Professional Documents
Culture Documents
Rev.
Prepared Reviewed Approved Realease date Revision Description
No.
00 MES GPT ZED 23-June-2023 ISSUED FOR APPROVAL
Page 2 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
TABLE OF CONTENT
Chapter -1 Design Considerations (General). .............................................................................................. 4
1.1 Design Scope of work ...................................................................................................................................... 4
1.2 Reference drawings/documents .................................................................................................................... 5
1.3 DESIGN LOADS, DESIGN & BUILDING CODES ........................................................................................... 7
1.3.1 General Loading & Code Criteria................................................................................................................................... 7
1.3.2 Dead Load......................................................................................................................................................................... 8
1.3.3 Collateral Load ................................................................................................................................................................. 9
1.3.4 Live Load ......................................................................................................................................................................... 10
1.3.5 Seismic Load ................................................................................................................................................................... 11
1.3.6 Wind Load....................................................................................................................................................................... 12
Page 3 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Introduction
This document provides information on design philosophy & Calculation input, output for the “THE VILLAGE
MALL” in “AL RIQAIBAH 2, AL SIYUH SUBURB, SHARJAH, UAE”
Important Note:
This design report shall be read along with submitted design drawings
KEY PLAN
Page 4 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
The steel structural drawings has been created based with respect to the below listed
drawings/documents for this project.
Page 5 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 6 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
- This structure has been designed to withstand all the relavent actions according to american Standards, taking into
account available local data.
- The major loading on the structure are gravity loads such as superimposed dead loads as well as imposed loads on
floors.
DESIGN LOADS
S.N. ITEM UNITS LOAD VALUE
kN/m2 1. Own weight of the structural elements will be calculated automatically
1 Dead Load by design software.
2. Finishing & service load shall be followed as per loading plan.
2 Live Load – Purlin kN/m2 As per loading plan
3 Collateral Load kN/m2 As per loading plan
1. (3 sec Gust Wind Speed) = 162 Km/hr
2. Importance Factor = 1.15
4 Wind load
3. Exposure-‘C’
4. Occupancy category III
1. Occupancy category III
2. Importance Factor = 1.25
3. Ss = 0.80
5 Seismic load
4. S1 = 0.24
5. Site class = C
6. R = 3.50
6 Temperature load ±25 centigrade
o
Important Note:
For more information about applied design loads & loading location refer to Loading plan
drawings as indicated in the design drawings index sheet.
DESIGN CODE
1 Built-up & Hot rolled Sections American Institute of Steel Construction AISC-360-10
2 Cold Formed Sections American Iron and Steel Institute AISI 2002
3 Welding American Welding Society AWS D1.1/ D1.1M 2015
BUILDING CODE
Building Code ASCE 7-05
Page 7 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
- For the below loading calculation reference taken from project reference documents as mensiond in this report.
- Own weight of the structural elements will be calculated automatically by design software
- Finishing & service load shall be followed as per loading plan.
Page 8 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 9 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 10 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
For the below loading calculation reference taken from project reference documents as mensiond in this report.
Sesimic load has been calculated as per the given parameters as follow, so that seismic load will be
Base shear value will be calculated automatically by STAAD software, and will be reported in the design
output based on the below parameters.
Page 11 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 12 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
LRFD Combinations:
Page 13 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
Page 14 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 15 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
The below material table is showing the structural steel material specifications used in this
project.
Page 16 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 17 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Floor Dead Load has been applied as per design load schedule (Supermarket sample)
Floor Live Load has been applied as per design load schedule (Supermarket sample)
Page 18 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 19 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 20 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 21 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 22 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 23 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
- Steel joist design has been perfomed using ETABS20, Please refer to the attached Appendix-1
Page 24 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Project data
Project name PROPOSED G+M+R COMMERCIAL BUILDING
Project number AE3-3238
Author MABANI STEEL
Description Base Plate connections
Date 21/06/2023
Code AISC/ACI
Material
Steel A572 Gr.50
Concrete 4000 psi, 4500 psi, 5000 psi
Members
Geometry
X
Name Support Forces in
[mm]
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Cross-sections
Name Material
138 - I528 A572 Gr.50
137 - I728 A572 Gr.50
Bolts
Page 26 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 231.0 2.0 -335.0 0.0 818.0 3.0
LE3 B / End 378.0 3.0 -427.0 0.0 609.0 1.0
LE4 B / End 317.0 -15.0 -285.0 0.0 551.0 -24.0
LE5 B / End 321.0 -1.0 -435.0 0.0 648.0 0.0
LE6 B / End 269.0 22.0 -317.0 0.0 472.0 9.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Page 27 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 28 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 29 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Bolts
Design data
Page 30 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
[kN] [kN]
30 A325M - 1 328.8 197.3
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
413.8 kN ≥ 7.2 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
EP1 B-bfl 1 E70xx - - 250 - - - - - OK
Page 31 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 32 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
B-w 1 RIB2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 149 10 LE3 1.7 10.4 16.1 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 149 10 LE4 2.7 9.8 27.4 OK
EP1 RIB5 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 134 12 LE1 15.1 16.1 94.2 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 134 12 LE1 15.1 16.1 94.0 OK
B-tfl 1 RIB5 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 198 12 LE1 10.8 14.2 75.7 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 198 12 LE1 10.8 14.2 75.6 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Page 33 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
CUT1
Welds
Bolts
Grip length
Name Count
[mm]
30 A325M 38 14
Page 34 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Drawing
EP1
STIFF1
Page 35 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
WID1
Page 36 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB1
Page 37 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB2
Page 38 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB5
Page 39 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Members
Geometry
X
Name Support Forces in
[mm]
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Page 40 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Cross-sections
Name Material
161 - I532 A572 Gr.50
160 - I800 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 379.0 0.0 -389.0 0.0 886.0 1.0
LE3 B / End -278.0 3.0 -640.0 0.0 1511.0 2.0
LE4 B / End -12.0 2.0 -422.0 0.0 732.0 5.0
LE5 B / End -187.0 -112.0 -620.0 0.0 1322.0 -152.0
LE7 B / End 263.0 5.0 -401.0 0.0 382.0 4.0
LE8 B / End -27.0 6.0 -72.0 0.0 565.0 6.0
LE9 B / End -177.0 93.0 -597.0 0.0 1475.0 105.0
Page 41 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Page 42 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 43 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 44 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Bolts
Design data
Page 45 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
[kN] [kN]
36 A325M - 1 473.4 284.0
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
726.0 kN ≥ 22.7 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
EP1 B-bfl 1 E70xx - - 375 - - - - - OK
Page 46 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
Page 47 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
CUT1
Page 48 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 50 14
Page 49 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Drawing
EP1
STIFF1
Page 50 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
WID1
Page 51 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB1
Page 52 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB2
Page 53 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB5
Page 54 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Members
Geometry
X
Name Support Forces in
[mm]
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Page 55 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Cross-sections
Name Material
163 - I528 A572 Gr.50
162 - I870 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End -187.0 -112.0 -620.0 0.0 1322.0 -152.0
Page 56 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Page 57 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 58 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 59 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Bolts
Design data
Page 60 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
[kN] [kN]
36 A325M - 1 473.4 284.0
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
630.4 kN ≥ 30.1 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
EP1 B-bfl 1 E70xx - - 450 - - - - - OK
Page 61 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
Page 62 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
CUT1
Page 63 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 55 14
Page 64 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Drawing
EP1
STIFF1
Page 65 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
WID1
Page 66 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB1
Page 67 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB2
Page 68 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB5
Page 69 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Page 70 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Cross-sections
Name Material
165 - I580 A572 Gr.50
164 - I1100 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE10 B / End -638.0 -70.0 -1417.0 0.0 6453.0 -1.0
Page 71 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Page 72 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 73 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 74 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Bolts
Page 75 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Design data
ϕRn,tension ϕRn,shear
Grade
[kN] [kN]
36 A325M - 1 473.4 284.0
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Page 76 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
1355.2 kN ≥ 53.9 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
EP1 B-bfl 1 E70xx - - 550 - - - - - OK
EP1 B-tfl 1 E70xx - - 550 - - - - - OK
EP1 B-w 1 E70xx - - 1050 - - - - - OK
C-bfl 1 STIFF1a E70xx - - 295 - - - - - OK
C-w 1 STIFF1a E70xx - - 460 - - - - - OK
C-tfl 1 STIFF1a E70xx - - 295 - - - - - OK
C-bfl 1 STIFF1b E70xx - - 295 - - - - - OK
C-w 1 STIFF1b E70xx - - 460 - - - - - OK
C-tfl 1 STIFF1b E70xx - - 295 - - - - - OK
C-bfl 1 STIFF1c E70xx - - 295 - - - - - OK
C-w 1 STIFF1c E70xx - - 460 - - - - - OK
C-tfl 1 STIFF1c E70xx - - 295 - - - - - OK
