Professional Documents
Culture Documents
0
AU OPTRONICS CORPORATION
( ) Preliminary Specification
( V ) Final Specification
15
Model Name M195XTN01.0
4/
/0
14
20
Customer Date Approved by Date
On
nly
eO
Howard Lee Dec 20, 2013
Us
al
rn
Contents
1 Handling Precautions.............................................................. 4
2 General Description ................................................................ 5
2.1 Display Characteristics....................................................................................................... 5
2.2 Absolute Maximum Rating of Environment ........................................................................ 6
2.3 Optical Characteristics ....................................................................................................... 7
3 TFT-LCD Module.................................................................... 11
3.1 Block Diagram.................................................................................................................. 11
3.2 Interface Connection........................................................................................................ 12
3.2.1 Connector Type....................................................................................................... 12
15
3.2.2 Connector Pin Assignment...................................................................................... 12
4/
3.3 Electrical Characteristics.................................................................................................. 14
/0
3.3.1 Absolute Maximum Rating ...................................................................................... 14
14
3.3.2 Recommended Operating Condition....................................................................... 14
20
3.4 Signal Characteristics ...................................................................................................... 15
On
3.4.1 LCD Pixel Format.................................................................................................... 15
3.4.2 LVDS Data Format .................................................................................................. 15
nly
3.4.3 Color versus Input Data .......................................................................................... 16
eO
3.4.4 LVDS Specification.................................................................................................. 17
3.4.5 Input Timing Specification ....................................................................................... 19
Us
3.4.6 Input Timing Diagram .............................................................................................. 20
al
5 Reliability Test...................................................................... 28
en
7 Mechanical Characteristics.................................................... 30
nf
Record of Revision
14
15
4/
/0
14
26
20
On
nly
27
eO
Modify note description
Us
al
rn
30
te
In
AR
ST
32
or
lF
tia
en
id
nf
Co
O
AU
1 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
15
8) Do not press the reflector sheet at the back of the module to any directions.
4/
9) In case a TFT-LCD Module has to be put back into the packing container slot after once it
/0
was taken out from the container, do not press the center of the LED lightbar edge. Otherwise
14
the TFT-LCD Module may be damaged.
20
10) Insert or pull out the interface connector, be sure not to rotate nor tilt it of the TFT-LCD
On
Module.
11) Do not twist nor bend the TFT -LCD Module even momentary. It should be taken into
nly
consideration that no bending/twisting forces are applied to the TFT-LCD Module from
outside. Otherwise the TFT-LCD Module may be damaged.
eO
12) Please avoid touching COF position while you are doing mechanical design.
Us
13) When storing modules as spares for a long time, the following precaution is necessary:
Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep
al
2 General Description
This specification applies to the 19.5 inch wide Color a-Si TFT-LCD Module M195XTN01.0.
The display supports the HD - 1366(H) x 768(V) screen format and 16.7M colors (RGB 6-bits +
Hi-FRC data). The input interface is 1-channel LVDS and this module doesn’t contain an driver
board for backlight.
15
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm]
4/
493.92 (19.45”)
Active Area [mm] 434.0 (H) x 235.8 (V)
/0
Pixels H x V - 1366(x3) x 768
14
Pixel Pitch [um] 317.7 (per one triad) ×307
Pixel Arrangement - R.G.B. Vertical Stripe
20
Display Mode - TN Mode, Normally White
[cd/m2]
On
White Luminance ( Center ) 200 (Typ.)
Contrast Ratio - 600 (Typ.)
Response Time [msec] 5 (Typ., on/off)
nly
Power Consumption [Watt] 8.5 (Typ.)
(LCD Module + Backligh unit) LCD module : PDD (Typ.)=2.5 @ Black pattern,Fv=60Hz
eO
Backlight unit : PBLU (Typ.) =5.95 @Is=60mA
Us
Weight [Grams] 1380
Outline Dimension [mm] 452(H) × 263(V) × 10.5(D) Typ.
al
Temperature Range
Operating [oC] 0 to +50
AR
15
HST Storage Humidity 5 90 [%RH]
4/
/0
Note 2-1: Temperature and relative humidity range are shown as the below figure.
