Professional Documents
Culture Documents
SILVERLINE SERIES
SUBMERSIBLE PUMPS - 3” & 4”
50Hz
small production unit he started kept growing rapidly. Now, after four
C . R . I . I S O N E A M O N G
the few pioneers in the world to produce 100% stainless steel
THE INFRASTRUCTURE
of C.R.I. is pretty comprehensive with state-of-the-art machineries
and a high potential R&D wing, all within its own covered area of
with ISO 9001 & 14001 certification. The R&D team always stays in
tune with the changing scenario and seldom fails in coming up with
N E E D L E S S T O S A Y ,
behind this legendary growth lies the untiring, innovative,
GENERAL INFORMATION
SILVERLINE SERIES
The conditions below apply to the curves shown on the following pages.
a. The Performance curves show pump performance at rated speed, voltage and @ 10ft minimum submergence.
b. The measurements were made with airless water at 20°C. When pumping liquids with a
density higher than that of water, motors with correspondingly higher outputs must be used.
c. Pipe friction losses have not been included in the performance curves and performance tables.
e. Q/H : The curves are inclusive of check valve and suction inter-connector losses at the
actual speed.
h. The performance are at rated voltage and are only Indicative. Actual discharge depends on
availability of water in well, based on strength of water source, height of water column,
submergence of pump, etc.,.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
GENERAL INFORMATION
R - Reduced impeller
DEEPWELL RR - Further reduced impeller
SUBMERSIBLE PUMP NOMINAL MOTOR DIAMETER
(This digit will be applicable only when the
NOMINAL
pump is suitable for lesser dia motor)
PUMP DIAMETER
NUMBER OF IMPELLERS
TYPE OF MATERIALS OF
CONSTRUCTION (M.O.C.)
X X X S - XXX X X
GENERAL INFORMATION
Submersible Pumps
C.R.I. Submersible Pumps are the products of the expertise gained
from over four decades of experience, endurance and workmanship.
These products are engineered to perfection with utmost care and
stringent quality control at all stages to ensure a trouble free service.
Description : C.R.I. 3" & 4" Silverline series submersible pumps are
built with thermoplastic impellers, diffusers and inbuilt check valve. All
vital components of these pumps are made of corrosive resistance
thermoplastic and the shaft is of SS 304/431. Pumps are multi stage
centrifugal type. The optimal design of impellers and diffusers enables
the best possible hydraulic efficiency.
C.R.I. Submersible pumps can be offered with either C.R.I. 'W' Series,
water filled rewindable submersible motors / C.R.I. 'R' Series, Resin
Filled encapsulated (water lubricated) submersible motors / C.R.I. 'L'
Series Non-toxic liquid filled submersible motors or any other NEMA
standard motors.
Pumped Liquids
Clean, Thin, Non-aggresive, Non explosive, Clear, Cold, Fresh Water without abrasives, Solid particles or fibre
having the following characteristics
a) Temperature 33 °C (max.)
i) pH 6.5 to 8.5
Minimum Horizontal
Maximum operating pressure
cooling flow Vertical installation
Motor along the minimum
installation
motor 30°angle 3” Submersible pump 0.925 Mpa (9.25 bar)
3” & 4" 0.15 m/s 33 °C 33 °C 4” Submersible pump 2.5 Mpa (25 bar)
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
GENERAL INFORMATION
H (m )
300
90
80
250
70
200
60
50
150
40
100 30
S3V-1E S3V-1H
20
S3V-3F
50
10
0 0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
Q - (m³/Hr)
Q - (lps)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
Note : The mounting dimensions of these pumps are in accordance with manufacturers standards.
COMMITMENT RELIABILITY INNOVATION Pumping trust. Worldwide.
GENERAL INFORMATION
H - (m)
320
1000
280
800
240
200
600
160
400 120
80
200
S4P-10
S4P-1E
S4P-14
S4P- 8
S4P-2
S4P-5
S4P-3
S4P-4
40
S4P-18
0 0
0 2 4 6 8 10 12 14 16 18 20 22 24
Q - (m³/Hr)
Q - (lps)
0 1.0 2.0 3.0 4.0 5.0 6.0
0 16 32 48 64 80 96
Q - (US GPM)
Available types of materials of construction : Type - P&V the above performance curves are for specified materials of construction.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
GENERAL INFORMATION
Material of Construction
" "
NOMINAL DIA. 3 NOMINAL DIA. 4
PART NAME PART No.
