Professional Documents
Culture Documents
(Blended Learning) Midterm Quiz - Attempt Review
(Blended Learning) Midterm Quiz - Attempt Review
Đã bắt đầu vào Thứ sáu, 3 Tháng mười một 2023, 2:49 PM
lúc
Tình trạng Đã hoàn thành
Hoàn thành vào Thứ sáu, 3 Tháng mười một 2023, 3:56 PM
lúc
Thời gian thực 1 giờ 6 phút
hiện
Điểm 12,45 của 17,00 (73,24%)
Câu hỏi 1
Hoàn thành
If the drillship is traveling at “half a knot from the “safe zone”, 1 km away from the wellhead, to the wellhead (the “set point”), how long does it
take to get to the wellhead? (Source: Maersk Drilling video @9:09)
a. About 1 hour
b. About 2 hours
c. About 15 minutes
d. About 30 minutes
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 1/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 2
Hoàn thành
What type of drilling is shown in the photo below (Source: W01-02 slides)
a. Exploration drilling
b. Delineation drilling
c. Development drilling
d. Appraisal drilling
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 2/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 3
Hoàn thành
Name one type of well that is not labeled as an "exploration/wildcat," "appraisal/delineation," nor "development" well.
Câu hỏi 4
Hoàn thành
a. the toolpusher
c. the derrickman
d. the driller
e. the roustabout
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 3/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 5
Hoàn thành
A drillship drilled the vertical surface section to a total depth of 3,185 meters (10,450ft) measured from the drillfloor (the rotary table). The
water depth is 7,200 ft (2,195m). And the drillfloor is 100ft (30m) above the mean sea level.
How far into the subsurface did they drilled for this surface casing section? (or what is the total depth Below the Mud Line for this section).
a. 2,750ft
b. 960m
c. 3,150ft
d. 3,915ft
e. 4,115ft
960m
Câu hỏi 6
Hoàn thành
What type(s) of drilling rig can be considered to drill development wells at 600m water depth
a. semi-submersible rig
d. drilling barge
e. jackup rigs
semi-submersible rig
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 4/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 7
Hoàn thành
b. Onshore only
Câu hỏi 8
Hoàn thành
a. is the daily cost to the operator of renting the drilling rig and the associated costs of personnel and routine supplies.
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 5/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 9
Hoàn thành
Special system(s) that is/are unique for deepwater and ultra deepwater drilling is/are:
a. ROV system
Câu hỏi 10
Hoàn thành
a. pore pressure helps lower the effective stress felt by the rock matrix
b. abnormal pore pressure can cause lost circulation at a shallower depth as a kick move up
e. pore pressure depends on the fluid density (including the suspended solids in the fluid)
pore pressure helps lower the effective stress felt by the rock matrix,
abnormal pore pressure can cause lost circulation at a shallower depth as a kick move up
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 6/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 11
Hoàn thành
Câu hỏi 12
Hoàn thành
When drilling into an abnormal pressure, you often observe an increase in the ROP.
Chọn một:
Đúng
Sai
Câu hỏi 13
Hoàn thành
a. well test
c. leak-off test
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 7/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 14
Hoàn thành
Assuming the earth is a perfect sphere and has a uniform solid crust thickness with Poisson's ratio of 0.35
Câu hỏi 15
Hoàn thành
Bow
the foremost part of a ship
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 8/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
Câu hỏi 16
Hoàn thành
Calculate the bottom hole pressure when well has a mixture of different mud weights as follows:
TVD = 6,000ft
From surface to 500ft, MW = 10.0ppg
From 500-1,300ft, MW = 11.0ppg
From 1,300-bottom hole, MW = 11.5ppg
Provide your answer in psig unit (enter just the numbe, do NOT include the unit "psig")
Câu hỏi 17
Hoàn thành
b. SICP
c. SIDPP
WEBSITE
HCMUT
MyBK
BKSI
LIÊN HỆ
elearning@hcmut.edu.vn
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 9/10
23:09 03/11/2023 [Blended learning] Midterm quiz: Attempt review
https://e-learning.hcmut.edu.vn/mod/quiz/review.php?attempt=1581598&cmid=200761 10/10