14
1. 90% RH Max ( Ta ≦39℃)
20
2. Max wet-bulb temperature at 39℃ or less. ( Ta ≦39℃)
On
3. No condensation
nly
eO
Us
al
rn
te
In
AR
ST
or
Note 2-2
Lw White Luminance (Center of screen) 160 200 - [cd/m2]
By SR-3
15
Note 2-3
Luni [%]
4/
Luminance Uniformity (9 points) 75 80 -
By SR-3
/0
Note 2-4
CR Contrast Ratio (Center of screen) 360 600 - -
14
By SR-3
20
θR Horizontal Viewing Angle Right 35 45 -
(CR=10)
On
θL Left 35 45 -
ΦH Vertical Viewing Angle Up 15 20 -
nly
ΦL (CR=10) Down 40 45 - Note 2-5
[degree]
eO
θR Horizontal Viewing Angle Right 35 45 - By SR-3
θL (CR=5) Left 35 45 - Us
ΦH Vertical Viewing Angle Up 15 20 -
(CR=5)
al
ΦL Down 40 45 -
rn
Note 2-6
TF Response Time Falling Time - 1.2 2.5 [msec]
In
By TRD-100
- Rising + Falling - 5 8
AR
Note 2-7
CT Crosstalk - - 1.5 [%]
By SR-3
O
AU
Note 2-8
FdB Flicker (Center of screen) - - -20 [dB]
By SR-3
15
4/
/0
Measured distance (50cm)
14
20
LCD Panel TFT-LCD Module
On
nly
Center of the screen
eO
Us
Note 2-3: Luminance Uniformity Measurement
al
rn
Definition:
Minimum Luminance of 9 Points (P1 ~ P9)
te
Luminance Uniformity
Maximum Luminance of 9 Points (P1 ~ P9)
In
AR
Definition:
Luminance of White pattern
Contrast Ratio
Luminance of Black pattern
a. Measured position: Center of screen (P5) & perpendicular to the screen (θ=Φ=0°)
Definition: The angle at which the contrast ratio is greater than 10 & 5 .
15
a. Horizontal view angle: Divide to left & right (θL & θR)
4/
Vertical view angle: Divide to up & down (ΦH &ΦL)
/0
14
20
On
nly
eO
Us
al
rn
The output signals of photo detector are measured when the input signals are changed
In
from “Black” to “White” (rising time, TR), and from “White” to “Black” (falling time, TF),
AR
respectively. The response time is interval between the 10% and 90% of optical
ST
response. (Black & White color definition: Please refer section 3.4.3)
or
% TF TR
lF
tia
10 0
90
en
Optical
id
respon se
10
Co
0
1 Frame 1 Frame
O
AU
Where
a.Maximum Horizontal Crosstalk :
CTH = Max. (| YBL – YAL | / YAL × 100 %, | YBR – YAR | / YAR × 100 %);
Maximum Vertical Crosstalk:
CTV = Max. (| YBU – YAU | / YAU × 100 %, | YBD – YAD | / YAD × 100 %);
b. YAU, YAD, YAL, YAR = Luminance of measured location without Black pattern
15
YBU, YBD, YBL, YBR = Luminance of measured location with Black pattern
4/
/0
14
20
On
nly
eO
Us
Note 2-8: Flicker measurement
al
rn
Gray level = L0
AR
ST
or
lF
b. Measured position: Center of screen (P5) & perpendicular to the screen (θ=Φ=0°)
Co
O
AU
3 TFT-LCD Module
3.1 Block Diagram
The following shows the block diagram of the 19.5 inch Color TFT-LCD Module.
