Professional Documents
Culture Documents
MiniProject - Xem lại lần làm thử
MiniProject - Xem lại lần làm thử
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 1/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
Câu hỏi 1
Hoàn thành
Fig. shows a gear train with number of teeth on the gears given as Z1= 70, Z2= 28, Z’2= 80, Z3=20, Z4=60. All the gears are standard spur
gears and the same module m = 3. The gear no. 1 rotates at 1440 rpm.
CHÚ Ý:
NHẬP DẤU "CHẤM" GIỮA PHẦN NGUYÊN VÀ THẬP PHÂN, KHÔNG NHẬP DẤU PHẨY GIỮA PHẦN NGUYÊN VÀ PHẦN THẬP PHÂN. VÍ
DỤ: NHẬP 3.14 THAY VÌ 3,14
TỈ SỐ TRUYỀN VÀ TỐC ĐỘ QUAY CỦA TRỤC CÓ THỂ CÓ GIÁ TRỊ ÂM(GIÁ TRỊ ÂM NGHĨA LÀ 2 TRỤC QUAY NGƯỢC CHIỀU VÀ GIÁ TRỊ
DƯƠNG NGHĨA LÀ 2 TRỤC QUAY CÙNG CHIỀU)
QUESTION:
Transmission ratio of the planetary gear train (from gear Z2' to the arm C): u2c = 0.857
The rotational speed nc and direction of arm C (a negative number indicates that the gear no. 1 and the arm C rotate in the opposite
direction and a positive number indicates that the gear no. 1 and the arm C rotate in the same direction).
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 2/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
nc = 50 (rpm)
Câu hỏi 2
Hoàn thành
A chain drive using the ANSI chain number 100, p = 31.75 mm transmits 5 kW of power. The driven shaft on driven machine runs at 200 rpm
and velocity ratio is 2. The number of teeth on the driving sprocket is Z1 = 21.
d2 = 424.86 (mm)
3- Find the number of links and length of chain if approximately center distance is choosen as atr = 42p
Noted: The chosen links must be an even number and it's also greater than the calculated links
Ft = 1123.81 (N)
5- Given the factor kx =1.05, find the force acting on the shaft?
Fr = 1180.00 (N)
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 3/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
Câu hỏi 3
Hoàn thành
CHÚ Ý:
NHẬP DẤU "CHẤM" GIỮA PHẦN NGUYÊN VÀ THẬP PHÂN, KHÔNG NHẬP DẤU PHẨY GIỮA PHẦN NGUYÊN VÀ PHẦN THẬP PHÂN. VÍ
DỤ: NHẬP 3.14 THAY VÌ 3,14
Question:
1- Determine the contact angle on the small pulley and the large pulley?
α1 171.614 (degree)
α2 188.38 (degree)
2-The power and the speed of in the driving shaft are given as P1 = 5.5 kW and n1 = 1420 rpm. The intial tension in the belt is Fo = 600 N.
Neglecting the tension due to the centrifugal force. Determine the tension in the tight side and tension in the slack side.
F1 = 831.2865 (N)
F2 = 368.7135 (N)
3- Determine the minimum of the coefficient of friction between the belt and the pulley not to occur slippage
f ≥ 0.041
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 4/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
Câu hỏi 4
Hoàn thành
A transmission shaft of the gear reducer is shown in Fig. The helical gear, Z1 , has a pitch circle diamter, d1 = 200 mm, forces acting on teeth:
Ft1 =600 (N); Fr1 =226 (N) and Fa1 =161 (N). The spur gear, Z2 has a pitch circle diameter, d2 = 125 mm, forces acting on teeth: Ft2 =960
(N); Fr2 =350 (N). Given the other datas as: L1 =110 mm; L2 = 140 mm ; L3 = 120 mm and the allowable stress of the shaft, [σ]=55 MPa.
>> Notes: + The direction of reaction forces at the bearing location are assumed as in Fig.
+ The answer of the reaction forces will be a negative number if the direction of reaction forces is opposite to the direction
shown in Fig.
CHÚ Ý:
NHẬP DẤU "CHẤM" GIỮA PHẦN NGUYÊN VÀ THẬP PHÂN, KHÔNG NHẬP DẤU PHẨY GIỮA PHẦN NGUYÊN VÀ PHẦN THẬP PHÂN. VÍ
DỤ NHẬP 3.14 THAY VÌ 3,14
Question:
-732.972
-827.027
125.784
-1.784
27.073
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 5/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
2.2-The result bending at the position C, MeqC (Nmm)
28.758
11.215
1.335
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 6/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
Câu hỏi 5
Hoàn thành
A structure is shown in Fig. Two plates are connected by a group of 4 bolts using the bolt connection with a clearance. The bolts are placed
at the position illustrated in Fig. Two forces acting to the structure includes P1 = 1000 N and P2 = 500 N. The dimensions are given as L1
=900 (mm) and L2 = 400 (mm) and a =300 (mm). The coefficient of friction between some plates is f = 0.2. The safety factor is k =1.5. The
material of bolts has an allowable tensile stress [σk] =110 (MPa).
CHÚ Ý:
NHẬP DẤU "CHẤM" GIỮA PHẦN NGUYÊN VÀ THẬP PHÂN, KHÔNG NHẬP DẤU PHẨY GIỮA PHẦN NGUYÊN VÀ PHẦN THẬP PHÂN. VÍ
DỤ NHẬP 3.14 THAY VÌ 3,14
1.1- Determine the magnitude of the force due to the shear load acting each bolt, FF (N)?
375
1.2- Determine the magnitude of the force due to the torque acting each bolt, FM (N)?
1833.333
1.3- Determine the magnitude of the force acting a bolt subjected to a maximum load, FMax(N)?
2208.333
16562.4975
d1 ≥ 15.787 (mm)
and choose the size of the bolt based on the reference table as below
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 7/8
7/27/22, 2:13 PM MiniProject: Xem lại lần làm thử
Bolts M6 M8 M10 M12 M16 M20 M24 M30 M36
d1, mm 4,917 6,647 8,376 10,106 13,835 17,294 20,752 26,211 31,670
Note: The answer is only a number. For example M6, You only enter 6 into the answer box.?
M 20
◄ Quiz_03
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=2437444&cmid=506305 8/8