Professional Documents
Culture Documents
FEDERAL HOUSING
BILL OF QUANTITIES
SECTION DESCRIPTION
A SANITARY FIXTURES & FITTINGS (SUPPLY & FIXING CHARGES)
B WATER SUPPLY
C SOIL, WASTE, VENT, ANTISYPHONAGE PIPES & FITTINGS
D RAIN WATER PIPES & FITTINGS
2 Supply and fixing approved quality of table top white vitreous china wash basins
(BS:3402) comprising of the following for complete installation. The fixture shall
conform to BS:5506-3
2.1 Size as mentioned in technical specifications Rectangular top counter wash basin (1
No.)
2.2 32mm dia. CP waste pop up drain (1 No.)
2.3 32mm dia.CP bottle trap with extension piece, CP wall flange complete. (1 Set)
2.4 15mm dia. CP heavy angle, stop cock with wall flanges (2 No.) (hot and cold)
2.5 15mm dia. CP Single lever basin mixer for hot and cold (1 No.)
2.6 Making necessary inlet/outlet connection all complete.
3 Supply and fixing for stainless steel sink of size as per shared technical specifications
(19 gauge) single bowl without drain board of Nirali make or equivalent including
40mm dia. Waste coupling, CP bottle trap, waste flexible pipe upto nahani trap and
making inlet/outlet connections and shall be capable for holt and cold water to used
at the same time all complete as per specifications and directions of the Engineer-in-
charge.
3.1 32mm dia.CP bottle trap with extension piece, CP wall flange complete. (1 Set)
3.2 15mm dia. CP heavy Single Lever Sink Mixer with Swinging Spout wall Mounted
4 Supply and fixing for fixing in position concealed type single lever operated Hot &
Cold bath mixture divertor with shower arm, shower head, bucket filler for
complete installation.
5 Supply and fixing for fixing instant geyser (2 KW Rating) with angle stop cock, CP
connector, PRV, NRV all complete.
5.1 15mm dia. CP heavy angle, stop cock with wall flanges (2 No.) (hot and cold)
5.2 15mm dia. CP heavy inlet connection flexible Stainless Steel pipe (2 No.)
6 Supply and fixing for fixing Auaguard unit with all inlet/outlet with connections all
complete. (for Kitchen)
6.1 15mm dia. CP heavy angle, stop cock with wall flanges (1 No.)
7 Supply and fixing for fixing 20mm dia. x 600mm long C.P. stainless steel towel rods
fixed to wooden plugs with CP screws,brackets,all complete.
8 Supply and fixing for fixing off white vitreous china recessed type soap dish
including making the necessary cut-outs for recessing, grouting the soap dish complete
as directed
9 Supply and Fixing heavy Glass bottle along with Dispenser Holder
10 Supply and fixing for fixing towel rings of stainless steel napkin ring 150mm wide
fixed near wash basin at 42" above floor level.
11 Supply and fixing for CP approved quality angle stop cock for washing machine in
service area and aquaguard in kitchen.
12 Supply and fixing approved quality Stainless Steel Paper Holder along with SS Lid
Supply and fixing Stainless Steel electropolished shower drain channel long with
following accessories, all the accessories and drain shall be quality monitored in
13 accordance with EN 1253-3
2 Providing and Fixing heavy heavy class PPR-3 (PN-16) PIPES (As per DIN:8077 and
DIN:8078) including cutting the pipes to correct length providing and fixing with M.S.
hot dipped galvanized brackets and U clamps alongwith nuts, bolts and washers all
complete with testing, including providing and fixing with all types of PPR-3 fusion
welded fittings (As per DIN:16962 Part 5 to Part 10 )all complete. (Rate must be
inclusive of fittings). (For cold(domestic) water supply internal conceal pipes)
3 Providing and Fixing heavy heavy class PPR-3 (PN-16) PIPES (As per DIN:8077 and
DIN:8078) including cutting the pipes to correct length providing and fixing with M.S.
hot dipped galvanized brackets and U clamps alongwith nuts, bolts and washers all
complete with testing, including providing and fixing with all types of PPR-3 fusion
welded fittings (As per DIN:16962 Part 5 to Part 10 ) all complete. (Rate must be
inclusive of fittings). (For hot water supply internal conceal pipes)
4 Supply and Fixing Bronze gate valves PN-20 which shall be compatible to the PP-R
pipes on the branch pipe line for all the water supply system as shown in the drawings
5 Providing and fixing ball cock heavy duty with copper float all complete.
5.1 40mm dia.
6 Providing and fixing brass screwed/flanged type mosquito proof grating for under
ground suction tank, over flow and vent of the following diameters.
