Professional Documents
Culture Documents
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 1 OF 19
S.R. Vietnam WRITTEN PRACTICE.
AMIGOS Ltd.
WRITTEN PRACTICE
FOR
OF
IN ACCORDANCE WITH
ASNT - SNT - TC - 1A
1996 Edition
CONTENTS.
1.0 INTRODUCTION
2.0 DEFINITION
3.0 SCOPE
7.0 EXAMINATION
9.0 CERTIFICATION
10.0 RECERTIFICATION
12.0 ATTACHMENTS
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 3 OF 19
S.R. Vietnam WRITTEN PRACTICE.
1.0 INTRODUCTION.
1.2 This written practice is established for the qualification and certification of non-
destructive testing personnel of AMIGOS Ltd. whose specific jobs requires
appropriate knowledge of the technical principles underlying the non-destructive
tests they perform, witness, monitor or evaluate.
1.3 This written practice has been developed in accordance with the American
Society for Non-destructive testing, (ASNT) Recommended Practice No. SNT -
TC - 1A 1996 Edition.
2.0 DEFINITION
(12) Training: the organised program developed to impart the knowledge and
skills necessary for qualification.
3.0 SCOPE
3.1 This written practice shall apply to all NDT personnel employed by AMIGOS
Ltd. and the certifying agency.
3.3 This written practice shall be managed by the Company NDT Level III or his
designate who has been appointed by the General Manager of AMIGOS Ltd. and
approved by the Quality Control Manager.
4.1 There are three basic levels of qualification used by NDT personnel AMIGOS
Ltd.. Each basic level has the following responsibilities:
.
Level I:
i. Perform calibrations, tests and evaluations for determining the acceptance and
rejection of tested item in accordance with specific written instruction.
ii. Record test results.
iii. Receive instructions and supervision from a certified level II or III individual.
Level II:
i. Set up and calibrate equipment.
ii. Interpret and evaluate results with respect to applicable codes, standards and
specification.
iii. Organise and report the results of non-destructive tests.
iv. Be familiar with scope and limitations of each method for which individual
are certified.
v. Train and guide level I personnel and trainees.
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 5 OF 19
S.R. Vietnam WRITTEN PRACTICE.
Level III:
i. Be responsible for NDT operations to which assigned and for which certified.
ii. Be responsible for the training and examination of NDT level I and level II
personnel in the methods for which certified.
iii. Interpret test results in terms of applicable codes, standards, specification, and
procedures.
iv. Establish methods and test techniques and authorise use of all NDT
procedures to be used by level I and level II on behalf of AMIGOS Ltd.
v. Sufficiently familiar with applicable materials, fabrication, and product
technology to establish techniques and assist in acceptance criteria where non
are available.
vi. Be generally familiar with other appropriate NDT methods.
vii. Be responsible (in the methods for which certified) for the training and
examination of NDT Level I and Level II personnel.
4.2 While in the process of being initially trained, qualified, and certified, an
individual should be considered a Trainee. A trainee shall work with a certified
individual. The trainee shall not independently conduct, interpret, evaluate, or
report the results of any NDT.
5.1 Basic level I and level II personnel initially certified to conduct NDT under this
written practice shall have or exceed the NDT training hours shown in Table-1,
depending upon each candidate’s formal educational background.
5.2 This formal NDT training shall be conducted either by AMIGOS Ltd. Company
Level III individual(s) or by an outside agency or other certified individual
selected and approved by Quality Manager of AMIGOS Ltd.
5.3 The training program shall follow the Recommended Training Course Outline for
each examination as shown in SNT-TC-1A 1996 Edition.
5.4 The training course outlines may be modified by deleting or adding topics to meet
the employer specific applications or for limited certification.
5.5 Procedures and test techniques that individuals will encounter in their specific
assignments, and applicable instructions, specifications and codes used by
AMIGOS Ltd. and AMIGOS Ltd. customer, shall be part of each candidate’s
informal on the job training under the co-ordination of the NDT personnel
designated by Level III individual(s).
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 6 OF 19
S.R. Vietnam WRITTEN PRACTICE.
5.6 The minimum initial experience requirement for Level I and Level II personnel is
summarised in Table II. The experience factor in months is based on a normal 40
hours week. (175 hours per month). When work is performed in excess of 40
hours per week, credit may be based on total hours. Records substantiating
qualification shall be kept on either a monthly or hourly basis.
6.1 This formal NDT training shall be conducted either by AMIGOS Ltd. - certified
Level III individual(s) or by an outside agency or other certified individual
selected and approved by Quality Manager of AMIGOS Ltd..
6.2 The training program shall follow the Recommended Training Course Outline for
each examination as shown in SNT-TC-1A1996 Edition.
RT-Training Course Outline-TC-1
MT-Training Course Outline-TC-2
UT-Training Course Outline-TC-3
PT-Training Course Outline -TC-4
6.3 The training course outline may be modified by deleting or adding topics to meet
the employer specific applications or for limited certification.
