Professional Documents
Culture Documents
Seat belt
cardiagn.com
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-19
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-19
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-20
Front seat inner belt ASSY
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-21
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-21
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-23
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-24
Front seat outer belt ASSY SB
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-25
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-26
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-27
Rear seat inner belt ASSY
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-29
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-29
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-30
Rear seat outer belt ASSY
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-31
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-31
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-32
Child seat restraining device (ISO-FIX)
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-34
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-36
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-36
Child seat fixing device (ISO-FIX)
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-38
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-39
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SB-39
SB–2 Seat belt - Seat belt warning system
PARTS LOCATION
- MPX-B FUSE
- DOME FUSE
- IG2 FUSE
- DCC FUSE
cardiagn.com
SB
Seat belt - Seat belt warning system
SB–3
- GAUGE FUSE
- RADIO FUSE
cardiagn.com
BELT ASSEMBLY LH CLOCK ASSEMBLY
SB
SB-00538
SB–4 Seat belt - Seat belt warning system
Circuit figure
1 B
from Battery
MPX-B
LED Driver
12 10
from LAPB
Battery DCC DOME 6 13 P/SB
LAPL I/F
8
GND
11 14
from ACC2 GND
RADIO Drive Circuit
Relay
cardiagn.com
D18
Clock Assembly Buzzer
CPU
2 1 37 DBKL
I/F
H19
Front Seat Inner Belt Assembly LH
20 ES1
SB 40 ES2
D7
Combination Meter Assembly
SB-00465
Seat belt - Seat belt warning system
SB–5
1
A/B MAIN IG2
from IG2
Relay
Occupant Detection
Sensor
cardiagn.com
Belt Assembly RH
CPU
16 15
2 38 PBKL
G19 FSR+ PBE D27 I/F
24
3
G19 FSR-
D7
Combination Meter Assembly
:CAN Communication Line
SB-10092
Communication Table
Sender Receiver Signal Communication Method
Airbag control module Combination meter assembly Occupant detection
CAN
Skid control ECM Combination meter assembly Vehicle speed
Description of functions
1. Description of the seat belt warning system
(1) Driver's seat belt warning light:
If the driver's seat belt is not fastened with IG ON, the front seat belt warning light in the combination meter ASSY will
blink to warn the driver. The combination meter ASSY displays the status of the driver's seat belt and the vehicle speed.
(2) Passenger's seat belt warning light:
SB–6 Seat belt - Seat belt warning system
If the passenger's seat belt is not fastened with IG ON and the passenger's seat occupied, the front seat belt warning
light in the clock ASSY will blink. The combination meter ASSY detects the status of the passenger's seat belt and
whether the passenger's seat is occupied or not.
(3) Seat belt warning buzzer:
Check that the seat belt warning buzzer in the combination meter ASSY sounds at 1.2 second intervals for 6 seconds if
the driver's seat belt is not fastened within 1.8 seconds after the ignition switch is turned to ON. If the vehicle speed
exceeds 20 km/h with the passenger's seat occupied and the driver's or the passenger's seat belt not fastened, the seat
belt warning buzzer in the combination meter ASSY will sound once. If 24 seconds have passed after the buzzer starts
sounding, the seat belt warning buzzer in the combination meter ASSY sounds at 1.2 second intervals and continues to
sound for 9.6 seconds. After that, it sounds intermittently at 0.4 second intervals for approx. 20 seconds.
2. Functions of the main parts
Parts Function
Transmits the status information concerning the driver's seat belt (fastened or
Front seat inner belt (driver's buckle switch)
unfastened) to the combination meter ASSY.
Transmits the status information concerning the passenger's seat belt (fastened
Front seat inner belt (passenger's buckle switch)
or unfastened) to the occupant detection ECM.
Transmits the status information concerning the passenger's seat (occupied or
Occupant detection sensor
not occupied) to the occupant detection ECM.
Sends the passenger's seat belt buckle switch signal and the occupant detection
Occupant detection ECM
signal to the airbag sensor ASSY.
cardiagn.com
Sends the passenger's seat belt buckle switch signal to the combination meter
Airbag control module
ASSY.
If the driver's seat belt is not fastened with IG ON, the combination meter will
Driver's seat belt warning light make the seat belt warning light in the combination meter ASSY blink as a
reminder.
