Professional Documents
Culture Documents
So, please look at all the facts while selecting a project. Think…which mechanical software you know or
think what else you can do? If you are not getting any idea, then this article is for you. In this article, I
had presented about 650+Updated Mechanical Engineering Projects Ideas of all Domains along with a
few projects in a detailed way. From here, you can pick any project of your choice.
Below Tabular Column Navigates the detailed explanation of Mechanical Engineering Projects along with
their Ideas.
Effects Of Minimum Quantity Lubrication On Turning Aisi9310 using Vegetable oil Cutting Fluid
What is Blue Brain and how a man thinks even after his death?
Apart from the above, you can visit the articles by just clicking on it in the below tabular column:
4.(100+Updated) Thermal Engineering Projects List for Mechanical and Diploma Students
11.An updated list of CNC Vertical Milling Machine Projects for Mechanical Students
15.280+Updated list of Mini Projects for Mechanical Engineering 3rd Year Students
21.Updated Projects list of Tool, Die, Jigs and Fixtures for Mechanical Engineering students
1.Automatic Speed Control In 4-wheeler by Cruise Control Automatic Speed Control In 4-wheeler by
Cruise Control: Everyday the media brings us the horrible news about road accidents. The concept of
assisting the driver in longitudinal vehicle control or driving from one place to another without taking
any rest makes an impact on everyone’s life. So, avoiding collisions has been a major focal point of
research in many automobile companies and research organizations. Therefore in this article, I am going
to explain about the Automatic Speed Control In 4-wheeler by Cruise Control in a detailed way.
Modern cruise control (also known as a speed stat) was invented by mechanical engineer Ralph Teetor in
1945.The idea of driver assistance was started with the ‘cruise control devices’ first appeared in the
1970s in the USA. When switched the cruise control ON, the device takes up the task by accelerating to
maintain a constant speed.
Generally, the usage of cruise control can be adopted in highways where separate tracks will be there
and you can move with your desired speed. But it could not consider the other vehicles on the road.
When the driver drives the vehicle on the road, he should have to accelerate or decelerate whenever
required. but at Speed Limit Zones, the vehicle has to move without varying in speed and this can be
done using Cruise Control.
Cruise Control is useful for long drives across highways and sparsely populated roads by reducing fatigue
to the driver. This usually results in better fuel efficiency.
Cruise control is a system that automatically controls the speed of an automobile.The system takes over
the throttle of the car to maintain a steady speed as set by the driver.This system thereby improves
driver comfort in steady traffic conditions also. In congested traffic conditions, where speeds may vary
widely these systems are no longer effective.
The driver must bring the vehicle up to speed manually and uses a button to set the cruise control to the
current speed.
The cruise control takes its speed signal from a rotating driveshaft, cable of the speedometer, wheel
speed sensor from the engine’s Rpm or from internal speed pulses produced electronically by the
vehicle.
Most systems do not allow the use of the cruise control below a certain speed (normally around 25
mph).
Nissan Qashqai 1.6 dCi Tekna 5dr [Start Stop] diesel hatchback,e.t.c.
2.Development of CNC Program for End Shield by Unigraphics Software: Mechanical Engineering Projects
End shield is a part of the transmission system which is used to cover the motors in most of the trains. As
motors play a vital role in the transmission of power, this end shield is used to act as a cover on it so that
no unevenness takes place in the surroundings. In this Article, I am going to explain about the
Development of CNC Program for End Shield by Unigraphics Software in a detailed way.
Development of CNC Program for End Shield by Unigraphics Software-Mechanical Engineering Projects
CAD/CAM system has a natural break at the point where it produces or delivers a Generic form of
Numerical Control output called CL-file (Cutter Location File).
This generic intermediate output represents the path that the machine cutter will take while machining
the part. It does not reflect and is not optimized for the specific CNC Control which will actually use to
cut the part.
NX-CAM is the latest CAM software, which has important features like 2D, 3D, Surface modeling,
Manufacturing, etc.
The component can be designed using NX_CAD software. Then the sequence of programs such as
modeling the part or component, generating the tool path, selection of tools according to the sequence
of operations and sizes takes place with respects to the program given or allowed.
At last the generated NC part program is verified and sent to the required CNC machine to manufacture
the component.
This project of End shield deals with the development of the NC program using NX-CAM software.