6.4 Company NDT Level III is responsible for the training requirements and syllabus
of the completed course and documentation of training activities.
6.5 Training courses will be conducted by the NDT Level III or his designated NDT
Instructor (in-house or outside agency). Personnel with specialised expertise but
who are not qualified in NDT may be utilised for providing training (e.g. welding
technology, radiation safety, etc.).
6.6 Procedures and test techniques that individuals will encounter in their specific
assignments, and applicable instructions, specifications and codes used by
AMIGOS Ltd. and AMIGOS Ltd. customer. Shall be part of each candidate’s
informal on the job training under the co-ordination of the NDE personnel
designated by Level III individual(s).
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 7 OF 19
S.R. Vietnam WRITTEN PRACTICE.
7.0 EXAMINATION.
7.1 To be considered for examination, NDT personnel must meet the training and
experience requirements of this document.
ii) When the NDT method requires colour contrast differentiation, a colour
vision test shall be required to demonstrate the capability of distinguishing
and differentiating contrast among colours or shades of grey used in the method.
This should be conducted upon initial certification and at three years intervals
thereafter.
7.2.1 Eye acuity test may be conducted by the NDT level III or his designee.
i) Each level I and level II candidate shall be given a general, objective type (for
example: multiple choice) and close book written examination addressing
basic principle of each method for which certification is sought. Necessary
data, such as graphs, tables, specification, procedures, and codes may be
provided.
ii) The content of this general examination shall meet or exceed the example
questions in the applicable SNT-TC-1A Supplement. The Supplement
questions should not be used verbatim for qualification examinations.
Minimum numbers of question shall be as shown in the Table-3 for each
written examination.
iii) This examination will either be administered as part of the organised training
program or given separately when experienced personnel are being examined
for recertification or for initial certification when coming from a former
employer and complying with this written practice.
ii) The content of the specific examination shall be constructed to evaluate the
ability of the candidate to effectively use the applicable specifications, codes,
etc. To perform and/or evaluate the results to the degree necessitated by the
anticipated qualification level. Minimum number of question shall be as
shown in the Table-3 for each written examination.
iii) This examination will either be administered as part of the organised training
program or given separately when experienced personnel are being examined
for recertification or for initial certification when coming from a former
employer and complying with this written practice.
iv) The examination should address common specification, codes and acceptance
criteria used by AMIGOS Ltd. and AMIGOS Ltd. customers such as ASME
Section V, ASME Section VIII, ASME Section IX, AWS D1.1 and etc.
Level I
Level II
ii) The grade for each of the parts shall be at least 70 percent.
iii) The composite examination grade for each candidate shall be simple average
(mean) of the grades obtained in the three parts of the written and practical
examination.
7.7 Re-examination
8.1 To be considered for certification as NDT Level III, a candidate should satisfy
one of the following criteria.
i) Have graduated from a minimum four year college or university curriculum
with a degree in engineering or science, plus one year’s experience in NDT in
an assignment comparable to that of an NDT Level II in the applicable NDT
method(s), or:
ii) Have completed with passing grades at least two years of engineering or
science study at a university, college or technical school plus two year’s
experience in assignments at least comparable to that of an NDT Level II in
the applicable test method(s). or:
iii) Have four years experience in an assignment at least comparable to that of an
NDT Level II in the applicable NDT method(s).
8.2 The examination for NDT Level III is described fully in Table 4.
8.3 A valid endorsement on an ASNT NDT Level III Certificate fulfils the
examination criteria for Basic examination and Method examination as shown in
Table 4.
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 10 OF 19
S.R. Vietnam WRITTEN PRACTICE.
8.4 The company may delete the specific examination described in Table 4 if the
candidate has a valid ASNT NDT Level III Certificate in the Method and if
documented evidence of experience exists, including the preparation of NDT
procedure to codes, standards or specifications and the evaluation of test results.
9.0 CERTIFICATION.
9.1 The certification of all levels of NDT personnel is the responsibility of the
company.
9.3 At the option of the company, an outside inspection agency may be engaged to
provide NDT level III services. In such cases, the responsibility for certification
must still be retained by the company through the quality control manager.
Name of candidate.
Level of certification and NDT method.
Educational background and years of experience.
Statement indicating satisfactory completion of training.
Result of vision examination.
Result of all written examination and composite grades
Date of certification and re-certification.
Signature, printed name, and title of the PRI certifying representative
9.5 All NDT Level I and II certificates so issued after meeting the requirement of this
written practice shall bear the signatories of the company NDT Level III and
AMIGOS Ltd. Q.C Manager.
10. RECERTIFICATION
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 11 OF 19
S.R. Vietnam WRITTEN PRACTICE.
10.1 All NDT Level I and II personnel shall be recertified every three years base upon
evidence of continuing satisfactory performance as judged and documented by
NDT Level III for the applicable method.
10.2 Where a weakness is identified by the NDT Level III in the technical
performance of an individual, supplemental training, and specific examinations
may be used, at the discretion of the NDT Level III, to upgrade the individual
prior to completion of recertification.
10.3 Level III personnel shall be recertified every five years by the company
representative by verifying that the individual’s ASNT NDT Level III certificate
is current in each method for which recertification is sought.
10.4 NDT Level I and II may be re-examined at any time at the discretion of the
employer and have their certification extended or revoked.
10.5 NDT personnel will be re-examined and re-certified when service in a particular
discipline is interrupted by a period of 12 months or more.
11.1 The certification of all NDT personnel shall terminate upon a period of one year
during which no NDT-related work is performed in the method(s) certified.
11.2 All NDT personnel certified by AMIGOS Ltd. leaving the employment of
AMIGOS Ltd. are revoked of their certificates at the time of employee’s
separation.
11.3 NDT personnel whose certification has been terminated may be recertified to his
former level within the one year of his termination.
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 12 OF 19
S.R. Vietnam WRITTEN PRACTICE.
12.0 ATTACHMENTS
TABLE 3: Minimum No. Of Question in Written Examination for Level I & II.
TABLE 4: Examination Structure and Number of Question for NDT Level III.
Page 1 of 1
Method RT MT UT PT
Technique UTM
NDT LEVEL I II I II I II I II I II
At least 2 29 35 8 4 24 40 4 4 4 4
years of
engineering or
science study
in a university
college or
technical
school.
High school 39 40 12 8 40 40 4 8 4 8
graduation.
Method RT MT UT PT
Technique RI UTM
NDT LEVEL I II I II I II I II I II
Month 3 9 1 3 3 9 1 2 1 2
LEGEND
RT - Radiographic Testing UT - Ultrasonic Testing
PT - Penetrant Testing UTM - Ultrasonic Thickness Measurement
MT - Magnetic Particle Testing (Digital Measurement)
Page 2 of 2
Notes:
i) If a person is being qualified directly to level II with no time at Level I, the required
experience shall consist of the sum of the times required for Level I and Level II and
the required training shall consist of the sum of the hours required for Level I and
Level II.
ii) All personnel shall have a high school level education.
iii) Where certification in two or more methods is sough, credit for simultaneous initial
experience is considered valid only when the candidates spend a minimum of 25% of
work time on each method and the remaining time on NDT related activities.
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 15 OF 19
S.R. Vietnam WRITTEN PRACTICE.
APPENDIX I Page 1 of 1
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 16 OF 19
S.R. Vietnam WRITTEN PRACTICE.
Grading of Practical Examination for Radiographic Testing and Radiographic
Interpretation
NDT Level I Radiographic Testing
1. All candidates shall demonstrate they can follow the written instructions for producing
radiographs in one of the three techniques below: DWDI, SWSI, and DWSI.
2. There will be a checklist containing not less than 10 checkpoints in order to assess the
candidate’s performance.
3. All candidates shall demonstrate they can follow all the safety procedures before, during and
after the test.
4. An oral test will be given to assess the knowledge of RT safety aspects including use of the
RT safety equipment, and other technical knowledge.
Radiographic Interpretation
1. A total of 20 radiographs will be interpreted by the individuals who wish to qualify for
radiographic interpretation.
2. No major indications as reported in the master answer sheets by the NDT Level III shall be
missed.
3. The candidate’s comments on the quality of radiographs will be considered during grading
and the sensitivity of each radiograph shall be calculated and density shall be measured.
4. The candidate will choose a code or specification eg. AWS D1.1 or ASME VIII and write
down their interpretation of 20 radiographs.
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 17 OF 19
S.R. Vietnam WRITTEN PRACTICE.
APPENDIX II
Grading of Practical Examination for Ultrasonic Testing
2. UT testers shall submit a written report of the inspection of the test piece with a sketch
containing the nature, size (length), and location along the weld and position within the weld
cross section of all reported defects.
3. No major indications as reported in the master answer sheets by the NDT Level III shall be
missed.
4. The candidate shall satisfy the examiner that techniques, limitation of test method,
code/standard, problem etc. are understood.
5. There will be a checklist containing not less than 10-check point to assess the candidate’s
performance.
QUALITY CONTROL ASP/002/01
AMIGOS Ltd.
REV: 0
Dong Xuyen Industrial Park. PROCEDURE. ISSUE: 2
Ward 10.
Vung Tau City _________________________ DATE: 20/05/01
PAGE 18 OF 19
S.R. Vietnam WRITTEN PRACTICE.
APPENDIX III
Grading of Practical Examination for Ultrasonic Thickness Measurement
APPENDIX V
Grading of Practical Examination for Liquid Penetrant Testing