Professional Documents
Culture Documents
Test Series Paper Ii
Test Series Paper Ii
PAPER II
SET 1
1. In digital multimeter, setting is:-
(a) Low (b) Shunt is used (c) Zero (d) High resistance
2. To increase range of Ohm meters to measure high voltage required internal resistance to be:-
(a) Low (b) High (c) Constant (d) Balance with deflection of probes
4. In capacitor charging, if key is open and if distance between plates is increased, then
(a) Capacitance decreases (b) Capacitance increases
(c) P. D. increases (d) P. D. decreases & stored
7. MCS :-
(a) Zener diode used for as amplifier (b) Tunnel diode used for voltage regulator
(c) As in ((b), and as an oscillator (d) Iaraetop diode is used for switching circuit & electronic tunner
14. MCS:-
(a) Cold water quenching minimize distortion & cracks.
(b) Hot water quenching minimize distortion & alienates cracks.
(c) Spray quenching reduces the wear and corrosion.
(d) Cooling at room temp.
15. Heat treatment of Al. alloys and after it allowed to cool for 4 to 5 days is
(a) Natural ageing. (b) Artificial ageing. (c) Both (a) & (b) (d) Room temp. of alloys.
18. Most important factor which affects the indication of dye penetrant inspection check is:-
(a) Not proper application of Dye (b) Not proper application of penetrant
(c) Parts are not thoroughly degaussed & cleaned (d) All of the above
41. MCS
(a) Roller bearings take thrust load. (b) Radial bearings are used for shaft, gears etc.
(c) Ball bearings with stand heavy radial loads (d) All above correct
42. While demagnetize the parts:-
(a) By passing sufficient A.C. into the field. (b) By passing a.c. slowly out to the magnetic field.
(c) By repeatedly apply a.c. over the part (d) Increasing the strength of magnet then cutout a.c.
48. MCS
(a) Corrosion on Al., have etching and pitting (b) Corrosion on Cu., have greenish film
(c) Corrosion on Mg., have etching and pitting (d) All are correct
54. MCS
(a) QNF, atmospheric pressure reads zero.
(b) QNH, barometric pressure above elevation at meansealevel
(c) QNE, barometric pressure at altitude (d) Both (b) & (c) are correct
62. Algorithm is
(a) finite and definite steps and must have output (b) finite steps and output is not necessary
(c) having output only (d) none of the above
63. UNIX is
(a) multi operating system (b) single operating system
(c) utility software which may be used by many users (d) software
66. In ATA code system, electrical wires are identified by number & letters with
(a) by left side & right side (b) by suffix and prefix
(c) both (a) & (b) (d) by bottom no.
70. How can you distinguish between heat treated metal or non heat treated metal
(a) By using 10% caustic soda solution (b) By using 5% cupric solution
(c) by Rockwell tester (d) by using 10% of muriatic acid in 1% water solution
72. If a bulb utilizes power of 28 watt and given voltage is 28 volt than resistance offered in ckt will
(a) 28 (b) 1 (c) 28 A (d) 28 watt
73. In Triode
(a) grid, plate, heater (b) cathode, plate, heater
(c) heater, grid, cathode (d) cathode, heater, plate and spiral wire between plate and cath
74. In a circuit if C = coulomb, W = weber, A = amp, S = second and V = volt than relation will
(a) W S-1 ~A (b) W S ~V (c) W S ~C (d) W S-1 x V
75. In electricity, a parallel circuit is there, what will be the correct statement
(a) Sum of the different current in each path will equal to the total current
(b) Potential difference across each path will be different
(c) Both (a) & (b) (d) Current will be same in each path.
78. In Pitot static system, the static vent is of the flat plate tube used anywhere in the a/c structure to prevent
(a) Position error (b) Instrument error
(c) Protection against ice formation (d) Both (a) & (c)
80. In Ni Cd battery if potassium carbonate is formed on the plate, the main reason behind that
(a) Battery is over charged (b) Good battery ventilation
(c) High internal resistance (d) High electrolyte level
81. In drill sizes No: 1 size
(a) Is smaller than A (b) Is greater than Z
(c) Is smaller than I/64 (d) None
85. In altimeter system, static vent is disconnected from pressurized cabin then
(a) Altimeter read more (b) Altimeter & A.S.I. will read low
(c) Airspeed will read more (d) Both (a) & (c)
89. Mark the correct statement in case of flare less rubbing, should not tighten the nut
(a) Not more than 1/3 turn after resistance is felt (b) Not less than 1/3 turn after resistance is felt
(c) Not more than 1 turn after resistance is felt (d) None
94. In tubing has a diameter from to 5/16 then support should be at distance
(a) 9 (b) 12 (c) 16 (d) 22
102. In oxy hydrogen and oxy acetylene, temperature of oxy hydrogen will be
(a) more (b) less (c) equal (d) unpredictable
108. In a metric micrometer main scale has crossed 2 graduation and O thimble scale has hundred graduation and
Ordinary scale 45, division will be matched with zero line
(a) .001 cm and .245 cm (b) .001 cm and 2.45 cm
(c) .01 cm and 2.45 cm (d) .01 cm and .245 cm
109. Mark the correct statement
(a) Intergranular corrosion may be remove by mechanical means
(b) Intergranular caused due to improper heat treatment
(c) it is a surface corrosion (d) none
110. Too much pressure of clamps on the flexible hose will cause
(a) cold flow (b) hot flow (c) rinkles (d) both (a) & (b)
112. Which of the following factors is considered basic knowledge of X ray exposure
(a) the density, thickness, size and shape of the objects to be exposed
(b) the type of X ray machine used & hazards
(c) the distance and angle for 10 minutes exposure
(d) the type and exact size of the discontinuity to be detected.