3.Modeling and Manufacturing of Input Shaft using Computer Aided Manufacturing: Mechanical
Engineering Projects
In modern CNC systems, from the beginning to the ending, the component design is highly automated by
means of Computer Aided Design (CAD) and Computer Aided Manufacturing (CAM) programs. In this
article, I am going to publish the project of Modelling and Manufacturing of Input Shaft using Computer
Aided Manufacturing in NX CAD Software in a detailed manner.
Modeling and Manufacturing of Input Shaft using Computer Aided Manufacturing-Mechanical
Engineering Projects
Since any particular component might require the use of a number of different tools like drills, saws, etc.
modern machines often combine multiple tools into a single “cell”.
In other installations, a number of different machines are used with an external controller and human or
robotic operators that move the component from machine to machine.
The programs produce a computer file that is interpreted to extract the commands needed to operate a
particular machine by a post processor and then loaded into the CNC machines for production.
In either case, the series of steps needed to produce any part is highly automated and produces a part
that closely matches the original CAD design.
This project deals with generating NC program using CAM software in NX CAM for input shaft to
manufacture on a modern CNC machine.
Using NX-CAD software 3D model of the input shaft is created and the program is generated using NX-
CAM software.
Power enters the transmission through the input shaft. The input shaft is connected to the engine via the
clutch, such that when the clutch is engaged, power goes straight from the engine to the input shaft of
the transmission and the crankshaft and input shaft rotate at the same speed.
4.Optimization of Manufacturing Process Plan of GIMBAL for Targeted Missiles: Mechanical Engineering
Projects
Process planning is concerned with determining the sequence of individual manufacturing operations
needed to produce a given part or product. In this article, I am going to publish about the project of
optimization of manufacturing process plan of gimbal for targeted missiles in a detailed manner with the
help of Abstract, Explanation, and Aim of the project.
Optimization of Manufacturing Process Planning of GIMBAL-Mechanical Engineering Projects
Process planning translates design information into the process steps and instructions to efficiently and
effectively manufacture products. The resulting operation sequence is documented on a form typically
referred to as a process sheet/method sheet containing a listing of the production operations and
associated machine tools for a work part or assembly. Process planning in manufacturing also refers to
the planning of the use of blanks, spare parts, packaging material, user instructions (manuals), etc.
The sensor platform consists of an outer (azimuth) and inner (elevation) gimbals.
The two gimbals actuator systems are assembled to sensor plate for target missiles.
The purpose of the gimbaled stabilization system is to stabilize the sensor’s line of sight towards a target
by isolating the sensor from the disturbance induced by the operating environment.
Creating holes with high accuracy is a tough task on a lathe mill machine.
To overcome from this problem number of operations and repeated drilling operations should be
reduced.
Repeated drilling operations reduce the positioning of holes and dimensional accuracy of holes.
To reduce the number of operations specified tools must be designed according to the model of gimbal
outer.
The main aim of this project is creating a 3D model using Unigraphics software.
Generating NC program of gimbal using NX-CAM software which is exclusively CAM software used to
generate part program by feeding the geometry of the component and defining the proper tool path and
thus transferring the generated part program to the required CNC machine with the help of DNC lines.
The operator thus executes the program with suitable requirements. The project deals with optimizing
process plan by specifying appropriate tools, developing tools design if demanded.
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
5.Effects Of Minimum Quantity Lubrication On Turning Aisi9310 using Vegetable oil Cutting Fluid:
Mechanical Engineering Projects
In many applications, dry machining is not a practical solution due to significant reductions in tool life
and productivity. In comparison to entirely dry machining, MQL(Minimum Quantity Lubrication) can
reduce machining temperatures considerably and increase tool life. In this article, I am going to publish
about the Effects Of Minimum Quantity Lubrication On Turning Aisi9310 using Vegetable oil Cutting Fluid
in a detailed manner.
Effects Of Minimum Quantity Lubrication On Turning Aisi9310 using Vegetable oil Cutting FluidEffects Of
Minimum Quantity Lubrication On Turning Aisi9310 using Vegetable oil Cutting Fluid-Explanation:
Introduction
Experimental Conditions
RESULTS
CONCLUSIONS.
Introduction to Effects Of Minimum Quantity Lubrication On Turning Aisi9310 using Vegetable oil Cutting
Fluid:
In many applications, dry machining is not a practical solution due to significant reductions in tool life
and productivity.
In comparison to entirely dry machining, MQL can reduce machining temperatures considerably and
increase tool life.
