Professional Documents
Culture Documents
Ltd
4 Handles Cryolipolysis
User Manual
Zhengzhou PZ Laser Slim Technology Co.Ltd
Warning
Dear users:
Thanks for using our company's products, in order to fully make use of the product, we sincerely suggest
follows:
◆◆Please read the instruction in detail and keep it well for further reading and consulting.
◆◆Please follow the instruction to fit and operate the machine correctly.
◆◆It forbids others to open and remove the mainframe except the authorized people in the company.
◆◆It forbids others to change and maintain the machine except the professional engineer.
This product does not belong to medical treatment, please don’t use for disease treatment!
Zhengzhou PZ Laser Slim Technology Co.Ltd
Contents
Chapter 1--Safety:-------------------------------------------------------P5
Chapter 4---Installation-------------------------------------------------P13
Chapter 6--Treatment--------------------------------------------------------P19
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
3
Zhengzhou PZ Laser Slim Technology Co.Ltd
7-2 Contradictions
7-4 Contact Us
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
4
Zhengzhou PZ Laser Slim Technology Co.Ltd
Chapter1 Safety
Safety always as the important point to be put in the first place. On the premise of using the machine in right way,The
design of the equipment is safe and convenient for both operators and patients.
Warning:
Described in below are the most important safety-related characteristics. Please do pay attention and follow, or will cause
unnecessary trouble.
★ Electric Safety
(1)Key Switch :It aims to avoid the people to use the machine without permission, Please remove the key when
not use the machine.
(2 )This equipment has two levels input power voltage, which is AC110V(PZ-838A), AC220V(PZ- 838). Please
make sure to choose the right power voltage for the machine.
(3)Only after turning off the machine and pulling out the power plug for 10 minutes(to ensure 100% release the left
( 4 ) Inside the shell has dangerous high voltage, so nobody is allowed to dissemable the spare parts but our factory
appointed engineers.
(5)Don’t wet the host or spray liquid on the host. It will break the equipment and cause electric shock. Please do not try
opening the handle protective shell, which will cause the handle broken.
(6)Please do not start the machine when finding host or treatment handle has water leakage.If water lekage happen
during the treatment, operators should power off the machine immediately.
(7)Make sure your power outlet has protective grounding wire and in safe condition.
★ Treatment Safety
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
5
Zhengzhou PZ Laser Slim Technology Co.Ltd
Considering safety reason, some groups should be taken careful treatment, while some are forbidden to give the fat
freezing treatment.
★ Fire Protection
(1)Please do not use the machine under inflammable and explosive environment.
(2)After disinfection, please do not start up the machine until medical alcohol be dried totally.
(4)Please unplug the power cord if the machine needs to be placed long time under no use.
★ Security Labels
(2)“F250V L7A”and“F250V L20A” represents the fuse type and rated value.
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
6
Zhengzhou PZ Laser Slim Technology Co.Ltd
Name Icon
Chin Handle
CPC head
Fat clipper
Holder
Power Line
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
7
Zhengzhou PZ Laser Slim Technology Co.Ltd
4 Gas Nozzle
Bellow is standard Packing List, which can be adjust according to customers different requirements.
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
8
Zhengzhou PZ Laser Slim Technology Co.Ltd
1 Host 1
1 Chin handle
3 Key 2
“F250V L20A”Fuse
4 Fuse 2
( 2 ) Model PZ-838B matches
5 Gray Bandage 2
7 Power Line 1
10 Fat Clipper 1
Anti-freeze
11 5
Membrane(60g)
12 Holder 1
14 Screw Driver 1
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
9
Zhengzhou PZ Laser Slim Technology Co.Ltd
★ Main Parameters
(3)Heating Temperature:37℃~42℃
(4)Cooling Temperature:-11℃~5℃
(5)Vacuum Pressure:10~80Kpa
(8)Volume: 135cm×67cm×75cm
★ Operational Reliability
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
10
Zhengzhou PZ Laser Slim Technology Co.Ltd
Chapter 4 Installation
★ Installation Steps
(1)Open packing and put the host on the smooth ground carefully.
(2)Put the holder in the host socket, put the screw in.
