Professional Documents
Culture Documents
net/publication/336813384
CITATIONS READS
0 2,316
1 author:
SEE PROFILE
Some of the authors of this publication are also working on these related projects:
The Residual Lateral Earth Pressure on Retaining Wall due to Compaction View project
All content following this page was uploaded by Moamen E. Abd El Raouf on 25 October 2019.
L=2(S+e)
B=S+2e
3- Determine the pile working load
a) For concentrically loaded pile cap: حمل رأسى متمركز على الهامة
1.1Pw(colu mn)
Pw(pile)
No.of pile
b) For eccentrically loaded pile cap: حمل رأسى غير متمركز على الهامة
- V My. X Mx. y
Pv
N x2 y2
4-Determine the ultimate pile load
Pu (pile) =1.5 Pw (pile)
5-Design of flexure
The critical section of moment is taken at the face of column as shown in
figure (3-4).
Mu1 = Pu1xa+Pu4 x a
Mu2 = Pu1xb+Pu2 x b + Pu3xb
Where:
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
يتم تجاهل رد فعل الخازوق عندما يقع الخازوق بالكامل داخل القطاع الحرج للقص-2
فى حالة وجود جزء من الخازوق خارج القطاع الحرج للقص يتم احتساب هذا الجزء فقط من-3
)3-5( الخازوق عند حساب قوى القص وذلك كنسبة من مساحة الخازوق كما هو موضح بشكل
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
Qsh1 - 1
qsh1 - 1
B.d
Where:
fcu =the concrete compressive strength.
γc =1.5
د.م /مؤمن السيد عبد الرءوف -هندسة األزهر
)(D/2 X
Fr
D
فى حالة ما يكون القطاع الحرج يقع على مسافة أكبر من المسافة بين وجه العمود ومركز الخازوق
)(X D/2
Fr
D
فى حالة ما يكون القطاع الحرج يقع على مسافة أقل من المسافة بين وجه العمود ومركز الخازوق
أى أن معامل التخفيض = طول الجزء المؤثر فى القص من القطر /القطر الكلى للخازوق
Where:
Fr = reduction factor
D=pile diameter
المسافة بين محور الخازوق والقطاع الحرج =X
Where:
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
Mu 2 - 2
As2-2= →=As2/m = As2-2/L
j.d.fy
Check: As2-2 > As min= (0.6/fy)x L x d
9-Details of reinforcement
يكون تسليح الهامة فى هذه الطريقة من التصميم مماثال لتسليح القواعدالمسلحة (سواء منفصلة أو
.)3-8( مشتركة أو قاعدة جار) وذلك كماهو موضح بشكل
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
Problem (3-2)
Design and give complete reinforcement detailing for a pile cap, knowing that
column dimension = 0.6×0. 6 m, column working load = 2000 kN
Pile diameter = 0.4 m, Pile working load =600 KN, fcu = 30 N/mm² , fy = 360
N/mm².
Solution
1.15 Pw
No. piles = 1.15x2000/600=3.83, take 4 piles
Qall
Assume S= 3D (pile diameter) = 3x0.4= 1.2 m
e=1.25xD=1.25x0.4=0.5m→ L= B= 1.2+2x0.5=2.2m
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
1.1Pw(colu mn)
Pw(pile) 1.1x2000/4 550kN
N.o.of pile
Pu (pile)=1.5x550=825kN
Mu1-1=Mu2-2 =Mu
Mu= No. of piles xPu xa , a=(1.2-0.6)/2= 0.3m
Mu=2x825x0.3=495 kN.m
Check of shear:
د.م /مؤمن السيد عبد الرءوف -هندسة األزهر
حيث أن القطاع الحرج للقص يقع على بعد 35سم من وش العمود فعلى ذلك يمكن حساب القص
كالتالى :
qcu =0.16√(30/1.5)=0.715N/mm²
qsh˂qcu ok
Check of punching:
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
U=[(0.6+0.7)+(0.6+0.7)]x2=5.2m=5200mm
qp=2081x10³/(5200x700)=0.57N/mm²
The allowable punching stress (qcup) is giving as the least value of the
following:
3- qcup=0.8(0.2+(4x0.7/2.6)√(30/1.5)=4.57N/mm²
As=495x106/(0.826x700x360)=2378.06 mm²/2.2m
ملحوظة :
عند تصميم هامة الخوازيق كقاعدة مشتركة البد من توزيع الخوازيق بحيث تنطبق نقطة تأثير محصلة
أحمال األعمدة مع مركز ثقل الخوازيق ثم يستكمل الحل بالطريقة المعتادة.
b) Finite element method analysis of pile cap
هندسة األزهر- مؤمن السيد عبد الرءوف/م.د
In some cases, the manual methods to analysis a pile cap is not available or
not accurate, the internal forces of pile cap can be determined by using a
computer program like sap. In this method the pile cap is modeled as a shell
element and pile modeled as a spring element as shown in figure (3-9). The
pile spring constant (Kpile) can be calculated as following: