Professional Documents
Culture Documents
Outer mirror
cardiagn.com
MX-10
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MX-11
Outer mirror switch
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MX-13
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MX-13
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MX-14
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MX-14
Relay
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MX-16
MX
MX–2 Outer mirror - Electric mirror system
Parts location
For automatic air conditioning system : Except for automatic air conditioning system :
cardiagn.com
Rear window defogger switch Rear window defogger switch
Outer rear-view
Engine compartment relay block ASSY mirror ASSY RH
MX
Instrument panel junction block ASSY
- HEATER fuse
Outer mirror - ECM ACC fuse
switch ASSY
Outer rear-view
mirror ASSY LH
GW-10136
Outer mirror - Electric mirror system
MX–3
Symptom table
General
Symptoms Inspection items Reference pages
MIR HTR fuse -
MIR HTR relay -
Mirror heater doesn't operate. (Window defogger system oper-
Outer rear-view mirror ASSY RH MX - 8
ates normally)
Outer rear-view mirror ASSY LH MX - 8
Vehicle wiring harness and connector -
Mirror heater doesn't operate. (Window defogger system also
See the rear window defogger system WS - 89
doesn't operate)
cardiagn.com
MX
MX–4 Outer mirror - Outer rear-view mirror
Exploded view
7.5 {76,5.5}
cardiagn.com
Butyl tape
MX Non-reusable parts
GW-01212
Outer mirror - Outer rear-view mirror
MX–5
Outer mirror LH
cardiagn.com
Outer mirror cover LWR LH
GW-01213
Removal
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH and LH side.
1. Removal of the door armrest cover LH (Refer to DH - 32)
2. Removal of the front door trim board SUB-ASSY LH (Refer to DH - 32)
3. Removal of the front door service hole cover LH (Refer to DH - 36)
4. Removal of the outer mirror cover LWR LH
(1) Retract the outer rear-view mirror LH.
MX
MX–6 Outer mirror - Outer rear-view mirror
$
GW-01214
cardiagn.com
(2) Remove the 3 bolts and remove the outer rear-view mirror LH.
Disassembly
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH and LH side.
1. Removal of the outer mirror LH (Refer to MX - 10)
2. Removal of the outer mirror cover LH
*1
GW-01361
Outer mirror - Outer rear-view mirror
MX–7
GW-01362
(4) Slowly slide the molding remover in the direction of an arrow, and
*3 remove the engaged tabs to remove the outer mirror cover LH.
Captions in illustration
*1 Protective tape
*2 Molding remover
*1
*3 tabs
cardiagn.com
*2
GW-01363
Assembly
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH and LH side.
1. Installation of the outer mirror LH (Refer to MX - 11)
2. Installation of the outer mirror cover LH
(1) Fit in the 6 tabs and install the outer mirror cover LH.
MX
Installation
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH and LH side.
1. Installation of the outer rear-view mirror LH
(1) Retract the outer rear-view mirror LH.
(2) Using 3 bolts, install the outer rear view mirror LH.
Standard value:T=7.5N·m {76kgf·cm} {5.5ft·lbf}
MX–8 Outer mirror - Outer rear-view mirror
(3) Align the alignment mark of the wiring harness with the harness
clip on the body side, and install the wiring harness.
Captions in illustration
*1 Alignment marks
EB-00918
cardiagn.com
4. Installation of the front door trim board SUB-ASSY LH (Refer to DH - 52)
5. Installation of the door armrest cover LH (Refer to DH - 54)
Unit inspection
1. Inspection of the outer rear-view mirror RH
(1) Operation inspection for the mirror surface position
(a)Inspect operation when battery voltage is applied between con-
nector terminals.
Criteria
Battery connection Operation direction
Battery positive →3 (MR+)
Upward
Battery ground →8 (MV)
/* /8 Captions in illustration
MX GW-01232
*a
Connector not connected
(Outer rear-view mirror RH)
(2) Inspection for the mirror heater (when there is a mirror heater)
(a)Measure the resistance according to the following chart.
Resistance
Inspection terminals (Termi-
Inspection conditions Standard value
nal symbol)
4 (+) - 10 (-) 23°C {73°F} 9.6 to 14.4 Ω
Outer mirror - Outer rear-view mirror
MX–9
Captions in illustration
/* /8
GW-01233 Connector not connected
*a
(Outer rear-view mirror LH)
(2) Inspection for the mirror heater (when there is a mirror heater)
(a)Measure the resistance according to the following chart.