Experimental Conditions:
The experimental investigations were conducted with a view to exploring the role of MQL on the
machinability characteristics of the work material mainly in terms of cutting temperature, chip
formation, tool wear, and surface roughness.
Depth of cut was kept fixed to only 1.0mm, which would adequately serve the present purpose.
Work specimens:
Size ? 100×710 mm
Process parameters:
6. What is Blue Brain and how a man thinks even after his death?-Mechanical Engineering Projects
What is Blue Brain and how a man thinks even after his death: This Blue brain concept makes the mans
idea into the machine even after his death. It means that even after the death of a person, his ideas are
to be incorporated into a machine so as to run with the ideas of a person in an effective manner. In this
article, I am going to publish What is Blue Brain and how a man thinks even after his death in a detailed
manner.
What is Blue Brain and how a man thinks even after his death?-Mechanical Engineering Projects
What is Blue Brain and how a man thinks even after his death?-Mechanical Engineering Projects
Introduction
Functions of Brain
Brain simulation
Hardware&Software Requirements
The human brain is the most valuable creation of God. The man is called intelligent because of his brain
but he can lose his memory when he attains his death i.e when the body damages permanently.
The name of the first virtual brain is the Blue Brain that means a machine that can function like a human
brain.
Is it really possible to create a Human brain? For this, the answer is yes.
Now the IBM was developing a virtual brain known as the Blue Brain.
It can think.
It can response.
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
Material Selection for Unmanned Aerial Vehicles(Drone): An unmanned aerial vehicles (UAV) is
commonly known as a drone and also referred by several other names is an aircraft without a human
pilot. The flight of UAV’s may be controlled either autonomously by onboard computers or by the remote
control of a pilot on the ground or in another vehicle. This post mainly focuses on the Material Selection
for Unmanned Aerial Vehicles (Drone) and is as follows.What is the Material Selection for Unmanned
Aerial Vehicle(Drone)
Introduction
Objective
Major Requirements
Materials used
Material Selection
wood(Balsa)
Carbon fiber
Thermacol
Aluminum Alloys
Steel
Titanium Alloys
CFRP
Uses of UAV’S
Applications
ICAO classified unmanned aircraft into two types under Circular 328 AN/190:
Autonomous aircraft – currently considered unsuitable for regulation due to legal and liability issues
Remotely piloted aircraft – subject to civil regulation under ICAO and under the relevant national
aviation authority.
Historically, UAVs were simple remotely piloted aircraft, but autonomous control is increasingly being
employed.
Unmanned aerial vehicles have mostly found in military and special operations applications, but also are
increasingly finding uses in
Civil applications such as policing, surveillance and firefighting
UAVs are often preferred for missions that are too “dull, dirty or dangerous” for manned aircraft.
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
Computer Controlled Drilling Machine: Current development in the industry has been towards computer
controlled manufacturing to increase the quality and quantity of products. Manual manufacturing of
such items as the circuit board will have a big faulty case and uneven quality. Then I have developed an
automatic print circuit board drilling machine, which is controlled by computer.
The main aim of computer controlled drilling machine is to drill holes on printed circuit boards (PCB) in a
specified area. The program is written in assembly language and a step by step approach is implemented
to control four motors independently. It generally consists of a transformer, PC, MAX232, diodes,
microcontroller, relay, stepper motors, AC motor, drilling machine, limit switches, transistors, etc. Co-
ordinates are given through keyboard of PC by the set of rules and regulations.
The information sent from PC to Microcontroller is passed via MAX232 which converts TIA/EIA-232-F
inputs to 5V TTL/CMOS levels. By this microcontroller commands the stepper motors and AC motor to be
in home position before the work is done.
The entire working depends upon driving of stepper motors in both the directions (clockwise or anti-
clockwise).
The system is programmed to produce the pulses in a sequence at four different outputs (9 5 6 A). These
sequentially programmed outputs energize the motor winding one after the other in a sequence.
The information from the microcontroller is passed to drilling machine via a relay which converts 5V
supply to 12V to rotate the drill. As per the data fed to the machine, it can drill as many holes as in a
specific area.
After completing the task, the computer displays on its monitor that the job is completed. To avoid
friction, the mechanical transmission part of each axis is designed with sliding channels.
The main aim of the project lies in interfacing or in simple words, is to make a mechanical system work,
making use of a personal computer of basic configuration.