TYPE - V TYPE - P TYPE - V
CHECK VALVE HOUSING 21.01 Nylon-6 (Polyamide) S.S - 304 Nylon-6 (Polyamide)
NORYL* / DELRIN/
IMPELLER 23.04 NORYL* NORYL* / DELRIN
LEXAN**
SUCTION INTER CONNECTOR 25.01 Nylon-6 (Polyamide) S.S - 304 Nylon-6 (Polyamide)
PUMP SHAFT HEXAGONAL 22.01 S.S - 304 S.S - 304 S.S - 304
Note : Type - V is available only for specific models, with 1¼" outlet size.
3” TYPE - V 4” TYPE - V
Part No. Part Name Part No. Part Name Part No. Part Name
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
GENERAL INFORMATION
Part No. Part Name Part No. Part Name Part No. Part Name
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
100
Flow Range : 0.5 - 2.5 m³/h
H - (feet)
H - (m)
S3
V S3V-1E
-1
E/3 2800 rpm
2
300
90 S3
V -1
E/3
0
S3
V -1
80 E/2
8
250
70
S3
V -1
E/2
200 2
60 S3V
- 1E
/20
50
150 S3V
- 1E/1
5
40
100 30
20
50
10
0 0
0 0.5 1 1.5 2 2.5
Q - (m³/h)
Q - (lps)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
0 2.5 5 7.5 10
Q - (US gpm)
Refer General Information for performance curve conditions and for other details.
Curve tolerance according to ISO : 9906, Annex - A.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
kW HP OD RP H2
Note : The mounting dimensions of these pumps are in accordance with Manufacturer standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
100
Flow Range : 0.7 - 3.2 m³/h
H - (feet)
H - (m)
S3V -
1H/24
S3V-1H
2800 rpm
300
90
S3V - 1
H/22
80 S3V -
1H/20
250
70
S3V -
1H/17
200 S3V -
60 1H/15
50
S3V -
1H/12
150
S3V -
40 1 H/10
20
50
10
0 0
0 0.5 1 1.5 2 2.5 3
Q - (m³/h)
Q - (lps)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
V S3V-3F
2850 rpm
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
RENEWED MODEL
S I LV E R L I N E S E R I E S
280
H - (feet)
H - (m)
800 S4P-2/32-R
240
220
700
200
600 S4P-2/23-R
180
160
500
S4P-2/18-R
140
400 120
100
300 S4P-2/12-R
80
S4P-2/08-R
200 60
S4P-2/07-R
S4P-2/06-R
40
100
20
0 0
0 0.5 1.0 1.5 2.0 2.5 3.0
Q - (m³/Hr)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
RENEWED MODEL
S I LV E R L I N E S E R I E S
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
RENEWED MODEL
S I LV E R L I N E S E R I E S
H - (feet)
440
H - (m)
S4P - 3E
1400 Flow Range - 2 - 4.7 m³/hr
50Hz
2900 RPM
1300 400
1200
360
1100
320
1000
280
900
S4P-3E/35-R
800
240
700 S4P-3E/26-R
200
600 S4P-3E/23-R
160
500
S4P-3E/16-R
400 120 S4P-3E/14-R
300 S4P-3E/11-R
80
S4P-3E/08-R
200
S4P-3E/07-R
S4P-3E/06-R
S4P-3E/05-R
40
S4P-3E/04-R
100
0 0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Q - (m³/Hr)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
RENEWED MODEL
S I LV E R L I N E S E R I E S
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
RENEWED MODEL
S I LV E R L I N E S E R I E S
H - (m)
H - (feet)
220
700
200
S4 P
-5/2
7 -R
600
180 S4P-
5 /25-R
160 S4P-5
/21-R
500
140
S4P-5
/17-R
400
120
100
300
S4P-5/1
1 -R
80
200 S4P-5/08-R
60
S4P-5/06-R
40
100
20
0 0
0 1 2 3 4 5 6 7 8
Q - (m³/Hr)
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
Q - (lps)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
RENEWED MODEL
S I LV E R L I N E S E R I E S
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
E F F IC IE N C Y ( %)
240
Flow Range : 0.75 - 2.1 m³/h
H - (feet)
H - (m)
S4P-1E
2900 rpm
220 S4 P
-1E
/34
700
S4P
-1E
h% 60
/33
200 40
20
600
180
S4P-
1 E/26
S4P-
160 1 E/25
500
140
400 S4P-1E
120 /18*
S4P-1
E/17*
100
300
S4P-1E/1
3 *
80
200 60
S4P-1E/08*
40
100
20
0 0
0 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0
Q - (m³/h)
Q - (lps)
0 0.1 0.2 0.3 0.4 0.5
0 2.5 5 7.5
Q - (US gpm)
* These Models are available in Type - 'V' construction as well.