C-bfl 1 STIFF1d E70xx - - 295 - - - - - OK
C-w 1 STIFF1d E70xx - - 460 - - - - - OK
C-tfl 1 STIFF1d E70xx - - 295 - - - - - OK
EP1 WID1 E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 23.8 30.3 78.6 OK
E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 23.8 30.3 78.6 OK
B-bfl 1 WID1 E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 25.3 30.6 82.9 OK
E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 25.3 30.6 82.9 OK
EP1 RIB1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 9.7 20.0 48.2 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 7.2 21.0 34.5 OK
B-w 1 RIB1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 299 19 LE10 11.5 20.5 56.0 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 299 19 LE10 11.6 20.6 56.3 OK
EP1 RIB1b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 6.9 23.5 29.4 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 9.9 21.7 45.5 OK
B-w 1 RIB1b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 299 19 LE10 11.4 20.6 55.5 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 299 19 LE10 11.1 20.5 54.1 OK
Page 77 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
EP1 RIB2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 3.1 21.8 14.3 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 3.1 18.3 17.0 OK
B-w 1 RIB2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 3.1 19.8 15.7 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 299 19 LE10 3.3 21.3 15.6 OK
EP1 RIB2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 3.0 19.4 15.5 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 3.1 21.9 14.3 OK
B-w 1 RIB2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 299 19 LE10 3.1 21.2 14.7 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 298 19 LE10 2.9 20.4 14.3 OK
EP1 RIB5 E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 24.6 30.0 82.0 OK
E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 24.6 30.0 82.0 OK
B-tfl 1 RIB5 E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 25.0 30.7 81.6 OK
E70xx ◢ 8.5 ◣ ◢ 12.0 ◣ 198 12 LE10 25.0 30.7 81.6 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Page 78 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Welds
Page 79 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Bolts
Grip length
Name Count
[mm]
36 A325M 120 36
Drawing
EP1
Page 80 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
STIFF1
Page 81 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
WID1
Page 82 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB1
Page 83 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB2
Page 84 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB5
Page 85 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Members
Geometry
X
Name Support Forces in
[mm]
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Page 86 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Cross-sections
Name Material
168 - I540 A572 Gr.50
167 - I632 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 247.0 10.0 -220.0 0.0 570.0 5.0
LE3 B / End -545.0 7.0 -65.0 0.0 114.0 1.0
LE4 B / End -11.0 1.0 -442.0 0.0 996.0 0.0
LE5 B / End 87.0 -11.0 -293.0 0.0 108.0 -10.0
LE6 B / End 238.0 10.0 -177.0 0.0 562.0 5.0
LE7 B / End 52.0 -13.0 -252.0 0.0 347.0 -9.0
LE8 B / End 37.0 -7.0 -330.0 1.0 689.0 -1.0
Page 87 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Page 88 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 89 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 90 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Bolts
Design data
ϕRn,tension ϕRn,shear
Grade
[kN] [kN]
30 A325M - 1 328.8 197.3
Page 91 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
440.5 kN ≥ 2.0 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
EP1 B-bfl 1 E70xx - - 250 - - - - - OK
EP1 B-tfl 1 E70xx - - 250 - - - - - OK
EP1 B-w 1 E70xx - - 616 - - - - - OK
C-bfl 1 STIFF1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 140 47 LE11 16.4 64.0 25.6 OK
Page 92 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Page 93 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
CUT1
Page 94 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Welds
Bolts
Grip length
Name Count
[mm]
30 A325M 40 10
Page 95 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Drawing
EP1
STIFF1
Page 96 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
WID1
Page 97 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB1
Page 98 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB2
Page 99 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
RIB5
Members
Geometry
X
Name Support Forces in
[mm]
COL / end Node 0
Cross-sections
Name Material
2 - I870 A572 Gr.50
Anchors
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 COL / End -9012.0 431.0 1524.0 0.0 -696.0 12.0
LE2 COL / End -9164.0 -422.0 1516.0 0.0 -680.0 -13.0
LE3 COL / End -10384.0 -106.0 754.0 0.0 -335.0 -1.0
LE4 COL / End -8924.0 -14.0 1671.0 0.0 -485.0 -11.0
LE5 COL / End -9164.0 -422.0 1516.0 0.0 -680.0 -13.0
LE6 COL / End -9698.0 219.0 1014.0 0.0 -1318.0 0.0
Foundation block
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Anchors
Design data
ϕNsa ϕVsa
Grade
[kN] [kN]
30 A325M - 1 325.9 145.3
Where:
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Where:
– resistance factor
– modification factor for concrete condition
– basic concrete pullout strength for headed anchor:
, where:
Where:
– reduction factor for steel strength in shear in case of mortar joint
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 COL-bfl 1 E70xx - - 650 - - - - - OK
BP1 COL-tfl 1 E70xx - - 650 - - - - - OK
BP1 COL-w 1 E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 808 51 LE5 74.7 99.3 75.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 808 51 LE5 75.4 100.2 75.2 OK
BP1 WID1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 99 12 LE3 21.2 27.9 75.8 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 12 LE3 21.2 28.1 75.2 OK
COL-bfl 1 WID1a E70xx - - 250 - - - - - OK
BP1 WID1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 12 LE3 21.0 27.9 75.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 99 12 LE3 21.1 27.9 75.8 OK
COL-bfl 1 WID1b E70xx - - 250 - - - - - OK
BP1 WID1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 99 12 LE6 22.4 28.1 79.9 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 99 12 LE6 22.3 28.0 79.6 OK
COL-tfl 1 WID1c E70xx - - 250 - - - - - OK
BP1 WID1d E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 99 12 LE6 22.3 28.0 79.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 99 12 LE6 22.3 28.0 79.6 OK
COL-tfl 1 WID1d E70xx - - 250 - - - - - OK
BP1 RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE3 25.4 38.1 66.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE3 18.1 37.2 48.8 OK
COL-w 1 RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE3 33.4 43.4 76.9 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE3 33.9 43.9 77.1 OK
Page 108 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
BP1 RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE6 24.4 39.0 62.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE3 22.7 38.5 59.1 OK
COL-w 1 RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE6 33.9 43.5 77.9 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE6 34.1 43.8 78.0 OK
BP1 RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE3 17.9 37.2 48.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE3 25.0 38.2 65.4 OK
COL-w 1 RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE3 33.9 43.9 77.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE3 33.4 43.4 76.9 OK
BP1 RIB1d E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE3 22.7 36.9 61.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 398 20 LE6 24.1 38.0 63.3 OK
COL-w 1 RIB1d E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE6 34.1 43.7 78.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 21 LE6 33.9 43.5 77.9 OK
BP1 RIB2a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE6 22.5 27.1 83.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE6 21.9 26.8 81.7 OK
COL-tfl 1 RIB2a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE5 16.1 21.7 74.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE5 16.2 21.6 75.0 OK
BP1 RIB2b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE6 21.9 26.8 81.9 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE6 22.5 27.1 83.3 OK
COL-tfl 1 RIB2b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE1 16.3 21.7 75.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE6 18.0 24.0 75.0 OK
BP1 RIB3a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE3 17.4 26.8 64.8 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE3 19.3 25.7 75.0 OK
COL-bfl 1 RIB3a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 10.1 23.3 43.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 9.6 23.7 40.5 OK
BP1 RIB3b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE3 19.2 25.6 75.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 159 12 LE3 17.1 26.7 63.9 OK
COL-bfl 1 RIB3b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 9.5 23.7 40.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 10.1 23.3 43.2 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Concrete block
A1 A2 σ ϕfp,max Ut
Item Loads Status
[mm2] [mm2] [MPa] [MPa] [%]
CB 1 LE3 983342 1454654 10.6 18.5 57.0 OK
Where:
– concrete block design bearing strength:
, where:
Buckling
Bill of material
Manufacturing operations
Welds
Anchors
Drawing
BP1
WID1
RIB1
RIB2
RIB3
Members
Geometry
X
Name Support Forces in
[mm]
COL / end Node 0
Cross-sections
Name Material
3 - I540 A572 Gr.50
Anchors
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Foundation block
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
Anchors
Design data
ϕNsa ϕVsa
Grade
[kN] [kN]
30 A325M - 1 325.9 145.3
Where:
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Where:
– resistance factor
– modification factor for concrete condition
– basic concrete pullout strength for headed anchor:
, where:
Where:
– reduction factor for steel strength in shear in case of mortar joint
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Where:
– maximum ratio of factored tensile force and tensile resistance determined from all appropriate
failure modes
– maximum ratio of factored shear force and shear resistance determined from all appropriate
failure modes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 COL-bfl 1 E70xx - - 400 - - - - - OK
BP1 COL-tfl 1 E70xx - - 400 - - - - - OK
BP1 COL-w 1 E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 513 29 LE3 48.1 63.0 76.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 513 29 LE3 48.1 63.0 76.4 OK
BP1 RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE6 13.0 25.1 51.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE6 14.2 25.7 55.3 OK
COL-w 1 RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE1 16.1 21.4 75.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE1 16.1 21.4 75.3 OK
BP1 RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 13.6 23.3 58.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE5 12.3 26.5 46.6 OK
COL-w 1 RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE2 16.1 21.4 75.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE2 16.1 21.4 75.3 OK
BP1 RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE6 14.0 25.2 55.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE6 13.0 25.7 50.5 OK
COL-w 1 RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE1 16.1 21.4 75.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE1 16.1 21.4 75.3 OK
BP1 RIB1d E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 12.8 27.2 47.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 248 12 LE3 13.8 26.3 52.5 OK
COL-w 1 RIB1d E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE2 16.1 21.4 75.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 249 12 LE2 16.1 21.4 75.3 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Concrete block
A1 A2 σ ϕfp,max Ut
Item Loads Status
[mm2] [mm2] [MPa] [MPa] [%]
CB 1 LE3 230369 999270 27.5 30.5 90.2 OK
Where:
– concrete block design bearing strength:
, where:
Buckling
Bill of material
Manufacturing operations
Welds
Anchors
Drawing
BP1
RIB1
Members
Geometry
X
Name Support Forces in
[mm]
COL / end Node 0
Cross-sections
Name Material
4 - I500X20/400X40(I580) A572 Gr.50
Anchors
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Foundation block
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Anchors
Design data
ϕNsa ϕVsa
Grade
[kN] [kN]
30 A325M - 1 325.9 145.3
325.9 kN ≥ 269.6 kN
Where:
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Where:
– resistance factor
– modification factor for concrete condition
– basic concrete pullout strength for headed anchor:
, where:
Where:
– reduction factor for anchor close to an edge or multiple anchors with small spacing:
, where:
, where:
Where:
– reduction factor for steel strength in shear in case of mortar joint
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 COL-bfl 1 E70xx - - 400 - - - - - OK
BP1 COL-tfl 1 E70xx - - 400 - - - - - OK
BP1 COL-w 1 E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 539 41 LE2 67.8 91.5 74.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 539 41 LE3 67.3 89.7 75.0 OK
BP1 WID1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 60 12 LE3 20.6 27.4 75.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 60 12 LE3 19.6 26.0 75.2 OK
COL-bfl 1 WID1a E70xx - - 250 - - - - - OK
BP1 WID1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 60 12 LE2 18.5 24.5 75.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 60 12 LE2 20.7 27.5 75.2 OK
Page 133 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Concrete block
A1 A2 σ ϕfp,max Ut
Item Loads Status
[mm2] [mm2] [MPa] [MPa] [%]
CB 1 LE2 143008 357603 11.3 24.1 47.0 OK
Where:
– concrete block design bearing strength:
, where:
Buckling
Bill of material
Manufacturing operations
Welds
Anchors
[mm] [mm]
30 A325M 830 750 8
Drawing
BP1
WID1
RIB1
RIB2
RIB3
Material
Steel A572 Gr.50, A36, A572 Gr.42
Concrete 4000 psi
Members
Geometry
X
Name Support Forces in
[mm]
B1 / end Node 0
B2 / end N-Vy-Vz-Mx-My-Mz Node 0
Cross-sections
Name Material
117 - I600X6/225*12(I624) A572 Gr.50
139 - I636 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B1 / End 567.0 7.0 -255.0 0.0 339.0 14.0
LE2 B1 / End 137.0 -1.0 -69.0 0.0 90.0 -2.0
LE3 B1 / End 565.0 7.0 -263.0 0.0 373.0 15.0
LE4 B1 / End 420.0 -1.0 -249.0 0.0 226.0 -1.0
LE5 B1 / End 371.0 10.0 -79.0 0.0 253.0 5.0
LE6 B1 / End 377.0 -1.0 -223.0 0.0 329.0 -4.0
LE7 B1 / End 520.0 6.0 -248.0 0.0 309.0 12.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Bolts
Design data
[kN] [kN]
24 A325M - 1 210.2 126.1
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
271.0 kN ≥ 12.8 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
PP1a B1-bfl 1 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE11 60.2 76.7 78.5 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE11 61.6 77.0 80.0 OK
PP1a B1-tfl 1 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE9 58.4 74.8 78.1 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE11 60.4 77.6 77.8 OK
PP1a B1-w 1 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 611 51 LE12 57.5 70.1 82.0 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 611 51 LE12 57.3 70.1 81.8 OK
PP1b B2-bfl 1 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE11 62.9 77.7 80.9 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE11 62.0 77.7 79.8 OK
PP1b B2-tfl 1 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE12 59.1 77.6 76.1 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 225 56 LE11 59.6 77.7 76.7 OK
PP1b B2-w 1 E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 617 51 LE11 60.0 69.7 86.0 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 617 51 LE12 59.9 70.0 85.6 OK
PP1a WID1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 11.5 13.0 88.5 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE11 11.7 13.2 89.0 OK
B1-tfl 1 WID1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 10.9 12.3 88.5 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 10.9 12.3 88.5 OK
PP1a WID1b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE9 10.3 13.5 76.4 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE9 10.0 13.3 75.5 OK
B1-bfl 1 WID1b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 9.5 12.2 77.6 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 9.5 12.2 77.6 OK
PP1b WID2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE8 11.3 13.1 86.2 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 11.4 13.1 87.3 OK
B2-tfl 1 WID2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 10.4 12.4 84.0 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 10.4 12.4 84.0 OK
PP1b WID2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE9 10.3 13.6 75.4 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE9 10.4 13.6 76.4 OK
B2-bfl 1 WID2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 9.2 12.1 75.5 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 129 10 LE12 9.2 12.1 75.5 OK
PP1a RIB1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE12 4.8 10.4 46.2 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE11 3.7 12.1 30.2 OK
B1-w 1 RIB1a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 4.3 10.8 39.6 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 4.3 10.8 40.0 OK
PP1a RIB1b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE12 9.2 12.2 75.2 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE12 6.9 12.2 56.6 OK
B1-w 1 RIB1b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE11 8.4 11.2 75.1 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 8.4 11.2 75.1 OK
PP1a RIB1c E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE9 3.0 12.0 24.8 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE11 5.2 11.5 45.2 OK
B1-w 1 RIB1c E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 4.3 10.9 39.4 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 4.2 10.9 38.4 OK
PP1a RIB1d E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE12 8.6 12.5 68.9 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 99 10 LE12 9.4 12.5 75.1 OK
B1-w 1 RIB1d E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 8.3 11.0 75.1 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 100 10 LE12 8.2 11.0 75.1 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
24 A325M 28 14
Drawing
PP1 - PP1a
PP1 - PP1b
WID1
WID2
RIB1
RIB2
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
M3 / end Node 0
Cross-sections
Name Material
121 - I536 A572 Gr.50
120 - RHS450/250/10.0 A572 Gr.50
122 - SHS200/200/8.0 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 177.0 -1.0 -57.0 48.0 64.0 -10.0
M3 / End 495.0 0.0 -3.0 0.0 0.0 0.0
LE2 B / End -390.0 10.0 -18.0 1.0 59.0 25.0
M3 / End 495.0 0.0 -3.0 0.0 0.0 0.0
LE3 B / End -160.0 2.0 -91.0 -2.0 153.0 5.0
Page 157 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
A36 248.2 5.0
Bolts
Design data
ϕRn,tension ϕRn,shear
Grade
[kN] [kN]
20 A325M - 1 146.0 87.6
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
253.8 kN ≥ 2.6 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-bfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 171 57 LE3 92.9 144.1 64.5 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
20 A325M 28 6
24 A325M 30 4
Drawing
STUB1 - STUB1-EPa
STUB1 - STUB1-EPb
STIFF1
P16.0x500-171 (A36)
STUB2 - STUB2-EPa
STUB2 - STUB2-EPb
RIB5
RIB6
RIB7
RIB8
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
M3 / end Node 0
M4 / end Node 0
Cross-sections
Name Material
120 - RHS450/250/10.0 A572 Gr.50
122 - SHS200/200/8.0 A572 Gr.50
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 850.0 0.0 0.0 0.0 0.0 0.0
M3 / End -750.0 0.0 0.0 0.0 0.0 0.0
M4 / End -750.0 0.0 0.0 0.0 0.0 0.0
LE2 B / End -750.0 0.0 0.0 0.0 0.0 0.0
M3 / End 850.0 0.0 0.0 0.0 0.0 0.0
M4 / End 850.0 0.0 0.0 0.0 0.0 0.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-w 1 M3-arc 2 E70xx - - 1 - - - - - OK
C-w 1 M3-arc 11 E70xx - - 1 - - - - - OK
C-w 1 M4-arc 2 E70xx - - 1 - - - - - OK
C-w 1 M3-arc 3 E70xx - - 12 - - - - - OK
C-w 1 M3-w 2 E70xx - - 226 - - - - - OK
C-w 1 M3-arc 4 E70xx - - 12 - - - - - OK
C-w 1 M3-arc 5 E70xx - - 10 - - - - - OK
C-w 1 M3-arc 6 E70xx - - 9 - - - - - OK
C-w 1 M3-w 3 E70xx - - 160 - - - - - OK
C-w 1 M3-arc 7 E70xx - - 9 - - - - - OK
C-w 1 M3-arc 8 E70xx - - 10 - - - - - OK
C-w 1 M3-arc 9 E70xx - - 12 - - - - - OK
C-w 1 M3-w 4 E70xx - - 226 - - - - - OK
C-w 1 M3-arc 10 E70xx - - 12 - - - - - OK
C-w 1 M4-arc 11 E70xx - - 1 - - - - - OK
C-w 1 M4-arc 3 E70xx - - 12 - - - - - OK
C-w 1 M4-w 2 E70xx - - 226 - - - - - OK
C-w 1 M4-arc 4 E70xx - - 12 - - - - - OK
C-w 1 M4-arc 5 E70xx - - 10 - - - - - OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
M3 / end Node 0
Cross-sections
Name Material
128 - I700 A572 Gr.50
127 - RHS450/250/16.0 A572 Gr.50
130 - SHS200/200/6.3 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 2469.0 20.0 -110.0 0.0 0.0 0.0
M3 / End -554.0 0.0 0.0 0.0 0.0 0.0
LE2 B / End -2015.0 33.0 -105.0 0.0 0.0 0.0
M3 / End 564.0 0.0 0.0 0.0 0.0 0.0
LE3 B / End -762.0 42.0 394.0 0.0 0.0 0.0
Page 181 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
A36 248.2 5.0
Bolts
Design data
[kN] [kN]
36 A325M - 1 473.4 284.0
24 A325M - 2 210.2 126.1
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
220.8 kN ≥ 3.1 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
Page 186 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
C-bfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 38.3 115.0 33.3 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 21.8 117.0 18.6 OK
C-w 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 20.1 124.2 16.2 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 20.7 109.4 18.9 OK
C-tfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 14.3 114.0 12.6 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 13.7 120.2 11.4 OK
C-bfl 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 20.9 117.2 17.8 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 33.7 103.4 32.6 OK
C-w 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 19.1 110.8 17.2 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 19.1 124.9 15.3 OK
C-tfl 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 13.8 120.2 11.5 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 14.3 114.9 12.4 OK
C-bfl 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 30.2 116.5 25.9 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 49.3 113.3 43.5 OK
C-w 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 21.6 105.6 20.4 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 21.2 120.2 17.6 OK
C-tfl 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 13.7 119.5 11.5 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 14.4 114.1 12.6 OK
C-bfl 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 47.8 112.9 42.3 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 31.0 117.7 26.3 OK
C-w 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 20.4 120.5 16.9 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE1 20.4 106.3 19.2 OK
C-tfl 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 14.4 114.7 12.5 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE1 13.8 119.7 11.5 OK
STUB1-EPa RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.4 45.3 76.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.4 44.5 77.4 OK
B-w 2 RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 23.5 31.1 75.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 16.0 39.3 40.7 OK
STUB1-EPa RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.6 45.1 76.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.4 45.7 75.3 OK
B-w 2 RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 23.5 40.3 58.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 22.0 41.5 53.1 OK
STUB1-EPa RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.6 45.5 76.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.2 45.4 75.4 OK
B-w 2 RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 17.5 40.9 42.8 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 23.3 31.0 75.2 OK
STUB1-EPa RIB2a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.1 45.1 75.6 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.7 45.7 75.8 OK
B-w 4 RIB2a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 23.6 31.4 75.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 16.1 30.0 53.6 OK
STUB1-EPa RIB2b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.4 45.6 75.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.7 45.7 76.0 OK
B-w 4 RIB2b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 20.6 41.5 49.6 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 22.3 40.1 55.5 OK
STUB1-EPa RIB2c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.3 45.5 75.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.6 45.6 75.8 OK
B-w 4 RIB2c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 14.5 30.3 47.9 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 23.5 31.2 75.3 OK
STUB1-EPb RIB3a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.8 45.7 76.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 35.9 45.8 78.2 OK
STUB1-w 2 RIB3a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE1 20.2 40.4 50.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE1 24.9 33.1 75.2 OK
STUB1-EPb RIB3b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 35.9 45.8 78.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 36.3 45.8 79.2 OK
