Professional Documents
Culture Documents
30/4/2022 PRINT
372: Signal description, central electronic module
(CEM)
Signal description
Central Electronic
Module (CEM)
General
All the values given
below are between
the connections in
column 1 and
connection #A28 in
column 2 (power
ground). This applies
unless otherwise
indicated in the last
column.
Note! It is
important to
connect the
breakout box and
check the ground
terminals before
taking readings.
Connector E, Front-1
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #E1 Transmission Ubat at ignition in position II;
control module Ulow otherwise
(TCM), signal
supply
#2 #E2 Electrical power Ubat at ignition in position II;
steering module Ulow otherwise
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 2 of 16
(EPS), signal
supply
#3 #E3 Brake control Ubat at ignition in position I;
module (BCM), Ulow otherwise
signal supply
#4 #E4 Reserve - -
#5 #E5 Reserve - -
#6 #E6 Reserve - -
#7 #E7 Reserve - -
#8 #E8 Windshield washer Ulow Ubat/Ulow
motor, power
supply
#9 #E9 Reserve - -
#10 #E10 Engine control Ulow Ubat/Ulow
module (ECM),
waking
#11 #E11 High beam right- Ulow Ubat/Ulow
hand, power
supply
#12 #E12 Tailgate washer Ulow Ubat/Ulow
motor, power
supply
#13 #E13 Front left-hand Ubat/Ulow Ubat/Ulow
parking lamp,
power supply
#14 #E14 Back-up Ulow Ulow/Ubat
(reversing) lamp,
check signal
#15 #E15 Reserve - -
#16 #E16 Reserve - -
#17 #E17 Reserve - -
#18 #E18 30-supply to the Ubat Ubat
central electronic
module (CEM)
#19 #E19 Reserve - -
#20 #E20 30-supply to the Ubat Ubat
central electronic
module (CEM)
#21 #E21 30-supply to the Ubat Ubat
central electronic
module (CEM)
#22 #E22 30-supply to the Ubat Ubat
central electronic
module (CEM)
#23 #E23 30-supply to the Ubat Ubat
central electronic
module (CEM)
#24 #E24 Reserve - -
#25 #E25 Low beam left, Ubat/Ulow Ubat/Ulow
power supply
#26 #E26 Reserve - -
#27 #E27 Full beam left, Ulow Ubat/Ulow
power supply
#28 #E28 Ulow/Ulow Ulow/Ubat
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 3 of 16
Connector G, Front-2
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #G1 Communication During communication the Siren control
LIN bus 3 voltage is 0V - Ubat module (SCM)
#2 #G2 Front right-hand Ubat/Ulow Ubat/Ulow
parking lamp,
power supply
#3 #G3 Communication During communication the WMM
LIN bus 9 voltage is 0V - Ubat
#4 #G4 Reserve - -
#5 #G5 Reserve - -
#6 #B6 Battery Ulow Ulow The battery
temperature temperature
sensor, ground gauge removed
from and
including
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 4 of 16
structure week
200605
#7 #G7 Accelerator pedal Ulow Ulow
(AP) position
sensor, check
signal
#8 #G8 Reserve - -
#9 #G9 Relay, front fog Ubat Ulow/Ubat
lamp, control
signal
#10 #G10 Reserve - -
#11 #G11 Relay, headlamp Ubat Ulow/Ubat
wash / wipe,
control signal
#12 #G12 Clutch pedal Ulow Ulow
sensor, check
signal
#13 #G13 Battery Ulow U=0V-5V The battery
temperature temperature
sensor, signal gauge removed
from and
including
structure week
200605
#14 #G14 Communication The voltage is 1.5-2.5 V Electrical power
CAN_L high speed during communication steering module
network (EPS) / Brake
control module
(BCM) / Body
sensor cluster
(BSC) /
Transmission
control module
(TCM) /
Integrated
Starter Generator
(ISG)
#15 #G15 Communication The voltage is 2.0-3.5 V Electrical power
CAN_H high speed during communication steering module
network (EPS) / Brake
control module
(BCM) / Body
sensor cluster
(BSC) /
Transmission
control module
(TCM) /
Integrated
Starter Generator
(ISG)
#16 #G16 Communication The voltage is 2-3.5 V during Combustion
CAN_H low speed communication preheater module
network (CPM)
#17 #G17 Reserve - -
#18 #G18 Ulow/Ubat Ulow/Ubat
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 5 of 16
Relay, horn,
control signal
#19 #G19 Hood switch Ulow with the hood closed Pulsed signal,
Ulow-Ubat with the hood f=100Hz
open
#20 #G20 Reserve - -
#21 #G21 Clutch pedal Ulow U=5 V
sensor, power
supply
#22 #G22 Accelerator pedal Ulow U=5 V