114. If two current carrying conductor spaced at a distance of 2 cm and current is 2 amp force will be
(a) attractive if current is following in same direction
(b) attractive if current is following in different direction
(c) attractive if A C is following in one of the conductor (d) both (a) & (c)
117. Exfoliation is
(a) extreme case of Intergranular corrosion (b) more harmful of Intergranular attack
(c) it occurs along the grain boundaries, under thin oil, grease or varnish film (d) both (a) & (c)
118. How can you remove a swaged fitting
(a) drill out by the one gage small bit (b) prick out by a drill punch
(c) unscrew the thread insert (d) all of the above
120. Which of the following occurs along the lines of cold working and may be triangular & Intergranular in
nature
(a) stress corrosion (b) surface corrosion (c) Intergranular corrosion (d) electrochemical corrosion
126. If you have same 17S rivets of diameter, you should use in construction
(a) within 10 to 20 minutes after aging (b) should not use after 5 hour aging
(c) can be drive within one hour before they have age hardened
(d) should not used after age hardening
127. Mmicrometer reading with tur error metric micrometer have .01 least count & +ve error is .02
(a) (b) (c) (d)
139. Nome is a
(a) honey comb. material (b) reinforced fibre (c) metrix material (d) none
142. In a dye penetrant test before applying developer what shall be done
(a) dye should be completely flushed out (b) only excessive dye should be removed
(c) the rinsing operation is completely carried out (d) both (b) & (c)
143. Which one is the correct statement regarding heat treatment of AL alloy
(a) longer soaking time & lower pooling rate result in a greater softness
(b) longer soaking time & higher pooling rate result in a greater softness
146. Which of the following statements are associated with the term fillet
(a) space between the teeth (b) a bounded surface to eliminate sharp corner
(c) (d)
153. Which of the following rivet does not require heat treatment
(a) 2017 (b) 2117 (c) 2024
168. Thermiator
(a) rom temp. coefficient (b) variable temp. coefficient
(c) + ve temp. coefficient (d) - ve temp. coefficient
173. If the bar magnet in the fig. will be removed shown the electromagnetic induction will be
(a) oppose the emf (b) act in same direction (c) will not repot but attempt
179. In a blind revet the length between manufacture head in the end is
(a) grip length (b) grip range (c) shank length of the revet
181. In a bolt and nut assembly after applying treque, cotter pin hole is not aligning the bolt may be
(a) slightly tightened to next slot. (b) slightly loosened to next a slot (c) washer
184. Unless specified the troque to be applied to a bolt and not assembly should
(a) degresed dry and clean thread (b) lubricated thread
188. Gyroscope the phenomena which causes continuous spin of outer ring due to coincidence of rotor ring with
Cuter gimble ring axis is called
(a) gyro wander (b) gyro tambling (c) apparent precession (d) gimble lock
196. Micron is
(a) millionth of meter (b) thousandth of meter
201. Least count of 50 divisions on the circle of micrometer whose pitch is 1 min
(a) 0.01 mm (b) 0.02 mm (c) 0.5 mm (d) 0.002 mm
206. Which of the following is not contained generally in aircraft specification type data sheet
(a) empty weight of the aircraft (b) useful load of A/C
(c) payload of A/C (d) control surface movement
217. Which one of the following is boots self locking nut figure
(a) (b) Elastic Anchor Nut (c)
230. If the temperature of a confined liquid is held constant and the pressure tripled, the volume will be
(a) triple (b) be reduce to 1/3rd original (c) remain the name (d) none
240. A fibre type, self locking nut must never be used on an a/c if the bolt is
(a) under shear loading (b) under tension loading
(c) both tension and shear loading (d) subjected to rotation
243. A particular component is attached to the a/c structure by the use of an a/c bolt and a castleted tension nut
combination. If the cotter piarole does not align with the recommended torque. A acceptable practice is
246. Oxyacetylene flame with equal volume of oxygen and acetylene gives the types of flame as shown
(a) carbonzing (b) oxidizing (c) neutral (d) there is no such flame
248. The most commonly used symbols for electromagnetic flow direction method is
(a) UFD (b) MFD (c) PFD (d) EFD
249. In oxyacetylene welding it is better prentice while shutting off the flame
(a) Shut off oxygen first (b) Shut off acetylene first
(c) Turn off the regulator (d) Turn off simultaneously
250. The silver sol deny metal melts at
(a) 200 400 degree cent (b) 600 to 850 degree cent (c) 1000 1600 degree cent
255. T4 & W are the symbols utilized for heat treatment of Al alloy sheet indicates
(a) solution heat treated only (b) solution heat treated & quenched but not aged
(c) precipitation heat treated (d) solution heat treated
264. Taking all the factors into consideration the most commonly used metal as electrical conducting
(a) aluminum (b) copper (c) silver (d) iron
266. In ATA coding system the size and type of the electrical cables/wires in a/c are given by:
(a) prefix and suffix (b) side by side (c) numbers and letters (d) none of the above
269. 13 NC B indicates
(a) pitch diameter (b) B external thread
(c) 13 NC indicated 13 TPI and have antiqnal form (d) all
270. In gear system a driver and driven on the shaft to get the name direction of notation
(a) bevel gear is used (b) internal and external gear combination is used
(c) as in a and no mechanical advantage is obtained (d) none
272. To bring the sheet together to get air tight joint, we use
(a) draw set (b) cleco fastener (c) aligning camp (d) none
285. Heat treated parts having bake dirt and scale can be cleaned
(a) wire brush (b) scraping (c) sand blasting (d) none
286. Pre & past treatment of cd plating and ferros part depends on
(a) strength of part (b) surface hardening and hard spots
(c) corrosion resistance (d) all
289. In brazing
(a) post heat treatment may be carried to relive stresses
(b) post heat treatment may not be carried to relive stresses
310. The thickness of the conducting and nor conducting coating in ferrous metal can be measured by
(a) varies coliper (b) varnier micrometer (c) ultrasonic (d) eddy current method
311. To measure the thickness of the hollow tubular member normally done by
(a) distructive method (b) eddy current method (c) ultrasonic method (d) none
321.
