Professional Documents
Culture Documents
PA microphone panel
PA microphone & Alarm panel
Alarm panel
SPA-M6D SPA-A6CD
ZONE 1
Talk-Back
1 GENERAL
ZONE 2
GENERAL
ALARM
2 ABANDON
ZONE 3
ABANDON
ALARM
3 MANUAL
ZONE 4
MANUAL
4 RESET ALARM
ZONE 5
5 SPARE
ZONE 6
6 DIM. EMS
EMERGENCY
PA
ALL TALK
LS zone 1
Cabins
ACM Telephone System
LS zone 2
SPA-V2 Main Unit Accommodations
PABX
LS zone 4 Engine
area
LS zone 5
Open deck
Entertainment
LS zone 6
Open deck
Figures
Figure 1 Available cabinet height options.................................................................................................................. 7
Figure 2 Cabinet measurements front, side & rear.................................................................................................... 8
Figure 3 Fastening for 20U and higher racks............................................................................................................ 8
Figure 4 230 VAC and 24 VDC connections............................................................................................................ 13
Figure 5 230/230 VAC with SPA-FAIL board............................................................................................................ 14
Figure 6 Jumper for Entertainment Output to external system................................................................................ 32
Figure 7 Jumper for audio from Talk-Back system................................................................................................... 32
Figure 8 Jumpers for Alarm Priorities....................................................................................................................... 33
Figure 9 Jumpers for external audio out per zone................................................................................................... 33
Figure 10 Jumpers for fire crew alarm per zone........................................................................................................ 33
Figure 11 Jumpers for PBX audio output per zone.................................................................................................... 33
Figure 12 Jumpers for Talk-Back with emergency message..................................................................................... 33
Figure 13 Jumpers for override on All Call vs. zones 1-6.......................................................................................... 34
Figure 14 Jumpers for override on normal & EMS vs. EMS only.............................................................................. 34
Figure 15 Jumpers for override with internal or external 24 VDC.............................................................................. 34
Figure 16 Alarm/Mic Panel with Local Mute for Dual System.................................................................................... 50
The system also meets additional requirements from the following class
societies:
DNV, GL, BV, LR, RS, CCS, RINA, and ABS.
The SPA-V2 system and its components have been tested according to
the following regulations:
L Note that this manual describes the standard SPA-V2 system and equipment. For
systems with additional equipment and configuration, see project documentation
and relevant manuals.
b) Public Address
- Interior spaces, including sleeping positions and cabin bathrooms:
75 dB (A) and at least 20 dB (A) above ambient noise level.
Examples of high fire risk areas are, apart from machinery space of
category A, galleys and pantries containing cooking appliances, laundry
with drying equipment, spaces defined by paragraphs (8), (12) and
(14) of SOLAS Ch.II-2 Reg. 9.2.2.3.2.2, and areas with fuel handling
equipment.
Do not run the installation cable from microphone and alarm panels
parallel or near to the installation cable for loudspeakers or power
cables.
The shields must be interconnected in junction boxes and grounded in
the SPA main unit only.
2.6.1 Cabinets
The cabinets are standard 19” racks with heights from 12U to 40U
module units depending on the number of amplifiers, entertainment
sources, monitors, and other modules in the actual installation.
