Professional Documents
Culture Documents
Study Guide: Electronic Products Assembly and Servicing Ncii
Study Guide: Electronic Products Assembly and Servicing Ncii
Prepared by:
Marollano, Edgar
Mabansay, John Raymund
Carretero, Jayben
INTRODUCTION
A: Prepare to assemble electronic products
This course is designed to enhance your skills, positive attitude and work values in
accordance with the prevailing standards in the TVET sector. This encompasses required to:
OBJECTIVES
KEY CONCEPTS
A: Prepare to assemble electronic products
1. OHS Policies
2. Risk control
3. Work Coordination
4. Inventory
B:
1. PCB Theory and Characteristics
2. PCB Problems and Solutions
3. PCB Manufacturing
a. PCB Manufacturing Information
b. PCB Layout and Artwork
4. Component Layout and Grounding
5. Surface Mount Components and Devices
6. Through-Hole Mount Components and Devices
7. Design Compliance With EMI / EMC
8. Coatings
9. Thermal and Vibration Theories
10. PCB Fabrication
a. Blanking, Cutting, Punching, Drilling
b. Laminating Techniques
c. Plating, Etching, Surface Finishing
11. Environmental Control
C:
1. The different hand tools
Screw driver nut driver
Wrench hex key
Pliers paint brush
Hammer puncher
S T U D Y GU I D E
ELECTRONIC PRODUCTS ASSEMBLY and SERVICING NCII
28 Hours
B L E N D E D T R A I N I N G
CARRETEROMAROLLANOMABANSAY
File file
Disoldering pump
2. The different power tools
LEARNING RESOURCES
A:
1. GroB Electronics
2. Online Resources
3. CBLM
B:
STUDY QUESTIONS
A:
1. What is OHS Policy? What are the procedures involved in this policy?
2. Identify some risk control measures in your work area
3. Why do we need to consult responsible person for safety matters?
4. How are you going to conduct inventory?
B:
1. What strategy you need to develop in order to have a good PCB Module?
2. What safety precautions you need to observed in preparing PCB Module?
3. What is Through Hole soldering?
4. What are the steps in resting the assembled PCB Module?
C:
1. What is a hand tools?
2. What is power tools?
3. What are the different kinds of screwdriver?
Online Activities
A:
1. Webinar
2. Computer Based Test
1. B: Enrollment to the Online Module for EPAS NC II: Assemble Electronic Products
2. Orientation to the blended learning program
3. Participate in the Getting to Know You Discussion Forum and take the Pretest
4. Read lessons under Unit 1: Prepare/make PCB Modules
5. Read PCB Theory and Characteristics
6. Read PCB Problems and Solutions
7. Read PCB Manufacturing
8. Answer Quiz No. 1.1
9. Watch video No. 1
10. Read Component Layout and Grounding
11. Read Surface Mount Components and Devices
12. Read Through-Hole Mount Components and Devices
13. Read Design Compliance With EMI / EMC
14. Watch video No. 2
15. Answer Quiz No. 1.2
16. Read Coatings
17. Read Thermal and Vibration Theories
18. Read PCB Fabrication
19. Read Environmental Control
20. Watch video No. 3
21. Answer Quiz No. 1.3
22. Complete Task Sheet 1.4
23. Practice of task/job activities and oral questioning
24. Answer posttest in Unit 1: Prepare/make PCB Modules
25. Take Institutional Assessment under Unit 1: Prepare/make PCB Modules
C:
1. Enrollment to the Online Module for EPAS NC II: Service Consumer electronic, products, and
systems
2. Participate in the Getting to Know You Discussion Forum and take the Pretest
3. Read lessons under Unit 1:
4. Complete Activity No. 1
5. Watch video No. 1
S T U D Y GU I D E
ELECTRONIC PRODUCTS ASSEMBLY and SERVICING NCII
28 Hours
B L E N D E D T R A I N I N G
CARRETEROMAROLLANOMABANSAY
Offline Activities
A:
1. Knowledge enrichment thru reading downloaded LMs
2. Perform Tasks/Activities
B:
1. Reading Learning resources downloaded from LMS
2. Practice of task/job activities and oral questioning
C:
1. Orientation to the blended learning program
2. Demonstration and assessment of task/job activities and oral questioning
3. Mentoring and coaching
4. Institutional Assessment (After passing all the modules under the cluster COC 2: Install consumer
electronic products and systems)
STUDY SCHEDULE
Please refer to the schedule for your reference
A:
Inventory
July 6, 2020 Task sheet online 1
July 6, 2020 Computer 30 item - Quiz Online 2
based Test
B:
1.1 LMS
Watch video No. 1 Online 3 min
LMS
Component Read Component offline 45 min
Layout and Layout and
Grounding Grounding
Surface Mount Read Surface offline 45 min
Components Mount
and Devices Components and
Devices
Through-Hole Read Through- offline 45 min
Mount Hole Mount
Components Components and
and Devices Devices
With EMI / Read Design offline 45 min
EMC Compliance With
EMI / EMC
Watch video No. 2 Online 3 min
LMS
Answer Quiz No. Online 3 min
1.2 LMS
Coatings Read Coatings offline 45 min
Thermal and Read Thermal and offline 45 min
Vibration Vibration Theories
Theories
PCB Read PCB offline 45 min
Fabrication Fabrication
Environmental Read offline 45 min
Control Environmental
Control
Watch video No. 3 Online 3 min
LMS
Answer Quiz No. Online 5 min
1.3 LMS
Complete Task Online 5 min
S T U D Y GU I D E
ELECTRONIC PRODUCTS ASSEMBLY and SERVICING NCII
28 Hours
B L E N D E D T R A I N I N G
CARRETEROMAROLLANOMABANSAY
C:
REFERENCES:
A:
Grob Electronics, CBLM
B:
Competency Based Learning Module, Competency Based Curriculum, and Training
Regulation, LMS and YouTube.
C:
CBLM