Reduce the number of bar sizes, cutting tools, and measuring tools for the machining process.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 17/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120±0,027.
b. D = Ø120 ; d = Ø120 .
c. D = Ø120-0,047 ; d = Ø120 .
d. D = Ø120 ; d = Ø120-0,047.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098180&cmid=1147978 18/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Select one:
a. 49μm.
c. 9μm.
d. 29,5μm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 1/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
It is known that D = Ø50, TD = 25µm, ES = - 8µm. Determine if the two holes with the actual dimensions Dt1 = Ø49,9905 and
Dt2 = Ø49,9655 meet the requirements?
Select one:
a. The first one is repairable defect while the second one is satisfactory.
b. The first one is satisfactory while the second one is unrepairable defect. Your answer is
incorrect
c. The first one is satisfactory while the second one is repairable defect.
The correct answer is: The first one is satisfactory while the second one is repairable defect.
Câu hỏi 3
Sai
Select one:
a. D5 ; D4 ; D2 ; D1 ; D3.
b. D3 ; D1 ; D2 ; D4 ; D5.
d. D1 ; D4 ; D2 ; D3 ; D5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 2/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Đúng
Select one:
a. Nmax = 25μm and Smax = 0.
d. Dmin = dmin = 0.
Câu hỏi 5
Sai
With D = d = Ø60, calculate Smax , Nmax and TS,N of the fit in the below diagram.
Select one:
a. Smax = 0,048 ; Nmax = 0,041 ; TS,N = 0,089. Your answer is
incorrect
The correct answer is: Smax = 0,041 ; Nmax = 0,048 ; TS,N = 0,089.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 3/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
Because of hard machining holes D = Ø40 and shafts d = Ø40-0,016 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Dimensions of hole groups and shaft groups are:
Select one:
a. With holes, group I : Ø40,017 ≤ Dt ≤ Ø40,033 ; group II : Ø40,033 < Dt ≤ Ø40,047 ; group III : Ø40,047 < Dt ≤ Ø40,065.
With shafts, group I' : Ø39,984 ≤ dt ≤ Ø40 ; group II' : Ø40 < dt ≤ Ø40,016 ; group III' : Ø40,016 < dt ≤ Ø40,032.
b. With holes, group I : Ø40,017 ≤ Dt ≤ Ø40,033 ; group II : Ø40,033 < Dt ≤ Ø40,049 ; group III : Ø40,049 < Dt ≤ Ø40,065.
With shafts, group I' : Ø39,984 ≤ dt ≤ Ø40 ; group II' : Ø40 < dt ≤ Ø40,014 ; group III' : Ø40,014 < dt ≤ Ø40,032.
c. With holes, group I : Ø40,017 ≤ Dt ≤ Ø40,033 ; group II : Ø40,033 < Dt ≤ Ø40,049 ; group III : Ø40,049 < Dt ≤ Ø40,065.
With shafts, group I' : Ø39,984 ≤ dt ≤ Ø40 ; group II' : Ø40 < dt ≤ Ø40,016 ; group III' : Ø40,016 < dt ≤ Ø40,032.
d. With holes, group I : Ø40,017 ≤ Dt ≤ Ø40,033 ; group II : Ø40,033 < Dt ≤ Ø40,049 ; group III : Your answer is
Ø40,049 < Dt ≤ Ø40,065. incorrect.
With shafts, group I' : Ø39,984 ≤ dt ≤ Ø40,004 ; group II' : Ø40,004 < dt ≤ Ø40,016 ; group III' :
Ø40,016 < dt ≤ Ø40,032.
The correct answer is: With holes, group I : Ø40,017 ≤ Dt ≤ Ø40,033 ; group II : Ø40,033 < Dt ≤ Ø40,049 ; group III : Ø40,049 <
Dt ≤ Ø40,065.
With shafts, group I' : Ø39,984 ≤ dt ≤ Ø40 ; group II' : Ø40 < dt ≤ Ø40,016 ; group III' : Ø40,016 < dt ≤ Ø40,032.
Câu hỏi 7
Sai
With a given fit of and , reselect the shaft so that the average of clearance equals to Stb = 36,5µm.
Select one:
a. Your answer is
incorrect
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 4/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Đúng
Select one:
a. Smax = 0,023 ; Nmax = 0,033.
Câu hỏi 9
Không trả lời
With a given fit of and , reselect the shaft so that the average of clearance equals to Stb = 57µm.
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 5/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
Choose the type of fit for the toothed rim 1 and the central part with hub 2 of the below wormgear.
Select one:
a. Transition fit.
b. Clearance fit.
d. Interference fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 6/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
In order to create transition fit (in which tolerance of the fit TS,N = 34μm) between driven pulley and shaft portion of Ø25 diameter, pulley
bore must be:
Select one:
a. D = Ø25+0,021.
b. D = Ø25±0,021.
c. D = Ø25+0,21.
d. D = Ø25-0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 7/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Select one:
a.
b.
c.
d.
Câu hỏi 13
Không trả lời
Select one:
a. 9μm.
b. 20,5μm.
c. 29,5μm.
d. 41μm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 8/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
Select one:
a. Figure 1: transition fit ; Figure 2: interference fit
The correct answer is: Figure 1: transition fit ; Figure 2: interference fit
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 9/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
From the assembly drawing, determine dimensions of pin 2 and hole of roller pulley wheel 4 in the roller pulley wheel unit.
Select one:
a. Ø12+0,27 is hole diameter of roller pulley wheel 4 and Ø12-0,18 is diameter of pin 2.
b. Ø12+0,027 is hole diameter of roller pulley wheel 4 and Ø12±0,009 is diameter of pin 2.
c. Ø12+0,027 is hole diameter of roller pulley wheel 4 and Ø12-0,018 is diameter of pin 2.
d. Ø12-0,027 is hole diameter of roller pulley wheel 4 and Ø12-0,018 is diameter of pin 2.
The correct answer is: Ø12+0,027 is hole diameter of roller pulley wheel 4 and Ø12-0,018 is diameter of pin 2.
Câu hỏi 16
Không trả lời
Choose the suitable type of fits for the joints of the below machine unit:
Select one:
a. Interference fit for the joint between item 1 and 2 ; Clearance fit for the joint between item 3 and 2.
b. Clearance fit for the joint between item 1 and 2 ; Transition fit for the joint between item 3 and 2.
c. Transition fit for the joint between item 1 and 2 ; Clearance fit for the joint between item 3 and 2.
d. Clearance fit for the joint between item 1 and 2 as well as the joint between item 3 and 2.
The correct answer is: Clearance fit for the joint between item 1 and 2 ; Transition fit for the joint between item 3 and 2.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 10/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
A transition fit has D = d = Ø40, TD = 25μm, Smax = 16μm, ei = 9μm, TS,N = 41μm. Calculate the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø40,025 ; Dmin = Ø40 ; dmax = Ø40,007 ; dmin = Ø39,991.
The correct answer is: Dmax = Ø40,025 ; Dmin = Ø40 ; dmax = Ø40,025 ; dmin = Ø40,009.
Câu hỏi 18
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120 .
b. D = Ø120 ; d = Ø120±0,027.
c. D = Ø120-0,047 ; d = Ø120 .
d. D = Ø120 ; d = Ø120 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 11/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
Suggest suitable fitted diameters D and d of flange 7 and stem 6 in the spring loaded relief valse below.
Select one:
a. D = Ø10 ; d = Ø10-0,015.
b. D = Ø10 ; d = Ø10+0,015.
c. D = Ø10 ; d = Ø12-0,015.
d. D = Ø10 ; d = Ø10-0,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 12/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
Choose a series of holes for assembling the following shafts Φ30 in order to create a clearance fit with the average clearance Stb =
31,5μm.
Select one:
a. D = Ø30
b. D = Ø30
c. D = Ø30
d. D = Ø30+0,016
Câu hỏi 21
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the transition fit having Nmax = 8μm.
Select one:
a. 2–d.
b. 3–a.
c. 4–b.
d. 2–b.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 13/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
With a given fit of D = Ø42 and d = Ø42 , reselect the shaft so that the average of interference equals to 47,5μm.
Select one:
a. Ø42 .
b. Ø42 .
c. Ø42+0,016.
d. Ø42 .
Câu hỏi 23
Không trả lời
Select one:
a. D = Ø50-0,025 ; d = Ø50 .
b. D = Ø50 ; d = Ø50-0,025.
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50 ; d = Ø50-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 14/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
A fit has the following data TD = 38μm, Nmax = 46μm, shaft lower deviation equals 0, bilateral tolerance of hole. Calculate the hole and
shaft limiting deviations.
Select one:
a. ES = 19μm, EI = -19μm, es = 46μm, ei = 0
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 15/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Choose the proper dimensions of gear hole 30 and shaft 25 in the below reduction gearbox.
Select one:
a. D = Ø40+0,025 and d = Ø40 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 16/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Choose the limits of sizes d of pin 1 and body hole D of "a Cardan universal coupling".