(3)Install the cryo handle holder on the host, put the screw in
(4)Install the cryo handle, and put them on the handle holder.
(5)Installation finished.
Notes:Before taking following steps,please make sure you are familiar with the whole machine structure(Find more
details in Chapter 2)
(5)Add water until there is water flowing out from the Overflow socket,then remove water funnel. Please leave the
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
11
Zhengzhou PZ Laser Slim Technology Co.Ltd
( 8 ) After turning on the machine for operation, more water need to be added.When thee water overflow from the
Attention:
1. Please do add water when first use the machine
3. The water must be purified deionized water or distilled water. Mineral water and tap water are forbidden to use, in
If need to release all the water in the water tank, plug the white CPC head on the water outlet. After the
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
12
Zhengzhou PZ Laser Slim Technology Co.Ltd
This chapter mainly introduces the systematic operation steps, not the actual treatment methods. For professional and
(1)Please make sure the installation finished, and machine already b added right coolant water
(3)Rotate the key switch 90 degrees clockwise to start up the machine(Please start treatment after leave machine 2
(1)Turn on the machine, you will see the following interface with logo(can be customized), as Figure 3 shows:
Figure 3
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
13
Zhengzhou PZ Laser Slim Technology Co.Ltd
Figure 3
(3)Then machine will start self-inspection condition, mainly inspect water flow and treatment handles.When
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
14
Zhengzhou PZ Laser Slim Technology Co.Ltd
Figure 4
1:The part to control Channel1 and parameter setting area(Specific meaning on the following form )
For example: As icon shows ,handle 1 stands for the treatment handle(160) is
in channel 1;
b:This area shows cooling temperature(default as 5℃). Operators can adjust it (-11~
c:This area shows the result of water flow detection. If no water flow, red icon will
occur to give warning; If have water flow, blue icon will appear.
d:Clicking this area can switch back and forth between ready for work and stand by.
e:This area shows the treatment time,count from the treatment handle begin to work to
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
15
Zhengzhou PZ Laser Slim Technology Co.Ltd
(1) Shows the handles under Channel 3 now, all 4 handles parameters can
be set separately
& to adjust before treatment starts. It can not be changed once treatment begains.
Clicking & to adjust before treatment starts. It can not be changed once
treatment begains.
(default as 60min )
Clicking & to adjust before treatment starts. It can not be changed once
treatment begins.
Clicking & to adjust before treatment starts. It can be changed once treatment
begins.
When it shows , the small screen is locked, all parameters can’t be adjusted.
When it shows , the small screen is unlocked, all parameters on small screen can be
adjusted.
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
16
Zhengzhou PZ Laser Slim Technology Co.Ltd
2:The control area and parameter showing area of Channel 2(same as Channel1)
3:The control area and parameter showing area of Channel 3(same as Channel1)
4:The control area and parameter showing area of Channel 4(same as Channel1)
5:When all the treatment handle are under situation,clicking to enter the self-cleaning screen(as follow
table shows)
6:Clicking to see the treatment parameter table(according to fat layer) for reference(As follow table shows)
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
17
Zhengzhou PZ Laser Slim Technology Co.Ltd
The second press = Keep the vacuum(press when fat occupy almost 2/3 cup) The second press = Stop the treatment
Attention:
Please obey following rules in case bring you troubles during usage.
(1)Pulling out and plug the treatment head are forbidden when the machine under working, it may damage the handle.
Please do remove and change the handle after stop the machine.
(2)Please change the water every 3 months (or shorter times). See more details in previous chapter.
(3)When the atmosphere temperature too low, or the machine was put long time for no use, please do get the host
(4)In order to make the machine working at good cooling condition, please do not put the machine against the wall and
(5)Please do not use the machine under humid and strong sunlight environment.
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
18
Zhengzhou PZ Laser Slim Technology Co.Ltd
Chapter 6 Treatment
This machine is equipped with 4 handles so that can treat 4 areas simultaneously. While for the same customer, we
★ Treatment Steps
(3)Check the thickness of the fat with the help of fat calipers. Then set off parameters(such as the cooling temperature
(6)First, take out the small antifreeze membrane and smear the edge and inside of cooling fat dissolving handle.
