Professional Documents
Culture Documents
Manual Spider 8
Manual Spider 8
PC measurement electronics
Spider8
Spider8-30 and
Spider8-01
B0405-7.0 en
HBM
Contents
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
A
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
1
2
3
3
4
C
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
1
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Installing modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Switching on Spider8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Installing software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C-3
C-4
C-6
C-7
Spider8
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
1
2
3
5
Spider8
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
Spider8
Safety instructions
Spider8
Spider8
Residual dangers
The performance and list of components supplied with the Spider8
cover only part of the scope of measurement technology. In addition,
equipment planners, installers and operators should plan, implement
and respond to the safety engineering considerations of
measurement technology in such a way as to minimise residual
dangers. Existing regulations on the subject must be observed.
Reference must be made to residual dangers connected with
measurement technology.
If there is any risk of residual dangers when working with the
Spider8, it is pointed out in this introduction by means of the
following symbols:
Symbol:
Meaning:
DANGER
Maximum danger level
Symbol:
Meaning:
WARNING
Dangerous situation
Spider8
CAUTION
Symbol:
Meaning:
Symbol:
NOTE
Symbol:
Meaning:
CE mark
Spider8
Working safely
Error messages should only be acknowledged if the cause of the
error is removed and no further danger exists.
Power pack
The mains plug must be plugged into a gropunding outlet only
(protection class I). The power supply pack complies with protection
class I.
Do not open the power pack!
Never pull the mains plug from the socket by the mains lead. Do not
operate the device if the mains lead is damaged.
Spider8
If an amplifier module is removed, the plug-in unit must be closed off
with a blank plate.
The device complies with the safety requirements of DIN EN 60364;
protection class III.
Ensure that with all devices connected to the Spider8 (e.g. PC,
transducers, etc.) the mains voltage is separated safely from
extra-low voltages (double insulation).
In order to ensure adequate immunity from interference, use only
Greenline shielded ducting (see HBM offprint Greenline shielding
design, EMC-compliant measuring cable; G36.35.0)
Spider8
Spider8
10
Spider8
Introduction
A-1
Introduction
Spider8
A-2
Spider8
Introduction
Introduction
A-3
Introduction
all about the list of components supplied with your Spider8, and all
the things your Spider8 can do
Structure of the PC
measurement
electronics
Spider8
about the components that make up the device, the meaning of the
sockets on the back of the Spider8 and the control elements you can
find on the front panel
Commissioning
all the steps you need to take in order to make your measurement
chain ready for use. This includes such things as installing modules
and loading the correct software
Connecting up
how to connect up the Spider8 to the power pack supplied, and to all
kinds of transducers, PCs and printers
Configuring the
Spider8 with the
setup program
how to configure Spider8 with the setup program so that you can display current measured values or carry out taring
Specifications
Keyword index
Declaration of
conformity
Introduction
A-4
Introduction
A-5
What is Spider8
NOTE
Naming conventions:
The name Spider8 in this Operating Manual also applies to the
600Hz version and the DC version.
If the text applies exclusively to the 600 Hz version, the name
Spider8-30 is used.
Spider8-01 applies to both the 600 Hz version and the 4.8 kHz
version.
Both these device types can be operated in a mixed system.
Spider8
A-6
Introduction
Spider8:
Spider8 is an electronic measuring system for PCs for electric
measurement of mechanical variables such as strain, force,
pressure, path, acceleration and for temperatures.
All the signal conditioning - excitation for passive transducers and
amplification, digitalization, computer interface and connection
technology for a maximum of 8 channels - is combined in one
housing.
Spider8 is connected to the computer via the printer port or via an
RS232 interface and is then ready for immediate use.
All the required settings are made by the computer through
commands - there are no potentiometers, switches, solder bridges
or jumpers. It is only necessary to open the Spider8 housing if you
want to install a module.
Spider8-30:
The Spider8-30 uses its 600Hz carrier frequency amplifier to
manage all measurement tasks with S/G in quarter, half or full bridge
connection.
Three installed compensating resistors (120 , 350 , 700 ) are
available for measuring with S/G quarter bridges and are accessible
through the various connector pins.
The shunt calibration, when each channel is detuned by 1 mV/V, is
used to determine and correct the sensitivity loss. The SR30 module
extends the measurement options by additional S/G channels.