Select one:
a. dmin = Ø17,989 , dmax = Ø18 ; Dmin = Ø17,977 , Dmax = Ø17,995.
The correct answer is: dmin = Ø17,989 , dmax = Ø18 ; Dmin = Ø17,977 , Dmax = Ø17,995.
Câu hỏi 27
Không trả lời
With D = d = Ø45, calculate Nmax , Nmin and TN of the fit in the below diagram.
Select one:
a. Nmax = 0,73 ; Nmin = 0,16 ; TN = 0,57.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 17/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Calculate the limiting deviations and tolerance for the shaft having d = Ø30 mm
Select one:
a. es = - 0,017mm; ei = +0,004mm; T = 0,023mm.
d
Câu hỏi 29
Không trả lời
Because of hard machining holes D = Ø40+0,016 and shafts d = Ø40 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Dimensions of hole groups and shaft groups are:
Select one:
a. With holes, group I : Ø40 ≤ Dt ≤ Ø40,010 ; group II : Ø40,010 < Dt ≤ Ø40,020 ; group III : Ø40,020 < Dt ≤ Ø40,030.
With shafts, group I' : Ø40,017 ≤ dt ≤ Ø40,033 ; group II' : Ø40,033 < dt ≤ Ø40,049 ; group III' : Ø40,049 < dt ≤ Ø40,065.
b. With holes, group I : Ø40 ≤ Dt ≤ Ø40,016 ; group II : Ø40,016 < Dt ≤ Ø40,032 ; group III : Ø40,032 < Dt ≤ Ø40,048.
With shafts, group I' : Ø40,017 ≤ dt ≤ Ø40,033 ; group II' : Ø40,033 < dt ≤ Ø40,049 ; group III' : Ø40,049 < dt ≤ Ø40,065.
c. With holes, group I : Ø40 ≤ Dt ≤ Ø40,016 ; group II : Ø40,016 < Dt ≤ Ø40,030 ; group III : Ø40,030 < Dt ≤ Ø40,048.
With shafts, group I' : Ø40,017 ≤ dt ≤ Ø40,033 ; group II' : Ø40,033 < dt ≤ Ø40,049 ; group III' : Ø40,049 < dt ≤ Ø40,065.
d. With holes, group I : Ø40 ≤ Dt ≤ Ø40,016 ; group II : Ø40,016 < Dt ≤ Ø40,032 ; group III : Ø40,032 < Dt ≤ Ø40,048.
With shafts, group I' : Ø40,017 ≤ dt ≤ Ø40,033 ; group II' : Ø40,033 < dt ≤ Ø40,047 ; group III' : Ø40,047 < dt ≤ Ø40,065.
The correct answer is: With holes, group I : Ø40 ≤ Dt ≤ Ø40,016 ; group II : Ø40,016 < Dt ≤ Ø40,032 ; group III : Ø40,032 <
Dt ≤ Ø40,048.
With shafts, group I' : Ø40,017 ≤ dt ≤ Ø40,033 ; group II' : Ø40,033 < dt ≤ Ø40,049 ; group III' : Ø40,049 < dt ≤ Ø40,065.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 18/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Choose the outer diameter of plain bearing assembled with hole Ø16+0,018 of "a rocker arm" in an internal combustion
engine.
Select one:
a. Ø16±0,0055.
b. Ø16-0,011.
c. Ø16 .
d. Ø16 .
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098162&cmid=1147978 19/19
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Determine the limits of size and tolerance of the width of slot B = 100 in the part drawing
Select one:
a. Bmax = 99,976 ; Bmin = 99,941 ; TB = 0,083.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 1/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Outer diameter d of the plain bearing and housing hole D in the machine cluster should be choosen as follows:
Select one:
a. D = Ø50+0,025 ; d = Ø50 .
c. D = Ø50-0,025 ; d = Ø50+0,016.
d. D = Ø50+0,025 ; d = Ø50-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 2/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Đúng
Outer diameter d of the plain bearing and housing hole D in the machine cluster should be choosen as follows:
Select one:
a. D = Ø48+0,025 ; d = Ø48 .
b. D = Ø48+0,025 ; d = Ø48-0,016.
d. D = Ø48 ; d = Ø48-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 3/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Determine suitable dimensions of central part with hub 1 and toothed rim 2.
Select one:
a. Central part with hub 1: Ø210+0,046 and toothed rim 2: Ø210 .
b. Central part with hub 1: Ø210 and toothed rim 2: Ø210-0,046. Your answer is
incorrect.
The correct answer is: Central part with hub 1: Ø210+0,046 and toothed rim 2: Ø210 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 4/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Không trả lời
Tolerances of diameters Ø100 and Ø125 of the shaft are not shown on the part drawing, so they can be specified as follows:
Select one:
a. Ø100-0,63 ; Ø125-0,54.
b. Ø100-0,54 ; Ø125 .
c. Ø100-0,54 ; Ø125-0,63.
d. Ø100-0,054 ; Ø125+0,063.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 5/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Không trả lời
With a given fit of D = Ø42 and d = Ø42 , reselect the shaft so that the average of interference equals to 54,5μm.
Select one:
a. Ø42+0,016.
b. Ø42 .
c. Ø42 .
d. Ø42 .
Câu hỏi 7
Không trả lời
With a given fit having D = Ø45 and d = Ø45-0,025 , determine the average clearance of fit.
Select one:
a. 47μm
b. 43μm
c. 57μm
d. 44,5μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 6/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Không trả lời
Select one:
a. ES = -0,008 ; EI = -0,033 ; TD = 0,041 and es = 0 ; ei = -0,016 ; Td = 0,016.
The correct answer is: ES = -0,008 ; EI = -0,033 ; TD = 0,025 and es = 0 ; ei = -0,016 ; Td = 0,016.
Câu hỏi 9
Không trả lời
Select one:
a. The tolerances of mating parts are allowed to increase in order to meet machining requirements.
c. Machined parts are measured and sorted into groups by dimension prior to assembly process.
The correct answer is: The tolerances of mating parts are allowed to increase in order to meet machining requirements.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 7/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
From the fit between helical gears and shaft portions 3, 4 of an intermittent shaft in a double reduction gearbox, determine dimensions of
gear bore and shaft.
Select one:
a. D = Ø30+0,021 ; d = Ø30 .
b. D = Ø30+0,021 ; d = Ø30-0,013.
c. D = Ø30-0,021 ; d = Ø30±0065.
d. D = Ø30-0,021 ; d = Ø30 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 8/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the clearance fit having the average clearance Stb =
25μm.
Select one:
a. 3–c.
b. 4–a.
c. 2–c.
d. 1–c.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 9/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
The limits of size of the slot b = 10±0,011 on the detail drawing are:
Select one:
a. bmin= 9,089 ; bmax= 10,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 10/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
Choose proper diameters of the fit between sleeve bearing bore D and motor shaft d in a DC fan.
Select one:
a. D = Ø20+0,21 ; d = Ø20 .
b. D = Ø20+0,021 ; d = Ø20 .
c. D = Ø20+0,021 ; d = Ø20 .
d. D = Ø20±0,010 ; d = Ø20 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 11/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
With nominal size D = d = Ø30, maximum and minimum diameters of holes and shafts in the below diagrams of tolerance disposition are:
Figure 1 Figure 2
Select one:
a. Fig. 1: Dmax = Ø29,964 ; Dmin = Ø29,997 ; dmax = Ø30 ; dmin = Ø29,979.
The correct answer is: Fig. 1: Dmax = Ø29,997 ; Dmin = Ø29,964 ; dmax = Ø30 ; dmin = Ø29,979.
Fig. 2: Dmax = Ø30,005 ; Dmin = Ø29,978 ; dmax = Ø30,016 ; dmin = Ø29,997.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 12/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Determine the suitable dimensions for the piston and the cylinder bore in an hydraulic drive system:
Select one:
a. D = Φ50-0,011 ; d = Φ50±0,008.
b. D = Φ50+0,016 ; d = Φ50-0,011.
c. D = Φ50±0,008 ; d = Φ50-0,011.
d. D = Φ50-0,011 ; d = Φ50+0,016.
Câu hỏi 16
Không trả lời
Select one:
a. 54μm.
b. 18μm.
c. 33μm.
d. 51μm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 13/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Select one:
a. mating parts in the joints that do not require the high accuracy.
The correct answer is: mating parts in the joints that require the high accuracy.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 14/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Choose proper dimension d of transmission shafts in order to assemble with holes D = Ø16 in the part drawing.
Select one:
a. D = Ø16-0,018 ; d = Ø16 .
b. D = Ø16 ; d = Ø16 .
c. D = Ø16+0,018 ; d = Ø16 .
d. D = Ø16 ; d = Ø16-0,018.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 15/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
A given fit has D = Ø30+0,021mm and d = Ø30±0,0065mm. Choose the correct sentence.
Select one:
a. Hole tolerance is bilateral tolerance and shaft tolerance is unilateral tolerance.