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Available types of materials of construction : P and V. In case of M.O.C. type - V the third digit of the pump model "P" will be replaced with "V".
The given performance curves are same for Type - P & V.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
900
E F F IC IE N C Y ( %)
Flow Range : 1.1 - 3 m³/h
H - (feet)
H - (m)
S4P-2 S4P-2
/30
2900 rpm
800
240
h% 60
220 40
700
20
200 0
S4P-2/
22
600
180
160
500
S4P-2/16
140
400
120
100 S4P-2/11 *
300
80
S4P-2/07 *
200 60
S4P-2/05 *
40
100
20
0 0
0 0.5 1.0 1.5 2.0 2.5 3.0
Q - (m³/h)
Q - (lps)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Available types of materials of construction : P and V. In case of M.O.C. type - V the third digit of the pump model "P" will be replaced with "V".
The given performance curves are same for Type - P & V.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
H - (feet)
H - (m)
E F F IC IE N C Y ( %)
3/ 30
2900 rpm
700
S4P-
3/28
200
h% 60
600
180 40
20
160 0
S4P-
3/21
500 S4P-
3/20
140
400
120
S4 P - 3 / 1 5
100
300
80 S4P-3/11 *
200 S4P-3/08 *
60
S4P-3/07 *
40
100
20
0 0
0 1 2 3 4 5
Q - (m³/h)
Q - (lps)
0 0.2 0.4 0.6 0.8 1.0 1.2
0 5 10 15 20
Q - (US gpm)
* These Models are available in Type - 'V' construction as well.
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Available types of materials of construction : P and V. In case of M.O.C. type - V the third digit of the pump model "P" will be replaced with "V".
The given performance curves are same for Type - P & V.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
280
H - (feet)
900
S4P-
4/35
S4P - 4
2900 rpm
E F F IC IE N C Y ( %)
260
800
240
h%
220 60
700
S4P-4/27 40
200 20
0
S4P-4/
600 2 2
180
160
S4P-4
/20
500
140
S4P-4/14
100
300
S4P-4/11*
80 S4P-4/10 *
200 60
S4P-4/07 *
S4P-4/06 *
40 S4P-4/05 *
100
20
0 0
0 1 2 3 4 5 6
Q - (m³/h)
Q - (lps)
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
0 5 10 15 20 25
Q - (US gpm)
* These Models are available in Type - 'V' construction as well.
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Available types of materials of construction : P and V. In case of M.O.C. type - V the third digit of the pump model "P" will be replaced with "V".
The given performance curves are same for Type - P & V.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
200
E F F IC IE N C Y ( %)
H - (feet)
S4P - 5
2900 rpm
600 S4P-
180 5/27
80
h%
160 60
500
40
S4P-5/21
140 20
0
S4P-5/17
400
120
100
300
S4P-5/12
80 S4P-5/11
S4P-5/09
200 60 S4P-5/08*
S4P-5/06*
40
100
20
0 0
0 1 2 3 4 5 6 7 8
Q - (m³/h)
Q - (lps)
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
0 5 10 15 20 25 30 35
Q - (US gpm)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Available types of materials of construction : P and V. In case of M.O.C. type - V the third digit of the pump model "P" will be replaced with "V".
