Professional Documents
Culture Documents
Benefusion SP5
Appearance
Syringe pump
Benefusion
SP5
Benefusion SP5 Appearance-Front view
Push box:
Syringe : Simple and flexible installation
5/10/20/30/50/60ml syringes
Alarm light:
Distance can be seen, the user
can quickly notice
Battery box:
Easy to replace battery
RS232:
AC IN Data transfer to PC/software upgrade/update the Dock
system
Nurse call;
DC IN
Benefusion SP5 Appearance-side view
Safe lock:
Safer Make the pump superposition safer, more reliable
Benefusion SP5 Operation-Key function introduction
A total of 12 buttons
CLEAR/
BACK Edit status, press to clear values.
For high/middle level alarm, press to eliminate the alarm sound for
SILENCE
2 minutes, for low level alarm, press to clean the alarm.
Operation
Syringe pump
Benefusion
SP5
Benefusion SP5 Operation-BOOT Self testing
Self testing progarm: Memory, communication, alarm lamp, power supply, the pressure
coefficient, etc.;
Maximum guarantee the machine running normally before set parameters, to ensure
safety in advance.
Benefusion SP5 operation-installation and setting
Benefusion SP5 Operation-Start and finish
Benefusion SP5 Infusion Mode
Bolus Rate:0.10-2000ml/h
Benefusion SP5 DPS & Anti-Bolus
Benefusion SP5 KVO
KVO (Keep Vein Open) means to keep the vein open, during which the
infusion pump continues infusion at a very low rate after finishing the
infusion in order to prevent blood backflow or vascular blockage.
Principle
Syringe pump
Benefusion
SP5
Benefusion SP5 Principle-Instruction
S y rin g e P lu n g e r h o ld e r
M o to r
L e a d s c re w
G e a r s & c o g s t o tu rn th e
le a d s c re w
D ire c tio n o f m o v e m e n t
Microcomputer control system sends pulses stepper motor rotation,stepper motor drive
screw rotation movement into linear motion,push the syringe piston for injection
liquid,injection liquid in the syringe into human body.
Motor
Leadscrew
22
Benefusion SP5 Principle-Hardware(Microcomputer)
Benefusion SP5 Principle-Hardware(Microcomputer)
Host control Host CPU
Keyboard PCBA :
Key management section is responsible for (a total of 12 key, the power
switch directly to the CPU power supply module, other key by management
CPU) scanning processing, alarm lamp driver, LCD backlight control (8
gears adjustable), and other functions
Pressure-board PCBA :
Pressure-detect board including detection circuit and detection circuit of
the reign of syringes, responsible for process pressure sensor signal and the
syringe in detecting signal and sends the information to the monitoring
section.
Benefusion SP5 Installation
Calibration
Infusion Pump
Benefusion SP5
Benefusion SP5 Maintenance-syringe calibration
Before use non-defined syringe brand,we should make the calibration in System
Maintenance.
The purpose of calibration:Because there is mechanical error between short potentiometer (user Identity
syringe size) and emptying position in each machine, in order to identify the outer diameter of the syringe
and syringe emptying position more precise, each machine will calibrate the displacement sensor at the
System Maintenance.
Registration mast close Short potentiometer and empty tool:32mm
Short potentiometer and empty tool: 13.5mm
to the upper cover
Detection
Syringe pump
Benefusion SP5
Benefusion SP5 Maintenance-AD value
The instruction of AD value screen : System Maintenance-password(6686)—sensor AD value
Sensor interface
AD value corresponds to
based on which order of
Natural state natural state several binary
Convex edge detection
optocoupler ( pull the handle at short
potentiometer ) Retain 1 Highest level
Screw clutch optocoupler (push the
handle of slider ) Retain 0 Middle level
Pressure detection optocoupler (install
syringe) Retain 1 Lowest level
ODia means AD value of short potentiometer, pull the short potentiometer handle smoothly, the ODia value will be
larger, the scope should be between 0-4095 ;
Shift table shown emptying detection optocoupler AD value (ie: similar long potentiometer SK pump), consisting of
a total of four optocouplers, four optocoupler corresponding four binary digits, the machine leftmost lowest position,
each optocoupler outputs AD when the block is 1, the output is not blocked when AD is 0;
Pre table AD showing pressure sensor output value, when the pressure to the pressure sensor, this value should be
increased;
Code table code shown optocoupler output disc detection AD value, under normal circumstances, the motor rotates,
this value should be between 0,1,2,3 cycle ;
Benefusion SP5 Maintenance and Repair
Upgrade
Syringe pump
Benefusion SP5
Benefusion SP5 Maintenance-Upgrate
Login PW:25931501
Multifunction
serial port line
Troubleshooting
Syringe pump
Benefusion
SP5
Benefusion SP5 Malfunction Causes and Elimination
Can’t identify 1.short potentiometer slip handle and 1.mechanical card sets short
the syringes mechanical card sets out;2.Malfunction potentiometer slip handle ;
of short potentiometer 2.Replace short potentiometer
Flange detect 1.Malfunction of flange detect Repair wire or replace flange detect
failure board
Benefusion SP5 Malfunction Causes and Elimination
Detecting 1.Bad connect with screw clutch 1.Repair or replace the FPC wire ;
FPC ; 2.Repair or replace the 6Pin wire ;
faulty in
2.Bad connect with 6Pin wire ; 3.Replace pressure test board
syringe
3.Malfunction of pressure test
placing. board
Screw 1.Bad connect with screw clutch 1.Repair or replace the FPC wire ;
FPC wire ; 2.Replace screw clutch board ;
clutch fault
2.Malfunction of screw clutch
detection board
Benefusion SP5 Maintenance and Repair
Disassembly
Syringe pump
Benefusion
SP5
Benefusion SP5 Disassembly-Whole structure
S/
N Part Number Part Name & Spec QTY
Multi-channel pumps hasp (common
1 115-021570-00 mode material) 1
Multi-channel pumps hasp (common
2 043-004208-00 mode material) 1
3 043-004180-00 Multifunction interface cover 1
Pan head screw M3x8(GB/T818)
4 030-000305-00 Nickel-plated steel double gasket 16
5 115-021569-00 SP5 UP cover assembly 1
6 115-021563-00 SP5 pump body assembly 1
7 049-000662-00 SP5 slider screw rubber plug 3
8 049-000664-00 Foot pad 4
9 115-021571-00 SP5 door assembly 1
Wire FPC electron wire 10P
separation distance 1.0mm
10 050-001401-00 length120mm 1
11 009-002714-00 Strap,3x150mm 2
JP1
JP10
Earth wire
Benefusion SP5 Dismounting-Pump body
Cut the strap
J1connector