Spider8
Introduction
A-7
Spider8
Introduction
A-8
Spider8
Introduction
3.1
A-9
Module
Spider8
Spider8-30
Spider8-01/30
Spider8-01/55
SR01
SR30
SR55
Spider8
Introduction
A-10
0
1
4,8kHz
A/D
"10V
4,8kHz
A/D
"10V
A/D
CPU
SR01
up to 4
expansion
modules
4,8kHz
A/D
SR55
3 status signals
8 I/Os
8 inputs
Trigger
Spider8
RS-232C
DC
"10V
4 channels of
the basic
device
PC Printerport
To next Spider8 or to
printer
Introduction
A-11
600 Hz
RS-232C
A/D
4 channels of
the basic
device
"10V
CPU
+
DC
PC Printerport
A/D
SR01
up to 4
expansion
modules
600Hz
A/D
3 status signals
Trigger
8 I/Os
SR30
8 inputs
"10V
To next Spider8 or
to printer
Spider8
Introduction
A-12
DC
RS-232C
A/D
4 channels
of the basic
device
CPU
DC
SR01
A/D
up to 4
expansion
modules
600Hz
A/D
+
"10V
SR30
3 status signals
Trigger
8 I/Os
8 inputs
+
I
Spider8
PC Printerport
To next Spider8
or to printer
Introduction
A-13
DC
RS-232C
A/D
4 channels
of the basic
device
+
U
+
CPU
DC
I
SR01
A/D
up to 4
expansion
modules
4,8 kHz
A/D
To next Spider8
or to printer
3 status signals
Trigger
8 I/Os
SR55
8 inputs
"10V
PC Printerport
Spider8
A-14
Spider8
Introduction
B-1
Spider8
B-2
Spider8
B-3
Connection facilities
Channels
SPIDER8
carrier-frequency 4.8kHz
13
For Spider8-30:
SPIDER8-30 TF
600Hz
Ground connection
Spider8-01:
DC/4.8 kHz
DC/600 Hz
Meaning
Channel 0 to 7
Transducer port
Port for PC
Spider8
B-4
1.1
13
Ground
+VIN
*)
4 3
2 1
SELV circuit
(separated extra-low
voltage)
On/Off
Mains
connection
1.2
B-5
Modules (carrier-frequency/DC)
SPIDER8
carrier-freq
uency
4.8kHz
13
DC module
Channel
-
0...7
0...7
0...7
0...7
-
0...7
0..7
0...7
0...7
DC 1V
0...7
100mV DC
DC current
Frequency (counter)
Resistance
Potentiometer
Thermocouple
0, 1
0...7
-
0...7
-
0...7
0...7
0...7
0...7
Chapter C Commissioning tells you how you can later fit channels
4 to 7 with modules.
Spider8
B-6
Interfaces
Spider8
2.1
B-7
PC/Master
13
13
25
14
from PC (Master)
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
nWrite
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data 8
Intr
nWait
UserDefine 1
UserDefine 3
nDStrb
UserDefine 2
nInit
nAStrb
Clock in* (Synchronisation)
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Housing
Spider8
B-8
2.2
Printer/Slave
14
14
25
13
to printer (Slave)
Spider8
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
nWrite
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data 8
Intr
nWait
UserDefine 1
UserDefine 3
nDStrb
UserDefine 2
nInit
nAStrb
Clock out* (Synchronisation)
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Housing
2.3
B-9
RS-232-C
from PC (Master)
Pin
Assignment
Free
TD
RD
Free
Ground
DTR
CTS
RTS
Free
Socket housing
Protective ground
Spider8
B-10
8 bit
1
even
9600 Baud
You can actually set up the interface to suit your own requirements
with the command BDR.
Spider8
B-11
I / O socket
Eight digital inputs and eight I/Os (8-bit input / 8-bit output) are
available on this socket besides control signals and status
messages. The contacts are not electrically isolated.
Pin assignment for the I/O socket:
14
25
13
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
+5V/Ri = 1k
Ground
Input 14
Input 12
Input 10
Input 8
Ground
MSR (Measure)*
Ground
Input / Output 6
Input / Output 4
Input / Output 2
Input / Output 0
Start (external trigger for measurement sequence)
Input 15
Input 13
Input 11
Input 9
COMMON (common protective diode connection for external relay)
ERR (Command Error)*
RDY (Waiting for Trigger)*
Input / Output 7
Input / Output 5
Input / Output 3
Input / Output 1
Spider8
B-12
Start
H
(ext. trigger,
input)
L
MSR
(measure
output)
ts
tm
tp
RDY
H
(wait for trigger,
output)
L
Time
MSV
command
Trigger:
external, internal;
TRG command
Stop:
required
number of values
reached;
STP command
Spider8
B-13
A START signal on pin 14 of the I/O socket can start and stop a
measurement run.
+5V
+5V
max. +35V
30k
START
1k
HC
D
(Pin 14)
470p
Ground
(Pins 2, 9, 7)
+5V
+5V
max. +35V
30k
1k
Input 8...15
HC
470p
D
D
(Pins 3...6,
15...18)
Ground
(Pins 2, 9, 7)
Spider8
B-14
+5V
50k
Common
(Pin 19)
ERR (Pin 20)
MSR (Pin 8)
RDY (Pin 21)
max.100mA
+
max.50V
-
Ground (Pin 7)
+5V
50k
Common
(Pin 19)
Output 0...7
max. 100mA
max.50V
(Pins 10...13, 22...25)
Ground (Pin 9)
IN
Spider8
+
-
B-15
Front panel
On/off switch
LEDs
The three LEDs show you the operating status of the device.
