Professional Documents
Culture Documents
Calculate the
pressure at the wellbore and at a location 500 feet away from the well after 5 days, and 10 days of production.
The drainage boundary of the well is located 1000 feet away. Other rock and fluid propertiesof the reservoir
are as follows:
-0.9649285714286 x= -0.4824642857143
-0.235 Ei= -0.585
Pi(psi)= 2500
K(md)= 300 q1(STB/dia)= 300 t1=
Ct(psi^-1)= 6.00E-06
B(RB/STB)= 1.2 q2(STB/dia)= 500 t2=
rw(ft)= 0.5
H(ft)= 15 Tp=
Porosidad= 0.24
Viscocidad(cp)= 4.2
r(ft)= 1500
x= -0.0511920000000
Ei= -2.449
240 h
600 h
840 h
x= -0.0716688000000
Ei= -2.138
A reservoir at initial pressure of 2500 psia has two wells (Well A and Well B) on production for 35 days from initial production.
Well A produced at a constant rate of 500 STB/D and is located 750 feet from an observation well. Well B produced at a
constant rate of 300 STB/D and is located 1000 feet from the same observation well. If the reservoir is infinite in size, calculat
the total pressure drop measured at the observation well at the end of 35 days. This reservoir has the same rock and fluid
properties as the reservoir in previous case.
qi(psi)= 2500
qA(STB/dia)= 500
qB(STB/dia)= 300
t(dias)= 840 x= -0.0127980000000 x=
rAO(ft)= 750 Ei= -3.779 Ei=
rBO(ft)= 1000
B(RB/STB)= 1.2
Viscocidad(cp)= 4.2
K(md)= 300 ΔP(psi)= 225.7426528 psi
H(ft)= 15
Ct(psi^-1)= 6E-06
Porosidad= 0.24
5 days from initial production.
ell. Well B produced at a
ervoir is infinite in size, calculate
as the same rock and fluid
-0.0227520000000
-3.218
Asume that the well in case 2, is 1500 feet from a sealing fault. Calculate the total pressure drop at the
wellbore.
qi(psi)= 2500
qA(STB/dia)= 500
qB(STB/dia)= 300 x1= -0.204768 x2=
t(dias)= 35 Ei= -1.202 Ei=
rAO(ft)= 750
rBO(ft)= 1000
B(RB/STB)= 1.2
scocidad(cp)= 4.2 436.666311
K(md)= 300 28.5133632
H(ft)= 15 285.789767
Ct(psi^-1)= 6E-06 14.7232064
Porosidad= 0.24
L(ft)= 1500 ΔP(psi)= 765.692648
-0.2866752
-0.931
Three exploration wells have been drilled into a newly discovered oil reservoir. Well B is 1400 feet from well A,
Well C is 2200 ft from A and Well C is 3000 ft from B.
Well A is an observation well (it has a pressure gauge in the hole to measure the pressure response due to
production from wells B and C, but is not itself used for production). Well C begins producing at 200 STB/D at
time=0. Well B begins producing at 100 STB/D 48 hours later
esponse due to
ng at 200 STB/D at