40U
30U
SERIES MASTER CONTROL
MAIN SWITCH
3 3 4 6
2 4 2 4
5 5 2 8 POWER
1 1
0 10
MAIN SWITCH
3 4 3 4 4 6
2 2
5 5 2 8 POWER
1 1
0 10
24U
SERIES POWER AMPLIFIER
SERIES POWER AMPLIFIER
dB -40 . -12 . -6 . 0 +1
dB -40 . -12 . -6 . 0 +1
OUTPUT LEVEL OVERL. ON
20U
0 0 5
0 0 5
I
I
0
0 -10 +10 -10 +10 0 10
MAIN SWITCH
3 4 3 4 4 6
2 2
5 5 2 8 POWER
1 1
0 10
dB -40 . -12 . -6 . 0 +1
OUTPUT LEVEL OVERL. ON
16U
0 0 5
0 0 5
I
I
0
0 -10 +10 -10 +10 0 10
12U
0 0 5
0 0 5
I 0 0 5 0 0 5
I
I I
0
-10 +10 -10 +10 0 10
0
0 0 -10 +10 -10 +10 0 10
BASS TREBLE MASTER VOLUME POWER
-10 +10 -10 +10 0 10 -10 +10 -10 +10 0 10
BASS TREBLE MASTER VOLUME POWER
BASS TREBLE MASTER VOLUME POWER BASS TREBLE MASTER VOLUME POWER
OUTPUT LEVEL OVERL. ON OUTPUT LEVEL OVERL. ON OUTPUT LEVEL OVERL. ON OUTPUT LEVEL OVERL. ON
0 0 5
0 0 5
0 0
I
0 0 5 5 0 0 5 0 0 5
I
I I I I
0
-10 +10 -10 +10 0 10 0
0 0 0 0 -10 +10 -10 +10 0 10
BASS TREBLE MASTER VOLUME POWER
-10 +10 -10 +10 0 10 -10 +10 -10 +10 0 10 -10 +10 -10 +10 0 10 -10 +10 -10 +10 0 10
BASS TREBLE MASTER VOLUME POWER
BASS TREBLE MASTER VOLUME POWER BASS TREBLE MASTER VOLUME POWER BASS TREBLE MASTER VOLUME POWER BASS TREBLE MASTER VOLUME POWER
2.6.3 SPA-M6BOKS
For SPA-M1 and SPA-M6 when wall mounted.
96
66
40
96 17.5
4 6
75
86
96
5
0
2.6.10 SPA-BOXM1
For VM15-R and VM50-R when wall mounted.
Ø4
33.5
4
4
0
0 5
5
EMERGENCY
POWER POWER
SUPPLY SUPPLY
24VDC 24VDC
+ - + -
X1 1 2 3 1 2 3 X2
AMPLIFIER AMPLIFIER
24VDC 230VAC 24VDC 230VAC 24VDC
INTERNAL L N - + L N - +
POWER SUPPLY E E
230VAC
L 1
SHIP’S MAIN 230VAC N 2
POWER SUPPLY E 3
XA
SHIP’S EMERGENCY + 1
24VDC POWER SUPPLY _ 2
XB
SHIP'S EMERGENCY
230VAC POWER SUPPLY
VOLUME CONTROLS
100V LINE OUT
ZONE 1 F> 1 1 3 5 +
24V OVERRIDE>
ZONE 1 0> 2 6 -
ZONE 2 F> 3 1 1 F<100V IN F 3 LOUDSPEAKER
100V OUT> ZONE 1
ZONE 2 0> 4 2 0 0 4
ZONE 3 F> 5
ZONE 3 0> 6
ZONE 4 F> 7
ZONE 4 0> 8 VOLUME CONTROLS
ZONE 5 F> 9
ZONE 5 0> 10
ZONE 6 F> 11 2 4 5 + LOUDSPEAKER
24V OVERRIDE> ZONE 6
ZONE 6 0> 12 6 -
X14 2 1 F<100V IN F 3
2 0 100V OUT>0 4
-24V 2
+24V 3 4
-24V 4
X61
1
<100V LINE IN
2
<100V LINE IN
3
>100V LINE OUT
4
>100V LINE OUT
5
<+24V OVERRIDE
6
SPA-ENT4-V2 <-24V OVERRIDE
MAIN RACK
SPA-EMS
J2=OFF
J1=EMS Only
IX6 IX5
[RJ45] [RJ45]
RJ45
RJ45
Cat-5e Cat-5e