After switching on, the LEDs light up
POWER (green)
TRANSFER (yellow)
ERROR (red)
After a successful system start the green LED stays on.
Spider8
B-16
Spider8
Commissioning
C-1
Commissioning
Spider8
C-2
Spider8
Commissioning
C-3
Commissioning
This chapter shows you the steps you need to take in order to
make your measurement chain ready for use (Spider8, PC and
transducer).
Update firmware:
Existing Spider8 can be brought up to date with the Spider8 System
CD.
C-4
1.1
Installing modules
A
Cover
A
A
1. Remove the four caps (A) from the top of the Spider8 housing
(prise them up with your thumb).
2. Undo the four screws (M4) with a cross-headed screwdriver.
3. Remove the cover.
4. Unscrew the appropriate blank plates from the rear panel of the
housing.
5. Plug the module into the rear panel of the housing as shown in
Fig. C 1 and press the connectors together. Fasten the module
firmly in place with the screws (B).
Blank plate
Fig. C 1: Installing a module
Spider8
Connector
C-5
6. When you have installed all the required modules in this way,
close the cover and fasten it again with the screws.
7. Fit the caps to the top of the housing.
8. Connect your PC to the Spider8 (see Chapter D Connecting a
PC).
9. Connect your transducer to the specially provided sockets on the
back of the Spider8 (see Chapter D Connecting transducers).
If you are using a cable you have made up yourself, please note
the pin assignment for your transducers in Chapter D
Connecting a transducer.
Spider8
C-6
1.2
Switching on Spider8
ON
OFF
The Spider8 carries out a function test (all 3 LEDs light up briefly)
and stores a record of the components that are present.
If the function test is positive, the power indicator lights up.
Spider8
C-7
1.3
Installing software
When you start the installation program, you are asked to specify
the drive and path for your installation. The default is c:\Spider8.
Then confirm Install.
If the specified directory does not exist, you are asked whether it
should be created. Click on OK.
In the following window you will be asked to enter the company
and user name. Confirm the information with Continue. The
program starts copying the setup files.
Spider8
C-8
If necessary you can terminate the installation before the end with
Exit and Cancel.
Note:
The installation program writes certain system files to your
Windows\System directory. If there are any files already present
with the same names, these are saved in the WINSAVE setup
sub-directory.
b. Installing Spider Control
See Operating Manual Spider8 Control
You have now taken all the necessary steps to make sure that your
measurement chain (Spider8 and transducers) is ready for use.
Spider8
Connecting
D-1
Connecting
Spider8
D-2
Spider8
Connecting
D-3
Shielding design
Until now:
In the case of shielding connections that have been customary with
HBM up to now, the shielding is linked to a connector pin.
This solution provides only limited EMC protection and should no
longer be used.
gy
12
1*
GREENLINE
wh
bk
rd
bu
gn
gy
ye
NOTE
Use standard HBM cable for the transducer connection.
When using other shielded, low-capacitance measuring
cable, connect the transducer cable shielding to the
connector housing in accordance with the HBM Greenline
information sheet (Ref. G 36.35.0). This ensures EMC
protection.
Spider8
D-4
13
Spider8
D-5
Connecting transducers
13
Spider8
D-6
DC module
Channel
Channel
Channel
0...7
0...7
0...7
0...7
0...7
0...7
0...7
DC 10V
0..7
0...7
0...7
DC 1V
0...7
100mV DC
0...7
DC current
0...7
Frequency (counter)
0, 1
1)
2)
Spider8
Resistance
0...7
Potentiometer
0...7
0...7
Thermocouple
0...7
D-7
Channels 0-3
(optionally 4-7)
1
9
5
6
8
15
sub-D
connector
15-pin
Spider8
13
12
Spider8
D-8
1
9
Measurement signal
Measurement signal
Sensor circuit
Sensor circuit
Transducer
F
G
E
MS3101A
16S-1S
Spider8
5
6
8
15
13
12
sub-D
connector
15-pin
Spider8
D-9
bu
rd
Feedback
bridges
15
gn
gy
13
12
Spider8
D-10
5 4
2 1
Fasten
cable ends
5 4
2 1
Spider8
2.
3.
4.
5.
6.
3.1
D-11
S/G transducers
15-pin socket
1
9
S/G transducers - whether half bridge, full bridge or single S/G - are
passive transducers with the following features:
They must be supplied with an excitation voltage
They are S/G full bridges
A transducer is characterised by the following data
- Nominal load (e.g. 20kg)
- Nominal sensitivity (for S/G transducers e.g. 2mV/V)
- Resistance: maximum 1k, minimum 120
Typical S/G transducers are load cells and force transducers.