(a) How many types of corrosion forms on
(b) What are the factors which affects the corrosion?
(c) How preventive measures can be taken to prevent the formation of corrosion the a/c?
330. When material is forced through a die to take the shape of die, is called
(a) Forging (b) Rolling (c) Extrusion (d) Casting (Mg)
331. All long extruded parts such as bar, tube, pipe etc are stored
(a) horizontally (b) horizontally with well supported along its length
(c) vertically inclined at an angle of 600 (d) all
336. The part which is dry and un lubricated, which of the following occurs
(a) erosion (b) abrasion (c) fettlers (d) all
337. In radiography NDT, which of the following factor does not affect the test
(a) distance of film and exposure angle (b) time
(c) material thickness, density, shape & size (d) film characteristic
340. The sketch giving the description of object made up of two or more parts
(a) detail drawing (b) assembly drawing (c) installing drawing (d) none
346. As per ATA 100 specification, the correct sequence of air conditioning, fuel, navigation and oil system is
(a) 21,28,34,79 (b) 21,34,28,79 (c) 31,34,52,80 (d) 32,28,34,79
349. Axial distance covered by a threaded fastener in one complete revolution is called
(a) pitch (b) lead (c) bolts (d) none
352. In engineering drawing, the lines indicate the alternate position of parts or relative position of a missing part
(a) hidden line (b) phantom line
354. What amount of load is acting on the bolt f extension bar is used on the torque wrench as shown in figure
(a) 150 lbs (b) 125 lbs (c) 175 lbs (d) 200 lbs
362. (0.0625)10 = ( )2
(a) 0.110 (b) 0.101 (c) 0.011 (d) 0.100
373. In 7075
(a) annealed (b) strain hardened (c) solution HT (d) none
380. Al alloy is not heat treated properly to have uniform grain boundaries it has
(a) stress corrosion (b) galvanic corrosion (c) inter granular corrosion (d) fretting corrosion
382. Which is used to transfer rivet size from template to new sheet is
(a) centre punch (b) pin punch (c) alignment punch (d) transfer punch
383. A side clearance between piston ring and cylinder wall is measured by
(a) telescopic gauge (b) thickness gauge (c) micrometer (d) plug gauge
387. In magnetic particle inspection, nickel plating does not give indication of
(a) crack (b) discontinuities (c) corrosion (d) none
388. In dye penetrant inspection, the defects under while light appears
(a) black (b) green (c) red (d) all
391. In ultrasonic test, when mechanical stress vibration is applied to crystal quartz then these are
(a) electrical energy and voltage are produced (b) more vibration are produced
(c) as in (a) and varies with the thickness of crystal (d) none
392. Form of corrosion which occurs between metal and nonmetal is
(a) filltform corrosion (b) crevice corrosion (c) exfoliation corrosion (d) fretting corrosion
396. For maximum elongation, ductility, tensile strength and impact resistance Mg alloy is
(a) solution heat treatment (b) casted (c) precipitation heat treatment (d) none
399. An ac circuit consists of inductance of 10, capacitance 4 & resistance 8 the impedance of the circuit is
Z = R2 (XL XC)2
(a) 6 (b) 10 (c) 5.5 (d) 8
404. The static vents with the flat surface plate at two positions to
(a) minimize position error (b) have is formation freedom (c) both a & b (d) none
406. An ac circuit has inductance 3 and resistance of 4, then impedance of the circuit is
(a) 3 (b) 1 (c) 5 (d) 7
410. Mg is
(a) Susceptible to corrosion (b) Has tendency to crack (c) Resistance to corrosion (d) Both a & b
413. Rack is mesh with a gear, it is used to change (the purpose of rack and pinion is to change)
(a) rotary motion to reciprocating motion (b) reciprocating motion to rotary motion
(c) both a & b (d) none
420. Heated treated and non heat treated metal 25, distinguished by
(a) magnetic particle inspection (b) eddy current test (c) dye penetrant inspection (d) ultrasonic test
438. The modulation in which, amplitude is kept constant and frequency is changed is called
(a) amplitude modulation (b) space modulation
(c) frequency modulation (d) phase modulation
440. In NDT of material by Dye penetrant inspection (DPI) the volume of defect is interpreted by
(a) Staining rate (b) Staining speed (c) Staining extend (d) All
441. In UST, scanning is carried out by moving both probes simultaneously in opposite direction for
(a) flash butt joint (weld) (b) heavy forgings
(c) heat treatment defect (d) thickness measurement
443. The fluid use for all types of aircraft engine except rocket is
(a) gasoline (b) air (c) ATF (d) All are correct
444. In a composite repair the part is steeped rather than to be scrafed for
(a) uniform shear stress (b) uniform tensile stress (c) smoothness (d) both a &b
446. In uniform fluid flow, the fluid is first made to flow through a tube and the pressure exerted by the fluid is
measured by
(a) dynamic pressure (b) static pressure (c) reynolds no. (d) all
448. The rust and corrosion is removed from highly stressed steel parts by
(a) abrasive paper (b) fine buffling cloth on buffling wheel (c) wire brush (d) all
455. In magnetic and non magnetic material, coating thickness of ferrous and non ferrous alloy should be