If the passenger's seat belt is not fastened with IG ON and the passenger's seat
Passenger's seat belt warning light occupied, the combination meter will make the seat belt warning light in the tell
taillight ASSY blink as a reminder.
If the vehicle speed exceeds 20 km/h (12.5 mph) with one of the following condi-
tions met, the buzzer in the combination meter ASSY will sound as a reminder:
Seat belt warning buzzer 1. The driver's seat belt is not fastened.
SB 2. The passenger's seat is occupied and the passenger's seat belt is not fas-
tened.
Sends the vehicle speed signal to the combination meter ASSY via CAN com-
Skid control ECM
munication.
NEXT
Standard voltage: 11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceed-
ing to the next step.
NEXT
Seat belt - Seat belt warning system
SB–7
(1) Use the SSM4 to check if the CAN communication system is function-
ing normally.
Result:
Result Proceed to
DTC is not output A
DTC is output B
Result:
Result Proceed to
cardiagn.com
Fault is not listed in problem symp-
A
toms table
Fault is listed in problem symptoms
B
table
B Go to step 6
NEXT
6 REPAIR OR REPLACE
NEXT
7 CONFIRMATION TEST
NEXT
END
Operation check
1. Inspection of the driver's seat belt warning light
(1) Turn the ignition switch to ON.
(2) Check that the front seat belt warning light in the combination meter ASSY blinks when the driver's seat belt is not fas-
tened.
SB–8 Seat belt - Seat belt warning system
cardiagn.com
buzzer sounds again.
(7) After the buzzer stops sounding, insert the driver's and passenger's seat belt tongue plates in the buckles. Drive the vehi-
cle at approx. 20 km/h or above, unfasten the driver's or passenger's seat belt, and check that the buzzer sounds again.
(8) After the buzzer stops sounding, change the shift position to R, and then to D. With the seat belt tongue plate not
inserted in the buckle, drive the vehicle at approx. 20 km/h or above, and check that the buzzer sounds again.
CUSTOMIZE PARAMETERS
1. CUSTOMIZE SEAT BELT WARNING SYSTEM
NOTE:
SB The following items can be customized.
CAUTION:
• When the customer requests a change in a function, first make sure that the function can be customized.
• Be sure to make a note of the current settings before customizing.
• When troubleshooting a function, first make sure that the function is set to the default setting.
• These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).
(1) Customizing with the SSM4
(a)Connect the SSM4 to the DLC3.
(b)Turn the ignition switch to ON.
(c) Turn the SSM4 on.
(d)Enter the following menus: [Each System] / [Combination Meter] / [Customize]
(e)Select the setting by referring to the table below.
Warning
Display Default Content Setting Relevant ECU
Driver Side Seatbelt
ON Function to sound the driver seat belt warning buzzer ON/OFF
Warning Buzzer Combination meter
Front Passenger Side Function to sound the front passenger seat belt warning assembly
ON ON/OFF
Seatbelt Warning Buzzer buzzer
NOTE:
This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.
• Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Seat Belt Warning System
Symptom Suspected Area See page
Driver side seat belt warning light does not operate Proceed to "Driver Side Seat Belt Warning Light does not Operate" SB - 11
Airbag system -
Occupant classification system -
Front passenger side seat belt warning light malfunction Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" SB - 13
Front seat inner belt assembly RH -
Combination meter assembly -
Seat belt warning buzzer does not operate Meter/Gauge system -
D7
cardiagn.com
(2) Measure the resistance and voltage according to the value(s) in the table below.
NOTE:
Measure the values on the wire harness side with the connector disconnected.
Tester Connection Wiring Color Terminal Description Condition Specified Condition
D7-1 (+B)- Body ground R-W - Body ground Combination meter +B line Always 11 to 14 V SB
Ignition switch ON 11 to 14 V
D7-2 (IG+) - Body ground W-G - Body ground Combination meter IG line
Ignition switch off Below 1 V
D7-20 (ES1) - Body ground B-Y - Body ground Ground Always Below 1 Ω
Driver seat belt fastened 10 kΩ or higher
D7-37 (DBKL) - Body ground R-B - Body ground Driver seat belt signal
Driver seat belt unfastened Below 1 Ω
D7-40 (ES2) - Body ground B-Y - Body ground Ground Always Below 1 Ω
If the result is not as specified, there may be a malfunction in the wire harness.
(3) Reconnect the D7 combination meter assembly connector.
(4) Measure the voltage according to the value(s) in the table below.
