Professional Documents
Culture Documents
Project Control Survey - PPSX
Project Control Survey - PPSX
PROJECT CONTROL
SURVEY
Lecture 4
1
Project Control Surveys
Section 29. Project Control Surveys shall be conducted in order
to establish set of reference points for a Cadastral Survey, Public
Land Subdivision Survey, Townsite Reservation, and other
similar survey projects which cover a whole or a portion of
municipality or city, with accuracies belonging to:
CAD-668
Magallanes
CAD-169
Nasipit
CAD-84
Butuan City
PLS-4
Buenavista
CAD-84, Butuan City Cadastre
NAMRIA
Survey Order
DENR-NAMRIA
Project Area
Recommendation: RED
Issued by: NAMRIA Administrator
Submittal of
Execution of Geodetic Geodetic Control Survey
Control Survey Returns
LMS-DENR
Project Area
PROJECT CONTROL
SURVEY Verified by: LMS
Approved by: RTD for Lands
Submittal of
Execution of Project Project Control Survey
Control Survey Returns
Geodetic Engineer/Survey Party 14
PROJECT CONTROL
SURVEY PROCEDURE
Instruments To Be Used
The survey instruments to be used are the following:
a. Electronic Total Station (ETS), GNSS Receivers, or combined
GNSS/ETS.
b. If ETS surveying instruments are to be used, the control
survey shall be conducted either by traverse, triangulation
or any combination thereof, referred from an established
PRS 92 reference monument.
Project Control Survey
Section 30. If the Project Control is an independent project,
provisions of Section 3 of this Manual shall apply subject to the
following conditions:
Section 31. The survey party shall be the Survey Control Team of
the survey projects.
The first primary control point known as P1 of the main control shall be
designated as BLLM No. 1 of the project, the second primary control
point(P2) or the last main control station shall be designated as the BLLM
No. 2 of the project.
Network Design and Map Preparation
e. The main control shall start from PRS 92 Primary Control Point and closes
to another PRS 92 Control Point of the project and their proposed location
shall be plotted as accurately as possible on the Network Scheme
considering that they shall control all subsidiary reference points within the
project.
f. When no location monuments have been previously established, a pair of
Bureau of Lands Location Monuments (BLLMs), to be numbered 1 and 2
shall be approximately plotted on the map at the most suitable location
and as near as possible to the center of the municipality or the project.
Network Design and Map Preparation
g. The points to be established shall be approximately plotted on the map.
The approximate line routes or the connection lines from one control point
to another shall be shown on the map.
h. All the fixed controls (old Control Points) based on the available records
shall be accurately plotted. At least three (3) Second Order or Third Order
Geodetic Control stations shall be included in the Network.
i. Whenever the main control includes established geodetic control
stations, the main control shall be designed such that it can be divided into
loops wherein each loops shall start from one geodetic control station and
shall close to another geodetic control station;
Network Design and Map Preparation
j. The main controls to be established, as much as possible, shall follow the
project boundary. If the place is rugged as shown in the topographic map,
the controls shall be placed near the boundary where it is fairly level,
although they are a little beyond the administrative jurisdiction of the
concerned LGU.
k. In case mountain peaks or hills define the boundary of municipality or
project, the primary controls shall be located at the base of the mountains
or hills. If the terrain is rugged, it may be plotted along the existing road
lines located as near as possible to the boundary;
Network Design and Map Preparation
l. Additional pairs of location monuments shall be established along the
main control of the project at an interval of around 5 kilometers or at least
a pair for every Barangay, whichever provides the shorter distance, and
shall be designated and numbered as BLLM No. 3 and BLLM No. 4; BLLM
No. 5 and BLLM No. 6; etc.. Pursuant to Section 28, DAO No. 2007-29,
consideration should be taken by the Geodetic Engineer to ensure that no
lots shall have a distance of more than one (1) kilometer from the nearest
reference point, whenever possible, based on the project control network
design.
Reconnaissance
Section 38. Provisions of Section 14 of this Manual shall apply in
addition to the following conditions:
a. Intervisibility between pairs of stations.
b. Line of sight is not in any way obstructed by transportation vehicle.
c. Condition of the atmosphere.
Project Control Monuments
Section 39. The position of reference points shall be defined and marked on
the ground by monuments of permanent nature in accordance with the
standards set forth in Section 15 of this Manual for the 3rd Order Accuracy.
km
Conduct of Project Control Surveys
Section 45. Ground survey for the establishment of Project Control using
GNSS instrument shall be conducted following the provisions of Sections
23-27 of this Manual.
GNSS Receiver - line of sight not required between measured points but
requires long period of observations
In the absence of 2nd and 3rd Order geodetic control stations within the
distance of 10km from the project boundary, connection of primary
precision shall be made to any other point of reference certified by LMB.