measured by
(a) eddy current (b) magnetic particle test (c) micrometer caliper (d) all
461. When two surfaces fit tightly together, but can move relatively to one another
(a) fretting corrosion (b) intergranular corrosion
482. A device which gives latest control and is mounted at the opposite surface of wing
(a) spoiler (b) vertex generator (c) tab (d) flap
489. Which of the following precision instrument issued for lightening the nut on bolt with proper torque is
(a) socker wrench (b) torque wrench (c) ratchet wrench
490. For repairing the oversize hole with sleeve, the hole must be drilled oversized by
(a) 3/16 (b) 1/32 (c) 1/64 (d) 3/64
495. What type of battery charger is recommended for final charging of a Ni cad battery
(a) constant current charger (b) constant voltage charger (c) both a & b (d) any one of the above
500. T6 indicates
(a) artificially aged only (b) SHT and cold worked
(c) SHT and their artificially aged (d) Solution heat treated
502. A micro switch will open or close a circuit with the movement of
(a) 1/16 or less (b) 1/16 or more (c) both (d) none
510. Instrument panels are usually shock mounted to absoro ------ shock
(a) low frequency, high amplitude (b) high frequency, high amplitude
(c) low frequency, low amplitude (d) high frequency, low amplitude
519. While starting the piston engine, which type of fire extinguisher is permitted
(a) water and water based agent (b) Co2 + 516 capacity
(c) Dry chemical (d) CC14 (halon gas)
523. In PFD, when used fluorescent, material color of defective part and sound part is
(a) brilliant yellow green and blue violet (b) brilliant yellow green and bright red
(c) bright red and blue violet (d) none of the above
524. ATA 100 code of hydraulic power, pneumatic, fire and engine oil is
(a) 36,26,79,83 (b) 29,36,26,78 (c) 29,36,26,79 (d) 79,36,29,26
531. If no marking of drill, identification of drill can be measured by drill gauge having
(a) fraction on right and no on left (b) fraction on left and no on right
(c) both a & b (d) none of the above
538. What size of the hole should be bored before cutting a 2.5 internal acme thread having 3 thread per inch
(a) 2.5 (b) 2.1667 (c) 3.5 (d) 2.75
552. Peening is
(a) clogging of particular file teeth (b) (c) (d)
575. If there are n no. of cells each having voltage of then total voltage is
(a) (b) (c) (d)
591. Drilling
(a) Harder material first (b) (c) (d)
594. MTCS
(a) Lift is to wing area (b) (c) (d)
595. Drawing is
(a) Auxiliary view (b) (c) (d)
601. MTCS
(a) Aluminum oxide porous & iron oxide unbroken (b)
(c) (d)
618. Al alloy is not heat treated properly to have uniform grain boundaries it has
(a) (b) (c) Intergranular corrosion (d)
620. Which is used to transfer rivet size from template to new sheet is
(a) (b) (c) (d) Transfer punch
621. Aside clearance between piston ring and cylinder wall is measured by
(a) (b) Thickness (DOUBT) (c) (d)
625. In magnetic particles inspection, Nickel plating does not given indication of
(a) (b) Discontinuities (c) (d)
626. In dye pnentrate inspection the defects under while light appears
(a) (b) (c) Red (d)
629. In ultrasonic test, when mechanical stress vibration is applied to crystal quartz then these are
(a) (b) (c) As in (a) and caries with the thickness of crystal (DOUBT)
630. Forms of corrosion which occurs between metal and non metal is
(a) (b) Crevice corrosion (c) (d)
634. For maximum elongation ductility tensile strength and impact resistance Mg alloy is
(a) Solution heat treatment (b) (c) (d)
637. An ac circuit consists of inductance of 10 capacitance 4 & resistance 8 the impedance of the circuit is
Z = R2 + (XL XC)2
(a) (b) 10 (c) (d)
642. The static vents with the flat surface plate at two position to
(a) (b) (c) Both (a) & (b) (DOUBT) (d)
644. An ac circuit has inductance 3 and resistance of 4, then impedance of the circuit is
(a) (b) (c) 5 (d)
648. Mg is ____________
(a) Susceptible to corrosion (b) Has tendency to crack (d) Both a & b
651. Rack is mesh with a gear, it is used to change (the purpose of rack and pinion is to change)
(a) Rotary motion to reciprocating motion (b) (c) (d)
658. Heated treated and non het treated metal 25, distinguished by
(a) (b) Eddy current test (c) (d)
676. The modulation in which, amplitude is kept constant and frequency is changed is called
(a) (b) (c) Frequency modulation (d)
678. In NDT of material by Dye penetrant inspection (DPI) the volume of defect is interpreted by
(a) (b) (c) Staining extent (d)
679. In UST, scanning is carried out by moving both probed simultaneously is opposite direction for
(a) Flash butt joint (weld) (b) (c) (d)
681. The fluid use for all types aircraft engine except rocket is
(a) (b) Air (c) (d)
684. In composites, repair, the part steeped rather than to be scrafed for
(a) Uniform shear stress (b) (c) Smoothness (d)
686. In uniform fluid flow, the fluid is made to flow through a tube and the pressure exerted by the fluid is
measured by
(a) Dynamic pressure (b) (c) (d)
688. The rust and corrosion is removed from highly stressed steel parts by
(a) (b) Fine buffing cloth on buffing wheel (c) (d)
689. Centre drill is used to produce
(a) Short hole and CSK hole (countersunk) (b) (c) (d)