The given performance curves are same for Type - P & V.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
H - (m)
H - (feet)
E F F IC IE N C Y ( %)
2900 rpm
280
900
S4P
-8 /43
260
h%
800
240 60
220 40
700
200 S4P-8/ 20
32
600
180 0
160
500
S4P-8/2
150
3
400 120
S4P-8/17
100
300
80 S4P-8/13
200 60
S4P-8/08
40 S4P-8/06
100
S4P-8/04
20
0 0
0 2 4 6 8 10 12
Q - (m³/h)
Q - (l/s)
0 0.5 1 1.5 2 2.5 3
0 10 20 30 40 50
Q - (US gpm)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Available types of materials of construction : P and V. In case of M.O.C. type - V the third digit of the pump model "P" will be replaced with "V".
The given performance curves are same for Type - P & V.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
500 S4 P - Flow Range 6 - 15 m³/Hr
H - (feet)
10/28 S4P-10
H - (m)
150
50 Hz
2900 RPM
EFFICIENCY
S4P - 1
140 0/26
450
130
h% 80
400 S4P - 1
0/22
120 60
40
110 S4P - 1 20
350 0/20
0
100
S4P - 1
0 /17
300
90
S4P - 1
0 /15
80
250
70
S4P - 10/12
200 60
S4P - 10/10
50
S4P - 10/08
150
40 S4P - 10/07
S4P - 10/06
S4P - 10/04
20
S4P - 10/03
50
10
0 0
0 2 4 6 8 10 12 14
Q - (m³/h)
Q - (lps)
0 0.5 1 1.5 2 2.5 3 3.5 4
0 10 20 30 40 50 60
Q - (US gpm)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
S4P-10/03
S4P-10/04
S4P-10/05
S4P-10/06
S4P-10/07
S4P-10/08
S4P-10/10
S4P-10/12
S4P-10/15
S4P-10/17
S4P-10/20
S4P-10/22
S4P-10/26
S4P-10/28
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
140
H - (feet)
450
EFFICIENCY
S4P S4P - 14
- 14/24 2900 rpm
130
400 S4P
- 14/22
120 h%
60
110
350
40
100 S4P -
1 4/17
20
300
90 S4P -
1 4/16
0
80
250 S4P - 1
4 /13
70 S4P - 1
4 /12
S4P - 1
4 /11
200 60 S4P - 1
4 /10
50
150
40 S4P - 14/07
20
S4P - 14/03
50
10
0 0
0 2 4 6 8 10 12 14 16 18 20
Q - (m³/h)
Q - (lps)
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
0 10 20 30 40 50 60 70 80 90
Q - (US gpm)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
kW HP OD RP H2
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
140
H - (m)
H - (feet)
E F F IC IE N C Y ( %)
130 2900 rpm
400
120
S4 P
-18/
2 8 h%
110 60
350 S4 P-
18/26
100 40
300
90 S4P-18 20
/22
S4P-18
80 /20 0
250
70
200 60
S4P-18
/14
S4P-18
/13
50
150
40 S4P-18
/09
100 30
S4P-18/0
6
20
S4P-18/04
50
10
0 0
0 2 4 6 8 10 12 14 16 18 20 22 24 26
Q - (m³/h)
Q - (l/s)
0 1 2 3 4 5 6 7
0 10 20 30 40 50 60 70 80 90 100 110
Q - (US gpm)
Refer General Information for performance curve conditions and for more details.
Curve tolerance according to ISO : 9906, Annex - A
Pumping trust. Worldwide.