The correct answer is: Shaft tolerance is bilateral tolerance and hole tolerance is unilateral tolerance.
Câu hỏi 20
Không trả lời
Limiting deviations of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. ES = -0,024 ; EI = -0,057 ; es = 0 ; ei = -0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 16/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Select one:
a. D =Ø24-0,033 mm ; d = Ø24-0,021 mm
b. D = Ø63+0,030 mm ; d = Ø63 mm
c. D = Ø75 mm ; d = Ø75-0,019 mm
d. D = Ø110+0,035 mm ; d = Ø110 mm
Câu hỏi 22
Không trả lời
With D = d = Ø45, calculate limits of sizes of the mating parts in the below diagram:
Select one:
a. Dmax = Ø44,962 ; Dmin = Ø44,27 and dmax = Ø45 ; dmin = Ø44,78.
The correct answer is: Dmax = Ø44,962 ; Dmin = Ø44,927 and dmax = Ø45 ; dmin = Ø44,978.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 17/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Không trả lời
The algebraic difference between the maximum limit of size and the corresponding nominal one is:
Select one:
a. Upper limiting deviation
b. Limiting deviation
d. Tolerance
Câu hỏi 24
Không trả lời
Choose the dimensions of gear hole and shaft in the below fit.
Select one:
a. D = Ø28+0,021 ; d = Ø28
b. D = Ø28 ; d = Ø28+0,021
c. D = Ø28 ; d = Ø28-0,021
d. D = Ø28-0,021 ; d = Ø28
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 18/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Select one:
a. d .
2
b. d .
1
c. d4 .
d. d .
3
Câu hỏi 26
Không trả lời
From the assembly drawing, determine the limits of size of piston hole and piston pin.
Select one:
a. Hole piston: Dmin = Ø10 , Dmax = Ø10,015 ; Piston pin: dmin = Ø9,989 , dmax = Ø10,011.
b. Hole piston: Dmin = Ø9,89 , Dmax = Ø10,11 ; Piston pin: dmin = Ø9,85 , dmax = Ø10.
c. Hole piston: Dmin = Ø9,989 , Dmax = Ø10,011 ; Piston pin: dmin = Ø9,985 , dmax = Ø10.
d. Hole piston: Dmin = Ø10 , Dmax = Ø10,022 ; Piston pin: dmin = Ø9,985 , dmax = Ø10.
The correct answer is: Hole piston: Dmin = Ø9,989 , Dmax = Ø10,011 ; Piston pin: dmin = Ø9,985 , dmax = Ø10.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 19/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
With given shafts having d = Ø110-0,022 , choose the size of holes D so that when assembled, it will create a clearance fit with the average
clearance Stb = 33µm.
Select one:
a.
b.
c.
d.
Câu hỏi 28
Không trả lời
With given holes having D = Ø24+0,021, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. d = Ø24±0,0065.
b. d = Ø24 .
c. d = Ø24+0,013.
d. d = Ø24 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 20/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
With a given fit of and , reselect the shaft so that the average of clearance equals to Stb = 89µm.
Select one:
a.
b.
c.
d.
Câu hỏi 30
Không trả lời
Determine if the two housings with the actual width of slot bt1 = 99,086 and bt2 = 99,967 meet the requirements?
Select one:
a. Both of them meet the requirement.
d. The first one is repairable defective, meanwhile the second meets the requirement.
The correct answer is: The first one is repairable defective, meanwhile the second meets the requirement.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 21/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098153&cmid=1147978 22/22
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
With a given fit having d = Ø50 and D = Ø50 mm, calculate Smax , Smin , Nmax , Nmin of the fit.
Select one:
a. Smax = 11µm ; Smin = 16µm ; Nmin = 0 ; Nmax = 44µm.
b. Smax = 11µm ; Smin = Nmin = 0 ; Nmax = 44µm.
c. Smax = 44µm ; Smin = Nmin = 0 ; Nmax = 11µm. Your answer is
incorrect.
The correct answer is: Smax = 11µm ; Smin = Nmin = 0 ; Nmax = 44µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 1/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Đúng
Determine the limits of size and tolerance for center distance L between hole Ø16 and internal spline of the below part
Select one:
a. Lmin = 76,07 ; Lmax = 77,003 ; T = 0,06.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 2/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Không trả lời
Choose the suitable limits of size for the spindle d and the hole D of the tailstock in an engine lathe.
Select one:
a. Dmin = Φ39,993 ; Dmax = Φ40 and dmin = Φ40 ; dmax = Φ40,011.
The correct answer is: Dmin = Φ40 ; Dmax = Φ40,011 and dmin = Φ39,993 ; dmax = Φ40.
Câu hỏi 4
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50-0,016.
b. D = Ø50-0,025 ; d = Ø50 .
c. D = Ø50 ; d = Ø50-0,025.
d. D = Ø50+0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 3/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50-0,025.
b. D = Ø50 ; d = Ø50 .
c. D = Ø50 ; d = Ø50 .
d. D = Ø50 ; d = Ø50 .
Câu hỏi 6
Không trả lời
With given shafts having d = Ø50 , choose the size of the holes D so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. ø50±0,012.
b. ø50 .
c. ø50-0,025.
d. ø50+0,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 4/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
Which one is the clearance fit with the average clearance Stb = 38,5μm?
Select one:
a.
b.
c.
d.
Câu hỏi 8
Không trả lời
Select one:
a. Interference fit with the average interference Ntb = 29,5μm.
The correct answer is: Interference fit with the average interference Ntb = 26,5μm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 5/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Không trả lời
With a given fit having D = Ø54 mm, d = Ø54+0,028 mm, calculate the tolerance of the fit TS,N
Select one:
a. 36μm.
b. 42μm.
c. 51μm.
d. 23μm.
Câu hỏi 10
Không trả lời
Limiting deviations of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. ES = -0,036 ; EI = -0,003 ; es = 0 ; ei = -0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 6/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
With a given fit having D = d = Ø28, TD = 21μm, Nmin = 7μm, es = 0, Nmax= 41μm, determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø27,98 ; Dmin = Ø27,059 ; dmax = Ø28 ; dmin = Ø27,087
The correct answer is: Dmax = Ø27,98 ; Dmin = Ø27,959 ; dmax = Ø28 ; dmin = Ø27,987
Câu hỏi 12
Không trả lời
In a clearance fit, the maximum clearance Smax and the minimum clearance Smin are calculated by the following formulas:
Select one:
a. Smax = ES - ei and Smin = EI - es.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 7/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
Choose the shaft diameter in order to assemble with the bore of the rolling bearing Ø65-0,012
Select one:
a. Ø65
b. Ø65±0,015
c. Ø65+0,03
d. Ø65-0,016
Câu hỏi 14
Không trả lời
Select one:
a. Stb = 150μm
b. Stb = 200μm
c. Stb = 80μm
d. Stb = 180μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 8/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Select one:
a. Nominal (basic) size
c. Limits of size
d. Tolerance
Câu hỏi 16
Không trả lời
Choose proper fits between helical gears and shaft portions 3, 4 as well as fits between sleeves and shaft portions 2, 5 of an intermittent
shaft in a double reduction gearbox.
Select one:
a. Clearance fit for shaft portions 3, 4; and transition fit for shaft portions 2, 5.
b. Interference fit for shaft portions 3, 4; and clearance fit for shaft portions 2, 5.
c. Transition fit for shaft portions 3, 4; and interference fit for shaft portions 2, 5.
d. Transition fit for shaft portions 3, 4; and clearance fit for shaft portions 2, 5.
The correct answer is: Transition fit for shaft portions 3, 4; and clearance fit for shaft portions 2, 5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 9/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Choose the proper diameter d of pin 1 assembled with body hole D of "a Cardan universal coupling".
Select one:
a. d = Ø16 ; D = Ø16 .
b. d = Ø16-0,011 ; D = Ø16 .
c. d = Ø16 ; D = Ø16-0,018.
d. d = Ø16±0,0055 ; D = Ø16 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 10/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
With the fits in the figures 1 and 2 below, calculate hole and shaft tolerances.
Figure 1
Figure 2
Select one:
a. Figure 1: TD = 25µm ; Td = 16µm. Figure 2: TD = 19µm ; Td = 30µm.
The correct answer is: Figure 1: TD = 25µm ; Td = 16µm. Figure 2: TD = 30µm ; Td = 19µm.
Câu hỏi 19
Không trả lời
Select one:
a. 41μm
b. 25μm
c. 16μm
d. 9μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 11/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
With a given fit of D = Ø42 and d = Ø42 , reselect the shaft so that the average of interference equals to 62,5μm.
Select one:
a. Ø42 .
b. Ø42 .
c. Ø42 .
d. Ø42+0,016.
Câu hỏi 21
Không trả lời
Because of hard machining holes D = Ø30 and shafts d = Ø30-0,010 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø30+0,030; d = Ø30 .
b. D = Ø30 ; d = Ø30-0,030.
c. D = Ø30 ; ; d = Ø30 .
d. D = Ø30 ; D = Ø30 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 12/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Suggest a suitable type of fit for the diameter Ø60 between the tool holder 1 and the base plate 2 of the square tool post below.
