Professional Documents
Culture Documents
INSTALLATION MANUAL
Applied Machine: FS-519
12. Screw C
1. Saddle unit 9
(4 × 8 mm)
4511U012AA
1 13. Screw D
(3 × 8 mm) 1
9735
14. Screw E
4511IXC107DA
(4 × 8 mm) 1
2. Creasing unit 9J08IXC079DA
15. Shoulder
1 1
screw A 4511U013AA
4511IXC055DA
16. Shoulder
screw B 2
3. Exit tray 4511U014AA
17. Installation
1 manual
1
4511U004AA set
4. Shutter
4980IXC019DA
1
4511IXC024DA
5. Mounting
bracket (right) 1
After unpacking, be sure to get rid of the
4511U006AA packaging materials and keep them out of
6. Mounting the reach of children.
bracket (left) 1 Putting the head in the plastic bag
4511U007AA involves danger of suffocation.
7. Shutter
mounting 2
holder
4511U008AA
8. Creasing unit
adjusting plate
1
4511U009AA
4511-9560-00
E-1
II. Installation procedures 3. If the finisher is mounted on the machine, remove
the finisher.
Note: Note:
• When mounting the saddle sticher, mount it For the finisher removal procedure, see installa-
before mounting the finisher to the machine. tion manual for finisher.
• When mounting the punch kit at the same time,
4. Remove the rear cover of the finisher (four
mount the punch kit first.
screws).
1. Turn off the machine and unplug the power cord 5. Disconnect the connector.
from the power outlet.
2. Remove the saddle unit and all other accessories
from the shipping carton and remove the protec-
tive tape and cushioning materials.
<Saddle unit>
4512IXC080DA
4511IXC108DA
<Creasing unit>
4511IXC058DB
4511IXC123DA
<Exit tray>
4512IXC040DB
E-2
9. Remove the guide plate (left) (two screws). 11. Let the connector of the creasing unit into the
Note: hole shown in the illustration.
When mounting the punch kit at that time, it has 12. Carefully insert the creasing unit into the finisher
been removed. along the notch provided in the rear of the fin-
isher.
Note:
Use care not to allow the parts shown in the illus-
tration to hit against the mating portions while the
creasing unit is being inserted.
Insert it with the guide plate at the finisher side fac-
ing downward shown “OK” in the illustration.
Notch
4511IXC059DB
Parts
Hole
4511IXC060DB
NG
OK
4511IXC082DB
E-3
13. Place the creasing unit adjusting plate beneath 17. Connect the connector of the creasing unit.
the creasing unit and temporarily secure the unit
by tightening screw only temporarily (one screw
A furnished with saddle sticher).
4511IXC083DA
4512IXC054DA
4511IXC063DB
4511IXC062DB
E-4
20. Reconnect the connector that has been discon- 25. Move the shutter up and down. Release the
nected in step 5. shutter from a higher position to check to ensure
21. Reinstall the rear cover that has been removed that the shutter falls by its own weight.
in step 4 (four screws). * If it does not fall by its own weight, move the
shutter up and loosen the screw of the shutter
mounting holder which can be seen from the
hole shown on the picture, and adjust the posi-
tion of the shoulder screw B.
4512IXC084DA
4511IXC109DA
4511IXC110DA
4511IXC113DA
E-5
28. Remove the right and left covers (two screws 31. Secure the mounting brackets in position follow-
each). ing the order shown in the illustration (three
screw C’s each furnished with the saddle
sticher).
3 3
1 1
4511IXC114DA 2
2
29. Use a nipper, etc. to cut out two separation cov- 4511IXC071DA
ers.
32. Reinstall the right and left covers that has been
removed in step 28 (two screws each).
4510IXC029DA
Note:
Make sure that the flat surface of each of the 33. Loosen the screw shown, move it to the front,
mounting brackets faces inward when installed. and then tighten it again (one screw).
Note:
• This step must be performed properly to pre-
vent any trouble.
• Do not move the screw by using the adjust
plate.
• Be sure to move the screw itself.
4511IXC115DA
Adjust plate
4511IXC117DA
E-6
34. Reinstall the left exit tray mounting holder that 37. Reinstall the finisher exit tray that has been
has been removed in step 27 (one screw). removed in step 26 (two screws).
Note:
Install the holder at a level one step lower than
where it was removed in step 27.
4511IXC118DA
4510IXC032DA
4511IXC086DA
E-7
39. Secure the saddle unit to the mounting bracket 43. Remove the connector cover from the finisher
(left) (two screw C’s furnished with the saddle (one screw).
sticher). 44. Use a nipper, etc. to cut out the separation
Note: cover.
Temporarily tighten the left screw, securely tighten
the right screw, and then securely tighten the left
screw.
Right
Left
4511IXC078DA
4511IXC052DA
4511IXC121DA
E-8
III. Adjustments <Crease position adjustment>
1. Make a copy in the crease mode.
* State the adjustments of A3 here. (Refer to the user’s guide (copy operations))
1. Plug the power cord into the power outlet and 2. Fold the copy fed out along the crease.
turn on the machine. 3. Check the crease for deviation (measure width
<Crease tilt adjustment> A).
Reference: 0 ± 1.5 mm
2. Load the drawer with A3 .
3. Select the crease mode and make a copy. A
(Refer to the user’s guide (copy operations))
4. Fold the copy fed out along the crease.
5. Fold the copy fed out in half.
6. Check the crease for tilt (measure width A).
Reference: 0 ± 1.5 mm
A
Center
Exit direction
4511IXC090DA
Crease
4. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
5. Touch “Finisher.”
Exit direction 4511IXC089DA
A00JIXE118DA
4511IXC122DA
4512IXE075DA
E-9
7. Touch “Fold&Staple Pos. Adjustment.” [If the crease deviates as shown below]
11. Using the key, set the numeric value and
touch “END.”
A
4512IXE077DA
Exit direction
8. Touch “Fold Position Adjustment.” 4511IXC091DA
4511IXE104DA
4511IXE105DA
Exit direction
4511IXC090DA
E-10
<Staple tilt adjustment> <Staple position adjustment>
1. Load a five-page A4 document in the docu- 1. Load a five-page A4 document in the docu-
ment feeding tray. ment feeding tray.
2. Select the center staple mode and make a copy. 2. Select the center staple mode and make a copy.
(Refer to the user’s guide (copy operations)) (Refer to the user’s guide (copy operations))
3. Fold the copy fed out along the crease. 3. Fold the copy fed out along the crease.
4. Check the staple positions for tilt (measure width 4. Check the staple position for deviation from the
A). crease (measure width A).
Reference: 0 ± 1.5 mm Reference: 0 ± 1.5 mm
A A
Exit direction
4511IXC092DA
Exit direction 4511IXC093DA
5. Open the saddle unit lock release lever. 5. Display the Service Mode screen.
6. Loosen the adjusting screw and move the saddle (For details of how to display the Service Mode
to the left or right to adjust tilt as necessary. screen, see the service manual.)
* If the staple positions tilt as in step 4, move the 6. Touch “Finisher.”
saddle to the left as shown below.
A00JIXE118DA
4511IXC054DA
4512IXE075DA
E-11
8. Touch “Fold&Staple Pos. Adjustment.” [If the staple positions deviate as shown below]
12. Using the key, set the numeric value and
touch “END.”
A
4512IXE077DA
4511IXE104DA
4511IXE106DA
Exit direction
4511IXC093DA
E-12