Tester Connection Wiring Color Terminal Description Condition Specified Condition
Front passenger seat occu-
Below 1 V
Front passenger seat belt pied, seat belt fastened
D7-13 (P/SB) - Body ground BR-R - Body ground
warning signal Front passenger seat occu-
11 to 14 V
pied, seat belt unfastened
If the result is not as specified, the combination meter assembly may have a malfunction.
SB–10 Seat belt - Seat belt warning system
AB-10203
cardiagn.com
G19-24 FSR- Occupant detection ECU
G2
Ge1
SB
AB-10993
(4) Enter the following menus: [Each System Check] / [Combination Meter] / [Data monitor], [Each System Check] / [Airbag]
/ [Data monitor], [Each System Check] / [Occupant Detection] / [Data monitor]
(5) Read the Data List according to the display on the SSM4.
Combination Meter (Combination Meter Assembly)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Driver seat belt warning buzzer/ON or
[Driver Side Seatbelt Warning Buzzer] Customized value displayed -
OFF
Front passenger seat belt warning
[P-Seatbelt Warning Buzzer] Customized value displayed -
buzzer/ON or OFF
2. ACTIVE TEST
cardiagn.com
Using the SSM4 to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any
parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before
parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List
information can be displayed while performing Active Tests.
(1) Connect the SSM4 to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the SSM4 on.
(4) Enter the following menus: [Each System Check] / [Combination Meter] / [Active Test]
(5) Perform the Active Test according to the display on the SSM4.
Combination Meter (Combination Meter Assembly)
Tester Display Test Part Control Range Diagnostic Note
SB
[Driver Side Seat Belt] Seat belt warning light OFF/ON -
[Front passenger Side Seat Belt] Seat belt warning light OFF/ON -
WIRING DIAGRAM
2 1 37
DBKL
H19
Front Seat Inner Belt
Assembly LH
D7
Combination Meter
Assembly
INSPECTION PROCEDURE
cardiagn.com
1 PERFORM ACTIVE TEST USING SSM4 (DRIVER SIDE SEAT BELT WARNING LIGHT)
OK
(1) Inspect the front seat inner belt assembly LH (See page SB - 24).
OK
3 CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION
METER ASSEMBLY - BODY GROUND)
(1) Disconnect the H19 front seat inner belt assembly LH connector.
(2) Disconnect the D7 combination meter assembly connector.
(3) Measure the resistance according to the value(s) in the table below.
Seat belt - Seat belt warning system
SB–13
Standard Resistance
Specified Condi-
Tester Connection Condition
tion
D7-37 (DBKL) - H19-1 Always Below 1 Ω
H19-1 - Body ground Always 10 kΩ or higher
H19-2 - Body ground Always Below 1 Ω
OK
cardiagn.com
front seat inner belt ASSY RH and whether the passenger's seat is occupied or not to the airbag control module. The air bag con-
trol module transmits this signal to the combination meter ASSY. According to this signal, the tell taillight ASSY turns on or off the
seat belt warning light in the combination meter ASSY or makes it blink.
SB
SB–14 Seat belt - Seat belt warning system
Circuit figure
10
from IG2 LAPB
Relay GAUGE
13 6
P/SB LAPL
Occupant Detection Sensor
D18
Clock Assembly
16
2
cardiagn.com
FSR+ G19
15
38
PBKL D27 PBE
24
3
FSR- G19
Front Seat Inner Belt
Assembly RH
D7 Airbag Control Module
Combination Meter
Assembly Occupant Detection ECM
SB
Ge1
:CAN Communication Line Front Seat Assembly RH
SB-10093
Inspection steps
CAUTION:
• Before performing the following inspection steps, check the fuses related to this system.
• The seat belt warning system uses the CAN communication system. At first, check that the CAN communication system has no
faults. Refer to the procedures described in "How to troubleshoot." (Refer to SB - 6)
NOTE:
Before performing the troubleshooting, check the fuse of this circuit.
1 Function check
(1) Occupy the driver's seat and the passenger's seat, and unfasten the
seat belts of the both seats.
(2) Turn the ignition switch to ON (engine OFF).
(3) Check that the driver's seat belt warning light in the combination meter
and the passenger's seat belt warning light in the clock turn on and the
buzzer sounds.
Criteria: The buzzer sounds while the warning lights of the driver's
and passenger's seats blink.