Select one:
a. Interference fit or transition fit.
b. Clearance fit.
c. Transition fit.
d. Interference fit.
Câu hỏi 23
Không trả lời
With a given fit having D = d = Ø48, TD = 25μm, Nmax = 33μm, es = 0, Smax = 8μm, determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø47,992 ; Dmin = Ø47,967 ; dmax = Ø48 ; dmin = Ø47,984.
The correct answer is: Dmax = Ø47,992 ; Dmin = Ø47,967 ; dmax = Ø48 ; dmin = Ø47,984.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 13/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Tolerances of diameters d1 = Ø30 and d2 = Ø50 of the shaft are not shown on the part drawing, so they can be specified as follows:
Select one:
a. d1min = Ø29,61 ; d1max = Ø30 and d2min = Ø49,67 ; d2max = Ø50.
The correct answer is: d1min = Ø29,67 ; d1max = Ø30 and d2min = Ø49,61 ; d2max = Ø50.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 14/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
With the number of holes and shafts is N = 10.000 pieces, select the diagram in which the probability of clearance is greater than the one
of interference when assembling at random.
Select one:
a. Diagram 2
b. Diagram 4
c. Diagram 3
d. Diagram 1
Câu hỏi 26
Không trả lời
Select a transition fit in which the probability of interference is a little greater than the one of clearance when assembling at random.
Select one:
a. D = Ø50+0,025 ; d = Ø50±0,008.
b. D = Ø50+0,025 ; d = Ø50 .
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50-0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 15/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
From the fit between gear and shaft on the assembly drawing, choose the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø39,975 , Dmax = Ø40 ; and dmin = Ø40 , dmax = Ø40,016.
The correct answer is: Dmin = Ø39,975 , Dmax = Ø40 ; and dmin = Ø39,984 , dmax = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 16/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Select one:
a. D = Ø50 .
b. D = Ø50-0,016.
c. D = Ø50+0,016.
d. D = Ø50±0,008.
Câu hỏi 29
Không trả lời
With a given fit having D = Ø50-0,025 and d = Ø50 , determine the average interference of fit.
Select one:
a. 43μm
b. 22,5μm
c. 40μm
d. 23,5μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 17/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
With the number of holes and shafts is N = 10.000 pieces, select the diagram in which the probability of clearance is bigger than the one of
interference when assembling at random.
Select one:
a. Diagram 2
b. Diagram 1
c. Diagram 3
d. Diagram 4
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 18/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
With a given fit of D = Ø42 and d = Ø42 , reselect the shaft so that the average of interference equals to 45,5μm.
Select one:
a. Ø42 . Your answer is
incorrect
b. Ø42+0,016.
c. Ø42 .
d. Ø42 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 1/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Select a transition fit in which the probability of interference is much greater than the one of clearance when assembling at random.
Select one:
a. D = Ø50+0,025 ; d = Ø50 .
b. D = Ø50±0,012 ; d = Ø50±0,008.
d. D = Ø50+0,025 ; d = Ø50 .
Câu hỏi 3
Sai
Select one:
a.
b. Your answer is
incorrect
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 2/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Đúng
Calculate the limits of size dmax and dmin in the above detail drawing:
Select one:
a. dmax = Ø29,060 and dmin = Ø29,073
Câu hỏi 5
Đúng
A series of shafts have Td = 23μm, dmin = Ø35,983mm. Designating size of the shafts on the detail drawing is as follows:
Select one:
a. Ø36
b. Ø36
d. Ø36
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 3/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Sai
Match diameters of hole and shaft in the two following columns in order to create all interference fits.
Select one:
a. 1–b ; 1–d ; 3–b ; 3–d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 4/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Sai
From the assembly drawing of the below machine unit, determine dimensions of valse hole 3 and cylindrical stem 6.
Select one:
a. Ø12+0,018 is hole diameter of valse 3 and Ø12 is diameter of cylindrical stem 6.
c. Ø12+0,018 is hole diameter of valse 3 and Ø12±0,0055 is diameter of cylindrical stem 6. Your answer is
incorrect.
The correct answer is: Ø12+0,018 is hole diameter of valse 3 and Ø12 is diameter of cylindrical stem 6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 5/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Sai
Select the type of fit for the joint between the V pulley 7 and the shaft 2:
Select one:
a. Clearance fit.
c. Transition fit.
d. Interference fit.
Câu hỏi 9
Không trả lời
With given holes having D = Ø24+0,021, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of clearance is greater than that of interference.
Select one:
a. d = Ø24 .
b. d = Ø24±0,0065.
c. d = Ø24 .
d. d = Ø24+0,013.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 6/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
From the chosen fit between the outer diameter of the plain bearings and the holes of Ø16 in the part drawing below, determine the hole
diameter D of the part holes and outer diameter d of the plain bearings.
Select one:
a. D = Ø16±0,009 ; d = Ø16 .
b. D = Ø16+0,018 ; d = Ø16-0,011.
c. D = Ø16+0,018 ; d = Ø16 .
d. D = Ø16±0,009 ; d = Ø16±0,11.
Câu hỏi 11
Không trả lời
Select one:
a. machining spare parts in common machines
The correct answer is: machining and assembly process in a factory’s production line.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 7/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Choose proper limits of size for outer diameter d of the plain bearing in order to assemble with the housing bore D = Ø50+0,025
Select one:
a. dmin = Ø49,984 ; dmax = Ø50.
Câu hỏi 13
Không trả lời
With a given fit having D = Ø45 and d = Ø45 mm, calculate Smax , Smin , Nmax , Nmin of the fit.
Select one:
a. Smax = 13µm ; Smin = 0 ; Nmin = 16µm ; Nmax = 50µm.
b. Smax = 50µm ; Smin = Nmin = 0 ; Nmax = 13µm.
c. Smax = 13µm ; Smin = Nmin = 0 ; Nmax = 50µm.
d. Smax = 50µm ; Smin = 17µm ; Nmin = 9µm ; Nmax = 23µm.
The correct answer is: Smax = 13µm ; Smin = Nmin = 0 ; Nmax = 50µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 8/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
Select one:
a. An interference fit with TN = 0,057.
Câu hỏi 15
Không trả lời
With nominal size D = d = Ø30, maximum and minimum diameters of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. Dmax = Ø30,016 ; Dmin = Ø29,989 ; dmax = Ø29,98 ; dmin = Ø29,79.
The correct answer is: Dmax = Ø30,016 ; Dmin = Ø29,989 ; dmax = Ø29,998 ; dmin = Ø29,979.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 9/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120±0,027.
b. D = Ø120-0,047 ; d = Ø120 .
c. D = Ø120 ; d = Ø120 .
d. D = Ø120 ; d = Ø120-0,047.
Câu hỏi 17
Không trả lời
Select one:
a. 41μm.
b. 49μm.
c. 45μm.
d. 51μm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 10/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Select one:
a. Smax = 16μm and Nmax = 15μm
Câu hỏi 19
Không trả lời
Choose a series of holes for assembling the following shafts Φ30 in order to create a clearance fit with the average clearance Stb =
23,5μm.
Select one:
a. D = Ø30+0,016
b. D = Ø30
c. D = Ø30
d. D = Ø30
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 11/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
With a given fit having D = Ø120-0,035 , d = Ø120 , calculate tolerance of the fit.
Select one:
a. 49μm
b. 25μm
c. 51μm
d. 65μm
Câu hỏi 21
Không trả lời
From the fit between helical gears and shaft portions 3, 4 of an intermittent shaft in a double reduction gearbox, determine dimensions of
gear bore and shaft.
Select one:
a. D = Ø50-0,025 and d = Ø50±008.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 12/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
With a given fit having D = Ø45 and d = Ø45 mm, calculate Smax , Smin , Nmax , Nmin of the fit.
Select one:
a. Smax = 14µm ; Smin = Nmin = 0 ; Nmax = 42µm.
b. Smax = 42µm ; Smin = Nmin = 0 ; Nmax = 14µm.
c. Smax = 14µm ; Smin = 17µm ; Nmin = 6µm ; Nmax = 42µm.
d. Smax = 14µm ; Smin = 0 ; Nmin = 17µm ; Nmax = 42µm.
The correct answer is: Smax = 14µm ; Smin = Nmin = 0 ; Nmax = 42µm.
Câu hỏi 23
Không trả lời
Choose the proper limits of size for hole D of the plain pulley and shaft diameter d (the left end of the shaft) in the assembly drawing.
Select one:
a. Dmin = Ø40 ; Dmax = Ø40,039 and dmin = Ø40,002 ; dmax = Ø40,018.