15
Signal Converter Correction
4/
Signal D1 D4098
Connector
AUO ASIC G1
/0
X-Driver IC
VDD
14
Timing TFT-LCD
20
LVDS Controller 1366(x3) x 768
Receiver Mini LVDS
On
Transmitter Pixels
G768
nly
ASIC
eO
Control Board
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
3.2.2 Connector Pin Assignment
4/
/0
PIN # Symbol Description Remark
14
1 NC No connection
20
2 NC No connection
3 NC No connection
On
4 NC No connection
nly
5 NC No connection
6 NC No connection
eO
7 GND Ground
8 NC No connection
Us
9 NC No connection
al
10 NC No connection
rn
11 NC No connection
te
14 GND Ground
ST
17 GND Ground
lF
15
4/
/0
14
20
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
Symbol Description Min Typ Max Unit Remark
Power supply
4/
VDD 4.5 5.0 5.5 [Volt]
Input voltage
/0
Power supply - 0.5 0.6 [A] VDD= 5.0V, Black Pattern, Fv=60Hz
14
IDD Input Current (RMS)
0.6 0.7 [A] VDD= 5.0V, Black Pattern, Fv=75Hz
20
VDD Power - 2.5 3.0 [Watt] VDD= 5.0V, Black Pattern, Fv=60Hz
PDD
On
Consumption 3.0 3.5 [Watt] VDD= 5.0V, Black Pattern, Fv=75Hz
nly
Allowable VDD
eO
VDDrp - - 500 [mV] VDD= 5.0V, Black Pattern, Fv=75Hz
Ripple Voltage Us
Note 3-1: Inrush Current measurement:
al
Test circuit:
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
1st Line R G B R G B R GB R G B
15
4/
/0
14
1080
768 Line R G B R G B R GB R G B
20
On
3.4.2 LVDS Data Format
1365 1366
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
4/
/0
14
20
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
VCM +1.0 +1.2 +1.5 [V] VTH-VTL = 200mV
Voltage
4/
/0
LVDS Signal Waveform:
14
Use RxOCLK- & RxOCLK+ as example.
20
On
RxOCLK-
nly
RxOCLK+ eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
b. AC Characteristics:
Maximum deviation of
FDEV input clock frequency - ±3 %
during Spread Spectrum
Maximum modulation
FMOD frequency of input clock 200 KHz
15
-
during Spread Spectrum
4/
/0
14
Freq
20
Fmax
On
Fclk * FDEV
Fclk
nly
eO
Fmin Us
1
al
FMOD
rn
te
It only support DE mode, and the input timing are shown as the following table.
15
50 60 76
Th Period Tclk
4/
1454 1606 2047
/0
Tdisp (h) Active 1366 1366 1366 Tclk
Horizontal Section
14
Tblk (h) Blanking 88 240 681 Tclk
20
Fh Frequency 39.7 48.5 64.6 KHz Note 3-3
On
Tclk Period 10.6 12.8 17.3 ns 1/Fclk
LVDS Clock
Fclk Frequency 57.7 77.9 94.0 MHz Note 3-4
nly
eO
Note 3-3: The equation is listed as following. Please don’t exceed the above recommended value.
Us
Fh (Min.) = Fclk (Min.) / Th (Min.);
Fh (Typ.) = Fclk (Typ.) / Th (Typ.);
al
Note 3-4: The equation is listed as following. Please don’t exceed the above recommended value.
te
15
4/
/0
14
20
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
T1
Backlight Off
90% 90%
10%
10%
VDD T2
T5 T6 T7
15
4/
LVDS Signal VALID
/0
DATA
14
T3 T4
20
On
VSLED Backlight Off Backlight On Backlight Off
nly
eO
Power Sequence Timing Us
Value Remark
al
Symbol Unit
rn
T1 0.5 - 10 [ms]
In
T2 0 - 50 [ms]
AR
T3 500 - - [ms]
ST
T4 100 - - [ms]
Note 3-5
or
T5 0 50 [ms]
Note 3-6
lF
T7 1000 - - [ms]
en
id
Note 3-5 : Recommend setting T5 = 0ms to avoid electronic noise when VDD is off.
nf
Co
Note 3-6 : During T5 and T6 period , please keep the level of input LVDS signals with Hi-Z state.
O
AU
4 Backlight Unit
4.1 Block Diagram
The following shows the block diagram of the 19.5 inch Backlight Unit. And it includes 32 pcs LED
in the LED light bar. (4 strings and 8 pcs LED of one string).