Grid Azimuth
Section 49. The grid azimuth to be used in the Cadastral Project shall
be derived from the PRS92 grid coordinates.
Connection with Adjoining Projects
Section 50. The Main Control of the project shall be connected to the
adjoining cadastral projects for conformity. However, the following shall
govern this process:
a. The adjoining project/s must be in the PRS92 and was duly approved by
the DENR-LMS Office concerned.
b. GNSS observations shall be conducted on the two extreme stations
common to the two projects to determine the azimuth and distance of the
line connecting the said points.
c. If there is a discrepancy between the adjoining projects and the on-going
project, a report shall be made and shall be forwarded to the LMS, which in
turn shall form a Technical Committee to investigate the matter and submit
a corresponding recommendation to the RED.
PLS-736
Cabadbaran City
CAD-668
Magallanes
Extreme Station
BLLM#11
BLLM#12
CAD-169
Nasipit
CAD-84
Butuan City
PLS-4
Buenavista
Section 52. The RED and/or the RTD for Lands and/or their duly authorized
representative/s upon coordination with the CENRO concerned shall have
the full and unrestricted rights to inspect and supervise the operations of
the survey team and to issue instructions from time to time, as they may
deem necessary for the proper execution of the project.
PROJECT CONTROL
SURVEY RETURNS
Project Control Survey Returns
Section 166. The following shall form part of the survey returns of the
Project Control Survey:
d) The 3rd and 4th Order project control stations established shall be
plotted in appropriate scale.
a. Preliminary Evaluation
b. Technical Evaluation
Verification
PRELIMINARY EVALUATION or initial examination shall be conducted to
determine if the survey returns are complete as per List of Transmittal:
1. Certifications, Reports, endorsement letters, etc.
Replacement of key personnel and equipment shall be with prior
authority from the RED upon endorsement of the RTD for Lands.
2. References and Technical Documents.
3. If the ETS is used, it shall be calibrated/field tested by the LMB/LMS
before and after its use in the project. If the instruments used are GPS
Receivers, GPS Observation raw data on digital form and RINEX files (if
non- Trimble receiver was used) shall be submitted.
Verification
PRELIMINARY EVALUATION or initial examination shall be conducted to
determine if the survey returns are complete as per List of Transmittal:
4. Field notes and computations.
5. If the method of Triangulation was used in some part of the project, the
field notes and computations shall be submitted.
Verification
TECHNICAL EVALUATION shall be conducted in order to determine
accuracy, analyze error in observation, and detect mistakes.
1. GPS observations
2. Project Control Map (PCM) is of standard size (54 x 54 cm. with 4 cm.
borderlines), signed by the Chief of Party, prepared in a convenient scale
stations :
1. At the station where position was taken (only stellar observation
should be observed).
2. At every BLLMs pair. However, for BLLM Nos. 1 and 2, only stellar
observation should be conducted.
3. At the junctions of subsidiary loops.
4. At the junctions of test traverse.
5. Along the primary traverse at every 20-25 stations.
6. Along the secondary traverse at every 25-35 stations.
Verification
7. Control connection requirements Check the connection made at the
following:
a. Stations of previously approved adjoining projects
b. Triangulation stations within the boundary of the projects.
Verification of Monument Description Book
8. Monument Description Book Requirements :
a. Check that the geographic and grid coordinates of BLLM No. 1 are
Indicated.
b. Check that there are at least three (3) references for each station.
Each reference points should be described with corresponding
distance and bearings from station and BLLMs.
c. Check that each station and BLLM is sketched in its location.
Verification of Field Notes Book
9. The Technical Verification Procedures shall be as follows:
a. Examine the Field Notes Book :
1. Angle Book - check the mean interior and exterior angles.
2. Distance Book check the mean horizontal distance.
3. Astronomic Book check the input in astronomic computation.
Verification of Astronomical Observation Computation
as computed.
2) Check the grid coordinates of all BLLMs and primary stations.
3) Check the grid azimuths and distances of primary lines and pairs of
BLLMs.
4) Check references, there should be at least three references for each
primary control station and BLLM. Each reference should be described
If found in order, the Chief of Regional Surveys Division shall sign the
Project Control Map and other necessary documents and prepare
endorsement letter to the concerned RTD for Lands for approval in
accordance with Section 62, DAO 2007-29.
Approval
Section 62 of DAO 2007-29. The survey returns of the main and subsidiary
control shall be submitted to the LMS for verification and approval.
Only project controls that were verified and approved shall be used in the
verification of Political Boundary and Cadastral Lot Surveys.
THANK YOU!