S I LV E R L I N E S E R I E S
Note : The mounting dimensions of these pumps are in accordance with Manufacture standards.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
FRICTION LOSS IN METERS FOR 10 METERS LONG NEW STEEL GALVANIZED PIPE (C = 140)
0.50 0.364
1.00 1. 315 0.341
1.25 1.988 0.516 0.246
1.60 3.140 0.814 0.388
2.00 1.231 0.587
2.50 1.861 0.888 0.282
3.2 2.940 1.402 0.446 0.126
4.0 2.120 0.674 0.190
5.0 3.205 1.019 0.288
8.0 2.433 0.887 0.313
10.0 3.678 1.038 0.474 0.131
12.5 1.570 0.716 0.198
16 2.479 1.131 0.312 0.111
20 3.747 1.710 0.472 0.167
25 2.585 0.713 0.253 0.106
32 4.033 1.127 0.400 0.157
40 1.704 0.605 0.252
50 2.576 0.914 0.351
60 1.281 0.534
80 0.182 0.910
100 3.299 1.376
125 0.051
FRICTION LOSS IN METERS FOR 10 METERS LONG NEW RPVC PIPE (C = 150)
Nominal Pipe Outer dia
In mm / inches 40/ 50/ 63/ 75/ 90/ 110/ 125/ 140/ 160/
Volume rate 1½” 2” 2½” 3” 3½” 4¼” 5” 5½” 6¼”
of flow lps
0.50 0.074
1.00 0.268
1.25 0.405 0.131
1.60 0.640 0.211
2.00 0.967 0.310
2.50 1.462 0.483 0.150
3.20 2.309 0.762 0.250 0.106
4.0 3.491 1.153 0.377 0.160
5.0 1.742 0.571 0.242
8.0 4.161 1.363 0.577 0.237
10.0 2.060 0.873 0.358 0.133
12.5 3.114 1.319 0.542 0.201
16 4.919 2.084 0.856 0.317 0.172
20 3.151 1.293 0.479 0.260
25 1.955 0.725 0.392 0.225 0.117
32 3.089 1.145 0.020 0.355 0.184
40 1.731 0.937 0.537 0.279
50 2.617 1.416 0.812 0.421
60 3.008 1.985 1.138 0.590
80 3.382 1.939 1.006
100 2.931 1.521
125 2.299
Pumping trust. Worldwide.
PERMISSIBLE RANGE OF VOLUME RATES OF FLOW IN I/S THROUGH GALVANIZED STEEL PIPE TO LIMIT
FRICTION LOSSES TO 10 PERCENT OF THE PIPE LENGTH
PERMISSIBLE RANGE OF VOLUME RATES OF FLOW IN I/S THROUGH RPVC PIPE TO LIMIT
FRICTION LOSSES TO 10 PERCENT OF THE PIPE LENGTH
40 - - Up to 2.04
50 - - 2.04 - 3.70
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
FOR SINGLE PHASE 3 WIRE (D.O.L.) MOTORS MAXIMUM LENGTH OF COPPER CABLE
Motor Rating Cable Size Square Millimetres
0.37 0.5 120 200 320 480 810 1260 1900 2590 3580 4770 5920
230 0.55 0.75 80 130 220 320 550 850 1290 1760 2430 3230 4000 MAXIMUM
VOLT 0.75 1.0 60 100 170 250 430 670 1010 1380 1910 2550 3460 LENGTH
IN
1.1 1.5 40 70 120 180 300 470 710 980 1360 1850 2320
50Hz METRES
1.5 2.0 30 60 90 130 230 360 550 760 1060 1440 1820
FOR THREE PHASE 3 WIRE (D.O.L.) MOTOR MAXIMUM LENGHT OF COPPER CABLE
Motor Rating Cable Size Square Millimetres
0.75 1.0 410 680 1090 1640 2780 4330 6570 9010
1.1 1.5 300 500 810 1210 2060 3200 4850 6640 9220
1.5 2.0 220 370 590 880 1500 2340 3560 4890 6830 9230
2.2 3.0 150 250 400 600 1030 1600 2440 3350 4680 6340 7990
3 4.0 110 190 310 460 790 1230 1880 2590 3630 4930 6230
3.7 5.0 90 150 240 370 630 980 1490 2050 2870 3900 4920
4 5.5 80 140 230 340 590 920 1390 1910 2670 3600 4520
4.5 6.0 70 130 220 320 550 860 1310 1790 2510 3390 4260
MAXIMUM
380-415
5.5 7.5 60 110 170 260 440 690 1060 1450 2030 2750 3460 LENGTH
VOLT
7.5 10 50 80 130 200 340 530 810 1110 1560 2120 2680 IN
9.3 12.5 60 110 160 280 440 670 920 1310 1780 2250 METRES
50Hz
11 15.0 50 90 130 230 360 550 750 1060 1440 1820
These are maximum length of cable in METRES from POWER SOURCE to MOTOR. Exceeding these length will void warranty.