Resistance
cardiagn.com
Inspection terminals (Termi-
Inspection conditions Standard value
nal symbol)
4 (+) - 10 (-) 23°C {73°F} 9.6 to 14.4 Ω
MX
MX–10 Outer mirror - Outer rear-view mirror glass
Exploded view
Outer mirror LH
cardiagn.com
GW-01215
Removal
NOTE:
MX The following procedure is for LH side. Perform the same procedures for the RH and LH side.
1. Removal of the outer mirror LH
(1) As shown in the figure, tilt the outer rear-view mirror LH in the for-
ward retracting direction.
Outer mirror - Outer rear-view mirror glass
MX–11
(2) Push the inside of the mirror surface and face the mirror surface
towards the interior of the vehicle.
(3) Apply protective tape to the location in the figure.
Captions in illustration
*1 Protective tape
GW-01216
cardiagn.com
GW-01217
GW-01218
GW-01219
Installation
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH and LH side.
MX–12 Outer mirror - Outer rear-view mirror glass
(3) Fit in the 2 tabs and install the outer mirror LH.
CAUTION:
Be careful not to push the outer rear-view mirror glass with excessive
force, as this may crack the mirror.
cardiagn.com
GW-01220
(4) Push the outer rear-view mirror LH in the direction shown in the
figure.
MX
Outer mirror - Outer mirror switch
MX–13
Exploded view
cardiagn.com
x2
x4
Power window regulator master switch ASSY Outer mirror switch ASSY
w/ front armrest base panel UPR LH
GW-01221
MX
Removal
1. Removal of the door armrest cover LH (Refer to DH - 32)
2. Removal of the front door trim board SUB-ASSY LH (Refer to DH - 32)
3. Removal of the power window regulator master switch ASSY W/ front armrest base panel UPR LH (Refer to DH - 33)
MX–14 Outer mirror - Outer mirror switch
*1 Protective tape
GW-01557
Installation
1. Installation of the outer mirror switch ASSY
(1) Fit in the 4 tabs and install the outer mirror switch ASSY.
cardiagn.com
GW-01556
2. Installation of the power window regulator master switch ASSY W/ front armrest base panel UPR LH (Refer to DH - 52)
3. Installation of the front door trim board SUB-ASSY LH (Refer to DH - 52)
4. Installation of the door armrest cover LH (Refer to DH - 54)
Unit inspection
1. Inspection of the outer mirror switch ASSY
*a (1) Resistance check
*1
(a)Measure the resistance between connector terminals when
each switch is operated.
Resistance
Positioning switch (Side to side changing switch, left side)
Inspection terminals (Terminal symbol) Inspection conditions Standard value
1 (B) - 14 (ML+)
Hold down the "Up" switch Less than 1 Ω
10 (VL) - 7 (E)
1 (B) - 10 (VL) Hold down the "Down"
Less than 1 Ω
MX *2 14 (ML+) - 7 (E)
1 (B) - 8 (HL)
switch
Hold down the "Left"
Less than 1 Ω
14 (ML+) - 7 (E) switch
E B
1 (B) - 14 (ML+) Hold down the "Right"
Less than 1 Ω
8 (HL) - 7 (E) switch
7 6 5 4 3 2 1 Resistance
Positioning switch (Side to side changing switch, right side)
16 15 14 13 12 11 10 9 8 Inspection terminals (Terminal symbol) Inspection conditions Standard value
1 (B) - 12 (MR+)
Hold down the "Up" switch Less than 1 Ω
11 (VR) - 7 (E)
1 (B) - 11 (VR) Hold down the "Down"
ML+ MR+ VR VL HR HL Less than 1 Ω
12 (MR+) - 7 (E) switch
1 (B) - 9 (HR) Hold down the "Left"
Less than 1 Ω
12 (MR+) - 7 (E) switch
1 (B) - 12 (MR+) Hold down the "Right"
Less than 1 Ω
9 (HR) - 7 (E) switch
Outer mirror - Outer mirror switch
MX–15
Captions in illustration
*1 Positioning switch
*2 Side to side changing switch
Connector not connected
*a
(Outer mirror switch ASSY)
cardiagn.com
MX
MX–16 Outer mirror - Relay
Relay
Exterior
Outer mirror
body & electrical
Unit inspection
1. Inspection of the MIR HTR relay
C (1) Measure the resistance between connector terminals.
Resistance
Inspection terminals Inspection conditions Standard value
When battery voltage is not applied between
10 kΩ or more
terminals 1 and 2.
3-5
When battery voltage is applied between termi-
Less than 1 Ω
nals 1 and 2.
Captions in illustration
Relay not connected
*a
(MIR HTR relay)
MX cardiagn.com