Professional Documents
Culture Documents
Tolerances and Measuring Technnology - Nhom 01FIE: Câu hỏi
Tolerances and Measuring Technnology - Nhom 01FIE: Câu hỏi
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Đúng
From the assembly drawing, determine the limits of size of body hole 1, pulley hole 4 and pin 2 in the roller pulley wheel unit.
Select one:
a. Hole of the body 1: Dmin = Ø12,016 , Dmax = Ø12,043 ; Hole of the pulley wheel 4: Dmin = Ø11,987 , Dmax = Ø12,013 ;
Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
b. Hole of the body 1: Dmin = Ø11,087 , Dmax = Ø12,13 ; Hole of the pulley wheel 4: Dmin = Ø12,16 , Dmax = Ø12,43 ; Diameter
of the pin 2: dmin = Ø11,982 , dmax = Ø12.
c. Hole of the body 1: Dmin = Ø11,987 , Dmax = Ø12,013 ; Hole of the pulley wheel 4: Dmin = Ø12,016 Your answer is
, Dmax = Ø12,043 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12. correct.
d. Hole of the body 1: Dmin = Ø11,987 , Dmax = Ø12,013 ; Hole of the pulley wheel 4: Dmin = Ø11,982 , Dmax = Ø12 ; Diameter
of the pin 2: dmin = Ø12,016 , dmax = Ø12,043.
The correct answer is: Hole of the body 1: Dmin = Ø11,987 , Dmax = Ø12,013 ; Hole of the pulley wheel 4: Dmin = Ø12,016
, Dmax = Ø12,043 ; Diameter of the pin 2: dmin = Ø11,982 , dmax = Ø12.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 1/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Sai
Because of hard machining holes D = Ø40+0,016 and shafts d = Ø40 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø40+0,048 ; d = Ø40 . Your answer is
incorrect.
b. D = Ø40+0,040; d = Ø40 .
c. D = Ø40+0,048 ; d = Ø40 .
d. D = Ø40 ; d = Ø40 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 2/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Sai
Choose the suitable keywidth in order to assemble with the slot b = 10 in the part drawing that creates transition fit with Smax = 22μm and
Nmax = 11μm.
Select one:
a. b = 10-0,11.
c. b = 10-0,011.
d. b = 10±0,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 3/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Không trả lời
Select one:
a. Diagram 1.
b. Diagram 2.
c. Diagram 3.
d. Diagram 4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 4/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Không trả lời
From the fit between the housing hole and outer diameter of plain bearing on the assembly drawing, if housing bore is D = Ø48+0,025, outer
diameter d of plain bearing should be:
Select one:
a. d = Ø48 .
b. d = Ø48 .
c. d = Ø48±0,008.
d. d = Ø48-0,016.
Câu hỏi 6
Không trả lời
With a given fit having calculate limits of sizes of the hole and shaft
Select one:
a. Dmax = Ø35,06 ; Dmin = Ø34,085 and dmax = Ø35,01 ; dmin = Ø34,990.
The correct answer is: Dmax = Ø35,006 ; Dmin = Ø34,985 and dmax = Ø35,010 ; dmin = Ø34,990.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 5/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
Determine suitable diameters for driven helical gear bore D and shaft diameter d in one-stage gear reducer.
Select one:
a. D = Ø50 and d = Ø50-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 6/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Không trả lời
Choose proper outer diameter d of the plain bearing in order to assemble with the housing bore D = Ø50+0,025
Select one:
a. Ø50 .
b. Ø50+0,16.
c. Ø50 .
d. Ø50-0,016.
Câu hỏi 9
Không trả lời
Select one:
a. D3 ; D1 ; D2 ; D5 ; D4.
b. D1 ; D4 ; D2 ; D3 ; D5.
c. D3 ; D1 ; D2 ; D4 ; D5.
d. D5 ; D4 ; D2 ; D1 ; D3.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 7/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
Choose the type of fit for the cone gear 28 and shaft I of the below reduction gearbox.
Select one:
a. Transition fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 8/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
Select one:
a. Smin = 0,017
b. Smin = 0
c. Smin = 0,019
d. Smin = 0,006
Câu hỏi 12
Không trả lời
Figure 1
Figure 2
Select one:
a. Figure 1: Transition fit ; Figure 2: Clearance fit.
The correct answer is: Figure 1: Interference fit ; Figure 2: Clearance fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 9/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
It is known that D = Ø45, TD = 18µm, EI = - 25µm. Determine if the two holes with the actual dimensions Dt1 = Ø44,9955 and
Dt2 = Ø44,9755 meet the requirements?
Select one:
a. The first one is satisfactory while the second one is unrepairable defect.
c. The second one is satisfactory while the first one is unrepairable defect.
d. The second one is satisfactory while the first one is repairable defect.
The correct answer is: The second one is satisfactory while the first one is unrepairable defect.
Câu hỏi 14
Không trả lời
Choose the limits of size of gear hole and shaft in the below fit.