(AP) position
sensor, power
supply
#23 #G23 Clutch pedal Ulow U=0.15–4.75V
sensor, power
supply
#24 #G24 Clutch pedal Ulow Ulow/Ubat I4–motor
sensor, power
supply
#25 #G25 Reserve - -
#26 #G26 Communication During communication the Xenon lamps
LIN bus 2 voltage is 0V - Ubat (GDL)
#27 #G27 Switch, brake fluid Ulow at normal level; Ubat at
level low level
#28 #G28 Switch, washer Ulow at normal level; Ubat at
fluid level levels below 0.7 liters
#29 #G29 Reserve - -
#30 #G30 Engine control Ulow/Ubat Ulow/Ubat Diesel only
module (ECM),
collision signal
#31 #G31 Accelerator pedal Ulow U=0.15–4.85V
(AP) position
sensor, check
signal
#32 #G32 Communication The voltage is 1.5-2.5 V Combustion
CAN L low speed during communication preheater module
network (CPM)
Connector A, Cockpit-1
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #A1 Dimmer, check Ulow Ulow-Ubat
signal
#2 #A2 Reserve - -
#3 #A3 Positive Ubat at ignition in position II;
temperature Ulow otherwise
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 6 of 16
coefficient (PTC)
heater, signal
supply
#4 #A4 Data link connector Ubat Ubat
(DLC), power
supply
#5 #A5 Reserve - -
#6 #A6 Reserve - -
#7 #A7 Reserve - -
#8 #A8 Phone module Ulow Ubat
(PHM), power
supply
#9 #A9 Multimedia module Ulow Ubat
(MMM) display,
power supply
#10 #A10 Supplemental Ulow Ubat
restraint system
module (SRS), 15-
power supply
#11 #A11 Reserve - -
#12 #A12 Reserve - -
#13 #A13 Reserve - -
#14 #A14 CEM, signal ground Ulow Ulow
#15 #A15 S-supply (Power Ulow (Key out), Ubat (key in)
supply from
ignition switch)
#16 #A16 X-supply to Ubat at ignition in positions I
passenger and II; Ulow otherwise
compartment,
power supply
#17 #A17 15-supply (Power Ubat (Key in positions II and
supply from III); Ulow otherwise
ignition switch)
#18 #A18 Steering wheel Ubat Ubat
module (SWM),
power supply
#19 #A19 Audio module Ubat Ubat
(AUD), 30-supply
#20 #A20 Reserve
#21 #A21 Climate control Ulow Ubat
module (CCM),
infotainment
control module
(ICM), power
supply
#22 #A22 Reserve - -
#23 #A23 Cigarette lighter, Ubat Ubat
power supply
#24 #A24 Reserve - -
#25 #A25 Courtesy lighting, Ubat/Ulow Ubat/Ulow
power supply
#26 #A26 Reserve - -
#27 #A27 Reserve - -
#28 #A28 Power ground Ulow Ulow
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 7 of 16
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 8 of 16
Connector B, Cockpit-2
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #B1 Positive Ulow Ubat- Pulse width
temperature Ulow/Ulow modulation
coefficient (PTC) (PWM) signal
heater, control
signal
#2 #B2 Light switch, Ulow/Ubat Ulow/Ubat Light switch in
control signal position 1
#3 #B3 Lamp, switch, Ubat-Ulow if activated; Ulow
hazard warning otherwise
signal flashers,
power supply
#4 #B4 Light switch, Ulow/Ubat Ulow/Ubat Light switch in
control signal position 0
#5 #B5 Alarm LED, power Alarm activated: 5V 0.5Hz Pulse width
supply 5% duty modulation
Alarm triggered: 5V 4Hz 25% (PWM) signal
duty
#6 #B6 Rear fog lamp LED Ulow Ubat/Ulow
in light switch,
power supply
#7 #B7 Reserve - -
#8 #B8 Communication The voltage is 2-3.5 V during Infotainment
CAN_H low speed communication control module
network (ICM) / Driver
information
module (DIM)
#9 #B9 Communication The voltage is 1.5-2.5 V Infotainment
CAN L low speed during communication control module
network (ICM) / Driver
information
module (DIM)
#10 #B10 Steering column Ubat approx. one second
lock module (SCL), after the key has been
power supply inserted or removed; Ulow
otherwise
#11 #B11 Diagnostic The voltage is 2.0-3.5 V
communication during communication
(CAN H) for the
high speed network
#12 #B12 Diagnostic The voltage is 1.5-2.5 V
communication during communication
(CAN_L) for the
high speed network
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 9 of 16
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 10 of 16
Connector C, Floor-1
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #C1 Switch parking Ubat Ulow/Ubat
brake, check signal