(9)When giving waist and abdomen treatment, best with sitting position, making upper body and thigh to 90 degrees
(10)Click to start the machine. When the icon changes from to ,the host is ready for working
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
20
Zhengzhou PZ Laser Slim Technology Co.Ltd
(11)Hold the cooling treatment handle to suck the treated area gently as following picture shows. Press the control
(12)The first press = start vacuum to suck the fat, treatment starts
The second press = Keep the vacuum(press when fat occupy almost 2/3 cup)
(13)When treatment begins, if necessary, can use bandage to fix the handle as follow picture shows:
(14)When the first area treatment start timing, the second area treatment can be started.The operation same as the first
area.
★ Treatment Tips
After treatment, damage, minor frostbite, skin pigment may occur at the treated area. With proper care, skin will back to
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
21
Zhengzhou PZ Laser Slim Technology Co.Ltd
(2)The treatment without anti-freeze protection is banned strictly. During treatment, please ensure anti-freezing
membranes completely cover the therapeutics part, otherwise will cause frostbite, ect.
Please do choose the qualified anti-freeze membranes(consumables, customer need to buy on self)for the treatment to
ensure safety.
If the liquid in anti-freezing membrane is too little (normally when open the package, you can see there is little liquid in
bag or the membrane is very moist), please do not use. Abundant liquid can well protect the skin from been frostbite.
(3) For customers who use for the first time, users shouldn’t choose below -8 degree to -11 degree, it’s only suitable for
fat layer thickness reaching 55mm or more. Please don’t use it if the fat is less than 55mm or it will have risk of cold
injury.
Clinical shown that exceptional customer with very low cold tolerance even can’t be used under -5℃, or will have
frostbite risk.
(4) For sucking in the skin at the beginning of the treatment, users can choose vacuum pressure (40-70kpa) after 3
minutes, please adjust pressure to 40kpa, long time in high pressure(40-70kpa) during the treatment will increase the risk
of skin blisters.
(5)Please do not treat a large area of body or treat the adjacent part of the body that you have been treated in the same
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
22
Zhengzhou PZ Laser Slim Technology Co.Ltd
For example:
If you operated part 1, please do not operate part 2 or part4, while part 3 is available for the treatment. If against this
regulation, light will cause the metabolic disorders, heavy then cause metabolic acidosis and the toxins from the body
doesn’t stranded.
(6) Generally, have the second cryolipolysis session good for consolidating the result.
But please leave 2 months interval between 2 cryolipolysis sessions for the same area.
(7) Operators can adjust according to referential parameters on screen.Of course can adjust the parameters according to
(8) After treatment, please Check the therapeutic part if the skin becomes harder or has lump, please use warm towel (42
Then the treatment part will have blebs, skin will scab after the bubble bursts, keep cold injury wound clean and dry,
apply frostbite cream for a few days and the wound would heal.
Because of frostbite, if you have bleb, mild on;y prevention of infection. Severe should aseptic puncture fluid, coated
(9) Please put the handle on the holder when not use it.When handle start working, the handle has to be put on the
treatment area.
★ Working Theory
As triglyceride in fats will be converted into solid in particular low temperatures. It uses advanced cooling technology to
selectively target fat bulges and dissolve fat cells through a gradual process that does not harm the surrounding tissues,
reduce unwanted fat, when fat cells are exposed to precise cooling, they trigger a process of natural removal that
gradually reduces the thickness of the fat layer. And the fat cells in the treated area are gently dissolved through the
★ Contradictions
(1)Patients who used by heart rare regulator, cardiac pacemaker, ECS (electro-cardioscanner);
(6)Patients with no independent expression consciousness and can not take care of themselves;
(7)Patients with metal materials in body (including metal teeth), pregnant women, cachexia, malignant tumor;
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
24
Zhengzhou PZ Laser Slim Technology Co.Ltd
(8)Severe hypertension and severe patients with cardiovascular and cerebrovascular disease;
(17)People with Severe diabetes and the elderly, young children, frail and so intolerant of cryotherapy;
(2)Children;
(5)The immune system has defects, scar formation history, physical disease;
(6)The people who has taken face-lifting or body has artificial thing.