STUB1-w 2 RIB3b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 27.4 40.5 67.6 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 28.2 39.9 70.6 OK
STUB1-EPb RIB3c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 39.5 45.8 86.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 39.3 45.8 85.9 OK
STUB1-w 2 RIB3c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 26.1 34.8 75.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE1 22.9 30.3 75.7 OK
STUB1-EPb RIB4a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.5 45.5 75.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.4 45.6 75.3 OK
STUB1-w 4 RIB4a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 23.5 31.3 75.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 22.6 33.5 67.3 OK
STUB1-EPb RIB4b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.7 45.6 76.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.4 45.6 75.4 OK
STUB1-w 4 RIB4b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 22.2 40.8 54.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 21.8 41.1 52.9 OK
STUB1-EPb RIB4c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.7 45.8 75.6 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 34.2 45.3 75.5 OK
STUB1-w 4 RIB4c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 22.8 36.7 62.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE1 19.6 31.7 61.9 OK
STUB2-EPa M3-w 1 E70xx - - 169 - - - - - OK
STUB2-EPa M3-arc 1 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 2 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 3 E70xx - - 7 - - - - - OK
STUB2-EPa M3-w 2 E70xx - - 169 - - - - - OK
STUB2-EPa M3-arc 4 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 5 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 6 E70xx - - 7 - - - - - OK
STUB2-EPa M3-w 3 E70xx - - 169 - - - - - OK
STUB2-EPa M3-arc 7 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 8 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 9 E70xx - - 7 - - - - - OK
STUB2-EPa M3-w 4 E70xx - - 169 - - - - - OK
STUB2-EPa M3-arc 10 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 11 E70xx - - 7 - - - - - OK
STUB2-EPa M3-arc 12 E70xx - - 7 - - - - - OK
STUB2-EPb STUB2-w 1 E70xx - - 169 - - - - - OK
STUB2-EPb STUB2-arc 1 E70xx - - 7 - - - - - OK
STUB2-w 4 RIB8 E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE4 8.6 10.1 85.8 OK
E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE4 8.3 9.8 84.4 OK
STUB1-EPa B E70xx ◢ 15.6 ◢ 22.0 1277 17 LE1 51.8 56.0 92.5 OK
STUB1-EPb STUB1 E70xx ◢ 15.6 ◢ 22.0 1277 17 LE1 48.1 56.0 86.0 OK
C-bfl 1 STUB1 E70xx ◢ 15.6 ◢ 22.0 1277 17 LE1 43.8 56.0 78.3 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 40 8
24 A325M 30 4
Drawing
STUB1 - STUB1-EPa
STUB1 - STUB1-EPb
STIFF1
P16.0x600-237 (A36)
RIB1
RIB2
RIB3
RIB4
STUB2 - STUB2-EPa
STUB2 - STUB2-EPb
RIB5
RIB6
RIB7
RIB8
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Cross-sections
Name Material
128 - I700 A572 Gr.50
129 - RHS450/250/10.0 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 475.0 20.0 -110.0 0.0 0.0 0.0
LE2 B / End -2015.0 33.0 -105.0 0.0 0.0 0.0
LE3 B / End -762.0 42.0 394.0 0.0 0.0 0.0
LE4 B / End -704.0 -47.0 -413.0 0.0 0.0 0.0
LE5 B / End -425.0 128.0 26.0 0.0 0.0 0.0
LE6 B / End 15.0 -131.0 -23.0 0.0 0.0 0.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
A36 248.2 5.0
Bolts
Design data
ϕRn,tension ϕRn,shear
Grade
[kN] [kN]
36 A325M - 1 473.4 284.0
473.4 kN ≥ 312.3 kN
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
328.7 kN ≥ 48.2 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-bfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 35.4 112.0 31.6 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE3 21.6 115.6 18.7 OK
C-w 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 15.8 122.7 12.9 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 16.6 107.3 15.4 OK
C-tfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 13.8 115.0 12.0 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 13.4 120.2 11.1 OK
C-bfl 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 25.3 114.3 22.1 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 43.7 110.0 39.7 OK
C-w 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 19.3 106.0 18.3 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 17.8 121.9 14.6 OK
C-tfl 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 13.2 120.0 11.0 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 14.0 113.4 12.3 OK
C-bfl 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 26.4 117.3 22.5 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 45.3 111.0 40.8 OK
C-w 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 18.9 104.6 18.1 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 18.3 120.4 15.2 OK
C-tfl 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 13.5 120.0 11.2 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 14.0 114.5 12.3 OK
C-bfl 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 50.8 109.7 46.3 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 29.8 115.8 25.7 OK
C-w 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 19.5 120.2 16.2 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 20.8 103.9 20.0 OK
C-tfl 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 14.1 113.6 12.4 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 13.3 119.7 11.1 OK
STUB1-EPa RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 34.6 45.9 75.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 29.8 44.3 67.2 OK
B-w 2 RIB1a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 19.9 32.8 60.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 16.8 41.8 40.2 OK
STUB1-EPa RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 13.7 45.8 29.9 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 12.2 36.3 33.6 OK
B-w 2 RIB1b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 7.7 32.2 24.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE4 7.2 28.7 25.2 OK
STUB1-EPa RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 34.0 45.2 75.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 35.0 46.0 76.1 OK
B-w 2 RIB1c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE4 21.0 40.4 52.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE4 23.2 33.2 70.0 OK
STUB1-EPa RIB2a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 34.5 45.9 75.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 23.6 43.8 53.9 OK
B-w 4 RIB2a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE4 16.5 32.5 50.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 11.4 34.9 32.7 OK
STUB1-EPa RIB2b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 11.8 42.1 28.1 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 13.0 36.9 35.3 OK
B-w 4 RIB2b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 10.7 33.1 32.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 10.9 32.7 33.4 OK
STUB1-EPa RIB2c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 34.0 45.1 75.3 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 34.9 46.0 76.0 OK
B-w 4 RIB2c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 20.7 40.0 51.8 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 24.0 33.6 71.4 OK
STUB1-EPb RIB3a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 34.8 45.8 76.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 34.1 45.4 75.1 OK
STUB1-w 2 RIB3a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE4 18.4 35.7 51.5 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE4 18.9 35.2 53.8 OK
STUB1-EPb RIB3b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 17.6 45.7 38.6 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 18.4 45.8 40.2 OK
STUB1-w 2 RIB3b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 8.1 32.6 24.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE1 10.2 34.3 29.7 OK
STUB1-EPb RIB3c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE1 23.0 44.8 51.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 34.5 45.9 75.3 OK
STUB1-w 2 RIB3c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE1 14.5 33.4 43.4 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 12.9 34.0 37.9 OK
STUB1-EPb RIB4a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 34.5 45.7 75.6 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 34.3 45.6 75.2 OK
STUB1-w 4 RIB4a E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 21.4 37.7 56.7 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE3 20.2 35.5 57.0 OK
STUB1-EPb RIB4b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 16.1 38.3 42.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 13.5 41.3 32.7 OK
STUB1-w 4 RIB4b E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 298 19 LE4 8.8 29.1 30.2 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 10.0 33.3 30.0 OK
STUB1-EPb RIB4c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE3 20.8 44.5 46.8 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 100 20 LE4 32.3 45.7 70.8 OK
STUB1-w 4 RIB4c E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE2 11.1 33.5 33.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 299 19 LE4 12.6 36.1 34.8 OK
STUB1-EPa B E70xx ◢ 9.9 ◢ 14.0 1322 10 LE4 21.1 22.3 94.8 OK
STUB1-EPb STUB1 E70xx ◢ 9.9 ◢ 14.0 1321 28 LE4 55.3 61.2 90.4 OK
C-bfl 1 STUB1 E70xx ◢ 9.9 ◢ 14.0 1322 10 LE2 20.5 22.3 92.2 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 40 8
Drawing
STUB1 - STUB1-EPa
STUB1 - STUB1-EPb
STIFF1
P16.0x600-237 (A36)
RIB1
RIB2
RIB3
RIB4
Members
Geometry
X
Name Support Forces in
[mm]
Cross-sections
Name Material
146 - RHS450/250/12.5 A572 Gr.50
122 - SHS200/200/8.0 A572 Gr.50
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 732.0 0.0 0.0 0.0 0.0 0.0
M3 / End -732.0 0.0 0.0 0.0 0.0 0.0
M4 / End -732.0 0.0 0.0 0.0 0.0 0.0
LE2 B / End -732.0 0.0 0.0 0.0 0.0 0.0
M3 / End 732.0 0.0 0.0 0.0 0.0 0.0
M4 / End 732.0 0.0 0.0 0.0 0.0 0.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-w 1 B-w 1 E70xx - - 160 - - - - - OK
C-w 1 B-arc 1 E70xx - - 8 - - - - - OK
C-w 1 B-arc 2 E70xx - - 8 - - - - - OK
C-w 1 B-arc 3 E70xx - - 8 - - - - - OK
C-w 1 B-w 2 E70xx - - 160 - - - - - OK
C-w 1 B-arc 4 E70xx - - 8 - - - - - OK
C-w 1 B-arc 5 E70xx - - 8 - - - - - OK
C-w 1 B-arc 6 E70xx - - 8 - - - - - OK
C-w 1 B-w 3 E70xx - - 160 - - - - - OK
C-w 1 B-arc 7 E70xx - - 8 - - - - - OK
C-w 1 B-arc 8 E70xx - - 8 - - - - - OK
C-w 1 B-arc 9 E70xx - - 8 - - - - - OK
C-w 1 B-w 4 E70xx - - 160 - - - - - OK
C-w 1 B-arc 10 E70xx - - 8 - - - - - OK
C-w 1 B-arc 11 E70xx - - 8 - - - - - OK
C-w 1 B-arc 12 E70xx - - 8 - - - - - OK
C-w 1 M3-arc 2 E70xx - - 0 - - - - - OK
C-w 1 M3-arc 11 E70xx - - 0 - - - - - OK
C-w 1 M4-arc 2 E70xx - - 0 - - - - - OK
Butt welds are not checked. Their resistance is assumed to be the same as that of the welded
member.
Buckling
Bill of material
Manufacturing operations
Welds
Members
Geometry
X
Name Support Forces in
[mm]
B1 / end Node 0
B2 / end N-Vy-Vz-Mx-My-Mz Node 0
Cross-sections
Name Material
140 - I628 A572 Gr.50
141 - I640 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B1 / End -57.0 3.0 -231.0 0.0 454.0 1.0
LE4 B1 / End -63.0 3.0 -189.0 0.0 140.0 1.0
LE5 B1 / End -134.0 8.0 -488.0 0.0 990.0 9.0
LE6 B1 / End -63.0 0.0 -234.0 0.0 465.0 3.0
LE7 B1 / End -67.0 1.0 -224.0 0.0 422.0 2.0
LE9 B1 / End -61.0 2.0 -221.0 0.0 242.0 5.0
LE12 B1 / End -63.0 3.0 -189.0 0.0 140.0 1.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Bolts
Design data
[kN] [kN]
36 A325M - 1 473.4 284.0
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
492.1 kN ≥ 25.9 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
PP1a B1-bfl 1 E70xx - - 300 - - - - - OK
Page 231 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 40 14
Drawing
PP1 - PP1a
PP1 - PP1b
WID1
WID2
RIB1
RIB2
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Node 0
Cross-sections
Name Material
146 - RHS450/250/12.5 A572 Gr.50
122 - SHS200/200/8.0 A572 Gr.50
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 732.0 0.0 0.0 0.0 0.0 0.0
LE2 B / End -732.0 0.0 0.0 0.0 0.0 0.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-w 1 B-w 1 E70xx - - 160 - - - - - OK
C-w 1 B-arc 1 E70xx - - 8 - - - - - OK
C-w 1 B-arc 2 E70xx - - 8 - - - - - OK
C-w 1 B-arc 3 E70xx - - 8 - - - - - OK
C-w 1 B-w 2 E70xx - - 160 - - - - - OK
C-w 1 B-arc 4 E70xx - - 8 - - - - - OK
C-w 1 B-arc 5 E70xx - - 8 - - - - - OK
C-w 1 B-arc 6 E70xx - - 8 - - - - - OK
C-w 1 B-w 3 E70xx - - 160 - - - - - OK
C-w 1 B-arc 7 E70xx - - 8 - - - - - OK
C-w 1 B-arc 8 E70xx - - 8 - - - - - OK
C-w 1 B-arc 9 E70xx - - 8 - - - - - OK
C-w 1 B-w 4 E70xx - - 160 - - - - - OK
C-w 1 B-arc 10 E70xx - - 8 - - - - - OK
C-w 1 B-arc 11 E70xx - - 8 - - - - - OK
C-w 1 B-arc 12 E70xx - - 8 - - - - - OK
Butt welds are not checked. Their resistance is assumed to be the same as that of the welded
member.