15-pin socket
wh
rd
bk
bu
gn
gy
1 Measurement signal
15
4 Measurement signal
2 Bridge excitation
voltage
3 Bridge excitation
voltage
13
3 Sensor circuit
12
2 Sensor circuit
Spider8
D-12
1
9
wh
1 Measurement signal
2 Bridge excitation
voltage
3 Bridge excitation
voltage
15-pin socket
bk
bu
gn
gy
Spider8
13
3 Sensor circuit
12
2 Sensor circuit
D-13
15-pin socket
15-pin socket
bk
Active S/G
e.g. rosette
12
2 Bridge excitation
voltage
2 Sensor circuit
wh
bu
14
Free
Free
1 Measurement signal
RE
13
Bridge excitation
voltage
3 Sensor circuit
Spider8
D-14
Connection to Spider8-30
Connection to carrier-frequency module SR30
8
3.1.4
15
15-pin socket
15-pin socket
bk
RS/G
120
350
700
Link open
wh
bu
12
2 Bridge excitation
voltage
2 Sensor circuit (open)
1 Measurement signal
3
or
Compensating resistor
(internal):
Pin3: 120
Pin10: 350
Pin9: 700
or
10
9
13
Spider8
Bridge excitation
voltage
3 Sensor circuit
D-15
Connection to Spider8-30
Connection to carrier-frequency module SR30
8
15
1
9
3.1.5
15-pin socket
15-pin socket
bk
RS/G
120 to
1000
12
2 Bridge excitation
voltage
2 Sensor circuit (open)
1 Measurement signal
3
or
Compensating resistor
(internal):
Pin3: 120
Pin10: 350
Pin9: 700
5
Link open
wh
bu
Ruser
or
10
9
13
Ruser =
RS/G -
Bridge excitation
voltage
3 Sensor circuit
Rinternal
D-16
Connection to Spider8-30
Connection to carrier-frequency module SR30
8
15
3.1.6
15-pin socket
15-pin socket
bk
RS/G
12
2 Bridge excitation
voltage
2 Sensor circuit (open)
wh
1 Measurement signal
bu
3 Bridge excitation
voltage
120 to
1000
Ruser
13
3 Sensor circuit
Rshunt
11
Ruser =
Shunt connection
RS/G
3.2
D-17
Inductive transducers
15-pin socket
1
9
1 Measurement signal
15
4 Measurement signal
2 Bridge excitation
voltage
3 Bridge excitation
voltage
13
3 Sensor circuit
12
2 Sensor circuit
Spider8
D-18
1
9
15-pin socket
bk
bu
gn
gy
1 Measurement signal
15
4 Measurement signal
2 Bridge excitation
voltage
3 Bridge excitation
voltage
13
3 Sensor circuit
12
2 Sensor circuit
Spider8
3.3
D-19
DC voltage sources
2 1
5-pin socket
mounted
terminal connector
Ue
Ground, potential-segregated
Ue
"10V
15-pin socket
1
9
15-pin socket
+
-
Ue
Zero operating voltage
(ground)
4
14
Ue
"10V
Spider8
D-20
5 4
2 1
5-pin socket
mounted
terminal connector
0 . . .+20mA
Ii
Ground,
potentialsegregated
1
-
Supply voltage
Spider8
+ Ii
3.4
D-21
DC power sources
5 4
2 1
Ii
Ground,
potentialsegregated
1
+
20mA; 200mA
RL = 5
Ii
Spider8
D-22
3.5
Resistors
5 4
2 1
5-pin socket
mounted
terminal connector
Spider8
Current feed
Measurement signal +
Measurement signal
Ground
3.6
D-23
Potentiometer
15
15-pin socket
9
wh
bk
bu
gn
gy
1 Measurement signal
2 Bridge excitation
voltage
3 Bridge excitation
voltage
13
3 Sensor circuit
12
2 Sensor circuit
Spider8
D-24
3.7
Thermocouples
2 1
mounted
terminal connector
Temperature range
Type J
Fe/Cu-Ni
-200...+1000
Type K
Ni-Cr/Ni
-200...+1360
Type T
Cu/Cu-Ni
-200... +400
Type S
Pt-10%Rh/Pt
0... +1700
+ Ui
Ui
Ground, potentialsegregated
Note:
The thermocouple (extension wire) must continue up to the
connector.
The inherent errors of the 100mV measuring range should be taken
into account when examining errors.