The correct answer is: Dmin = Ø39,941 ; Dmax = Ø39,964 and dmin = Ø39,984 ; dmax = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 13/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Choose the correct answer for the width of slot B = 100 in the part drawing
Select one:
a. ES = -0,024 ; EI = -0,059 ; TB = 0,035.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 14/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Choose the type of fit for the rolling bearing 26 and shaft I of the below reduction gearbox.
Select one:
a. Interference fit with very small interference amount.
b. Transition fit.
The correct answer is: Interference fit with very small interference amount.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 15/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Suggest the suitable dimensions for assembling the idle gear on the shaft.
Select one:
a. D = Ø55+0,030 and d = Ø55±0,0095.
Câu hỏi 27
Không trả lời
With the number of holes and shafts N = 10.000 pcs in the below transition fit, compare the probability of clearance and interference of the
fit.
Select one:
a. Probability of interference is much bigger than probability of clearance.
The correct answer is: Probability of interference is much bigger than probability of clearance.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 16/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
With nominal size D = d = Ø30, maximum and minimum diameters of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. Dmax = Ø29,964 ; Dmin = Ø29,943 ; dmax = Ø30 ; dmin = Ø29,967.
The correct answer is: Dmax = Ø29,976 ; Dmin = Ø29,943 ; dmax = Ø30 ; dmin = Ø29,979.
Câu hỏi 29
Không trả lời
With a given fit having and , determine the average clearance of fit.
Select one:
a. 64μm
b. 40μm
c. 64,5μm
d. 46μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 17/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Dimension of a hole on the part drawing is D = Ø60±0,0065mm. Calculate the limits of size and tolerance.
Select one:
a. Dmax = Ø60,0065mm ; Dmin = Ø59,9935mm ; TD = 0,013mm
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098138&cmid=1147978 18/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Select one:
a. Diagram 3.
b. Diagram 2.
d. Diagram 1.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 1/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Select one:
a.
b.
c. Your answer is
incorrect
d.
Câu hỏi 3
Sai
With given holes having D = Ø26+0,021, choose the size of the shafts so that when assembled, it will create a clearance fit having
Smax = 37µm.
Select one:
a. d = Ø26+0,016
b. d = Ø26-0,037
d. d = Ø26-0,016
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 2/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Limiting deviations of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. ES = -0,008 ; EI = -0,033 ; es = 0 ; ei = -0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 3/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Đúng
Select one:
a. D = Ø120±0,011.
c. D = Ø120-0,022.
d. D = Ø120 .
Câu hỏi 6
Không trả lời
With a given fit having D = Ø50-0,025 and d = Ø50 , determine the tolerance of fit TN.
Select one:
a. 23,5μm
b. 43μm
c. 41μm
d. 40μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 4/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
Because of hard machining holes D = Ø40 and shafts d = Ø40-0,016 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø40 ; d = Ø40 .
b. D = Ø40+0,048; d = Ø40 .
c. D = Ø40 ; d = Ø40 .
d. D = Ø40 ; d = Ø40 .
Câu hỏi 8
Không trả lời
With given holes having D = Ø50 , choose the size of shafts d so that when assembled, it will create a clearance fit having Smin =
12µm.
Select one:
a. d = Ø50 .
b. d = Ø50+0,025.
c. d = Ø50 .
d. d = Ø50-0,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 5/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Không trả lời
Based on noticed working conditions of the below machine unit, suggest the suitable type of fits for the components.
Select one:
a. Clearance fit for E ; Transition fit for C.
The correct answer is: Clearance fit for E ; Transition fit for C.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 6/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
Select the type of fit for the joint between the sleeve 4 and the shaft 2:
Select one:
a. Clearance fit.
c. Interference fit.
d. Transition fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 7/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
Based on noticed working conditions of the below machine unit, suggest the suitable type of fits for the components.
Select one:
a. Clearance fit for A and C; Transition fit for B.
The correct answer is: Clearance fit for A ; Transition fit for B and C.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 8/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Choose proper outer diameter of the sleeve bearing in order to assemble with hole Ø16+0,018 of the motor stator.
Select one:
a. Ø16-0,011.
b. Ø16 .
c. Ø16 .
d. Ø16±0,0055.
Câu hỏi 13
Không trả lời
Select one:
a. Upper limiting deviation is always bigger than lower limiting deviation.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 9/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
Choose a series of holes for assembling the following shafts Φ30 in order to create the clearance fit with Smax = 34μm :
Select one:
a. D = Ø30+0,016
b. D = Ø30-0,016
c. D = Ø30±0,021
d. D = Ø30+0,021
Câu hỏi 15
Không trả lời
With the following data, choose the appropriate diagram of disposition of tolerance zones for fit:
Select one:
a. Diagram 3.
b. Diagram 2.
c. Diagram 1.
d. Diagram 4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 10/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
From the assembly drawing of the below machine unit, determine dimensions of valse hole 3 and cylindrical stem 6.
Select one:
a. Ø10 is hole diameter of valse 3 and Ø10-0,015 is diameter of cylindrical stem.
The correct answer is: Ø10 is hole diameter of valse 3 and Ø10-0,015 is diameter of cylindrical stem.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 11/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create all transition fits.
Select one:
a. 1–a ; 2–b ; 2–d ; 3–a ; 4–b ; 4–d.
The correct answer is: 1–a ; 2–b ; 2–d ; 3–a ; 4–b ; 4–d.
Câu hỏi 18
Không trả lời
It is known that D = Ø34, TD = 34µm, EI = - 16,5µm. Determine if the two holes with the actual dimensions Dt1 = Ø33,9825 and
Dt2 = Ø34,0165 meet the requirements?
Select one:
a. Both of them are satisfactory
c. The first one is satisfactory and the second one does not meet the requirement
d. The second one is satisfactory and the first one does not meet the requirement
The correct answer is: The second one is satisfactory and the first one does not meet the requirement
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 12/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
From the fit between sleeves and shaft portions 2, 5 of an intermittent shaft in a double reduction gearbox, determine dimensions of
sleeve bore and shaft.
Select one:
a. D = Ø45+0,039 and d = Ø45 .
Câu hỏi 20
Không trả lời
Select one:
a. Nmax = Dmax - dmin
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 13/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
In the reduction gearbox below, fits for the fixed joints between gears and shafts can be chosen as follows:
Select one:
a. Transition fit.
b. Clearance fit.
c. Interference fit.
Câu hỏi 22
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120 .
b. D = Ø120 ; d = Ø120 .
c. D = Ø120 ; d = Ø120±0,027.
d. D = Ø120-0,047 ; d = Ø120 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 14/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50 .
b. D = Ø50-0,025 ; d = Ø50 .
c. D = Ø50 ; d = Ø50 .
d. D = Ø50+0,025 ; d = Ø50 .
Câu hỏi 24
Không trả lời
From the fit between the plain bearing and shaft on the assembly drawing, determine the limits of size of the bearing hole and shaft.
Select one:
a. Dmin = Ø39,961 , Dmax = Ø40 ; and dmin = Ø40 , dmax = Ø40,016.
The correct answer is: Dmin = Ø40,025 , Dmax = Ø40,064 ; and dmin = Ø39,984 , dmax = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 15/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
An interference fit has D = d = Ø46, TD = 25μm, Nmax = 50μm, TN = 41μm, and bilateral shaft tolerance zone. Calculate the limiting
deviations of the hole and the shaft.
Select one:
a. EI = -50µm , ES = -25µm ; ei = -8µm , es = 8µm.
Câu hỏi 26
Không trả lời
Choose the correct answer for the slot width B = 100 in the part drawing
Select one:
a. ES = -0,024 ; EI = -0,059.
b. es = -0,024 ; EI = -0,059.
c. ES = -0,024 ; ei = -0,059.
d. es = -0,024 ; ei = -0,059.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 16/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
A series of holes have the following data D = Ø24mm, ES = 4,5µm, EI = -4,5µm. Calculate their limits of size
Select one:
a. Dmax = Ø24,0045mm ; Dmin = Ø23,955mm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 17/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Choose proper bearing bore in order to assemble with the shaft portion Ø90 on the following part drawing:
Select one:
a. Ø90-0,015.
b. Ø90±0,030.
c. Ø90 .
d. Ø90+0,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 18/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
From the assembly drawing, determine dimensions of piston hole and piston pin:
Select one:
a. Ø10±0,011 is dimension of the hole in the piston and Ø10-0,015 is dimension of the piston pin.
b. Ø10+0,022 is dimension of the hole in the piston and Ø10-0,015 is dimension of the piston pin.
c. Ø10±0,11 is dimension of the hole in the piston and Ø10+0,15 is dimension of the piston pin.
d. Ø10+0,015 is dimension of the hole in the piston and Ø10±0,011 is dimension of the piston pin.
The correct answer is: Ø10±0,011 is dimension of the hole in the piston and Ø10-0,015 is dimension of the piston pin.
Câu hỏi 30
Không trả lời
Which one is the interference fit with the average interference Ntb = 46μm?
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 19/20
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098129&cmid=1147978 20/20
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Đúng
From the assembly drawing, determine the limits of size of body hole 1, pulley hole 4 and pin 2 in the roller pulley wheel unit.