Buckling
Bill of material
Manufacturing operations
Welds
Members
Geometry
X
Name Support Forces in
[mm]
B1 / end Node 0
B2 / end N-Vy-Vz-Mx-My-Mz Node 0
Cross-sections
Name Material
143 - I620 A572 Gr.50
142 - I640 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B1 / End 107.0 -1.0 -276.0 0.0 123.0 -1.0
Page 246 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Bolts
Design data
[kN] [kN]
30 A325M - 1 328.8 197.3
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
484.0 kN ≥ 26.5 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
PP1a B1-bfl 1 E70xx - - 250 - - - - - OK
Page 251 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
30 A325M 40 14
Drawing
PP1 - PP1a
PP1 - PP1b
WID1
WID2
RIB1
RIB2
Members
Geometry
X
Name Support Forces in
[mm]
C / begin N-Vy-Vz-Mx-My-Mz Node 0
C / end N-Vy-Vz-Mx-My-Mz Node 0
B / end Mx-My-Mz Node 0
M3 / end Mx-My-Mz Node 0
Cross-sections
Name Material
128 - I700 A572 Gr.50
144 - Iwn574x(400/400) A572 Gr.50
145 - SHS350/350/16.0 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B / End 86.0 6.0 -33.0 0.0 0.0 0.0
M3 / End -4950.0 0.0 0.0 0.0 0.0 0.0
LE2 B / End -2831.0 3.0 -149.0 0.0 0.0 0.0
M3 / End -4950.0 0.0 0.0 0.0 0.0 0.0
LE3 B / End -2215.0 8.0 169.0 0.0 0.0 0.0
M3 / End -4950.0 0.0 0.0 0.0 0.0 0.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
A36 248.2 5.0
Bolts
Design data
[kN] [kN]
36 A325M - 1 473.4 284.0
30 A325M - 2 328.8 197.3
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
580.8 kN ≥ 2.2 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
Page 265 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
STUB1-EPa B-tfl 1 E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE3 81.2 199.0 40.8 OK
E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE3 79.6 198.7 40.1 OK
STUB1-EPa B-bfl 1 E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE2 61.0 197.4 30.9 OK
E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE2 60.4 199.3 30.3 OK
STUB1-EPa B-w 1 E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 547 39 LE3 33.8 198.1 17.0 OK
E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 547 39 LE3 33.6 198.1 17.0 OK
STUB1-EPb STUB1-tfl 1 E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE3 81.4 199.4 40.8 OK
E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE3 83.7 199.0 42.0 OK
STUB1-EPb STUB1-bfl 1 E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE2 79.2 200.7 39.5 OK
E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 400 40 LE2 51.2 198.3 25.8 OK
STUB1-EPb STUB1-w 1 E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 547 39 LE3 32.2 192.7 16.7 OK
E70xx ◢ 15.6 ◣ ◢ 22.0 ◣ 547 39 LE3 32.2 192.8 16.7 OK
C-bfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 96.9 116.1 83.5 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 97.6 120.1 81.3 OK
C-w 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 52.1 99.4 52.4 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 50.6 122.7 41.2 OK
C-tfl 1 STIFF1a E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 35.7 119.2 30.0 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 37.4 118.7 31.5 OK
C-bfl 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 97.7 115.7 84.4 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 97.0 116.1 83.5 OK
C-w 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 50.5 122.9 41.1 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 53.0 99.5 53.2 OK
C-tfl 1 STIFF1b E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 37.3 118.6 31.4 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 35.5 119.2 29.8 OK
C-bfl 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE3 64.8 120.1 54.0 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 84.6 119.6 70.7 OK
C-w 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 56.4 120.8 46.7 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 45.0 124.6 36.1 OK
C-tfl 1 STIFF1c E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 82.4 118.9 69.3 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 44.4 117.1 37.9 OK
C-bfl 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 83.4 119.6 69.7 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE3 63.8 120.1 53.1 OK
C-w 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 44.9 124.6 36.0 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 599 50 LE2 56.3 120.9 46.5 OK
C-tfl 1 STIFF1d E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 44.4 117.2 37.9 OK
E70xx ◢ 7.8 ◣ ◢ 11.0 ◣ 237 47 LE2 82.4 118.9 69.3 OK
C-bfl 1 STUB1-tfl 1 E70xx - - 400 - - - - - OK
C-bfl 1 STUB1-bfl 1 E70xx - - 400 - - - - - OK
C-bfl 1 STUB2-w 2 E70xx - - 198 - - - - - OK
C-bfl 1 STUB1-w 1 E70xx - - 548 - - - - - OK
STUB2-EPa M3-w 1 E70xx - - 270 - - - - - OK
STUB2-EPa M3-arc 1 E70xx - - 17 - - - - - OK
STUB2-EPa M3-arc 2 E70xx - - 17 - - - - - OK
STUB2-EPa M3-arc 3 E70xx - - 17 - - - - - OK
STUB2-EPa M3-w 2 E70xx - - 270 - - - - - OK
M3-w 4 RIB6 E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE2 7.1 9.1 78.2 OK
E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE2 7.1 9.1 78.2 OK
STUB2-EPb RIB7 E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 99 10 LE2 7.9 11.4 69.6 OK
E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 99 10 LE2 7.2 11.4 63.4 OK
STUB2-w 2 RIB7 E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE2 7.5 9.7 76.7 OK
E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE2 7.5 9.8 76.8 OK
STUB2-EPb RIB8 E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 99 10 LE2 7.2 11.4 63.4 OK
E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 99 10 LE2 8.0 11.4 70.2 OK
STUB2-w 4 RIB8 E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE2 7.5 9.8 76.7 OK
E70xx ◢ 3.5 ◣ ◢ 5.0 ◣ 149 10 LE2 7.5 9.8 76.6 OK
STUB1-bfl 1 STIFF2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE2 54.7 67.7 80.8 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE2 51.3 67.2 76.3 OK
STUB1-w 1 STIFF2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 547 50 LE2 46.0 68.8 66.9 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 547 50 LE3 33.7 50.1 67.2 OK
STUB1-tfl 1 STIFF2a E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE2 24.7 52.5 47.0 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE3 26.0 49.1 53.0 OK
STUB1-bfl 1 STIFF2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE2 51.4 67.3 76.3 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE2 55.2 67.7 81.6 OK
STUB1-w 1 STIFF2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 547 50 LE3 33.0 50.2 65.9 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 547 50 LE2 45.6 68.8 66.3 OK
STUB1-tfl 1 STIFF2b E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE3 25.8 49.7 51.8 OK
E70xx ◢ 4.2 ◣ ◢ 6.0 ◣ 196 49 LE2 25.5 52.4 48.6 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 40 8
30 A325M 30 4
Drawing
STUB1 - STUB1-EPa
STUB1 - STUB1-EPb
STIFF1
P16.0x600-237 (A36)
STUB2 - STUB2-EPa
STUB2 - STUB2-EPb
RIB5
RIB6
RIB7
RIB8
STIFF2
Material
Steel A572 Gr.50, A36, A572 Gr.42
Concrete 4000 psi
Members
Geometry
X
Name Support Forces in
[mm]
B1 / end Node 0
B2 / end N-Vy-Vz-Mx-My-Mz Node 0
Cross-sections
Name Material
143 - I620 A572 Gr.50
142 - I640 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B1 / End 107.0 -1.0 -276.0 0.0 123.0 -1.0
LE2 B1 / End -24.0 1.0 -104.0 0.0 123.0 1.0
LE3 B1 / End 23.0 3.0 -69.0 0.0 147.0 1.0
LE4 B1 / End 87.0 1.0 -358.0 0.0 483.0 0.0
LE5 B1 / End 67.0 8.0 -295.0 0.0 160.0 3.0
LE6 B1 / End 36.0 -4.0 -110.0 0.0 139.0 -1.0
LE7 B1 / End 46.0 6.0 -141.0 0.0 135.0 2.0
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Bolts
Design data
[kN] [kN]
30 A325M - 1 328.8 197.3
Where:
– nominal tensile stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
Where:
– nominal shear stress AISC 360-16 – Table J3.2
– gross bolt cross-sectional area
– resistance factor
484.0 kN ≥ 26.5 kN
Where:
– clear distance, in the direction of the force, between the edge of the hole and the edge of
the adjacent hole or edge of the material
– thickness of the plate
– diameter of a bolt
– tensile strength of the connected material
– resistance factor for bearing at bolt holes
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
PP1a B1-bfl 1 E70xx - - 250 - - - - - OK
Page 285 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
30 A325M 40 14
Drawing
PP1 - PP1a
PP1 - PP1b
WID1
WID2
RIB1
RIB2
Members
Geometry
X
Name Support Forces in
[mm]
B1 / end Node 0
B2 / end N-Vy-Vz-Mx-My-Mz Node 0
Cross-sections
Name Material
169 - I530 A572 Gr.50
Bolts
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B1 / End 9410.0 0.0 -508.0 0.0 0.0 0.0
Check
Summary
Analysis 100.0% OK
Plates 0.3 < 5.0% OK
Bolts 91.8 < 100% OK
Welds 0.0 < 100% OK
Buckling Not calculated
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Symbol explanation
tp Plate thickness
σEd Equivalent stress
εPl Plastic strain
σc,Ed Contact stress
Fy Yield strength
εlim Limit of plastic strain
Bolts
Design data
ϕRn,tension ϕRn,shear
Grade
[kN] [kN]
36 A325M - 1 473.4 284.0
Symbol explanation
Ft Tension force
V Resultant of bolt shear forces Vy and Vz in shear planes
ϕRn,bearing Bolt bearing resistance
Utt Utilization in tension
Uts Utilization in shear
Utts Utilization in tension and shear
ϕRn,tension Bolt tension resistance - AISC 360-16 – J3.6
ϕRn,shear Bolt shear resistance - AISC 360-16 – J3.6
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
PP1a B1-bfl 1 E70xx - - 500 - - - - - OK
PP1a B1-tfl 1 E70xx - - 500 - - - - - OK
PP1a B1-w 1 E70xx - - 490 - - - - - OK
PP1b B2-bfl 1 E70xx - - 500 - - - - - OK
PP1b B2-tfl 1 E70xx - - 500 - - - - - OK
PP1b B2-w 1 E70xx - - 490 - - - - - OK
PP1a WID1 E70xx - - 250 - - - - - OK
B1-bfl 1 WID1 E70xx - - 250 - - - - - OK
PP1a WID3 E70xx - - 250 - - - - - OK
B1-tfl 1 WID3 E70xx - - 250 - - - - - OK
PP1b WID4a E70xx - - 250 - - - - - OK
B2-tfl 1 WID4a E70xx - - 250 - - - - - OK
PP1b WID4b E70xx - - 250 - - - - - OK
B2-bfl 1 WID4b E70xx - - 250 - - - - - OK
Symbol explanation
Buckling
Bill of material
Manufacturing operations
Welds
Bolts
Grip length
Name Count
[mm]
36 A325M 90 28
Drawing
PP1 - PP1a
PP1 - PP1b
WID1
WID3
WID4
Members
Geometry
X
Name Support Forces in
[mm]
COL / end Node 0
Cross-sections
Name Material
5 - I540 A572 Gr.50
Anchors
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 COL / End 54.0 10.0 -74.0 0.0 95.0 4.0
LE2 COL / End -36.0 -18.0 -36.0 0.0 29.0 -16.0
LE3 COL / End 0.0 198.0 -81.0 0.0 104.0 107.0
LE4 COL / End 0.0 45.0 -84.0 0.0 106.0 16.0
Foundation block
Check
Summary
Plates
Design data
Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0
Anchors
Design data
ϕNsa ϕVsa
Grade
[kN] [kN]
30 A325M - 1 325.9 145.3
Where:
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Where:
– resistance factor
– modification factor for concrete condition
– basic concrete pullout strength for headed anchor:
, where:
Where:
– reduction factor for anchor close to an edge or multiple anchors with small spacing:
, where:
, where:
Where:
– reduction factor for steel strength in shear in case of mortar joint
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 COL-bfl 1 E70xx - - 350 - - - - - OK
BP1 COL-tfl 1 E70xx - - 350 - - - - - OK
