Professional Documents
Culture Documents
Q2
Q2
Q14) How many cubes samples required for 110cum concrete on single day?
A: 18 B:12 C: 9 D: 6
A: 7 B: 14 C: 10 D: 28 days
Q19) The average strength of cubes at the end of 28 days should be ____
A: greater than fc’ by 15% B: Greater than or equal to fc’ C: equal to or less than fc’ by 15%
Q21) When casting , if the temperature of concrete mix is above 32C0, than how should you bring
thetemperature of the mix down to 32 or less?
Q22) structural element that holds the earth retaining wall is ____
A: damage of concrete element B: cracking of the element C: deflection become more than normal
D: All of above are correct
A: weak in compression and strong in tension B: strong in compression and strong in tension
C: strong in compression but weak in tension D: Enough strong in tensile strength for normal loads
Q32) Which part of a building transfer the load to the soil below the foundation?
Q39) Adding more water to concrete mix than its strength ______
A: 40 B: 75 C: 60 D: 50
Q47) The thickness of external fence wall plaster wall should be _____
Q50) The 6 concrete cubes are casted and are tested after ____
A: Fly ash B: silica fume C: GGBS D: Both Fly ash and slag
Q58) For normal size of blocks 200x200x400, the number of blocks required for 3mx5m wall is ___
Q63) The Sulfate content SO3 should not exceed _____in fine aggregate used for construction.
Q64) As per DM requirements, the yield strength of deformed bars should be ____ N/mm2
Q65) As per DM rules the lap length usually used is _____ for reinforcement.
Q69) Integrity test on Rcc piles is done after no sooner than ____days after casting
A: 3 B: 5 C: 10 D: 7
A: 1% B: 2% C: 0.5% D: 0.8%
Q71) For water used in construction, the Ph value is not _____ than 6.
A: near the column B: near the beam C: away from column D: anywhere
A: He should make same cubes next day B: He should not do the test and trust ready mix
C: He should check with the plant if they made the cubes or do core test.
Q75) What are the documents to be available with the contractor prior to the start of the project?
Q77) As per DM, tall buildings are those of minimum ______ meter height measured from ground.
Q80) After 7 days of compressive strength test of cubes, what is the minimum value should be accepted
A: Piling work B: direct contact with soil C: contact with water D: In All circumstances A,B,C
Q84) What is the standard size of cubes taken for compressive strength test?
A: to stop water seepage B: to make the footing strong C: to avoid evaporation D: None
Q86) If the 28 days result of the cubes compressive test is not satisfactory than what to do?
A: Do smidth test B: no need again C: make new cubes D: take core samples
Q90) Expansion joints are provided in big structure to avoid ____
A: sound effect B: Earth quake effect C: wind effect D: thermal effect or cracks
Q94) For plastering the exposed blocks wall, the mortar should be of ratio____
Q99) The bearing capacity of water logged soil can be improved by ____
Q104) concrete beam sides shuttering are removed minimum after ____
A: has more strength B: has high creep value C: get stronger with time D: is less brittle
A: water content B: gradation and admixtures C: aggregate shape and size D: All of above
Q111) Which of the following is not the characteristic of hard concrete ____
Q112) Fly ash a by product of coal fired electric generating plants is used to partially replaced OPC by _
A: by pouring in cone and measure the flow B: fill moulds C: hammer D: none
Q127) Depth of lean concrete bed placed at the bottom of wall footing is kept___
Q129) For plastering the exposed brick walls, the cement sand mortar should be ____
Q135) The entrained concrete is used in lining walls and roofs for making ____
Q145) The concrete slump recommended for beams and slab is ____Ans. 30 to 125mm
B: greater than 4 kg/cm2 but less than 20 kg/cm2 shear steel is provided
C: greater than 20 kg/cm2, the size of the section is changed. D: All of above
Q150) in pre-stressed member it is advisable to use _____Ans. High strength concrete and high tensile
steel bars
Q157) A construction joint is provided where ____Ans. Bending moment is less and shear force is small.
Q1) Why are vibrators not used in piles concrete during casting for compaction?
C: the concrete is of high slump and is self compacting D: vibrators are not allowed
Q2) As per DM the most suitable technique for deep compaction used in Dubai is ____
Q4) The foundation in which a cantilever beam is provided to join 2 footing is called ___
Q6) The compaction of concrete in the drilled pile hole is done by compressed air in case of ___