NG Go to Step 11.
Seat belt - Seat belt warning system
SB–15
OK
2 Function check
(1) In step 1, wait for the buzzer to stop sounding. (Approx. 6 seconds
after it has started sounding.)
(2) Unfasten and fasten the driver's and passenger's seat belts.
(3) Check that the driver's and passenger's seat belt warning lights turn
on.
Criteria: Each seat belt warning light turns on ←→goes off
according to the operation.
NG Go to Step 7.
OK
3 Function check
(1) In step 2, wait for the buzzer to stop sounding. (Approx. 6 seconds
cardiagn.com
after it has started sounding.)
(2) Start the engine and drive the vehicle at 20 km/h (12 mph) or above.
(3) Check that the driver's and passenger's seat belt warning lights turn on
and the warning buzzer sounds.
Criteria: The buzzer sounds while the warning lights of the driver's
and passenger's seats blink.
NG Go to Step 13.
OK
SB
4 Harness inspection
(1) Disconnect the battery ground terminal, and wait for 60 seconds or
more.
(2) Disconnect the connectors of the combination meter and the seat belt
buckle switch LH.
(3) Check if the harness between the combination meter and the seat belt
buckle switch LH is shorted to the battery, open, or shorted to ground.
OK
SB–16 Seat belt - Seat belt warning system
5 Harness inspection
(1) Measure the resistance between the seat belt buckle switch LH and
the chassis ground.
Resistance
OK
(1) Measure the resistance between the connector terminals of the driver's
seat belt switch when the driver's seat belt is unfastened and fastened.
cardiagn.com
Resistance
SB OK
Replace either the body control module or the combination meter. Or replace both of them. There is the possibility of transmis-
sion error of the body control module or reception error of the combination meter.
NG Go to Step 8.
OK
Go to Step 11.
Seat belt - Seat belt warning system
SB–17
(1) Perform the inspection following the diagnosis procedures for DTC
B1650 of the airbag system. (Refer to RS - 238)
Criteria: No fault is found.
OK
(1) Perform the inspection following the diagnosis procedures for DTC
B1655 of the occupant detection system. (Refer to RS - 240)
Criteria: No fault is found.
cardiagn.com
OK
(1) Perform the inspection for the airbag control module, the occupant
detection sensor, and the seat belt buckle switch RH.
Follow the diagnosis procedures for DTC B16F1 of the airbag system
to perform the inspection. (Refer to RS - 65)
Criteria: No fault is found. SB
NG Repair or replacement of the parts following the proce-
dures for DTC B16F1
OK
OK
OK
cardiagn.com
13 Inspection of the harness between the clock assembly and the combination meter
(1) Disconnect the harnesses from the clock assembly and the combina-
tion meter.
(2) Measure the resistance between the clock assembly and the combina-
tion meter.
Resistance
OK
14 Check of the communication between the clock assembly and the combination meter
(1) Remove the clock assembly, and install a normally functioning clock
assembly (a new clock assembly).
(2) Connect the connectors ((D18) No. 6 - (D7) No. 13) and turn the igni-
tion switch to ON.
Criteria: The clock assembly properly displays the data.
OK
Exploded view
Clock ASSY
x2
cardiagn.com
For manual air conditioning system :
Clock ASSY
LI-10234
Removal
1. Removal of the air conditioner control ASSY (for automatic air conditioning systems) (Refer to AC - 166)
2. Removal of the air conditioner control ASSY (for manual air conditioning systems) (Refer to AC - 170)
3. Removal of the clock ASSY
(1) Release 4 claws and remove the clock ASSY from the air condi-
tioner control ASSY.
Installation
1. Installation of the clock ASSY
(1) Engage 4 claws and install the clock ASSY to the air conditioner control ASSY.
SB–20 Seat belt - Passenger's seat belt warning light
2. Installation of the air conditioner control ASSY (for automatic air conditioning systems) (Refer to AC - 167)
3. Installation of the air conditioner control ASSY (for manual air conditioning systems) (Refer to AC - 174)
Unit inspection
1. Inspection of the clock ASSY
C (1) Check the lighting condition of the passenger's seat belt warning
light when the battery is connected to the connector terminals.
Criteria
Battery connection Criteria
Battery positive →10 The passenger's seat belt warning light turns
Battery ground →6 on.
