Professional Documents
Culture Documents
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
687 Max P Case 1 3084 218 588
687 Min P Case 2 -806.50 207 653
ULS 770 Max My Case 3 1705 993 183
827 Min My Case 4 1637 40.60 998
827 Max Mz Case 5 1978 71 1006
645 Min Mz Case 6 1651 287 61.68
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
728 Max P Case 1 1585 79 73
687 Min P Case 2 879 130 95
SLS 645 Max My Case 3 1459 232 156
847 Min My Case 4 1230 28 74
645 Max Mz Case 5 1459 232 156
770 Min Mz Case 6 1273 107 22.16
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
645 Max P Case 1 956 70 29
666 Min P Case 2 922 24 11
QP 645 Max My Case 3 956 70 29
666 Min My Case 4 922 22 11
645 Max Mz Case 5 956 70 29
645 Min Mz Case 6 945 31 8
ULS DESIGN FORCES FOR Pile (R=1)
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
693 Max P Case 1 3269 506 513
693 Min P Case 2 -714.32 247 518
ULS 693 Max My Case 3 2349 1090 151
776 Min My Case 4 3142 11.18 516
755 Max Mz Case 5 1928 415 534
693 Min Mz Case 6 1821 234 2.26
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
734 Max P Case 1 1703 175 40
693 Min P Case 2 997 103 32
SLS 734 Max My Case 3 1703 178 40
776 Min My Case 4 1049 56 24
672 Max Mz Case 5 1398 69 52
651 Min Mz Case 6 1382 67 0.6
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
651 Max P Case 1 1074 5 1
672 Min P Case 2 1040 2 0
QP 672 Max My Case 3 1042 10 1
672 Min My Case 4 1048 0 0
651 Max Mz Case 5 1074 5 1
672 Min Mz Case 6 1048 0 0
ULS DESIGN FORCES FOR Pile (R=1)
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
695 Max P Case 1 3330 334 367
695 Min P Case 2 -683.43 146 376
ULS 695 Max My Case 3 2407 634 106
855 Min My Case 4 1684 8.34 417
757 Max Mz Case 5 1979 243 419
653 Min Mz Case 6 1863 168 7.26
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
736 Max P Case 1 1742 113 19
695 Min P Case 2 1036 61 15
SLS 736 Max My Case 3 1742 115 19
653 Min My Case 4 1605 28 27
757 Max Mz Case 5 1482 83 36
653 Min Mz Case 6 1421 51 3
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
653 Max P Case 1 1113 10 4
674 Min P Case 2 1079 1 6
QP 653 Max My Case 3 1113 10 4
674 Min My Case 4 1088 0 1
653 Max Mz Case 5 1113 10 4
653 Min Mz Case 6 1102 6 1
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
737 Max P Case 1 1762 79 12
696 Min P Case 2 1055 40 8
SLS 737 Max My Case 3 1762 79 12
696 Min My Case 4 1281 16 21
675 Max Mz Case 5 1457 18 26
654 Min Mz Case 6 1441 37 3
ULS DESIGN FORCES FOR Pile (R=1)
Element Load Case No. Axial (KN) Myy (KNm) Mzz (KNm)
654 Max P Case 1 1133 9 3
675 Min P Case 2 1099 2 6
QP 654 Max My Case 3 1133 9 3
675 Min My Case 4 1099 0 1
654 Max Mz Case 5 1133 9 3
654 Min Mz Case 6 1131 6 1
i.e. = 1.64 % OK
The check for ultimate limit state of shaft is carried out in adsec computer program. The snapshot of summary of strength
analysis as P-M interaction curve is shown below:-
The check for serviceability limit state (Rare combination) of pile is carried out in adsec computer program. The snapshot of
summary of stress check in concrete & reinforcement is shown below:-
Summary of stresses in
concrete
Summary of stresses in
reinforcement
The check for serviceability limit state (Quasi-permanent combination) of shaft is carried out in adsec computer program.
i.e. = 1.14 % OK
The check for ultimate limit state of shaft is carried out in adsec computer program. The snapshot of summary of strength
analysis as P-M interaction curve is shown below:-
The check for serviceability limit state (Rare combination) of shaft is carried out in adsec computer program. The snapshot
of summary of stress check in concrete & reinforcement is shown below:-
Summary of stresses in
concrete
Summary of stresses in
reinforcement
The check for serviceability limit state (Quasi-permanent combination) of shaft is carried out in adsec computer program.
i.e. = 0.64 % OK
The check for ultimate limit state of shaft is carried out in adsec computer program. The snapshot of summary of strength
analysis as P-M interaction curve is shown below:-
The check for serviceability limit state (Rare combination) of shaft is carried out in adsec computer program. The snapshot
of summary of stress check in concrete & reinforcement is shown below:-
Summary of stresses in
concrete
Summary of stresses in
reinforcement
The check for serviceability limit state (Quasi-permanent combination) of shaft is carried out in adsec computer program.
i.e. = 0.41 % OK
The check for ultimate limit state of shaft is carried out in adsec computer program. The snapshot of summary of strength
analysis as P-M interaction curve is shown below:-
The check for serviceability limit state (Rare combination) of shaft is carried out in adsec computer program. The snapshot
of summary of stress check in concrete & reinforcement is shown below:-
Summary of stresses in
concrete
Summary of stresses in
reinforcement
The check for serviceability limit state (Quasi-permanent combination) of shaft is carried out in adsec computer program.
3/2 1/2
nmin = 0.031 k fck
L= 1000 = 0.3418882
0.33
Effective depth of section = 755.0 mm VRdc = Max ( 0.12 k (80 r1 fck ) + 0.15 scp ) bw d
fck = 35 Mpa (nmin +0.15scp ) bw d
fcd = 15.65 Mpa
fyk = 550 Mpa
Max Shear Capacity
2
Ac = 785398 mm n = 0.6 * ( 1- fck /310) */ fck in Mpa
2
As = 12881 mm = 0.5322581
Therefore,
2
ASW (min) /s = 774.469 mm /m
2
Asw/s provided 1047.2 mm /m OK
Design shear reinforcement (Refer clause 10.3.3.2 of IRC:112-2011)
Critical Load combination
Shear force acting on the section = 65.1 Tonne
Shear capacity of the section is = 40.5 Tonne
2
Axial Stress = 0.0 N/mm
β = 1
Reduced Shear force acting on the section VNS = 65.07 Tonne
n1 = 0.6
z = 0.9*deff
679.47 mm
2
scp = 0.025 N/mm
acw = 1 scp =0
= 1+ scp/fcd 0 < scp ≤ 0.25fcd
= 1.25 0.25fcd < scp ≤ 0.5fcd
= 2.5(1- scp/fcd) 0.5fcd < scp ≤ 1.0fcd
acw = 1.00163
-1
q = 0.5 sin [ 2*VNS / (acw * bw * z * n1 * fcd) ]
= 5.88 ◦ OK
q, Adopted = 21.8 ◦
Asw/s = VNS/z fywd cot θ
2
= 870.526 mm /m
2
Asw/s provided 1047.2 mm /m OK