Spider8
D-25
Example:
SR01:
200V error
4V
Thermocouples J, K, T:
Resolution max.:
Error:
0.1C
2.5C - 5C
Thermocouple S:
Resolution max.:
Error:
1C
25C - 50C
Extension wires
+
-
5-pin terminal
Thermocouple
+ Ui
2
1
- Ui
Ground, potentialsegregated
Thermal
reference element in iced
water at 0oC
Spider8
D-26
3.8
8
15
15-pin socket
1
9
Metering pulses 1
10
Direction
or metering
pulses 2 (90o
offset to 1)
2
4
3
Clear
+5V
10k
INA
+5V 10k
INB (High)
+10V
Ground
+5V
10k
Clear (Low
active)
Shield
forwards
backwards
max. "20V,
Switching threshold High u2.5V, Low t2V
u850s
Connecting Connecting a PC
D-27
Connecting a PC
4.1
PC requirements
Recommended PC configuration:
D MS Windows 3.1 or MS Windows for Workgroups
D CPU: 80486
D 8MB RAM
D hard disk space for program installation
Setup:
5MB
20MB
Spider8
Connecting Connecting a PC
D-28
13
13
Connecting Connecting a PC
4.2
D-29
Printer port:
IEEE1284 cable only
13
13
13
NOTE:
With the first Spider8, switching
on lights up the power indicator.
With every subsequent Spider8
the power indicator flashes until
communication is established with
the computer.
Spider8
Connecting Connecting a PC
D-30
4.2.1
Spider 8-30
13
Spider 8-30
13
Spider8
NOTE
If you already have a Spider8(SR55 module) and want to
operate it together with a Spider8-30(SR30) in mixed
operation, you must also load the new Spider8-30
software on the Spider8.
Spider8
D-31
Connecting a printer
Printer
Parallel interface
Printer cable
13
Spider8
D-32
Spider8
E-1
Spider8
E-2
Spider8
E-3
Setup program
The setup program simplifies the way you operate the Spider8.
With this program you can
When you have configured your device, you can save the settings
and recall them at a later time.
Mouse actions:
Mouse actions are the basis for all functions concerned with the
direct manipulation of objects in the graphic user interface.
Actions:
Click:
Single click:
Spider8
E-4
Start setup*:
with a double-click. This starts the setup program. You are now
in the setup dialogue.
To see which settings can be displayed and changed, refer to
Chapter 1.1
Spider8
1.1
E-5
Enter device
name
Select interface:
OFFLINE
COM1
COM2
LPT1
LPT2
OFFLINE
parallel
PC interface
serial
PC interface
E-6
COM1:
COM2:
GPIB:
LPT1:
LPT2:
Serial interface
Serial interface
IEC interface (not provided for Spider8)
Parallel port
Parallel port
Once you have chosen your settings and confirmed them with OK,
(the correct interface settings for the Spider8 have already been
made and do not usually need to be changed), you will again see
the illustration shown on Page E-5.
Spider8
E-7
Stop bits
Data bits
E-8
Byte mode:
Transfer from the Spider8 to the PC takes place via data lines,
which are switched from the normal direction (output) to input
(two-way operation) in order to do this. Most modern computers
allow this type of programming.
Data transfer rate: 48 000 bytes/s (24 000 samples/s)
EPP mode:
If the interface is working in EPP mode, the data is transferred
bi-directionally, as in byte mode. Handshaking is also handled
directly and therefore very quickly, whereas with all other operating
modes, the processor deals with handshaking using the program. It
is important here whether several Spider8s are cascaded and how
many channels are activated.
Data transfer rate: > 152 000 bytes/s (76 000 samples/s)
All throughputs mentioned are values determined in experiments
using large data quantities on a 486 PC with a clock-speed of
33MHz. More up-to-date computers with faster clock speeds can
achieve considerably greater data throughput, especially in Nibble
and Bit8 operating modes.
Often the BIOS setup (accessible by pressing a key during boot-up)
or a manufacturer-specific setup program will offer you the option of
configuring the parallel ports.
Spider8
E-9
NOTE
If you adjust the BIOS setup, you must save the new
version. This setup will not become active until you
boot up the hardware.
Spider8
E-10
You are now in the setup dialogue. All settings are entered in the
setup program using the cursor (mouse pointer).
Spider8
Configuring the Spider8 with the Setup program Description of the setup dialogue
1.2
E-11
Mark Chan. Name Trans. Meas. Rng. Filter Tare Shunt Tare Val. Meas. Value
There are various types of boxes that you can use for setting up the
functions mentioned in the selection bar:
List boxes:
List boxes are displayed for transducer, measuring range and
filter functions. A list box offers you a list of items from which to
choose.
Spider8
E-12
Configuring the Spider8 with the Setup program Description of the setup dialogue
1
2
3
Name
Trans.
Meas. Rng.
1.
3mV/V
33mV/V
12mV/V
125mV/V
500mV/V
2.
2. Move the cursor to the 12mV/V setting in the list box and press
the mouse-button. The value 12mV/V is outlined.
Chan.
1
2
3
Name
Trans.
Meas. Rng.
