Professional Documents
Culture Documents
Drafts - Concrete - 11 Mar 2024
Drafts - Concrete - 11 Mar 2024
91
www.hilti.com.au
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
Specifier's comments:
1 Input data
Anchor type and size: HUS4-H 8 h_nom1
Return period (service life in years): 50
Item number: 2293134 HUS4-H 8x45 5/-/-
Effective embedment depth: hef = 32.3 mm (hef,ETA = 30.6 mm), hnom = 42.0 mm
Material: Carbon Steel
Approval No.: ETA-20/0867
Issued I Valid: 14/7/2022 | -
Proof: Design Method AS 5216:2021, Mechanical ETA-20/0867
Stand-off installation: eb = 0.0 mm (no stand-off); t = 3.0 mm
Ledger Angle :
R L1 x L2 x tL1 x tL2 x l = 70.0 mm x 30.0 mm x 3.0 mm x 3.0 mm x 70.0 mm;
R
- The anchor calculation is based on a rigid baseplate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] fc,cyl [N/mm ]
9,390 9,390 48.4 96.9 32.00
Group anchor ID
1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
0
VRk,s [kN] k7 VRk,s [kN] f Ms,V VRd,s [kN] V* [kN]
18.800 0.800 18.800 0.800 15.040 0.900
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k8 fc,cyl [N/mm ]
9,390 9,390 48.4 96.9 1.000 32.00
Group anchor ID
1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
5 Combined tension and shear loads (AS 5216:2021, Section 8.1.1, 8.1.2)
Steel failure
a a
bN + bV £ 1.0
Concrete failure
a a
bN + bV £ 1.0
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the baseplate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
7 Warnings
• The anchor design methods in PROFIS Engineering require rigid baseplates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the baseplate are not considered - the
baseplate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required baseplate thickness with CBFEM to limit the stress of the baseplate based on the assumptions explained
above. The proof if the rigid baseplate assumption is valid is not carried out by PROFIS Engineering. Input data and results must be
checked for agreement with the existing conditions and for plausibility!
• In general, the conditions given in ETAG 001, Annex C, section 4.2.2.1 and 4.2.2.3 b) are not fulfilled because the diameter of the clearance
hole in the fixture acc. to Annex 3, Table 3 is greater than the values given in Annex C, Table 4.1 and AS5126 for the corresponding
diameter of the anchor. Therefore the design resistance for anchor groups is limited to twice the steel resistance (of a single anchor) in
accordance with the approval.
• Checking the transfer of loads into the base material is required in accordance with AS 5216:2021, Appendix C!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.2.2.1 of AS 5216:2021! For larger
diameters of the clearance hole, see section 2.2 of SA TS 101: 2015!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) the minimum concrete cover defined in the design settings is used as the concrete
cover of the edge reinforcement.
• Load transfer from supplementary reinforcement to the structural member shall be verified by the responsible structural engineer.
• With supplementary reinforcement and post-installed anchors, please ensure that in the jobsite the rebars are not drilled through.
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
8 Installation data
Ledger Angle: L1 x L2 x tL1 x tL2 x l = 70.0 mm x 30.0 mm x 3.0 mm x 3.0 mm x Anchor type and size: HUS4-H 8 h_nom1
2
70.0 mm; Steel: Custom baseplate material; E = 200,000.00 N/mm ; fyk =
2
235.00 N/mm
Hole diameter in the fixture: df = 12.0 mm Item number: 2293134 HUS4-H 8x45 5/-/-
Plate thickness (input): 3.0 mm Maximum installation torque: -
Recommended plate thickness: not calculated Hole diameter in the base material: 8.0 mm
Drilling method: Hammer drilled Hole depth in the base material: 52.0 mm
Cleaning: Clean the drill hole. Under the conditions - according to fastener size Minimum thickness of the base material: 82.0 mm
and drilling direction - given in the ETA and MPII (IFU), the cleaning of the drill
hole may be omitted.
Hilti HUS screw anchor with 40 mm embedment, 8 h_nom1, Steel galvanized, installation per ETA-20/0867
y
35.0 35.0
15.0
15.0
13.5
1
x
15.0
15.0
35.0 35.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.91
www.hilti.com.au
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - 11 Mar 2024 Date: 11/3/2024
Fastening Point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan