Professional Documents
Culture Documents
Service Intervals
670G and 670GP (PIN: 1DW670GX_ _C624392—C634753) (PIN: 1DW670GX_ _D624392—D634753)
672G and 672GP (PIN: 1DW672GX_ _C624392—C634753) (PIN: 1DW672GX_ _D624392—D634753)
As Required
□ Clean battery terminals and tighten clamps □ Inspect belts
□ Clean or replace cab fresh air and cab recirculation filters □ Clean engine air intake filter
□ Lubricate circle pinion □ Replace starting fluid cylinder—if equipped
□ Inspect and adjust tire pressure □ Drain water and sediment from fuel tank sump
□ Adjust wear insert clearance of blade circle and draft frame wear □ Adjust or replace blade side shift wear inserts
inserts
□ Adjust or replace blade lift cylinder sockets □ Calibrate hydraulic valves—if equipped
□ Lubricate saddle locking pin holes □ Check and clean rear camera—if equipped
□ Drain primary fuel filter/water separator □ Add coolant extender as indicated by COOL-GARD™ II test strips
□ Calibrate transmission control unit (TCU) □ Drain auxiliary fuel filter and water separator—if equipped
□ Calibrate cross slope sensors—if equipped □ Calibrate 6WD controller—if equipped
□ Clean radiator, oil cooler, charge air cooler, fuel cooler, and air conditioner condenser
Every 50 Hours
□ Lubricate frame hinge pivots □ Lubricate front axle lean bar pivot
□ Lubricate lift cylinders □ Lubricate front axle steering pins
□ Lubricate draft frame ball □ Lubricate tie rod ends
□ Lubricate front mounted scarifier—if equipped □ Lubricate steering cylinders
□ Lubricate front dozer blade—if equipped □ Lubricate midmount scarifier—if equipped
□ Lubricate Balderson™ style front lift group—if equipped □ Lubricate circle side shift cylinders
□ Lubricate front axle oscillation pin □ Lubricate saddle locking pin
□ Lubricate front axle lean pivot casting pins
Required Parts
Initial
Every Every Every Every Every Every
Service—
Description Part Number 250 500 1000 2000 4000 6000
250
Hours Hours Hours Hours Hours Hours
Hours1
Transmission Oil Filter AT335492 1 1 1 1
Axle Housing Oil Filter AT335492 1 1 1 1
Auxiliary Fuel Filter and Water
AT365869 1 1 1 1 1
Separator—If Equipped
Continued on next page MB60223,00052FC -19-12DEC19-1/2
MB60223,00052FC -19-12DEC19-2/2
Initial
Every Every Every Every Every Every
Service—
Description Part Number 250 500 1000 2000 4000 6000
250
Hours Hours Hours Hours Hours Hours
Hours1
Engine 6068HDW75 (6.8L Tier 2/Stage II Engine)
John Deere PLUS-50™ II Engine 26.1 L 26.1 L 26.1 L 26.1 L 26.1 L 26.1 L
TY266742
Oil (6.9 gal) (6.9 gal) (6.9 gal) (6.9 gal) (6.9 gal) (6.9 gal)
48.5 L
COOL-GARD™ II Pre-Mix TY26575
(12.8 gal)
Coolant Extender TY26603 As Required
3
Fluid Analysis Kits
Diesel Engine Oil AT346594 1 1 1 1 1 1
Power Train (transmission oil,
AT303189 4 4 4 4 4
axle oil, and tandem oil)
Hydraulic Oil AT303189 1 1 1 1 1
Diesel Fuel AT180344 1 1 1 1 1
Engine Coolant TY26873 1 1 1 1 1
COOL-GARD™ II 3-Way Test
TY26605 1 1 1 1
Strips
1
Perform initial service once after the first 250 hours of operation.
2
See operator's manual for recommended oil type and oil viscosities based on operating temperatures.
3
Based on fluid analysis results, intervals may need to be adjusted for your operating conditions. Consult your local John Deere dealer.
Hy-Gard is a trademark of Deere & Company
Hydrau is a trademark of Deere & Company
PLUS-50 is a trademark of Deere & Company
COOL-GARD is a trademark of Deere & Company
MB60223,00052FC -19-12DEC19-3/2