Professional Documents
Culture Documents
The Multisensor is a compact unit that combines a light sensor for constant light
control and a passive infrared (PIR) presence detector to provide energy-saving
functions in a DALI system.
The light sensor measures reflected light from the surface directly beneath it.
The unit uses this information to maintain a constant light level by adjusting the
lamp outputs.
The PIR sensor enables the Multisensor to switch the lights on when its coverage
area is occupied, and off when it is unoccupied.
The sensor’s settings are adjusted using Helvar’s Designer or Toolbox software.
Due to its excellent detection performance, the Multisensor is especially suitable
for applications where small or slow movements take place for extended periods
of time, such as offices or classrooms. Since its detection sensitivity is less
dependent on movement direction than that of most PIR sensors, fewer units are
required to reliably cover a target area.
The unit can be mounted into a ceiling void or onto a solid surface using Helvar’s 1. PIR sensor
SBB-C (white) or SBB-CB (black) mounting box (sold separately). 2. Status LED
3. Light sensor
X-Axis Coverage
Technical Data
Wire section: 0.5 mm² – 1.5 mm² solid or stranded Presence detection coverage area: 46 m² @ 2.5 m mounting height
Cable rating All cables must be mains rated. Mounting hole diameter: 51 mm +/- 1 mm
Key Features
• Four individually programmable relays, normally open
and volt-free.
• Relays are internally isolated permitting separate
phases to be controlled in one unit.
• Each relay can be manually controlled using the
physical selection switch.
• All DALI functions are programmed with either DIGIDIM
Toolbox or Designer software.
• DIN-rail mounted and only 88 mm wide.
Connections
DALI
AC
45 mm
90 mm
DALI consumption: 2 mA
Mechanical data
Dimensions: 88 mm × 58 mm × 90 mm
Housing: DIN-rail case 88 mm wide
Weight: 300 g
Mounting: DIN rail (installation in switchgear/ 88 mm 58 mm
controlgear cabinet)
IP code: IP30
Wiring Diagram
L L
N N
DA+ DA+
DALI DALI
DA– DA–
Key Features
• High-inrush specification relays (single pole, normally open).
• Wired override input to allow for external triggers.
• LED segment display and push buttons.
• Can operate as:
◦◦ 8 individual channels (8 × 1)
◦◦ 4 sets of 2 channels (4 × 2)
◦◦ 2 sets of 4 channels (2 × 4)
Connections
SDIM/ OVER-
DMX RIDE RELAYS RELAYS
Relay 5
Relay 6
Relay 7
Relay 8
TERM
OVR
0V
0V
SC
B
(100–240) VAC
Relay 1
Relay 2
Relay 3
Relay 4
DA-
DA+
SC
N
L
Key Features
• Support for 128 DALI devices (64 DALI devices on each subnet).
• Certified DALI-2 Single Master - DALI-2 Lighting (Control Gear), not DALI-2
controls (Control Devices)
• Built-in real-time clock.
• Can be networked together to form large scalable systems.
• Provides local as well as central control if required.
• Compatible with other Helvar routers (905/920/950).
• Integration with other building systems.
• Universal supply input.
Compatibility: DALI and DALI-2 Lighting (Control Gear), DigiDim Controls, NOT DALI-2 (D2) Controls (Control Devices)
Helvar Oy Ab, Keilaranta 5 FI-02150 Espoo, Finland www.helvar.com 1
Dimensions (mm)
160
45 100
58
Installation
AC
DALI 1 and 2
ETHERNET
Technical Data
DALI cable: 2-wire mains rated, 0.5 mm² – 2.5 mm² Mounting: DIN Rail. Keep mains and DALI wiring separate from
Ethernet cable.
Max. length: 300 m @ 1.5 mm²
IP code: IP30 (IP00 at connectors)
Ethernet: 1 × RJ45 10/100 Mb/s, Cat 5E up to 100 m (Auto MDI/
MDI-X crossover)
Operating and storage conditions
Mains supply: 100 VAC – 240 VAC (nominal) Relative humidity: Max. 90 %, noncondensing
Safety: EN 61347-2-11
Key Features
• Out-of-box operation. No programming required when
using DIGIDIM slider, rotary, or push-button panels. For
Load & Supply wiring
scene panels, ‘preset download’ must be carried out.
• Input voltage fluctuation compensation ensures stable
output levels with fluctuating incoming mains levels.
• Group-selection switch for quick and simple
programming.
• Operating-mode switch (leading- or trailing-edge
dimming).
• Overcurrent, power and temperature protection.
• DIN-rail mounted and only 70 mm wide.
Additional Functions
The following functions may be programmed using the
Toolbox or Designer software:
• Max./Min. levels, Fade times*, Scenes* and Groups*
• Dimmer status report DALI
• System failure level/ignore
• Power on level
• Power on to last level
45
90
Ambient temperature: 0 °C to +40 °C
Above this temperature, derate
according to the adjacent graph.
Relative humidity: Max. 90 %, noncondensing
Storage temperature: –10 °C to +70 °C
Conformity and standards 70 58
EMC emission: EN 55015
EMC immunity: EN 61547
Connections
Safety: EN 61347-2-11
Environment: Complies with WEEE and RoHS
directives.
Software compatibility
Designer: 4.1 or later
Toolbox: All versions
Group-Selection Switch
Operating-Mode Switch
DALI IN DALI OUT