This project is carried on keeping in mind, the needs of a small scale industry, which need small sized
components in a few numbers, which by other processes would cost them more.
This project makes use of a printed circuit board that interfaces a drilling machine with a personal
computer. This system is mainly aimed at small scale production of printed circuit boards in small scale
industries.
The system has an advantage of simplicity in operation, moreover, the cost of production comes down
for a small scale sector.
Though the system involves many small electronic parts it is easy to study the working, and in operation,
as we use the simple user-friendly language in programming the software.
The goal here is to design and build a very low-cost, very simple, desktop drilling machine, which is used
for drilling the PCB’s (printed circuit boards).
Drilling the PCB’s manually consumes a lot of time and due to errors by drilling at wrong points, causes
wasting many PCB’s.
All these problems can be avoided by implementing the Computer control concept, thereby this project
work is taken up and a prototype module is constructed for the live demonstration.
Since it is a prototype module, the size of the work or drilling size of the PCB is minimized. Due to the
restriction, the machine cannot drill PCB of more than 12 X 20cm.
The block diagram of a computer controlled drilling machine is shown below which consists of the
following parts.They are Microcontroller,stepper motors,AC motor,limit switches,relay,PC,MAX232 etc.
FUNCTION OF A PROGRAM
A set of encoded information, which provides coordinate values and other instructions to indicate how
the machine tool is moving in relation to a workpiece in order to achieve a specific desired machining
form can be called as a function of a program.
The program should be prepared such that, it should contain all the information for the machining of a
component which is input to the computer controlled drilling machine.
Depending upon the input from the computer, the system provides signals at the correct time and in the
correct sequence to the various drive units of the machine.
The machine tool receives information from the computer and does the operation on the machine. The
program is prepared by listing the coordinate values of the entire tool paths as suited to a machine.
In the case of the drilling machine, the coordinate values to be prepared for 3D for driving three motors
independently.
Two motors are used for moving the platform in X and Y directions and the third motor is used to move
the drill in the Z direction.
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
9.Generating NC Program of Journal Bearing using NX CAM software: Mechanical Engineering Projects
Journal bearings consist of a shaft or journal which rotates freely in a supporting metal sleeve. There are
no rolling elements in these journal bearings. The design and construction of Journal bearings may be
relatively simple, but the theory and operation of these bearings can be complex. In this article, I am
going to publish about the generation of NC Program of Journal Bearing using NX CAM software in a
detailed manner.
Abstract:
Manufacturing technology provides tools that enable the production of all manufactured goods and
services in an effective way.
These master tools of industry magnify the effort in making essential products from the raw material to
the finished goods with high dedication and accuracy so that they can compete with the market needs.
As discussed earlier, A journal bearing is the simplest type of bearing, comprising just a bearing surface
and no rolling elements. Journal bearings, in general, are the least expensive type of bearings.
The Journal bearings are compact and lightweight and they have a high load-carrying capacity.
This project deals with generating NC program using CAM software for Journal bearing to manufacture
on a modern CNC machine.
Using NX-CAD software 3D model of Journal bearing is created and the program is generated using NX-
CAM software.
The generated program is fed into the CNC or DNC machines to carry out the operation in a successful
way.
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
The Mixing and Nodulizing Drum (MND) is a part of Sinter Plant used for mixing the ingredients with
blast furnace fines before feeding the same to the sinter machine. The drum is a cylindrical vessel,
inclined slightly to the horizontal, which is rotated about its axis. As the drum rotates, the material
undergoes a certain amount of stirring and mixing and the hot gases pass along the drum but usually in
the opposite direction.
ABSTRACT:
The Mixing and Nodulizing Drum (MND) is a part of Sinter plant used for mixing the ingredients with
blast furnace fines before feeding the same to the sinter machine. An MS plate is cold rolled in this
process and the ends of the plate are seam welded. When it comes to the seam welding of metal plates
the various conventional arc welding process used are Shielded metal arc welding(SMAW), Submerged
arc welding(SAW) and Gas metal arc welding(GMAW).
A detailed analysis of each welding process is enclosed in this project wherein characteristics such as
Electrode selection, welding angle, welding speed, flux coating, base and filler materials, welding
positions, weld joints, current-voltage requirements, heat treatment, etc. are discussed. The advantages,
limitations, applications of each welding process are different from each other.