Captions in illustration
Connector not connected
*a
(Clock ASSY)
cardiagn.com
SB
Seat belt - Front seat inner belt ASSY
SB–21
Exploded view
cardiagn.com
Front seat ASSY LH
42 {428, 31.0} SB
Front seat inner belt ASSY RH Front seat cushion shield INN RH
42 {428, 31.0}
Removal
1. Precautions for handling the device
NOTE:
The following procedure is for LH side. Unless otherwise specified, perform the same procedures for the RH side.
2. Removal of the front seat ASSY LH (Refer to SE - 11)
SB–22 Seat belt - Front seat inner belt ASSY
3. Removal of the front seat cushion shield INN LH (driver's side) (Refer to SE - 13)
4. Removal of the front seat inner belt ASSY LH (driver's side)
(1) Remove the rubber band of the separate type front seat backrest
cover LH.
(2) Release the claw and 3 clamps, and disconnect the wiring harness
of the front seat inner belt ASSY LH.
cardiagn.com
(3) Release the 2 clamps and disconnect the wiring harness of the
front seat inner belt ASSY RH.
(4) Remove the nut and the washer, and remove the front seat inner
belt ASSY RH.
SB
SB-00743
Seat belt - Front seat inner belt ASSY
SB–23
Installation
NOTE:
The following procedure is for LH side. Perform the work for the RH side referring to the procedures for the LH side.
cardiagn.com
1. Installation of the front seat inner belt ASSY LH (driver's side)
(1) Install the front seat inner belt ASSY LH with the nut and the
washer.
Standard value:T=42N·m {428kgf·cm} {31.0ft·lbf}
CAUTION:
• Be careful not to allow the front seat inner belt ASSY LH ride over
the location.
• Make sure to put the wave washer when installing the front seat
inner belt ASSY.
*1
Captions in illustration
*1 Location
SB
(2) Engage the claw and 5 clamps, and install the wiring harness of
the front seat inner belt ASSY LH.
(3) Install the rubber band of the separate type front seat backrest
cover LH.
2. Installation of the front seat inner belt ASSY RH (passenger's side)
(1) Install the front seat inner belt ASSY RH with the nut and the
washer.
Standard value:T=42N·m {428kgf·cm} {31.0ft·lbf}
CAUTION:
• Be careful not to allow the front seat inner belt ASSY RH ride over
the location.
• Make sure to put the wave washer when installing the front seat
inner belt ASSY.
Captions in illustration
*1 *1 Location
(2) Engage the claw and the clamp, and install the wiring harness of
the front seat inner belt ASSY RH.
3. Installation of the front seat cushion shield INN LH (driver's side) (Refer to SE - 25)
4. Installation of the front seat ASSY LH (Refer to SE - 25)
5. Inspection of airbag warning light (Refer to RS - 53)
SB–24 Seat belt - Front seat inner belt ASSY
Unit inspection
1. Inspection of the front seat inner belt ASSY RH
C (1) Measure the resistance according to the following chart.
Resistance
Inspection terminals Inspection conditions Standard value
Tongue plate not inserted to the buckle Less than 1 Ω
1-2
Tongue plate inserted to the buckle Less than 10 kΩ
Captions in illustration
Connector not connected
*a
(Front seat inner belt ASSY RH)
cardiagn.com
SB
Seat belt - Front seat outer belt ASSY
SB–25
Exploded view
Tether clip
x3
cardiagn.com
Separate type rear seat
cushion ASSY RH
30 {306, 22.1}
30 {306, 22.1} x2
30 {306, 22.1}
Removal
WARNING:
The following service operations include the works which may affect the SRS airbag system. Before starting work, always be sure to con-
firm the precautions related to the SRS airbag system. (Refer to RS - 5)
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Disconnection of the battery ground terminal
WARNING:
The air bag and pretensioner system are fitted with a backup power supply. If you start the work within 60 seconds after disconnect-
ing the battery ground terminal, the air bag may be activated. (Refer to IN - 6)
CAUTION:
To avoid damage to the molding, be sure to fully open the door glasses on both driver's and passenger's sides.
2. Removal of separate type rear seat cushion ASSY (Refer to SE - 31)
3. Removal of the front door scuff plate RH (Refer to IT - 48)
4. Removal of the front door opening trim weather strip RH
(1) Remove the front door opening trim weather strip RH to the extent that the quarter lower trim RH and the center pillar
garnish RH can be removed.