BP1 COL-w 1 E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 519 40 LE3 60.3 91.3 66.0 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 519 40 LE3 60.8 88.7 68.5 OK
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Concrete block
A1 A2 σ ϕfp,max Ut
Item Loads Status
[mm2] [mm2] [MPa] [MPa] [%]
CB 1 LE3 77580 654534 6.5 30.5 21.3 OK
Where:
– concrete block design bearing strength:
, where:
Buckling
Bill of material
Manufacturing operations
Welds
Anchors
Drawing
BP1
Members
Geometry
X
Name Support Forces in
[mm]
COL / end Node 0
Cross-sections
Name Material
6 - I632 A572 Gr.50
Anchors
N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 COL / End 28.0 -2.0 18.0 0.0 0.0 -8.0
LE2 COL / End -278.0 -2.0 -81.0 0.0 31.0 -8.0
LE3 COL / End -71.0 7.0 -94.0 0.0 327.0 28.0
LE4 COL / End -261.0 9.0 -160.0 0.0 213.0 19.0
LE5 COL / End -147.0 26.0 -48.0 0.0 0.0 111.0
Foundation block
Check
Summary
Plates
Design data
Material Fy εlim
[MPa] [%]
A572 Gr.50 344.7 5.0
Anchors
Design data
ϕNsa ϕVsa
Grade
[kN] [kN]
30 A325M - 1 325.9 145.3
325.9 kN ≥ 217.7 kN
Where:
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Where:
– resistance factor
– modification factor for concrete condition
– basic concrete pullout strength for headed anchor:
, where:
Where:
– reduction factor for anchor close to an edge or multiple anchors with small spacing:
, where:
, where:
Where:
– reduction factor for steel strength in shear in case of mortar joint
– resistance factor
– tensile stress area
– specified tensile strength of anchor steel:
, where:
Welds
tw w L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 COL-bfl 1 E70xx - - 225 - - - - - OK
BP1 COL-tfl 1 E70xx - - 225 - - - - - OK
BP1 COL-w 1 E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 615 47 LE3 82.6 108.9 75.8 OK
E70xx ◢ 7.1 ◣ ◢ 10.0 ◣ 615 47 LE3 82.0 107.8 76.1 OK
107.8 kN ≥ 82.0 kN
Where:
– nominal stress of weld material:
, where:
482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
Concrete block
A1 A2 σ ϕfp,max Ut
Item Loads Status
[mm2] [mm2] [MPa] [MPa] [%]
CB 1 LE3 65393 576278 14.6 30.5 47.8 OK
Where:
– concrete block design bearing strength:
, where:
Buckling
Bill of material
Manufacturing operations
Welds
Anchors
Drawing
BP1
Steel Connections
Detailed report
Connection: 2 - Fixed uniaxial both axis BP
--------------------------------------------------------------------------------------------------------
Family: Column - Base (CB)
Type: Base plate
Description: Fixed Base
--------------------------------------------------------------------------------------------------------
General information
Connector
Members
Column
Column type : Prismatic member
Section : I 870*60/650*85
Material : A572 Gr50
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 1210 mm
B: Transversal dimension : 890 mm
Thickness : 65 mm
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
--------------------------------------------------------------------------------------------------------------------
DL1 -9012.00 12.00 -696.00 1524.00 431.00 Design
DL2 0.00 0.00 0.00 0.00 0.00 Design
DL3 0.00 0.00 0.00 0.00 0.00 Design
DL4 0.00 0.00 0.00 0.00 0.00 Design
DL5 0.00 0.00 0.00 0.00 0.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
--------------------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 70.00 6.35 --
Weld size [1/16in] 5 5 -- table J2.4
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.04 0.01 DL1 0.26 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 327.71 176.33 DL1 0.54 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 327.71 1.56 DL1 0.00 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 15.33 DL1 0.01 DG1 p. 35
Elastic method weld shear capacity [KN/m] 1218.98 918.07 DL1 0.75 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.75
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 180.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 465.00 76.20 -- Sec. 7.7.1
Effective length [mm] 769.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 2.61 DL1 0.01 Eq. D-3
Pullout of anchor in tension [KN] 252.11 2.61 DL1 0.01 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 1318.79 13.03 DL1 0.01 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 140.03 69.27 DL1 0.49 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 774.37 69.27 DL1 0.09 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 1816.66 1524.00 DL1 0.84 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 2120.08 1524.00 DL1 0.72 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.00 DL1 0.00 Sec. D.7
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.84
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.04 0.01 DL1 0.23 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 327.71 56.05 DL1 0.17 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 327.71 0.00 DL1 0.00 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
Elastic method weld shear capacity [KN/m] 1218.98 131.40 DL1 0.11 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.23
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 180.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 465.00 76.20 -- Sec. 7.7.1
Effective length [mm] 769.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 0.00 DL1 0.00 Eq. D-3
Pullout of anchor in tension [KN] 252.11 0.00 DL1 0.00 Sec. D.4.1.1
Anchor shear [KN] 140.03 19.59 DL1 0.14 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 774.37 19.59 DL1 0.03 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 1816.66 431.00 DL1 0.24 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 2120.08 431.00 DL1 0.20 Sec. D.5.2.9,
D.6.2.9
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.24
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (DL1)
------------------------------------------------------------------------------
Maximum bearing pressure 9.59 [N/mm2]
Minimum bearing pressure 9.59 [N/mm2]
Maximum anchor tension 2.61 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 1057.26 [mm]
Bearing length 1057.26 [mm]
------------------------------------------------------------------------------
Anchors tensions
Minor axis
Maximum compression and tension (DL1)
----------------------------------------------------------------------------
Maximum bearing pressure 8.37 [N/mm2]
Minimum bearing pressure 8.37 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 1E33 [mm]
Bearing length 890.00 [mm]
----------------------------------------------------------------------------
Anchors tensions
General information
Connector
Members
Column
Column type : Prismatic member
Section : I 500*20*400*40
Material : A572 Gr50
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 820 mm
B: Transversal dimension : 520 mm
Thickness : 50 mm
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 5
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : No
Longitudinal dimension : 1100 mm
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
--------------------------------------------------------------------------------------------------------------
DL1 -1472.00 87.00 -82.00 15.00 16.00 Design
DL2 0.00 0.00 0.00 0.00 0.00 Design
DL3 0.00 0.00 0.00 0.00 0.00 Design
DL4 0.00 0.00 0.00 0.00 0.00 Design
DL5 0.00 0.00 0.00 0.00 0.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
--------------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Page 334 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 45.00 6.35 --
Weld size [1/16in] 5 5 -- table J2.4
WARNINGS
- There are anchors in invalid positions
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.03 0.00 DL1 0.13 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 193.91 36.12 DL1 0.19 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 193.91 0.65 DL1 0.00 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 9.83 DL1 0.01 DG1 p. 35
Elastic method weld shear capacity [KN/m] 1218.98 15.00 DL1 0.01 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.19
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 200.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 185.00 76.20 -- Sec. 7.7.1
Effective length [mm] 769.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 1.18 DL1 0.00 Eq. D-3
Pullout of anchor in tension [KN] 252.11 1.18 DL1 0.00 Sec. D.4.1.1
Side-face blowout of anchor in tension [KN] 211.42 1.18 DL1 0.01 Sec. D.4.1.1
Side-face blowout of group of anchors in tension [KN] 563.79 3.54 DL1 0.01 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 791.27 3.54 DL1 0.00 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 140.03 1.88 DL1 0.01 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 307.33 1.88 DL1 0.01 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 496.05 15.00 DL1 0.03 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 659.39 15.00 DL1 0.02 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.00 DL1 0.00 Sec. D.7
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.03
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
WARNINGS
- There are anchors in invalid positions
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.03 0.00 DL1 0.15 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 193.91 40.35 DL1 0.21 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 193.91 1.44 DL1 0.01 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 21.63 DL1 0.01 DG1 p. 35
Elastic method weld shear capacity [KN/m] 1218.98 10.26 DL1 0.01 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.21
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 200.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 185.00 76.20 -- Sec. 7.7.1
Effective length [mm] 769.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 2.60 DL1 0.01 Eq. D-3
Pullout of anchor in tension [KN] 252.11 2.60 DL1 0.01 Sec. D.4.1.1
Side-face blowout of anchor in tension [KN] 211.42 2.60 DL1 0.01 Sec. D.4.1.1
Side-face blowout of group of anchors in tension [KN] 669.50 7.79 DL1 0.01 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 791.27 7.79 DL1 0.01 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 140.03 2.00 DL1 0.01 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 307.33 2.00 DL1 0.01 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 496.05 16.00 DL1 0.03 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 659.39 16.00 DL1 0.02 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.00 DL1 0.00 Sec. D.7
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.03
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (DL1)
----------------------------------------------------------------------------
Maximum bearing pressure 3.99 [N/mm2]
Minimum bearing pressure 3.99 [N/mm2]
Maximum anchor tension 1.18 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 710.53 [mm]
Bearing length 710.53 [mm]
----------------------------------------------------------------------------
Anchors tensions
Minor axis
Maximum compression and tension (DL1)
----------------------------------------------------------------------------
Maximum bearing pressure 4.46 [N/mm2]
Minimum bearing pressure 4.46 [N/mm2]
Maximum anchor tension 2.60 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 404.52 [mm]
Bearing length 404.52 [mm]
----------------------------------------------------------------------------