15
+
4/
/0
VS
14
20
-
On
nly
eO
IS IS IS IS
Us
al
rn
Connector
te
In
AR
ST
or
lF
Manufacturer ENTERY
Backlight Connector
Part Number 3707K-S06N-21R
Manufacturer ENTERY
Mating Connector
Part Number H112K-P06N-13B (Locking type)
15
4/
/0
Backlight Connector dimension:
14
H V D 13.9 3.00 4.25, Pitch 1.0(unit mm )
20
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
4/
/0
14
20
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
4/
/0
14
20
PIN 1
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
15
4/
/0
14
20
Duty ratio= (A / B) X 100% ; (A: Pulse time, B: Period)
On
4.3.2 Recommended Operating Condition
nly
(Ta=25℃)
eO
Symbol Description Min. Typ. Max. Unit Remark
Us
100% duty ratio of LED
Is LED String Current - 60 66 [mA]
chip
al
rn
15
Note 4-2: ΔVs (Max.) = ΔVF X LED No. (one string);
4/
a. ΔVF: LED chip forward voltage deviation; (0.2 V , each Bin of LED VF)
/0
Note 4-3: PBLU (Typ.) = Vs (Typ.) X Is (Typ.) X 4 ; ( 4 is total String No. of LED Light bar)
14
20
PBLU (Max.) = Vs (Max.) X Is (Typ.) X 4 ;
On
Note 4-4: Definition of life time:
a. Brightness of LED becomes to 50% of its original value
nly
b. Test condition: Is = 60mA and 25℃ (Room Temperature)
eO
Note 4-5: Recommendation for LED driver power design:
Due to there are electrical property deviation in LED & monitor set system
Us
component after long time operation. AUO strongly recommend the design value of
LED driver board OVP (over voltage protection) should be 10% higher than max. value
al
rn
Note 4-6: AUO strongly recommend “Analog Dimming” method for backlight brightness
In
control for Wavy Noise Free. Otherwise, recommend that Dimming Control Signal
AR
5 Reliability Test
AUO reliability test items are listed as following table. (Bare Panel only)
15
Low Temperature Storage (LTS) Ta= -20℃, 300hours
4/
Acceleration: 1.5 Grms
/0
Vibration Test Wave: Random
14
(Non-operation) Frequency: 10 - 200 Hz
20
Sweep: 30 Minutes each Axis (X, Y, Z)
On
Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
nly
Direction: ±X, ±Y, ±Z (one time for each Axis)
eO
Thermal Shock Test (TST) -20℃/30min, 60℃/30min, 100 cycles Note 5-1
On/Off Test On/10sec, Off/10sec, 30,000 cycles Us
Contact Discharge: ± 15KV, 150pF(330Ω ) 1sec,
8 points, 25 times/ point.
al
Operation:18,000 ft
Altitude Test
AR
Non-Operation:40,000 ft
ST
Note 5-1: a. A cycle of rapid temperature change consists of varying the temperature from -20℃ to
60℃, and back again. Power is not applied during the test.
or
b. After finish temperature cycling, the unit is placed in normal room ambient for at least 4
lF
No data lost
Self-recoverable
id
No hardware failures.
nf
Co
O
AU
6 Shipping Label
M195XTN01.0
15
4/
/0
14
Note 6-1: For Pb Free products, AUO will add for identification.
20
Note 6-2: For RoHS compatible products, AUO will add for identification.
On
Note 6-3: For China RoHS compatible products, AUO will add for identification.
nly
Note 6-4: The Green Mark will be presented only when the green documents have been ready by
AUO Internal Green Team.
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
4/
/0
14
20
On
nly
eO
Us
al
rn
te
In
R
TA
rS
Fo
ial
t
en
id
nf
Co
mechanical design
AU
15pcs/Carton
15
4/
/0
14
20
On
nly
eO
Us
Corner angle Moisture-proof film
al
Stretch film
rn
te
In
Corner angle
ST
or
Pallet
lF
tia
en
id
nf
Co
O
AU
Ver 1.0
Specification
Item Remark
Q'ty Dimension Weight(kg)
Cushion 1 - 2 Kg
15
Packing Box 15 pcs/Box 526(L)mm x 299(W)mm x 335(H)mm 24.15Kg with panel & cushion
4/
Pallet 1 1150(L)mm x 910(W)mm x 138(H)mm 15Kg
/0
Pallet after 18boxes/
1150(L)mm x 910(W)mm x 1143(H)mm 449.7Kg
14
Packing pallet
20
On
nly
eO
Us
al
rn
te
In
AR
ST
or
lF
tia
en
id
nf
Co
O
AU
Ver 1.0