6.1 25mm dia
7 Providing and fixing C.I. Strainer 'Y' type with matching screwed type flanges.
7.1 65mm dia
8 Providing and fixing F.R.P water tank covers with lock and patti arrangement frame
including fixing the same complete as per detailed drawings
8.1 600mm dia. (Load Bearing Capacity : 2.5 Tones) (Over head tank)
9 Providing and fixing Capstan make water meter including providing and fixing
matching Control Valve, strainer, non-return valve, complete including constructing
suitable brick masonry chamber 230mm thick 1:3 cement mortar with plaster inside,
outside in cement mortar 1:3 to house water meter, strainer and valves and provide
125 Kgs. cast iron frame and cover for the chamber, with locking arrangement all
complete as per direction of the Engineer-in-charge. (Excluding Excavation) Valve
chamber size 900 x 600 x 600mm)
10 Providing and fixing 25mm dia. Automatic (RB) air release valve including providing
and fixing cut off & drain valve, making necessary inlet/outlet connection and fixing
with M.S. Brackets complete.
11 Charges for making connection to the existing water supply main system of local
Municipal Corporation including getting all necessary permissions & approvals
from them all complete.
12 Providing and fixing Pressure Reducing Valves (Full Bore Series) with strainer
arrangement as approved including fixing the same of the following diameters.
12.1 40mm dia
13 Providing and fixing Water Hammer Arrestor in plumbing shaft at the lower most level
along with required necessary fittings.
13.1 25mm dia.
1 Providing and fixing UPVC PN-6 pipes and clean outs for soil and waste line
from water-closet and floor trap to plumbing shaft and from shaft to nearest
manhole - all in accordace to the drawing (slope mentioned in drawing) to
correct grade, length and alignment including jointing with solvent cement,
testing, fixing to G.I. brackets/clamps complete as per specifications and
directions of the Engineer-in-charge, including all kinds of fittings.
2 Providing and fixing cast iron pipe along with necessary fitting and accessories
confirms to FG-200 grade as specified in IS 210-2002/ISO-185 having a specific weight
of 7.15kg/cu.dm to correct grade, length and alignment including jointing with solvent
lead cement, testing, fixing to G.I. brackets/clamps complete as per specifications
and directions of the Engineer-in-charge.
4 Providing and fixing UPVC vent cowls including fixing the same with ring fittings
joint complete as per specifications and directions of the Engineer-in-charge.
5 Providing and fixing 75mm dia uPVC floor gully trap drain conform to ASME stds
A112.6.3 (Heavy duty) or equivalent insititution complete with Trapped Floor Gully and
all the necessary accessories. Trapped Floor Gully.
2 Providing and fixing cast iron dome shaped grating including making proper
recessment, grouting with cement mortar 1:1 Anti corrosive painting as approval all
complete as per specifications for the following pipe size.
2.1 110mm dia
3 Providing and fixing lead sheet flashing sheet of size 300mm x 300mm to suit the
following dia pipes/rain water outlet using lead sheets weighing not less than 27.5
Kg.per sq.m.including moulding to proper shape and grade including cutting of
R.C.C. roof slab or wall as required and providing and fixing with cement mortar 1:2
with water proof compound etc. all complete as per specifications and directions of
the Engineer-in-charge.
4 Providing and fixing FRP heavy quality gratings (5-10mm thick) for floor drains
including making necessary recessment grouting with neat cement all complete to
the satisfaction and direction of the of the Engineer-in-charge.
4.2 100mm round/square
5 Providing and fixing 75mm dia uPVC floor gully trap drain conform to ASME stds
A112.6.3 (Heavy duty) or equivalent insititution complete with P-smell trap and all the
necessary accessories. Trapped Floor Gully
TOTAL CARRIED OVER TO SUMMARY PAGE
SANITARY BOQ (QUANITIY FOR ONLY ONE BUILDING)
FEDERAL HOUSING
BILL OF QUANTITIES
DESCRIPTION AMOUNT
TOTAL
Qty Unit Rate (INR) Amount (INR)
Material Labour Total Material Labour Total
100.00 Nos.
100.00 Nos.
40.00 Nos.
100.00 Nos
140.00 Nos.
40.00 Nos
100.00 Nos.
100.00 Nos.
100.00 Nos.
100.00 Nos.
40.00 Nos.
100.00 Nos.
80.00 Nos.
15.00 RM
200.00 RM
65.00 RM
462.00 RM
231.00 RM
140.00 RM
1560.00 RM
370.00 RM
300.00 RM
430.00 RM
140.00 Nos.
14.00 Nos.
72.00 Nos.
8.00 Nos.
1.00 Nos.
3.00 Nos
4.00 Nos.
3.00 Nos.
1.00 No.
4.00 Nos
RO L.S.
14.00 Nos.
14.00 Nos.
56.00 RM
572.00 RM
980.00 RM
479.00 RM
RO RM
140.00 Nos.
10.00 Nos
14.00 Nos
140.00 Nos
343.00 RM
105.00 RM
8 Nos.
8 Nos.
80.00 Nos.
80.00 Nos