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
25
Zhengzhou PZ Laser Slim Technology Co.Ltd
A1: Complete the treatment table--Ask and check the physical condition--locate the treated area--Paste antifreeze
membrane--Begin the treatment--Having a rest after finished, if no discomfort you could leave.
A2: Frozen wave controlled by non-invasive launcher precisely work on the treated parts, in particularly the parts of the
body that need to remove the fat cells, the whole process lasts about 1 hour.
A3: The second generation of freeze fat-dissolving method is developed by PZ slim technology and obtain patent:
according to the first generation of pure freeze system that will cause blood coagulation and tissue necrosis damage, we
improve to a safe fat-dissolving method that heat the skin first, make the blood and fat completely separation and then
began to the freeze fat-dissolving treatment. Especially we can do two parts in the same period of treatment. It saves time
A4: When the fat cells are exposed to precise cooling, they trigger a process of natural removal that gradually reduces the
thickness of the fat layer. And the fat cells will be removed through the body’s normal metabolization process mildly.
A5: The treatment is completely non-invasive, allows real-time normal activities such as work or sports. Treatment area
may be red, the situation may last several minutes or several hours. It may be also lead to local bruising and will subside
within a few weeks. Some patients will feel a little non-sensitive of the treatment area, it will subside in one to eight
weeks.
A6: Most of treatment course feels comfortable. In clinical trails, no treatment needs to use anesthesia or pain medication,
the patient can usually read freely, use computer, listen to music or have a rest
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
26
Zhengzhou PZ Laser Slim Technology Co.Ltd
A7: It depends on personal diet habits and vary with the corporeity. The efficacy after the treatment could maintain at
least 1 year in the user of reducing fat layer. The removed fat cells will gradually release the lipids and absorbed by
natural metabolism of the body. We expected that the removed fat cells returned to the treatment area are more slowly
than the invasive treatment such ad liposuction. However, irregular diet will lead to weight gain and may affect the
treatment results.
A8: Postpartum abdominal relaxation, regular exercise but no effect on thin waist, abdomen. Busy life and no time to do
exercise. Stool hoarding gastrointestinal squirm slowly. Can not refuse the temptation of delicious food. People
non-severe obesity who want to sculpture the fat of waist/belly and back fat.
A9:
Liposuction:
Notice: need general anesthesia whole body, may be leave scars, or appears body asymmetry and a risk of fatal.
Notice: You must control the need treatment area accurately, and appear swelling after treatment.
A10:Each course last about one hour, we recommend doing 2-3 treatments every two or three month.
WhatsApp:0086 18537185507
Email:amy@pzlaser.com
27
Zhengzhou PZ Laser Slim Technology Co.Ltd
A11: The freeze fat dissolving method is non-invasive treatment, both before and after treatment will not affect normal
A12: Using of exact computer program to control the temperature accurately within the safe range. The first 3~5 minutes
you have warm feeling, then the treatment area will feel cold gradually. In clinical experience, no one needs to use
medication for pain because of no invasive wound, therefore we will not feel painful unlike other liposuction surgery. At
the very beginning of treatment, there will be a little discomfort when the work head absorb fat powerfully, but soon will
disappear. After a while you will feel a little cooling paralysis, there is no special feeling. During treatment you could
Q13: Which group are not suitable for freeze fat dissolving method?
A13: People who have liver problems, the Raynaud’s disease, severe cold urticaria, cryoglobulinemia, cold fiber
hypoproteinemia, severe frostbite, hernia disease, severe diabetes and the elderly, young children, pregnant woman, frail
Attention:
Please obey the following suggestions, or may broken the machine and bring you unnecessary troubles.
(2)Please keep touch screen clean, potion or other stains are avoided.
(4)Do not use alcohol or detergent to clean the touch screen. If necessary, please use soft and clean cotton to wipe
carefully.
After the instrument is packed well, users can store it in a drafty room: the temperature is -10℃~50℃, relative humidity
If special handling measure have to be taken during transport or storage, the packaging shall be marked accordingly .
The permissible environmental conditions for transport and storage shall be marked on the outside of the packaging.
★ Contact US
Amy
Email:Amy@pzlaser.com
Website: www.pzlaser.com