Anchors tensions
Connection: 3 - Pinned BP
--------------------------------------------------------------------------------------------------------
Family: Column - Base (CB)
Type: Base plate
Description: Hinged base
--------------------------------------------------------------------------------------------------------
General information
Connector
Members
Column
Column type : Prismatic member
Section : I 500*10*350*20
Material : A992 Gr50
Longitudinal offset : 0 mm
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 560 mm
B: Transversal dimension : 520 mm
Thickness : 40 mm
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 5
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : No
Longitudinal dimension : 1050 mm
Transversal dimension : 1050 mm
Thickness : 1000 mm
Material : C40-50
Include grouting : Yes
Grout thickness : 50 mm
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 3
Longitudinal edge distance on the plate : 120 mm
Transverse edge distance on the plate : 110 mm
Anchor type : Headed
Head type : Hexagonal
Include lock nut : No
Anchor : M_30
Effective embedment depth : 500 mm
Total length : 629.6 mm
Material : A325
Fy : 0.558 kN/mm2
Fu : 0.725 kN/mm2
Cracked concrete : Yes
Brittle steel : No
Anchors welded to base plate : No
Anchor reinforcement
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
----------------------------------------------------------------------------------------------------------------
DL1 -3344.00 0.00 0.00 621.00 56.00 Design
DL2 0.00 0.00 0.00 0.00 0.00 Design
DL3 0.00 0.00 0.00 0.00 0.00 Design
DL4 0.00 0.00 0.00 0.00 0.00 Design
DL5 0.00 0.00 0.00 0.00 0.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
----------------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 95.00 6.35 --
Weld size [1/16in] 5 3 -- table J2.4
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.04 0.01 DL1 0.28 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 124.10 82.68 DL1 0.67 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 124.10 0.00 DL1 0.00 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
Elastic method weld shear capacity [KN/m] 1218.98 621.00 DL1 0.51 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.67
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Page 340 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 305.05 0.00 DL1 0.00 Eq. D-3
Breakout of anchor in tension [KN] 236.49 0.00 DL1 0.00 Sec. D.4.1.1
Pullout of anchor in tension [KN] 252.11 0.00 DL1 0.00 Sec. D.4.1.1
Anchor shear [KN] 126.90 103.50 DL1 0.82 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 472.98 103.50 DL1 0.22 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 683.48 621.00 DL1 0.91 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 860.08 621.00 DL1 0.72 Sec. D.5.2.9,
D.6.2.9
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.91
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (DL1)
----------------------------------------------------------------------------
Maximum bearing pressure 11.48 [N/mm2]
Minimum bearing pressure 11.48 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 1E33 [mm]
Bearing length 560.00 [mm]
----------------------------------------------------------------------------
Anchors tensions
Connection: 5 - Pinned BP
--------------------------------------------------------------------------------------------------------
Family: Column - Base (CB)
Type: Base plate
Description: BP-04
--------------------------------------------------------------------------------------------------------
General information
Connector
Members
Column
Column type : Prismatic member
Section : L 400
Material : A992 Gr50
Longitudinal offset : 0 mm
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 400 mm
B: Transversal dimension : 250 mm
Thickness : 15 mm
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 20
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : No
Longitudinal dimension : 900 mm
Transversal dimension : 700 mm
Thickness : 250 mm
Material : C40-50
Include grouting : Yes
Grout thickness : 50 mm
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 4
Longitudinal edge distance on the plate : 50 mm
Transverse edge distance on the plate : 50 mm
Anchor type : Headed
Head type : Hexagonal
Include lock nut : No
Anchor : M_24
Effective embedment depth : 175 mm
Total length : 271.68 mm
Material : A325
Fy : 0.558 kN/mm2
Fu : 0.725 kN/mm2
Cracked concrete : Yes
Brittle steel : No
Anchors welded to base plate : No
Anchor reinforcement
Type of reinforcement : Primary
Tension reinforcement : No
Shear reinforcement : Yes
Shear bar size : no. 8
Shear bar grade : 0.45 kN/mm2
Shear number of bars in major axis direction : 5
Shear number of bars in minor axis direction : 5
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
------------------------------------------------------------------------------------------------------------
DL1 186.00 0.00 0.00 68.00 13.00 Design
DL2 -114.00 0.00 0.00 68.00 13.00 Design
DL3 0.00 0.00 0.00 0.00 0.00 Design
DL4 0.00 0.00 0.00 0.00 0.00 Design
DL5 0.00 0.00 0.00 0.00 0.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
------------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 38.00 6.35 --
Weld size [1/16in] 20 4 -- table J2.4
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.04 0.00 DL2 0.03 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 17.45 7.80 DL2 0.45 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 17.45 15.58 DL1 0.89 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 7313.87 178.85 DL1 0.02 DG1 p. 35
Elastic method weld shear capacity [KN/m] 4875.91 106.25 DL1 0.02 Sec. J2.4
Elastic method weld axial capacity [KN/m] 7313.87 4650.00 DL1 0.64 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.89
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 100.00 96.00 -- Sec. D.8.1
Concrete cover [mm] 263.00 76.20 -- Sec. 7.7.1
Effective length [mm] 190.60 -- 234.40
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 191.95 23.25 DL1 0.12 Eq. D-3
Breakout of anchor in tension [KN] 102.94 23.25 DL1 0.23 Sec. D.4.1.1
Breakout of group of anchors in tension [KN] 207.98 186.00 DL1 0.89 Sec. D.4.1.1
Pullout of anchor in tension [KN] 150.16 23.25 DL1 0.15 Sec. D.4.1.1
Anchor shear [KN] 79.85 8.50 DL1 0.11 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 205.87 8.50 DL1 0.04 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 415.95 68.00 DL1 0.16 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 860.08 68.00 DL1 0.08 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.00 DL1 0.00 Sec. D.7
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.89
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression (DL2)
----------------------------------------------------------------------------
Maximum bearing pressure 1.14 [N/mm2]
Minimum bearing pressure 1.14 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 1E33 [mm]
Bearing length 400.00 [mm]
----------------------------------------------------------------------------
Anchors tensions
---------------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 23.25 [kN]
Minimum anchor tension 23.25 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location -1E33 [mm]
Bearing length 0.00 [mm]
---------------------------------------------------------------------------
Anchors tensions
Major axis
Results for tensile breakout (DL1)
1 556875.00 186.00 1, 2, 3, 4, 5, 6, 7, 8
------------------------------------------------------------------------------
General information
Connector
Members
Column
Column type : Prismatic member
Section : I 500X8X350X20
Material : A572 Gr50
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 820 mm
B: Transversal dimension : 520 mm
Thickness : 25 mm
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 5
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : No
Longitudinal dimension : 1100 mm
Transversal dimension : 800 mm
Thickness : 1500 mm
Material : C40-50
Include grouting : No
Anchor
Anchor position : Customized
Anchor coordinates:
Coordinate
Transverse Longitudinal
[mm] [mm]
-----------------------------------------
200.00 125.00
-200.00 125.00
200.00 350.00
-200.00 350.00
200.00 -350.00
-200.00 -350.00
0.00 350.00
0.00 -350.00
200.00 -125.00
-200.00 -125.00
-----------------------------------------
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
------------------------------------------------------------------------------------------------------------
DL1 54.00 4.00 95.00 74.00 10.00 Design
DL2 -36.00 16.00 29.00 36.00 18.00 Design
DL3 0.00 16.00 109.00 84.00 45.00 Design
DL4 0.00 107.00 104.00 81.00 198.00 Design
DL5 0.00 0.00 0.00 0.00 0.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
------------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 45.00 6.35 --
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.03 0.00 DL3 0.08 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 48.48 27.95 DL3 0.58 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 48.48 24.81 DL1 0.51 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 254.55 DL1 0.14 DG1 p. 35
Elastic method weld shear capacity [KN/m] 1218.98 84.00 DL3 0.07 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 262.81 DL1 0.14 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.58
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 200.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 185.00 76.20 -- Sec. 7.7.1
Effective length [mm] 769.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 40.73 DL1 0.12 Eq. D-3
Pullout of anchor in tension [KN] 252.11 40.73 DL1 0.16 Sec. D.4.1.1
Side-face blowout of anchor in tension [KN] 211.42 40.73 DL1 0.19 Sec. D.4.1.1
Side-face blowout of group of anchors in tension [KN] 563.79 122.18 DL1 0.22 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 333.87 194.20 DL1 0.58 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 175.04 8.40 DL3 0.05 Eq. D-20
Pryout of anchor in shear [KN] 307.33 8.40 DL3 0.03 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 496.05 84.00 DL3 0.17 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 233.71 84.00 DL3 0.36 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.00 DL1 0.00 Sec. D.7
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.58
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.03 0.00 DL4 0.12 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 48.48 34.14 DL4 0.70 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 48.48 35.44 DL4 0.73 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 347.12 DL4 0.19 DG1 p. 35
Elastic method weld shear capacity [KN/m] 1218.98 143.06 DL4 0.12 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 1308.75 DL4 0.72 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.73
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 200.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 185.00 76.20 -- Sec. 7.7.1
Effective length [mm] 769.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 58.19 DL4 0.17 Eq. D-3
Pullout of anchor in tension [KN] 252.11 58.19 DL4 0.23 Sec. D.4.1.1
Side-face blowout of anchor in tension [KN] 211.42 58.19 DL4 0.28 Sec. D.4.1.1