#2 #C2 Fuel tank filler Ubat/Ulow Ubat/Ulow
cover, control signal
#3 #C3 Left-hand stop Ubat/Ulow Ubat/Ulow
lamp, power supply
#4 #C4 Right-hand stop Ubat/Ulow Ubat/Ulow
lamp, power supply
#5 #C5 Reserve - -
#6 #C6 Rear fog lamp, Ulow Ubat/Ulow
power supply
#7 #C7 High level stop Ubat/Ulow Ubat/Ulow
lamp, power supply
#8 #C8 Unlocking tailgate, Ulow Ubat/Ulow
control signal
#9 #C9 Rear left-hand turn Ulow Ubat- Pulse width
signal lamp, power Ulow/Ulow modulation
supply (PWM) signal
#10 #C10 Rear right-hand Ulow Ubat- Pulse width
turn signal lamp, Ulow/Ulow modulation
power supply (PWM) signal
#11 #C11 Reserve - -
#12 #C12 Rear right-hand Ubat/Ulow Ubat/Ulow
parking lamp,
power supply
#13 #C13 License plate Ubat/Ulow Ubat/Ulow
lighting, power
supply
#14 #C14 Rear left-hand Ubat/Ulow Ubat/Ulow
parking lamp,
power supply
#15 #C15 Reserve - -
#16 #C16 Fuel pump (FP), Ulow Ubat/Ulow
power supply
#17 #C17 Subwoofer module Ulow Ubat/Ulow
(SUB), power
supply
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 11 of 16
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 12 of 16
Connector F, Floor-2
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #F1 Rear left-hand seat Ulow 4-5V/0-1V
belt buckle sensor,
check signal
#2 #F2 Rear center seat Ulow 4-5V/0-1V
belt buckle sensor,
check signal
#3 #F3 Rear right-hand Ulow 4-5V/0-1V
seat belt buckle
sensor, check signal
#4 #F4 Reserve - -
#5 #F5 Fuel level sensor Ulow U=0.5-4V Full: 0.5V
pump side, check Empty: 4V
signal
#6 #F6 Reserve - -
#7 #F7 Fuel level sensor, Ulow Ulow
common ground
#8 #F8 Reserve - -
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 13 of 16
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 14 of 16
sensor, signal
ground
#29 #F29 Reserve - -
#30 #F30 Communication The voltage is 2.0-3.5 V Supplemental
CAN_H low speed during communication restraint system
network module (SRS) /
Driver door
module (DDM) /
Passenger door
module (PDM)
#31 #F31 Outside Ulow U=0.5-4V
temperature
sensor, check signal
#32 #F32 Reserve - -
Connector H, Roof-2
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#15 #H1 LED seat belt Ulow Ubat/Ulow
reminder, power
supply
#16 #H2 LED reduced alarm Ulow Ubat/Ulow
position, power
supply
#17 #H3 Remote Keyless At communication the
Entry (RKE), signal voltage is Ubat-(1-1.5) V
#18 #H4 Roof console and Ubat Ubat
sun roof motor,
power supply
#19 #H5 Automatic anti- Ulow Ubat/Ulow
glare door mirror
inhibitor, control
signal
#20 #H6 Remote Keyless Ubat Ubat
Entry (RKE), power
supply
#21 #H7 Rain sensor module Ubat Ubat
(RSM), power
supply
#22 #H8 Communication The voltage is 2.0-3.5 V AEM
CAN_H low speed during communication
network
#23 #H9 Reserve - -
#24 #H10 Reserve - -
#25 terminal Reserve - -
#H11
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 15 of 16
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022
372: Signal description, central electronic module (CEM) Page 16 of 16
Connector D, Roof-1
Breakout Control Signal type Ignition off Ignition on Miscellaneous
box module Active / Not Active / Not
terminal terminal active active
#1 #D1 Reserve - -
#2 #D2 Reserve - -
#3 #D3 Roof lighting, Ulow Ulow
return cable
#4 #D4 Dimmer, check Ulow Ulow-Ubat
signal
#5 #D5 High level stop Ubat/Ulow Ubat/Ulow 4 door
lamp, power supply
#6 #D6 Reserve - -
#7 #D7 Roof lighting, Ubat/Ulow Ubat/Ulow
power supply
#8 #D8 Reserve - -
#9 #D9 Accessory Ulow Ulow
electronic module
(AEM) ground
#10 #D10 Mass movement Ulow Ulow
sensor (MMS) or
movement sensor
(IMS) (IMS
replaces MMS for
S40, C30, and V50
from and incl model
year 2012), rain
sensor (RSM) and
Remote Keyless
Entry (RKE),
ground
#11 #D11 Reserve - -
#12 #D12 Roof console and Ulow Ulow
sun roof, ground
#13 #D13 Reserve - -
#14 #D14 Sun roof control Ubat (for Ubat Active when the
module, power 5 minutes only ignition is off and
supply according to the neither of the
conditions on front doors have
the right) been opened
30/4/2022 PRINT
http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 4/30/2022