5. Removal of quarter lower trim RH (Refer to IT - 49)
6. Removal of quarter trim lid RH (Refer to IT - 49)
cardiagn.com
7. Removal of the rear window side garnish RH (Refer to IT - 50)
8. Removal of the quarter rear trim garnish FR RH (Refer to IT - 51)
9. Disconnection of front seat outer belt ASSY RH
(1) Turn over the floor anchor cover.
Captions in illustration
*1 Floor anchor cover
(2) Loosen the bolt and disconnect the floor anchor part of the front
seat outer belt ASSY RH.
SB
SB-00704
Seat belt - Front seat outer belt ASSY
SB–27
(2) Using the fine flat tip screwdriver wrapped with protective tape, pull
off the lock of the pretensioner connector to unlock it.
Captions in illustration
*1 Protective tape
*2 Pretensioner connector
*a Unlock it.
(3) Using the fine flat tip screwdriver wrapped with protective tape, dis-
connect the pretensioner connector.
SB-00705
(4) Remove 2 bolts and the guide, and remove the front seat outer
belt ASSY RH.
cardiagn.com
SB-00706
Installation
WARNING: SB
The following service operations include the works which may affect the SRS airbag system. Before starting work, always be sure to con-
firm the precautions related to the SRS airbag system. (Refer to RS - 5)
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Installation of the front seat outer belt ASSY RH
C (1) Check of the inclination angle for activating the ELR locking opera-
E
tion
(a)Slowly move the retractor from the installation position, and
D check that the belt is not locked when the angle is within 12° in
all directions, and that it is always locked when the angle is 27°
or larger in all directions.
Captions in illustration
*a Unlocked
*b Locked
*c 27°
CAUTION:
Do not disassemble the retractor.
SB–28 Seat belt - Front seat outer belt ASSY
(2) Insert the guide, and install the retractor part of the front seat outer
# belt ASSY RH with 2 bolts.
Standard value:Bolt A
T=7.5N·m {77kgf·cm} {5.5ft·lbf}
Bolt B
T=30N·m {306kgf·cm} {22.1ft·lbf}
$ SB-00707
(3) Connect the pretensioner connector to the front seat outer belt
ASSY RH.
Captions in illustration
*a Push and lock it.
cardiagn.com
outer belt ASSY RH.
Standard value:T=30N·m {306kgf·cm} {22.1ft·lbf}
C
SB-00708
Exploded view
cardiagn.com
30 {306, 22.1}
SB
Removal
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Removal of separate type rear seat cushion ASSY (Refer to SE - 31)
2. Removal of the rear seat belt ASSY inner
(1) Remove the bolt and remove the rear seat belt ASSY inner.
SB–30 Seat belt - Rear seat inner belt ASSY
Installation
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Installation of the rear seat belt ASSY inner
(1) Install the rear seat belt ASSY inner RH with the bolt in the direc-
tion shown in the figure.
Standard value:T=30N·m {306kgf·cm} {22.1ft·lbf}
cardiagn.com
SB
Seat belt - Rear seat outer belt ASSY
SB–31
Exploded view
Tether clip
x3
30 {306, 22.1}
cardiagn.com
13 {133, 9.6}
30 {306, 22.1}
30 {306, 22.1}
Removal
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Removal of separate type rear seat cushion ASSY (Refer to SE - 31)
2. Removal of the front door scuff plate RH (Refer to IT - 48)
3. Removal of the front door opening trim weather strip RH
(1) Remove the front door opening trim weather strip RH to the extent that the quarter lower trim RH can be removed.
SB–32 Seat belt - Rear seat outer belt ASSY
cardiagn.com
#
Installation
NOTE:
SB The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Installation of the rear seat 3-point type belt ASSY OUT RH
(1) Check of the inclination angle for activating the ELR locking opera-
C tion
Captions in illustration
*a Unlocked
*b Locked
D *c 27°
(4) Install the floor anchor part of the rear seat belt ASSY OUT RH
with the bolt.
Standard value:T=30N·m {306kgf·cm} {22.1ft·lbf}
CAUTION:
• Pay attention to the direction to install the floor anchor part.
• Be careful not to allow the floor anchor part ride over the location.
• Be careful not to twist the rear seat belt ASSY OUT RH.