695. The class of fit required for a right drive fit is or close drive.
(a) (b) (c) (d) Class 4
697. A device which gives lateral control and is mounted at the opposite surface of wing
(a) spoiler (b) (c) (d)
698. The pressure of water can be detected by (water inside honeycomb corecell)
(a) (b) (c) (d) Radiography
702. If two end terminals of PN junction is connected through a conducting wire than
(a) a steady current flows from P type to n type material
(b) no steady current flows from wire
(c) steady current flows from n type material to p type material through wire
(d) any one of the above
707. In a PNP transistor application, a solid state device is turned on when the
(a) base is negative w.r.t. the emitter (b) base is positive w.r.t. the emitter
(c) emitter is negative w.r.t. base (d) any of the above
709. To detect a minute crack using dye penetrant inspection usually requires
(a) That a developer is applied to flat surface (b) A longer than normal penetrating time
(c) The surface to be highly polished (d) Do not require excessive surface preparation
712. When capacitive reactance becomes equal to inductive reactance of a circuit it is called
(a) phase - in (b) phase out (c) resonant (d) impedance matching
714. When a lead acid battery is charged by constant current method, then its full charge can be detected as
(a) Three testing of electricity gives same specific gravity value (b) Voltage stops rising
(c) Gassing will occurs rapidly (d) All above are wrong
715. What should be the first step of the procedure in sketching an a/c wing skin repair
(a) draw heavy guideness (b) may out the repairs (c) block in the views (d) draw extension lines
716. A cathode (election emitter) used in thermionic emission must have following characteristics
(a) high matching point (b) high matching strength (c) low work function (d) all above are correct
717. When bolts and rivets are used to joint the metal sheets, then both should be protected from corrosion by
(a) applying grease on both (b) by plating bolt and rivets (c) by painting bolt and rivets
(d) they must be placed separately approximately, 2 times than the thickness of the metal being joined
722. If a line is divided into 25 division so that 25 divisions of this line is equal to 24 division of another line so
that minimum distance that can be measured is equal to difference between the value of each division, it is
the principle of
(a) DTI (b) Micrometer (c) Venire scale (d) Rules
726. For very accurate readings during such calibrations the thimble may be viewed under a microscope of
(a) low magnification (b) medium magnification (c) high magnification
727. When hydraulic fluid lines and electrical line is passing through same portion of a/c. then
(a) Hoses should be fitted above the wires and should be secured to a/c structure
(b) Electrical wire should be fitted above and to secure to a/c structure
(c) A minimum of 4 distance should be maintained between two and any of two can be unstable above
(d) Either of wire can be installed above and a minimum of
741. If the thimble scale zero mark is above the zero mark of barrel mark in micrometer, it indicates
(a) positive error (b) negative error (c) zero error (d) none
742. Mark the correct statement
(a) turbo jet engine require shorter runway length than turbofan engine
(b) turbo fan engines require lesser runway length for take off than turbo jet engine
(c) turbo jet engine produces more thrust than turbo fan (d) both b & c are correct
749. The ability to detect minute crack with radio graphy is called
(a) radio graph resolution (b) radio graph sensitivity (c) radio graph processing
(d) radiography density (e) all
750. In plastics, minute crack occurring at weaker area due, to applied load and extends both sides
(a) crazing (b) creeping (c) fatiguing (d) crevice corrosion
753. If 1 cm of main scale is divided in 20 equal division 24 division of main scale is divided in 25 equal
division of vernier scale, least count is
(a) 0.0002 cm (b) 0.002 cm (c) 0.2 cm (d) 2.0 cm
760. A micro switch will close or open a circuit with the movement of
(a) 1/16 or more (b) 1/16 or less (c) both a & b (d) none
773. Two batteries A is big & B is small are in same potential, the internal resistance of A
(a) A less (b) less than (c) un effected (d) equal
774. 7 x 19 indicates
(a) 7 strand & 19 wires (b) (c) (d)
786. End of steel bar some times painted some times various colors & color identify if differ at grade of steel
(a) Solid color identify the alloy & strips identify the (b)
(c) (d)
798. A generator having 8 pole runs at 6000 rpm find the freq.
(a) 400 C/S (b) (c) (d)
813. To prevent solder from rum of away from the surface to be joined
(a) Clef is commonly used to surround the area to be joined (b)
(c) (d)
821. Speed of motor increases, when load decreases current decreases because of
(a) frictional loss b/w motor moving parts (b) frictional loss b/w field winding and other parts
(c) included back emf increases (d) none
836. In a transformer is primary frequency changes from 50Hz to 60Hz, keep the pick voltage constant then
frequency
(a) increases in secondary by ratio 60/50 (b) decreases in secondary by ratio 50/60
(c) both 1 & 2 (d) none
838. When in a/c is required, embossing, etching and marking the electrical etching done by
(a) electrical etching pencil if applied lightly (b) electrical etching pencil but only for CRS
(c) electrical etching pencil is prohibited in a/c (d) both b & c
842. When coil of wire is placed horizontal to the earth surface, and a bar magnet dropped from the top
(a) fall with acceleration equal to g (b) fall with acceleration less than g
853. To improve tensile strength, ductility, shock resistance Mg. casting are normally
(a) SHT (b) PHT (c) Annealing (d) none
SUBJECTIVE QUESTIONS:
878. a) Orthographic projection N.D. BHATT page no. 470 diagram [fig 20.36]
b) How many flating are used in a/c plumbing explain them.
879. a) What is the purpose of circuit breakers & lines? What is the property of fuse?
b) What is the purpose of self locking nut? Describe any three types of self locking nut.
c) What are the chemical treatment applicable for Aluminum.
880. a) What are constant voltage & current charging method? Why they are used?
b) Write down truth table for NAND & NOR gates along with a neat sketch? Why they are called
universal gates?
c) What are the methods to control fuel contamination.
882. a) What do you mean by impendance. Calculate the impendance of the given circuit and current flow in
the given circuit.
b) What are the six special inspections to be carried out on airframe as well as engine.
c) Show with a neat diagram, flexible, extra flexible and non flexible cables.
883. a) Name the various parts of the micrometer & calculate its least count in inch.
b) What is the angle of attack and what are its effects on lift and drag.
c) Name the various instruments used for checking the performance of piston engine.
d) Describe the principle of NDT by ECI.
