Professional Documents
Culture Documents
INSTALLATION MANUAL
Applied Machine: FS-533
A3EUIXC004DA
5. Front cover
1
Locked Unlocked
A3EUIXC031DA
A3EUIXC005DA
6. Screw A
(3 × 6 mm) 2 • If the punching unit is open, do not carry the
9654 front.
7. Screw B
(3 × 6 mm) 1
9735
8. Installation
manual
1
set
4980IXC019DA
A3EU-9550-00
E-1
II. Installation procedures 5. Attach the supplied stopper pin to the paper feed
side of the finisher at the position shown in the
Note: illustration. (One supplied screw A)
When mounting the punch kit, mount it before
mounting the finisher to the main unit.
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove protective tape and shipping materials
and take out accessory parts.
A3EUIXC008DA
A3EUIXC009DA
A3EUIXC010DA
A3EUIXC007DA
E-2
8. Remove the screw shown in the illustration from 11. Remove the lock part from the back of the fin-
the finisher. isher, then install by sliding in the “ PK” direc-
tion. (One screw)
A3EUIXC014DA
A3EUIXC011DA
A3EUIXC016DA
14. Fit the two tabs on the finisher into the rectangu-
lar holes on the punch unit.
Tab
A3EUIXC012DA
A3EUIXC017DA
E-3
15. Secure the punch unit with the supplied screw B. 18. Reattach the cover removed in step 6 to the fin-
isher. (Three screws)
Note:
Hook the tab on the plate to the cover.
A3EUIXC018DA
Front cover
A3EUIXC022DA
A3EUIXC019DA
17. Align the slit of the stopper arm with the pin on 20. Mount the finisher to the main unit.
the stopper pin so that the punch unit is secured Note:
to the finisher. • For the finisher mounting procedures, see
installation manual for finisher FS-533.
• Before installing the finisher, be sure to check
that the punch unit is securely locked into the
finisher.
• Do not install the rail cover supplied with the fin-
isher. (The cover is unnecessary, so discard it.)
21. Slide the finisher out by pulling its lever.
A3EUIXC020DA
E-4
22. Attach the supplied rail cover to the finisher. (3) Secure the rail cover with the screw (front side)
(1) Set the rail cover at the end of the rail. and the shoulder screw (rear side).
Note: Note:
Make the finisher’s harness come out from the rail Use the shoulder screw and the screw supplied
cover at the position shown in the illustration. with the finisher.
A3EUIXC024DB
A3EUIXC025DA
A3EUIXC026DA
A3EUIXC033DA
E-5
IV. Punch option setting 3. Slide the finisher by pulling its lever.
4. Remove the C-clip and remove the lever shown
1. Plug the power cord into the power outlet and in the illustration from the punch unit.
turn on the machine.
2. Display the Service Mode screen. (For details of
how to display the Service Mode screen, see the
service manual.)
3. Touch “Finisher.”
4. Touch “Punch option setting.”
5. Touch “PK-519” and select a desired number of
holes.
6. Touch “decision.”
7. Touch “END.”
8. Touch “Exit” on the Service Mode screen.
9. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
A3EUIXC027DA
Mode screen and wait for 10 seconds or more
before turning on.
5. Remove the cover shown in the illustration from
the punch unit. (One screw)
A3EUIXC028DA
A10EIXC018DA
A3EUIXC029DA
E-6
7. Move the punch unit back and forth to adjust its
position, referring to the guide lines.
A3EUIXC030DA
E-7