Professional Documents
Culture Documents
Thickness CBR
Layer Thickness 350 Layer 1 189 28.1
No Of Blows 15 Layer 2 131 17.8
Layer 3 100 7.4
Thickness/Blows 23.3 Layer 4 140 3.4
Layer 5 360 0.6
Log10 (Thickness/Blows) 1.367977
2.48-1.057 Log10 (Thickness/Blows) 1.034049
DCP CBR % 10.8 A 574.597736
B 342.040839
C 194.869516
D 210.517243
E 303.63576
Sum(A to E) 1625.66109
Total thickness 920
Equivalent CBR 5.51729944
Proctor Compaction 1.770
1.768
Mould Weight 3438 1.766
Mould Volume 943 1.764
1 2 3 4 5 1.762
1.760
Moisture content, %
LL PL Determination of Liquid Limit
Blows 1 2 3 4 5 6 7
60.00
45.00
20 30 40 50 60 70
25
No. of blows
CBR FORCE- 30KN CBR FORCE - 50KN
A -0.0242779 1 A -0.042737 92
B 0.119292 B 0.214238
C -7.99035E-06 C -3.83471E-06
D -1.35582E-08 D -3.94867E-08
F 0.10 F 19.60
CBR 38
CBR over 12% Fines 75 GM,GC,SM,SC,ML,MH,CL,CH
Sieve analysis
Before Washed 9,594.0
After Washed 9,377.0 Fine Agg
Sub base Shoulder Coarse Agg 2 3 ABC
Cumulative % Passing
pan 9.4 10.8 0 10 0 10
Total 10303 Mass of fraction passing on 5mm siev 3279 5 25 5 25 SIEVE ANALYSIS
5 12
100.0
Mass of sub division fraction sieved ( 2849
Washout 80.0
40.0 50.0 0
50.0 100
20.0 37.5 100 …
100 100 37.5 .
0 8 5 4 1
0.0
91 100 0.01 20.0 0 0.1 1 10 100
85 100 -20.0
20.0 100
75 100 5.0 100
60 79 5.00 0
Sieve Size (mm)
1.18 0
Grading spec limit
12 40 1.18 100
0 10 ### 100
### 0
### 0
### 100
Sieve analysis
Before Washed 2,842.0
After Washed 2,565.7 Fine Agg
Cumulative % Passing
Passing Sub base Shoulder Coarse Agg 2 3 ABC
Washout
Total 2,564.70 9.7%
LIMITS
50.0 0
50.0 100
37.5 100
100 100 37.5 0
91 100 20.0 0
75 100 20.0 100
55 90 5.0 100
35 59 5.00 0
1.18 0
8 30 1.18 100
0 10 ### 100
### 0
### 0
### 100
1 2
TRIAL NO 1 2 3
SAND IN CONE WITH BASE PLATE
Wt. of Apparatus + Sand before Pouring (g) 15000 15000 15000
Wt. of Apparatus + Sand after Pouring (g) 13845 13849 13848
Wt. of Sand in Cone (g) 1155 1151 1152
Average Wt. of Sand in Cone (g) 1153
DENSITY OF SAND USING MOULD
Wt. of Apparatus + Sand before Pouring (g) 15000 15000 15000
Wt. of Apparatus + Sand after Pouring (g) 9610 9603 9601
Wt. of Sand to fill Mould, Base Plate & Cone (g) 5390 5397 5399
Wt. of Sand in Mould (g) 4237 4244 4246
Volume of Mould (cm3) 3089
Bulk Density (g/cm3) 1.372 1.374 1.375
Average Density (g/cm3) 1.373
Sample No 1
LOCATION
SIDE
HEIGHT OF CORE mm 53
OFFSET m 1.5
MASS OF CORE SPECIMEN IN AIR mm 1014.0
MASS OF CORE SPECIMEN IN WATER g 603.3
MASS OF S.S.D.CORE SPECIMEN IN AIR g 1034.8
BULK S.G. OF COMPACTED MIX g/cm3 2.350
BULK S.G. OF MIX IN THE LABORATORY g/cm3 2.391
SPECIFIED LIMIT % 97.0
98.3
% Compaction Achieved
Approved