Finally, after joining the plates, these are tested for strength of the weld by different testing methods
which include both destructive and non-destructive testing. If any welding defects are found during the
testing process, these are terminated by back-grinding the defected part.
FEATURES:
The assembly weighing about 65 Million Tonnes is manufactured and machined in a single piece and in a
single setting for M/s JSW Steel Limited for their 4.0 Million Tonnes expansion project.
The Girth Gear is also machined and teeth are cut in a shop and sent to site separately.
The final machining of the entire assembly of shell fitted with tires and girth gear flange is carried out on
gigantic 20 m lathe by providing two machined spiders at both ends.
For the development of drum, the plate is to be passed into a rolling machine.
Rolling is a metal forming process in which metal stock is passed through a pair of rolls.
Hot rolling
Cold rolling
If the temperature of the metal is above its recrystallization temperature, then the process is termed as
hot rolling.
If the temperature of the metal is below its recrystallization temperature, the process is termed as cold
rolling.
After rolling, the plate is joined by means of welding processes. They are
Longitudinal Seam welding: This process is achieved only when the ends of plates of the same section
are to be welded.
Circumferential seam welding: This process is achieved when different sections are joined together by
welding processes.
Both Longitudinal Seam welding and circumferential seam welding processes are achieved by welding
processes. They are
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
11. What is the Present and Future Scope of Powder Metallurgy? Mechanical Engineering Projects
Powder Metallurgy-Present and Future Scope: Production of components by taking initial methods in the
form of powder is called Powder Metallurgy. In this article, I am going to explain what is the Present and
Future Scope of Powder Metallurgy with its advantages and disadvantages in a detailed manner.
Utilized in Germany for producing Tungsten carbide cutting tools after 1stWorld war.
Definition:
Production of components by using initial methods in the form of powders is known as powder
metallurgy.
**For failures and Differences of “Red Brick Formation and Powder Metallurgy”, refer PPT
1.Production of Powders:
The molten liquid will break into spherical droplets and are cooled in quench medium.
2.Mixing/Blending:
3.Compaction:
Wet condition of powder mixture will be kept in the mold and is subjected to compression load under
pressure.
The compact possesses low strength compared to the final strength of component called Green
Strength.
Sintering
Due to this chemical bonds will form among atoms and thereby, strength increases.
After sintering, the compact will achieve tremendous strength called as final strength.
Advantages
In Superhard cutting tool bits, the tips will be coated with Fe3C, WC, SIC coatings by PMP.
Dis-Advantages
Powder metallurgy components are expensive compared to General alloy formation method.
Al, Mg, Sb, Bi, As Ti powders, should not be used because they will undergo explosion at the time of
compaction.
Hitachi chemicals:
Engaged in the development of wear-resistant parts, structural parts, magnetic parts(soft magnetic
materials) for the development of high-performance parts as next-generation products.
This is the detailed explanation of the above project which is categorized under Mechanical Engineering
Projects.
The Updated 650+ Mechanical Engineering Projects Ideas of all Domains are presented below. Check the
project type of your choice.
A Project on Automatic Vehicle Over Speed Indication And Controlling System
Performance and emission study of bio-diesel engine using an electronic fuel injection system
GPS Based Automatic Vehicle Accident Information System –Three and Four Wheeler
A Project on Smoke and LPG Gas Detection Robot with Wireless Control
Stress analysis of functionally graded discs under mechanical and thermal loads in ANSYS software.
Effect of friction stir welding parameters of speed on the transient temperature distribution of Al 360&
7475.
Tool life performances, wear mechanisms and surface roughness characteristics when turning austenized
and quenched AISI 52100 Bearing Steel with Ceramics and CBN/TiC cutting tools..
Investigation of Film Cooling Strategies of CFD versus Experiments-Potential for Using Reduced Models
Heat Transfer in an Automotive Turbocharger Under Constant Load Points: a Computational Investigation
A Project on Fabrication Of Electricity And Water Pumping System Using Wind Mill
A Project on Solar based advanced vehicle movement system using the windmill
A Project on Fabrication of basin type solar still multiple floating porous absorbers
A Project on Performance and emission study of a diesel engine using fuel ionizer for various biodiesel
mode
CFD analysis of fluid flow and heat transfer in a single tube-fin arrangement of an automotive radiator
Thermal conductivity and latent heat thermal energy storage characteristics of Paraffin/Expanded
Graphite Composite as Phase change material.