RJ45
RJ45
A30
SPA-TERM-V2
5x2x0,75mm² 5x2x0,75mm² 6 5 4 3 2 1
1 F IX11 IX10 IX9 IX8 IX7 IX6 IX5 IX4 IX3 IX2 IX1
2 F [RJ45] [RJ45] [RJ45] [RJ45] [RJ45] [RJ45] [RJ45] [RJ45] [RJ45] [RJ45] [RJ45]
3 O
MASTER STATION 3130 P1 PA INTERFACE 99309-005 P2
LINE 1 1 1 1 1 1 1 F
AUDIO IN AUDIO TO AMP
LINE 2 2 2 2 2 2 2 F
3 O - 2
LINE 3 3 3 3 ZONE 1 COMM 2 3 1 1
4 + 1
LINE 4 4 4 4 ZONE 2 COMM 1 4 3 5 2 2
3 3
LINE 5 5 5 5 ZONE 3 5
AUDIO TO AMP 1 4 4
NO NC N
LINE COMM 6 6 6 ZONE 4 6 5 5 1
2
EXT. SIGN. 1 7 7 7 ACT. COMM 2 7 3 6 6 2
7 7 3
EXT. SIGN. 2 8 8 8 +24Vdc COMM 1 8
1 F 8 8 4
EXT. SIGN. 3 9 9 9 0Vdc 9 9 9 5
AUDIO TO AMP 2 F
EXT. SIGN. 4 10 10 SCREEN 10 3 O 10 10 6 1
11 11 7 2
EXT. SIGN. COMM 11 8 COMM 2 11
12 12 8 3
12 COMM 1 12
EXT. LOUDSP. 4
13 9 13 5
AUDIO TO AMP
14 1 14 6
MIC. STBD 7
15 2 COMM 2 15
8
16 1 COMM 1 16 9
TALK STBD 10
17 2 17 1 1 1 1
OUTPUT ZONE 1 11
18 18 5 2 2 2 2
MIC. PORT 12
1 1 3 3 3 1 3
19 19
OUTPUT ZONE 2 2 2 4 4 4 2 4
20 20 6 1 F
3 3 5 5 5 3 5
TALK PORT 2 O
21 24Vdc-PS 21 4 4 6 6 6 4 6
OUTPUT ZONE 3 5 5 7 7 7 5 7
22 22 7
6 6 8 8 8 6 8 1 +
+24VDC 23 1 23 7 7 9 9 9 7 9 2 -
OUTPUT ZONE 4
0V 24 2 24 8 8 8 10 10 10 8 10 3
9 11 11 11 9 11
SCREEN 25 SCREEN 25
10 12 12 12 10 12 1 +
LINE 6 26 11 13 13 13 11 13 2 -
LINE 7 27 12 14 14 14 12 14 3
LINE 8 28
LINE 9 29
LINE 10 30
LINE 11 31
LINE 12 32
LINE 13 33
LINE 14 34
LINE 15 35
1
2
3
4
J3
5
6
7
8
EXT 5 41
EXT 6 42
EXT 7 43
EXT 8 44
DATA 45
DATA-REF 46
AUDIO A 47 1
AUDIO B 48 2
+ RS 232 TX 49
- RS 232 RX 50
REF. 51
DIG IN 1 52
DIG IN 2 53
DIG OUT 1, ZONE 1 54 3
DIG OUT 2, ZONE 2 55 4
DIG OUT 3, ZONE 3 56 5
DIG OUT 5 57 7
DIG OUT 4, ZONE 4 58 6
CALL SIGNAL OUT 59
60 Note!
GP AUDIO IN
61 Use cable 0,75mm twisted pair
with outer braided copper screen.
GP AUDIO OUT
62 The screens must be interconnected
63 in junction boxes and grounded
64 in a common point in the central unit only.
GP AUDIO IN
65
JBs are yard supply.
66
GP AUDIO OUT
67
1 <AUDIO PABX
2 <AUDIO PABX
PABX EXCHANGE
3 <SWITCH PABX
4 <0V SWITCH PABX
ENTERTAINMENT SOURCE 5 <AUDIO ENTERTAINMENT
6 <AUDIO ENTERTAINMENT
NOT IN USE 7 <AUX 1
8 <AUX 1
9 <AUX 2
NOT IN USE
10 <AUX 2
11 <AUX 3
NOT IN USE
12 <AUX 3
Note: X11
Entertainment requires SPA-ENT4-V2
or SPA-MUL-V2 to function.
. .