Side-face blowout of group of anchors in tension [KN] 669.50 232.75 DL4 0.35 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 333.87 285.18 DL4 0.85 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 175.04 19.80 DL4 0.11 Eq. D-20
Pryout of anchor in shear [KN] 307.33 19.80 DL4 0.06 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 496.05 198.00 DL4 0.40 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 233.71 198.00 DL4 0.85 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.75 DL4 0.62 Eq. D-32
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.85
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression (DL3)
----------------------------------------------------------------------------
Maximum bearing pressure 2.37 [N/mm2]
Minimum bearing pressure 2.37 [N/mm2]
Maximum anchor tension 40.08 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 152.54 [mm]
Bearing length 152.54 [mm]
----------------------------------------------------------------------------
Anchors tensions
----------------------------------------------------------------------------
Maximum bearing pressure 2.03 [N/mm2]
Minimum bearing pressure 2.03 [N/mm2]
Maximum anchor tension 40.73 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 132.72 [mm]
Bearing length 132.72 [mm]
----------------------------------------------------------------------------
Anchors tensions
Minor axis
Maximum compression and tension (DL4)
--------------------------------------------------------------------------
Maximum bearing pressure 3.62 [N/mm2]
Minimum bearing pressure 3.62 [N/mm2]
Maximum anchor tension 58.19 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 96.06 [mm]
Bearing length 96.06 [mm]
--------------------------------------------------------------------------
Anchors tensions
General information
Connector
Members
Column
Column type : Prismatic member
Section : I 600*12*225*16
Material : A572 Gr50
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 950 mm
B: Transversal dimension : 350 mm
Thickness : 45 mm
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 9
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : No
Longitudinal dimension : 1050 mm
Transversal dimension : 650 mm
Thickness : 1500 mm
Material : C40-50
Include grouting : No
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 4
Longitudinal edge distance on the plate : 55 mm
Transverse edge distance on the plate : 50 mm
Anchor type : Headed
Head type : Hexagonal
Include lock nut : No
Anchor : M_30
Effective embedment depth : 800 mm
Total length : 884.6 mm
Material : Class 8.8
Fy : 0.64 kN/mm2
Fu : 0.8 kN/mm2
Cracked concrete : Yes
Brittle steel : No
Anchors welded to base plate : No
Anchor reinforcement
Type of reinforcement : Primary
Tension reinforcement : Yes
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
--------------------------------------------------------------------------------------------------------------
DL1 -71.00 28.00 327.00 94.00 7.00 Design
DL2 -147.00 111.00 0.00 48.00 26.00 Design
DL3 -261.00 19.00 213.00 160.00 9.00 Design
DL4 -278.00 8.00 31.00 81.00 4.00 Design
DL5 28.00 8.00 0.00 18.00 2.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
--------------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 35.00 6.35 --
Weld size [1/16in] 9 3 -- table J2.4
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.02 0.01 DL1 0.33 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 157.07 124.15 DL1 0.79 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 157.07 90.88 DL1 0.58 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 3291.24 614.88 DL1 0.19 DG1 p. 35
Elastic method weld shear capacity [KN/m] 2194.16 133.33 DL3 0.06 Sec. J2.4
Elastic method weld axial capacity [KN/m] 3291.24 785.28 DL1 0.24 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.79
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 250.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 90.00 76.20 -- Sec. 7.7.1
Effective length [mm] 819.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 128.82 DL1 0.38 Eq. D-3
Pullout of anchor in tension [KN] 252.11 128.82 DL1 0.51 Sec. D.4.1.1
Side-face blowout of anchor in tension [KN] 161.21 128.82 DL1 0.80 Sec. D.4.1.1
Side-face blowout of group of anchors in tension [KN] 310.08 257.63 DL1 0.83 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 1055.03 466.39 DL1 0.44 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 175.04 20.00 DL3 0.11 Eq. D-20
Pryout of anchor in shear [KN] 224.32 20.00 DL3 0.09 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 310.64 160.00 DL3 0.52 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 527.52 160.00 DL3 0.30 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 1.13 DL1 0.94 Eq. D-32
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.94
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.02 0.01 DL2 0.28 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 157.07 93.35 DL2 0.59 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 157.07 61.10 DL2 0.39 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 3291.24 413.36 DL2 0.13 DG1 p. 35
Elastic method weld shear capacity [KN/m] 2194.16 29.68 DL2 0.01 Sec. J2.4
Elastic method weld axial capacity [KN/m] 3291.24 3084.33 DL2 0.94 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.94
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 250.00 120.00 -- Sec. D.8.1
Concrete cover [mm] 90.00 76.20 -- Sec. 7.7.1
Effective length [mm] 819.50 -- 1480.50
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 336.61 86.60 DL2 0.26 Eq. D-3
Pullout of anchor in tension [KN] 252.11 86.60 DL2 0.34 Sec. D.4.1.1
Side-face blowout of anchor in tension [KN] 161.21 86.60 DL2 0.54 Sec. D.4.1.1
Side-face blowout of group of anchors in tension [KN] 718.83 346.39 DL2 0.48 Sec. D.4.1.1
Anchors reinforcement in tension [KN] 1055.03 346.39 DL2 0.33 Sec. D.5.2.9,
D.6.2.9
Anchor shear [KN] 175.04 3.25 DL2 0.02 Eq. D-20
Pryout of anchor in shear [KN] 224.32 3.25 DL2 0.01 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 310.64 26.00 DL2 0.08 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 527.52 26.00 DL2 0.05 Sec. D.5.2.9,
D.6.2.9
Interaction of tensile and shear forces [KN] 1.20 0.00 DL1 0.00 Sec. D.7
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.54
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (DL1)
----------------------------------------------------------------------------
Maximum bearing pressure 8.13 [N/mm2]
Minimum bearing pressure 8.13 [N/mm2]
Maximum anchor tension 128.82 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 188.94 [mm]
Bearing length 188.94 [mm]
----------------------------------------------------------------------------
Anchors tensions
Minor axis
Maximum compression and tension (DL2)
--------------------------------------------------------------------------
Maximum bearing pressure 6.87 [N/mm2]
Minimum bearing pressure 6.87 [N/mm2]
Maximum anchor tension 86.60 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 75.56 [mm]
Bearing length 75.56 [mm]
--------------------------------------------------------------------------
Anchors tensions
Connection: 8 - Pinned BP
Page 358 of 363
STEEL STRUCTURE DESIGN CALCULATION of 363
--------------------------------------------------------------------------------------------------------
Family: Column - Base (CB)
Type: Base plate
Description: BP-03
--------------------------------------------------------------------------------------------------------
General information
Connector
Members
Column
Column type : Prismatic member
Section : L 400
Material : A992 Gr50
Longitudinal offset : 0 mm
Base plate
Base plate
Plate shape : Rectangular
Connection type : Unstiffened
Position on the support : Center
N: Longitudinal dimension : 400 mm
B: Transversal dimension : 250 mm
Thickness : 15 mm
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 5
Override A2/A1 ratio : No
Include shear lug : No
Support
With pedestal : No
Longitudinal dimension : 1000 mm
Transversal dimension : 1000 mm
Thickness : 1000 mm
Material : C40-50
Include grouting : Yes
Grout thickness : 50 mm
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 4
Longitudinal edge distance on the plate : 50 mm
Transverse edge distance on the plate : 50 mm
Anchor type : Headed
Head type : Hexagonal
Include lock nut : No
Anchor : M_24
Effective embedment depth : 300 mm
Total length : 396.68 mm
Material : A325
Fy : 0.558 kN/mm2
Fu : 0.725 kN/mm2
Cracked concrete : Yes
Brittle steel : No
Anchors welded to base plate : No
Anchor reinforcement
Type of reinforcement : Primary
Tension reinforcement : No
Shear reinforcement : Yes
Shear bar size : no. 8
Shear bar grade : 0.45 kN/mm2
Shear number of bars in major axis direction : 5
Shear number of bars in minor axis direction : 5
Demands
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
----------------------------------------------------------------------------------------------------------
DL1 0.00 0.00 0.00 490.00 230.00 Design
DL2 0.00 0.00 0.00 0.00 0.00 Design
DL3 0.00 0.00 0.00 0.00 0.00 Design
DL4 0.00 0.00 0.00 0.00 0.00 Design
DL5 0.00 0.00 0.00 0.00 0.00 Design
DL6 0.00 0.00 0.00 0.00 0.00 Design
DL7 0.00 0.00 0.00 0.00 0.00 Design
----------------------------------------------------------------------------------------------------------
Design calculations
Design for major axis
Base plate (AISC 360-16 LRFD)
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 38.00 6.35 --
Weld size [1/16in] 5 4 -- table J2.4
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Axial bearing [KN/mm2] 0.04 0.00 DL1 0.00 DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [KN*m/m] 17.45 0.00 DL1 0.00 DG1 Eq. 3.3.13
Flexural yielding (tension interface) [KN*m/m] 17.45 0.00 DL1 0.00 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
Elastic method weld shear capacity [KN/m] 1218.98 765.63 DL1 0.63 Sec. J2.4
Elastic method weld axial capacity [KN/m] 1828.47 0.00 DL1 0.00 Sec. J2.4
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.63
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Geometric Considerations
Dimensions Unit Value Min. Max. Sta. References
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors
Anchor spacing [mm] 100.00 96.00 -- Sec. D.8.1
Concrete cover [mm] 338.00 76.20 -- Sec. 7.7.1
Effective length [mm] 315.60 -- 984.40
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design Check
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchor tension [KN] 191.95 0.00 DL1 0.00 Eq. D-3
Breakout of anchor in tension [KN] 187.49 0.00 DL1 0.00 Sec. D.4.1.1
Pullout of anchor in tension [KN] 150.16 0.00 DL1 0.00 Sec. D.4.1.1
Anchor shear [KN] 79.85 61.25 DL1 0.77 Eq. D-20,
Sec. D.6.1.3
Pryout of anchor in shear [KN] 374.97 61.25 DL1 0.16 Sec. D.4.1.1
Pryout of group of anchors in shear [KN] 554.01 490.00 DL1 0.88 Sec. D.4.1.1
Anchors reinforcement in shear [KN] 860.08 490.00 DL1 0.57 Sec. D.5.2.9,
D.6.2.9
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.88
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (DL1)
------------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Anchors tensions
4.4 Appendix-1