Experimental investigation of the discharge valve dynamics in a reciprocating compressor for the trans-
critical CO2 refrigeration cycle.
Design of a car air conditioning system based on an absorption refrigeration cycle using energy from the
exhaust gas of an internal combustion engine.
Transient modeling of hybrid loop heat pipe systems with multiple evaporators
A Project on A compact dynamic model for household vapor compression refrigerated systems
Natural convective heat transfer from a narrow vertical flat plate with a uniform surface heat flux and
with different plate edge conditions
Analytical investigation of rake contact and friction behavior in different metal cuttings
Optimization of high speed turning parameters of superalloy Inconel 718 material using Taguchi
technique.
Die design and analysis of progressive tool for coca cola bottle cap
Developments of a hot forging life of a die. A Project on Artificial Neural Network Based Autonomous
Mobile Robot
Automatic Accident Avoiding System In Pneumatic Bend And Bend Removing Machines
Coffee Maker
Hybrid Vehicle
A unified approach to the analysis of unidirectional and bi-directional parallel flow heat exchangers
Stall characteristics and tip clearance effects in forward swept axial compressor rotors
Calculating the heat transfer rate by varying cooling fluid for engine cylinder fins.
Heat transfer analysis and optimization of engine fins of varying geometry and thermal conductivity.
Gasifier
Fuel Injection
Fabrication of automatic vehicle over speed controlling system for school zone (prototype model)
Application of evaporation air cooler coupled with the solar water heater for dehumidification of indoor
air
A Project on VIVACE (vortex induced vibration aquatic clean energy) in the generation of clean and
renewable energy from fluid flow
Design of absorption refrigeration system driven by engine exhaust gas for vehicles
Vibration analysis of delaminated composite beams using analytical and FEM models.
Finite Element analysis of the effect of motorcycle helmet material against impact velocity during an
accident
Strengthening car bumper in load bearing direction by the usage of materials of Impact ABS Plastic and
Carbon Fiber-Reinforced Polymer IM7.
3D Modeling and Finite Element Analysis of Human Bone using ANSYS software
Composite material reinforcement of the leaf spring for the material Glass Carbon Composite.
Bridge truss optimization under moving load using continuous and discrete design variables in
optimization methods.
Air and fuel flow interaction in the combustion chamber for Various injector locations
CFD simulation and field application by Mitigating snowdrift at the elevated SANAE IV research station in
Antarctica
Analysis of water flow for Laminar & Turbulent Flow in Conventional Water Tap
Numerical Solution of Navier – Stokes Equations for Separating and Reattaching Flow over a Double
Steps Expansion and Contraction
Experimental Evaluation And Buckling Analysis Of Woven Glass Epoxy Laminated Composite Plate
A Project on Experimental Evaluation And Finite Element Analysis of Composite Leaf Spring For
Automotive Vehicle
A Project on Surface Fracture Analysis of Glass Fiber Reinforced Epoxy Composites Treated With Different
Type Of Coupling Agent
Finite Element Analysis And Experimental Evaluation Of Bonded, Riveted And Hybrid Joints In Glass Fiber
Epoxy Composite Laminates for Aircraft Structure
A Project on Application Of Coir Fibers as Concrete Composites For Disaster Prone Structures
Mechanical Characterization and Comparison of Glass Fiber Reinforced Aluminum Alloy (GFRAA) to
Improve the strengthening
A Project on Experiment For Bending Analysis Of 3-Phase Composite Plate In Ship Structure
Composite material reinforcement of the leaf spring for the material Glass Carbon Composite.
3D Modeling and Finite Element Analysis of First Molar Human Tooth using ANSYS Software.
Effect of Orientation angle of Elliptical hole on residual stresses and expansion of Plastic zone in
thermoplastic composite plates under In-plane loading.
A Project on Injection Mould tool design and Mould flow analysis of Exhaust fan in ANSYS software.
Influence of cutting parameters on thrust force and torque in the drilling of Aluminum, Cast Iron, EN 28.
A Project on Mechanical Properties of Friction Stir butt welding of AI7475 & AI 6061.
Comparison And Experimental Investigation of Glass Fiber And Natural Fiber Reinforced Composites
Experimental Characterization Of Interlaminar Shear Strength And Flexural Strength Of Glass And Carbon
Composite Laminates Under repeated Curing.