890. MTCS
(a) Ball peen Hammer is used where bent is sharp (b)
(c) (d)
893. MTCS
(a) Bolt has right hand threads except in special cases (b)
(c) (d)
904. 7 Resistor connected of 20 each in 11 voltage 2 ammeter connected across the Ckt. measure
(a) 7/10 Amp (b) 1/10 Amp (c) 2/10 A (d) 20/10 A
905. Speed of light energy is 3 lakes KM & freq. is 100 MHz, its wave length is
(a) 3 meters or 9.27 H (b) (c) (d)
907. To prevent corrosion Al. alloy sheets. How they are stored
(a) only the coat of Linced/oil is sufficient (b) use of plastic cover without oil coating
(c) Use of oil coating in addition to plastic cover
918. Brinelling is
(a) Indentation framed during a Brinell Hardness test (b)
(c) (d)
920. Algorithm
(a) has infinite (finite) inputs but definite output (b)
(c) (d)
927. In Dye penetrant process How the parts are cleaned before process
(a) Petrolium base process (b) Kerosene (c) Water & Volatile solvent
930. Millibars is the units of Borometric P/R then standard pressure is shown by
(a) 14.7 inches of mercury (b) (c) (d)
931. Theory of wt. & Balance, the distance between fulcrum & the object is
(a) Lever Arm (b) (c) (d)
932. Which Material the Magnetic lines of force can pass very easily
(a) Iron (b) (c) (d)
936. What information are necessary on blue print, while with threads on shaft
(a) Major dia, TPI, Type of thread (b)
(c) (d)
946. The Drawing in which objects are shown as TOP view, Front view, Bottom view
(a) Orthographic Drawing (b) (c) (d)
950. MTCS
(a) Al base material are created with & coating, it will form a thin oxide film on the surface of the metal is
exposed to air, it is prevent for there oxidation of the metal
(b) Al base metal are coated with anoding coating it will lead to the corrosion
(c) Cadmium plating of Al. will protect against corrosion
(d) None of the above
954. A substance in which chemical composition does not change but have different physical properties are
called
(a) Isotropic (b) Allotropic (c) Crystallization (d) Hygroscopic
956. Which of the following statement is true, regarding the inspection of a stressed skin metal wing assembly
known to have been critically loaded
(a) If the rivet shows no visible distortion further investigation is unnecessary
(b) If bearing failure occurred, the rivet shank will be fogged
(c) If genuine rivet tipping has occurred, groups of consecutive rivet heads will be tipped in the same
direction
(d) If shaft failure has occurred, the sheet will be distorted from the rivet hole, out to the edge of the joint
957. What is the recommended practice for cleaning a Fuel Tank before welding?
(a) Steam cleans the tank interior (b) Purge the tank with clean water
(c) Oxygen comes through pressure regulator & shut off value (d) All the above are correct
958. Aircraft parts which require more strength and little forming are made of Al - Alloy
(a) 6061 (b) 7075 (c) 2117 (d) 5052
959. The aircraft fluid hoses which offer minimum resistance to fluid flow & long service life are made of
(a) Teflon (b) Neoprene (c) Buna N (d) Butyl
977. Materials are to be case hardened very effectively up to 0.040 by which of the following method
(a) Induction Hardening (b) Liquid carburizing (c) Pack carburizing (d) Shot preening
978. Material heated up to lower temp. of higher critical temp. that is called
(a) Eutectoid (b) Ferrite (c) Austenite (d) Hypo eutectoid
980. After machining, welding, casting, or forming operation of steel part which heat treatment is carried out to
Remove internal stresses
(a) Normalizing (b) Annealing (c) Hardening (d) Tempering
988. Strain hardened Al alloy is usually used in construction of skin, cowlings, and fuel tanks
(a) Strain hardened Al alloy has better strength than heat treated Al alloy
(b) Corrosion resistant and easily bent, welded etc. (c) As in a & b
(d) Strain hardened Al alloy does not require heat treatment after structure is made
989. Which of the following is correct in case of tempering, higher the temp during tempering?
(a) Lower the strength & hardness but grater the ductility (b) Higher the hardness as well as ductility
(c) Increase strength, hardness & lower ductility (d) Decreases both ductility and strength
991. A dubblers is applied on structure having 3 rows of rivet & rivet dia is given D
(a) Minimum edge distance is 2D & rivet pitch minimum is 3D
(b) Edge distance is 2D and minimum spacing is 5D (c)
994. MTCS
(a) Plastic should be installed tightly so that it is not loose
(b) Plastic have greater coefficient of expansion that metal
(c) When installing plastics the plastic and metal should have similar expansion characteristics
997. MTCS
(a) a/c should be always jacked during leveling (b) may not be required to be jacked during leveling
(c) (d) All
1000. Borsical is
(a) silicon coated boron laminated (b) thermo set & polyester epoxy
(c) thermoplastic matrix (d) metal matrix
1003. Load is applied & removed and load direction is also reversed that is called
(a) fatigue set in (b) (c) (d)
1006. What is indicated by a black smoky residence streaming back from some of the rivets on an a/c?
(a) The rivets were excessively work hardened during installation
(b) Exfoliation corrosion is occurring inside the structure
(c) Fretting corrosion is occurring inside the structure
1010. Magnaglow is
(a) Similar to MPI
(b) dissimilar to MPI & the indication is taken under black light
(c) similar to MPI & the indication is taken under black light
1012. Thiokol is
(a) Polysulfide polymer (b) (c) (d)
1020. If it is determined that spongy brake action is not caused by air in the brake system what is the next most
Likely cause?