Select one:
a. Dmin = Ø28,002 , Dmax = Ø28,015 ; and dmin = Ø28 , dmax = Ø28,021.
The correct answer is: Dmin = Ø28 , Dmax = Ø28,021 ; and dmin = Ø28,002 , dmax = Ø28,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 10/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 11/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 16
Không trả lời
Choose the suitable shaft d in order to assemble with hole of the worn gear D = ø80H7 = ø80+0,030.
Select one:
a. d = Ø80 .
b. d = Ø80 .
c. d = Ø80 .
d. d = Ø80+0,19.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 12/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Determine the limits of size and tolerance for center distance L = 107±0,03 of the below part
Select one:
a. Lmin = 106,097 ; Lmax = 107,030 ; T = 0,03.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 13/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Choose the suitable hole of gear in order to assemble with the shaft diameter d = Ø35 in the part drawing.
Select one:
a. D = Ø35+0,25.
b. D = Ø35-0,025.
c. D = Ø35±0,0125.
d. D = Ø35+0,025.
Câu hỏi 19
Không trả lời
With a given fit having D = Ø45-0,025 mm, d = Ø45-0,016mm, choose the correct answer
Select one:
a. Smax= 25μm and Nmax = 16μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 14/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
With a given fit having D = Ø30+0,025mm, d = Ø30 mm, calculate the tolerance of the fit TS,N
Select one:
a. T
S,N = 0,023mm.
b. TS,N = 0,042mm.
c. T
S,N = 0,048mm.
d. T
S,N = 0,006m.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 15/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Determine suitable dimensions of hole Ø30 of the below part and a shaft in a fixed joint, of which the end face is clamped with the part by
3 bolts M8
Select one:
a. D = Ø30+0,021 ; d = Ø30 .
b. D = Ø30 ; d = Ø30+0,021.
c. D = Ø30-0,021 ; d = Ø30+0,016.
d. D = Ø30±0,009 ; d = Ø30-0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 16/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Choose a series of holes for assembling the following shafts Φ30 in order to create the clearance fit with Smax = 106μm and Smin = 40μm.
Select one:
a. D = Ø30±0,013.
b. D = Ø30-0,033.
c. D = Ø30±0,033.
d. D = Ø30+0,033.
Câu hỏi 23
Không trả lời
Select one:
a. D2
b. D3
c. D1
d. D4
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 17/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Select one:
a. The algebraic difference between the maximum and the minimum limit of size.
b. The algebraic difference between the maximum limit of size and the corresponding nominal one.
c. The algebraic difference between the nominal size and the limits of size.
d. The algebraic difference between the nominal size and the corresponding actual one.
The correct answer is: The algebraic difference between the maximum limit of size and the corresponding nominal one.
Câu hỏi 25
Không trả lời
Select one:
a. D = Ø120 ; d = Ø120±0,027.
b. D = Ø120-0,047 ; d = Ø120 .
c. D = Ø120 ; d = Ø120 .
d. D = Ø120 ; d = Ø120 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 18/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Select one:
a. Nmin = 0,016
b. Nmin = 0,033
c. Nmin = 0,014
d. Nmin = 0
Câu hỏi 27
Không trả lời
Choose the limits of size of plain bearing hole D and of piston pin d.
Select one:
a. Dmin = Ø17,989 , Dmax = Ø18 ; dmin = Ø18,006 ; dmax = Ø18,024.
The correct answer is: Dmin = Ø18,006 , Dmax = Ø18,024 ; dmin = Ø17,989 , dmax = Ø18.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 19/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
From the assembly drawing, determine the limits of size of the parts in the assembly unit.
Select one:
a. Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10 , Dmax = Ø10,015 ; Piston pin: dmin = Ø9,989 ,
dmax = Ø10,011.
b. Pin bore: Dmin = Ø10,013 , Dmax = Ø10,035 ; Bushing hole: Dmin = Ø9,989 , Dmax = Ø10,011 ; Piston pin: dmin = Ø9,985 ,
dmax = Ø10.
c. Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10,013 , Dmax = Ø10,035 ; Piston pin: dmin = Ø9,985 ,
dmax = Ø10.
d. Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10 , Dmax = Ø10,022 ; Piston pin: dmin = Ø9,985 ,
dmax = Ø10.
The correct answer is: Pin bore: Dmin = Ø9,989 , Dmax = Ø10,011 ; Bushing hole: Dmin = Ø10,013 , Dmax = Ø10,035 ; Piston pin:
dmin = Ø9,985 , dmax = Ø10.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 20/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 29
Không trả lời
Select one:
a. D = Ø35+0,025 and d = Ø35-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 21/22
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Choose the outer diameter d of plain bearing assembled with hole D of "a rocker arm" in an internal combustion engine.
Select one:
a. d = Ø15 ; D = Ø15-0,018.
b. d = Ø15 ; D = Ø15+0,018.
c. d = Ø15±0,0055 ; D = Ø15+0,018.
d. d = Ø15-0,011 ; D = Ø15+0,018.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098123&cmid=1147978 22/22