12mV/V
Spider8
Configuring the Spider8 with the Setup program Description of the setup dialogue
E-13
Text box:
A text box is displayed for the function Tare value. A text box
consists of a rectangular area distinguished from the surrounding
area by a different background colour. A text box is where you type
data (maximum two lines, 20 characters) that cannot be presented
for selection in list form.
Example:
You want to enter a tare value for channel 3.
1. Click on channel 3 under the Tare Val. function.
A blank, one-line box is displayed.
Mark
Chan.
Name
Trans.
Meas. Rng.
Filter Tare
1
2
3
1.
Chan.
Name
Trans.
Meas. Rng.
Filter Tare
1
2
3
1.
0.50000
3. Confirm your entry with the Return key.
Spider8
E-14
Configuring the Spider8 with the Setup program Description of the setup dialogue
Option boxes:
Option boxes are displayed for the functions Tare and Shunt. An
option box lets you choose one of several alternative options
(Yes/No).
Select status:
This status shows that an option is active. A tick is displayed in the
option box
3.
Deselect status:
This status shows that an option does not apply. There is no tick in
the option box.
Example: Tare option box
The channel is to be tared.
1. Click on channel 3 under the Tare function. There is no tick in
the box.
Mark
Chan.
1
2
3
Spider8
Name
Trans.
Meas. Rng.
Filter Tare
Configuring the Spider8 with the Setup program Description of the setup dialogue
E-15
Buttons:
A button is a rectangular graphic element with a three-dimensional
appearance. A button is activated by selecting it with the
mouse-button. In the case of a button, the action is not executed
until you release the selection button on the mouse whilst the
pointer is still on the screen button.
Example: Zero balance
Zero balance
By clicking on the Zero balance button, all channels which are
selected in the Tare column are zeroed. In the case of buttons
which have three dots after the label, a new dialogue appears (e.g.
Test Device...).
Spider8
E-16
Configuring the Spider8 with the Setup program Description of the setup dialogue
b.
Menu bar
File
Edit
Device
Options
Help
File
Load Setup
Save Setup
Save Setup As
Print Setup
Quit
Load Setup:
Spider8
Configuring the Spider8 with the Setup program Description of the setup dialogue
E-17
Spider8
E-18
Configuring the Spider8 with the Setup program Description of the setup dialogue
File
Edit
Undo All Settings
Select All Channels
Deselect All Channels
File
Edit
Device
Add
Remove
Spider8
Configuring the Spider8 with the Setup program Description of the setup dialogue
E-19
File
First Spider8:
Second Spider8:
Edit
Device
Channel 0...8
Channel 10...18
Options
Logfile On
Show Logfile
Delete Logfile
Logfile On:
The whole communication between the setup program and the
Spider8 is recorded. If this menu item is selected again,
recording is stopped.
Show Logfile:
The log can be read.
Delete Logfile:
File
Edit
Device
Options
Help
Contents
Spider8
E-20
1.3
Configuring the Spider8 with the Setup program Description of the setup dialogue
Mark channels
1.
Chan.
Name
Trans.
Meas. Rng.
1
2
3
2.
Spider8
3
3
3
Chan.
1
2
3
Name
Trans.
Meas. Rng.
Configuring the Spider8 with the Setup program Description of the setup dialogue
E-21
1.
Chan.
Name
Trans.
Meas. Rng.
1
2
3
4
5
6
3
2.
3
3
Chan.
Name
Trans.
Meas. Rng.
1
2
3
4
5
6
Spider8
E-22
Channel-specific menus
Setup dialogue
x
Program version
Current file
Selection bar:
The selection bar shows you the functions necessary for setting up
the Spider8. Functions will be explained from left to right (each in
turn shown on a grey background). In addition you need the
device-specific functions for setting up (see page E-30).
Mark Chan. Name Trans. Meas. Rng. Filter Tare Shunt1) Tare Val. Meas. Value
Chan.
0
1
2
3
4
5
6
7
8
Spider8
NOTE:
blank
SR55
SR01
SR30
1)
E-23
Name:
Shunt
Spider8
E-24
2
3
4
5
6
7
8
Carrierfrequency
module
(SR55):
Full bridge
DC
V
Carrierfrequency
module
(SR30):
DC voltage
Signal edges
DC voltage
Signal edges+
direction
+
-
Half bridge
2 phases, 1x
Quarter bridge
DC
V
DC
C
J
K
T
S
PT
100
I / O:
Half bridge
Full bridge
DC
module
(SR01):
Full bridge
Half bridge
DC
Spider8
Chan.
0
1
Shunt
IOIO
OIOI
DC voltage
2 phases, 4x
DC voltage
DC current
Resistance
Thermocouple J
Thermocouple K
Thermocouple T
Thermocouple S
PT100
PT500
PT1000
*
No selection available
E-25
Explanation:
Signal edges:
If only 1 signal is measured, one signal edge is counted.
