angle is 54 on a sphere of radius 27 cm. Determine the torque that can be applied to a 1 in diameter circular shaft if the shearing stress is not to exceed 8000 psi. Water having kinematic viscosity μk =1.3 X 10^(- 6) m^2/s flows in a 100mm diameter pipe at a velocity 4.5 m/s. Compute the Reynolds number. A 500 N man climbs at the middle of a 100 N ladder leaned against the wall. The top portion of the ladder is 4 m from the ground and its bottom is 2 m from the wall. Assuming smooth wall and a stopper at the bottom of the ladder to prevent slipping, find the reaction at the wall. 150 N Water enters the condenser at 30°C and leaves at 60°C. What is the temperature difference in °F? A stream flows at vs = 4.5 km/h. At what angle, O, upstream should a boat travelling at vь= 12 km/hr be launched in order to reach the shore directly opposite to the launch point? Find two consecutive odd numbers such that thrice the smaller number exceeds the larger by 12. 7&9 Gear used to transmit power at high velocity ratios between non- intersecting shafts that are usually but not necessarily at right angle. Worm Gear The velocity of water in the stream is 1.2 m/s. What is the height of the water column in the pitot tube? 7.34 cm How much torque can a cone torque transmit if the angle of conical elements is 10 degrees, the mean diameter of the conical clutch sections is 200 mm., and an axial force of 550 N is applied? Assume that the coefficient of friction between the clutch elements is 0.45. 142.53 N-m AVERAGE A steam condenser receives 10 kg per second of steam with an enthalpy of 2,570 kJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 kJ/kg. Cooling water passes through the condenser with temperature increases from 13°C to 24°C. Calculate the cooling water flowrate in kg/s. 523.26 kg/s if the F scale is twice the C scale, what is the reading in the Fahrenheit scale? F=320F A high alloy spring having squared and ground ends and has a total of 16 coils and modulus of elasticity in shear of 85 GPa. Compute the Wahl factor. The spring outside diameter is 9.66 cm and wire diameter is 0.65 cm. Kw = 1.1 Determine the maximum shearing stress in a helical spring composed of 20 turns of 3/4" diameter wire on a mean radius of 3" when the spring is supporting a load of 400 pounds. Use G=12 x 10^6 psi. 17,152psi A 76.2 mm diameter shafting of SAE 1040 grade cold rolled, having a yield point of 50 ksi and with a 3/4 x 3/4 x 5 inches key. Calculate the minimum yield point in the key in order to transmit the torque of the shaft. The factor of safety to be used is 2 and Sys= 0.5Sy. 47.12 ksi Given : log a x = 5y + log a (y), find the value of x. x=ya^5y A stone is dropped into a well and 4 seconds later the sound of the splash is heard. If sound travels at a speed of 340 m/sec, how deep is the well? 70.55m Lucy sold 100-pirated DVD. Eighty of them were sold at a profit of 30% while the rest were sold at a loss of 40%. What is the percentage gain or loss on the whole stock? 16% Compute the average mass of a 2 cubic meters propane at a pressure of 280 Kilonewton per square meter at 40 deg C temperature. 9.47 kg Forty liters of a 60 % salt solution are produced to a 45 % solution. How much solution must be drained off and replaced with distilled water so that the resulting solution contains only 45 % solution. 10 liters DIFFICULT With three different quantities x, y, and z of the same kind of liquid of temperatures 9, 21 and 38°C respectively, it is found that when x and y are mixed together the resultant temperature is 17°C and when y and z are mixed together the resultant temperature is 28°C. Find the resultant temperature if x and z were mixed. 25.92°C An air with mass of 0.454 kg and an unknown mass of CO2 occupy an 85 liters tank at 2068.44 Kpaa. If the partial pressure of the CO2 is 344.74 kPaa, determine its mass. 0.138KG Determine the wire diameter of a helical spring using Bergstrasser factor if the load is 130 lb and spring index of 8 if the maximum shearing stress of 50 ksi. 0.25in A flywheel rim which weighs 800 pounds has a mean diameter of 48 inches. The speed is to be maintained between 100 and 120 rpm. Considering that the effect of the arms and hub accounts for 12% of the rim weight, determine the capacity of the flywheel. Express your answer in ft-lb. 2685.68ft-lbs The torsional deformation of a SAE 1040 steel shaft is to 0.8° in a length of 1⁄2 meter. The shear stress is 69 Mpa. Determine the diameter of the shaft in millimeter. Steel modulus of elasticity is 79,300 Mpa or N/mm^2 62.32mm A body weighing 40 lb starts from rest and slides down a plane at an angle of 30° with the horizontal for which the coefficient of friction f = 0.3. How far will it move during the third second? 19.34ft To determine the width of a river a surveyor measures a line AB 120 m long on one bank. To a point C on the other bank he determines the angle BAC 48°36' and the angle ABC-54°42'. Find the width of the river. 75.7m A sphere of radius 10 m and a right circular cone of base radius 10 m and height 15 m stands on a table. At what height from the table should the two solids be cut in order to have equal circular sections? 3.54m A bituminous coal has the following composition: C = 71.5% H = 5.0% O = 7.0% N = 1.3% S = 3% Ash = 7.6% W = 3.4% Determine the theoretical weight of Nitrogen in lb/lb of coal. 7.526 lb/lbcoal A furnace wall consists of 35cm firebrick (k = 1.557W/m-K), 12cm insulating refractory (k = 0.346) and 20cm common brick (k = 0.692) covered with 7cm steel plate (k = 45). The temperature at the inner surface of the firebrick is 1,230 and at the outer face of the steel plate is 60. Atmosphere is 27. What is the value of the combined coefficient for convection and radiation from the outside wall? 41.3 W/m2-K