X3
TO AMPLIFIER
AUDIO OUT
1
X18
1
2
3
4
5
2 IX11 IX10 IX9 IX8 IX7 IX6 IX5 IX4 IX3 IX2 IX1
3 EXT. CON. FOR CHIME
X4
SPA-REL OVERRIDE
1
2
AMPLIFIER
EXTERN
1
3
2
4 1 1
J28
J23
J21
J22
5 2 2
X5 3 3
1 4 4 X15
POTFREE
OUTPUT
PA-MUTE
ALARM INPUT 1
ALARM INPUT 2
2 5 5 1
1
J6
J8
J26
J7
9 9 5
2
VOL.TO AMP. 10 10 2
3 6
11 11 3
7
ENT. OUT 12 12 4
8
AMPLIFIER INPUT
1 3 3 3 1 3 1
2 4 4 4 2 4 2
MICROPHONE INPUT 1
MICROPHONE INPUT 3
3 3
TALK-BACK CTB/ETB INPUT
FUSE 1A
5 5 5 5
F1
4 6 6 6 4 6
X2
PABX INPUT
5 7 7 7 5 7
+
EMERGENCY
6 6 1
8 8 8 8 24 VDC
2 POWER
7 9 9 9 7 9
8 8 3
10 10 10 10
FUSE 1A
X1
F2
9 11 11 11 9 11
10 12 12 12 10 12 + 1
SUPPLY
POWER
24 VDC
11 13 13 13 11 13 2
12 14 14 14 12 14 3
990-552 SPA-TERMINALBOARD V3
J23
J22
ENT. OUT
Audio Input from Talk-Back X7
TALK BACK
Jumper J17 in upperENT. VOL
position (default setting):
INT./EXT. 24V OVERRIDE
INT. - EXT. - Audio from the Talk-back unit is connected to minus.
Figure 7 Jumper for audio from Talk-Back system
- If audio output 0dB from Talk-Back is connected both to SPA and a
100V Talk-Back system, the Jumper J17 must be set to the lower
ZONE ALL - TB ON/OFF
position.
J28
J21
J23
J22
Alarm Priority
EMS+ALL - EMS ONLY
Default setting:
- Jumper PRIO.1, PRIO.2 and PRIO.3 in upper (N) position, and
J5
J4
J2
J3
J26
J6
J7
J5
J4
J2
J3
Normal priority: ALARM will have 6th priority after Talk-Back,
PRIO.1 PRIO.2
microphones and PABX.
N N N N
UT
J28
J21
J23
J22
Select the zone(s) by setting the jumper(s) to lower position for
activation of audio to ‘External amplifier’ on terminal X4.
ON/OFF EMS+ALL - EMS ONLY
J28
J21
J23
J22
J23
J22
J26
J6
J7
PRIO.1 PRIO.2 At least one zone must be selected (ON) if PABX is used. N / E
N N N N
Figure 11 Jumpers for PBX audio output per zone
J5
J4
ENT. VOL
Zone All – Talk-Back Selection
N / EMS - Set jumper J2 in left position for ZONE ALL and TALK-BACK on.
- Set jumper J2 in right position for TALK-BACK off
ZONE ALL - TB ON/OFF
J28
J21
J23
J22
Emergency selection
- Set jumper J1 in EMS+ALL position for emergency message with
EMS+ALL - EMS ONLY 1st priority.
- Set jumper J1 in EMS ONLY position for normal default priority.
Figure 12 Jumpers for Talk-Back with emergency message
● Normal override
- Zone selection 1 to 6 or only All Call override.
● Emergency override
- Normal and EMS or EMS ONLY override
● Internal or external 24V DC override
J23
J22
volume control.
The default setting is “only EMS will override volume control”.
EMS+ALL - EMS ONLY
Figure 14 Jumpers for override on normal & EMS vs. EMS only
L A maximum of 20 volume control units can be connected when the jumper is set
to internal.
J5
J4
J2
J3
N / EMS
J5
J4
J2
J3
Entertainment output selection
N / EMS
Set jumpers J1 to J6 to ON for Entertainment audio selection for any of
the 6 zones. This setting will be overridden by any messages or alarms.
