Professional Documents
Culture Documents
Endogenic Process PDF
Endogenic Process PDF
ENDOGENIC
PROCESS
ENDOGENIC PROCESS
•Processes that is formed
or occurring beneath
the surface of the Earth.
MAGMA
a mixture of molten
rock, minerals and
gases.
This mixture is usually made up of a hot
liquid base called the melt, minerals
crystallized by the melt, solid rocks
incorporated into the melt from the
surrounding confines and dissolved
gases.
MAGMA
originates in the lower part of
the Earth’s crust and in the
upper portion of the mantle
known as asthenosphere.
How Are Magmas Formed ?
• At about 30 to 65 km below the earth’s surface, the
temperature is high enough to melt rocks into magma. The
reason why it is difficult to drill holes deep into the crust is
that the temperature rises about 30 degree for every
kilometer.
• The asthenosphere which is between 100 to 350km deep is
so hot that most of the rock is melted . The melt flows very
slowly because it is under intense pressure. Magma reaches
temperatures between 600 degree 140 degree Celsius.
Gases in Magma
• Deep in the Earth, nearly all magmas contain gas dissolved
in the liquid, As magma rises at the surface of the Earth,
pressure is decreased and the gas forms a separate vapor
phase. This is somewhat similar to carbonated beverages
which are bottled at high pressure.
• When magma emerges on the surface of the Earth, it is
called lava. Lava spilling over or erupting from craters is
usually bubbly, a sign that gases are escaping.
Viscosity of Magmas
•Viscosity is the resistance to flow
(an antonym for fluidity).
• Magma with higher silica content has higher viscosity. Viscosity
increases with increasing silica concentration in the magma.
• Magma with low temperature has higher viscosity than those
with high temperature. Viscosity decreases with increasing
temperature of the magma.
Magma Escape Routes
• Magma leaves the confines of the asthenosphere and
crust in two major ways; an intrusion or extrusion.
• Magma can intruded into low-density area of another
geologic form such as a sedimentary rock. When it cools
and hardens, this intrusion develops into an pluton
commonly know as an igneous intrusive rock.
• Magma rises towards the Earth`s surface where are less
dense surrounding rocks and when a structural zone allows
movement.
Magma Chamber
• Magma develops within the upper mantle and crust where the crust
where the temperature and pressure conditions favor the molten state.
Magma collects in areas called magma chamber.
• There pool of magma in a magma chamber is layered. The least dense
magma rises to the top. The densest magma sinks at the bottom of the
chamber.
• During an eruption, gases, ash and light-colored rocks are emitted from
the least dense top layer magma chamber. Dark, dense volcanic rock
from the lower part of chamber may be released later.
Ways to Generate Magma
1. Decompression Melting
2. Transfer of Heat
3. Flux Melting
Ways to Generate Magma
1) Decompression Melting
involves the upward movement of the
Earth’s mostly solid mantle
this hot material rises to an area of lower
pressure through the process of
convection.
Ways to Generate Magma
2) Transfer of Heat
Happens when hot, liquid rock intrudes
into the Earth’s crust. As the liquid rock
solidifies, it loses this heat and transfers it
to the surrounding crust. This is similar to a
hot fudge poured over cold ice cream.
Ways to Generate Magma
3) Flux Melting
It occurs when water or carbon
dioxide added on rocks these affects
the melting point of rock when added
with water beneath the earth it
generates magma.
Types of Magma
1. Felsic Magma
2. Intermediate Magma
3. Mafic Magma
4. Ultramafic Magma
Felsic Magma
This type of magma has viscosity
level there has low in iron but high
in potassium and sodium this form
makes granite rocks.
Intermediate Magma
This normally found in
volcano that erupts, after
the eruption it releases a
lava that has high silica
and very viscous/ it
commonly produced
Andesite Rock.
Mafic Magma
Mafic magma has relatively low silica
content but high in iron and
magnesium. This magma has a low
gas content and low viscosity. Mafic
magma has high average
temperature which contributes to its
low velocity. Low velocity means that
mafic magma is the most fluid of all
magma types.
Mafic Magma
basalt
Ultramafic Magma
Today our planet is to cool, for
ultramafic magma to form. This
is a probably a good thing,
since ultramafic magma would
be the hottest and fastest
flowing magma.
Rock Deformation
1.Stress 3.Joints
2.Strain 4.Faults
Rock Deformation
1) Stress
the force that could create deformation
on rocks in their shape and/ volume.
Great forces from several directions may act on the
lithospheric plates causing them to move. Although this
crustal plates are elastic solid, they are subjected to great
forces such as pulling, pushing or squeezing.
Kinds of Stress
1) Lithostatic stress
Rock beneath the Earth’s surface
experiences equal pressure exerted
on it from all directions because the
weight of the overlying rock.
It is like the hydrostatic stress (water pressure) that a person
feels pressing all over his body when diving down deep in the
water.
Kinds of Stress
2) Differential stress
stress on rocks that are caused by an
additional due to unequal stress due to
tectonic forces.
3 Kinds are
a) Tensional stress (stretching)
b) Compressional stress (squeezing)
c) Shear stress
Types of Differential Stress
a) Tensional stress (stretching). This is when rock is stretched apart
or pulled apart. Where crustal plates diverge, rocks are pulled
apart.
b) Compressional stress (squeezing). This is when rock is pressed,
squeezed or pushed together . It’s like a car caught in the
middle of a long pile up on the highway. Where crustal plates
collide, rocks are compressed or pushed.
c) Shear stress which results in slippage and translation. With
shear stress, the rock is being pulled in opposite directions. It is
similar to the motion between individual playing cards when
the top of the stack is moved relative to the bottom.
Rock Deformation
2) Strain
ability of a rock material to
handle stress depends on the
elasticity of the rock.
Types of Deformation
a) Elastic deformation
For small differential stresses, less than the yield strength,
rock deforms like a spring. It changes in shape by a very
small amount in response to the stress. The deformation is
not permanent. This deformation is reversable. The rock can
return to its original shape.
b) Brittle deformation or Fracture
Near the Earth’s surface rock behave in its familiar brittle
fashion. If a differential stress is applied that is greater than
the rock’s yield strength, the rock fractures. Fracture is an is
an irreversable strain wherein the rock breaks.
Rock Deformation
3) Joints
fractures in rocks that show
little or no movement at all.
Rock Deformation
4) Faults
are extremely long and deep
break or large crack in a rock
a result of continuous pulling
and pushing.
Types of Faults
b) Strike-slip fault
Disclaimer:
The pictures used in this slideshow presentation were obtained from various internet websites and will be only used
for educational purposes only.