APPLICABLE MODEL: GSX-R750K9 EFFECTIVE ENGINE OR FRAME NO.: REFERENCE:
This bulletin is to inform you of set-up procedures of GSX-R750K9.
Please inform your dealers of this notice. GSX-R750K9 Set-Up Manual will not be issued because the set-up procedures for this model remain unchanged from GSX-R750K8 except the differences described below. To set-up GSX-R750K9, please use the GSX-R750K8 Set-Up Manual and this Service Bulletin.
GSX-R750K8 Set-Up Manual: 99505-01128-01E
DIFFERENCE BETWEEN GSX-R750K8 AND GSX-R750K9
MOTORCYCLE
DATE: Aug 4, 2008
PAGE: 2 OF 2 1. SAFETY CHECK OUT [Page: 33] COLD INFLATION TIRE PRESSURE SOLO RIDING DUAL RIDING After completion of the setting-up the motor- 250 kPa 250 kPa cycle all the following items should be dou- FRONT 2.50 kgf/cm2 2.50 kgf/cm2 36 psi 36 psi ble-checked to confirm that the operation and 290 kPa 290 kPa function of the motorcycle are satisfactory. REAR 2.90 kgf/cm2 2.90 kgf/cm2 Now, setting-up the motorcycle and pre-deliv- 42 psi 42 psi ery inspection have been completed and the motorcycle can be passed to the customer. ELECTRICALS ITEM CHECK FOR Light ENGINE AND TRANSMISSION Headlight high/low beam Lighting/Adjust
ITEM MEASURE SPECIFICATIONS Tail/Brake light
Engine oil Check/Refill 2 200 ml Turn signal light Lighting Fuel tank Drain/Fill 17.0 L Position light Throttle cable Check/Adjust Play: 2.0–4.0 mm License light Idle r/min Check/Adjust 1 100–1 300 r/min Instrument Lights Exhaust system Leakage Speedometer display Fuel system Tachometer light Leakage/Circlip connection High beam indicator light Engine coolant Check/Refill 2 700 ml Neutral indicator light Turn signal indicator light CHASSIS Engine rpm indicator light Lighting Coolant temperature indicator light/ ITEM MEASURE SPECIFICATIONS Oil pressure indicator light/ Disc brake Clean/Fluid level Fuel injection system indicator light/ Steering damper indicator light Front brake lever Check/Adjust Position 3 Fuel indicator light Rear brake pedal Check/Adjust Height: 65–75 mm Immobilizer indicator light Clutch cable Check/Adjust Play: 10–15 mm (Except for E-28) Check/Adjust/ Switch Operations Drive chain Slack: 20–30 mm Lubricate Ignition switch Oiling points All necessary points Dimmer switch Battery Filling electrolyte Turn signal switch Wiring and cable Routing/Operation Horn switch Wiring connectors Clean/Tight Passing light switch SP: 7 turns back R.DF: Hazard warning switch Operation 1-3/4 turns back Engine stop switch C.DF: Starter button Front fork Check/Adjust (High) 2 turns back Driving mode switch (Low) Brake switch 2-1/2 turns back Clutch lever position switch R.DF: 1-3/4 turns back Side stand/ignition interlock switch Rear shock C.DF: Check/Adjust (High) absorber 3 turns back ROAD TEST INSPECTION (Low) 2 turns back ITEM CHECK FOR Tighten all nuts and Torque those listed Starting/Acceleration/ Engine bolts in this manual Smoothness/Noise Cotter pins, circlip Transmission Operation/Noise Check and fasteners Drive chain Operation/Noise Paint and chrome Inspect/ Clutch Operation/Noise Wash and polish Brake Operation/Noise Warning label Select/Stick (For E-19) Steering Stability Suspension Operation SP= Spring R.DF= Rebound Damping Force Control cables Operation/Proper return C.DF= Compression Damping Force Leakage Fuel/Oil/Exhaust/Coolant Speedometer Operation Tachometer Operation Odometer/Trip meter Operation Instrument panel Operation