CHIME CALL
Trim potentiometer marked BGM for audio input adjustment microphone
CHIME
0
input 2.
Trim potentiometer marked CHIME for adjustment of ding-dong signal
0 – 6 + 6
ON OFF
level.
OUT IN
TONE
● For each zone, count the number of loudspeakers and do the power
tappings in accordance with available output power for the zone.
● Make sure to NOT exceed the total amplifier output capacity.
● Power tapping options can be found in the loudspeaker datasheet.
● The type of Volume Control depends on the number of loudspeakers
in a single or A-B system.
GA GA PULSING GA GA GA PULSING GA
PULSING w/ MUTE STEADY PULSING w/ MUTE STEADY
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General Steady LED Pulsing LED Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long Constantly Constantly Blinks Blinks
4 NOT IN USE
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
The MANUAL button is also used to manually generate alarm tone patterns.
2.11.5 Alarm 2
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long Constantly Constantly Blinks Blinks
4 Reset
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
Abandon LED Manual LED MOB LED SPA-AC6 Activation Termination Activation Contact Output
button button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
constantly Button 4 Press and hold Release MOB Latched N/A N/A
2.11.7 Alarm 4
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long blinks constantly blinks blinks
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
constantly Button 4 Press and hold Release MOB Latched N/A N/A
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
Abandon Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
LED button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
constantly Button 4 Press and hold Release MOB Latched N/A N/A
2.11.9 Alarm 6
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
constantly Button 4 Press and hold Release MOB Latched N/A N/A
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
4 Reset
Abandon Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
LED button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
2.11.11 Alarm 8
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
Sequence (sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
4 Reset
Abandon Manual MOB LED SPA-AC6 Activation button Termination Activation Contact Output
LED LED button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
Priority Alarm Type Audio Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
Sequence (sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long blinks constantly blinks blinks
4 Reset
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
2.11.13 Alarm 10
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
4 Reset
Abandon LED Manual MOB LED SPA-AC6 Activation button Termination Activation Contact Output
LED button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
2.11.15 Alarm 12
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
4 Reset
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long constantly constantly blinks blinks
Abandon Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
LED button type
constantly Button 3 Press and hold Release Manual Latched SPA-AL-REL6-V2 Steady
Manual
2.11.17 Alarm 14
L Refer to the SPA-AL-REL-V2 and SPA-REL-V2 figures in section 2.11.2 for the location of the LEDs.
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long Constantly Constantly Blinks Blinks
General2 LED Abandon LED Manual LED SPA-AC6 Activation button Termination Activation Contact Output
button type
Priority Alarm Type Audio Sequence Frequency "Timing Sequence General LED Steady LED Pulsing w. Mute Pulsing w. Mute
(sec)" LED LED
1 General 7 short 1/2 long 800Hz 1s Short, 6s Long Constantly Constantly Blinks Blinks
Abandon LED Manual LED MOB LED SPA-AC6 Activation button Termination Activation Contact Output
button type
N/A N/A
● Check that jumper settings are set in accordance with section 2.8.1
for the main terminal board.
● Check that jumper settings are set in accordance with section 2.8.2 –
2.8.5 for additional function boards.
● Check that the volume for audio input is adjusted in accordance with
section 2.9
Step Requirements
1 Inspection of the following according to section 2.1 - 2.5 :
- Mechanical
- Cable
- Power
- Function configurations
2 System operates on 230V AC main and 24V DC emergency
- Switch on the 230V main power supply and check that we have 24V DC on terminal X1 on the main terminal board.
- Switch on the 24V DC emergency and check that we have 24V DC on terminals X2 on the main terminal board.
Power failure output - SPA-FAIL
- Switch off the 230V AC main and check that the power failure output is activated when the system operates on 24V DC
Emergency
L If other signal levels are required after installation, adjust the signal by using trimming potentiometer marked
P1 CTB/ETB VOL for audio from Talk-Back System on main terminal board, block X7
Additional function boards for the SPA system
14 Ding-dong chime generation - SPA-CHIME-V2
This multiple chime generator has a setting for tone.
- Set the required tone by operating the potentiometer for tone selection.