(a) Worn brake living (b) Internal leakage in the made cylinder (c) Deteriorated flexible looses
1021. Stress is
(a) Internal force that resists deformation (b) Dependant on strain
(c) Tension, Compression & torsion
1022. Hidden damage may extend beyond the area of visible deformation
(a) Rivet head will be tapped (b) Rivet head should be tapped with cape chisel
(c) Tap Blow the manufactured heads and the shop heads on the rivets and try to slip a piece of 0.020 feeler
Gauge under the heads
1023. MTCS
(a) The softer the material the more is the bend allowance
(b) The harden material the more is the bend allowance
(c) Both a & b (d) Bend allowance is similar irrespective of bend radius
1027. A substance in which chemical comport doesnt change out & have different physical properties-
(a) Isotropic (b) Hygroscopic (c) Allotropic (d) Crystallization
1028. When repairing a small hole on a metal stressed skin, the major consideration in the design of patch must
be :-
(a) Shear strength of riveted joint (b) use rivet spacing similar to a seam in skin
(c) the bond b/w patch skin be sufficient to prevent dissimilar possession
(d) both a & b
1036. How many cycles of a6 voltage are produced in a 6 pole alternation of revolving field type for each
revolution of rotor?
(a) 4 (b) 5 (c) 3 (d) 6
1038. Which treatment is given to copper alloy, to give a good bearing surface:-
(a) Anodising (b) Hardness (c) Pickling (d) Case hardening
1041. If aluminum strip is heated and suddenly quenched in cold water it is said to be -
(a) Normalized (b) Tempered (c) Solution heat treated (d) Precipitation heat treated
1051. Un - cona
(a) When a component is allowed in (b) service dill if insitu, without distant
(c) When inspection of components are displeased (d) When components can be easily replaced
1054. MTCS
(a) When swaging the terminal in the cable, the terminal is soldered to the cable to hold it in correct position
before savaging
(b) before swaging preservative compound is not applied on the cable (c) cut the length of cable
1055. MTCS
(a) while inspecting a part by x ray method defect is detester absorbing the x ray photon or photon
penetrate the part
1056. While inspection the part with magnetic particle in to show all the discontinuities/ electrets.
(a) Make longitudinal and circular magnetization (b) Only longitudinal magnetization is done
(c) Linear magnetization is done (d) all the above correct
1064. During Annealing after poat has been culled at 900f of full nonce the alternate method of this slow cooling
is
(a) cooling in water (b) cooling in air (c) by barging the points in Ash/lime (d) All
1068. In CRT display, coatings for collecting secondary electrons are connected to -
(a) Grid potential (b) 1st accelerating anode (c) 2nd accelerating anode (d) focusing anode
1069. Hard landing of an aircraft requires inspection off
(a) wing centre section (b) Balancing of flight centrals (c) (d) All the above are correct
1070. For modern jet aircraft, to ensure continuous airworthiness & inspection programmer for all structure to
(a) damage tolerant rating. (DTR) (b) Accidental damage rating (ADR)
(c) Environmental detection rating (EDR) (d) crack growth.
1071. Corrosion on metal is of direct corrosion & electron chemical corrosion. It terms as anodic direct chemical
attack is occurring simultaneously at the same point.
(a) Electrochemical corrosion taking place at measurable distance apart, the change in direct chemical attack
is occurring simultaneously at the same point.
(b) Electrochemical attack is occurring simultaneously at the same point where as the direct chemical attack
occurring at a measurable distance apart.
(c) Both are occurring at the same point (d) Both are occurring at a measurable point.
1072. If the surface of anodic treated Al. allow is corroded, the corroded the corrosion is removed by corrosion
(a) severe abrasive material (b) Al. wool (c) steel wool (d) wire brush
1073. Why are the iron cores of most of the induction coils laminated:-
(a) To reduce the core reluctance (b) To increase the core permeability
(c) To reduce the effects of eddy current
(d) To reduce the production of weak areas & strong areas on the core faces
1074. The voltage in an A.C. Transformer secondary that contains twice as many loops as the primary will be:-
(a) Greater & the amperage less than in primary (b) Greater & the amperage more than in primary
(c) Less & the amperage less than in primary (d) Less & the amperage greater than in primary
1075. Which is the method used for restoring generator field resident magnetism:-
(a) flash the field (b) demagnetize the commutator (c) reset the brushes (d) energize the armature
1077. MTCS
(a) corrosion develops in thicker metal faster than the thinner metal
(b) corrosion develops in thicker metal faster than the thinner metal
(c) corrosion develops in both the metal in same way
(d) heat treatment can change the corrosive property of the material
1079. MTCS
(a) lead acid batteries exposed to cold temp. are subjected to plate damage due to freezing of the electrolyte
(b) to prevent the freeze damage, maintain the sp. Gravity at reasonable high level bearing in mind that lead
acid battery are subjected to a constant discharge due to the internal chemical action
(c) Ni Cd battery, the electrolyte will freeze at approx. 150 F to 750 F (d) All
1082. MTCS
(a) intergranular corrosion may exist without visible surface evidence
1083. When repairing a small hole on a metal stressed skin, the mazor consideration on the design of the patch
should be
(a) shear strength of a riveted joint
1088. Mark the correct statement, when securing Al and Mg alloy structure
(a) Al washer should be used under steel bolt head (b) Al washer used under nut of steel
(c) Any corrosion attacks washer rather than structure (d) All of the above
1092. Clogging of metal particle in the gullet of file teeth is known as:
(a) peening (b) pinning (c) clogging (d) stretching
1096. Load is applied per square inch a material can with stand without resulting in a permanent elongation more
Than 0.0001 per inch of gage length after complete release of stress is known as:-
(a) Elastic limit (b) proof stress (c) Proportional limit (d) Yield strength
1129. Which of the followings having ve coefficient of resistance with increase in temp.
(a) Conductor (b) Thermistor (c) Transistor (d) Relay
1130. The property of fluid of giving off vapour in sufficient quantity so as to ignite momentarily when flame is
applied is known as.