A Project on Fatigue And Fracture Of Fiber Composites Under Combined Interlaminar Stresses
A Project on Effect Of Strain Rate On The Tensile Failure Of Glass-Fiber Braided Tubes
A Project on Experimental Evaluation And Buckling Analysis Of Woven Glass Epoxy Laminated Composite
Plate For Aircraft Applications
A Nickel-Carbon-Fiber Composite For Large Adaptive Mirrors: Fabrication Methods And Properties
Fatigue Behavior Study On Repaired Aramid Fiber/Epoxy Composites Fracture Toughness Of Through-
Thickness Reinforced Composites
A Project on Mechanical Behavior of Bagasse Fiber Epoxy Composites At Liquid Nitrogen Temperature
A Project on Impact Analysis And Experimental Evaluation On Stitched And Unstitched Fiber Glass –
Epoxy Laminate to Increase Strength In Aircraft Structures
Evaluation of CFD Sub-Models for the Intake Manifold Port Flow Analysis
A Project on CFD Analyses Of The Gas Flow Inside The Vessel Of A Hot Isotactic Press
CFD based process on the modeling of a rotary furnace for Aluminum scrap melting
A Project on CFD analysis of combustion and emissions to study the effect of compression ratio and
biogas substitution in a diesel engine
A Project on CFD Solution of Internal (shock tube and coquette flow) & External (Airfoil and cylinder)
flow
CFD Analysis of Mixing and Combustion of a Scramjet Combustor with a Planer Strut Injector
A Project on CFD analysis for transient turbocharger flows by varying flow rate.
A Project on Airplane visual landing gear arrangement with tire pressure Inflation system
Design and Analysis of Universal Cutter (Especially for Coconut and Areca nut)
A Project on Automatic speed breaker depending upon vehicle over speed control
Fabrication of Mechanical Grass Cutter Machine(Using Bevel Gears Arrangement) (prototype model)
Fabrication of electricity and water pumping system using windmill (prototype model)
Fabrication of electricity from the road with kinetic energy (prototype model)
A Project on Generation of electricity from ocean waves using rack and pinion mechanism
280+Updated list of Mini Projects for Mechanical Engineering 3rd Year Students
This is the complete list of 650+Updated Mechanical Engineering Projects Ideas of all Domains in a
detailed manner.If this article is helpful to you.then post your valuable comments from the comments
section.
32
SHARES
Share
Tweet
PREVIOUS POST
NEXT POST
admin
ADMIN
One Comment
mymdengineering
Reply
Leave a Reply
This site uses Akismet to reduce spam. Learn how your comment data is processed.
CAREERS (7)
Companies/Colleges (3)
Jobs (84)
Machining (8)
News (12)
Production (25)
QUIZ (3)
admin
FOLLOW US ON FACEBOOK..
(100+Updated) Thermal Projects List for Mechanical and Diploma Students(100+Updated) Thermal
Projects List for Mechanical and Diploma Students
- 40,206 Views
280+Updated list of Mini Projects for Mechanical Engineering 3rd Year Students280+Updated list of Mini
Projects for Mechanical Engineering 3rd Year Students
- 37,289 Views
- 32,765 Views
- 23,596 Views
- 19,555 Views
- 19,094 Views
(240+Updated) Mechanical Projects list for Diploma and Mechanical Students(240+Updated) Mechanical
Projects list for Diploma and Mechanical Students
- 17,477 Views
- 16,864 Views
MECHANICAL PROJECTS:
Major Projects
Mini Projects
ANSYS Tutorial
Creo Installation
PLASTICS:
Types of Plastics
Blow Molding
Injection Molding
Compression Molding
CASTING PROCESS:
Casting Process-Basics
Sand Casting
Die Casting
WELDING PROCESS:
Welding Process-Basics
Electric Arc Welding
BLOG STATS
982,831 hits
Machining Process
Milling Operations
Additive Manufacturing
Grinding Wheel
MECHANICAL VIBRATIONS:
Condition Monitoring
DESIGN:
Just In Time Manufacturing & JITSR
Material Selection,Phases,Springback
Types of Strain
Types of Fits
Sine bar-Explanation
Stress-Strain Curve
NON-TRADITIONAL MACHINING:
Ultrasonic Machining
Electrochemical Machining
Limitations of NTM
Mechanical Colleges,schools,universities
THERMAL ENGINEERING:
Boiler Machine
MUST CHECK:
ONLINE TESTS:
Partnership Problems – Online QUIZ
Linear Algebra-GATE
Differential Equations-GATE