Select one:
a. Hole of the body 1: Dmin = Ø12,016 , Dmax = Ø12,043 ; Hole of the pulley wheel 4: Dmin = Ø11,987 , Dmax = Ø12,013 ;
Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
b. Hole of the body 1: Dmin = Ø11,087 , Dmax = Ø12,13 ; Hole of the pulley wheel 4: Dmin = Ø12,16 , Dmax = Ø12,43 ; Diameter
of the pin 2: dmin = Ø11,982 , dmax = Ø12.
c. Hole of the body 1: Dmin = Ø11,987 , Dmax = Ø12,013 ; Hole of the pulley wheel 4: Dmin = Ø12,016 Your answer is
, Dmax = Ø12,043 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12. correct.
d. Hole of the body 1: Dmin = Ø11,987 , Dmax = Ø12,013 ; Hole of the pulley wheel 4: Dmin = Ø11,982 , Dmax = Ø12 ; Diameter
of the pin 2: dmin = Ø12,016 , dmax = Ø12,043.
The correct answer is: Hole of the body 1: Dmin = Ø11,987 , Dmax = Ø12,013 ; Hole of the pulley wheel 4: Dmin = Ø12,016
, Dmax = Ø12,043 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 1/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Because of hard machining holes D = Ø40+0,016 and shafts d = Ø40 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø40+0,048 ; d = Ø40 . Your answer is
incorrect.
b. D = Ø40+0,040; d = Ø40 .
c. D = Ø40+0,048 ; d = Ø40 .
d. D = Ø40 ; d = Ø40 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 2/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Sai
Choose the suitable keywidth in order to assemble with the slot b = 10 in the part drawing that creates transition fit with Smax = 22μm and
Nmax = 11μm.
Select one:
a. b = 10-0,11.
c. b = 10-0,011.
d. b = 10±0,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 3/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Không trả lời
Select one:
a. Diagram 1.
b. Diagram 2.
c. Diagram 3.
d. Diagram 4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 4/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Không trả lời
From the fit between the housing hole and outer diameter of plain bearing on the assembly drawing, if housing bore is D = Ø48+0,025, outer
diameter d of plain bearing should be:
Select one:
a. d = Ø48 .
b. d = Ø48 .
c. d = Ø48±0,008.
d. d = Ø48-0,016.
Câu hỏi 6
Không trả lời
With a given fit having calculate limits of sizes of the hole and shaft
Select one:
a. Dmax = Ø35,06 ; Dmin = Ø34,085 and dmax = Ø35,01 ; dmin = Ø34,990.
The correct answer is: Dmax = Ø35,006 ; Dmin = Ø34,985 and dmax = Ø35,010 ; dmin = Ø34,990.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 5/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
Determine suitable diameters for driven helical gear bore D and shaft diameter d in one-stage gear reducer.
Select one:
a. D = Ø50 and d = Ø50-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 6/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Không trả lời
Choose proper outer diameter d of the plain bearing in order to assemble with the housing bore D = Ø50+0,025
Select one:
a. Ø50 .
b. Ø50+0,16.
c. Ø50 .
d. Ø50-0,016.
Câu hỏi 9
Không trả lời
Select one:
a. D3 ; D1 ; D2 ; D5 ; D4.
b. D1 ; D4 ; D2 ; D3 ; D5.
c. D3 ; D1 ; D2 ; D4 ; D5.
d. D5 ; D4 ; D2 ; D1 ; D3.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 7/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
Choose the type of fit for the cone gear 28 and shaft I of the below reduction gearbox.
Select one:
a. Transition fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 8/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
Select one:
a. Smin = 0,017
b. Smin = 0
c. Smin = 0,019
d. Smin = 0,006
Câu hỏi 12
Không trả lời
Figure 1
Figure 2
Select one:
a. Figure 1: Transition fit ; Figure 2: Clearance fit.
The correct answer is: Figure 1: Interference fit ; Figure 2: Clearance fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 9/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
It is known that D = Ø45, TD = 18µm, EI = - 25µm. Determine if the two holes with the actual dimensions Dt1 = Ø44,9955 and
Dt2 = Ø44,9755 meet the requirements?
Select one:
a. The first one is satisfactory while the second one is unrepairable defect.
c. The second one is satisfactory while the first one is unrepairable defect.
d. The second one is satisfactory while the first one is repairable defect.
The correct answer is: The second one is satisfactory while the first one is unrepairable defect.
Câu hỏi 14
Không trả lời
Choose the limits of size of gear hole and shaft in the below fit.
Select one:
a. Dmin = Ø28,002 , Dmax = Ø28,015 ; and dmin = Ø28 , dmax = Ø28,021.
The correct answer is: Dmin = Ø28 , Dmax = Ø28,021 ; and dmin = Ø28,002 , dmax = Ø28,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 10/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 11/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
Choose the suitable shaft d in order to assemble with hole of the worn gear D = ø80H7 = ø80+0,030.
Select one:
a. d = Ø80 .
b. d = Ø80 .
c. d = Ø80 .
d. d = Ø80+0,19.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 12/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Determine the limits of size and tolerance for center distance L = 107±0,03 of the below part
Select one:
a. Lmin = 106,097 ; Lmax = 107,030 ; T = 0,03.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 13/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Choose the suitable hole of gear in order to assemble with the shaft diameter d = Ø35 in the part drawing.
Select one:
a. D = Ø35+0,25.
b. D = Ø35-0,025.
c. D = Ø35±0,0125.
d. D = Ø35+0,025.
Câu hỏi 19
Không trả lời
With a given fit having D = Ø45-0,025 mm, d = Ø45-0,016mm, choose the correct answer
Select one:
a. Smax= 25μm and Nmax = 16μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 14/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
With a given fit having D = Ø30+0,025mm, d = Ø30 mm, calculate the tolerance of the fit TS,N
Select one:
a. T
S,N = 0,023mm.
b. TS,N = 0,042mm.
c. T
S,N = 0,048mm.
d. T
S,N = 0,006m.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 15/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Determine suitable dimensions of hole Ø30 of the below part and a shaft in a fixed joint, of which the end face is clamped with the part by
3 bolts M8
Select one:
a. D = Ø30+0,021 ; d = Ø30 .
b. D = Ø30 ; d = Ø30+0,021.
c. D = Ø30-0,021 ; d = Ø30+0,016.
d. D = Ø30±0,009 ; d = Ø30-0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 16/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Choose a series of holes for assembling the following shafts Φ30 in order to create the clearance fit with Smax = 106μm and Smin = 40μm.
Select one:
a. D = Ø30±0,013.
b. D = Ø30-0,033.
c. D = Ø30±0,033.
d. D = Ø30+0,033.
Câu hỏi 23
Không trả lời
Select one:
a. D2
b. D3
c. D1
d. D4
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 17/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Select one:
a. The algebraic difference between the maximum and the minimum limit of size.
b. The algebraic difference between the maximum limit of size and the corresponding nominal one.
c. The algebraic difference between the nominal size and the limits of size.
d. The algebraic difference between the nominal size and the corresponding actual one.
The correct answer is: The algebraic difference between the maximum limit of size and the corresponding nominal one.
Câu hỏi 25
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120±0,027.
b. D = Ø120-0,047 ; d = Ø120 .
c. D = Ø120 ; d = Ø120 .
d. D = Ø120 ; d = Ø120 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 18/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Select one:
a. Nmin = 0,016
b. Nmin = 0,033
c. Nmin = 0,014
d. Nmin = 0
Câu hỏi 27
Không trả lời
Choose the limits of size of plain bearing hole D and of piston pin d.
Select one:
a. Dmin = Ø17,989 , Dmax = Ø18 ; dmin = Ø18,006 ; dmax = Ø18,024.
The correct answer is: Dmin = Ø18,006 , Dmax = Ø18,024 ; dmin = Ø17,989 , dmax = Ø18.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 19/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
From the assembly drawing, determine the limits of size of the parts in the assembly unit.
Select one:
a. Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10 , Dmax = Ø10,015 ; Piston pin: dmin = Ø9,989 ,
dmax = Ø10,011.
b. Pin bore: Dmin = Ø10,013 , Dmax = Ø10,035 ; Bushing hole: Dmin = Ø9,989 , Dmax = Ø10,011 ; Piston pin: dmin = Ø9,985 ,
dmax = Ø10.
c. Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10,013 , Dmax = Ø10,035 ; Piston pin: dmin = Ø9,985 ,
dmax = Ø10.
d. Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10 , Dmax = Ø10,022 ; Piston pin: dmin = Ø9,985 ,
dmax = Ø10.
The correct answer is: Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10,013 , Dmax = Ø10,035 ; Piston pin:
dmin = Ø9,985 , dmax = Ø10.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 20/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
Select one:
a. D = Ø35+0,025 and d = Ø35-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 21/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Choose the outer diameter d of plain bearing assembled with hole D of "a rocker arm" in an internal combustion engine.