Pumping trust. Worldwide.
FOR SINGLE PHASE 6 WIRE (S.D.) MOTORS MAXIMUM LENGTH OF COPPER CABLE
Motor Rating Cable Size Square Millimetres
Supply
kW HP 1.5 2.5 4 6 10 16 25 35 50 70 95 120 150 185 240
Volts
5.5 7.5 100 165 255 390 660 1035 1590 2170 3040 4120
7.5 10 70 120 190 300 510 800 1210 1765 2340 3180
9.3 12.5 90 165 240 420 660 1000 1380 1930 2670
13 17.5 70 120 165 300 465 720 970 1380 1870 2370
18.5 25 80 120 210 310 490 670 945 1290 1630 2030
37 50 100 160 250 345 480 660 825 1050 1200 1430
45 60 140 210 290 400 550 690 850 1000 1200 1460
56 75 110 170 240 340 460 580 720 840 1010 1230
75 100 90 130 180 260 350 440 550 650 780 950
112 150 120 160 220 280 350 400 480 580
These are maximum length of cable in METRES from POWER SOURCE to MOTOR. Exceeding these length will void warranty.
In view of continuous developments, the information / descriptions / specifications / illustrations are subject to change without notice.
Pumping trust. Worldwide.
FLOW RATE
Us barrel
litre litre cubic meter cubic foot cubic foot per Imp.gallon US gallon
per day
per second per minute per hour per hour minute per minute per minute
3 3 Is barrel/d
l/s l/min m /h ft3/h ft /min Imp.gal./min Us gal./min
(Petroleum)
1 60 3.6 127.133 2.1189 13.2 15.85 543.439
0.017 1 0.06 2.1189 0.0353 0.22 0.264 9.057
0.278 16.667 1 35.3147 0.5886 3.666 4.403 150.955
0.008 0.472 0.0283 1 0.0167 0.104 0.125 4.275
0.472 28.317 1.6990 60 1 6.229 7.480 256.475
0.076 4.546 0.2728 9.6326 0.1605 1 1.201 41.175
0.063 3.785 0.2271 8.0209 0.1337 0.833 1 34.286
0.002 0.110 0.0066 0.2339 0.0039 0.024 0.029 1
LIQUID
Cubic meter litre Millilitre Imp. gallon US gallon cubic foot
m
3
l ml Imp. Gal US gal ft3
1 1000 1 x 10
6
220 264.2 35.3147
0.001 1 1000 0.22 0.2642 0.0353
-6 -4 -4 -5
1 x 10 0.001 1 2.2 X 10 2.642 x 10 3.53 x 10
0.00455 4.546 4546 1 1.201 0.1605
0.00378 3.785 3785 0.8327 1 0.1337
0.0283 28.317 28317 6.2288 7.4805 1
LENGTH
millimeter centimeter meter inch foot yard
mm cm m in ft yd
1 Kilometer = 1000 metres = 0.62137 miles 1 mile = 1609.37 metres =- 1.60934 kilometers
MASS
kilogram pound hundred weight tonne ton long short ton
kg lb (cwt) t tn sh tn
-4
1 2.205 0.0197 0.001 9.84 x 10 0.0011
-4 -4 -4
0.454 1 0.0089 4.54 x 10 4.46 x 10 5.0 x 10
50.802 112 1 0.0508 0.05 0.056
1000 2204.6 19.684 1 0.9842 1.1023
1016 2240 20 1.0161 1 1.102
907.2 2000 17.857 0.9072 0.8929 1
TEMPERATURE
To Convert From To Use Formula