Professional Documents
Culture Documents
Tolerances and Measuring Technnology - Nhom 01FIE: Câu hỏi
Tolerances and Measuring Technnology - Nhom 01FIE: Câu hỏi
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
With a given fit having d = Ø50 and D = Ø50 mm, calculate Smax , Smin , Nmax , Nmin of the fit.
Select one:
a. Smax = 11µm ; Smin = 16µm ; Nmin = 0 ; Nmax = 44µm.
b. Smax = 11µm ; Smin = Nmin = 0 ; Nmax = 44µm.
c. Smax = 44µm ; Smin = Nmin = 0 ; Nmax = 11µm. Your answer is
incorrect.
The correct answer is: Smax = 11µm ; Smin = Nmin = 0 ; Nmax = 44µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 1/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Đúng
Determine the limits of size and tolerance for center distance L between hole Ø16 and internal spline of the below part
Select one:
a. Lmin = 76,07 ; Lmax = 77,003 ; T = 0,06.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 2/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 3
Không trả lời
Choose the suitable limits of size for the spindle d and the hole D of the tailstock in an engine lathe.
Select one:
a. Dmin = Φ39,993 ; Dmax = Φ40 and dmin = Φ40 ; dmax = Φ40,011.
The correct answer is: Dmin = Φ40 ; Dmax = Φ40,011 and dmin = Φ39,993 ; dmax = Φ40.
Câu hỏi 4
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50-0,016.
b. D = Ø50-0,025 ; d = Ø50 .
c. D = Ø50 ; d = Ø50-0,025.
d. D = Ø50+0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 3/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 5
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50-0,025.
b. D = Ø50 ; d = Ø50 .
c. D = Ø50 ; d = Ø50 .
d. D = Ø50 ; d = Ø50 .
Câu hỏi 6
Không trả lời
With given shafts having d = Ø50 , choose the size of the holes D so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. ø50±0,012.
b. ø50 .
c. ø50-0,025.
d. ø50+0,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 4/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 7
Không trả lời
Which one is the clearance fit with the average clearance Stb = 38,5μm?
Select one:
a.
b.
c.
d.
Câu hỏi 8
Không trả lời
Select one:
a. Interference fit with the average interference Ntb = 29,5μm.
The correct answer is: Interference fit with the average interference Ntb = 26,5μm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 5/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 9
Không trả lời
With a given fit having D = Ø54 mm, d = Ø54+0,028 mm, calculate the tolerance of the fit TS,N
Select one:
a. 36μm.
b. 42μm.
c. 51μm.
d. 23μm.
Câu hỏi 10
Không trả lời
Limiting deviations of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. ES = -0,036 ; EI = -0,003 ; es = 0 ; ei = -0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 6/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 11
Không trả lời
With a given fit having D = d = Ø28, TD = 21μm, Nmin = 7μm, es = 0, Nmax= 41μm, determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø27,98 ; Dmin = Ø27,059 ; dmax = Ø28 ; dmin = Ø27,087
The correct answer is: Dmax = Ø27,98 ; Dmin = Ø27,959 ; dmax = Ø28 ; dmin = Ø27,987
Câu hỏi 12
Không trả lời
In a clearance fit, the maximum clearance Smax and the minimum clearance Smin are calculated by the following formulas:
Select one:
a. Smax = ES - ei and Smin = EI - es.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 7/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 13
Không trả lời
Choose the shaft diameter in order to assemble with the bore of the rolling bearing Ø65-0,012
Select one:
a. Ø65
b. Ø65±0,015
c. Ø65+0,03
d. Ø65-0,016
Câu hỏi 14
Không trả lời
Select one:
a. Stb = 150μm
b. Stb = 200μm
c. Stb = 80μm
d. Stb = 180μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 8/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 15
Không trả lời
Select one:
a. Nominal (basic) size
c. Limits of size
d. Tolerance
Câu hỏi 16
Không trả lời
Choose proper fits between helical gears and shaft portions 3, 4 as well as fits between sleeves and shaft portions 2, 5 of an intermittent
shaft in a double reduction gearbox.
Select one:
a. Clearance fit for shaft portions 3, 4; and transition fit for shaft portions 2, 5.
b. Interference fit for shaft portions 3, 4; and clearance fit for shaft portions 2, 5.
c. Transition fit for shaft portions 3, 4; and interference fit for shaft portions 2, 5.
d. Transition fit for shaft portions 3, 4; and clearance fit for shaft portions 2, 5.
