1. The document provides troubleshooting steps for an "INV V-phase IGBT Error" occurring in a drive system.
2. It involves checking cable connections to the INV, GDC, and transformer, as well as inspecting the V-phase IGBT directly by testing resistances between terminals.
3. If the issue persists after checking connections and IGBT, replacing the INV and GDC circuit boards is recommended.
1. The document provides troubleshooting steps for an "INV V-phase IGBT Error" occurring in a drive system.
2. It involves checking cable connections to the INV, GDC, and transformer, as well as inspecting the V-phase IGBT directly by testing resistances between terminals.
3. If the issue persists after checking connections and IGBT, replacing the INV and GDC circuit boards is recommended.
1. The document provides troubleshooting steps for an "INV V-phase IGBT Error" occurring in a drive system.
2. It involves checking cable connections to the INV, GDC, and transformer, as well as inspecting the V-phase IGBT directly by testing resistances between terminals.
3. If the issue persists after checking connections and IGBT, replacing the INV and GDC circuit boards is recommended.
1. Check the VG connector status of DPC-300(INV) PCB with power OFF. When V-phase +IGBT and -IGBT are turned on simultaneously, or when IGBT driving power has failed or INV output(U, V, W) is short. 2. Verify that the optical cable is well connected to stack section such as U+,U-,V+,V-,W+,W- , respectively. [Diagram] 3. Check the VA, GX, GAI, and GCI connectors in DPP-300(GDC) PCB. 4. Verify if GAI and GBI cable are well connected to FG PCB of V Stack GX3 GP1 U-phase IGBT. DPP-300 GX5 AC 29V
GAI7 5. Check the U-phase power(Verify if the voltage is AC29V between
GET-E18 GAI4 U-phase stack GX3 to 5 in DPP-300 PCB, and AC29V between U GCI7 6 7 GX1 IM V GCI4 GX4 AC 29V GX1 and 4(If power is not correct, replace the transformer. Yet, in GET-E18 W GAI5 6 7 permissible voltage dropping range.) GAI1 6. Verify if HCT cable is well connected to HCT(Verify if U-phase cable is GCI5 GCI1 connected to U-phase HCT and V-phase and W-phase in the same way ). VA1 VA5 INV+ INV- 7. Check the HCT’s direction(Normally, HCT is directed downward to CP 광케이블 Optical Cable VBN-3 floor.) (Refer to TCD30.) VG4 VG13 U+ U- V+ V- W+ W- VBN-7 OPT1 8. Inspect IGBT. VBN-11 DPC-300 9. Replace DPP-300(GDC) PCB. 10. Replace DPC-300(INV) PCB. [How to inspect IGBT] Be sure to open the resistance of FG PCB attached to IGBT before inspection.
Condition + - Analog Tester Digital Tester
C1-C2E1 C2E1 G ∞ ∞ Short G C2E1 ∞ ∞ G-C2E1 C2E1 C1 ∞ Around 10k Ω Short C1 C2E1 10 Ω or less ∞ C2E1-E2 E2 G ∞ ∞ Short G E2 ∞ ∞ G-E2 E2 C2E1 ∞ Around 10k Ω Short C2E1 E2 10 Ω or less ∞