Select one:
a. d = Ø15 ; D = Ø15-0,018.
b. d = Ø15 ; D = Ø15+0,018.
c. d = Ø15±0,0055 ; D = Ø15+0,018.
d. d = Ø15-0,011 ; D = Ø15+0,018.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 22/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Select one:
a. Dmax = Ø45 ; Dmin = Ø44,984 and dmax = Ø44,992 ; dmin = Ø44,967.
c. Dmax = Ø44,092 ; Dmin = Ø44,067 and dmax = Ø45 ; dmin = Ø44,084. Your answer is
incorrect
The correct answer is: Dmax = Ø44,992 ; Dmin = Ø44,967 and dmax = Ø45 ; dmin = Ø44,984.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 1/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Choose suitable diameters of the gear 4 and the counter shaft in the speed gearbox.
Select one:
a. D = Ø42-0,016 and d = Ø42 .
Câu hỏi 3
Sai
It is known that d = Ø18, Td = 28µm, ei = - 34µm. Determine if the two shafts with the actual dimensions dt1 = Ø17.9955 and dt2 = Ø17.975
meet the requirements?
Select one:
a. The second one is satisfactory and the first one does not meet the requirement
d. The first one is satisfactory and the second one does not meet the requirement
The correct answer is: The second one is satisfactory and the first one does not meet the requirement
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 2/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Sai
Determine the limits of size of the pulley hole 7 and shaft 2 on the assembly drawing.
Select one:
a. Dmin = Ø35 , Dmax = Ø35,025 ; and dmin = Ø34,984 , dmax = Ø35. Your answer is
incorrect.
The correct answer is: Dmin = Ø35 , Dmax = Ø35,025 ; and dmin = Ø35,002 , dmax = Ø35,018.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 3/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Không trả lời
From the fit between the V-belt pulley and the shaft on the assembly drawing, determine the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø25 , Dmax = Ø25,021 ; and dmin = Ø25,002 , dmax = Ø25,015.
The correct answer is: Dmin = Ø25 , Dmax = Ø25,021 ; and dmin = Ø25,002 , dmax = Ø25,015.
Câu hỏi 6
Không trả lời
With a given fit of D = Ø42 and d = Ø42 , reselect the hole so that the average of interference equals to 20,5μm.
Select one:
a. Ø42+0,025.
b. Ø42 .
c. Ø42 .
d. Ø42 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 4/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
Select one:
a. Requiring the mating parts that must be manufactured in different places.
Câu hỏi 8
Không trả lời
With the fits in the figures 1 and 2 below, choose the correct answer.
Figure 1
Figure 2
Select one:
a. Figure 1: the average clearance Stb = 26,5µm ; Figure 2: the average interference Ntb = 29,5µm.
b. Figure 1: the average clearance Stb = 29,5µm ; Figure 2: the average interference Ntb = 26,5µm.
c. Figure 1: the average clearance Stb = 31,5µm ; Figure 2: the average interference Ntb = 26,5µm.
d. Figure 1: the average clearance Stb = 29,5µm ; Figure 2: the average interference Ntb = 24,5µm.
The correct answer is: Figure 1: the average clearance Stb = 29,5µm ; Figure 2: the average interference Ntb = 26,5µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 5/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Không trả lời
With a given fit having D = Ø34 mm, d = Ø34+0,019mm, calculate Smax and Nmax.
Select one:
a. Smax = 0,023 and Nmax = 0,036
Câu hỏi 10
Không trả lời
Figure 1
Figure 2
Select one:
a. Figure 1: Clearance fit ; Figure 2: Interference fit.
The correct answer is: Figure 1: Clearance fit ; Figure 2: Interference fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 6/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
Select one:
a. es = -0,040 ; ei = -0,073 ; Td = 0,033.
Câu hỏi 12
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50-0,025.
b. D = Ø50 ; d = Ø50-0,016.
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50-0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 7/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
From the assembly drawing, determine dimensions of pin 2 and two holes of body 1 in the roller pulley wheel unit.
Select one:
a. Ø12-0,027 is hole diameter of body 1 and Ø12-0,018 is diameter of pin 2.
The correct answer is: Ø12-0,027 is hole diameter of body 1 and Ø12-0,018 is diameter of pin 2.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 8/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
Select the type of fit for the joint between the gear 3 and the shaft 2:
Select one:
a. Clearance fit.
b. Transition fit.
d. Interference fit.
Câu hỏi 15
Không trả lời
With nominal size D = d = Ø30, maximum and minimum diameters of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. Dmax = Ø29,997 ; Dmin = Ø29,964 ; dmax = Ø30 ; dmin = Ø29,979.
The correct answer is: Dmax = Ø29,997 ; Dmin = Ø29,964 ; dmax = Ø30 ; dmin = Ø29,979.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 9/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
From the assembly drawing, determine the limits of size of pulley hole 4 and pin 2 in the roller pulley wheel unit.
Select one:
a. Hole of the pulley wheel 4: Dmin = Ø12,16 , Dmax = Ø12,43 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
b. Hole of the pulley wheel 4: Dmin = Ø11,982 , Dmax = Ø12 ; Diameter of the pin 2: dmin = Ø12,016 , dmax = Ø12,043.
c. Hole of the pulley wheel 4: Dmin = Ø12,016 , Dmax = Ø12,043 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
d. Hole of the pulley wheel 4: Dmin = Ø11,987 , Dmax = Ø12,013 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
The correct answer is: Hole of the pulley wheel 4: Dmin = Ø12,016 , Dmax = Ø12,043 ; Diameter of the pin 2: dmin = Ø11,982 ,
dmax = Ø12.
Câu hỏi 17
Không trả lời
The algebraic difference between the minimum limit of size and the corresponding nominal one is:
Select one:
a. Lower limiting deviation
c. Limiting deviation
d. Tolerance
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 10/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Choose the type of fit for two cylindrical centers which are mounted accurately on the holes Ø40 of the below housing as well as they can
be adjusted axially and be clamped by bolts M10:
Select one:
a. Clearance fit with Smin = 0.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 11/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 19
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120-0,047.
b. D = Ø120 ; d = Ø120 .
c. D = Ø120-0,047 ; d = Ø120 .
d. D = Ø120 ; d = Ø120±0,027.
Câu hỏi 20
Không trả lời
From the assembly drawing, choose proper dimensions of parts in the assembly drawing.
Select one:
a. Ø10 is dimension of the bushing hole ; Ø10±0,011 is dimension of the pin bore ; Ø10-0,015 is dimension of the piston
pin.
b. Ø10-0,022 is dimension of the bushing hole ; Ø10 is dimension of the pin bore ; Ø10-0,015 is dimension of the piston pin.
c. Ø10+0,015 is dimension of the bushing hole ; Ø10 is dimension of the pin bore ; Ø10±0,011 is dimension of the piston
pin.
d. Ø10±0,11 is dimension of the bushing hole ; Ø10±0,011 is dimension of the pin bore ; Ø10+0,15 is dimension of the piston pin.
The correct answer is: Ø10 is dimension of the bushing hole ; Ø10±0,011 is dimension of the pin bore ; Ø10-0,015 is dimension
of the piston pin.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 12/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
From the fit between helical gears and shaft portions 3, 4 of an intermittent shaft in a double reduction gearbox, determine limits of sizes
of gear bore and shaft.
Select one:
a. Dmin = Ø50 , Dmax = Ø50,025 ; and dmin = Ø49,984 , dmax = Ø50.
The correct answer is: Dmin = Ø50 , Dmax = Ø50,025 ; and dmin = Ø50,002 , dmax = Ø50,018.
Câu hỏi 22
Không trả lời
Select one:
a. 0,36 mm.
b. 0,036 mm.
c. 0,046 mm.
d. 0,051 mm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 13/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 23
Không trả lời
Select one:
a. Interference fit with Nmax = 23μm and Nmin = 7μm.
The correct answer is: Interference fit with Nmax = 41μm and Nmin = 7μm.
Câu hỏi 24
Không trả lời
Select one:
a. D3
b. D2
c. D1
d. D4
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 14/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
With untolerated cylindrical surfaces Ø30, Ø36 and Ø60 of the part, their tolerances are not shown on the part drawing, so they can be
specified as follows:
Select one:
a. Ø30-0,033 ; Ø36-0,039 ; Ø60-0,046.
Câu hỏi 26
Không trả lời
Select one:
a. Nmin = es - EI
b. Nmin = ES - ei
c. Nmin = ei - ES
d. Nmin = EI - es
Câu hỏi 27
Không trả lời
With the number of holes and shafts N = 10.000 pcs in the below transition fit, determine the probability of clearance and interference of
the fit
Select one:
a. Probability of clearance is about 80% and Probability of interference is about 20%.
The correct answer is: Probability of clearance is about 20% and Probability of interference is about 80%.
Câu hỏi 28
Không trả lời
With a fit having D = Ø42±0,012 and d = Ø42-0,016, c alculate the tolerance of the fit.