Signal edges and direction:
If 2 signals are measured: the first channel measures pulses (one
signal edge), the second channel defines the direction (ascending
or descending).
2-phase, single interpretation:
If two signals are measured, one edge of one signal is interpreted.
The phase position defines the direction.
2-phase, 4-fold interpretation
If two signals are measured, both edges of each signal are
interpreted. The phase position defines the direction.
Spider8
E-26
Shunt
Measuring range:
The available measuring ranges are displayed in accordance with
the transducer selected.
Transducer
Full bridge
Half bridge
Meas. Rng.
3mV/V
12mV/V
125mV/V
500mV/V
Quarter bridge1)
DC voltage
Signal edges
Signal edges + direction
2 phases, 1x
2 phases, 4x
1)
Spider8
Chan.
0...3; 4...7
(SR55, SR30)
10V
1MHz
100kHz
10kHz
1kHz
10ms
100ms
1s
10s
100s
Cnt
Cnt/100
Channel 0 and
1 only
E-27
Transducer
DC voltage
Shunt
Meas. Rng.
0.1V
1V
10V
Chan.
4...7 (SR01)
DC current
20mA
200mA
4...7 (SR01)
Resistance
400
4000
4...7 (SR01)
Thermocouples
J, K, T, S
0.1V
4000
4...7 (SR01)
4...7 (SR01)
Spider8
E-28
Filter:
Shunt
Tare:
Shunt
Shunt1)
Shunt
1)
Spider8
Tare value:
0.00005
E-29
Shunt
Measured value:
9.3486
Shunt
e.g. 2505
9C9
00001001
11001001
Select the required bit with the mouse pointer and click the
righthand mouse-button. Then 0 becomes 1 and vice-versa.
Spider8
E-30
Device-specific menus
Device: Spider8
Sampling Rate
Zero balance
Test Device...
600
20Hz
Zero balance:
Zero balancing is carried out for all channels where Tare has been
selected.
1. Click on the Zero balance button
The new zero balance values are displayed in the Tare value
column. The zero balance value is subtracted from the current
measured value. This means that the measured values are more
or less equal to zero after a zero balance.
Spider8
E-31
Test Device:
<<<
>>
Help
OK
Spider8
E-32
Samplingrate:
The amplifier modules deliver measured values with a data transfer
rate of between 1 and 9600 measured values/s. Depending on the
sampling rate chosen, different filter frequencies are available for
selection. If the current filter frequency does not match the newly
chosen sampling rate, the next feasible filter frequency is
automatically set up. The filter type is therefore decisive (see table
on page E-34).
A selection of the available sampling rates:
Sampling Rate
9600
600
800
1200
Spider8
Impulse response
E-33
Filter Frequency:
The available choice for the filter setting depends on the measuring
rate selected.
A selection of the available filter frequencies:
20Hz
10Hz
5Hz
2.5Hz
1)
2)
Adjustable filter
Fixed filter
Spider8
E-34
The following table shows the choice of filter frequencies for the Spider8 and the
Spider8-30.
Sampling rate as a function of cutoff frequency:
see example on following page
Cutoff frequency fg (Hz)
1200
600
300
150
(x)
(x)
(x)
(x)
(x)
3200
(x)
2400
(x)
1600
1200
800
600
9600
4800
75
40
20
10
400
300
2.5
0.5
0.25
200
150
100
75
60
50
25
10
5
2
1
0.1
E-35
If you change the sampling rate, what effects does this have on
the filter frequency?
1. If possible, the filter frequency selected during set-up is used.
2. If this is not possible, the filter frequency is modified by as little
as possible when compared with the frequency last used (see
fields in table on previous page).