Captions in illustration
*1 Location
cardiagn.com
SB
SB–34 Seat belt - Child seat restraining device (ISO-FIX)
Exploded view
x3
x2
33 {336, 24.3}
cardiagn.com
13 {133, 9.6}
13 {133, 9.6}
x3 Tether clip
x2
7.5 {77, 5.5}
cardiagn.com
x2
SB
x2
x2
Front door scuff plate RH
Removal
1. Removal of separate type rear seat cushion ASSY (Refer to SE - 31)
2. Removal of the separate type rear seat cushion ASSY LH
NOTE:
Remove the part in the same manner as RH side.
3. Removal of the bench type rear seat backrest ASSY (Refer to SE - 31)
4. Removal of the front door scuff plate RH (Refer to IT - 48)
5. Removal of front door scuff plate LH
NOTE:
Remove the part in the same manner as RH side.
6. Removal of the front door opening trim weather strip RH
(1) Remove the front door opening trim weather strip RH to the extent that the luggage compartment trim side cover RH can
be removed.
7. Removal of front door opening trim weather strip LH
NOTE:
Remove the part in the same manner as RH side.
8. Removal of quarter lower trim RH (Refer to IT - 49)
9. Removal of quarter lower trim LH
cardiagn.com
NOTE:
Remove the part in the same manner as RH side.
10. Removal of quarter trim lid RH (Refer to IT - 49)
11. Removal of quarter trim lid LH
NOTE:
Remove the part in the same manner as RH side.
12. Removal of the rear window side garnish RH (Refer to IT - 50)
13. Removal of the rear window side garnish LH
NOTE:
SB Remove the part in the same manner as RH side.
14. Removal of package tray trim panel ASSY (Refer to DL - 111)
15. Removal of the child restraint seat tether anchor bracket
(1) Remove the bolt.
(2) Remove the guide and remove the child restraint seat tether
anchor bracket.
NOTE:
Remove both parts using the same procedures.
Installation
1. Installation of the child restraint seat tether anchor bracket
(1) Insert the guide and temporally install the child restraint seat tether anchor bracket.
(2) Install the child restraint seat tether anchor bracket with the bolt.
Standard value:T=25N·m {255kgf·cm} {18.4ft·lbf}
NOTE:
Install both parts using the same procedures.
2. Installation of package tray trim panel ASSY (Refer to DL - 112)
3. Installation of the rear window side garnish RH (Refer to IT - 57)
Seat belt - Child seat restraining device (ISO-FIX)
SB–37
cardiagn.com
14. Installation of separate type rear seat cushion ASSY (Refer to SE - 39)
15. Installation of the separate type rear seat cushion ASSY LH
SB
SB–38 Seat belt - Child seat fixing device (ISO-FIX)
Exploded view
x3
cardiagn.com
Trunk trim cover INN RH
x2
SB 13 {133, 9.6}
33 {336, 24.3} x3
25 {255, 18.4}
Quarter lower trim RH
x2
Front door scuff plate RH
Removal
1. Precautions for handling the device
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
2. Removal of separate type rear seat cushion ASSY (Refer to SE - 31)
3. Removal of the bench type rear seat backrest ASSY (Refer to SE - 31)
4. Removal of the child restraint seat anchor bracket RH
(1) Remove 2 bolts and remove the child restraint seat anchor bracket
RH.
cardiagn.com
(1) Remove the front door opening trim weather strip RH to the extent that the quarter lower trim RH can be removed.
7. Removal of quarter lower trim RH (Refer to IT - 49)
8. Removal of the rear seat hinge RH
(1) Remove 3 bolts and remove the rear seat hinge RH.
SB
Installation
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Installation of the rear seat hinge RH
(1) Install the rear seat hinge RH with 3 bolts.
Standard value:T=33N·m {337kgf·cm} {24.3ft·lbf}
2. Installation of the quarter lower trim RH (Refer to IT - 58)
3. Installation of the front door opening trim weather strip RH (Refer to IT - 58)
4. Installation of the front door scuff plate RH (Refer to IT - 58)
5. Installation of the child restraint seat anchor bracket RH
(1) Install the child restraint seat anchor bracket RH with 2 bolts.
Standard value:T=25N·m {255kgf·cm} {18.4ft·lbf}
6. Installation of the bench type rear seat backrest ASSY (Refer to SE - 39)
7. Installation of separate type rear seat cushion ASSY (Refer to SE - 39)
SB–40 Seat belt - Child seat fixing device (ISO-FIX)
cardiagn.com
SB