Select one:
a. 33μm
b. 40μm
c. 28μm
d. 24μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 16/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
Calculate hole tolerance and shaft tolerance in the following diagram of tolerance dispositions:
Figure 1 Figure 2
Select one:
a. Figure 1: TD = 0,016mm , Td = 0,025mm ; Figure: TD = 0,025mm , Td = 0,016mm.
The correct answer is: Figure 1: TD = 0,025mm , Td = 0,016mm ; Figure 2: TD = 0,025mm , Td = 0,016mm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 17/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Choose the suitable dimensions for the spindle d and the hole D of the tailstock in an engine lathe
Select one:
a. D = Ø40+0,025 and d = Ø40-0,016.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096401&cmid=1147978 18/18
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Select a transition fit in which the probability of interference is much bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø80-0,030 ; d = Ø80 .
c. D = Ø80+0,030 ; d = Ø80 .
d. D = Ø80+0,030 ; d = Ø80 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 1/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Không trả lời
Select one:
a. D4
b. D2
c. D3
d. D1
Câu hỏi 3
Không trả lời
With given holes having D = Ø110+0,035, choose the size of shafts d so that when assembled, it will create a transition fit having Smax =
32µm:
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 2/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Không trả lời
For nominal size Ø30, determine if the two shafts with the actual dimensions dt1 = Ø29,073 and dt2 = Ø29,067 meet the requirements.
Select one:
a. Both of them are unrepairable defectives.
c. The first one is unrepairable defective, meanwhile the second meets the requirement.
Câu hỏi 5
Không trả lời
With given holes having D = Ø120+0,035, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. d = Ø120±0,011.
b. d = Ø120 .
c. d = Ø120+0,022.
d. d = Ø120 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 3/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Không trả lời
Choose the type of fit for piston and cylinder of the internal combustion engine.
Select one:
a. Clearance fit.
b. Interference fit.
d. Transition fit.
Câu hỏi 7
Không trả lời
A clearance fit has D = d = Ø76, TD = 30μm, Smax = 60,5μm, TS = 49μm, and bilateral shaft tolerance zone. Calculate the limiting deviations
of the hole and the shaft.
Select one:
a. EI = 30µm , ES = 60µm ; ei = -9,5µm , es = 9,5µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 4/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Không trả lời
With given shafts having d = Ø28+0,016, choose the size of the holes so that when assembled, it will create a transition fit having Nmax =
27µm.
Select one:
a. D = Ø28±0,027
b. D = Ø28-0,027
c. D = Ø28±0,011
d. D = Ø28+0,027
Câu hỏi 9
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the clearance fit having the average clearance Stb =
59μm.
Select one:
a. 3–c.
b. 4–c.
c. 2–c.
d. 4–a.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 5/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
If a series of holes has D = Ø50±0,012 , select the shafts in order to create a transition fit having Nmax = 0,033 and Smax = 0,012:
Select one:
a. d = Ø50±0,013
b. d = Ø50+0,021
c. d = Ø50+0,016
d. d = Ø50-0,033
Câu hỏi 11
Không trả lời
Select one:
a. 63μm
b. 19,5μm
c. 49μm
d. 38,5μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 6/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Because of hard machining holes D = Ø50 and shafts d = Ø50-0,016 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Dimensions of hole groups and shaft groups are:
Select one:
a. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,040 ; group III : Ø50,040 < Dt ≤ Ø50,057.
With shafts, group I' : Ø50,984 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
b. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,041 ; group III : Ø50,041 < Dt ≤ Ø50,057.
With shafts, group I' : Ø49,984 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
c. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,040 ; group III : Ø50,040 < Dt ≤ Ø50,057.
With shafts, group I' : Ø49,084 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
d. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,041 ; group III : Ø50,041 < Dt ≤ Ø50,057.
With shafts, group I' : Ø49,984 ≤ dt ≤ Ø50,004 ; group II' : Ø50,004 < dt ≤ Ø50,018 ; group III' : Ø50,018 < dt ≤ Ø50,032.
The correct answer is: With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,041 ; group III : Ø50,041 <
Dt ≤ Ø50,057.
With shafts, group I' : Ø49,984 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
Câu hỏi 13
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the interference fit having the average interference Ntb =
47,5μm.
Select one:
a. 1–d.
b. 1–b.
c. 3–d.
d. 3–b.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 7/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
From the fit between sleeves and shaft portions 2, 5 of an intermittent shaft in a double reduction gearbox, determine limits of sizes of
sleeve bore and shaft.
Select one:
a. Dmin = Ø45 , Dmax = Ø45,039 ; and dmin = Ø44,975 , dmax = Ø45.
The correct answer is: Dmin = Ø45 , Dmax = Ø45,039 ; and dmin = Ø44,950 , dmax = Ø44,975.
Câu hỏi 15
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the interference fit having Nmax = 51μm.
Select one:
a. 1–d.
b. 3–b.
c. 1–b.
d. 3–d.
Câu hỏi 16
Không trả lời
With nominal size D = d = Ø30, maximum and minimum diameters of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. Dmax = Ø30,016 ; Dmin = Ø29,997 ; dmax = Ø30,005 ; dmin = Ø29,978.
The correct answer is: Dmax = Ø30,005 ; Dmin = Ø29,978 ; dmax = Ø30,016 ; dmin = Ø29,997.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 9/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Choose proper dimensions between pulley hole D and shaft d in the below industrial fan.
Select one:
a. D = Ø42+0,025 ; d = Ø42 .
b. D = Ø42+0,025 ; d = Ø42 .
c. D = Ø42±0,012 ; d = Ø42-0,016.
d. D = Ø42+0,025 ; d = Ø42-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 10/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Suggest limits of size for sleeve bore 8 and shaft 2 on the assembly drawing.
Select one:
a. Dmin = Ø40 , Dmax = Ø40,039 ; and dmin = Ø39,975 , dmax = Ø40.
The correct answer is: Dmin = Ø40 , Dmax = Ø40,039 ; and dmin = Ø39,950 , dmax = Ø39,975.
Câu hỏi 19
Không trả lời
A fit has the following data Td = 32μm, Smax = 56μm, EI = 0, bilateral tolerance of shaft. Calculate the hole and shaft limiting deviations.
Select one:
a. ES = 40μm, EI = 0, es = 20μm, ei = -12μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 11/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the clearance fit having the average clearance Stb =
42μm.
Select one:
a. 2–c.
b. 4–a.
c. 3–c.
d. 1–c.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 12/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Determine the limits of size and tolerance of the width of slot B = 10 in the part drawing.
Select one:
a. Bmin = 9,989 ; Bmax = 10,011 ; TB = 0,022.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 13/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
In an interference fit, the maximum interference Nmax and the minimum interference Nmin are calculated by the following formulas:
Select one:
a. Nmax = es - EI ; Nmin = ei - ES.
Câu hỏi 23
Không trả lời
From the fit between rolling bearings and shaft portions 1, 6 of an intermittent shaft in a double reduction gearbox, determine dimensions
of the bearing bore D and the shaft d.
Select one:
a. D = Ø40-0,012 ; d = Ø40±008.
b. D = Ø40+0,012 ; d = Ø40 .
c. D = Ø40-0,012 ; d = Ø40 .
d. D = Ø40+0,012 ; d = Ø40-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 14/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
With the following data, choose the appropriate diagram of disposition of tolerance zones for fit:
Select one:
a. Diagram 4.
b. Diagram 1.
c. Diagram 2.
d. Diagram 3.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 15/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Tolerances of diameters Ø77 and Ø105 of the connecting rod are not shown on the part drawing, so they can be specified as
follows:
Select one:
a. Ø77-0,046 and Ø105 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 16/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Choose proper dimensions for the outer diameter d of the sleeve bearing and stator bore D in a DC fan motor.
Select one:
a. d = Ø16 ; D = Ø16-0,018.
b. d = Ø16 ; D = Ø16+0,018.
c. d = Ø16 ; D = Ø16+0,018.
d. d = Ø16±0,0055 ; D = Ø16 .
Câu hỏi 27
Không trả lời
With a fit having , calculate the hole tolerance and shaft tolerance of the fit
Select one:
a. TD = 3μm ; Td = 19μm
b. TD = 30μm ; Td = 47μm
c. TD = 30μm ; Td = 19μm
d. TD = 33μm ; Td = 19μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 17/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Select a transition fit in which the probability of interference is a little bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø80+0,030 ; d = Ø80 .
b. D = Ø80-0,030 ; d = Ø80 .
c. D = Ø80+0,030 ; d = Ø80 .
d. D = Ø80+0,030 ; d = Ø80±0,0095.
Câu hỏi 29
Không trả lời
In a transition fit, the maximum interference Nmax is calculated by the following formula:
Select one:
a. Nmax = EI - es.
b. Nmax = es - EI.
c. Nmax = ei - ES.
d. Nmax = ES - ei.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 18/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Select one:
a. D = Ø25-0,021 and d = Ø25 .
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 19/19