- Set the tone level to 40 VAC by operating the potentiometer for volume setting.
15 Start entertainment unit - SPA-RCD
- Switch on “ENTERTAINMENT ON/OFF”
- Follow user instructions for delivered model.
16 Start Entertainment monitor/control unit - SPA-SWITCH-V2
This unit has an adjustable preamplifier.
- For system with entertainment sources such as SPA-RCD6, SPA FM/AM
- Follow instructions in the SPA-V2 User Manual.
17 Interface to external system – SPA-EMS-V2
Additional terminal board for interface Emergency PA and alarm to external system set by jumpers.
- Test that only EMS and Alarm activate Emergency output signal 0 dB and potential-free contact to external system J1 – X80
- Test that EMS and ALL CALL, and alarm activate Emergency output signal 0 dB and potential-free contact to external system
J1 – X80
18 Make a PA message using digital message recorder unit combined with remote panel SPA-REM7
- See separate instructions for digital message recorder unit
19 Test of 4-way volume control function (Override) - use board SPA-MUL-V2
Follow instructions in the SPA-V2 User Manual.
Volume Override can be changed via jumper settings:
- PA override by zone selection or only “All Call” is set with jumper J24 on the main terminal board
- For EMS or PA and EMS ONLY volume control override is set with jumpers J37/J7 on the SPA-MUL-V2 / SPA-ENT4-V2 board
L Warning: Do not exceed 50mA for the cable and relay as this will cause the
system to become unstable.
ON
LATCHED START ON
frequency
(Hz)
1.5K
1K
1s 1s 1s 1s 1s 1s 1s 3s 1s
800
500
1s 1s 1s 1s 1s 1s 1s 1s
0 time (s)
frequency
(Hz)
805
800
1s
0 time (s)
frequency
(Hz)
MANUAL / FIRE
1.5K
1K
continuous signal
800
500
0 time (s)
1K
1s 1s 1s 1s 1s 1s 1s 1s 1s 1s
800
500
1s 1s 1s 1s 1s 1s 1s 1s 1s
0 time (s)
frequency
(Hz) MUSTER / ABANDON (NORSOK/PFEER)
repeat
sequence
1.5K
1.2K
1K
500
1s 1s 1s 1s 1s 1s 1s 1s 1s
0 time (s)
frequency
(Hz) GENERAL ALARM (NORSOK/PFEER)
repeat
sequence
1.5K
1s 1s 1s 1s 1s 1s 1s 1s 1s 1s
1K
500
1s 1s 1s 1s 1s 1s 1s 1s 1s
0 time (s)
frequency
(Hz) TOXIC GAS (NORSOK)
repeat
sequence
1.5K
1s
1K
500
1s
0 time (s)
frequency
(Hz) TOXIC GAS (PFEER)
1.5K
continuous signal
1K
500
0 time (s)
The WEEE Directive does not legislate that Zenitel, as a ‘producer’, shall collect ‘end of life’
WEEE.
This ‘end of life’ WEEE should be recycled appropriately by the owner who should use proper
treatment and recycling measures. It should not be disposed to landfill.
Many electrical items that we throw away can be repaired or recycled. Recycling items helps to save our
natural finite resources and also reduces the environmental and health risks associated with sending electrical
goods to landfill.
Under the WEEE Regulations, all new electrical goods should now be marked with the
crossed-out wheeled bin symbol shown.
Goods are marked with this symbol to show that they were produced after 13th August 2005,
and should be disposed of separately from normal household waste so that they can be
recycled.
DOC NO.
A100K10370 customer.service@zenitel.com
Zenitel and its subsidiaries assume no responsibility for any errors that may appear in this publication, or for damages arising from the information therein. Vingtor-Stentofon and Phontech products are developed and marketed
by Zenitel. The company’s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001. Zenitel reserves the right to modify designs and alter specifications without notice.
ZENITEL PROPRIETARY. This document and its supplementing elements, contain Zenitel or third party information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited, if not otherwise
explicitly agreed in writing with Zenitel. Any authorized reproduction, in part or in whole, must include this legend: Zenitel – All rights reserved.