(a) Fine point (b) Flash point (c) Vapour point (d) Burning point
1135. Before jacking an a/c few steps are taken regarding this mark the correct statement:-
(a) for heavy a/c and smaller a/c same procedure & precaution should be observed
(b) jack must be of capacity 20% more than the weight to be lifted
(c) for proper capacity, condition of locking pin or arm, proper functioning (d) all of the above
1158. If aluminum part is not quenched within recommended time after heating then:-
(a) corrosion may occur (b) aluminum will be excessive brittle
(c) repreceipitation will occur (d) Both a & c
1160. During refueling chock is set at little distance from wheel because:-
(a) to absorb shock when tire is set (b) electro static generated
(c) chock may be trapped into the fire (d) chock can be applied if a/c moves during refueling
1166. To increase range of Ohm meter to measure high voltage required internal N resistance to be:-
(a) Low (b) High (c) Constant (d) Balance with defection of probes
1167. Advantages of A.C. over D.C. for use on long r range transmission is:-
(a) State and easy to generate (b) It is easy to rectify A.C.
(c) Thinners conductors are used (d) All above are correct
1168. In capacitor charging, if key is open and if distance R betn plates is increased, then
(a) Capacitance decreases (b) Capacitance increases
(c) P.D. increases (d) P. D. decreases and stored
1171. MCS:-
(a) Zener diod used for as amplifier (b) Tunnel diode used for voltage regulator
(c) As in b and as an oscillator
(d) Varactor diode is used for skitching circuit of electronic tunner
1175. MTCS:-
(a) Zener diode used for as amplifier (b) Funnel diode used top voltage regulator
(c) As in (b) and as an oscillator
(d) Varactor diode is used for sketching circuits of electronic tunner
1182. MCS:-
(a) Cold Water quenching minimize distortion & cracks
(b) Hot water quenching minimizes distortion & alienates cracks
(c) Spray quenching reduces the wear and corrosion
(d) Quenching process not has considerable effects.
1183. Heat treatment of Al alloys and after it allowed to cool for 4 to 5 days is:-
(a) Natural ageing (b) Artificial ageing (c) Both a & b (d) Room temp of alloys
1186. Most important factor which affects the indication of dye penetrate inspection check is:-
(a) Not proper application of Dye (b) Not proper application of penetrate
(c) Parts are not thoroughly degaussed & cleaned (d) All of the above
1209. MCS
(a) Roller bearings takes thrust (b) Radial bearings are used for shaft gears etc.
(c) Ball bearings withstand heavy radial loads (d) All above correct
1210. While demagnetize the parts:-
(a) By passing sufficient A.C. into the field (b) By passing a.c. slowing out to the magnetic field
(c) By repeatedly apply a.c. over the part (d) Increasing the strength of magnet then cutout a.c.
1216. MCS:-
(a) Corrosion on Al, have etching and pitting (b) Corrosion on Cu, have greenish film
(c) Corrosion on Mg, have etching and pitting (d) All are correct
1222. MCS:-
(a) QNF, atmospheric pressure reads zero
(b) QNH, bar metric pressure above elevation at meansealve
(c) QNE, barometric pressure at altitude (d) Both b & c are correct
SET 30
1228. Which is unpaired?
(a) dye penetrant capillary acceptance (b) ultrasonic test peizo electricity
(c) eddy current test current acceptance (d) magnetic test skin test
1230. The static vents with the flat surface plate at two position to
(a) minimize position error (b) have is formation freedom
(c) both a & b (d) None
1256. End of steel bar sometimes painted in various colors and color combination as a mean of identifying
different grade of steel
(a) Solid colors identify the alloy and strips identify the carbon contents
(b) strips identify the alloy and solid colors identify the carbon content
(c) both a & b (d) none of the above
1261. In PFD, when used fluorescent, material color of defective part and sound part is
(a) brilliant yellow green and blue violet (b) brilliant yellow green and bright red
(c) bright red and blue violet (d) none of the above
1264. If no marking of drill, identification of drill can be measured by drill gauge having
(a) fraction on right and no. on left (b) fraction on left and no on right
(c) both a & b (d) none of the above
1265. Dia of rivet is (15A)
(a) 2 times of thickness of sheets (b) 3 times of thickness of thickest sheet
(c) 3 times of thickness of joint sheets (d) equal to grip length
1269. What size of the hole should be bored before cutting a 2.5 internal acme thread having 3 thread per inch
(a) 2.5 (b) 2.1667 (c) 3.5 (d) 2.75
1275. The modulation in which, amplitude is kept constant and frequency is changed is called
(a) amplitude modulation (b) space modulation
(c) frequency modulation (d) phase modulation
1277. In uniform fluid flow, the fluid is first made to flow through a tube and the pressure exerted by the fluid is
measured by
(a) dynamic pressure (b) static pressure (c) reynolds no. (d) all
1279. The rust and corrosion is removed from highly stressed steel parts by
(a) abrasive paper (b) fine buffling cloth on buffling wheel
(c) wire brush (d) all
1287. The dimensional inspection of a bearing in rocket arm can be accomplished by:
(a) depth gage and micrometer (b) telescoping gage and micrometer
(c) thickness gage and push fit arbor
1305. MTCS:
(a) Al alloy bolts of dia less than mm are not used in primary structure
(b) All Al alloy nuts and bolts are used where frequent removal is required
(c) Both a & b are correct (d) None of the above
1306. MTCS
(a) lap joint is best for oxy acetylene welding (b) single lap joint is resistance to shearing
(c) single lap joint is resistance to bending (d) all of the above are wrong