Example: Selected frequency 150Hz
Change in sampling rate:
Sampling Rate
25 /s
Selected filter
2.5Hz
800 / s
10Hz
1200 /s
20Hz
Spider8
E-36
Spider8
Specifications
F-1
Specifications
Series
Accuracy class
Spider8 / SR55
Spider8-30 / SR30
Spider8-01SR01
0.2
0.1
Digit
"25000
Measurement buffer
Meas
< 20000
Meas/s
Meas/s
Meas/s
Meas/s
-
1/s
1...9600
Digital filter
Aperiodic
Average value
Butterworth (4th order)
Bessel (4th order)
Hz
Hz
Hz
Hz
0.1
Sampling rate/8 to sampling rate/4
0.1...200
0.1...200
Baud rate
serial
parallel1)
USB
Nibble mode
8Bit mode
Byte mode (two-way)
EPP mode
see data sheet USB
Number of amplifiers
Transducers that can be connected
0.1...1200
0.1...1200
0.1...1200
0.1...1200
4/1
4/1
DC voltage sources
DC power sources
Resistors
Thermocouples
mA
Vrms
0.25
2.5
4800
Hz
Transducer resistance
Compensating resistors
mV/V
50
200
50
Pulse/frequency
2-phase transmitter
600
110...1100
Spider8
Specifications
F-2
Series
Measuring ranges
S/G / Ind. transducer
Voltage
max. differential input voltage
max permissible common-mode voltage
(differential voltage input-groung)
input resistance
Current
Resistance
Frequency2)
Period length2)
Counter2)
Spider8 / SR55
M
mA
1
"20; "200
400; 4000
kHz
s
d
%
%
-10...+50
-20...+60
-20...+70
Supply voltage
Power consumption
Connections
Transducer
Digital I/O
RS-232 computer interface
Printer port
PC interface
0.05
0.1
0.1
0.2
11.8...15
4 / 0.25
mm
Weight
Spider8
Spider8-01/SR01
mV/V
V
V
V
Dimensions (W x H x D) Housing
2)
Spider8-30 / SR30
0.8
330 x 75 x 270
kg
2.75 / 0.05
0.05
DB-15 socket
DB-15 socket
SUBCON 5-pin
socket
DB-25 socket
DB-9 socket
DB-25 socket
DB-25 socket
Specifications
F-3
D0012367 78-084-1300
Device input
Input voltage Ui
110...250
Frequency range
Hz
50 ... 60
approx. 0.4
approx. 0.2
< 30
approx. 82
EMV requirements
Dynamic mains undervoltages with any notch depth and any notch duration can lead to the switching off of the device, but not to its
destruction.
Spider8
Specifications
F-4
Device output
Nominal voltage
set to adjustment accuracy
Accuracy
V
V
%
12
12 "1%
"5
< 100mV pp
Ripple (100Hz)
Amplitude
Rated current
1.6
Accuracy
"5
Device connection
Switching on
Fuses
Dimensions (H x W x L)
mm
IP20
Degree of protection
KS
Noise suppression
Stray current
Note
Spider8
56 x 68 x 116
1 according to EN 60950
Protection class
mA
<3.5
The device is designed with an intermediate DC circuit at the input. The
filter capacitor of this circuit acts as a buffer when the mains supply is
switched off. However, if you open the device up, you must be aware
that the input circuit still carries over 100V DC for some time after the
mains voltage is switched off.
Keyword index
G-1
Keyword index
Spider8
Keyword index
G-2
A
adapter cable, D-7
add device, E-18
B
basic version of the device, B-5 , C-3
blank plates, C-3 , D-5
buttons, E-15
C
carrier-frequency module, D-5 , D-7 , D-19 , D-23 ,
E-24
catman, C-7
channel, B-3 , D-5
selecting, E-18
computer, B-6
D
DC module, D-10 , D-19 , D-20 , D-21 , D-22 , E-24
DC power sources, D-21
DC voltage sources, D-19
digital I/O, B-3 , E-29
digital inputs, B-11
DLL program, A-4
E
EMC protection, D-3
Spider8
ERROR, B-16
F
factory settings, B-10
filter, E-28 , E-33
filter frequency, E-32
filter type, E-32
Firmware, A-4
update, C-3
four-wire connection, D-9
G
Greenline, D-3
H
help, E-31
Keyword index
G-3
PC configuration, D-27
PC/Master, B-3
phase, E-25
installing
modules, C-3 , C-4
Software, C-7 , D-30
potentiometer, D-23
L
LEDs, B-15 , B-16B-19
list boxes, E-11
logfile, E-19
M
measured value, E-29
measuring range, E-12 , E-26
mixed operation, D-30
modules, C-3
carrier-frequency, DC, D-5
R
remove device, E-18
resistor, D-22
RS-232-C, B-3 , B-6 , B-9
S
S/G full bridge, D-11
S/G half bridge, D-12
sampling rate, E-32
O
offline mode, E-11 , E-22
online mode, E-11 , E-22
option box, E-14
Spider8
Keyword index
G-4
thermocouple, D-24
transducer
DC current, D-6 , D-21
DC voltage, D-6 , D-19
Frequency, counter, D-6 , D-26
Inductive full bridge, D-6 , D-17
Inductive half bridge, D-6 , D-18
Potentiometer, D-6 , D-23
Resistance, D-6 , D-22
S/G full bridge, D-6 , D-11
S/G half bridge, D-6 , D-12
S/G quarter bridge, D-6 , D-13 , D-14 , D-15 , D-16
Thermocouple, D-6 , D-24
T
tare, E-28 , E-29
taring, E-28
terminal block connector, D-10
Spider8
trigger, B-11
Z
zero balance, E-30
Declaration of conformity
H-1
Declaration of conformity
Spider8
H-2
Spider8
Declaration of conformity
Declaration of conformity
H-3
Spider8
H-4
Spider8
Declaration of conformity
HBM
Modifications reserved.
All details describe our products in
general form only. They are not to be understood as
express warranty and do not constitute any liability
whatsoever.
B0405-7.0 en