The correct answer is: Transition fit for shaft portions 3, 4; and clearance fit for shaft portions 2, 5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 9/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Choose the proper diameter d of pin 1 assembled with body hole D of "a Cardan universal coupling".
Select one:
a. d = Ø16 ; D = Ø16 .
b. d = Ø16-0,011 ; D = Ø16 .
c. d = Ø16 ; D = Ø16-0,018.
d. d = Ø16±0,0055 ; D = Ø16 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 10/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
With the fits in the figures 1 and 2 below, calculate hole and shaft tolerances.
Figure 1
Figure 2
Select one:
a. Figure 1: TD = 25µm ; Td = 16µm. Figure 2: TD = 19µm ; Td = 30µm.
The correct answer is: Figure 1: TD = 25µm ; Td = 16µm. Figure 2: TD = 30µm ; Td = 19µm.
Câu hỏi 19
Không trả lời
Select one:
a. 41μm
b. 25μm
c. 16μm
d. 9μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 11/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
With a given fit of D = Ø42 and d = Ø42 , reselect the shaft so that the average of interference equals to 62,5μm.
Select one:
a. Ø42 .
b. Ø42 .
c. Ø42 .
d. Ø42+0,016.
Câu hỏi 21
Không trả lời
Because of hard machining holes D = Ø30 and shafts d = Ø30-0,010 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø30+0,030; d = Ø30 .
b. D = Ø30 ; d = Ø30-0,030.
c. D = Ø30 ; ; d = Ø30 .
d. D = Ø30 ; D = Ø30 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 12/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
Suggest a suitable type of fit for the diameter Ø60 between the tool holder 1 and the base plate 2 of the square tool post below.
Select one:
a. Interference fit or transition fit.
b. Clearance fit.
c. Transition fit.
d. Interference fit.
Câu hỏi 23
Không trả lời
With a given fit having D = d = Ø48, TD = 25μm, Nmax = 33μm, es = 0, Smax = 8μm, determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø47,992 ; Dmin = Ø47,967 ; dmax = Ø48 ; dmin = Ø47,984.
The correct answer is: Dmax = Ø47,992 ; Dmin = Ø47,967 ; dmax = Ø48 ; dmin = Ø47,984.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 13/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
Tolerances of diameters d1 = Ø30 and d2 = Ø50 of the shaft are not shown on the part drawing, so they can be specified as follows:
Select one:
a. d1min = Ø29,61 ; d1max = Ø30 and d2min = Ø49,67 ; d2max = Ø50.
The correct answer is: d1min = Ø29,67 ; d1max = Ø30 and d2min = Ø49,61 ; d2max = Ø50.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 14/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
With the number of holes and shafts is N = 10.000 pieces, select the diagram in which the probability of clearance is greater than the one
of interference when assembling at random.
Select one:
a. Diagram 2
b. Diagram 4
c. Diagram 3
d. Diagram 1
Câu hỏi 26
Không trả lời
Select a transition fit in which the probability of interference is a little greater than the one of clearance when assembling at random.
Select one:
a. D = Ø50+0,025 ; d = Ø50±0,008.
b. D = Ø50+0,025 ; d = Ø50 .
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50-0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 15/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 27
Không trả lời
From the fit between gear and shaft on the assembly drawing, choose the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø39,975 , Dmax = Ø40 ; and dmin = Ø40 , dmax = Ø40,016.
The correct answer is: Dmin = Ø39,975 , Dmax = Ø40 ; and dmin = Ø39,984 , dmax = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 16/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Select one:
a. D = Ø50 .
b. D = Ø50-0,016.
c. D = Ø50+0,016.
d. D = Ø50±0,008.
Câu hỏi 29
Không trả lời
With a given fit having D = Ø50-0,025 and d = Ø50 , determine the average interference of fit.
Select one:
a. 43μm
b. 22,5μm
c. 40μm
d. 23,5μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 17/18
10/20/23, 3:52 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
With the number of holes and shafts is N = 10.000 pieces, select the diagram in which the probability of clearance is bigger than the one of
interference when assembling at random.
Select one:
a. Diagram 2
b. Diagram 1
c. Diagram 3
d. Diagram 4
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5098147&cmid=1147978 18/18